Honeywell 5816OD Data Sheet

5816OD

OUTDOOR WIRELESS CONTACT/TRANSMITTER

Magnet and batteries included

Honeywell’s robust 5816OD is a weatherproof, waterresistant outdoor wireless transmitter that provides excellent detection and performance in extreme temperatures. It operates in temperatures from -40˚ F to 150˚ F (-40˚ C to +66˚ C), (100% RH). The 5816OD also contains two unique zones. The first loop is a normally closed circuit contact that can have external devices wired directly to it. The second

loop is a built-in magnetic reed switch that can be used to protect gates, sheds, detached garages or any other outdoor area with an exit/entry point. It is also an ideal way to protect outdoor equipment when using outdoor rated magnetic pull apart contacts. With its dark gray housing, the 5816OD blends well with most outdoor surroundings and can be custom-painted* to match its mounting surface.
*Recommended Paints: Krylon® "Fusion for Plastic", Rust-Oleum® "Plastic" and Dupli-Color® "Vinyl & Fabric Coating"
All trademarks are properties of their respective owners

FEATURES
• Weather-proof and water-resistant housing makes it ideal for harsh outdoor climates -40º F to 150º F (-40º C to +66º C), (100% RH) • Maximum magnet gap 1.75" on wood, vinyl and non-metallic surfaces and 1.25" on steel to facilitate easier installation • Two long life AA lithium batteries, easily replaceable • Built-in reed switch contact loop • Built-in wired closed contact loop (for use with external devices) • Tamper protection-removal of front cover and transmitter from mounting plate • Screw mountable • Stainless steel or nylon cable tie mountable (ties not included) • Magnet and magnet spacer included • Paintable plastic housing to match any surface

MOUNTING
COMPONENT IDENTIFICATION

FLAT SURFACES
FENCE POST FENCE GATE MAGNET SPACER MAGNET MOUNTING SCREW (2)

CURVED SURFACES
GATE POST FENCE GATE

SENSOR MOUNTING PLATE SENSOR COVER SCREW

COVER SCREW

SENSOR

BATTERY CHAMBER COVER

SENSOR MOUNTING PLATE

MAGNET

MAGNET SPACER
SENSOR MAGNET SENSING SLIDE

SENSOR MOUNTING PLATE MAGNET

MAGNET SPACER

MOUNTING SCREW (4)

5816OD

OUTDOOR WIRELESS CONTACT/TRANSMITTER

SPECIFICATIONS:
Device Wiring
• Dimensions: - Sensor: 2.01" W x 4.25" H x 1.4" D (51mm x 108mm x 35.6mm high off mounting surface) - Magnet: .89" W x 4.02" H x .92" D (22.5mm x 102mm x 23.27mm) • UL Listings: UL634, UL1023, ULC C1023, ULC-ORD-C634-86 • Moisture Resistance: NEMA 4X rated
SENSOR MOUNTING PLATE SENSOR

CL OS ED (NC CO ) MM ON OP EN (NO )

TO EXTERNAL CONTACT SWITCH

CONNECT WIRES TO TERMINAL BLOCK IN BATTERY CHAMBER

Add Caulking

BACK VIEW

SEALING COVER

• Battery Installation and Replacement
IMPORTANT:

- Change both batteries at the same time. Do not mix weak batteries with new batteries. - Use two (2) lithium 1.5VDC AA cells. Use Eveready’s Energizer® Ultimate LITHIUM AA batteries, Honeywell part number 462. OBSERVE BATTERY POLARITY. Battery Replacement: 1. Remove cover screw and swing Sensor to remove from Sensor Mounting Plate. 2. Use screwdriver in any pivot point and pry Battery Chamber Cover off. Replace batteries. 3. Orient Battery Chamber Cover so the screw hole lines up with the screw hole in the sensor cover, and press to close. 4. Engage Sensor tabs into mating holes in Sensor Mounting Plate and swing closed. Secure with cover screw.
PRY POINTS PRY POINTS

Easy Battery Replacement

TERMINAL BLOCK FOR EXTERNAL CONTACT SWITCH

ADD CAULKING

5816OD-002-V0

ORDERING
5816OD Outdoor Wireless Residential/Commercial Contact/Transmitter

Automated and Control Solutions Honeywell Security & Communications 2 Corporate Center Drive Suite 100 P.O. Box 9040 Melville, NY 11747 www.honeywell.com

L/5816ODD/D October 2011 © 2011 Honeywell International Inc.