Aeon Labs Heavy Duty Smart Switch - Install Instructions Gen 5

http://aeot.ec/spprt/heavyduty
View t
he d
igital m
anual:
Aeot
ec b
y A
eon Labs Hea
vy D
ut
y Smar
t S
wit
ch G
en5.
Quick start
Familiarise yourself with your Heavy Duty Smart Switch Gen5.
Z-W
ave ne
twor
k inst
ruc
tions
.

Your high-powered utilities and services don't always have to be turned on.

They don't always have to be costing you money.

With Heavy Duty Smart

Switch you'll have full control of them. You'll have the ability to wirelessly turn
them on or off using Z-Wave . You'll be able to do it

remotely and you'll be

able to do it with an automatic schedule. You'll also be able to save money
immediately when you use Heavy Duty Smart Switch's

inbuilt energy



monitoring capabilities. You'll receive real-time reports of just

how much

electricity you're paying for.

You'll then be able to use scheduling and
automatic controls to reduce the money

you spend on appliances that need

up to 40 amps of power.
Action
button
: Used
for
Heavy

Duty
Smart
Switch

Z-W
ave
network
inclusion and exclusion and to manual
ly turn on or off.
Warning: Be careful

of electric shock. Only installation and maintenance
personnel should operate this button and get rid of the paragraph break.
Status LED
: Indicates your Heavy Duty Smart Switch’s status;
Terminals
:
There are two groups of
terminals.
As marked, mains power is to

be connected to AC Power and the electric load to Load.
Important:
A licensed
electrician
with
knowledge
and
understanding
electrician
systems
and
electrical
safety
should
complete
the
electrical
installation.
Important
: Heavy
Duty
Smart
Switch

Gen5

must
wired
behind
an

air

break switch for safety and electric appliance.

1.
Mount your Heavy Duty Smart Switch on a wall as shown:




2.
Loosen
your
Heavy Duty Smart Switch’s
lower
screw
to
release
its shell.

Remove the shell to reveal the inner electronics.
3.
Prepare

the
wires
you
will
be
attaching
to
your
Heavy Duty Smart Switch



by stripping them to the necessary length. Add wire terminals to each wire.
4.
Your Heavy Duty Smart Switch

must be paired with

a Z-Wave network




before

it can receive wireless commands or report the energy consumption
of the attached electronics.


Note:
The LED on your Heavy Duty Smart Switch will blink if it is not





currently paired with a Z-Wave network.
Tip:
Turn off any devices connected to your Heavy Duty Smart Switch
before

adding

or removing it to / from a Z-Wave network. This will help to
prevent load damage.
5.
Power on your Heavy Duty Smart Switch. At

this stage you need to add it



to your Z-Wave network.

If you're using an

Aeotec Z-Stick
or
Minimote, please

refer the “Z-Wave Network Instructions”

section of this user guide.

If you're

using an alternative gateway, please refer to the
respective
section of its user
manual using your Heavy Duty Smart Switch's Action Button to put it into
inclusion mode.




Note:
1.Your switch should be installed in a ventilated area with good heat
dissipation.
2.Your switch should access to the protective earth (green/yellow) line.
3.Your switch should have front-end access to a short-circuit protection.
4.Only professionals should install, repair, or open your switch’s casing.
6.

Once added to your Z-Wave network, replace your Heavy Duty Smart
Switch's shell, refastening it.


Before
wiring,
you
must
switch
of f the
air
break
switch
and
confirm
that the
circuit power is down.
If the
air
break
switch
is out
of
sight,
please
lock
it to

‘OFF’ position and tag it to prevent unexpecte
d application of power.
3
Adding your Heavy Duty Smart Switch Gen5 to a Z-Wave network.
4
Action Button
Action Button
Status LED
Wire Terminals
N: Blue
L: Brown
GND: Green / yellow
GND: Green / yellow
N: Blue
L: Brown

Air Break Switch
Load
Input
Output
Heavy Duty Smart Switch Gen5
8AWG Wire terminal (x8)
10AWG Wire terminal (x8)
Screws (x2)
Instruction Manual

®
7.
The
product can be mounted on a wall or surface
. To do so, drill a ø2.5mm
hole that corresponds to the up upper part of your switch.

Drill a second hole
138mm below this. Affix screws. Your installation is now complete.


If y
ou
’re using a Z
-S tick
:
1. Decide on where you want your Heavy Duty Smart Switch to be placed
and set it up as per the Quick Start guide steps 1 to 5. Its Status LED will
begin to blink.
2. If your Z-Stick is plugged into a gateway or a computer, unplug it.
3. Take your Z-Stick to your Heavy Duty Smart Switch.
4. Press the Action Button on your Z-Stick.
5. Press the Action Button on your Heavy Duty Smart Switch.
6. If

your switch has been successfully linked to your Z-Wave network, its
Status LED will no longer blink. If the linking was

unsuccessful, the Status
LED continues to blink. Repeat the above steps.
7. Press the Action Button on your Z-Stick to take it out of installation mode.



If y
ou
’re using a Minimote:
1. Decide

on where you want your Heavy Duty Smart Switch to be placed
and set it up as per the Quick Start guide steps 1 to 5. Its Status LED will
begin to blink.
2. If your Minimote is plugged into a gateway or a computer, unplug it.





Important:

You must make sure the wire terminals are connected firmly


with each corresponding terminal on your Heavy Duty Smart Switch.
Please pay attention to the power and current of equipment. If the current is
less than 32A, you can use AWG10# wire. If the current exceeds 32A,
please use AWG8# wire.

Warning: Device current can not exceed 40A.
Wire your
Heavy Duty Smart Switch
according to the following diagram. As



shown

below, connect each

live

lines from Air Break Switch to the
corresponding terminals marked L on your Heavy Duty Smart Switch.
If there is a Neutral line and GND from the Air Break Switch

please
respectively
connect them to the terminals
labelled N and GND.

Similarly,
wire the electric load with your

Heavy Duty Smart Switch
. As a final step,
tighten the screws to the wire terminals.




Monitoring power consumption.
Technical speciations.
War ran
ty.
Do
not
dispose
of
electrical
appliances
as
unsorted
municipal
waste,
use
separate collection facilities.
Contact
your
local
government
for
information
regarding
the
collection
systems available.
Take your Z-Stick to your Heavy Duty Smart Switch.
Press the
Action Button on your Z-Stick.
Press the
Action Button on your Heavy Duty Smart Switch.
If your
Heavy
Duty
Smart
Switch
has
been
successfully
removed from
your
network,

its Status LED

will
blink.
If the
removal
was
unsuccessful,

its Status LED will not blink.
Press the
Action Button on your Z-Stick to take it out of removal mode.
Take your Minimote to your Heavy Duty Smart Switch.
Press the Remove Button on your Minimote.
Press the
Action Button on your Heavy Duty Smart Switch.
If your
Heavy
Duty
Smart
Switch

has
been
successfully
removed from
your
network,
its Status LED

will
blink.
If the
removal
was
unsuccessful,

its Status LED will not blink.
Press any button on your Minimote to take it out of removal mode.

You

can
remove
your Heavy Duty Smart Switch

from
your
Z-W
ave network
at

any
time.
To do
this
you
need
use
your

main
controller
such
as a Z-Stick
or Minimote.
Your
Heavy
Duty
Smart
Switch


can
be
turned
on
or of f through
the
use of
Z-W
ave
commands
built
into
Z-Wave
certified
controllers
and
gateways.
The
specific
Z-W
ave
commands
supporting
this
function
are
the
Basic
Command
Class
and
Binary
Switch Command
Clas
s. Plea
se cons
ult the
operation manual for your Z-Wave network controller for specific
instructions on controlling your Heavy Duty Smart Switch.
Y
our Heavy Duty Smart Switch


Aeon
Labs
warrants
to
the
original
purchaser
of
Products
that
for
the
Warranty
Period
(as
defined
below),
the
Products
will
be
free
from
material
defects
in
materials
and
workmanship.
The
foregoing
warranty
is subject
to
the
proper
installation,
operation
and
maintenance
of
the
Products
in
accordance
with
installation
instructions
and
the
operating
manual
supplied
to
Customer
. Warranty
claims
must
be
made
by
Customer
in writing
within
thirty
(30)
days
of the
manifestation
of a problem.
Aeon
Labs'
sole
obligation
under
the
foregoing
warranty
is,
at Aeon
Labs'
option,
to
repair
, replace
or
correct
any
such
defect
that
was
present
at
the
time
of
deliver
y, or
to
remove
the
Products and to refund the purchase price to Customer
.
The
"W
arranty
Period"
begins
on
the
date
the
Products
is
delivered
and
continues for 12 months.
Any
repairs
under
this
warranty
must
be
conducted
by
an
authorized
Aeon
Labs
service
representative
and
under
Aeon
Labs'
RMA
polic
y. Any
repairs
conducted by unauthorized persons sh
all void this warrant
y.
Excluded
from
the
warranty
are
problems
due
to
accidents,
acts
of
God,
civil
or
military
authority
, civil
disturbance,
war
, strikes,
fires,
other
catastrophes,
misuse,
misapplication,
storage
damage,
negligence,
electrical
power
problems, or modification to the Produ
cts or its components.
Aeon
Labs
does
not
authorize
any
person
or
party
to
assume
or
create
for
it
any
other
obligation
or
liability
in connection
with
the
Products
except
as
set
forth herein.
Aeon
Labs
will
pass
on
to Customer
all manufacturers'
Material
warranties
to
the
extent
that
they
are
transferable,
but
will
not
independently
warrant
any
Material.
Customer
must
prepay
shipping
and
transportation
charges
for
returned
Products,
and
insure
the
shipment
or
accept
the
risk
of loss
or
damage
during
such
shipment
and
transportation.
Aeon
Labs
will
ship
the
repaired
or
replacement products to Customer freight prepaid.
Customer
shall
indemnif
y, defend,
and
hold
Aeon
Labs
and
Aeon
Labs'
af filiates,
shareholders,
directors,
of ficers,
employees,
contractors,
agents
and
other
representatives
harmless
from
all
demands,
claims,
actions,
causes
of
action,
proceedings,
suits,
assessments,
losses,
damages,
liabilities,
settlements,
judgments,
fines,
penalties,
interest,
costs
and
expenses
(including
fees
and
disbursements
of
counsel)
of
every
kind
(i)
based
upon
personal
injury
or
death
or
injury
to
property
to
the
extent
any
of
the
foregoing
is proximately
caused
either
by
a defective
product
(including
strict
liability
in
tort)
or
by
the
negligent
or
willful
acts
or
omissions
of
Customer
or
its
of ficers,
employees,
subcontractors
or
agents,
and/or
(ii)
arising
from
or
relating
to
any
actual
or
alleged
infringement
or
misappropriation
of any
patent,
trademark,
mask
work,
copyright,
trade
secret
or
any
actual
or
alleged
violation
of
any
other
intellectual
property
rights
arising
from
or
in connection
with
the
products,
except
to the
extent
that
such
infringement exists as a result of
Aeon Labs' manufacturing processes.
IN
NO
EVENT
SHALL
AEON
LABS
BE
LIABLE
FOR
ANY
INDIRECT
,
INCIDENT
AL,
PUNITIVE,
SPECIAL
OR
CONSEQUENTIAL
DAMAGES,
OR
DAMAGES
FOR
LOSS
OF
PROFITS,
REVENUE,
OR
USE
INCURRED
BY

CUST
OMER
OR
ANY
THIRD
PAR
TY
, WHETHER
IN
AN
ACTION
IN
CONTRACT
, OR
TOR
T, OR
OTHER
WISE
EVEN
IF
ADVISED
OF
THE
POSSIBILIT
Y OF
SUCH
DAMAGES.
AEON
LABS'
LIABILITY
AND
CUST
OMER'S
EXCLUSIVE
REMEDY
FOR
ANY
CAUSE
OF
ACTION
ARISING
IN
CONNECTION
WITH
THIS
AGREEMENT
OR
THE
SALE
OR
USE
OF
THE
PRODUCTS,
WHETHER
BASED
ON
NEGLIGENCE,
STRICT

LIABILITY
, BREACH
OF
WARRANT
Y, BREACH
OF
AGREEMENT
, OR
EQUIT
ABLE
PRINCIPLES,
IS
EXPRESSL
Y LIMITED
TO,
AT AEON
LABS'
OPTION,
REPLACEMENT
OF
, OR
REP
AYMENT
OF
THE
PURCHASE
PRICE
FOR
THA
T POR
TION
OF
PRODUCTS
WITH
RESPECT
TO WHICH
DAMAGES
ARE
CLAIMED.
ALL
CLAIMS
OF
ANY
KIND
ARISING
IN
CONNECTION
WITH
THIS
AGREEMENT
OR
THE
SALE
OR
USE
OF
PRODUCTS
SHALL
BE
DEEMED
WAIVED
UNLESS
MADE
IN
WRITING
WITHIN
THIR
TY
(30)
DA
YS
FROM
AEON
LABS'S
DELIVER
Y, OR
THE
DA
TE FIXED FOR DELIVE
RY IN
THE EVENT
OF NONDELIVER
Y.
THE
INDEMNITY
AND
WARRANTY
IN
ABOVE
ARE
EXCLUSIVE
AND
IN
LIEU
OF
ALL
OTHER
INDEMNITIES
OR
WARRANTIES,
WHETHER
EXPRESS
OR
IMPLIED,
INCLUDING
THE
IMPLIED
WARRANTIES
OF
MERCHANT
ABILITY
AND FITNESS FOR
A P AR
TICULAR PURPOSE.
If your Z-Stick is plugged into a gateway or a computer, unplug it.
If you are using a Z-Stick:
If you are using a Minimote:
Removing your Heavy Duty Smart Switch Gen5 from a Z-Wave
Network
Turn your Heavy Duty Smart Switch Gen5 on or off.
Action Button
Include
1.
2.
3.
4.
5.
6.
1.
2.
3.
4.
5.
5
6
Model number: ZW078-B/C
Waterproof: IP44
Power Consumption: 1W
Ratings: 240VAC, 50/60Hz;
Maxim 9600 Watts 40A Resistor;
240VAC 5HP AC Motor;
RF range: 600ft/200m outdoor;
Endurance of 10ms period peak current of 1440A
Environmental Conditions: Indoor use;
Altitude up to 2000m;
Ambient temperature 5°C to 40°C;
Max. relative humidity 80%;
Pollution degree 2.
W
arning
www.aeotec.com
Ve
rsion
:
501001000002-AA
Z-Wave and Z-Wave Plus are registered trademarks of Sigma Designs and its subsidiaries
in the United States and other countries
Adv
anc
ed f
unc
tions
.
3. Take your Minimote to your Heavy Duty Smart Switch.
4. Press the Action Button on your Heavy Duty Smart Switch.
5. If

your Heavy Duty Smart Switch has been successfully linked to your
Z-Wave network, its Status LED

will no longer blink. If the linking was


unsuccessful, the Status LED continues to blink. Repeat the above steps.
6. Press any button on your Minmote to take it out of installation mode.
Remove
7
Once synced with a gateway, you’ll be able to configure your switch from it.
Please refer to your

software’s user guide for precise instructions on
configuring your Heavy Duty Smart Switch to your needs.

Tip:
If the
Status
LED
of
your
Heavy
Duty
Smart
Switch
does
not

blink when
it’ s first
powered
up
it means
that your Heavy Duty Smart Switch is already
part of another Z-Wave network.
To rectify this, first follow the subsequent
removal instructions before following the
section 4 of this guide.

To include your Heavy Duty Smart Switch with other controllers

please
consult the operation manual for these controllers on how to include Z-Wave
products into an existing network.
If you are using another gateway:

can
report

Watts
energy
usage
or
KWh
energy
usage
to a Z-W
ave
gateway
or
controlle
r.
If this
function
is supported
by
the
gateway/controlle
r, your energy consumption will be displayed

within

its user interface.


The
specific
Z-W
ave
commands

supporting
energy

monitoring
are
the
Meter

Command

Class
and
Multilevel

Sensor
Command
Class. Automatic reports go to association group 1, which is

setup via the
Association

Command Class.
Please consult your gateway’s /
controller's
manual for instructions on

monitoring energy consumption through your
Heavy Duty Smart Switch.