Honeywell L7000 User Guide
Related Products
Related Categories
Document Transcript
LYNX Touch
L7000 Series
Security System
User Guide
800-16084 12/13 Rev. A
LYNX Touch L7000 Series
Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell for use
with your security system. Your Honeywell security system is not designed for use with any device that may be
attached to your security system's control or other communicating bus if Honeywell has not approved such device for
use with your security system. Use of any such unauthorized device may cause damage or compromise the
performance of your security system and affect the validity of your Honeywell limited warranty. When you purchase
devices that have been manufactured or approved by Honeywell, you acquire the assurance that these devices have
been thoroughly tested to ensure optimum performance when used with your Honeywell security system.
–2–
TABLE OF CONTENTS
SYSTEM OVERVIEW ................................................................................................................................................. 5
Features ................................................................................................................................................................... 5
General Operation ................................................................................................................................................... 7
Quick View of System Functions ............................................................................................................................ 8
About the Touch screen Control ........................................................................................................................... 10
About the Display and Indicators ........................................................................................................................ 11
Navigating Menus ................................................................................................................................................. 13
SECURING THE PREMISES ................................................................................................................................. 16
System Status ........................................................................................................................................................ 16
Arming the System................................................................................................................................................ 17
Entry/Exit Delays .................................................................................................................................................. 24
Disarming the System........................................................................................................................................... 26
Bypassing Protection Zones .................................................................................................................................. 28
Panic Keys ............................................................................................................................................................. 30
Chime Mode ........................................................................................................................................................... 31
Voice Mode ............................................................................................................................................................. 32
USER FUNCTIONS .................................................................................................................................................. 33
User Access ............................................................................................................................................................ 33
View Events ........................................................................................................................................................... 37
Message Recording and Playback ........................................................................................................................ 38
System Settings ..................................................................................................................................................... 40
Clock/Calendar ...................................................................................................................................................... 41
Automation ............................................................................................................................................................ 44
Reminders .............................................................................................................................................................. 51
WiFi Configuration................................................................................................................................................ 54
Video Camera Control Feature ............................................................................................................................ 57
Two Way Voice Feature (Alarm Audio Verification) ........................................................................................... 60
Remote Services..................................................................................................................................................... 61
Slide Show.............................................................................................................................................................. 62
SUMMARY OF AUDIBLE & VISUAL NOTIFICATIONS ................................................................................. 63
Audible Soundings................................................................................................................................................. 63
System Displays .................................................................................................................................................... 64
SYSTEM FUNCTIONS ............................................................................................................................................. 65
Testing the System ................................................................................................................................................ 65
Maintaining Your System ..................................................................................................................................... 67
FIRE/CO ALARM SYSTEM ..................................................................................................................................... 69
General Information.............................................................................................................................................. 69
National Fire Protection Association’s Smoke Detector Recommendations ..................................................... 70
Emergency Evacuation ......................................................................................................................................... 71
REGULATORY AGENCY STATEMENTS ............................................................................................................ 72
LIMITATIONS OF THIS ALARM SYSTEM ......................................................................................................... 73
SERVICING INFORMATION ................................................................................................................................. 74
OWNER’S INSURANCE PREMIUM CREDIT REQUEST ................................................................................ 75
INDEX .......................................................................................................................................................................... 77
TWO YEAR LIMITED WARRANTY ...................................................................................................................... 79
Congratulations on your ownership of a Honeywell Security System. You have made a wise decision in
choosing it, for it represents the latest in security protection technology today. Honeywell is the world's
largest manufacturer of security systems and millions of premises are protected by Honeywell products.
–3–
–4–
SYSTEM OVERVIEW
Features
General Information
This system offers you three forms of protection: burglary, fire, and emergency, depending on the configuration
of your system. The system consists of a touch screen control for system operation, various wireless sensors that
provide perimeter and interior burglary protection, and optional smoke or combustion detectors to provide early
fire warning. In addition, optional wireless keypads or key fobs may have been installed to allow you to control
the system away from the touch screen control.
The system monitors protection zones and system status, displays appropriate information on the touch screen
display, and initiates appropriate alarms. Your system may also have been programmed to automatically send
alarm or status messages over the phone lines or via the cellular/GSM network or the internet to a central
alarm monitoring station, and may also be capable of two-way voice communication with the central station.
IMPORTANT SECURITY NOTICE
Your key fob is similar to your keys or access card. If lost or stolen, another person can compromise your security system.
Immediately notify your Dealer/Installer of a lost or stolen key fob. The Dealer/Installer will then remove the key fob programming
from the security system.
The user features of this security system are listed below. Ask your installer which features have been
programmed for your system.
• Stay and Away arming modes: By using these modes you can protect either the perimeter only, or the
entire premises.
• Panic key functions: A designated key allow you to manually activate fire, medical emergency, or silent
police alarms. Refer to the Panic Keys section for detailed information.
• Follow me reminder announcements: Allows the panel to dial a number that you have specified, at a
programmed day/time and deliver a message programmed by your installer.
• Real-time clock: Touch screen displays current date and time. Refer to the Clock/Calendar section for
procedures for setting the time.
• Message center: The system allows recording and play back of brief voice messages. Refer to the
Recording/Playback Messages section for procedures.
• Two-way voice: Allows the central station to listen, talk to or conduct two-way conversations with
individuals on the premises
• Security Codes: The system is capable of supporting an Installer code, Master user code and 46 additional
User codes including Guest and Duress codes. Refer to the User Access section for detailed information.
• Device activation: Allows you to send “Follow-Me” or e-mail messages, as a result of a system event such as
an alarm or trouble condition. Refer to the Automation section for detailed information.
• Schedules feature: Allows you to schedule the automatic activation or deactivation of program events (e.g.
alarm clock, reminder, and latch key). Refer to the Automation section for detailed information.
• Text Message center (Requires TotalConnect Service): The system allows you to send and receive text
messages.
• Web content (Requires TotalConnect Service): The system allows you to view and display web content
including Weather, News and Traffic reports.
• Video Camera Control: (Requires a WiFi communications device and a router) The system supports up to
20 video cameras and allows selection, control and viewing of video from up to four cameras.
Zones
• Your system's sensing devices have been assigned to various "zones." For example, the sensing device on
your entry/exit door may have been assigned to zone 01, sensing devices on windows in the master bedroom
to zone 02, and so on. These numbers appear on the display when an alarm or trouble condition occurs.
–5–
SYSTEM OVERVIEW
Features
Fire Protection
The fire protection portion of your security system (if used) is always active and will sound an alarm if a fire
condition is detected. Refer to the Fire Alarm System section for important information concerning fire
protection, smoke detectors and planning emergency exit routes from the premises.
Carbon Monoxide
The carbon monoxide (CO) portion of your security system (if used) is always active and will sound an alarm if a
CO condition is detected. Refer to the Fire Alarm System section for more information.
Burglary Protection
Your system provides two modes of burglary protection: STAY and AWAY. STAY mode protects the perimeter
only, allowing you to freely move inside the premises. AWAY mode protects the entire system. Both modes
provide an entry delay time that allows you to reenter the premises without setting off an alarm. For additional
security, you can turn the entry delay off when arming the system. Refer to the Arming the System section. The
system also allows you to bypass selected zones before arming the system, if desired. Refer to the Bypassing
Protection Zones section. The system also provides a Chime mode, for alerting users to the opening of protected
doors and windows while the system is disarmed.
You must arm the burglary protection portion of your system before it will sense burglary alarms. Refer to the
Arming the System section for detailed procedures and information.
Security Codes
At the time of installation, you were asked to provide a personal 4-digit security or “Master User” code. You
must enter the user code when arming and disarming the system, and when performing other system functions.
As an additional security feature, other users who do not need to know your code can be assigned up to 48
different security codes. Refer to the Security Codes section for procedures on adding security codes to the
system.
Alarms
When an alarm occurs, the LYNX Touch internal sounder will sound for about 15-seconds, and the touch screen
displays the zone(s) causing the alarm. After 15-seconds, the internal sounder stops temporarily and voice
announcements of the zones in alarm begins. When these zones have been announced, the internal sounder
sounds again and the cycle repeats itself, until the system is disarmed or until alarm bell timeout occurs. If
your system is connected to a central monitoring station, an alarm message will be sent. To stop the alarm
sounding, simply disarm the system. The zone(s) causing the alarm remain displayed indicating memory of
alarm. Refer to the Disarming the System section for information about clearing the memory of alarm display
Important Note
If your system is equipped to report alarms over the internet via a WiFi Communications module, your router must
remain powered-on at all times. Ask your Installer about this feature for additional information
Two-Way Voice Feature
The control supports voice dialog between an operator at the central station and an individual at the premises.
This feature allows the central station to listen, talk to or conduct a two-way conversation with an individual(s)
at the premises and allows the operator to gather information about the nature and location of the alarm that
may be helpful in responding to police or rescue departments.
–6–
SYSTEM OVERVIEW
General Operation
LYNX Touch False Alarm Prevention Features
Many false alarms are caused by simple accidents, like forgetting to close a door when you leave. The LYNX Touch may
include several features that help prevent false alarms and some of these are optional or programmable. Although turning
off some of these features may provide additional security, it may also increase the chance of false alarms. Your installer can
help you decide whether to use the features or not. The following provides a brief explanation of the features included with
your security system that help prevent false alarms from occurring, and what you should do if such alarms occur.
• Exit/Entry Delays: Your security system has been programmed with delay times that allow you to exit the premises
after arming, and to disarm the system upon entry, before an alarm occurs. If you leave the premises too late when
exiting, or disarm too late when arriving home, it will cause a false alarm. If an alarm occurs, you should disarm the
system immediately, and wait for your monitoring company to call you.
• Exit Alarms: Leaving the premises and forgetting to close the door is a common cause of false alarms. The security
system will sound an alarm, and display “Exit Error”. The security system provides extra time for you to disarm the
system before dialing your monitoring company. Disarming the system immediately may prevent a call to your
monitoring company.
• Exit Time Restart-Exit Delay Restart/Reset: If you leave the premises and enter again before the exit delay has
expired, the system will restart the exit time giving you more time to leave. If there are less than 10 seconds left to exit,
the system will sound fast beeps, indicating an alarm will occur soon if you fail to exit or disarm immediately. If this
occurs, disarm the system and arm it again when you are ready to leave. The Exit Delay can also be restarted by pressing
the RESTART Icon.
• Auto Stay Feature: If you arm the system in the “AWAY” mode from the control’s keypad or an RF keypad but no one
exits, the alarm system will automatically change to the “STAY” mode. This will prevent you from tripping alarms by
remaining on premises. Disarm the system and arm away again when you are ready to leave.
• Alarm Reporting Delay: Your security system has a delay between the time a burglary alarm sounds, and the time the
monitoring company is called. This delay gives you time to disarm the security system before the alarm is reported to the
monitoring company. This delay is factory preset at 30 seconds, but may be increased or decreased by your installer.
• False Alarms: If a burglary or fire alarm condition occurs and the system has been disarmed, the keypad will display
“Alarm Cancelled”. If this was a false alarm, wait for the monitoring company to call you. They will verify your security
code or password and prevent them from calling emergency personnel to respond to a false alarm.
–7–
SYSTEM OVERVIEW
Quick View of System Functions
Function
Press these Keys or Icons
SECURITY FUNCTIONS
Check system status .................................................................... :
System
+ Code
Arm in STAY mode....................................................................... :
Arm Stay
Arm in Night STAY ...................................................................... :
Select Arm Night + Code
Arm Stay
+ Code
Arm in AWAY mode ..................................................................... :
Arm Away
Select Silent Exit + Code
Arm in AWAY mode with Silent Exit ............................................. :
Arm Away
Restart exit delay.......................................................................... :
Restart
OR
Arm if Quick Arm is active* ........................................................... :
+ Quick Arm button
Arm Away
Arm Stay
* User code is not required if Quick Arm is active
+ Code
Disarm system and silence alarms ............................................... :
Disarm
Note: During Entry Delay or when an Alarm Condition exists, the LYNX Touch can be disarmed by entering the User Code. Entering the OFF key is not
required
Arm Instant ................................................................................... :
Set “Delay” tab to “Instant” then Arm STAY or AWAY
Bypass a zone(s).......................................................................... :
Zones
SYSTEM SETTINGS
Adjust Volume, Contrast or Brightness......................................... :
Settings
+ Voice
Restore/unmute user announcements ......................................... :
Settings
+ Chime
Turn Chime mode On or Off ......................................................... :
Settings
+
Clean Touchscreen ...................................................................... :
Settings
MESSAGE CENTER
Record a message ....................................................................... :
Message
Play or Delete a message ............................................................ :
Message
–8–
Clean
SYSTEM OVERVIEW
Quick View of System Functions
Function
Press these Keys or Icons
OTHER FUNCTIONS (accessible from the Master User Screen)
+ Master Code
Tools
Set the time and date................................................................... :
Date Time
Add, delete or change a User Code* ........................................... :
Users
* Only the Master Code can be used to add/delete a User
+ Applicable Test icon
Perform Tests .............................................................................. :
Test
View System Events .................................................................... :
Events
Program, edit or delete Reminders ............................................. :
Reminders
HOME AUTOMATION (If equipped)
+
Operate Garage Door ............................................. :
Automation
Switches
OR
68
+
Manually operate Z-Wave Devices ......................... :
Thermostats
OR
Automation
Locks
OR
Water Valves
Scenes
OR
Schedules
+
Set Scenes, Schedules or Rules OR Run Scenes.. :
Automation
OR
Rules
–9–
SYSTEM OVERVIEW
About the Touch Screen Control
General
**IMPORTANT**
If the LYNX Touch is beeping rapidly upon entering the premises, an alarm has occurred during your absence
and an intruder may still be on the premises. LEAVE IMMEDIATELY and CONTACT THE POLICE from a
nearby safe location.
The touch screen icons and keys allow you to control all system functions. Additionally, the touch screen display
shows the zone and description of all system occurrences.
The system also features a built-in sounder, which will sound during alarms and troubles and a built-in speaker
announces system status. Additionally, the system "beeps" during certain system functions, such as during
entry/exit delay times, in Chime mode, and when depressing any of the keys (to acknowledge the key press).
The voice announcement volume is adjustable. The “beeps” that sound in response to alarms always sound at
the maximum volume level however, the volume level for all other “beeps” (trouble, chime, exit/entry, etc) can
be adjusted.
5
1
4
3
2
7000-100-001-V0
Index
Item
Description
1
Speaker
Source of audible internal warning and confirmation sounds, status announcements, as well as alarms
(see "Summary of Audible Notifications").
2
Home key
Used to exit from a screen or return to the Home Screen. Internal LED indicates the following:
Green = System is ready to be armed
Red = System is armed
Green Blinking = System is disarmed, and not ready to be armed (a fault or alarm exists)
Red Steady = System is Armed
Red Blinking = System is in Alarm
Red/Green Blinking alternately = System programming mode OR Two-way voice mode is active
3
Panic key
When depressed for 4 seconds, the virtual panic icons are displayed on the touch screen. Internal Red
LED is lit in normal conditions
4
Microphone
Used to record personal messages via the Message Center, and for Two-way Voice operation.
5
Display
Window
Color Liquid Crystal Display (LCD) Touch screen. Displays system status icons, time, system status
information, user menus and the virtual keypad.
– 10 –
SYSTEM
SYSTEM OVERVIEW
About the Display and Indicators
Display Definitions
ICON
TEXT
DEFINITION
Ready to Arm
Displayed along with the the text “Ready To Arm” when system is Disarmed and
ready to arm.
Armed Away
“Armed Away” is displayed along the top of the screen. An armed away icon
along with “Armed Away” is displayed after the exit delay expires.
Armed Stay
“Armed Stay” is displayed along the top of the screen. An armed stay icon along
with “Armed Stay” is displayed after the exit delay expires.
Exit Now
28 Seconds
“Armed Stay – Exit Now” or “Armed Away – Exit Now” is displayed in a red
status bar along the top of the screen. An exit icon along with “Exit Now” and the
time remaining (i.e.; “28 Seconds”) is displayed during the exit delay.
Alarm
“Alarm” is displayed in a red status bar along the top of the screen. An alarm
(bell) icon along with “Alarm” is displayed alternately with the Zone that has
caused the alarm.
Fault (Zone
No.&
Description)
“Not Ready To Arm – Fault” is displayed in a yellow status bar along the top of
the screen. An open windowor door icon along with the zone descriptor and
“Window” or “Door” is displayed when a window or entry/exit fault has been
detected.
OR
Displayed alternately with the alarm (bell) icon and “Alarm”.
“Alarm” is also displayed in a red status bar along the top of the screen.
Fire OR
Fire Alarm
95 Fire
The fire icon is displayed with alternating text “Fire” and “Fire Alarm 95 Fire”.
“Fire Alarm” is also displayed in a red status bar along the top of the screen.
Alarm 96
Medical
The Medical icon displayed when a medical alarm is activated. “Alarm” is also
displayed in a red status bar along the top of the screen. (If programmed for
display by your installer)
Alarm 99
Police
The alarm (bell) icon when a burglary alarm is activated. “Alarm” is also
displayed in a red status bar along the top of the screen. (If programmed for
display by your installer) No display if 24 Hour Silent Response Type has been
programmed.
Displayed alternately with Carbon Monoxide when a CO alarm is activated.
“CO Alarm” is also displayed in a red status bar along the top of the screen.
OR
CO Alarm
Cover
Tamper
Reporter
Failure
A check system icon along with “Cover Tamper” is displayed when a cover
tamper has been detected. “Ready To Arm – System Trouble” is displayed in a
yellow status bar along the top of the screen.
The system has identified a problem with the telephone dialer.
– 11 –
SYSTEM OVERVIEW
About the Display and Indicators
ICON
TEXT
Low Battery
90 RF Jam
DEFINITION
“Not Ready To Arm – System Trouble” is displayed in a yellow status bar along
the top of the screen. A low battery icon along with “Low Battery” is displayed
when the system’s backup battery power is low.
Appears when the system has detected an RF jamming condition or excessive
interference.
AC Loss
Displayed when the system has lost AC power. “Ready To Arm – System
Trouble” is displayed in a yellow status bar along the top of the screen.
Automation
Displayed when the system has detected a Z-Wave Device Failure
Displayed when the Garage Door has been opened. Ready To Arm – Fault” is
Fault *
displayed in a yellow status bar along the top of the screen. (* Applicable Zone
Main
Garage Door Number)
Displayed in the upper left corner of the status bar. Indicates that the system is
(Not
connected to a WiFi source and the signal strength.
applicable)
Not
applicable)
Displayed in the upper left corner of the status bar. Indicates that the system is
NOT connected to a WiFi source.
– 12 –
SYSTEM OVERVIEW
Navigating Menus
LCD Display
LYNX Touch’s Liquid Crystal Display (LCD) touch screen displays variable icons and text on “screens”. The
screen displays status icons and associated text, the current time, system status information and menu choices.
The system status is displayed in a colored status bar along the top of the screen. The status bar color is
variable and will change between Red, Yellow and Green as the system status changes.
The Menu area includes a list of commands, or choices that apply to the current selection. The status area
provides information about various system events. A Home Screen is displayed whenever power is applied to
the system. In addition, the Green (Home) and the Red (Panic) key
s will be lit.
Note: The displayed screens may vary slightly depending upon the devices and services that are installed in or connected to your
system.
Navigation Keys
Navigating through the screens is accomplished by lightly touching the menu item on the touch screen. Once
activated, the control will take you to the next screen. Selecting the “Home” (cancel) key will return you to the
Home Screen at any time unless System Programming mode is active. Pressing the “” Key or “Back” tab will
return you to the previous screen.
Note: You may find it convenient to adjust the volume setting before entering the Program (Tools) Mode. This will allow you to
clearly hear the feedback announcements or system beeps in the Programming Mode, of the system’s built-in speaker. To
adjust the volume, select “More” on the “home Screen” and then select “Settings”. Adjust the volume using the slide shown
on the Settings screen and then select “Save” to accept.
Home Screen
System Status is displayed at the top of the Home Screen. The time and date is displayed on the left third of the
screen and the Security, Automation, Video and Notices icons or “buttons” are displayed on the right side of the
screen. If your system is connected to Total Connect Services the Home Screen will display the time, date and
weather (as applicable) on the left third of the screen. Additionally News and Traffic selection icons or “buttons”
are displayed. Additionally News, Traffic and Notices selection icons or “buttons” are displayed.
Note: Access to Text Messages, Weather, News and Traffic and other web content requires Total Connect Services. Ask your
Installer, which of these features have been programmed in your system.
•
•
•
•
•
•
•
•
•
Security – Provides access to Security Screen.
Automation – Provides access to the Device and Z-Wave Home Automation Management screen.
Video – Provides Access to the Video Control Screen
Notices – Provides access to the Dealer Notification Message Center (TotalConnect Services required)
News – Provides access to News Updates (TotalConnect Services required)
Traffic – Provides access to Traffic Updates (TotalConnect Services required)
5-Day Forecast – Provides access to Local 5-Day Weather forecast (TotalConnect Services required)
Weather – Provides local forecast and severe weather alerts (TotalConnect Services required)
Location – Provides access to program location information (City, State, Country, Zip Code) and enable
single day weather display and Sunrise/Sunset scheduling. (Requires GSM/Cellular or WiFi communication
module). Check with your installer to see if your system is equipped with a Communications Module.
Ready To Arm
12:35
PM
January 12, 2010
Mostly Sunny
Security
Automation
Video
News
Traffic
Notices
68 F
Feels like 71 F
5-Day Forecast
7000-100-005-V0
LYNX Touch Dashboard Screen (Typical)
– 13 –
SYSTEM OVERVIEW
Navigating Menus
Function Keys
Two Function Keys allow you to quickly access Panic functions and return to the Home Screen.
WiFi
STATUS
SYSTEM
STATUS
Ready To Arm
System
Zones
Arm Away
Arm Stay
Delay
Message
More
10:18 AM June 8, 2014
HOME
FUNCTION
KEY
PANIC
FUNCTION
KEY
7000-100-012-V1
LYNX Touch Security Screen (Page 1)
Menu Screens
System Status is displayed at the top of each screen. The time and date are displayed at the bottom of the
Security Screen.
Menus
Security Screen Menu
The two-page Security Screen provides access to an Unrestricted Menu that displays the system status and
selection icons or “buttons”. The appearance of the display and the location of the icons varies dependent upon
the options that have been programmed. Check with your Installer. The “More/Back” button is used to toggle
between the Security Screen pages.
Icon or Button
Arm Away
Arm Stay
Function
Icon or Button
Used to Arm the system in Away mode.
(Displayed on both pages of the
Security screen)
Tools
Used to Arm the system in Stay mode.
(Displayed on both pages of the
Security screen)
Zones
Provides access to Zone information
and options.
System
Provides information about system
status.
Settings
Delay/Instant
More/Back
Provides access to Message Center.
Message
– 14 –
Function
Provides access to Master User
Programming Menus (Master User
Code required for access).
Provides access to Touch Screen
functions including Brightness, Contrast,
Volume, Voice, Chime and Ringer.
Toggles between Delay and Instant to
enable the exit delay or instant arming
options.
Advances system to second page of the
Security Screen/Returns system to first
page of the Security Screen.
SYSTEM OVERVIEW
Navigating Menus
Master Menu
The User Menu provides access to User configurable features. The appearance of the icons varies dependent
upon the options that have been programmed. Entering the Master User Code is required to access the Master
menu.
Ready To Arm
Users
Events
Test
Keypad
Date Time
Reminders
Slide Show
WiFi Config
Back
5200-100-036-V0
Icon or Button
Function
Allows Master User to add or remove User Codes
Users
Allows Master User to view system events.
Events
Allows Master User to Test the system.
Test
Keypad
Allows Master user to enroll and view information associated with Mobile
Device(s).
Used to program Date and Time.
Date Time
Allows Master User to add or remove local and “Follow Me” reminders.
Reminders
Allows Master User to program screensaver options.
Slide Show
WiFi Config
Back
Provides access to WiFi configuration screen (Requires the installation of WiFi
Communications Module).
Returns system to the First Page of the Security Screen.
– 15 –
SECURING THE PREMISES
System Status
General Information
Before arming your system, all protected doors, windows, and other protection zones must be closed or bypassed
(refer to the Bypassing Zones section).
Home Key:
The Home Key (Ready indicator) on the control will be lit Green when the system is ready to be
armed. If the Button is blinking Green, the system is not ready to arm.
VOLUME LEVEL: The volume level of system announcements can be increased or decreased. Refer to the System
Adjustment section for the procedure.
System Can Be Armed
The Home Key (Ready indicator) will be lit Green once all protection zones have been closed or bypassed.
Additionally, “Ready to Arm” is displayed in a green band at the top of the touch screen. You may now arm the
system.
– 16 –
SECURING THE PREMISES
Arming the System
Arming in Stay Mode
Use this mode when you are staying home, but expect someone to use the entrance door later. Close all
protected perimeter windows and doors before arming. The green Ready indicator on the control should be lit if
the system is ready to be armed. When armed in STAY mode, the system will sound an alarm if a protected
door or window is opened, but you may otherwise move freely throughout the premises. Late arrivals can enter
through the designated entrance door without causing an alarm, but they must disarm the system within the
entry delay period or an alarm will occur. If Quick Arm was programmed by the installer, you do not need to
enter the security code to arm the system. The security code must always be used to disarm the system,
however.
If your system’s Garage Door Zone has been programmed for burglary protection, the system can be armed
while the Garage Door is opened. A “Fault” will be displayed by the control but will clear once the door has been
closed. The Garage Door zone will be subsequently be monitored by the system.
The Guest Code and Installer Code cannot disarm the system unless it was used to arm the
system. In addition, if the system is armed by pressing via Quick-Arming, neither the Guest Code
nor Installer Code can disarm the system.
Ready To Arm
Arm Stay
Delay
Select the Arm Stay icon, the system beeps once and
displays a keypad.
2.
Enter a valid User Code.
OR
If Quick Arm has been enabled, select the “Quick Arm” icon.
System
Zones
Arm Away
1.
Message
More
10:18 AM June 8, 2010
7000-100-020-V0
Ready To Arm
Arm the system in Stay mode
1
2
3
4
5
6
7
8
9
Clear
0
Enter Code:
Cancel
Quick Arm
Note: If a valid user code is not entered or the Confirm icon has
not been selected within 10 seconds, the system returns to
the “home” screen and it will not be armed.
5200-100-015-V0
Armed Stay - Exit Now
3.
Exit now
28 seconds
Zones
Disarm
Restart
The system beeps three times and announces “Armed Stay
Exit Now”. The exit delay screen is displayed. If programmed
the display counts down the time remaining in the exit delay.
System
Message
10:18 AM June 8, 2010
More
7000-100-021-V0
– 17 –
SECURING THE PREMISES
Arming the System
Armed Stay
Zones
Disarm
4.
At the end of the exit delay the system announces
“Armed Stay” and displays the “Armed Stay” screen.
System
Message
10:18 AM June 8, 2010
More
7000-100-022-V0
If an invalid User Code is entered or if a valid user code has not been entered within 10 seconds, the system
will return to the “home” screen and it will not be armed.
Auto Stay Arming Feature
If this feature is enabled by installer, the LYNX Touch, when armed AWAY from the control’s keypad or a Wireless Keypad,
automatically switches to the STAY mode if the Exit Time expires and no exit has been made. Exit must be made through
an Entry/Exit Zone (door). If exit is made through a Garage Door, the system will automatically switch to the STAY mode
when the Exit Time expires.
NOTE:
If the exit route entry/exit sensor is in a check condition or has been bypassed it will result in a loss of interior protection because the
alarm system will arm STAY in this case. Consult with your installer for servicing of the entry exit zones or to turn off this feature if a
check condition on entry exit zones occurs.
Arming in Night Stay Mode
Use this mode when you are staying home, but require increased security. The mode Arms same as STAY mode,
but also arms preselected interior sensors (programmed by your installer), while other interior sensors are left
disarmed. This mode can be armed when you are staying home but expect someone to use the entrance door
later. However, persons entering later can enter through an entry/exit door but they must disarm the system
and must not violate any of the programmed interior zones to avoid sounding an alarm. Close all protected
perimeter windows and doors before arming. The green Ready indicator on the control should be lit if the
system is ready to be armed. When armed in Night STAY mode, the system will sound an alarm if a protected
zone is faulted, but you may otherwise move freely throughout the premises. Late arrivals can enter through
the designated entrance door without causing an alarm, but they must disarm the system within the entry
delay period or an alarm will occur. If Quick Arm was programmed by the installer, you do not need to enter the
security code to arm the system. The security code must always be used to disarm the system, however.
When NIGHT-STAY mode is on, the selected interior zones are armed and cause an alarm if anyone
enters those areas (e.g., waking in the middle of the night). To avoid sounding an alarm, you must
disarm the system before any activity takes place in those interior zones.
The Guest Code and Installer Code cannot disarm the system unless it was used to arm the
system. In addition, if the system is armed by pressing via Quick-Arming, neither the Guest Code
nor Installer Code can disarm the system.
Ready To Arm
Zones
Arm Away
Delay
Arm Stay
1.
Select the Arm Stay icon, the system beeps once and
displays a keypad.
System
Message
10:18 AM June 8, 2010
More
7000-100-020-V0
– 18 –
SECURING THE PREMISES
Arming the System
Ready To Arm
Arm the system in Stay mode
1
2
3
4
5
6
7
8
9
Clear
0
Enter Code:
Arm Night
Cancel
Quick Arm
2. Select the ”Arm Night”, then enter a valid User Code.
OR
If Quick Arm has been enabled, select the “Quick Arm” icon.
Note: If a valid user code is not entered or the Confirm icon has
not been selected within 10 seconds, the system returns to
the “home” screen and it will not be armed.
5200-100-082-V0
Armed Stay - Exit Now
3.
The system beeps three times and announces “Armed Stay
Exit Now”. The exit delay screen is displayed. If programmed
the display counts down the time remaining in the exit delay.
4.
At the end of the exit delay the system announces “Armed
Stay” and displays the “Armed Stay” screen.
Exit now
28 seconds
Zones
Disarm
Restart
System
Message
10:18 AM June 8, 2010
More
7000-100-021-V0
Armed Stay
Zones
Disarm
System
Message
10:18 AM June 8, 2010
More
7000-100-022-V0
If an invalid User Code is entered or if a valid user code has not been entered within 10 seconds, the system
will return to the “home” screen and it will not be armed.
– 19 –
SECURING THE PREMISES
Arming the System
Arming In Away Mode
Use this mode when no one will be staying on the premises. Close all protected perimeter windows and doors
before arming. The green Ready indicator on the control should be lit if the system is ready to be armed. When
armed in AWAY mode, the system will sound an alarm if a protected door or window is opened, or if any
movement is detected inside the premises, when infrared detection devices are used. You may leave through a
designated entrance door during the exit delay period without causing an alarm. You may also re-enter through
the entrance door, but you must disarm the system within the entry delay period or an alarm will occur. If
Quick Arm was programmed by the installer, you do not need to enter the security code to arm the system. The
security code must always be used to disarm the system, however. If your system’s Garage Door Zone has been
programmed for burglary protection, the system can be armed while the Garage Door is opened. A “Fault” will
be displayed by the control but will clear once the door has been closed. The Garage Door zone will subsequently
be monitored by the system. If Auto Stay Arming is enabled, the system will Arm in STAY mode if the Exit
Time expires and no exit has been made. Refer to Auto Stay Arming Feature for additional information.
The Guest Code and Installer Code cannot disarm the system unless it was used to arm the system. In addition,
if the system is armed by pressing via Quick-Arming, neither the Guest Code nor Installer Code can disarm the
system.
Ready To Arm
Arm Stay
Delay
Select the Arm Away icon, the system beeps once and
displays a keypad.
2.
Enter a valid User Code.
OR
If Quick Arm has been enabled, select the “Quick Arm”
icon.
The system beeps two times and announces “Armed Away
Exit Now. The exit delay screen is displayed. If
programmed the display counts down the time remaining in
the exit delay in seconds.
System
Zones
Arm Away
1.
Message
More
10:18 AM June 8, 2010
7000-100-020-V0
Ready To Arm
Arm the system in Away
mode
1
2
3
4
5
6
7
8
9
Clear
0
Enter Code:
Cancel
Quick Arm
Note:
5200-100-120-V0
Armed Away - Exit Now
3.
Exit now
28 seconds
Zones
Disarm
Restart
If a valid user code is not entered or the Confirm icon has not
been selected within 10 seconds, the system will return to the
“home” screen and it will not be armed.
If “Exit Warning” has been enabled, the system will
continue to beep throughout the exit delay. Rapid beeps
will sound for the final 10 seconds of the delay period.
System
Message
10:18 AM June 8, 2010
More
7000-100-023-V0
– 20 –
SECURING THE PREMISES
Arming the System
4.
Armed Away
Zones
Disarm
At the end of the exit delay the system will announce “Armed
Away” and displays the “Armed Away” screen.
System
Message
More
10:18 AM June 8, 2010
7000-100-024-V0
If an invalid User Code is entered or if a valid user code has not been entered within 10 seconds, the system will
return to the “home” screen and it will not be armed.
Silent Exit Feature
If Silent Exit feature is enabled, when the LYNX Touch is armed AWAY, the Exit beeps will be silenced. In
addition, the panel will double the exit delay time before arming AWAY.
Ready To Arm
Zones
Arm Away
Arm Stay
Delay
1.
Select the Arm Away icon, the system displays a keypad.
2.
Select the Silent Exit button. If enabled, the Silent Exit button
turns green. Enter a valid User Code.
OR
If Quick Arm has been enabled, select the “Quick Arm” icon.
3.
The system beeps two times and announces “Armed Away
Exit Now. The exit delay screen is displayed. If programmed
the display counts down the time remaining in the exit delay
in seconds.
System
Message
More
10:18 AM June 8, 2010
7000-100-020-V0
Ready To Arm
Arm the system in Away
mode
1
2
3
4
5
6
7
8
9
Clear
0
Enter Code:
Silent Exit
Cancel
Quick Arm
5200-100-018-V0
Armed Away - Exit Now
Exit now
28 seconds
Zones
Disarm
Restart
System
Message
10:18 AM June 8, 2010
More
7000-100-023-V0
– 21 –
SECURING THE PREMISES
Arming the System
Armed Away
Zones
Disarm
4.
At the end of the exit delay the system will announce
“Armed Away” and displays the “Armed Away” screen.
System
Message
10:18 AM June 8, 2010
More
7000-100-024-V0
If an invalid User Code is entered or if a valid user code has not been entered within 10 seconds, the system
will return to the “home” screen and it will not be armed.
– 22 –
SECURING THE PREMISES
Arming the System
Arming the System with no delay (Instant)
Use “Instant” with Stay mode when you are staying home and do not expect anyone to use the entrance door.
Use “Instant” with Away mode when the premises will be vacant for extended periods of time such as vacations,
etc. When armed with “Instant”, the system will sound an alarm if a protected door or window is opened,
including the entrance door. You may leave through the entrance door during the exit delay period without
causing an alarm, but an alarm will sound as soon as someone reenters.
When armed “Instant” with Stay mode, the control beeps three times and displays the “Armed Stay Instant”
message. In addition, the red Armed indicator lights and the system announces “Armed Stay Instant –exit now”.
When armed “Instant” with Away mode, the control beeps two times and displays the “Armed Away Instant”
message. If Exit Warning is enabled the system beeps continuously for the duration of the exit delay. In
addition, the red Armed indicator lights and the system announces “Armed Away Instant –exit now”.
To Arm the System with No Delay (Instant)
Ready To Arm
1.
2.
Zones
Arm Away
Delay
Arm Stay
System
Select the “Delay” tab on the Security Screen. The icon
“toggles” and “Instant” is displayed.
Arm the system in the “Stay” or Away” mode normally.
Note: The entry delay time is eliminated when “Instant” is selected.
Message
10:18 AM June 8, 2010
More
7000-100-020-V0
Quick Exit
If active, you can restart the exit delay at any time after the system has been armed in Stay or Away mode by
selecting the “Quick Exit” icon. This avoids having the user disarm then re-arm the system after allowing
someone to enter or exit. The system will re-arm once the exit delay expires.
Ready To Arm
1.
Select the “Quick Exit” icon to restart the exit delay.
Note: Quick Exit is active in Away mode when: Auto Stay mode is
enabled and no entry/exit zone has been faulted during the exit
delay period.
Zones
Arm Away
Delay
Arm Stay
System
Message
10:18 AM June 8, 2010
More
7000-100-020-V0
– 23 –
SECURING THE PREMISES
Entry/Exit Delays
Exit Delay
Exit delay begins immediately after arming the system, and gives you time to leave through the designated exit
door without setting off an alarm. The system display will count down the time remaining in the exit delay, if
programmed by your installer. If the system has been Armed Away, a slow beeping will sound throughout the
exit delay period, if programmed by your installer. The exit door must be closed before the end of the exit delay.
During the last 10 seconds of the exit delay fast beeps will sound as a warning that the delay time is nearing its
end. The exit beeps cannot be silenced.
Restarting Exit Delay While System Armed
Ask your installer if this feature is active for your system. If active, you can restart the exit delay one time after
arming in Stay or Away mode during the exit delay by selecting the “Restart” key. This will allowing extra time
for someone to enter or exit or re-enter the property before the system is armed.
Armed Stay - Exit Now
Exit now
28 seconds
Zones
Disarm
Restart
System
Message
10:18 AM June 8, 2010
More
7000-100-021-V0
Exit Alarms
To minimize false alarms sent to the alarm monitoring company, your system may have been programmed for
this feature. Ask your installer if Exit Alarm is active for your system.
Whenever you arm the system, the exit delay begins. If an entry/exit door or interior zone is faulted when the
exit delay ends (e.g., exit door left open), the system sounds an alarm and starts the entry delay timer. If you
disarm the system before the entry delay ends, the alarm sound stops and the message “Alarm Cancelled is
displayed, in the system bar. Additionally, Alarm and the faulted zone are displayed with their associated icons
in the system/zone status area. No message is sent to the alarm monitoring company. To clear the exit alarm
condition, the open zone must be secured. To clear the display, select the “Disarm” icon OR depress the “Off”
key and then enter your security code.
If you do not disarm the system before the entry delay ends, and an entry/exit door or interior zone is still open,
the alarm sound continues and an "exit alarm" message is sent to the alarm monitoring company. The message
“Alarm Exit Error" is displayed, in the system bar. Additionally, Alarm and the faulted zone are displayed with
their associated icons in the system/zone status area. The alarm will continue to sound until the system is
disarmed or timeout ocurs. To stop the alarm, the system must be disarmed by selecting the “Disarm”
icon OR depressing the “Off” key and then entering your security code. The message “Alarm Cancelled" is
displayed, in the system bar, indicating that the alarm has been cancelled (if this feature is enabled by the
installer). “Alarm” and the faulted zone continue to be displayed with their associated icons in the system/zone
status area. To clear the display, select the “Disarm” icon OR depress the “Off” key and then enter your security
code a second time. An exit alarm also results if an entry/exit door or interior zone is faulted within two
minutes after the end of the exit delay.
– 24 –
SECURING THE PREMISES
Entry/Exit Delays
Entry Delay
Entry Delays give you time to disarm the system when you re-enter through the designated entrance door. You
must disarm the system before the entry delay period ends, or an alarm will occur. The control beeps during the
entry delay period, reminding you to disarm the system. There are two entry delays (if programmed). The first
is for your primary entrance and the second can be used for a secondary entrance, where a longer delay is
required to walk to the control to disarm the system. You can also arm the system with no entry delay at all by
selecting the “Delay” icon prior to arming the system. This will toggle the system to “Instant”, which can
provide greater security while on the premises or while away for extended periods of time. See Arming the
System section for procedure. See your installer for delay times programmed for your system.
Exit Delay:
45, 60, 90 seconds, 2 minutes
Entry Delay 1:
None, 15, 30, 45, 60, 90 seconds, 2, 3, 4 minutes
Entry Delay 2:
None, 15, 30, 45, 60, 90 seconds, 2, 3, 4 minutes
LYNX Touch (L7000CN) Canada Exit/Entry Delay Times
Exit Delay:
None, 15, 30, 45, 60, 90 seconds, 2 minutes
Entry Delay 1:
None, 15, 30, 45, 60, 90 seconds, 2 minutes
Entry Delay 2:
None, 15, 30, 45, 60, 90 seconds, 2 minutes
– 25 –
SECURING THE
THE PREMISES
Disarming the System
Select the “Disarm” icon or the “Off” key to disarm the system and to silence alarm and trouble sounds. See the
Summary of Audible & Visual Notifications section for information, which will help you to distinguish between
fire and burglary alarm sounds. During Entry Delay or when an Alarm Condition exists, the system will be
disarmed as soon as the correct user code is entered on the touch screen. Selecting the Off key is not required.
The entry beeps or alarm sound can be silenced by pressing any key however, it will restart in 10 seconds if the
correct User Code is not entered. The Ready indicator will light (if no alarms have occurred while armed) and
the control will beep once to confirm that the system is disarmed.
**IMPORTANT**
If the LYNX Touch is beeping rapidly upon entering the premises, an alarm has occurred during your absence
and an intruder may still be on the premises. LEAVE IMMEDIATELY and CONTACT THE POLICE from a
nearby safe location.
Disarming the System
Armed Stay
1.
System
Zones
Disarm
Select the “Disarm” icon. The system beeps once and
displays a keypad.
Message
More
10:18 AM June 8, 2010
7000-100-022-V0
Armed Stay
2.
1
2
3
4
5
6
7
8
9
Clear
0
Enter a valid Code. The system beeps once and announces
“Disarmed Ready to Arm”.
Note: If a valid user code is not entered or the Confirm icon has
not been selected within 30 seconds, the system returns
to the “home” screen and it will not be disarmed.
Enter Code:
Cancel
5200-100-022-V0
If an invalid User Code is entered, system will return to the Security Screen.
Disarming the System During Entry Delay
Armed Stay - Disarm Now
Disarm Now
ARMED
1
2
3
4
5
6
7
8
9
Clear
0
READY
Enter Code:
Cancel
Upon entering the premise when the system is armed, the control
announces “disarm system now”.
1.
Enter a valid Code. The system beeps once and announces
“Disarmed Ready to Arm”.
Note: If a valid user code is not entered before the programmed
entry delay occurs, the system enters alarm mode.
5200-100-023-V0
– 26 –
SECURING THE PREMISES
Disarming the System
When an Alarm Occurs
When an alarm has occurred, the touch screen displays the zone number(s) that caused the alarm and the type
of alarm (e.g., “Fire Alarm”). These messages remain displayed until cleared by a user. To clear the display,
note the zone number that is displayed and enter an Off sequence. If the fault cannot be corrected, notify your
alarm company.
Disarming the System and Silencing Alarms
Alarm
Alarm 2 Front
Door
1
2
3
4
5
6
7
8
9
Clear
0
1. Enter a valid Code. The system beeps once and announces
“Disarmed Ready to Arm”.
Note: If a valid user code is not entered before the programmed
entry delay occurs, the system remains in alarm mode.
Enter Code:
Cancel
5200-100-088-V0
Alarm Cancel
Alarm 2 Front
Door
Zones
Disarm
System
2. “Alarm Cancel” is displayed in a red band along with the zone
that caused the alarm. Select the “Disarm” icon and enter an
second Off sequence to clear the alarm. The system beeps
once, returns to the Security Screen and announces
“Disarmed Ready to Arm”.
Message
4:43 PM August 11, 2011
More
7000-100-026-V0
– 27 –
SECURING THE PREMISES
Bypassing Protection Zones
Bypassing Individual Zones
The Bypass feature can be used when you want to intentionally arm your system with one or more zones
unprotected. Bypassed zones are unprotected and will not cause an alarm when violated while your system is
armed. All bypasses are removed when an Off sequence is performed. The system will not allow
Panic, Fire or CO zones to be bypassed.
Bypassing Zones
Not Ready To Arm - Fault
1. With the system in the disarmed state, select the “Zones”
icon. The system displays the Zones/Bypass screen.
Fault 2
Front Door
Zones
System
Message
Delay
More
10:18 AM June 8, 2010
7000-100-027-V0
Not Ready To Arm - Fault
2. Front
Door
2. Select the zone(s) that you wish to bypass and then select
“Bypass” OR if programmed, the “Bypass All Faulted” button
allows you to bypass all faulted zones (excluding Panic, Fire
or CO zones). The system displays a keypad.
FAULT
Bypass All
Faulted
Clear
Bypasses
Bypass
Select
Fault
5200-027-027-V0
Not Ready to Arm - Fault
Bypass Selected Zones
Enter Code:
Cancel
1
2
3
4
5
6
7
8
9
Clear
0
3. Enter a valid Code. The system returns to the Bypass screen
and the zone(s) that are bypassed will be displayed.
4. Select the icon to return to the Security Screen.
5. Arm the system normally. See Arming the System section for
the procedure.
5200-100-083-V0
– 28 –
SECURING THE PREMISES
Bypassing Protection Zones
Displaying/Clearing Bypassed Zones
Ready To Arm - Bypass
Arm Away
Delay
Arm Stay
Zones
System
Message
Phone
More
10:18 AM June 8, 2010
5200-100-014-V0
Ready To Arm - Bypass
2. Front
Door
BYPASSED
3. Garage
Door
1. With the system in the disarmed state, select the “Zones”
icon. The system displays the Zone screen and the status for
each zone will be indicated.
2. Use the “” “” buttons to scroll to additional pages and view
the zone status.
3. If you select the “Select All” button it scrolls through the
following: “Select All”, “Select Alarm”, “Select Trouble”, “Select
Fault” and Select Bypassed”. The system displays the
associated zones.
Note: If one or more zones has been bypassed the “Clear
Bypasses” button will be highlighted.
READY
96. Medical
95. Fire
READY
READY
99. Police
READY
Bypass All
Faulted
Clear
Bypasses
Bypass
Select
All
5200-100-029-V0
Ready To Arm - Bypass
2. Front
Door
BYPASSED
3. Garage
Door
4. To clear the bypass, select the bypassed zone(s), then select
the “Clear Bypasses” button.
5. Enter a valid code on the displayed keypad. The system
returns to the Zones screen.
6. Select the icon to return to the Security Screen.
READY
96. Medical
95. Fire
READY
READY
99. Police
READY
Bypass All
Faulted
Clear
Bypasses
Bypass
Select
All
5200-100-030-V0
– 29 –
SECURING THE PREMISES
Panic Keys
Panic Keys
Your system may have been programmed to use special icons to manually activate panic functions. The
functions that might be programmed are listed below. See your installer for the function(s) that may have been
programmed for your system.
Note: Your installer should advise which functions are active in your system.
Panic Icons
Icon
Function
When activated, alerts the alarm monitoring company that a fire condition exists.
Fire
When activated, alerts the alarm monitoring company that a police emergency exists.
Police
When activated, alerts the alarm monitoring company that a health emergency exists.
Medical
Types of Panic Alarms
• A silent emergency/silent alarm sends an alarm signal to the alarm monitoring company, if your system
is connected to an alarm monitoring company, but there will be no audible alarms or visual displays.
• An audible emergency/audible alarm sends an emergency message to the alarm monitoring company, if
your system is connected to an alarm monitoring company, and sounds a loud, steady alarm at your control.
(“ALARM” will be announced and the Alarm icon is displayed along with “Alarm” and “Alarm 99 Police”
alternately.
• A personal emergency/aux alarm sends an emergency message to the alarm monitoring company, if
your system is connected to an alarm monitoring company, and sounds at controls, but not at external
sounders. . (“ALARM” will be announced and the Alarm icon is displayed along with “Alarm” and with
“Alarm 96 Medical”.
• A fire alarm sends a fire alarm message to the alarm monitoring company, if your system is connected to
an alarm monitoring company, and uniquely activates the sounder. The Fire Alarm icon is displayed along
with “Fire Alarm 95 Fire”.
Activating a Panic Alarm
Ready To Arm
Police
Fire
1. With the system in the disarmed or armed state, depress and
hold the “Panic” key until the system displays the Panic
screen (approximately 3-4 seconds).
2. Touch the desired panic icon on the screen.
3. If applicable, the alarm sounds and the associated icon is
displayed.
Medical
5200-100-031-V0
Fire Alarm
Fire Alarm
95 Fire
Enter Code:
Cancel
1
2
3
4
5
6
7
8
9
Clear
0
Note: Dependent upon how your system has been programmed
a keypad may be displayed. This will allow you to cancel
the alarm by entering valid User Code on the keypad.
5200-100-032-V0
– 30 –
SECURING THE PREMISES
Chime Mode
Chime Mode
Your system can be set to provide you with an audible alert of the opening of a door, while it is disarmed, by
using Chime mode. When activated, three beeps or a programmed chime will sound at the control whenever a
protected perimeter door is opened and the zone voice descriptor will be announced, if programmed. The Chime
mode can be changed only when the system is disarmed. Additionally, the faulted zone information will be
displayed on the Security Screen. Selecting the “Zones” icon displays the open protection points.
The Chime feature is intended for convenience and is not intended for life safety purposes or pool
alarm and does not meet the requirements of UL 2017.
!
Turning Chime Mode On or Off
Ready To Arm
Tools
Arm Away
Arm Stay
Settings
10:18 AM June 8, 2010
Delay
1. With the system in the disarmed state, select the “Settings”
icon from the second page of the Security Screen. The
system displays the Settings screen.
Note: The Settings Screen display is variable dependent upon
the features that have been programmed in your system.
Back
5200-100-033-V0
Ready To Arm
2. Select the “Chime” icon. The system toggles between “Off”
and “On”, and when selected the button turns green. When
“On” is selected, the Chime mode will be active.
3. Select the “Save” button to save your new settings.
4. Select the icon to return to the Security Screen.
Brightness
Volume
Clean
Voice
Chime
Save
7000-100-034-V0
Selecting Chime Sounds
Ready To Arm
1. With the system in the disarmed state, select the “Zones” icon
from Security Screen. The system displays the Zones screen.
2. Select the “Select All” button and scroll through the options
until “Select Chime” button appears.
System
Zones
Arm Away
Delay
Arm Stay
Message
More
10:18 AM June 8, 2010
7000-100-020-V0
Ready To Arm
2. Front
Door
READY
3. Garage
Door
3. Select the applicable zone from the displayed list and then
select the “Chime” button to scroll through the available
chimes. Each chime sounds when selected.
4. Select the “Save” button to save your new settings.
5. Enter the Master User code on the displayed keypad.
6. The system returns to the Security Screen.
READY
96. Medical
95. Fire
READY
READY
99. Police
READY
Chime
Standard
Save
Select
Chime
5200-100-116-V0
– 31 –
SECURING THE PREMISES
Voice Mode
Voice Mode
Your system can be set to provide you with a voice alert of system functions by activating the Voice mode. When
activated, the system will announce the system status when armed/disarmed.
Turning Voice Mode On or Off
Ready To Arm
Tools
Arm Away
Delay
Arm Stay
10:18 AM June 8, 2010
1. With the system in the disarmed or armed state, select the
“Settings” icon from the second page of the Security Screen.
The system displays the Keypad screen.
Note: The Settings Screen display is variable dependent upon
the features that have been programmed in your system.
Settings
Back
5200-100-033-V0
Ready To Arm
2. Select the “Voice” icon. The system will toggle between “Off”
and “On”, and when selected the button turns green. When
“On” is selected, the Voice mode will be active.
3. Select the “Save” button to save your new settings and return
to the Security screen.
Brightness
Volume
Clean
Voice
Chime
Save
7000-100-034-V0
– 32 –
USER FUNCTIONS
User Access
General Information
For additional security you (the Master User Code) can assign secondary user codes to individual users
enabling them to perform specific system functions. These secondary users are identified by "User Numbers"
when their codes are assigned. You can assign up to 46 user codes. Note that the Master User is the only one
who can assign codes to secondary users.
All codes can be used interchangeably when performing system functions (a system armed with one user's code
can be disarmed by another user's code), with the exception of the Guest Code described below.
• Guest Code: This code can be used to arm the system, but cannot disarm the system unless the system
was armed with this code. This code is typically assigned to someone (such as a Guest) who needs to
arm/disarm the system only at certain times.
• Duress Code: This feature is intended for use when you are forced to disarm or arm the system under
threat. When used, the system will act normally, but can silently notify the alarm monitoring company of
your situation, if that service has been provided. The Duress Code is useful only when the system is
connected to an alarm monitoring company.
IMPORTANT: Temporary users of the system (e.g., Guests, cleaning staff) should not be shown how to use any
system function they do not need to know, such as bypassing protection zones for example.
Adding a User
Ready To Arm
1. With the system in the disarmed state, select the “Tools” icon
from the second page of the Security Screen. The system
displays the Keypad screen.
Tools
Arm Away
Arm Stay
Settings
10:18 AM June 8, 2010
Delay
Back
5200-100-033-V0
Ready To Arm
Program the system
Enter Code:
Cancel
1
2
3
4
5
6
7
8
9
Clear
0
2. Enter your 4-digit Master User Code. The system displays the
Master User programming screen.
5200-100-035-V0
Ready To Arm
3. Select the “Users” icon. The system displays the Master User
screen.
Users
Events
Test
Keypad
Date Time
Reminders
Slide Show
WiFi Config
Back
5200-100-036-V0
– 33 –
USER FUNCTIONS
User Access
Ready To Arm
4. Select the “Add New” key. The system displays the User
screen.
Guest ****
Master ****
Note:
**** Following a User name indicates that a valid 4-digit User
Code has been assigned to the User.
Duress ****
Edit
Add New
Delete
5200-100-037-V0
Ready To Arm
5. Select the “Name” key, the system displays a keyboard.
03
Name
Note:
User 3
User Code
The Z-wave Lock Control option is only displayed if Z-Wave has
been enabled.
Z-wave Lock Control
No
Save
5200-100-038-V0
Ready To Arm
6. If desired you can enter a User Name. Select the “Clear” key
and then enter up to 10 characters of text.
User3
123!@#
Note:
Q
W
E
A
Clear
T
R
U
Y
I
O
S
D
F
G
H
J
K
Z
X
C
V
B
N
M
abc...
P
L
Select the “ABC…” key to switch the keyboard between
upper/lower case or the “123!@#” key to switch to numbers.
7. Once you are finished, select “Done”. The system displays
the Keypad screen.
Done
5200-100-039-V0
Ready To Arm
03
Name
Thomas
User Code
Z-wave Lock Control
****
Yes
Z-wave Unlocking Door
Disarm
Save
5200-100-040-V0
Ready To Arm
Master ****
Guest ****
Duress ****
Thomas ****
Edit
Add New
Delete
5200-100-041-V0
8. Enter the 4-digit code for the new User followed by “Done”.
The system returns to the Users Programming screen and
the new User is displayed and along with ****.
9. If a Z-Wave door lock is installed, select the “Z-wave Lock
Control” key to enable the User. The system toggles
between “No” and “Yes”. When “Yes” is selected, the User
Code will be synchronized with all enrolled Z-wave door
locks allowing the same User Code to be used at the door
locks.
Note: The number of User Codes supported by each door lock varies
between manufacturers. To ensure compatibility, set the length
of the Master User Code on the door lock to be greater than four
digits.
10. If “Yes” is selected the system displays the “Z-wave
Unlocking Door” key.
11. Select the “Z-wave Unlocking Door” key. The system toggles
between “Disabled” and “Disarm”. When “Yes” is selected,
entering a valid User Code with Z-wave Lock Control
enabled at the door lock will disarm the system.
12. Once the User programming is complete select “Save”. The
system returns to the Users screen and the new User is
shown.
Note: **** Following a User name indicates that a valid 4-digit User
Code has been assigned to the User.
– 34 –
USER FUNCTIONS
User Access
Editing/Deleting a User
Ready To Arm
1. With the system in the disarmed state, select the “Tools” icon
from the second page of the Security Screen. The system
displays the Keypad screen.
Tools
Arm Away
Arm Stay
Settings
10:18 AM June 8, 2010
Delay
Back
5200-100-033-V0
Ready To Arm
Program the system
1
2
3
4
5
6
7
8
9
Clear
0
Enter Code:
Cancel
2. Enter your 4-digit Master User Code. The system displays the
Master User programming screen.
5200-100-035-V0
Ready To Arm
3. Select the “Users” icon. The system displays the Users
screen.
Users
Events
Test
Keypad
Date Time
Reminders
Slide Show
WiFi Config
Back
5200-100-036-V0
Ready To Arm
4. Select a User Name and then select “Edit” or “Delete”. If you
are editing user information proceed to step 5. If you are
deleting a user, proceed to step 8.
Master ****
Guest ****
Duress ****
Thomas ****
Edit
Add New
Delete
5200-100-041-V0
Ready To Arm
User3
123!@#
Q
W
A
Clear
abc...
E
R
T
Y
U
I
O
S
D
F
G
H
J
K
Z
X
C
V
B
N
M
P
5. If desired you can revise a User Name. Select the “Clear” key
and then enter the desired text.
6. Once you are finished, select “Done”. The system displays the
Keypad screen. If you wish to change the assigned User
Code, proceed to Step 7 otherwise proceed to Step 9.
L
Done
5200-100-039-V0
– 35 –
USER FUNCTIONS
User Access
Ready To Arm
User Code
1
2
3
4
5
6
7
8
9
Clear
0
7. If desired, enter a new 4-digit code for the selected User
followed by “Done”. The system returns to the Users screen.
8. Select “Yes” or “No” when the confirmation screen is
displayed then proceed to step 9.
9. Select the icon to return to the Master User screen.
Done
5200-100-042-V0
– 36 –
USER FUNCTIONS
View Events
This feature allows you to view System Events such as Arming/Disarming, Zone Activity, Troubles and Alarms.
Viewing System Events
Ready To Arm
1. With the system in the disarmed state, select the “Tools” icon
from the second page of the Security Screen. The system
displays the Keypad screen.
Tools
Arm Away
Arm Stay
Settings
10:18 AM June 8, 2010
Delay
Back
5200-100-033-V0
Ready To Arm
Program the system
1
2
3
4
5
6
7
8
9
Clear
0
Enter Code:
Cancel
2. Enter your 4-digit Master User Code. The system displays the
Master User programming screen.
5200-100-035-V0
Ready To Arm
3. Select the “Events” icon. The Events screen will appear and
displays all events.
Users
Events
Test
Keypad
Date Time
Reminders
Slide Show
WiFi Config
Back
5200-100-036-V0
Ready To Arm
Sun Jun 13, 2010 15:08
Disarmed
User 2 E 441
Sat Jun 12, 2010 11:15
Armed Stay
User 1 R 441
Sat Jun 12, 2010 11:08
Burglary Bypass
Zone 3 E 570
Sat Jun 12, 2010 10:15
Disarmed
User 1 E 401
Fri Jun 11, 2010 18:08
Armed Away
User 2 R 401
Fri Jun 11, 2010 12:10
Disarmed
User 3 E 441
Fri Jun 11, 2010 11:08
Armed Stay
User 2 R 441
Fri Jun 11, 2010 10:15
Burglary Bypass
Zone 3 E 570
4. If you wish to view specific system history, select “All”. The
system displays a new menu.
All
5200-100-043-V0
Ready To Arm
All
Alarm
Trouble
Bypass
Open
or Close
NonSecurity
5. Select from the menu to display the specific event types that
you wish to view.
Note: The Event Types that are displayed is variable dependent
upon the options that were programmed by your installer.
5200-100-044-V0
– 37 –
USER FUNCTIONS
Message Recording and Playback
The LYNX Touch Message Center allows you to record, play and delete messages. The maximum message
duration is 184 seconds.
NOTES: (1) If the system loses electrical power, all messages will be erased.
(2) Message Play/Record will not be available if a report must be sent.
Entering Message Mode
Ready To Arm
1. With the system in the disarmed state, select the “Message”
icon from the Security Screen. The system displays the
Message screen.
System
Zones
Arm Away
Arm Stay
Delay
Message
More
10:18 AM June 8, 2010
7000-100-020-V0
Recording a Message
Ready To Arm
1. Select “Add New”. The system displays the Record Message
screen.
Note: The System will display the total message recording time
available.
No items to display!
Add New
Play
Delete All
Save
5200-100-045-V0
Ready To Arm
Message 1
2. Select “Record”, the system sounds a single tone. Speak into
the microphone and record your message.
3. When you are finished recording your message, select. “Stop”
4. To listen to the message, select “Play”.
5. If you wish to delete the message, select “Delete”.
6. Record additional messages as required.
Stopped
Time Remaining : 184 Seconds
Record
Play
Delete
5200-100-046-V0
Ready To Arm
Message 1
2:48 PM
September 1, 2010
Message 2
5:09 PM
September 5, 2010
Add New
Play
6. When you have finished recording, select “”. The system
displays the recorded messages.
7. To record additional messages (if recording time is available)
repeat steps 1 through 3.
Delete All
5200-100-047-V0
NOTE: If you are trying to record a new message and the message center is already full, “Add New” will not be displayed. If the
message center is full all old messages must be deleted before new messages can be recorded. See the Deleting
Messages section.
– 38 –
USER FUNCTIONS
Message Recording and Playback
Playing Message(s)
Ready To Arm
Message 1
2:48 PM
September 1, 2010
Message 2
5:09 PM
September 5, 2010
1.
2.
3.
4.
Add New
Play
At the Message screen, select the message you wish to
play.
Select “Play”, the system plays your message.
When you are finished listening to the message, you may
select. “Stop”. If “Stop” is not selected the system continues
to play the remaining messages.
When you have finished listening to the messages, select
“”. The system returns to the Security Screen.
Delete All
5200-100-047-V0
Deleting Messages
Ready To Arm
Message 1
2:48 PM
September 1, 2010
Message 2
5:09 PM
September 5, 2010
Add New
Play
1.
2.
At the Message screen, select “Delete All”. The system
deletes all messages.
When you have finished deleting the messages, select “”.
The system returns to the Security Screen.
Delete All
5200-100-047-V0
– 39 –
USER FUNCTIONS
System Settings
The volume level of message playback, system announcements, and status beeps can be changed if desired.
Additionally, you can adjust the display’s brightness and turn on or off the Chime.
Change System Settings
Ready To Arm
Tools
Arm Away
Delay
Arm Stay
10:18 AM June 8, 2010
1. With the system in the disarmed or armed state, select the
“Settings” icon from the second page of the Security Screen.
The system displays the Settings screen.
Note: The Settings Screen display is variable dependent upon
the features that have been programmed in your system.
Settings
Back
5200-100-033-V0
Ready To Arm
Brightness
Volume
Clean
Voice
Chime
2. Increase or decrease the Display Brightness or the System
Volume by using the sliding adjustment from left (decrease) to
right (increase).
3. Turn the Voice or Chime On or Off by selecting the
appropriate icon. The system toggles between “On” and “Off”,
and when selected the button turns green.
4. Select “Save” when you are finished. The system returns to
the second page of the Security Screen.
Save
7000-100-034-V0
– 40 –
USER FUNCTIONS
Clock/Calendar
Note: If your system is equipped with a 4GLT/4GLTC or ILP5 Communication Module, the time and date will be programmed and
updated automatically via Central Station. You may still program the correct Time Zone as shown below. Check with your
installer to see if your system is equipped with a Communications Module.
Setting the Date and Time
Note: The system must be disarmed in order to set the date and
time.
Ready To Arm
Tools
Arm Away
Arm Stay
Settings
10:18 AM June 8, 2010
Delay
1. With the system in the disarmed state, select the “Tools” icon
from the second page of the Security Screen. The system
displays the Keypad screen.
Back
5200-100-033-V0
Ready To Arm
Program the system
1
2
3
4
5
6
7
8
9
Clear
0
Enter Code:
Cancel
2. Enter your 4-digit Master User Code. The system displays the
Master User programming screen.
5200-100-035-V0
Ready To Arm
3. Select the “Date Time” icon. The Calendar screen will appear.
Users
Events
Test
Keypad
Date Time
Reminders
Slide Show
WiFi Config
Back
5200-100-036-V0
Ready To Arm
June
SUN
MON
4.
5.
6.
7.
2010
TUE
WED
THU
FRI
SAT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Select the correct month by using the “⊳” and “”.
Select the correct year by using the “⊳” and “”.
Select the correct day on the calendar.
When you have finished select the “” icon. The system
advances to the time screen.
Save
5200-100-048-V0
– 41 –
USER FUNCTIONS
Clock/Calendar
Ready to Arm ...
Enter Time
10:21
AM
AM / PM
1
2
3
4
5
6
7
8
9
Clear
0
8. If the displayed time is not correct, select “Clear” then enter
the correct time (4 digits) on the keypad and select AM or PM.
9. When you have finished select the “” icon. The system
advances to the next screen OR proceed to step 17.
Save
5200-100-049-V0
Ready To Arm
10. Select “Time Zone”. The system scrolls between through the
following options:
Time Zone
Eastern (EST)
Day Light Savings Time
Yes
Start Month
Start Week
March
Second
End Month
End Week
November
First
Save
5200-100-050-V0
Eastern (EST)
Central (CST)
Mountain (MST)
Pacific (PST)
Hawaii (HAST)
Alaska (AKST)
Brasilia (BRT)
Mid-Atlantic (MAT)
Atlantic (AST)
Newfoundland (NT)
Select the correct time zone.
11. Select “Day Light Savings Time”. The system toggles between
“Yes” and “No”.
Note: The start month/week and end month week are default
programmed
to
“March/Second”
and
“November/First”
respectively. Steps 13 to 16 should only be performed if you wish
to change those entries. If you are not changing the defaults,
advance to step 17.
Ready To Arm
January
February
March
April
May
June
July
August
5200-100-051-V0
12. Select “Start Month”. The system displays a calendar. Select
the correct month.
13. Select “Start Week”. The system will toggle between:
Second
Third
Fourth
Last
Next to Last
3rd from Last
First
14. Select “End Month”. The system displays a calendar. Select
the correct month.
15. Select “End Week”. The system will toggle between:
First
Second
Third
Fourth
Last
Next to Last
3rd from Last
16. When you are finished select the “Save” key. The system
returns to the Master User program screen.
– 42 –
USER FUNCTIONS
Clock/Calendar
If your system is equipped with a GSMVLP5-4G/GSMVLP5CN4G, 4GL/4GLC or ILP5 Communication Module,
but is not subscribed to TotalConnect Services it can be programmed to receive single day weather information.
Check with your installer to see if this option is available.
Enable Single Day Weather Reporting
Ready To Arm
1. At the Home Screen, select the “Location” button. The system
advances to the Location Screen.
12:35 PM
October 1, 2013
Security
Automation
Video
Location
5200-100-121-V0
Ready To Arm
City
Country
State
Zip Code
2. Select “City”, “Country”, “State” and “Zip Code” and enter the
required information on the displayed keypad then select
“Done”. Select “Save” when all fields are complete.
Save
5200-100-123-V0
Ready To Arm
3. The Home Screen is displayed within a few minutes and local
weather will appear.
12:35 PM
October 1, 2013
Security
Mostly Sunny
68
Automation
Video
F
Feels Like 71
F
Location
5200-100-122-V0
– 43 –
USER FUNCTIONS
Automation
General Information
Automation is used to program triggers, send Follow-Me or E-mail messages of system events or program home
automation features (Z-Wave) including Rules and Scenes (if Z-Wave communications have been enabled). Up
to 40 rules can be programmed. Rules 1 through 20 are used for Triggers, Z-Wave Scenes and Follow-Me
Messages. Rules 21 through 40 are used for Z-Wave Scenes and for E-mail notification and are only accessible
through TotalConnect Service. Check with your Installer to see which options are available to you.
Note: Switches, Thermostats, Locks, Water Valves, Tools, and Scenes options will only appear when Z-wave has been enabled.
Refer to the Home Automation Guide P/N 800-16091 for information regarding these features.
Schedules
The Schedules Feature can be used to program the system to automatically perform certain functions (i.e.;
automatically arming the system in Stay mode and activating output [Z-Wave] devices) at a scheduled time,
day of the week or month, as applicable.
Programming a Scheduled Function
Ready To Arm
12:35 PM
October 1, 2013
Mostly Sunny
68
Security
Automation
Video
News
Traffic
Notices
1. With the system in the disarmed state, select the
“Automation” icon from the Home Screen. The system
displays the first page of the Automation screen. Select the
“” icon to advance to the second page of the Automation
screen.
F
Feels Like 71
F
5-Day Forecast
5200-100-001-V0
2. Select the “Schedules” icon. The system displays the
Scheduling screen.
Ready To Arm
Scenes
Tools
Schedules
Garage door setup
Note: Rules 21-40 are only accessible through TotalConnect Service.
Rules
5200-100-053-V0
Ready To Arm
3. Select “Add New”. The system displays the scheduling
options screen.
No items to display!
Edit
Add New
Delete
5200-100-117-V0
– 44 –
USER FUNCTIONS
Automation
4. Select “Name”. The system displays a keypad.
5. Enter a name (up to 13 digits long) for the scheduled function
on the displayed keypad then select “Done”.
6. Select “Frequency” then select one of the following displayed
options:
Ready To Arm
Name
Frequency
None
Type
None
Location
Save
5200-100-057-V0
Ready To Arm
City
Country
State
Zip Code
0
Save
5200-100-061-V0
None
Daily
Weekly
Sunrise
Once
Weekday
Monthly
Sunset
If Sunrise or Sunset is selected, select “Location” and
proceed to step 7, otherwise proceed to step 8. If Total
Connect Services are enabled proceed to step 8.
7. Select “City”, “Country”, “State” and “Zip Code” and enter the
required information on the displayed keypad then select
“Done”. Select “Save” when all fields are complete. Proceed
to step 14.
8. Program the following options based upon the Frequency
selected in step 6:
Once
Date/Start Time/End Time
Daily
Start Time/End Time
Weekday Start Time/End Time
Weekly
Start Time/End Time/Day of the Week,
Monthly
Start Time/End Time/Day of the Month
9. Select “Type” then scroll through and select one of the
following options:
None
Auto Night Stay
Auto Stay
Rules
Scene (displayed when Z-Wave has been enabled)
Ready to Arm ...
Enter Time
10:21
AM
AM / PM
1
2
3
4
5
6
7
8
9
Clear
0
Save
5200-100-049-V0
Ready To Arm
Name
Frequency
Lights
Daily
Type
Scenes
Scene
Start Time
Time Randomization
12:00 AM
No
Save
5200-100-114-V0
10. If Auto Stay is selected, select “Clear” then enter a 4-digit
time on the displayed keypad then select “Save”. If “Rules” is
selected proceed to Step 11. If “Disarm Notification” is
selected proceed to Step 12. If “Scene” is selected proceed
to Step 14.
11. Select “Rules” then select a Rule from the displayed list
(Rules 1 through Rules 20).
12. Enter a Start Time and End Time on the displayed keypad
then select “Save”.
13. Select the “” button to return to the Automation
programming screen or the Home key to return to the Home
Screen.
14. Select “Scenes”. Select the desired scene from the displayed
list.
15. Enter a Start Time and End Time on the displayed keypad
then select “Done”.
16. If “Daily”, “Weekday”, “Weekly” or “Monthly” was selected for
“Frequency”, the Randomization field is displayed. Select
“Randomization”, the system toggles between “No” and Yes”.
Note: If using the Randomization feature scheduled events should not
be programmed within one hour of each other.
17. Select “Save”. The system displays to the list of programmed
Schedules.
18. Select the “” button to return to the Automation
programming screen or the Home key to return to the Home
Screen.
– 45 –
USER FUNCTIONS
Automation
Editing a Scheduled Function
Ready To Arm
Schedule 1
Auto Stay
1. At the Schedules screen, select the Schedule you wish to
edit.
Auto Arm
Daily
Note: Rules 21-40 are only accessible through TotalConnect Service.
2. Select the “Edit” button. The Schedule programming screen
will appear. Follow the steps as noted above in the
programming a Scheduled Function section to edit and save
your changes.
Edit
Add New
Delete
5200-100-084-V0
Deleting a Scheduled Function
Ready To Arm
Schedule 1
Auto Stay
1. At the Schedules screen, select the Schedule you wish to
delete.
Auto Arm
Daily
Note: Rules 21-40 are only accessible through TotalConnect Service.
2. Select the “Delete” button. A confirmation screen will be
displayed. Select “Yes” to confirm the deletion.
3. Select the “” button. The system returns to the Automation
programming screen.
Edit
Add New
Delete
5200-100-084-V0
– 46 –
USER FUNCTIONS
Automation
Rules
Up to 40 rules can be programmed. Rules 1 through 20 are used for Triggers, Z-Wave Scenes and Follow-Me
Messages. Rules 21 through 40 are used for Z-Wave Scenes and for E-mail notification and are only accessible
through TotalConnect Service. Check with your Installer to see which options are available to you.
The following options are programmed in this section:
Programming Field
Rule 1 - 20:
Name:
Type:
Action:
Start Zone Type:
Stop Zone Type:
Start System Operation:
Stop System Operation:
Zone Number Operation:
Action
Select Rule 1 -20
Note: Rules 21-40 are only accessible through TotalConnect Service.
Name the device
Select the output type
Select the action required for the device
Select Zone Type to start event
Select Zone Type to stop event
Select System Operation to start event
Select System Operation to stop event
Select Zone Number to trigger event upon fault, trouble or alarm as selected.
Programming Rules
Ready To Arm
1. With the system in the disarmed state, select the “Automation”
icon from the Home Screen. The system displays the first
page of the Automation screen. Select the “” icon to
advance to the second page of the Automation screen.
12:35 PM
October 1, 2013
Mostly Sunny
Security
Automation
Video
News
Traffic
Notices
68 F
Feels Like 71
F
5-Day Forecast
5200-100-001-V0
2. Select the “Rules” button. The system displays the Rules
screen.
Ready To Arm
Scenes
Tools
Schedules
Garage door setup
Rules
5200-100-053-V0
Ready To Arm
Rules 1
New
New
Rules 3
Rules 4
New
New
Rules 5
Rules 6
New
New
Edit
3. Select a “Rules” key followed by the Edit button.
Note: Rules 21-40 are only accessible through TotalConnect
Service.
Rules 2
Delete
5200-100-059-V0
– 47 –
USER FUNCTIONS
Automation
Ready To Arm
123!@#
Q
W
E
A
Clear
R
T
Y
U
I
O
S
D
F
G
H
J
K
Z
X
C
V
B
N
M
abc...
P
L
4. Select the “Name” key and then enter up to 13 characters of
text on the displayed keyboard to assign a name to the Rule.
Note: Select the “ABC…” key to switch the keyboard between
upper/lower case or the “123!@#” key to switch to
numbers.
5 Once you are finished, select “Done”. The system returns to
the Rules screen.
Done
5200-100-058-V0
Ready To Arm
01
Name
Type
Disabled
Save
5200-100-060-V0
Ready To Arm
Name
01
Type
Action
Trigger Output
None
Start Zone Type
Stop Zone Type
Not Used
Not Used
Start System Operation
Stop System Operation
Not Used
Not Used
Save
5200-100-062-V0
6. Select the “Type” button. Dependent upon the features
programmed in your control, the system toggles between the
following Types:
Disabled
Trigger Output
Scene (displayed when Z-Wave has been enabled)
Email 1
The system displays several new programming fields,
dependent upon the Type that is selected.
If Scene was selected, refer to the Home Automation Guide
P/N 800-16091 for information.
7. Select “Action”. Dependent upon the Type selected
previously, the system scrolls between several options:
None
Permanent On
On for 2 sec
Pulsing
Send
Run Scene*
* If Scene was selected in step 6 refer to the Home Automation
Guide PN 800-16091 for information.
8. Select “Start Zone Type”. Use the “” “” buttons to scroll to
second and third page of zone type options. The system
displays the following options (dependent upon the Type that
was selected).
Not Used
Entry Exit 1
Entry Exit 2
Perimeter
Interior Follower
Day / Night
24 Hour Silent
24 Hour Audible
Silent Burglary
24 Hour Auxiliary
Interior With Delay
Fire No Verification
Carbon Monoxide
Trouble
No Response
Arm Stay
Arm Away
Disarm
Monitor
Resident Monitor
Resident Response General Monitor
General Response
Garage Door
Garage Monitor
– 48 –
USER FUNCTIONS
Automation
Ready To Arm
01
Name
Type
Action
Trigger Output
None
Start Zone Type
Stop Zone Type
Not Used
Not Used
Start System Operation
Stop System Operation
Not Used
Not Used
Save
5200-100-062-V0
9. Select “Stop Zone Type” The system displays the same
options as the previous step.
Note: If a Rule is being used to trigger a Z-Wave door lock, when
the system is Armed Stay or Armed Away, it is
recommended that “End of Exit Delay” be selected for
System Operation 1 or System Operation 2.
10. Select “Start System Operation”. Use the “” “” buttons to
scroll to second page of zone type options. The following
options are displayed:
Not Used
Arm Away
Any Burglary Alarm
Bell Timeout
Start of Entry Delay
Kissoff
System Low Battery
Duress Alarm
Arm Stay
Disarm
Any Fire Alarm
End of Exit Delay
Chime
Bypass
Reporter Failure
11. Select “Stop System Operation”. The system displays the
same options as step 10.
Ready To Arm
12. Select “Zone Number Operation”. The system toggles
between the following options:
Zone Number Operation
Not Used
Fault
Trouble
Alarm
Not Used
Save
5200-100-063-V0
Ready To Arm
13. Select the First, Second or Third “Start Zone” Select the Zone
from the list displayed by the system.
14. Select the First, Second or Third “Stop Zone” Select the Zone
from the list displayed by the system.
15. Select “Save” when programming is complete.
16. Select the “” button. The system returns to the Automation
programming screen.
Zone Number Operation
Fault
First Start Zone
Disabled
Second Start Zone
Disabled
Third Start Zone
Disabled
First Stop Zone
Disabled
Second Stop Zone
Disabled
Third Stop Zone
Disabled
Notes: 1. For Fault, the following zone types should not be used:
General Monitor, General Response, Resident
Monitor, and Resident Response.
2. When a zone has been deleted, please verify the
programming selection for Zone Number Operation.
If Trouble, Fault or Alarm is selected, the system displays
several new options. Proceed to Step 13.
Save
5200-100-064-V0
– 49 –
USER FUNCTIONS
Automation
Editing or Deleting Rules
Ready To Arm
Device 1
System Armed
Follow Me
Device 3
Device 4
New
New
Device 5
Device 6
New
New
1. At the Rules Programming Screen, select the Rule that you
wish to edit or delete.
Note: Rules 21-40 are only accessible through TotalConnect
Service.
2. To delete the rule, select the Delete button. To edit the rule
select the Edit button and proceed to step 3.
Device 2
New
Edit
Delete
5200-100-065-V0
Ready To Arm
Name
3. Select the field that you wish to edit and follow the steps as
outlined in the Programming Rules procedure.
01
System Armed
Type
Action
Message to phone 1
Send
Start Zone Type
Stop Zone Type
Not Used
Not Used
Start System Operation
Stop System Operation
Armed Stay
Disarm
Save
5200-100-066-V0
– 50 –
USER FUNCTIONS
Reminders
The Reminder Feature can be used to program/record reminders that can be displayed on the touch screen,
announced by the control.
Programming a Reminder
Ready To Arm
1. With the system in the disarmed state, select the “Tools” icon
from the second page of the Security Screen. The system
displays the Keypad screen.
Tools
Arm Away
Arm Stay
Settings
10:18 AM June 8, 2010
Delay
Back
5200-100-033-V0
Ready To Arm
Program the system
Enter Code:
Cancel
1
2
3
4
5
6
7
8
9
Clear
0
2. Enter your 4-digit Master User Code. The system displays the
Master User programming screen.
5200-100-035-V0
Ready To Arm
3. Select the “Reminders” icon. The system displays the
Reminders screen.
Users
Events
Test
Keypad
Date Time
Reminders
Slide Show
WiFi Config
Back
5200-100-036-V0
Ready To Arm
4. Select “Add New”. The system displays the Reminder
programming screen.
No items to display!
Add New
Play
Delete All
Save
5200-100-045-V0
– 51 –
USER FUNCTIONS
Reminders
Ready To Arm
Name
5. Select “Name”. Enter a name for the scheduled function on
the displayed keypad then select “Done”.
6. Select “Frequency” then select one of the following displayed
options:
None
Once
Daily
Weekday
Weekly
Monthly
Frequency
None
Voice
Acknowledge
No
No
Save
5200-100-068-V0
Ready To Arm
123!@#
Q
W
E
A
Clear
R
T
Y
U
I
O
S
D
F
G
H
J
K
Z
X
C
V
B
N
M
abc...
P
L
7. Program the following options based upon the Frequency
selected in step 6:
Once
Date/Start Time
Daily
Start Time
Weekday Start Time
Weekly
Day of the Week/Start Time
Monthly
Day of the Month/Start Time
Sunrise
Day of the Week/Start Time
Sunset
Day of the Week/Start Time
Done
5200-100-069-V0
Ready To Arm
Reminders 1
8. If a voice reminder is desired, select “Voice”. The system
toggles between “No” and “Yes”. If yes is selected, the record
reminders screen appears.
9. Select the “Record” button and record your reminder. When
you are finished select the “Stop” button followed by the “”
button. The system returns to the Reminder programming
screen.
Stopped
Record
Play
Delete
5200-100-070-V0
Ready To Arm
Name
Frequency
Walk Dog
Once
Note: For important reminders you should program the
“Acknowledge” option. When this option is selected, the
reminder will continue to play until it is acknowledged.
10. Select the “Acknowledge” option. The system toggles
between “No and “Yes”.
11. Select “Save” when all applicable options have been
programmed.
Date
January 1, 2011
Start Time
3:00 PM
Voice
Acknowledge
No
No
Save
7000-100-033-V0
– 52 –
USER FUNCTIONS
FUNCTIONS
Reminders
Editing a Reminder
Ready To Arm
Walk Dog
Edit
1. At the Reminders screen, select the reminder you wish to
edit.
2. Select the “Edit” button. The Reminder programming screen
will appear. Follow the steps as noted above in the
programming a Reminder section to edit and save your
changes.
- Daily
New
Delete
5200-100-072-V0
Deleting a Reminder
Ready To Arm
Walk Dog
Edit
1. At the Reminders screen, select the reminder you wish to
delete.
2. Select the “Delete” button. A confirmation screen will be
displayed. Select “Yes” to confirm the deletion.
3. Select the “” button. The system returns to the Master User
programming screen.
- Daily
New
Delete
5200-100-072-V0
– 53 –
USER FUNCTIONS
WiFi Configuration
View/Join Available WiFi Networks
Ready To Arm
1. At the Master User screen select the WiFi Config icon. The
system displays the WiFi options screen.
Users
Events
Test
Keypad
Date Time
Reminders
Slide Show
WiFi Config
Back
5200-100-036-V0
2. Select the “Scan Access Points” button to view the available
networks. The available networks are displayed. Use the
down arrow to scroll to the next page of options. Use the
arrow to return to the previous page.
Ready To Arm
Scan Access Points
Manual Configure AP
WPS
Press the WPS button on the access point, then press this WPS button.
Automatic Video Recovery
5200-100-073-V1
3. Select the desired Network and then select the “Edit” button.
The network information is displayed. If a password is
required, select the “Key” button and enter the password.
Ready To Arm
SSID = Vtek, RSSI = -62dbm
SSID = JimC, RSSI = -66dbm
SSID = Toms_net, RSSI = -86dbm
Edit
Scan
5200-100-074-V0
Ready To Arm
4. Select the “Join” button. A confirmation screen will be
displayed.
5. Select the “Save button, then select the “” button as
required to return to the Master User screen.
Name SSID
Toms_net
Security
Network Type
WPA1
Infrastructure
Key
****
Join
5200-100-075-V0
– 54 –
USER FUNCTIONS
WiFi Configuration
Manually Configure Access Point
Ready To Arm
1. At the Master User screen select the WiFi Config icon. The
system displays the WiFi options screen.
Users
Events
Test
Keypad
Date Time
Reminders
Slide Show
WiFi Config
Back
5200-100-036-V0
2. Select the “Manually Configure AP” button to view the
available networks. The WiFi enrollment screen is displayed.
Ready To Arm
Scan Access Points
Manual Configure AP
WPS
Press the WPS button on the access point, then press this WPS button.
Automatic Video Recovery
5200-100-073-V1
Ready To Arm
3. Select the “SSID Name” button and enter Network name on
the displayed keypad.
4. Select the “Security” button and select from “Open”, “WPA1,
“WPA2” and “WEP”. The network information is displayed. If
a password is required, select the “Key” button and enter the
password.
Name SSID
Toms_net
Security
Network Type
WPA1
Infrastructure
Key
Note: When configuring for WEP encryption key on the access point,
always use hexa-decimal type as the input method on the panel.
The input key should contain characters such as 0-9 and A-F.
****
Join
5200-100-075-V0
4. Select the “Join” button. A confirmation screen will be
displayed. Select “OK”, then select “Save” to confirm the
selection.
5. Select the “” button as required to return to the Master User
screen.
– 55 –
USER FUNCTIONS
WiFi Configuration
Join a WPS (WiFi Protected Setup) Network
Ready To Arm
1. At the Master User screen select the WiFi Config icon. The
system displays the WiFi options screen.
Users
Events
Test
Keypad
Date Time
Reminders
Slide Show
WiFi Config
Back
5200-100-036-V0
Ready To Arm
Scan Access Points
Manual Configure AP
WPS
Press the WPS button on the access point, then press this WPS button.
Automatic Video Recovery
5200-100-073-V1
Note: For WPS operation, press the WPS button on the access
point (router) first. Then press the WPS button on the
control.
2. Select the “WPS” button. The system displays “Please Standby for WPS Operation…”
3. If the operation is successful, the system displays “Device
has been successfully added to the network.” If the operation
is unsuccessful the system displays “Failed Operation.
Device not added to the network.”
4. Select “OK”.
Enrolling/Syncing Auxiliary Keypads
A router is required if you are using an approved mobile device as an Auxilary Keypad. The router must be
powered on and connected for WiFi operation to occur.
The LYNX Touch will support up to four Mobile Devices (or tablets) that can be used as Auxiliary Keypads. A
WiFi communication device and router are required. The “Keypad” button is used to enroll/sync the mobile
device with the control. Refer to the documentation provided with the device to enroll/sync the keypad.
Viewing or Deleting Enrolled Keypads
Ready To Arm
1. At the Master User screen select the Keypad icon. The
system displays the WiFi devices screen.
Users
Events
Test
Keypad
Date Time
Reminders
Slide Show
WiFi Config
Back
5200-100-036-V0
Ready To Arm
2. To delete a mobile device (auxiliary keypad) select the
keypad to be deleted.
3. Select the “Delete” button.
Keypad 120 MAC ID: XX:XX:XX:XX:XX
Note: Defaulting the system
associated keypads.
Keypad 121 MAC ID: XX:XX:XX:XX:XX
Keypad 122 MAC ID: XX:XX:XX:XX:XX
Keypad 123 MAC ID: XX:XX:XX:XX:XX
Delete
5200-100-077-V0
– 56 –
will not
automatically delete any
USER FUNCTIONS
Video Camera Control Feature
The LYNX Touch L7000 supports up to 20 video cameras and provides the capability to view live video from a
maximum of four cameras. The installation of a WiFi Communications module and a WiFi internet connection
are required. Check with your installer to see if this features is available.
Selecting a Camera
Ready To Arm
12:35
1. With the system in the disarmed or armed state, select the
Video icon. The system advances to Cameras screen
PM
January 12, 2010
Mostly Sunny
Security
Automation
Video
News
Traffic
Notes
68 F
Feels Like 71
F
5-Day Forecast
5100-100-001-V2
Ready To Arm
2.
Cameras
Name
IP
MAC
Back
Scan
If no cameras have been discovered or if a list of discovered
cameras is invalid, a Camera scan will start automatically.
Note: The latter can occur if a WiFi connection is lost.
2. A Manual scan can be performed by selecting the “Scan”
button. When the scan is complete the available cameras
will be displayed.
Note: Up to 20 cameras will be viewable during scanning/
enrollment however, only four will appear on each page.
5200-100-010-V0
Ready To Arm
4. Select the desired camera(s) (up to four) from the list by
“tapping” once. If applicable select the “” button to view
additional pages of available cameras. Select the “” button
to return to the previous page of the list.
Cameras
Name
IP
MAC
Name
10.10.150.176
00:C0:02:7B:67:E4
Name
10.10.150.159
00:C0:02:8F:60:4E
Name
10.10.150.158
00:0E:8F:79:C7:EF
Name
10.10.150.67
00:0E:8F:79:CB:C2
Back
Scan
5200-100-007-V1
Ready To Arm
Cameras
Name
IP
MAC
Pool
10.10.150.176
00:C0:02:7B:67:E4
Patio
10.10.150.159
00:C0:02:8F:60:4E
Den
10.10.150.158
00:0E:8F:79:C7:EF
Living Room
10.10.150.67
00:0E:8F:79:CB:C2
Back
Scan
7000-100-019-V1
Ready To Arm
POOL
DEN
PATIO
1
2
3
4
5. The selected camera(s) are highlighted. To edit the camera
name go to step 6 OR to save the camera go to step 9.
6. To edit the camera name select the highlighted camera again
and then select the edit button.
Note: To de-select a camera “tap” the highlighted camera two
times.
7. Select the “Clear” button on displayed keypad, then enter the
deisred text.
8. Select “Done”.
9. Select the “Back” button.
10. The system displays video from the selected camera.
11. To select a different camera, select the camera button then
tap the selected camera two times and repeat steps 4 to 9 as
applicable.
12. Refer to the Video Camera Controls table for information
regarding the Video Function buttons. The available controls
are dependent upon the cameras that have been installed
and selected.
LIVING ROOM
7000-100-018-V0
– 57 –
USER FUNCTIONS
Video Camera Control Feature
Video Camera Reset
In the event that video streaming is lost, freezes or becomes pixelated the control can automatically or manually
reset the video depending on the option that is selected. The system is defaulted to automatically recover within
approximately 1 minute after communication has been restored.
Reset Video Cameras
Ready To Arm
1. At the Master User screen select the WiFi Config icon. The
system displays the WiFi options screen. The enabled recover
mode will be displayed.
Users
Events
Test
Keypad
Date Time
Reminders
Slide Show
WiFi Config
Back
5200-100-036-V0
2. Selecting Automatic Video Recovery button will enable the
manual feature or selecting the Manual Video Recovery
button will enable the Automatic feature. The display toggles
to display the selected mode and saves the entry.
Ready To Arm
Scan Access Points
Manual Configure AP
WPS
Press the WPS button on the access point, then press this WPS button.
Manual Video Recovery
5200-100-073-V1
Ready To Arm
Double Tap to Restore Video
DEN
PATIO
1
2
3
4
• If Automatic Video Recovery is enabled with TotalConnect
services, “Wait for Automatic Video Restore” will be displayed in a
blue band. The video recovery will be automatically recovered
within approximately 1 minute after the camera restores
communication.
• If Automatic Video Recovery is enabled without TotalConnect
services, the video recovery will begin automatically after the
camera restores communication.
• If Automatic Video Recovery is enabled the video can be
recovered manually.
• If Manual Video Recovery is enabled, “Double tap to restore
video” will be displayed in a yellow band. The video recovery will
begin automatically after the camera restores communication
• If the control is in the Armed Away state the camera must be
recovered via the manual mode.
3. If Automatic Video Recovery is enabled, wait for the camera to
automatically recover. If Manual Video Recovery is enabled,
tap the video dispay two times to restore video.
Note: If the control is in the Armed Away state the camera must
be recovered via the manual mode.
4. Upon recovery the video display will return to normal and the
camera name will be displayed in a green band.
LIVING ROOM
7000-100-018-V0
– 58 –
USER FUNCTIONS
Video Camera Control Feature
Video Camera Controls
The controls that are available are dependent upon the cameras that are installed with your system. Only those
controls that are applicable to the specific camera will be displayed.
To control a camera:
To view/control a single camera:
To position a pan/tilt camera:
Tap one time on the video display from the camera you wish to control. The
LYNX Touch displays the camera controls that are avaiable for the selected
camera.
Tap two times on the video display from the camera you wish to control. The
LYNX Touch displays a full screen view of the video and the camera
controls that are avaiable for the selected camera. Tap the video display two
times again to return to multiple camera viewing.
Pan/tilt cameras can be positioned using the arrow or home button OR by
sweeping a finger across the screen, horizontally, vertically or diagonally to
drive the camera in that direction.
Button
1
2
3
4
1
2
3
4
Function
Video Camera Control
Button operation is dependent upon the features available in the camera that is installed/selected (i.e.;
pan & tilt and auxiliary LED light). Only the buttons that are applicable for the selected camera are
displayed.
Camera "Home" position - The camera's home position is centered in its vertical and horizontal axis.
• When a camera has been moved to other than the home position, after 5 minutes of no movement
the camera will always return to the home position.
Notes
• Additional features can be programmed via TotalConnect 2.0. Check with your installer to see
which features are available.
• In the event that video is lost, frozen or is pixelated and does not automatically reset, tap the
display two times to manually restore the video.
Preset buttons 1, 2, 3, 4 – These buttons are used to quickly drive the camera to a preset watch area.
(Up to 4 preset watch areas can be set.) Select the button to go to the preset watch area. To set a
preset watch area, use the arrow buttons to drive the camera to the desired area. Then tap the desired
1, 2, 3, or 4 button three times. The selected button will be highlighted (for around 5 seconds)
confirming that the preset is saved.
Arrow buttons – Used to position a PT (pan & tilt) camera. Select to incrementally position a pan & tilt
camera (i.e; iPCAM-PT) in a vertical or horizontal direction.
Center home button – Click to drive the camera to its home position.
Light – Used to toggle on or off the camera's auxiliary lighting LEDs. Depending on the ambient low
light conditions, the auxiliary lighting can improve video quality up to 15 feet.
Auto pan – Causes the camera to swing through its entire horizontal range. At the end of the panning
motion, the camera will return to the starting position. After 5 minutes of no movement the camera will
always return to the home position.
Video Camera – When selected, the panel displays a list of available video cameras.
Return/Home – Returns the control panel to the panel’s Home Screen
Video Camera Indicators
Displayed Text
Band
Meaning
“Name” OR Camera information
Green
Normal operation, selected camera
“Name” OR Camera information
Gray
Normal operation, unselected camera
“Wait for Automatic Video Restore…”
Blue
Video restoration will begin automatically when communication is restored.
Yellow
Video restoration requires user to tap the display two times. Video will begin
when communication is restored.
“Video No Longer Available”
Red
Comunication with camera has been lost
Date & Time
Black
Displayed if programmed
“Double Tap to Restore Video”
– 59 –
USER FUNCTIONS
Two-Way Voice Feature (Alarm Audio Verification)
This feature allows an operator at the Central Station to listen, talk to or conduct a two-way conversation with
an individual(s) at your location. It also assists the operator in gathering information about the nature and
location of the alarm that may be helpful in responding to police and/or fire departments. All LYNX Touch
control panels are capable of supporting the Two-Way Voice feature. The LYNX Touch does not make system
announcements when the Two-Way voice feature is active.
If a WiFi connection is being used for Two-Way Voice (AAV), sufficient bandwidth must be available.
• AAV requires a continuous WiFi upload/download bandwidth of 90kbps for proper operation.
• WiFi bandwidth less than 90kbps may result in degraded performance.
Fire and CO alarms will prevent the LYNX Touch from starting an Two-Way Voice session. A new Fire or
CO alarm will end a Two-Way Voice session that is in progress.
If the Two-way Voice Feature has been programmed and an alarm condition is detected, the system sends an
alarm message to the central station. After acknowledgement is received, a “listen in to follow” message is sent
to the central station. In response to this message, the central station operator can enter commands that allow
initiation of a 5-minute voice session.
When activated the Two-Way Voice (AAV) feature enters the “Listen Mode” and sirens and keypad sounds are
discontinued. The Central Station operator begins the session, which lasts 5 minutes, and may be extended 5
minutes, without changing the operating mode. If a subsequent security zone is violated during a voice session,
the session will continue and the alarm will be buffered. If a fire zone is violated during a voice session, the
system will terminate the session and process the alarm. The Two-Way Voice modes are described as follows:
Listen Mode: Enables one-way audio from the violated premises to the central station. The Listen Mode is the
start up default mode of the voice feature and allows the operator to listen through the LYNX Touch
microphone.
Talk Mode: Enables one-way voice communication from the Central Sation to the violated premises, and
allows the operator to communicate through the built-in speaker on the LYNX Touch. In this mode the Home
Key will blink Green.
VOX (Voice) Mode: Enables two-way voice communications between the Central Station and the violated
premises via the built-in speaker and microphone on the LYNX Touch. In this mode the Home Key will blink
Green.
During the voice session, the the Home Key will blink Green in the Talk and VOX Modes but not during Listen
Mode.
– 60 –
USER FUNCTIONS
Remote Services
Your security system may be capable of providing a series of web-based services that allow you to communicate
with your security system remotely in a number of ways. These features are enabled through Total Connect
Service and provide the ability to:
• Access to your security system from a computer via website (Remote Access Feature)
• Receive e-mail and text message notification of system events (Multi-Mode Feature)
• Perform system functions and receive confirmations using text messages (SMS Feature)
• Program/operate home automation devices.
Ask you installer if your system employs a remote services capable device.
– 61 –
USER FUNCTIONS
Slide Show
The LYNX Touch features a Slide Show/Screen Saver feature. The feature allows images to be displayed on the
touch screen when it is not in use. Connection to Total Connect Service is required in order for your installer to
upload images to your panel. For more information about this option, speak to your installer.
Activating the Slide Show
Ready To Arm
1. With the system in the disarmed state, select the “Tools” icon
from the second page of the Security Screen. The system
displays the Keypad screen.
Tools
Arm Away
Arm Stay
Settings
10:18 AM June 8, 2010
Delay
Back
5200-100-033-V0
Ready To Arm
Program the system
Enter Code:
Cancel
1
2
3
4
5
6
7
8
9
Clear
0
2. Enter your 4-digit Master User Code. The system displays the
Master User programming screen.
5200-100-035-V0
Ready To Arm
3. Select the “Slide Show” icon. The system displays the first
Slide Show screen.
Users
Events
Test
Keypad
Date Time
Reminders
Slide Show
WiFi Config
Back
5200-100-036-V0
Ready To Arm
1
Slide Interval
5 Seconds
2
Slide After
Disabled
Delete All
Save
5200-100-086-V0
4. Select the “Slide Show” icons that you do not wish to display
or select “Delete All”. Use the “” “” buttons to scroll to
second and subsequent pages of screens.
5. Select the “Slide Interval” button. The system scrolls through
the following options:
Slide Interval 5 Seconds
Slide Interval 10 Seconds
Slide Interval 15 Seconds
Slide Interval 20 Seconds
6. Select the “Slide After Disabled” button. The system scrolls
through the following options:
Slide After Disabled (disables the Slide Show)
Slide After 30 Seconds
Slide After 2 Minutes
Slide After 10 Minutes
Slide After 30 Minutes
7. Once selections are complete, select the “Save” button.
– 62 –
SUMMARY OF AUDIBLE & VISUAL NOTIFICATIONS
NOTIFICATIONS
Audible Soundings
SOUND
INTERRUPTED
CAUSE
FIRE ALARM (3 beeps)
OR
CARBON MONOXIDE ALARM (4 beeps)
CONTINUOUS
BURGLARY/AUDIBLE EMERGENCY ALARM
ONE SHORT BEEP
(not repeated)
a. SYSTEM DISARM
b. SYSTEM ARMING ATTEMPT WITH AN
OPEN ZONE.
c. BYPASS VERIFY
a. SYSTEM IS IN TEST MODE
b. LOW BATTERY AT A TRANSMITTER
c. SYSTEM LOW BATTERY
d. FAIL TO COMMUNICATE
ARM AWAY
ONE SHORT BEEP
(once every 45 secs)
TWO SHORT
BEEPS
THREE SHORT
BEEPS
RAPID BEEPING
SLOW BEEPING
ANNOUNCEMENT*
fire alarm + zone voice descriptor
OR
Carbon monoxide alarm + zone voice descriptor
(Voice descriptor is interlaced with the sounder and sounds every 45
seconds)
alarm + zone voice descriptor
(Voice descriptor is interlaced with the sounder and sounds every 45
seconds)
a. disarmed–ready to arm
b. disarmed–not ready to arm
c. zones bypassed
a. no announcement
b. low battery + zone voice descriptor
c. system low battery
d. check system
armed away [instant] – exit now
a. ARM STAY OR INSTANT
b. ZONE OPENED WHILE SYSTEM IS IN
CHIME MODE.
a. TROUBLE
b. MEMORY OF ALARM
a. ENTRY DELAY WARNING
b. EXIT DELAY WARNING
a. armed stay [instant] – exit now
b. zone voice descriptor
a. fault + zone voice descriptor
b. fire alarm or alarm + zone voice descriptor
a. disarm system now
b. armed [away] [instant] – exit now
Additional Announcements:
The system will announce the following primary messages, depending on the system’s status at the time:
•
•
•
Disarmed–Ready to Arm [check system][chime]
Disarmed [not ready to arm][chime]
Armed [away] [stay] [instant] [check system] [exit now]
– 63 –
SUMMARY OF AUDIBLE & VISUAL NOTIFICATIONS
System Displays
The following icons will be displayed on the Security Screen along with specific zone status information (if
applicable) to indicate system status.
DISPLAY
DEFINITION
DISPLAY
DEFINITION
DISPLAY
DEFINITION
AC Loss
Door Open
Reporter
Failure
Alarm
(intrusion)
Window Open
Cover
Tamper
Armed Away
Exit Active
Trouble
Armed Stay
Fire
OR
Heat Sensor
Flood
90 RF Jam
Battery Low
Automation
(Z-Wave Node
Failed)
Check Zones
Glass Break
WiFi source
present
CO Alarm
Medical Alarm
No WiFi source
Disarmed Not
Ready to Arm
Motion
Fault *
Garage Door
Disarmed
Ready to Arm
Temperature
103 Comm.
Trouble
Zone Status Icons
The following icons may be displayed on the Zone Status screen.
DEFINITION
DEFINITION
ICON
ICON
Alarm
Trouble (red)
Fault (Yellow)
Bypass
ICON
DEFINITION
Ready
Key/LED Status
Home key
Panic key
Internal LED indicates the following:
Green = System is ready to be armed
Red = System is armed
Green Blinking = System is disarmed, and not ready to be armed (a fault or alarm exists)
Red Steady = System is Armed
Red Blinking = System is in Alarm
Red/Green Blinking alternately = System programming mode OR Two-way voice mode is active
Internal Red LED is lit in normal conditions
Note: When the system is armed, the Home Key LED is lit Red.
– 64 –
SYSTEM FUNCTIONS
Testing the System (to be conducted weekly)
Test Modes
The Test icon provides access to the Walk Test and Reboot functions. The Walk Test mode allows each
protection point to be checked for proper operation. When the Walk Test mode is active, the control sounds a
single beep every 30 seconds as a reminder that the system is in the Test mode. The Reboot feature allows you
to reboot the system if required.
NOTE: An alarm message will not be sent to your alarm monitoring company during these tests.
Entering Test Mode
Disarm the system and close all protected windows, doors, etc. The “Ready” indicator should be lit.
Testing or Rebooting the System
Ready To Arm
1. With the system in the disarmed state, select the “Tools” icon
from the second page of the Security Screen. The system
displays the Keypad screen.
Tools
Arm Away
Arm Stay
Settings
10:18 AM June 8, 2010
Delay
Back
5200-100-033-V0
Ready To Arm
Program the system
Enter Code:
Cancel
1
2
3
4
5
6
7
8
9
Clear
0
2. Enter your 4-digit Master User Code. The system displays the
Master User programming screen.
5200-100-035-V0
Ready To Arm
3. Select the “Test” icon. The system displays the Test screen.
Users
Events
Test
Keypad
Date Time
Reminders
Slide Show
WiFi Config
Back
5200-100-036-V0
– 65 –
SYSTEM FUNCTIONS
Testing the System (to be conducted weekly)
Ready To Arm
Prod. Id. : XXXX Sw. Rev.: XX.XX
CRC Number: XXXX
RF Version Number: XXXXXX
WiFi Ver: X.X.X
Walk Test
Comm. Test
Reboot
Back
7000-100-028-V0
4. Select the “Walk Test”, “Comm. Test” or “Reboot” icon. If Walk
Test is selected proceed to Step 5. If Comm. Test is selected
proceed to Step 6. If Reboot is selected proceed to Step 7.
5. “Walk Test…” is displayed on the system status bar and the
control sounds a single beep every 30 seconds. Fault each
zone as described below.
6. The system will advance to the Communications Test Screen.
Refer to the Communications Test paragraph.
7. The system will reboot itself.
8. After the reboot sequence is completed, conduct a Walk Test
to verify that all transmitters are operational in the system.
Walk Test
FAULT ZONES. Open each protected door and window in turn and listen for three beeps from the control,
followed by the zone’s Voice Descriptor, if it is programmed. Identification of each faulted protection point
should appear on the display. The display will clear when the door or window is closed.
Walk in front of any interior motion detectors (if used) and listen for three beeps and/or voice descriptors, if
programmed. The identification of the detector should appear on the display when it is activated, and its voice
descriptor will be announced (if programmed). The display will clear when no motion is detected. Note that if
wireless motion detectors are used, in order to conserve battery life, there is a 3-minute delay between
activations.
To test all smoke detectors, follow the manufacturer's instructions. The identification of each detector should
appear on the display when each is activated.
If a problem is experienced with any protection point (no confirming sounds, no display), notify your service
company.
When all protection points have been checked and are intact (closed), there should be no zone identification
numbers displayed on the touch screen.
Test Communications
Depending upon the Communication device that installed in your system the following options may be
displayed. Select the desired option to send a test alarm to the Central Station.
• Test Ethernet
If the test is successful, the System displays: Service OK
• Send Any
•
Send GSM Message
• Send Ethernet Message
If the test is successful, the System displays: Test Message Sent
If the test is not successful, the System displays: Test Message Failed – Not Registered!
Exiting Test Mode
When testing is completed, exit the Walk Test, Dialer Test or Comm. Test mode by selecting the Home key and
entering the Master User Code (if required).
.
NOTE: If the Walk Test mode is inadvertently left active, it automatically turns off after 4 hours. The Dialer Test mode will remain
active until exited via an Off sequence.
LYNX Touch Exit/Entry Delay Times
The LYNX Touch will send an event code to the Central Station after entering and after exiting from Test
mode.
– 66 –
SYSTEM FUNCTIONS
Maintaining your system
The components of your security system are designed to be as maintenance-free as possible. To make sure that
your system is in working condition, do the following:
1. Test your system weekly (see the TESTING THE SYSTEM section).
2. Test your system after any alarm occurs (see the TESTING THE SYSTEM section).
3. Clean the touch screen weekly.
Routine Care
• Treat the components of your security system as you would any other electrical equipment. Do not slam
sensor-protected doors or windows.
• Keep dust from accumulating on the touch screen and all protective sensors, particularly on motion sensors
and smoke detectors.
• The touch screen and sensors should be cleaned carefully with a dry soft cloth. Do not spray water or any
other fluid on the units.
Cleaning the Touch screen
Ready To Arm
1. With the system in the disarmed or armed state, select the
“Settings” icon from the second page of the Security Screen.
The system displays the Settings” screen.
Tools
Arm Away
Delay
Arm Stay
Settings
10:18 AM June 8, 2010
Back
5200-100-033-V0
Ready To Arm
Brightness
Contrast
Volume
Clean
Voice
Ringer
Chime
Save
5200-100-034-V0
2. Select the “Clean” icon. The touch screen becomes inactive
for a period of 15 seconds. A box displays “Please Use A
Damp, Soft Cloth Touch Screen Will Be Disabled For 15
Seconds” and the time will count down.
3. After 15 seconds the screen returns to the settings screen and
becomes active.
Note: If any user notification events occur while the screen
cleaning mode is active and the system is armed, the
mode will be canceled and the system will operate
normally. If certain user notification events occur (i.e.;
motion or silent alarm) while the screen cleaning mode is
active and the system is disarmed the mode will not be
canceled.
Low Battery Conditions in Wireless Sensors
Each wireless sensor in your system has an internal battery. The system detects low battery conditions in
wireless sensors, including smoke detectors, personal emergency transmitter, and the portable wireless keypad,
and displays a “Battery Low” message on the touch screen, which also beeps. A low battery in a wireless keypad
is detected as soon as one of its keys is pressed. In addition, a wireless smoke detector with a low battery also
emits a "chirp" sound approximately once every 20–30 seconds, identifying itself as the smoke detector with the
weak battery.
NOTE: A low battery message means that battery replacement in the indicated sensor(s) is due within 30 days. In the meantime,
a sensor with a low battery is still operational.
To silence Low Battery Warning Tones, enter an Off sequence. The low battery message display will remain on
as a reminder. When you replace the weak battery with a fresh one, the sensor will send a "good battery" signal
to the control when the sensor is activated (opening/closing of door, window, etc.). To clear the “Low Battery”
message, enter an Off sequence.
– 67 –
SYSTEM FUNCTIONS
Maintaining your system
When replacing batteries, use only those recommended by your installer.
Alkaline batteries provide a minimum of 1 year of operation, and in most units and applications, provide 2–4 years of service. 3volt lithium batteries may provide from 4-7 years of operation. Actual battery life will depend on the environment in which the
sensor is used, the number of signals that the transmitter in the sensor has had to send, and the specific type of sensor. Factors
such as humidity, high or low temperatures, and large swings in temperature may all lead to the reduction of actual battery life in
an installation.
Changing the LYNX Touch Series System Battery
In the event of an AC power loss, the LYNX Touch Series is powered by a rechargeable, nickel-metal hydride
battery pack. The battery pack should be replaced when a “Battery Low” message with no zone number is
displayed.
NOTE: The battery pack (P/N LYNXRCHKIT-SC or LYNXRCHKIT-SHA) should be changed every four years and must be
replaced by a qualified service technician.
Following battery pack replacement, rechargeable batteries may take up to 48 hours to charge. The “Battery
Low” message may be displayed after one minute, however it should clear within 4 hours or by entering Test
Mode.
– 68 –
FIRE/CO ALARM SYSTEM (If Installed)
General Information
UL
LYNX Touch is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N
LYNXRCHKIT-SHA) is installed.
General
Your fire alarm system (if installed) is active 24 hours a day, providing continuous protection. In the event of an
emergency, the installed smoke, heat and/or carbon monoxide detectors will automatically activate your
security system, triggering a loud, intermittent sound from the touch screen. The sound will be interlaced with
the voice descriptor, sounding every 15 seconds. A “FIRE” or “CO” message will appear at your touch screen and
remain on until you silence and clear the alarm display.
In Case of Fire
1. Should you become aware of a fire emergency before your detectors sense the problem, go to the LYNX Touch
and press and hold the panic button and then select the Fire icon. The alarm will sound and an alarm will be
transmitted to the central station.
2. Evacuate all occupants from the premises.
3. If flames and/or smoke are present, leave the premises and notify your local Fire Department immediately.
4. If no flames or smoke are apparent, investigate the cause of the alarm. The zone number of the zone(s) in an
alarm condition will appear at the touch screen.
In Case of Carbon Monoxide Alarm
1. If a high level of carbon monoxide is detected you should evacuate all occupants from the premises and
immediately move to a spot where fresh air is available, preferably outdoors.
2. From a safe area, contact your security service provider for further instructions.
Silencing a Fire/Carbon Monoxide Alarm
1. Silence the alarm by entering an OFF sequence.
2. To clear the alarm, enter a second OFF sequence.
3 If the touch screen indicates a trouble condition after the second OFF sequence, check that smoke detectors are
not responding to smoke- or heat-producing objects in their vicinity. Should this be the case, eliminate the source
of heat or smoke.
4. If this does not remedy the problem, there may still be smoke in the detector. Clear it by fanning the detector for
about 30 seconds.
5. When the problem has been corrected, clear the display by entering another OFF sequence.
– 69 –
FIRE/CO ALARM SYSTEM
National Fire Protection Association Smoke Detector Recommendations
UL
LYNX Touch is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N
LYNXRCHKIT-SHA) is installed.
With regard to the number and placement of smoke and heat detectors, we subscribe to the recommendations
contained in the National Fire Protection Association's (NFPA) Standard #72 noted below.
Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and
areas of the household. The equipment should be installed as follows: A smoke detector installed outside of each
separate sleeping area, in the immediate vicinity of the bedrooms and on each additional story of the family
living unit, including basements and excluding crawl spaces and unfinished attics.
In addition, the NFPA recommends that you install heat or smoke detectors in the living room, dining room,
bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached
garages.
KITCHEN
DINING
BEDROOM BEDROOM
TV ROOM
KITCHEN
DINING
BDRM
LIVING ROOM
BDRM
BEDROOM
BEDROOM
LIVING ROOM
Smoke Detectors for Minimum Protection
Smoke Detectors for Additional Protection
Heat-Activated Detectors
BEDROOM
BEDROOM
TO
BR
BEDROOM
KTCHN
LVNG RM
.
CLOSED
DOOR
GARAGE
BASEMENT
floor_plan-001-V1
– 70 –
FIRE/CO ALARM SYSTEM
Emergency Evacuation
UL
LYNX Touch is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N
LYNXRCHKIT-SHA) is installed.
Establish and regularly practice a plan of escape in the event of fire. The following steps are recommended by
the National Fire Protection Association:
1. Position your detector or your interior and/or exterior sounders so
that they can be heard by all occupants.
3. Sketch a floor plan of the building. Show windows, doors, stairs and
rooftops that can be used to escape. Indicate escape routes for each
room. Keep these routes free from obstruction and post copies of the
escape routes in every room.
4. Assure that all bedroom doors are shut while you are asleep. This
will prevent deadly smoke from entering while you escape.
5. Try the door. If the door is hot, check your alternate escape route. If
the door is cool, open it cautiously. Be prepared to slam the door if
smoke or heat rushes in.
6. When smoke is present, crawl on the ground. Do not walk upright,
since smoke rises and may overcome you. Clearer air is near the
floor.
PORCH
2. Determine two means of escape from each room. One path of escape
should lead to the door that permits normal exit from the building.
The other should be an alternative escape, such as a window, should
your path to that door be unpassable. Station an escape ladder at
such windows if there is a long drop to the ground.
OM
ET
RO
OS
D
L
C
BE
DR
BE
TH
BA
M
OO
DR
E
B
2ND FLOOR
N
HE
TC
I
K
BACK DOOR
M
OO
DR
E
B
M
OO
TH
DR
BA
E
B
1ST FLOOR
•
•
BACK
7. Escape quickly; don't panic.
8. Establish a place outdoors, away from your house, where everyone
can meet and then take steps to contact the authorities and account
for those missing. Choose someone to assure that nobody returns to
the house — many die going back.
•
FRONT
emerevac
– 71 –
REGULATORY AGENCY STATEMENTS
Federal Communications Commission (FCC) Part 15
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized
changes or modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
•
•
•
•
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Industry Canada (IC)
This device complies with Part 15 of FCC Rules and RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions
suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les interferences
causant une reception indésirable.
RF Exposure Warning
!
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 in (20 cm) from
all persons and must notbe co-located or operated in conjunction with any other transmitter except in accordance with
FCC multi-transmitter product procedures.
Mise en Garde
Exposition aux Frequences Radio: L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de
séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.
– 72 –
WARNING!
THE LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire
or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for
a variety of reasons. For example:
• Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor
or disconnect an alarm warning device.
• Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work
without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not
put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however
briefly.
• Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if
the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the
path.
• A user may not be able to reach a panic or emergency button quickly enough.
• While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not
activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by
the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this
System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke
detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs,
or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or
building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors
have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not
always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping
gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson.
Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as
anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death.
• Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their
installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple
beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot
detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or
windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of
the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature;
however, as the ambient temperature of protected area approaches the temperature range of 90° to 105°F, the detection
performance can decrease.
• Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the
other side of closed or partly open doors. If warning devices sound on a different level of the residence from the
bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not
hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic.
Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers.
• Communication paths needed to transmit alarm signals from a premises to a central monitoring station may be out of
service or temporarily out of service. Communication paths are also subject to compromise by sophisticated intruders.
• Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect
themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond
appropriately.
• This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to
last as long as 10 years, the electronic components could fail at any time.
The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance.
This alarm system should be tested weekly to make sure all sensors and transmitters are working properly.
Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for
insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and
continue to insure their lives and property.
We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved
ones to learn about these developments.
– 73 –
SERVICING INFORMATION
Your local Honeywell dealer is the person best qualified to service your alarm system. Arranging some
kind of regular service program with him is advisable.
Your local Honeywell dealer is:
Name:
Address:
Phone:
– 74 –
OWNER'S INSURANCE PREMIUM CREDIT REQUEST
This form should be completed and forwarded to your homeowner's insurance carrier for possible premium credit.
A. GENERAL INFORMATION:
Insured's Name and Address:
Insurance Company:
Policy No.:
LYNX Touch Series __________________________________________________
Type of Alarm:
Burglary
Fire
Installed by:
Other
Both
Serviced by:
Name
Name
Address
Address
B. NOTIFIES (Insert B = Burglary, F = Fire)
Local Sounding Device
Central Station
Police Dept.
Fire Dept.
Name:________________________________________________________________________________
Address:
Phone:
C. POWERED BY: A.C. With Rechargeable Power Supply
D. TESTING:
Quarterly
Monthly
Weekly
(continued on other side)
– 75 –
Other
OWNER'S INSURANCE PREMIUM CREDIT REQUEST (cont.)
E. SMOKE DETECTOR LOCATIONS
Furnace Room
Kitchen
Bedrooms
Attic
Basement
Living Room
Dining Room
Hall
All Exterior Doors
F. BURGLARY DETECTING DEVICE LOCATIONS:
Front Door
Basement Door
Rear Door
1st Floor Windows
All Windows
Interior Locations
All Accessible Openings, Including Skylights, Air Conditioners and Vents
G. ADDITIONAL PERTINENT INFORMATION:
Signature:
Date:
– 76 –
– INDEX –
5-Day Forecast .........................................................13
Exit/entry delays ....................................................... 7
A
Alarm cancelled ....................................................7, 24
Alarm exit error .......................................................24
Alarm reporting delay ...............................................7
Alarms ........................................................................6
Arm night .................................................................19
Armed indicator .......................................................23
Arrow buttons ..........................................................59
Audible emergency/audible alarm ..........................30
Auto pan ...................................................................59
Auto stay arming feature ........................................18
Auto stay feature .......................................................7
Automation .........................................................13, 44
Auxiliary keypads ....................................................56
Away mode .......................................... 6, 8, 20, 23, 24
F
False alarm prevention features .............................. 7
False alarms ........................................................ 7, 24
Features ..................................................................... 5
Fire alarm .................................................... 11, 27, 30
Fire alarm system ................................................... 69
Fire protection ........................................................... 6
B
Battery ........................... 12, 63, 66, 67, 68, 69, 70, 71
Battery conditions ....................................................67
Battery low ...............................................................68
Battery pack .............................................................68
Burglary protection ................................................5, 6
Bypass a zone .............................................................8
Bypassing protection zones .................... 6, 28, 29, 33
L
LCD display ............................................................. 13
Light ......................................................................... 59
Liquid crystal display .............................................. 13
Listen mode .............................................................. 60
Location .................................................................... 13
G
Guest code .............................................. 17, 18, 20, 33
H
Home key ................................................................. 16
Home screen....................................................... 10, 13
Home” (cancel) key .................................................. 13
M
Manually configure access point ............................ 55
Master menu ............................................................ 15
Master user .......................................................... 6, 33
Master user code ...... 14, 15, 33, 35, 37, 41, 51, 62, 65
Memory of alarm ..................................................... 63
Menu......................................................................... 13
Menu screens ........................................................... 14
Message center .............................................. 5, 10, 38
Microphone .............................................................. 38
Mobile devices .......................................................... 56
Multi-mode feature .................................................. 61
C
Camera .....................................................................57
Camera "home" position ..........................................59
Central monitoring station..................................6, 73
Checking system status .............................................8
Chime mode ............................................... 6, 8, 10, 31
Cleaning the touchscreen ........................................67
Clear bypasses..........................................................29
Clock/calendar ....................................................41, 42
Control a camera ......................................................59
D
Delete” button ............................................. 46, 53, 56
Device activation ........................................................5
Devices ....................................................... 2, 5, 20, 73
Dialer test .................................................................66
Disarm ......... 6, 7, 8, 17, 18, 20, 23, 24, 25, 26, 33, 63
Disarming the system ..............................................26
Duress code...............................................................33
N
Navigation keys ....................................................... 13
News ......................................................................... 13
Night stay mode....................................................... 18
No delay ................................................................... 23
Notices ...................................................................... 13
P
Panic key ........................................................ 5, 30, 69
Personal emergency/aux. Alarm ............................. 30
Position a pan/tilt camera ....................................... 59
Preset buttons .......................................................... 59
E
Edit button .................................................. 46, 53, 54
E-mail events .....................................................44, 47
Entering test mode ..................................................65
Entry delay ............................ 6, 17, 18, 20, 23, 24, 25
Entry exit zones .......................................................18
Exit alarms ...........................................................7, 24
Exit delay..................................................................24
Exit time restart-exit delay restart/reset .................7
– 77 –
Q
Quick arm .....................................8, 17, 18, 19, 20, 21
Quick exit ................................................................. 23
T
Tablets...................................................................... 56
Talk mode ................................................................ 60
Test mode ........................................................... 65, 66
Time and date .................................................... 14, 41
Touchscreen control ............................................ 5, 10
Traffic ....................................................................... 13
Two way voice feature (alarm audio verification) .. 6,
60
Two-way voice ............................................................ 5
R
Ready indicator ................................16, 17, 18, 20, 26
Real-time clock ........................................................... 5
Reboot ................................................................. 65, 66
Rechargeable, nickel-metal hydride battery pack . 68
Reminder feature ..................................................... 51
Reminders ................................................................ 51
Remote access feature ............................................. 61
Remote services........................................................ 61
Reset video cameras ................................................ 58
Restart exit delay ....................................................... 8
Restarting exit delay ............................................... 24
Return/home............................................................. 59
Rules ................................................................... 44, 47
U
Unrestricted menu .................................................. 14
User access ............................................................... 33
User codes ............................................................ 5, 33
V
Video......................................................................... 13
Video camera control ......................................... 57, 59
Video camera reset .................................................. 58
Video cameras .......................................................... 57
Video function buttons. ........................................... 57
View/control a single camera .................................. 59
Voice dialog ................................................................ 6
Volume level ................................................ 10, 16, 40
VOX (voice) mode .................................................... 60
S
Scan access points .............................................. 54, 56
Schedules .................................................. 5, 44, 45, 46
Schedules feature................................................. 5, 44
Security .............................................................. 13, 26
Security codes ........................................................ 5, 6
Security screen .......................................23, 28, 29, 31
Servicing information .............................................. 75
Silence alarm ........................................................... 26
Silencing a fire/carbon monoxide alarm ................. 69
Silencing low battery warning tones ...................... 67
Silent emergency/silent alarm ................................ 30
Silent exit ................................................................. 21
Slide show ................................................................ 62
Smoke detectors ...........................6, 66, 67, 69, 70, 73
SMS feature ............................................................. 61
Speaker phone.......................................................... 10
Status area ............................................................... 13
Stay mode ....................................................... 6, 17, 23
System battery ......................................................... 68
System settings ........................................................ 40
System status ........................................................... 16
W
Walk test ............................................................ 65, 66
Weather .................................................................... 13
WiFi configuration .................................................. 54
WiFi internet connection ........................................ 57
Wireless keypads ....................................................... 5
Wireless sensors ...................................................... 67
Z
Zones .............................................. 5, 6, 16, 28, 29, 63
Zones .......................................................................... 5
Zones ........................................................................ 66
Z-wave devices ......................................................... 44
– 78 –
TWO YEAR LIMITED WARRANTY
Honeywell International Inc., acting through its Security & Communications business (“Seller”), 2 Corporate Center Drive,
Melville, New York 11747 warrants its products to be free from defects in materials and workmanship under normal use
and service, normal wear and tear excepted, for 24 months from the manufacture date code; provided, however, that in the
event the Buyer presents a proper invoice relating to the purchased product and such invoice bears a date later than the
manufacture date, then Seller may at its discretion, reflect the warranty period as commencing at invoice date. Except as
required by law, this Limited Warranty is only made to Buyer and may not be transferred to any third party. During the
applicable warranty period, Seller will repair or replace, at its sole option and as the exclusive remedy hereunder, free of
charge, any defective products.
Seller shall have no obligation under this Limited Warranty or otherwise if the product:
(i) is improperly installed, applied or maintained;
(ii) installed outside of stated operating parameters, altered or improperly serviced or repaired by anyone other than the
Seller/Seller’s Authorized Service/Repair Center;
(iii) damage is caused by outside natural occurrences, such as lightning, power surges, fire, floods, acts of nature, or the like;
or
(iv) defects result from unauthorized modification, misuse, vandalism, alterations of serial numbers, other causes unrelated
to defective materials or workmanship, or failures related to batteries of any type used in connection with the products
sold hereunder.
Exceptions to Warranty With Respect to Honeywell Products listed below:
Hardwire Contacts and PIRs – Seller warrants parts for hardwire contacts and PIRs in accordance with the terms of the
above limited warranty for a period of five (5) years from the manufacture date code.
EXCLUSION OF WARRANTIES, LIMITATION OF LIABILITY
THERE ARE NO WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS
FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. TO THE FULLEST EXTENT PERMITTED BY LAW, IN NO CASE SHALL SELLER BE LIABLE TO ANYONE
FOR ANY (i) CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES ARISING OUT OF OR
RELATING IN ANY WAY TO THE PRODUCT AND/OR FOR BREACH OF THIS OR ANY OTHER WARRANTY OR
CONDITION, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE
LOSS OR DAMAGE IS CAUSED BY SELLER’S OWN NEGLIGENCE OR FAULT AND EVEN IF SELLER HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH LOSSES OR DAMAGES. Any product description (whether in writing or
made orally by Seller or Seller’s agents), specifications, samples, models, bulletin, drawings, diagrams, engineering sheets or
similar materials used in connection with the Buyer’s order are for the sole purpose of identifying the Seller’s products and
shall not be construed as an express warranty or condition. Any suggestions by Seller or Seller’s agents regarding use,
applications, or suitability of the products shall not be construed as an express warranty or condition unless confirmed to be
such in writing by Seller. Seller does not represent that the products it sells may not be compromised or circumvented; that
the products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise, or that the products
will in all cases provide adequate warning or protection. Buyer understands that a properly installed and maintained alarm
may only reduce the risk of a burglary, robbery or fire without warning, but it is not insurance or a guarantee that such will
not occur or will not cause or lead to personal injury or property loss. CONSEQUENTLY, SELLER SHALL HAVE NO
LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON ANY CLAIM AT ALL
INCLUDING A CLAIM THE PRODUCT FAILED TO GIVE WARNING. However, if Seller is held liable whether directly or
indirectly for any loss or damage with respect to the products it sells, regardless of cause or origin, its maximum liability
shall not in any case exceed the purchase price of the product, which shall be fixed as liquidated damages and not as a
penalty, and shall be the complete and exclusive remedy against the Seller. Should your product become defective during
the warranty, please contact your installer to facilitate repair or replacement with Seller pursuant to the terms hereof.
Seller reserves the right to replace any defective product under warranty with new, refurbished, or remanufactured product.
– 79 –
2013
Ê800-16084BŠ
800-16084 12/13 Rev. A
- Uploaded