Honeywell 5828 and 5828V - User Guide Dated 02/06 Rev. B

K0021V2B 2/06 Rev. B

ADEMCO 5828/5828V

Wireless Bidirectional Fixed-Word Keypads

User Guide

GENERAL INFORMATION
The ADEMCO 5828 and 5828V are wireless keypads
that can be used to operate and get status from you
r
security system. The 5828 and 5828V have the
following features (voice annunciation features app
ly
only to the 5828V):
•

Can be used to arm/disarm, and perform other
system operations.
•

Can display and/or annunciate system status.
•

Can automatically display and/or annunciate a
change in system status if AC powered (e.g., for an

alarm, the keypad will announce the type of alarm
(fire or burglary) and location (e.g. kitchen windo
w).
•

The 5828V Message Center can be used to record
and play back a voice memo to yourself, or leave a
message for a family member.
•

Can be battery- or AC-powered (AC-powered units
have several advantages, described below).
Battery
BatteryBattery
Battery-
--
-Powered Operation:
Powered Operation: Powered Operation:
Powered Operation: When powered by battery,
the keypad must first be activated by pressing any
numbered key. The keypad will display the current
system status within a few seconds. You may at any

time before or after receiving status, arm, disarm,
send
a panic alarm, or perform other system operations.
The
keypad becomes inactive when no keys have been
pressed for 15 seconds, and must be reactivated to
display the current status.
AC
ACAC
AC-
--
-Powered Operation:
Powered Operation: Powered Operation:
Powered Operation: When powered by the optional
AC adapter, the keypad remains active at all times.
If
AC power is lost, the keypad reverts to battery-pow
ered
operation until AC power is restored and a new stat
us
request is made (
Q
key).
NOTE:
NOTE:NOTE:
NOTE: Whether the unit is powered by battery or AC
,
the 5828/5828V may take a few seconds to display
and/or annunciate the new status after pressing the
[
Q
]
key.
5828V-00-006-V0
1
OFF
4
MAX
7
INSTANT
READY
2
AWAY
5
TEST
8
CODE
0
3
STAY
6
BYPASS
9
CHIME
#
MESSAGE
MIC
ARMED
READY
RECORD
VOLUME
PLAY
STATUS
FUNCTION
VOICE
D
C
B
A
5828V
ONLY

5828V Keypad with Front Cover Removed
KEYPAD KEYS
These keypads include 12-operational keys, as well
as
four Special Function keys that are backlit for eas
e of
use when the keypad is active. To access the keypad

keys, simply open the swing-down door by applying
outward pressure on the door release slot on the ri
ght
side.
Panic alarms are activated by pressing the key pair
s
shown in the table below. Special Function keys A,
B,
and C, can be programmed by your installer to provi
de
the same alarms by pressing a single key and holdin
g it
down for 3-seconds, or can be assigned other system

operations. (Check with your installer for the
availability and assignment of these keys).

Key
Pairs
Function

Function
Keys
Function
[1] & [
Q
]



A

[
Q
] & [#]



B

[3] & [#]



C



D

SOUNDER

The keypad’s built-in sounder pulses three times an
d
then pauses (repeatedly) for fire
firefire
fire alarms, and generates
a continuous two-tone sound for burglary
burglaryburglary
burglary and audible
panic alarms
.
HOW TO GET SYSTEM STATUS
When Powered By Battery
When Powered By BatteryWhen Powered By Battery
When Powered By Battery


Pressing any key will turn on the keypad. However,
to
specifically request system status from the control
,
simply press the [
Q
99key. Status will be displayed
within a few seconds.
When Powered By AC Power
When Powered By AC PowerWhen Powered By AC Power
When Powered By AC Power


On AC powered units you can get the status by viewi
ng
the display. The keypad is automatically updated wh
en
a change in system status takes place (arming,
disarming, trouble, etc.).
HOW TO PROGRAM OR CHANGE YOUR 4-DIGIT
SECURITY CODE IF USING QUICK KEY FUNCTIONS
In order to Quick Arm the system using this keypad,

you will need to program your own 4-digit security
code
into the keypad. This code must
mustmust
must match a code that has
already been programmed into your control panel. To

program the 4-digit code, perform the following ste
ps:
1.

Press the 7
77
7
INSTANT
and 9
99
9
CHIME
keys at the
same time until the display flashes double dashes

(- -), then release.
2.

Enter the 4-digit security code that matches a vali
d
user code already programmed into your control
panel. Do NOT
NOTNOT
NOT use the Duress Code. There will be
There will be There will be
There will be
no display of the numbers you pressed.
no display of the numbers you pressed. no display of the numbers you pressed.
no display of the numbers you pressed.
-
2
-
3.

Press
Q

READY
to accept your entry. The keypad
will display the system status.
MEMO/MESSAGE CENTER (5828V only)
Recording and playing back messages
Recording and playing back messagesRecording and playing back messages
Recording and playing back messages


The keystrokes required for message recording and
playback are as shown in the table below.
In this table, read the + sign as “followed by”
Example: # + 1 would be read as the [#] key followe
d by
the [1] key.
MESSAGE CENTER (LYNX)

TO:
PRESS:

Record a message:

# + 1

Stop recording before end of 20 seconds:

1

Playback a message:

# + 3

Adjust message playback volume:

# + 2 + 3
↑
or 6
↓

Mute keypad status announcements:

# + 2 + 1

Restore keypad status announcements:

# + 2 + 3
↑
or 6
↓

MESSAGE CENTER (VISTA)
TO:
PRESS:

Record a message:

# + 0 + 1

Stop recording before end of 20 seconds:

1

Playback a message:

# + 0 + 3

Adjust message playback volume:

# + 0 + 2 + 3
↑
or 6
↓

Mute keypad status announcements:

# + 0 + 2 + 1

Restore keypad status announcements:

# + 0 + 2 + 3
↑
or 6
↓

New message indication:
New message indication:New message indication:
New message indication: If powered by battery, the
Message LED will only
onlyonly
only blink when you activate the
keypad by requesting status. If powered by AC, the

Message LED will blink continuously. Once the
message is played back, the LED will no longer blin
k.
NOTE:
NOTE:NOTE:
NOTE: If using a LYNX control and the word
“MESSAGE” is annunciated at the 5828V keypad, it
means that there is a message waiting at the contro
l
at the control at the control
at the control
panel,
panel, panel,
panel, which can only be retrieved using the LYNX
keypad.
MESSAGE CENTER NOTES
•

Allow any alarm system status annunciation to
complete
completecomplete
complete before starting to record your message.
•

Messages up to 20-seconds long may be recorded and
played back at any time.
•

When messages are first recorded, the red message
LED will continuously flash to show that a new
message is contained in the message center memory.
Once that message is played back, the LED will no
longer flash but the message is retained until a ne
w
message is recorded over it.
•

A status announcement will interrupt the recording
or playback of a message. If this happens, begin
recording or playing the message back again.
If you Mute system status announcements
Mute system status announcements Mute system status announcements
Mute system status announcements for any
reason, you must Restore system status announcement
s
Restore system status announcements Restore system status announcements
Restore system status announcements
by pressing the keys indicated in the “MESSAGE
CENTER” table (above) in order to hear them again.
They will not
not not
not restore on their own.


•

Recording a message or playing back a stored
message is
NOT
affected by muting.
•

If you adjust
If you adjustIf you adjust
If you adjust the volume (3
↑
or 6
↓
) when you play
back a message, and still want system status
announcements to be muted, you must again
againagain
again Mute
system status announcements (# + 2 + 1 for Lynx
panels or # + 0 + 2 + 1 for VISTA panels).
HOW TO REPLACE THE BATTERIES
1.

If the keypad is AC powered, unplug the AC
transformer from the wall outlet.
2.

If the keypad is not wall mounted advance to step 3
.
If the keypad is wall mounted, perform the
following:
Grasp the keypad firmly. Lift straight up (about 1/
4
inch) and out, to separate the keypad from the
mounting plate. This exposes the covered battery
compartment on the backside of the keypad.
3.

Rest the inverted keypad on a non-abrasive surface,

remove the battery compartment cover and remove
the old batteries and properly discard.
4.

Replace the old batteries with 3 AA, 1.5 Volt,
Alkaline batteries (ADEMCO part number 468 or
equivalent). Always replace all three batteries at

once to ensure normal operation of the keypad over
the anticipated battery lifetime. Make sure that
battery positive (+) and negative (–) terminals are

properly oriented with the battery spring clip
connections. Refer to battery placement graphic
below.
batt_case-001-V0
AA BATTERY
AA BATTERY
AA BATTERY

Battery Compartment
5.

Replace the battery cover.
6.

If the keypad is not wall mounted advance to step 7
.
If the keypad is wall mounted, perform the
following:
Reattach the keypad to its mounting plate by
aligning the four mounting holes in the keypad case

back with the four mounting clips on the mounting
plate. Lower the keypad onto the clips.
7.

If the keypad is AC powered, plug the AC
transformer into the wall outlet.
8.

Activate the keypad by pressing any numbered key
until it beeps.
9.

Enter the following twice: your 4-digit security co
de
+ 1
11
1
OFF
, to clear any trouble condition displayed.


- 3 -
GENERAL NOTES
•

If the keypad is on battery power, it will go into
battery-saver mode (become inactive) in 15-seconds
with no key presses, even if exit delay is set to a

longer time period.
You would have to press the [
Q
99key to9view (or hear)
the new status of the security system.
•

When arming in the MAXIMUM mode, the keypad
will indicate “AWAY INSTANT.” When arming in
the INSTANT mode, the keypad will indicate “STAY
INSTANT.”
•

Do NOT
NOTNOT
NOT use the 5828/5828V to put the LYNX into
Speaker Phone mode.
•

There is no audio indication when you turn on or of
f
lights (X10) using the 5828V.
•

An wireless keypad low battery condition is
displayed as, “BAT” and “00” on the 5828/5828V
keypad.
•

Anticipated battery life of the keypad batteries is
1.5
years.
•

Do NOT
NOT NOT
NOT use the 5828V for silent panic operation
because the keypad itself is not silent.

This Honeywell Home security system is designed for
use with devices manufactured or approved by Resid
eo
Technologies, Inc., through its subsidiary Ademco I
nc. (“Resideo”). Your security system is not design
ed for use with any
device that may be attached to your security system
's touchpad or other communicating bus if Resideo h
as not approved
such device for use with your security system. Use
of any such unauthorized device may cause damage or
compromise
the performance of your security system and affect
the validity of your Resideo limited warranty. When
you purchase
devices that have been manufactured or approved by
Resideo you acquire the assurance that these device
s have been
thoroughly tested to ensure optimum performance whe
n used with your security system.

TWO YEAR LIMITED WARRANTY
Resideo Technologies Inc., is the company behind an
d the manufacturer of this product (“Seller”), 2 Co
rporate Center Drive, Melville,
New York 11747 warrants its products to be free fro
m defects in materials and workmanship under normal
use and service, normal
wear and tear excepted, for 24 months from the manu
facture date code; provided, however, that in the e
vent the Buyer presents a
proper invoice relating to the purchased product an
d such invoice bears a date later than the manufact
ure date, then Seller may at its
discretion, reflect the warranty period as commenci
ng at invoice date. Except as required by law, this
Limited Warranty is only made to
Buyer and may not be transferred to any third party
. During the applicable warranty period, Seller wil
l repair or replace, at its sole
option and as the exclusive remedy hereunder, free
of charge, any defective products.
Seller shall have no obligation under this Limited
Warranty or otherwise if the product:
(i) is improperly installed, applied or maintained;

(ii) installed outside of stated operating paramete
rs, altered or improperly serviced or repaired by a
nyone other than the Seller/Seller’s
Authorized Service/Repair Center;
(iii) damage is caused by outside natural occurrenc
es, such as lightning, power surges, fire, floods,
acts of nature, or the like; or
(iv) defects result from unauthorized modification,
misuse, vandalism, alterations of serial numbers,
other causes unrelated to
defective materials or workmanship, or failures rel
ated to batteries of any type used in connection wi
th the products sold
hereunder.
Exceptions to Warranty With Respect to Honeywell Pr
oducts listed below:
Exceptions to Warranty With Respect to Honeywell Pr
oducts listed below:
Exceptions to Warranty With Respect to Honeywell Pr
oducts listed below:
Exceptions to Warranty With Respect to Honeywell Pr
oducts listed below:


Hardwire Contacts and PIRs – Seller warrants parts
for hardwire contacts and PIRs in accordance with t
he terms of the above limited
warranty for a period of five (5) years from the ma
nufacture date code.
EXCLUSION OF WARRANTIES, LIMITATION OF LIABILITY
EXCLUSION OF WARRANTIES, LIMITATION OF LIABILITYEXCLUSION OF WARRANTIES, LIMITATION OF LIABILITY
EXCLUSION OF WARRANTIES, LIMITATION OF LIABILITY


THERE ARE NO WARRANTIES OR CONDITIONS, EXPRESS OR I
MPLIED, OF MERCHANTABILITY, OR FITNESS FOR A
PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYON
D THE DESCRIPTION ON THE FACE HEREOF. TO THE
FULLEST EXTENT PERMITTED BY LAW, IN NO CASE SHALL S
ELLER BE LIABLE TO ANYONE FOR ANY (i)
CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR PU
NITIVE DAMAGES ARISING OUT OF OR RELATING IN ANY
WAY TO THE PRODUCT AND/OR FOR BREACH OF THIS OR ANY
OTHER WARRANTY OR CONDITION, EXPRESS OR
IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATS
OEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY
SELLER’S OWN NEGLIGENCE OR FAULT AND EVEN IF SELLER
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
LOSSES OR DAMAGES. Any product description (whether
in writing or made orally by Seller or Seller’s ag
ents), specifications,
samples, models, bulletin, drawings, diagrams, engi
neering sheets or similar materials used in connect
ion with the Buyer’s order are
for the sole purpose of identifying the Seller’s pr
oducts and shall not be construed as an express war
ranty or condition. Any suggestions
by Seller or Seller’s agents regarding use, applica
tions, or suitability of the products shall not be
construed as an express warranty or
condition unless confirmed to be such in writing by
Seller. Seller does not represent that the product
s it sells may not be compromised
or circumvented; that the products will prevent any
personal injury or property loss by burglary, robb
ery, fire or otherwise, or that the
products will in all cases provide adequate warning
or protection. Buyer understands that a properly i
nstalled and maintained alarm
may only reduce the risk of a burglary, robbery or
fire without warning, but it is not insurance or a
guarantee that such will not occur
or will not cause or lead to personal injury or pro
perty loss. CONSEQUENTLY, SELLER SHALL HAVE NO LIAB
ILITY FOR ANY
PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASE
D ON ANY CLAIM AT ALL INCLUDING A CLAIM THE
PRODUCT FAILED TO GIVE WARNING. However, if Seller
is held liable whether directly or indirectly for a
ny loss or damage with
respect to the products it sells, regardless of cau
se or origin, its maximum liability shall not in an
y case exceed the purchase price of the
product, which shall be fixed as liquidated damages
and not as a penalty, and shall be the complete an
d exclusive remedy against the
Seller. Should your product become defective during
the warranty, please contact your installer to fac
ilitate repair or replacement with
Seller pursuant to the terms hereof. Seller reserve
s the right to replace any defective product under
warranty with new, refurbished, or
remanufactured product.

FEDERAL COMMUNICATIONS COMMISSION STATEMENTS
The user shall not make any changes or modification
s to the equipment unless authorized by the Install
ation Instructions or User's Manual.
Unauthorized changes or modifications could void th
e user's authority to operate the equipment.
FCC CLASS B STATEMENT
This equipment has been tested to FCC requirements
and has been found acceptable for use. The FCC requ
ires the following statement for
your information:
This equipment generates and uses radio frequency e
nergy and if not installed and used properly, that
is, in strict accordance with the
manufacturer's instructions, may cause interference
to radio and television reception. It has been typ
e tested and found to comply with the
limits for a Class B computing device in accordance
with the specifications in Part 15 of FCC Rules, w
hich are designed to provide
reasonable protection against such interference in
a residential installation. However, there is no gu
arantee that interference will not occur in
a particular installation. If this equipment does c
ause interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
• If using an indoor antenna, have a quality outdoo
r antenna installed.
• Reorient the receiving antenna until interference
is reduced or eliminated.
• Move the radio or television receiver away from t
he receiver/control.
• Move the antenna leads away from any wire runs to
the receiver/control.
• Plug the receiver/control into a different outlet
so that it and the radio or television receiver ar
e on different branch circuits.
• Consult the dealer or an experienced radio/TV tec
hnician for help.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadi
an ICES-003.
Cet appareil numérique de la classe B est conforme
à la norme NMB-003 du Canada.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules,
and RSS 210 of IC. Operation is subject to the fol
lowing two conditions: (1) This device
may not cause harmful interference (2) This device
must accept any interference received, including in
terference that may cause undesired
operation.
Cet appareil est conforme à la partie 15 des règles
de la FCC & de RSS 210 des Industries Canada. Son
fonctionnement est soumis aux
conditions suivantes: (1) Cet appareil ne doit pas
causer d' interferences nuisibles. (2) Cet appareil
doit accepter toute interference reçue y
compris les interferences causant une reception ind
ésirable.


















The product should not be disposed of with other ho
usehold waste. Check for the nearest authorized col
lection centers or authorized recyclers. The
correct disposal of end-of-life equipment will help
prevent potential negative consequences for the en
vironment and human health.
The Honeywell Home Trademark is used under license
from Honeywell International Inc. This product is m
anufactured by Resideo Technologies, Inc.



2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
© 2020 Resideo Technologies, Inc.
www.resideo.com

ÊK0021V2BlŠ
K0021V2B 2/06 Rev. B