Honeywell Home PROWIFI - Install Guide - Dated 08/20 Rev. B

1


PROWIFI


Wireless
Communication Module




Installation and Setup Guide

General Information

The
PROWIFI
Wireless
Communication Module provides
PRO Series Control Panel
s with a Wi
-Fi

connection
and permits t
hem
to
communicate with the
Central Station
and PRO
Series
Wireless
Touchscreens
via
Wi
-Fi . The module connects directly to the Control
Panel and is powered via the Control Panel’s connection.
Refer
to the applicable
Control Panel's Installation and Setup Guide for
additional information.

Installing
the Module
in the PROA7 Series Control Panel


Ensure that all electrical power is removed from the control before installing the module. Unplug the
power supply and disconnect the backup battery.

1.
Affix the provided FCC/IC label (P/N R
800-
26437A
for the PROWIFI
) on the control’s
case back
(refer to Figure 1).

2.
If the Control Panel is not powered
up
proceed to step 7. If the Control Panel is
powered up, disarm the system and wait 30-
60 seconds:

3.
Unplug the power supply.

4.
Remove the screw securing the control t
o the
wall or desk mount.

5.
Remove t
he control from the wall or desk
mount.

6.
Discon
nect the battery
.
QS-162-V0

Figure 1. FCC/IC Label Location


7.
Remove the left side
cover
from the control.

8.
Insert the PROWIFI
module into the slot on
the left side of the control as shown in Figure
2 and ensure the rec
eptacle is securely
seated on the control’s
edge connector.

9.
Secure with the screw.

10.
Install the left side cover.

11.
Connect the battery.

12.
Install the control on the wall or desk mount.

13.
Plug the power supply into a 24-hour,
110V
AC unswitched outlet.


QS-058-V1
COVER
PROWIFI
MODULE
SCREW

Figure 2.
Installing the PROWIFI
Module



Programming

Note:
The
PROWIFI
requires a router and internet service for Wi
-Fi connection.

1.
Programming associated with the PROWIFI
module
is conducted
through
the AlarmNet 360™ Programmi
ng T
ool. On a laptop, PC or
Smart
De
vice, go to
www.alarmnet360.com
.
2.
When programming is complete, perform a Communications Test.
Specifications

Board Dimensi
ons:
...............................................................................................................................................
1.625” W x 2.625” L x 0.3125” D

Input Voltage Range:
..............................................................................................................................................................
3.6
– 14V, Max 17V

Input Voltage:
..................................................................................................................................................................................................
3.5V

Current Drain:
.............................................................................................................................................................................................
250mA

Temperatu
re: ...............................................................................................................................................................
32°F (0°C) to 140°F (60°C)



REFER TO THE INSTALLATIO
N AND SETUP GUIDE FOR THE CONTROL WITH WHICH THIS DEVICE IS USED FOR WARRANTY
INFORMATION AND LIMITATIONS OF THE ENTIRE SYSTEM.



FEDERAL COMMUNICATIONS COMMISSION
& ISED
STATEMENTS
The user shall no
t make any changes or modifications to the equipment unl
ess authorized by the Installation Instructions or User's Manual. Unauthorized changes or
modifications could void the user's authority to operate the equipment.

FC
C CLASS B STATEMENT

This equipment
has been tested to FCC requirements and has been found ac
ceptable for use. The FCC requires the following statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict acc
ordance with the manufacturer's instructions, may cause
interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B com
puting device in accordance with the specifications in
Part 15 of FCC Rul
es, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that
interference will not occur in a particular installation. If this equipme
nt does cause interference to radi
o or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• If using an indoor antenna, repl
ace it with a quality outdoor antenn
a.
• Reorient the receiving antenna until interference i
s reduced or eliminated.

• Move the radio or television receiver away from the receiver/control.

• Move the antenna leads away from any wire runs to the receiver/control.

• Plug the receiver/control
into a different outlet so that it and the radio or telev
ision receiver are on different branch circuits.

• Consult the dealer or an experienced radio/TV technician for help.

Responsible Party / Issuer of Supplier’s Decla
ration of Conformity: Ademco Inc.,
a subsidiary of Resideo Technologies, Inc., 2 Corporate C
enter Dr., Melville, NY 11747
, Ph:
516
-577
-2000.

ISED
CLASS B STATEMENT

This Class B digital apparatus complies with Canadian ICES
-003.

Cet appareil numérique de la
classe B est conforme à la norme NM
B-003 du Canada.

FCC / I
SED
STATEMENT

This device compli
es with Part 15 of the FCC Rules, and ISED’s
license
-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause
harmful interf
erence (2) This device must accept
any interference received, including interference that may cause undesired operation.


Cet appareil est conforme à la partie 15 des r
ègles de la FCC et exempt de licence RSS
d’ISED
. Son fonctionnement est soumis aux condi
tions suivantes: (1) Cet appareil
ne

doit pas causer
d’interférences
nuisibles. (2) Cet appareil doit accepter toute interférence
reçue y compris les interférences
causant une réception
indésirable
.


RF Exposure Warning

The antenna(s) used for this trans
mitter must be installed to provide
a separation distance of at least 7.8 inches (20 cm) from all persons and
must not be co-
located or operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi
-
transmitter
product procedures.

Mise en Garde

Ex
position aux Frequences Radio: La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent
être
installée(s)
à une distance de séparation
d'au moins
20 cm (7,8 pouces) de toute personne et ne pas être située(s) ni fonct
ionner parallèlement à tout autre
transmetteur ou antenne,
excepté en conformité avec les pr
océdures de produit multi transmetteur FCC et ISED
s.

The product should not be disposed of with other household waste. Check for the nearest authorized collection
centers or authorized
recyclers.
Th
e correct disposal
of end-
of -life equipment will help prevent potential negative consequences for the environment and human health.

Any attempt to reverse
-engineer this device by decoding proprietary protocols, de-
compil
ing firmware, or any similar actions
is strictly prohibited.



SUPPOR
T & WARRANTY INFORMATION
For the latest documentation
and
support, please go to:

www.resideo.com


For the latest warranty information, please go to:

www.security.honeywellhome.com/warranty










www.resideo.com

Resideo Technologies, Inc

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

© 2021
Resideo Technologies, Inc. All rights reserved.
The Honeywell Home trademark is used under license from Honeywell
International, Inc.
This product is manufactured by Resideo Technologies, Inc. and its affiliates.
ÊR800
-26317B%Š

R800
-
26317
B


8
/
20

Rev.
B