LKP500 Install Guide

Installation and Setup Guide
Ref: LKP500-EN / LKP500-ENC

FEATURES & NOTES
• Wireless alpha keypad serves as a secondary keypad for controlling the Lyric
Smart Controller’s security functions.
• Uses SiX™ technology protocol for secure, bidirectional communication.
• Use up to eight (8) keypads with the Lyric Smart Controller.
• Easy enrollment in the Controller.
• Mounts to a wall or desk stand.
• Supervised
• Locate the keypad within 300 feet of the Lyric Smart Controller.
• Powered by an external 110VAC input/9VDC output power pack (supplied).
• Battery pack (7.2VDC) provides 24-hour backup power (supplied).

Keypad Supervision•
• Keypad supervision signals are sent every 60 seconds
(cannot be changed). Supervision fault occurs if the
controller fails to receive a keypad supervision signal
within 200 seconds.
• When a trouble condition is detected, the keypad
displays a trouble message and begins to beep.
• Press any key to stop the beeping.

INSTALL THE BATTERY AND CONNECT THE POWER SUPPLY WIRES TO THE KEYPAD
IMPORTANT:

DO NOT connect the power
supply to an AC outlet until ready
to enroll the keypad in the
Controller. See “Enroll the
Keypad” section.

MOUNT THE KEYPAD (Wall Mounting Shown)
NOTE: The keypad should not be
mounted within line of sight of
motion sensors.
Desk Stand Mounting Option
If desired, the
optional desk stand
kit can be used. See
instructions
included with kit
LKP500-DK.

ENROLL THE KEYPAD
The keypad must be enrolled in the Lyric Smart Controller before it can be used.

1.

At the Smart Controller, enter Programming
mode and follow the control’s instructions to
enter keypad enrollment mode
Security > Tools > Installer Code > Program > [V] > RF
Keypad > Add New (or select desired zone number and
press Edit) > Serial Number.

4.

• RF keypads are assigned zone numbers,
starting with zone 850. Selecting “Add New”
automatically assigns the next available RF
keypad zone number.

2. While the Controller is in enrollment mode, plug
the keypad’s power pack into a 24hr, nonswitchable 110VAC, 60Hz outlet.

• The keypad automatically attempts to pair with the
Controller.
• If enrollment is not successful, press any of the keys
on the keypad to restart the pairing process or
disconnect and reconnect power.

3. After successful pairing,

keypad beeps and display
goes blank until exit of
program mode. System then
displays Disarmed, Ready.
• When enrolled, the keypad’s
ID number appears on the
Controller’s screen.

After enrollment, program and save the keypad’s zone options (zone descriptor, etc.) at the Smart Controller.
NOTES: • Make sure to assign a descriptor be assigned to the keypad for easy identification when keypad events occur.
• After enrollment, update the Keypad firmware (via the Controller or AlarmNet 360) to ensure the latest version is used. See
Controller’s instructions.
IMPORTANT: Once enrolled, the keypad cannot be used with another control panel until it is un-enrolled (deleted)
from the current controller. See the Smart Controller’s Programming Guide for details on removing devices.

BATTERY REPLACEMENT
IMPORTANT: Unplug the keypad power supply BEFORE starting.
Reconnect power after the keypad is re-mounted.

SPECIFICATIONS
Physical:
Frequency:
Battery
Pack:
Transformer:

3.75” W x 4.625” H x 1.125” D (95mm x 118mm x 29mm)
2.4 GHz
LKP500-24B: Battery part number 300-06868-GP:
7.2V, 6xAAA, 6x600mAH, NiMH
Part number 300-07332US: 110VAC, 60Hz
input/9VDC, output 1A, 2-prong
Canada use: 300-07332CAN
LCD Display: 2x16
Sounder:
Speaker/Codec
Approvals
UL985/UL1023; ULC-S545 & ULC/ORD-C1023

USING THE KEYPAD
The Lyric Smart Keypad can control the security functions of the Lyric Smart Controller. The keypad also has two menus for setting various
options (see Keypad Settings Menu below). Refer to the Lyric Smart Controller’s User Guide for more information about Security functions.

Keypad System Functions
FUNCTION

PRESS

NOTES

Arm Away

Away then enter user code.

Exit delay begins. System arms in Away mode.
(see User Guide for Auto-Stay option, if enabled)

Arm Stay

Stay then enter user code.

Exit delay begins. System arms in Stay mode.

Quick Arm
(if programmed)

Hold Security Shield for 3
seconds, then select Away or
Stay arming mode.

Quick Arm allows arming the system without
entering a user code.

Bypass Zones

With system not ready:

(if zones are
faulted)

Away or Stay then enter user
code.

System automatically bypasses all faulted zones
and arms in the selected mode.

Press Select when prompted.
Panic

Exit delay begins. System arms in selected mode.

NOTE: Force Bypass must be enabled at the
controller for this feature to operate.

Hold Panic key for 3 seconds,
then select:
• Fire
• Police (default = silent)
• Medical

The 3 Panic keys light red until one is selected,
then:
• An alarm signal is sent to the central station
• Alarm sounding starts (if programmed to do so)
• If the selected Panic function is programmed to
be silent, the keypad returns to normal state.

Disarm

Security Shield, then enter user
code.

System disarms.

Shield & Panic Indicators

Cancel Silent
Panic Alarm

Security Shield, then enter user
code.

Panic alarm is canceled.

The Security shield is a single key; the
and
icons are
not separate buttons. Security status is indicated by color:

(if programmed)

Display
Status
security status

Cancel

Displays the system’s current security status.
(Armed/Disarmed, Away/Stay/Custom arming
mode, exit countdown, Ready/Not Ready, Fault,
Trouble and Bypass conditions.)

Cancel

Indicator

Color

State

Meaning

Security
Shield

unlit

unlit

• System disarmed, not ready to arm,
(press Status key to show faults)
• Zone fault or zone trouble
• AC loss or low battery

Green

lit steady

• System ready to arm

blinking

• System ready with AC Loss

lit steady

• System armed
• Exit delay in progress, system
arming
• AC Loss or low battery

Cancels the entry and returns to Status display.

Keypad Settings Menu

Red

There are two Settings menus: User Settings and Advanced Menu. Use the Select,
Scroll and Cancel keys to navigate the menus.
Key
Select [ 1 ]
Scroll [ 0 ]
Cancel (Away)

To
1.
2.
3.
4.
5.
--

Function

Status

White

blinking

Press and hold to start the Settings menu.
Also used to select menu options.
Press to scroll through the available menus and the settings
in menus.

Panic

unlit

unlit

Red

lit steady

• Not active.
• AC loss or low battery
• Active, waiting for selection of
panic alarm type.

Cancels the current entry and returns to Status display.

Access User Settings
Press and hold the Select [ 1 ] key until the menu begins.
Use the Scroll [0] key to scroll the settings.
Use the Select key to choose the desired menu item.
Use the Scroll key to toggle the menu options.
Press the Select key to save your settings.
Press Cancel at any time to exit the menu.

User Settings Menu (brackets [ ] indicate default values; greater than
symbol “>” on keypad display indicates keypad’s current setting)
Options

Setting

Chime

[On]/Off

Notes
On: keypad beeps when a zone is faulted if
Chime mode is turned on at the control
Off: keypad does not beep upon faulted zones

Exit Tone
(beeps)

[On]/Off

On: keypad beeps during exit delay period
Off: keypad does not beep during exit delay

Entry Tone
(beeps)

[On]/Off

On: keypad beeps during entry delay period
Off: keypad does not beep during entry delay

Voice
Volume

[Med]/High/Off

Adjusts the desired volume for keypad
announcements.
Off: mutes arm/disarm announcements;
alarms are always announced

Key Level

[Med]/High/Low

Adjusts the brightness of key lighting.

Display Level [Med]/High/Low
[Always On]
Backlight
(for display)

blinking

Auto Off
On Alarm Only

To Access the Advanced Menu
1. Press and hold the [3] key until “Advanced Menu Use Scroll Key” is
displayed.
2. Use the Scroll [0] key to scroll the menus.
3. Use the Select key to choose the desired menu item.
4. Use the Scroll key to view the information.
-- Press Cancel at any time to exit the menu.
Advanced Menu
Setting

Firmware Upgrades
Software upgrades may be available for this product. Upgrades can be
installed manually using the Lyric Smart Controller or can be done via
AlarmNet 360™.
To upgrade the keypad firmware using the Lyric Smart Controller, go
to the following Controller menu and follow the prompts:
Security > Tools > Master Code > Advanced > Upgrade Sensor Firmware

After performing the upgrade command, the keypad displays the
upgrade status then, when done, automatically resets twice. After the
keypad completes the reset, it returns to normal operation.
RF Exposure

Warning – The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8
inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna
or transmitter except in accordance with FCC multi-transmitter product procedures.

Mise en Garde

Exposition aux Frequences Radio: L'antenne (s) utilisée pour cet émetteur doit être installée à une distance
de séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.

Notes

Firmware
Use Scroll to
choose firmware
components

Displays the various keypad
component firmware versions.
See Firmware Upgrades section for
details on upgrading the firmware.
MAC: displays the keypad’s MAC ID.

Default Keypad

Cancel/Delete

Delete: if used within 24 hours of
initial enrollment, allows keypad
reenrollment in a specific controller
in case enrollment in that controller
failed (i.e., the keypad inadvertently
enrolled in a different controller).
“Delete” resets the keypad to
factory default settings and
removes the communication link
data in the controller in which it is
enrolled, allowing the keypad to be
reenrolled in the desired controller.
Cancel: exits from Default Keypad
screen without making a change.
Use to manually reset the keypad.

NOTE: After 24 hours,
the “Delete” function
is disabled. If selected
after 24 hours, “Must
use panel to delete” is
displayed. If keypad
removal is needed, the
keypad must be
deleted from the
associated controller
using the controller’s
programming options.

Adjusts the brightness of the display.
Always On: display remains always on
Auto-Off:
display turns off after a period of
inactivity.
On Alarm
display turns on when an
Only:
alarm occurs and remains lit until
the keypad is disarmed.

Options
App (version level)
Touch (touch screen)
Boot (boot loader)
RF6 (comm. protocol)
MAC (MAC ID)

Reset Keypad

Cancel/Select

FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation
Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the
equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the
following statement for your information: This equipment generates and uses radio frequency energy and if not
installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference
to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing
device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different
branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son
fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2)
Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.

SUPPORT & WARRANTY

For the latest documentation and online support information,
please go to: https://mywebtech.honeywell.com/
For the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa.
For patent information, see www.honeywell.com/patents

Ê800-19484V1vŠ
800-19484V1 11/15 Rev. C

MyWebTech

Warranty

Patents

2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright  2015 Honeywell International Inc.
www.honeywell.com/security