Honeywell 5800PIR-RES Installation Manual

5800PIR-RES Wireless Motion Sensor - Installation Instructions
1
LOCATION / EMPLACEMENT
No / Non / No Satisfactory / Satisfaisant / Satisfactorio

2

OPEN / OUVERTURE

7.5 - 8 ft (2.3 - 2.4 m)

1 2

3

See page GO Panasonic CR123A / SENSOR, CONDUCT GO / NO2 for ENROLL THE more information / Duracell DL123A / PERFORM WALK TEST TEST, AND See page 2 for Honeywell 466 more information
- Use only left OR right side corner mounting holes.

CONNECT THE BATTERY, ENROLL THE SENSOR, CONDUCT GO / NO GO TEST, AND PERFORM WALK TEST / METTRE LES PILES EN PLACE ,

4

MOUNT / INSTALLATION

1
TOP

Observe correct polarity /
Observe correct polarity
Recommended Screws: #6 (3.5 mm)

2

A

DETECTION PATTERNS / COUVERTURE DE
DETECTION 35' / 11m Wide Angle Animal Immune Lens (P/N 5-532-719-00)
Top View / Vue de Dessus

B

ACCESSORIES / ACCESSOIRES
SMB-10 (P/N 0-000-110-01) SMB-10C (P/N 0-000-111-01) SMB-10T (P/N 0-000-155-01)
1 1

Swivel Mount Bracket Swivel Mount Ceiling Bracket Swivel Mount Bracket w/Tamper High Security Lens Kit Pet Alley Lens Kit

20' 0 6m 13' 4m

7' 2m

13' 4m

20' 6m
1 2

27' 8m

35' 11m

3

12

7' 2m 0 7' 2m 13' 4m

4 5 6 7 8 9 10

18

13 14

IS2500-HSLK 35’ x 40’ (11 m x 12 m) IS2500-PALK 35’ x 40’ (11 m x 12 m)
1 2

1

19

15 16 17

20

Not verified by ETL.
1 2

Mounting Height: Hauteur de montage: Altura de la instalación:

7 – 9 ft (2.1 m – 2.7 m). 4 ft (1.2 m).

20' 6m
Side View / Vue de Cote

11

7'6" 0 (2.3m) 0

7' 2m

13' 4m

20' 6m

27' 8m

35' 11m

PRELIMINARY DRAFT 8/24/09

-1-

5800PIR-RES Wireless Motion Sensor - Installation Instructions
ENROLL THE SENSOR
Enroll the sensor in the control panel prior to its usage in the system. Refer to the control panel instructions for programming details. Program the sensor as an “RF” type (supervised RF) device. To enroll: connect the battery and wait for power up to end (see LED Indications table). When prompted for the serial number, activate the sensor (wave a hand in front of the lens) to enroll the sensor. Loop 1 Pulse count 2; Up to 80 lbs. Animal Immunity

TROUBLESHOOTING
Problem: The system displays a “low battery” message. Solution: Replace the battery within 7 days.

SPECIFICATIONS
Power: Battery* (included). Battery Life, years (typical): RF Frequency: Operating Temperature: (for indoor use environment) Relative Humidity, no condensation: Detectable Walk Rate: Temperature Compensation:
1 x 3 V, Lithium; CR123A / DL 123A / 466 5 345 MHz 14° to 131° F (-10° to 55° C) 95% max. 0.7 – 7ft/Sec. (0.2 – 2.0m/Sec.) Advanced Dual Slope

LED INDICATIONS
Condition Power Up Walk Test Indicator LED Blinks once per second (for < 45 seconds) ON for 3 seconds = Loop 1 / Low Sensitivity Alarm Flickers rapidly for 3 seconds = walk test period ended

MOUNT THE SENSOR (See page 1)
Before mounting the transmitter permanently, conduct Go/No Go tests (see control panel manual) to verify adequate signal strength and reorient or relocate the sensor if necessary. For Animal (Pet) Immunity: • Install the sensor where animals cannot come within 6 ft (1.8 m) of the sensor by climbing on furniture or other objects. • Aim the sensor away from stairways, furniture or other objects that can be climbed on by animals. • Do not use optional swivel mount brackets.

* Battery Caution: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C), or incinerate. Dispose of used batteries promptly. Keep away from children.

APPROVALS / LISTINGS
• • • • • FCC part 15, Class B verified IC, ICES-003, Class B verified C-Tick CE SIA-PIR-01 Passive Infrared detector standard features for false alarm immunity. • cETLus Listed COMPLIANCE NOTES • Product must be tested at least once each year. • Product must be installed within the protected area only.

WALK TESTING
The 10 minute walk test mode begins after power up, and can be restarted by removing and replacing the battery. As you walk through the detection pattern, the sensor LED will light for 3 seconds to indicate each alarm detection. Note: In walk test mode all transmissions will be sent as they occur. During normal operation, only one transmission sequence will occur within a 3-minute period to conserve battery life.

FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: − Reorient or relocate the receiving antenna. − Increase the separation between the equipment and receiver. − Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. − Consult the dealer or an experienced radio/television technician for help.

The user is cautioned that changes or modifications not expressly approved by Honeywell could void the user’s authority to operate this equipment. IC NOTICE: This Class B digital device complies with the Canadian ICES-003. Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS-210 of the IC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à la norme CNR-210 des règles d’IC. L’utilisation de ce dispositif est autorisée seulement aux deux conditions suivantes ; (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

To obtain applicable EU compliance Declaration of Conformity for this product, please refer to our Website, http://www.security.honeywell.com/hsce/international/index.html.
 2009 Honeywell International Inc. Honeywell is a registered trademark of Honeywell International Inc. All other trademarks are the properties of their respective owners. All rights reserved. Assembled in Mexico.

For the latest U.S. warranty information, please go to: www.honeywell.com/security/hsc/resources/wa or Please contact your local authorized Honeywell representative for product warranty information.

Ê800-04182&Š
P/N 800-04182 Rev A 8/09

PRELIMINARY DRAFT 8/24/09

-2-