DSC RM-2 - Installation Manual

RM-2 Relay Module
Installation Instructions
The RM-2 Relay Module is used as an end-of-line (EOL) power supervision module for
4-wire smoke detectors. The RM-2 is used with the Polarity Reversal Module PRM-
4W and DSC FSA-410 series smoke detectors.
When the PRM-4W reverses polarity on the smoke detector loop to activate all smoke
detector sounders, the RM-2 Relay will continue to operate normally (regardless of
input power polarity). Refer to the PRM-2W/4W Polarity Reversal Module Installation
Instructions
Technical Specifications:
Operating Voltage Range: .............................................................10V
DC
to 30V
DC
Relay Conta
ct Rating:
.....................................................................2A@30
V
DC
/V
AC
Current Rating: .............................................................................................. 25mA
Operating Environment: ................................................... 0°C - 49°C (32°F - 120°F)
..............................................................................5% - 93% RH (non-condensing)
Size (H x W x D): ................................... 28.5 x 86 x 21mm / 1
1
/
8
x 3
3
/
8
x
7
/
8
in.
Terminal Wire Gauge:............................................................................14-22 AWG
Connection Diagram
Run the connection wires through the wiring holes on the back of the unit.
Mounting
To mount the unit, remove the plastic cover and secure the unit to the desired loca-
tion with the screws provided. Replace the cover.
The module can also be mounted inside a standard 4” electrical box (1.5” deep) if
required by the installation. Please refer to the diagrams below:
P+
P-
PRM-4W
Polarity Reversal Module
Zx Com
Control Panel
FSA-410 Series
4-wire Smoke Detector
NO C
12 V
DC
BLK
RED
NO
Panel EOLR
DSC RM-2 Relay
COM
NC
4-WIRE SMOKE DETECTORS
Mounting of the Relay in an Electrical Box
LIMITED WARRANTY
Digital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the
product shall be free of defect in materials and workmanship under normal use and that in fulfilment of
any breach of such warranty, Digital Security Controls Ltd. shall, at its option, repair or replace the defective
equipment upon return of the equipment to its repair depot. This warranty applies only to defects in parts
and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond
the control of Digital Security Controls Ltd. such as lightning, excessive voltage, mechanical shock, water
damage, or damage arising out of abuse, alteration or improper application of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other
warranties, whether expressed or implied and of all other obligations or liabilities on the part of Digital Se-
curity Controls Ltd. This warranty contains the entire warranty. Digital Security Controls Ltd. neither as-
sumes, nor authorizes any other person purporting to act on its behalf to modify or to change this
warranty, nor to assume for it any other warranty or liability concerning this product.
In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequential damages,
loss of anticipated profits, loss of time or any other losses incurred by the buyer in connection with the
purchase, installation or operation or failure of this product.
WARNING: Digital Security Controls Ltd. recommends that the entire system be completely tested on a reg-
ular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electri-
cal disruption, it is possible for this product to fail to perform as expected.
4-Wire Smoke Detector
FSA-410x
Smoke Detector
Mounting Plate
Power Supervision
Relay RM-2
Electrical Box
(1.5" deep)
©2003 Digital Security Controls Ltd.
Toronto, Canada •
www.dsc.com
Printed in Canada
Direct all comments concerning this publication to
pubs@dscltd.com RM-2 Relay Module
Installation Instructions
The RM-2 Relay Module is used as an end-of-line (EOL) power supervision module for
4-wire smoke detectors. The RM-2 is used with the Polarity Reversal Module PRM-
4W and DSC FSA-410 series smoke detectors.
When the PRM-4W reverses polarity on the smoke detector loop to activate all smoke
detector sounders, the RM-2 Relay will continue to operate normally (regardless of
input power polarity). Refer to the PRM-2W/4W Polarity Reversal Module Installation
Instructions
Technical Specifications:
Operating Voltage Range: .............................................................10V
DC
to 30V
DC
Relay Contact Rating: .....................................................................2A@30V
DC
/VAC
Current Rating: .............................................................................................. 25mA
Operating Environment: ................................................... 0°C - 49°C (32°F - 120°F)
..............................................................................5% - 93% RH (non-condensing)
Size (H x W x D): ................................... 28.5 x 86 x 21mm / 1
1
/
8
x 3
3
/
8
x
7
/
8
in.
Terminal Wire Gauge:............................................................................14-22 AWG
Connection Diagram
Run the connection wires through the wiring holes on the back of the unit.
Mounting
To mount the unit, remove the plastic cover and secure the unit to the desired loca-
tion with the screws provided. Replace the cover.
The module can also be mounted inside a standard 4” electrical box (1.5” deep) if
required by the installation. Please refer to the diagrams below:
P+
P-
PRM-4W
Polarity Reversal Module
Zx Com
Control Panel
FSA-410 Series
4-wire Smoke Detector
NO C
12 V
DC
BLK
RED
NO
Panel EOLR
DSC RM-2 Relay
COM
NC
4-WIRE SMOKE DETECTORS
Mounting of the Relay in an Electrical Box
LIMITED WARRANTY
Digital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the
product shall be free of defect in materials and workmanship under normal use and that in fulfilment of
any breach of such warranty, Digital Security Controls Ltd. shall, at its option, repair or replace the defective
equipment upon return of the equipment to its repair depot. This warranty applies only to defects in parts
and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond
the control of Digital Security Controls Ltd. such as lightning, excessive voltage, mechanical shock, water
damage, or damage arising out of abuse, alteration or improper application of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other
warranties, whether expressed or implied and of all other obligations or liabilities on the part of Digital Se-
curity Controls Ltd. This warranty contains the entire warranty. Digital Security Controls Ltd. neither as-
sumes, nor authorizes any other person purporting to act on its behalf to modify or to change this
warranty, nor to assume for it any other warranty or liability concerning this product.
In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequential damages,
loss of anticipated profits, loss of time or any other losses incurred by the buyer in connection with the
purchase, installation or operation or failure of this product.
WARNING: Digital Security Controls Ltd. recommends that the entire system be completely tested on a reg-
ular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electri-
cal disruption, it is possible for this product to fail to perform as expected.
4-Wire Smoke Detector
FSA-410x
Smoke Detector
Mounting Plate
Power Supervision
Relay RM-2
Electrical Box
(1.5" deep)
©2003 Digital Security Controls Ltd.
Toronto, Canada •
www.dsc.com
Printed in Canada
Direct all comments concerning this publication to
pubs@dscltd.com