OHD Anywhere - Quick Install Guide

Wall Button Wire
Photocell wire
Power Pack
OHD Anywhere™
Control Wire
Quick Set-up Guide
DCM
(Door Control Module)
DPS
(Door Position Sensor)
Hardware Bag
Power Pack
Wire Spool
Insulated
Staple x30
WARNING
TO REDUCE THE RISK OF SEVERE INJURY
OR DEATH, READ AND FOLLOW ALL
INSTRUCTIONS.
1.
NEVER let children operate or play with the
door controls.
2.
Keep remote away from children.
3.
Locate the wall control button & DCM: A)
Within sight of door. B) At a minimum height
of 5 feet, so small children cannot reach it.
4.
Install the entrapment WARNING label next
to the wall button or console, in a prominent
location.
5.
NO ONE SHOULD CROSS THE PATH OF THE
MOVING DOOR.
6.
NEVER GO UNDER A STOPPED, PARTIALLY
OPEN DOOR.
7.
The OHD Anywhere™ operating system is
designed for unattended operation. The door
could move unexpectedly.
8.
DO NOT install OHD Anywhere™ on garage
door openers manufactured prior to 1993
without photocell non-contact safety sensors.
9.
DO NOT install on one-piece doors
10.
Install DCM in a location where it can be seen
and heard while standing in the door opening
with the door in the open position.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS
AVERTISSEMENT
POUR RÉDUIRE LE RISQUE DE BLESSURES
GRAVES VOIRE MORTELLES, LIRE ET
COMPRENDRE TOUTES LES INSTRUCTIONS.
1.
NE JAMAIS laisser les enfants utiliser ou jouer avec les
commandes de l’ouvre-porte.
2.
Tenir les télécommandes hors de la portée des
enfants.
3.
Localiser le bouton de la console murale (DCM) : A)
En vue de la porte. B) À une hauteur minimale de
1,5 m afin que les jeunes enfants ne puissent pas
l’atteindre.
4.
Placer l’étiquette d’AVERTISSEMENT en cas de
coinçage à proximité du bouton mural ou de la
console murale de manière à ce qu’elle soit bien en
évidence.
5.
NE JAMAIS PASSER SOUS LA PORTE EN MOUVEMENT.
6.
NE JAMAIS PASSER SOUS UNE PORTE À L’ARRÊT
PARTIELLEMENT OUVERTE.
7.
Le système d’exploitation OHD Anywhere™ a été
conçu pour fonctionner sans surveillance. La porte
peut se déplacer de façon inattendue.
8.
NE PAS installer OHD Anywhere™ sur les ouvre-portes
de garage fabriqués avant 1993, sans capteurs de
sécurité photoélectrique sans contact.
9.
NE PAS installer sur les portes d’une seule pièce.
10.
Installez DCM dans un endroit où il peut être vu et
entendu tout en se tenant dans l’ouverture de la porte
avec la porte en position ouverte.
CONSERVER CES INSTRUCTIONS
CONSIGNES DE SÉCURITÉ
IMPORTANTES
Included Components
Recommended Tools
Drill & 3/32 Bit
Small Common
Screwdriver
Phillips Head
Screwdriver
Wire Cutters/
Strippers
Hammer
5/16 Wrench or
Nut Driver
STEP 1
In the Home close to Wi-Fi Router:
1.
Remove mounting bracket from back of DCM. FIG.A.
2.
Plug OHD Anywhere™ into wall outlet with Power Pack.
FIG. B.
3.
Plug Power Pack into DCM controller.
WARNING
UNPLUG GARAGE DOOR OPENER PRIOR TO INSTALLING
OHD Anywhere™
Door may operate unexpectedly.
AVERTISSEMENT
DÉBRANCHER L’OUVRE-PORTE DE GARAGE AVANT
D’INSTALLER OHD Anywhere™
La porte peut fonctionner de façon inattendue.
STEP 3
In the Garage:
These factors must be determined prior to mounting OHD Anywhere™
(DCM) to the wall or ceiling.
1. Optimal Wi-Fi signal strength.
If an optimal signal cannot be located within the garage, move the
wireless router closer to the garage or install a Wi-Fi range extender
(available from most electronic stores)
2. Desired DCM location.
3. Access to 110VAC outlet within 5 feet.
1.
Plug Power Pack into wall outlet and DCM near the chosen mounting
location.
The WI-FI signal indicator LED should illuminate
signaling that the Wi-Fi signal is still in tact.
•
A
GREEN
LED indicates a good Wi-Fi signal.
•
A
RED
LED, indicates a lost or faulty signal.
Move OHD Anywhere™ to a position that
better suits the Wi-Fi signal from the router.
Contact Customer Service for further
assistance. (1-888-901-2750)
2.
Once an
optimal
signal and location is
obtained,
UNPLUG Power Pack
from the
DCM and continue to
STEP 4
.
Wi-Fi Signal Indicator
GOOD -- POOR
DPS Signal
Red/Blue LEDs
For a video of this installation,
Visit www.OverheadDoor.com/OHDAnywhere/InstallationVideo
NOTE:
Customers using control apps from other vendors and NOT
using the OHD Anywhere™ app to control this system will need to
visit www.OverheadDoor.com/OHDAnywhere for specific Wi-Fi
instructions.
FIG.A
FIG.B
DCM
Installation Prompt
39405503197 05/16
Apple and the Apple logo are trademarks
of Apple Inc., registered in the U.S. and
other countries. App Store is a service mark
of Apple Inc.
Need help or have questions? Contact OHD Anywhere™ Customer Service at 1-888-901-2750
Typical Installation shown.
Installations may vary
Scan for
iOS app
Scan for
Android app
STEP 2
In the Home close to Wi-Fi Router:
Download the OHD Anywhere™ app.
1.
Scan the QR code below or visit your devices app
store to start the setup of the OHD Anywhere™ device.
Search your app store for OHD Anywhere
2.
Follow the on-screen menus to create an account and
program system prior to wiring in the garage.
3.
At the installation prompt, disconnect
Power Pack and move system to the garage.
Scan for the
OHD Anywhere™
installation video
Scan here for additional
OHD Anywhere™
information STEP 4
Wire OHD Anywhere™: (Single door install shown)
OHD Anywhere™ will wire directly to the wall control connections at the powerhead or
directly to the wall control. New Overhead Door models shown.
Visit www.OverheadDoor.com/OHDAnywhere for more information on older models
and other brands of garage door openers.
1.
Make sure garage door opener is unplugged.
•
Leave wire spool intact for this part of the install.
2.
Split provided dual strand wire approximately 2 in. then strip 1/2 in. of insulation.
FIG. A.
3.
Press orange tabs down and insert both wires into connection points for DOOR 1
on the back of the DCM. FIG. B.
4.
Trim and split the other end of the dual strand
wire approximately 2 in. and then strip 1/2 in. of
insulation. FIG. A.
5.
Insert wire into wall control inputs either:
•
(
OPTION A
) Directly to the garage door opener.
•
OR
•
(
OPTION B
) To the Back of the wall control.
Wall Mount
Anchors (as needed)
Perforated Angle
Mount
1/2"
2"
Press tab down
to install wire.
STEP 5
Mount and Power OHD Anywhere™:
1.
Using the DCM mounting bracket as a template at the optimal
Wi-Fi location. Mark and drill 2-3/32” pilot holes and mount
bracket to wall using supplied screws. If mounting to drywall,
use anchors provided in kit or if mounting to perforated angle
at opener location, use nuts, washers and screws provided.
2.
Plug Power Pack into wall outlet. An extended screw is provided
to secure Power Pack to outlet if needed.
3.
Plug Power Pack into back of DCM as shown in
STEP 1
.
NOTE:
LEDs on DCM will flash momentarily as it reacquires signals.
4.
Snap DCM onto mounting bracket.
5.
Route wires and secure with supplied staples.
6.
Affix the warning placard next to wall control or DCM in plain
sight to signify that the door will operate remotely.
Features:
If the garage door opener is
operated by any means, the
OHD Anywhere™ app will
send an alert to your device
indicating the status of the
garage door.
A log is also created to indicate
when the door was operated.
Visit www.OverheadDoor.
com/OHDAnywhere for more
information.
*Wiring methods for other garage door openers.
All Overhead Door brand and most competitor brands of garage door openers will operate with OHD Anywhere™. Visit www.
OverheadDoor.com/OHDAnywhere to check compatibility with other manufacturer’s controls or check your garage door opener’s owners
manual for wall control wiring instructions.

OHD Anywhere™ will operate up to 3 garage door openers.
END STILE
Garage Door
Garage Door
Mounting DPS
Door
1
Door
2
Door
3
OVERHEAD DOOR CORPORATION
1-866-901-2750 or www.Overheaddoor.com
FIG.A
Button & Connection Detail
FIG. B
Split 2” & Strip 1/2”
For technical assistance, contact
your local Overhead Door
Distributor or call OHD Anywhere™
Customer Service at
1-888-901-2750
or watch the installation video at:
www.OverheadDoor.com
112612.0001
WARNING
AVERTISSEMENT
MOVING DOOR can cause serious
injury or death.
MOUVEMENT PORTE peut causer des
blessures graves ou la mort.
STAND CLEAR!
Door could close automatically.
Do Not stop or stand in doorway
SE TENIR À L'ÉCART DE LA PORTE!
La porte pourrait se refermer automatiquement.
Ne pas arrêter ou debout dans la porte.
OPTION A
Wire DCM Directly to
Garage Door Opener
Current model Overhead Door brand opener shown. *See note for other models and brands.
NOTE:
Wires from wall control to garage door opener
ARE
polarity sensitive. Be sure to reattach to the proper
terminal should they become detached.
Wall control should light when wired correctly.
Press in on orange tabs to insert wire into terminals
3 & 4 along with existing wall control wires.
OPTION B
Back of Wall Control
Connect wire along with
existing wall control wires.
OR
OR
Existing Wall Control Wire.
Use of this product, the software embedded within this product and the related application software is subject to the Terms and Conditions available at: www.OverheadDoor.com/OHDAnywhere
1
2-4
6
STEP 7
Complete the Programming:
1.
Restore power to the garage door opener.
2.
Follow the on screen prompts to complete the set-up and test the OHD Anywhere™ system.
NOTE:

This kit includes one DPS for use with one door only. The DPS included is already programmed to the DCM . Additional sensors can be purchased separately
from your local Overhead Door retailer. To program additional sensors, first complete STEP 7 initial setups and programming, then go to “Add a Door Sensor” under
the “Doors” tab inside the app or view the installation video at www.OverheadDoor.com/OHDAnywhere/InstallationVideo.
NOTE:

A white light will flash and an audible beep will sound as an indication that the door is about to move when commanded by the Aladdin Connect™ or other
compatible app(s).
STEP 6
Mount DPS Module to Garage Door:
DO NOT remove the battery “
PULL TAB
” from DPS until
directed by the app.
The DPS should be mounted on the
TOP door panel
only.
Mount to steel reinforced end stile on the far left or right
under the top hinge. DO NOT mount to unreinforced door
panel.
1.
Clean door where DPS will mount.
2.
Install double sided tape to back of mounting bracket and affix to
door.
NOTE:

Double sided tape is designed to hold bracket in place temporarily
only. Not to be used for permanent mounting.
3.
Pre-drill 2 - 3/32 holes. DO NOT drill all the way through door.
4.
Use included self tapping screws to mount DPS bracket to top door
panel end stile.
5.
Slide DPS down onto mounting bracket. DPS should snap onto
bracket.
NOTE:
The DPS included with this kit is already programmed to the DCM. See
the NOTE under
STEP 7
regarding additional sensors (DPS).