Alarm.com Aeotec LED Light Bulb - Quick Start Guide

Aeotec LED Light Bulb - Quick Start Guide
To add the Aeotec LED light bulb into a Z-Wave network:
1.
Install the LED bulb into a standard E27 socket.
2.
Turn on the LED bulb using the wall or lamp switch.
3.
Put the panel into Z-Wave Add mode. For panel-specific information about this process, see
Panels
.
4.
Turn off the LED bulb using the switch and immediately turn it back on.
•
If the LED bulb is triggered properly and added to the Z-Wave network, it will flash green for approximately three
seconds and then turn solid white.
•
If the LED bulb is not triggered properly and is not added to the Z-Wave network, it will stay colored and not turn
white. Please try triggering the bulb again.
•
If you are unable to add the bulb to your network, it may already have been added to another network. Follow the
procedure for deleting the bulb from a Z-Wave network and try the Add procedure again.
To delete the Aeotec LED light bulb from a Z-Wave Network:
1.
Verify that the light switch is in the
On
position.
2.
Put the panel into Z-Wave Delete mode. For panel-specific information about this process, see
Panels
.
3.
Flip the switch to turn the LED bulb off/on three times within two seconds (off, on, off, on, off, on).
•
If the LED bulb is triggered properly and deleted from the Z-Wave network, it will turn yellow/orange and then turn
white.
•
If the LED bulb is not triggered properly and is not deleted from the Z-Wave network, it will stay solid. Please try
triggering the bulb again.
To check if the LED bulb has already been added to a Z-Wave network:
1.
Verify that the light switch is in the
On
position.
2.
Flip the switch to turn the LED bulb off/on three times within two seconds (off, on, off, on, off, on).
•
If the LED bulb has already been added to a Z-Wave network and is still part of that network, it will flash orange,
turn red, and then return to the same solid color it was before the test.
•
If the LED bulb is not currently in a Z-Wave network, it will flash blue for at least three seconds, turn solid orange,
and then become white.
https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Lights/Light_Bulbs/Aeotec_LED_Light_Bulb_-_Qui...
Updated: Mon, 14 Oct 2019 18:39:28 GMT
1 To put the LED bulb in color selection mode:
If the LED bulb
is not currently in a Z-Wave network:
1.
Verify that the light switch is in the
Off
position.
2.
Flip the switch to the
On
position three times within two seconds (on, off, on, off, on). The bulb is now in color
selection mode. It will turn solid white and then begin cycling through all of the available colors.
3.
Flip the switch to the
Off
position when the color you desire is displayed.
4.
You may now turn the LED bulb on and off for normal use with your selected color.
If the LED bulb
is
currently in a Z-Wave network:
1.
Verify that the light switch is in the
Off
position
2.
Flip the switch to
On
three times with two seconds (on, off, on, off, on). The bulb is now in color selection mode. It
will cycle through all of the available colors.
3.
Flip the switch to the
Off
position when the color you desire is displayed.
4.
You may now flip
the switch to
On
and control the bulb from the Customer Website and app.
Note
: The dimming feature is not currently supported.
To view and control multi-color lights using the Customer app:
1.
Tap the
circle next to the light bulb icon
to access the color picker for real-time control.
2.
The color picker will show the color most recently requested.
3.
Color commands are sent immediately after a new color is selected. Colors will not be added to the Recent section
until the customer taps
Done
.
https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Lights/Light_Bulbs/Aeotec_LED_Light_Bulb_-_Qui...
Updated: Mon, 14 Oct 2019 18:39:28 GMT
2 Communicating with multi-color lights:
Customers can communicate events with multi-color lights using the
Rules
page on the Customer Website. Examples of
rules include turning the bulb green when someone crosses the Geo-fence, blue if the water sensor triggers, and red for
an alarm.
1.
Log into the Customer Website.
2.
In the
Lights
card, click
.
3.
Click
Rules
.
4.
Click
+ Add New Rule
.
Maximizing comfort through Scenes and schedules
Multi-color lights can also be included in Scenes and schedules. This feature can improve comfort and even sleep
cycles by waking up to cool lights and relaxing in the evening with warm lighting. Scenes can be edited to include multi-
color lights from both the Customer Website and app.
https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Lights/Light_Bulbs/Aeotec_LED_Light_Bulb_-_Qui...
Updated: Mon, 14 Oct 2019 18:39:28 GMT
3