Honeywell Home PROSIXFLOOD Installation Instructions - Dated 2/19 Rev. C

PROSiXFLOOD

Wireless
Flood

Sensor



Installation
and Setup Guide


The
PROSiXFLOOD

is a wireless flood sensor with
external probe (FP280) intended for use with Honeywell
Home
controls that support
PRO
SiX™ series devices.
When the probe contacts water, the sensor sends an
alarm or trouble signal
to the controller depending on
zone type selected (ex. trouble
= Monitor Zone; alarm
=
24hr Aux)
within 15 seconds*
. The probe is supervised
for an open circuit (cut wire) and sends a trouble signal
up to 15
seconds
after the condition is sensed. The
sensor also has a front cover tamper and wall tamper
switch.

* See Controller’s instructions for setting alarm delay
options, if available.


MOUNT THE PROSIXFLOOD

1. Open the case
- firmly s
lide the front
and
back

housings in opposite directions and
pull
them apart.



2. Mount the
PROSiXFLOOD
to a wall as shown,
using
the double sided tape and screws provided.

3. Connect the flood probe’s wires to the
PROSiXFLOOD
terminals.

4. Mount the flood probe in the area where flood
notification is desired.
Secure probe with #6 x ¾” pan
head screw provided.

5. Reattach front cover and s
ecure with the #2
x 1/4”
screw
provided
.
After enrolling
and before mounting, verify adequate
signal strength by conducting a sensor test
(see
controller’s instructions) with the devic
e in its intended
mounting location. Adjust the device location and
orientation as necessary.



A
= Terminal Blo
ck for sensor

B
= Tamper S
witch

C
= LED

Probe:
FP280



2

ENROLL AND SETUP

Set
the
control
in Programming Mode
and when
prompted:

1. Pull
the ba
ttery tab
to activate the
PROSiXFLOOD
.
(Use the tamper switch
if the battery tab is removed.)

2. The LED flashes (
up to about 20 seconds*) during
enrollment.

•
The device sends its unique MAC ID (Serial
Number); t
he control
ler registers the device and
displ
ays
the transmitter data on screen
.
*NOTE
:
Enrollment time varies depending on the

signal strength between the device and the

controller.

3. When
done,
the LED is ON for 3 seconds and the
control beeps
to confirm
enrollment.

NOTE
: If the device is not s
ucc
essf
ully enrolled
during the enrollment period, the LED turns off
and the device powers down. Activate the
tamper
switch to restart the enrollment
process.





IMPORTANT
: Once enrolled in a system, the
PROSiXFLOOD
cannot be used with another controller

until
it is removed from the current controller. See the
Controller’s instructions for details.

TESTING
NOTE
: After enrollment, the unit can be tested
by placing the probe in a cup of water. The control sh
ould
indicate a fault condition after 15 seconds.

24-
HOUR ENROLLMENT DELETION AND
DEFAULT

If the device is enrolled in a panel different than the
intended panel, and you are unable to delete it from
the unintended panel, reset
the device
to factory
default setting:

1. Open the cover
and remove the battery.

2. Hol
d do
wn the tamper switch while reinserting the
battery.
Rapid LED flashing indicates successful
deletion (LED flashes as if in enrollment mode). If
LED does not flash, delete was not successful.

3. Reattach the cover.


This procedure is available for 24 hours
aft
er
enrollment with a panel and the device remains
powered (battery installed).


3
LED INDICATIONS


LED

Status



Rapid Flashes for

about 20 seconds, then

ON for 3 seconds

Power Up –
Enrollment


Slow Flashes

Power Up –
Device enrolled;
front
Co
ver
Tam
per activated. To stop
flashes,
clear the tamper condition
by
reattaching the cover
. It also
times
out after 10 minutes.


ON

(while in Programming Mode)

Sensor LED toggles on and off when the sensor is selecte
d. See Sensor
Location Feature.

BAT
TERY RE
PLACEMENT

•
Push the bottom latch of the mounting
bracket back to disengage
it. Then
slide
the back housing, up and out to remove
it from the
mounting
bracket
.

•
Slide the front and back housings in
opposite directions
and pu
ll the housings
apart
.
•
Remo
ve
the battery
,
wait
10 seconds
,

then insert a new battery
.
Recommended batteries:

Resideo 466

Duracell DL123A


Huiderui CR123A


Panasonic CR123A

•
Place the front and back housings
together and slide them together as
shown.

BATTERY CAUTION
: Risk of fir
e, explosion
and burns. Do not recharge, disassemble, heat
above 212°
F (100°
C)
or incinerate. Dispose of
used batteries proper
ly. Keep away from
children.

NOTE
: Constant exposure to high or low
temperature or high humidity may reduce
battery
life.



WARN
ING
: Use
only b
atteries specified in marking. Use of a different battery
may have a detrimental effect on product operation.


SPECIFICATIONS:

Battery:
..................................
1 x 3V Lithium, Resideo
466,
Panasonic CR123A,

Duracell DL123A or Huiderui CR123A

Tamper:
...............................................................................
Front

Co
ver and
Wall

RF Frequency
:
...........................................................................................
2.4GHz

Operating Temperature
: ................................................32°
– 122° F / 0°
– 50° C

(Agency Compliance 32°
– 120° F / 0°
– 49° C)

Relative Humidity:
.........................
95% max. (Agency Compliance -
93% max.),

non-
condensing

Dimensions:
.......
1” H x 3.13” L x 1.61” W / 25.
5 mm H x 79.5 mm L x 41 mm
W

APPROVAL LISTINGS:

FCC / IC

cETLus Listed

Conforms to ANSI/
UL
2017

Certified to CAN/CSA STD C22.2
#205

Other Standards:

RoHS


Product must be tested at

least once each year





FEDERAL COMMUNICATIONS COMMISSION &
ISED
ST
ATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's
authority to operate the equipment.

CLAS
S B DIGI
TAL DEVICE STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following stat
ement for your information: This equipment generates and uses radio
frequency energy and if not insta
lled and
used properly, that
is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested
and found to comply with the limits for a Class B computing device in accordance w
ith the
specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such
interference in a residential installation. However, there is no guarantee that interference will not occur in a particular i
nstallation. If th
is equipment does cause interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:

•

If using an indoor ant
enna,
replace it with a qual
ity outdoor antenna.

•

Reorient the receiving antenna until interference is reduced or eliminated.

•

Move the radio or television receiver away from the receiver/control.

•

Move the antenna leads away from any wire runs to the receive
r/contro
l.
•

Plug the receiver
/control into a different outlet so that it and the radio or television receiver are on different branch circuits.

•

Consult the dealer or an experienced radio/TV technician for help.

ISED
CLASS B STATEMENT

This Class B digital ap
paratus
complies with Canadi
an ICES
-003.

Cet appareil numérique de la classe B est conforme à la norme NMB
-003 du Canada.

FCC / I
SED
STATEMENT

This device complies with Part 15 of the FCC Rules, and I
SED
’s license
-exempt
RSS
s. Operation is subject to the f
ollowing
two conditions: (1)
This device may not cause harmful interference, and (2)
This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC
et exem
pt de licence RSS d’
ISED
. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer
d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une r
écepti
on indés
irable.


Responsible
Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Drive.,
Melville, NY 11747, Ph: 516-
577-
2000


RF EXPOSURE

Warning
– The antenna(s) used for thi
s device
must be installed t
o provide a separation distance of at least 7.8 inches (20 cm) from all
persons and must not be co-
located or operating in conjunction with any other antenna or transmitter except in accordance with FCC
and ISED
multi
-transmitte
r produc
t procedures.

Mise en Garde

Exposition aux Fréquences

Radio
:
La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de
séparation d'au moins 20 cm (7,8 pouces) de toute personne et ne pas être située(s) ni fo
nctionner parallèlement à tout autre
transmetteur ou antenne, excepté en conformité avec les procédures de produit multi transmetteur FCC et ISED
.

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, F
OR

DETAILS REGARDING
LIMITAT
IONS OF THE ENTIRE ALARM SYSTEM.






Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Drive.,
Melville, NY 11747, Ph: 516-
577-
2000


The product should not
be dis
posed of with other
household waste. Check for the nearest authorized collection centers or authorized recyclers. The
correct disposal of end-
of-life equipment will help prevent potential negative consequences for the environment and human health.

Any atte
mpt to reverse-
engineer this device by decoding proprietary protocols, de-
compiling firmware, or any similar actions is strictly prohibited.


SUPPOR
T & WARRANTY INFORMATION

For the latest documentation
and
support, please go to:

www.resideo.com


For the latest warranty information, please go to:

www.security.honeywellhome.com/warranty


The Honeywell Home Trademark is used under l
icense from Honeyw
ell Inte
rnational Inc.

Th
is product is manufactured by Resideo
Technologies
, Inc.
and its affiliates.




2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

©
20
20
Resideo Technologies, Inc.

www.resideo.com






Ê800
-
2
5245CaŠ

PROSiXFLOOD


800
-
2
5245
C

2/
19

Re
v

C