Altronix 6062 - Multi-function Timer Relay - Install Guide

Installation Instructions:
1.
Mount 6062 in desired location/enclosure.
2.
Set proper DC Input Voltage DIP Switch 3: 12VDC ON, 24VDC OFF.
3.
Refer to
DIP Switch Selection
and
Jumper Selection Tables
for desired functions (e.g.: Timing, Trigger, Pulse)
4.
Measure DC input voltage before powering device to ensure proper operation.
5.
Refer to
Terminal Identification Table
and
Typical Applications fig. 1 through fig. 8.
for desired wiring connections.
Note:
When triggering via a N.O. (normally open), momentary or maintained trigger, connect the dry contact trigger to

Pos (+) and TRG terminals. When triggering via a N.C. (normally closed), momentary or maintained trigger, connect

the trigger to Neg. (–) and TRG terminals and install a resistor [for 12VDC - 2K (2,000 ohm) or

for 24VDC - 4.7K (4,700 ohm)] between the Pos (+) and TRG terminals
(Fig. 8).
6.
Enable the reset features:

- Cut J3 when power is removed the timer will reset and not re-trigger when power is restored unless a new trigger is applied.

Note:
The closed trigger and delayed pulse options will not operate if the reset feature is desired.
DIP Switch Selection Table:
DIP #
Off
On
1
Relay energizes at the start of timing cycle.*
Relay energizes at the end of timing cycle.*
2
1-60 Minutes timing range (trimpot adjustable).
1-60 Seconds timing range (trimpot adjustable).
3
24VDC operating voltage.
12VDC operating voltage.
4
Timing begins immediately upon trigger input.
Timing starts after removal of trigger input.
* When relay energizes (LED is on) [N.O. & C] switch from open to close and [N.C. & C] switch from close to open.
Jumper Selection Table:
Number
Function/Description
J1
Cutting J1 selects the pulser/flasher mode.
Relay will flip ON and OFF continuously in equally set timed intervals when timer is powered up.
J2
Cutting J2 puts timer in delayed output mode.
Relay will pulse for 1 second at the end of a preset timing cycle. *DIP Switch 1 must be ON for this function.
J3
6062 will go through an initial timing cycle when first powered up unless J3 is cut.
If J3 is cut, timing can only be initiated via TRG terminal.
Terminal Identification:
Terminal Legend
Function/Description
TRG
Applying a positive voltage will activate timing cycle.
Trigger voltage range: 7-12VDC at 12 volt setting, 15-24VDC at 24 volt setting.
– , +
Connect 12 or 24VDC filtered and regulated voltage.
Refer to
DIP Switch Selection Table
for voltage setting.
N.O., C, N.C.
Dry form “C” relay contacts are rated 8A at 120VAC/28VDC.
Input:
• 12VDC or 24VDC operation is selectable.
Current Draw:
• Stand-by: 3mA, Relay energized: 40mA.
Relay:
• Selectable relay activation at the start or end of the timing cycle.
• One (1) second momentary relay activation at the end of
the timing cycle (eliminates the need to use two (2)
timers for this function).
Visual Indicators:
• LED indicates relay is energized.
Electrical:
• Operating temperature: -20º C to 49º C ambient.
Features:
• Triggers via positive DC (+) voltage, dry contact closure,
or removal of contact closure.
• Quick and extremely accurate time range adjustment
from 1 second to 60 minutes.
• Built-in reset feature that cancels timing cycle.
• Repeat (flasher/pulse) mode.
Mechanical:
• Snap Trac compatible (order Altronix model #ST3).
• Board Dimensions (L x W x H approx.):
3” x 2.5” x 0.75” (76.2mm x 63.5mm x 19.05mm).
• Product weight (approx.): 0.1 lb. (0.05 kg).
• Shipping weight (approx.): 0.15 lb. (0.07 kg).
6062
Multi-Purpose Timer
Overview:
Model 6062 programmable timer is suitable for many functions that require a timed operation e.g. Access Control Applications,
Siren/Bell Cut Off Module, Dialer Delay, Guard Tour Supervisory Timer, etc. Some optional functions include: One Shot, Delayed
Release, Delayed Operate, Delayed Pulse and Pulser/Flasher. A new feature has been added which provides a momentary relay acti-
vation at the end of a desired timing cycle. This feature eliminates the need for having to use two (2) timers to achieve this function.
Specifications: 6062 Typical Applications:
Fig. 1 -
Timed Door Annunciator:

Fig. 5 -
Timed Door Strike:
For this application Switch #1 and Switch #4
For this application Switch #1 should be in the OFF position and
should be in the OFF position.
Switch #4 should be in the ON position.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Fig. 2 -
Guard Tour Supervisory Timer:

Fig. 6 -
Timed Shunt for a Door: Use to bypass alarm contacts.
For this application Switch #1 and Switch #4
For this application Switch #1 should be in the OFF position and
should be in the OFF position.
Switch #4 should be in the ON position.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Fig. 3 -
Swinger Eliminator:

Fig. 7 -
Bell Cut Off Timer:
For this application Switch #1 should be in the OFF
For this application Switch #1 should be in the ON position and
position and Switch #4 should be in the ON position.
Switch #4 is not used in this application.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Fig. 4 -
Delay Timer:

Use for Door Ajar Alarm,
Fig. 8 -
Closed Circuit Trigger Option:
Delayed Activation of Digital Dialer,
Defrost Cycle Timer, etc...
For this application Switch #1 should be in the ON
For this application a resistor [for 12VDC - 2K (2,000 Ohm) or for
position and Switch #4 is not used in this application.
24VDC - 4.7K (4,700 Ohm)] must be installed as shown

(resistor not supplied).
TRG
--
+
Closed
Circ
uit
Contact
Pull up
Resistor
Power
Supply
+
---
TRG
--
+N
OC
NC
1
ON
ON
1 2 3 4
OFF
15
CUT J3 FOR RESET
ON POWER-UP
TRIG CONTROL
12V / 24V
SEC. / MIN.
RELA
Y CONTROL
CHIME
Pos (+) and Neg (--
)
terminals constant
12VDC or 24VDC
Normally Open
Door Contacts
+
---
+
---
4
3
2
1
J3
CUT J2 FOR DELA
Y PULSE J2
CUT J1 FOR REPEA
T J1
45
60
TRG
--
+N
OC
NC
1
ON
ON
1 2 3 4
OFF
15
CUT J3 FOR RESET
ON POWER-UP
TRIG CONTROL
12V / 24V
SEC. / MIN.
RELA
Y CONTROL
Pos (+) and Neg (--
)
terminals constant
12VDC or 24VDC
Normally Open
Door Contacts
Door Strike
+
---
+ ---
4
3
2
1
J3
CUT J2 FOR DELA
Y PULSE J2
CUT J1 FOR REPEA
T J1
45
60
TRG
--
+N
OC
NC
1
ON
ON
1 2 3 4
OFF
15
CUT J3 FOR RESET
ON POWER-UP
TRIG CONTROL
12V / 24V
SEC. / MIN.
RELA
Y CONTROL
DIALER OR
TRANSMITTER
Pos (+) and Neg (-- )
terminals constant
12VDC or 24VDC
Normally Open
Switch Contacts
+
---
4
3
2
1
J3
CUT J2 FOR DELA
Y PULSE J2
CUT J1 FOR REPEA
T J1
45
60
TRG
--
+N
OC
NC
1
ON
ON
1 2 3 4
OFF
15
CUT J3 FOR RESET
ON POWER-UP
TRIG CONTROL
12V / 24V
SEC. / MIN.
RELA
Y CONTROL
Pos (+) and Neg (--
)
terminals constant
12VDC or 24VDC
Door Contacts
Protective
Circ
uit
+
---
4
3
2
1
J3
CUT J2 FOR DELA
Y PULSE J2
CUT J1 FOR REPEA
T J1
45
60
Normally Open
Switch Contacts
TRG
--
+N
OC
NC
1
ON
ON
1 2 3 4
OFF
15
CUT J3 FOR RESET
ON POWER-UP
TRIG CONTROL
12V / 24V
SEC. / MIN.
RELA
Y CONTROL
Closed
Circ
uit
Zone on
Contr
ol Panel
Pos (+) and Neg (--
)
terminals constant
12VDC or 24VDC
Protective
Circ
uit
+
---
4
3
2
1
J3
CUT J2 FOR DELA
Y PULSE J2
CUT J1 FOR REPEA
T J1
45
60
TRG
--
+N
OC
NC
1
ON
ON
1 2 3 4
OFF
15
CUT J3 FOR RESET
ON POWER-UP
TRIG CONTROL
12V / 24V
SEC. / MIN.
RELA
Y CONTROL
Use appr
opriate contacts
to re
porting devices
Normally Open
Triggering Device
Pos (+) and Neg (--
)
terminals constant
12VDC or 24VDC
+
---
4
3
2
1
J3
CUT J2 FOR DELA
Y PULSE J2
CUT J1 FOR REPEA
T J1
45
60
TRG
--
+N
OC
NC
1
ON
ON
1 2 3 4
OFF
15
CUT J3 FOR RESET
ON POWER-UP
TRIG CONTROL
12V / 24V
SEC. / MIN.
RELA
Y CONTROL
Bell
or
Sir
en
+
---
4
3
2
1
J3
CUT J2 FOR DELA
Y PULSE J2
CUT J1 FOR REPEA
T J1
45
60
Bell
Output
Contr
ol Panel
12VDC or 24VDC
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty
II6062 - Rev. 032211
I13U
MEMBER