Honeywell 5800CO Installation Manual
Related Products
Related Categories
Document Transcript
5800CO Carbon Monoxide Detector with Built-in Wireless Transmitter
INSTALLATION AND SETUP GUIDE
GENERAL INFORMATION
Normal (standby) Alarm/Test Low Battery Table 1: Detector LED Modes Green LED Blinks every 10 seconds Off Off Red LED Off Blinks every 1 second Blinks every 45 seconds for 37 days Sounder Off Temporal 4 Pattern† Chirp every 45 sec beginning 7 days after LED blinks, continues 30 days One chirp every 45 seconds One chirp every 45 seconds Off
Detector Trouble Detector End-ofLife Power Up
Off Off Blinks every 10 secs††
(w/red LED)
Blinks every 5 seconds Blinks every 10 seconds Blinks every 10 secs ††
(w/green LED)
WARNING: This product is not intended for use in industrial factories or commercial parking garages. Detector Description • Listed to UL standard 2075 CO sensitivity is evaluated to UL 2034 • Supervised • Local sounder • Dual LED’s • Test/Hush button • Surface mount to wall or ceiling • Optional drywall anchors included
††
BATTERY INSTALLATION AND REPLACEMENT
MOUNTING THE DETECTOR
TEST BUTTON
CAR
GREEN LED
AL
AR
T DO NO
M
I PA
RED LED
5800CO-001-V0
N
T
DI AD B C AU T I O N : N SO M AR KING
Figure 1. 5800CO Wireless Carbon Monoxide Detector
PROGRAMMING
Event alarms test low battery detector supervision detector end-of-life detector trouble tamper
Alpha Keypad CO Alarm CO Alarm Lo Bat CO Trouble CO Trouble disarmed = CO Trouble armed = CO Alarm
CS Report CO alarm (CID 162) CO alarm (CID 162) RF low-battery (CID 384) RF sensor supervision (CID 381) sensor trouble - end-of-life (CID 380) RF sensor tamper (CID 383)
B
L
MA
NOR
RBO
TEST
N M O N OXI D DETECTOR
HUSH
E
CA
ENGAGE NOTCH WITH TAMPER RELEASE TAB ON BASE AND TURN CLOCKWISE TO LOCK
Figure 2. Mounting the Detector
S T N A IP M P OF E F R L FO O R C K
FL
AN LO GE CK
DO
ALARM
G: WA R N I N O T M OV E
IN
TI AC O N AL K
TE
ST
HUSH
BO
N
O ON R N M CTP TE DE
XI
DE
O
RM
AL
A
MOUNTING SCREWS (INSTALLED)
B
A
TAMPER RELEASE TAB (CUT OFF SMALL TAB TO ACTIVATE TAMPER RESIST FEATURE)
AL
ARM
N
OT
PA I N
T
NOTE USE SCREW LOCATIONS A OR B AS REQUIRED, THEN ROTATE BASE AND SECURE SCREWS AT EACH MOUNTING SLOT'S ELBOW.
5800CO-006-V0
LEDs
DO N M ALAR I G: R NIN F WA R E TO M OV
O
T
5800CO-003-V0
DO NOT attach the detector to removable ceiling panels. Attach the detector across panel support as shown in Figure 3.
N IN : A D G S DIT O N IO N AL B AC K
CAUTION
RECESSED TEST BUTTON
CA
TEST
RB
Figure 3. Mount Detector Across Ceiling Panel Support
US
H
NORM
O N M O N OXID DETE C TO R
H
Testing Signal Strength
N A ES LA H RM AIR
AL
E
PA I N T
PUSH RECESSED BUTTON WITH A 0.18" MAX. DIAMETER TOOL
IO UT K CA AR M
5800CO-004-V0
Figure 5. Recessed Test Button Opening
BEDROOM
BEDROOM
TO BR
BEDROOM KITCHEN
GARAGE CLOSED DOOR
LIVING ROOM
BASEMENT – CARBON MONOXIDE ALARM LOCATION FOR MULTI-LEVEL RESIDENCE
5800CO-005-V0
Figure 4. Detector Location Diagram
Tamper Protection
Testing Programmed Loops
TESTING THE DETECTOR
NOTE:
Testing Detector Operation
CAUTION: Carbon Monoxide Gas and its Detection
MAINTENANCE
DETECTOR REPLACEMENT
CAUTION
SPECIFICATIONS
UL standard 2075
Please see insert for Limitations of Carbon Monoxide Detectors.
FOR WARRANTY INFORMATION AND FOR DETAILS REGARDING THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM, GO TO: www.honeywell.com/security/hsc/resources/wa
K14631V1 4/08 Rev. B
2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747
Copyright © 2007 Honeywell International Inc. www.security.honeywell.com
- Uploaded