2GIG DREC2-319/345 Dual-Frequency Receiver - Compatibility Sheet

PRODUCT SUMMARY
319-345MHz Dual Receiver
The 2GIG 319/345 MHz Receiver
is designed to be
installed into the 2GIG Control Panel. This Receiver is
a dual frequency device, enabling communication
between the Control Panel and peripheral devices that
use either the 319 or the 345 MHz frequency.
SKU: PN 2GIG-DREC2-319
UPC: 8-17082-01053-3
FEATURES
SETUP
• GE-compatible 319MHz wireless
protocol
• Accepts up to 48 wireless devices
using 2GIG, Honeywell, or GE
protocols
• External antenna provides reliable
range performance
• Integrates into the panel itself, so no
need for an external power supply
• No need to hide additional translator
hardware
• Easy to install into any Go!Control
panel
All currently supported 345MHz sensors will continue to communicate to the Go!Control.




31
9
Hz
w
ir
el
es
s
BEFORE INSTALLING
1
Disconnect the power from the Control Panel.


1a Un-plug the AC Power Supply.


1b Open the Control Panel.


1c Disconnect the backup battery.
2
To disconnect the 900 MHz Transceiver Module
inside the Control Panel, pull straight up.
(FIG.1)
If
you don’t pull the module straight up, there is a
danger of breaking either the 3-pin or 5-pin
connectors.
TIP:
The module is located behind the Home Button on
the main circuit panel.
INSTALLING THE 319/345 RECEIVER
1
Align the 319/345 MHz Receiver to
the 3-Pin Connector.
(FIG.2)
2
While maintaining previous
alignment with the 3-pin
connector, align the 319/345
Receiver to the 5-pin Connector.
3
Press down on the foam pressure
pad to seat the receiver.
(FIG.3)
4
After the receiver is properly
seated, hold the receiver in place
(in the control panel) while
inserting the antenna plug fully
into the 319/345 MHz Receiver
antenna mating connector.
MOUNTING THE ANTENNA
1
Thread the antenna through the
back of the Control Panel into the
wall
(FIG.4)
.
2
Reconnect the battery.
3
Close the Control Panel.
4
Plug in the AC Power Supply.
(FIG.1)
(FIG.2)
(FIG.3)
(FIG.4)
IMPORTANT: This 319/345 MHz Receiver excludes the
use of the 2GIG-TS1 Wireless Keypad and Image Sensor! For all product announcements, datasheets, technical
information, etc., visit the 2GIG dealer site at
dealer.2gig.com
or email us at
2gigtechsupport@linearcorp.com
319-345MHz Dual Receiver
GE SENSOR COMPATIBILITY
PRODUCT SUMMARY
Fully Compatible with Go!Control panels without modi
fi
cations
SKU DESCRIPTION
NOTES
60-458-10-319.5
Single-Button Panic
60-460-01-95
Heat Detector, Wireless (200 degree)
60-460-319.5
Heat Detector, Wireless (135 degree)
60-462-10-319.5 or NX-656
Glassguard Sensor - White
60-462-11-319.5 or NX-657
Glassguard Sensor - Brown
60-499-10-319.5 or NX-452
Slim Line Door/Window Sensor
60-504-10-319.5 or NX-658
Freeze Sensor
60-511-02-95
DS924i Pet Immune PIR Motion Sensor
60-578-10-95 or NX-475
Water Resistant Pendant Panic
60-607-319.5
2-Button Keychain Touchpad
60-639-95R or NX-480
Indoor/Outdoor SAW PIR Motion Sensor
60-639-95R-OD
Indoor/Outdoor SAW PIR Motion Sensor
60-670-95R or NX-450
SAW Door/Window Sensor
60-688-95 or NX-454
Micro Door/Window Sensor
60-741-95
Micro Recessed Door/Window Sensor
60-742-95R
SAW Freeze Sensor
60-744-95R or NX-695
Water Sensor SAW
60-834-95 or NX-487
Adjustable Dual Technology Sound Sensor
60-880-95 or NX-482
AP750W Wireless PIR Motion Sensor
60-807-95R or NX-481
Indoor Pet Immune SAW PIR Motion Sensor
TX-1010-01-1
DesignLine Slim Door/Window Sensor - white
TX-1010-01-3
DesignLine Slim Door/Window Sensor - Brown
TX-1510-01-1
DesignLine Recessed Door/Window Sensor
TX-6010-01-1
Photoelectric Smoke Alarm
TX-8010-01-1
DesignLine Garage Door Sensor
TX-8300-01-1
DesignLine Tri-Zone Wireless 3-in-1 Sensor
600-1064-95R
Micro SAW Keyfob
"Lock" arms away, "Unlock" disarms, "Light" arms stay, "*" works when programmed
60-606-319.5
4-Button Keychain Touchpad
"Lock" arms away, "Unlock" disarms, "Light" arms stay, "*" works when programmed

Working with minor issues
60-362N-10-319.5 or NX-650N Door/Window Sensor - White
No external loop
60-362-10-319.5 or NX-650
Door/Window Sensor - Brown
No external loop
60-362-11-319.5 or NX-650
Door/Window Sensor - Belgian Grey
No external loop
60-457-10-319.5
Double Button Panic
"Light" button function unknown
60-452-10-319.5
Pendant Panic
To learn in, must manually convert GE HEX ID to decimal ID*


(will not learn in by tamper)
60-873-95 or NX-488
ShatterPro Glassbreak Sensor
To learn in, must manually convert GE HEX ID to decimal ID*


(will not learn in by tamper)
60-906-95
Micro Wrist Watch Panic Button
To learn in, must manually convert GE HEX ID to decimal ID*


(will not learn in by tamper)
60-886-11-95 or NX-668
Shock Sensor - Brown
Dip switch #5 must be in down position, shock sensor only,


reed switch doesn't work
60-886-95 or NX-667
Shock Sensor - White
Dip switch #5 must be in down position, shock sensor only,


reed switch doesn't work
* Options to help convert HEX ID to decimal ID

Web -
easycalculation.com/hex-converter.php
Mobile app -
Binary Octal Decimal Hex Calculator