Resideo Lyric User Guide - 11/15 Rev. F
Related Products
Related Categories
- Small Business Security Systems
- Monitored Home Security Systems
- Home Security Systems
- DIY Wireless Security Systems
- Business Security Systems
- Apartment Security Systems
Document Transcript
1
User
Reference
Guide
Ref: LCP500
- L/LCP500
- LC
800-
18078
11/15
Rev.
F
2
IMPORTANT!
PROPER INTRUSION PROTECTION
For proper intrusion coverage, sensors should be located at every possible point of entry to a home or
commercial premises. This would include any skylights that may be present, and the upper windows in a
multi-
level building.
In addition, we recommend that radio backup be use
d in a security system so that alarm signals can still be
sent to the Central Monitoring Station in the event that the internet connection is interrupted or not working
correctly (alarm signals are normally sent over the Wi
-Fi® and Internet network)
.
EARLY WARNING FIRE DETECTION
Early warning fire detection is important in a home. Smoke and heat detectors have played a key role in
reducing fire deaths in the United States. With regard to the number and placement of smoke/heat detectors,
we subscribe to
the recommendations contained in the National Fire Protection Association's National Fire
Alarm Code (NFPA 72). These recommendations can be found on
page
71
of this manual.
System Compatibility Notice
Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell for
use with
your security system. Your Honeywell security system is not designed for use with any device that
may be attached to your security system's control or other communicating bus if Honeywell has not approved
such device for use with your security system. U
se of any such unauthorized device may cause damage or
compromise the performance of your security system and affect the validity of your Honeywell limited warranty.
When you purchase devices that have been manufactured or approved by Honeywell, you acqui
re the
assurance that these devices have been thoroughly tested to ensure optimum performance when used with
your Honeywell security system.
Lyric™ Lock
Your system supports advanced features designed to keep it functioning optimally. These capabilitie
s
include: the ability to interact with Honeywell and your dealer’s network for the setup and programming of its
features, support for remote software updates and the ability (when enabled by your monitoring dealer) to
enhance your security by preventing a
n unauthorized takeover of the system by another monitoring
company. In the event that your dealer has enabled the feature to prevent an unauthorized takeover and you
wish to authorize a new company to take over your system, you may request that Honeywell
remotely disable
this feature. Honeywell will require documentation that you have attempted to contact your existing security
dealer and that they have failed to respond, or failed to agree to your request.
3
TABLE OF CONTENTS
OVERVIEW
........................................................................................................................................................................................
5
About This Guide
........................................................................................................................................................................
5
Basic Functions
...........................................................................................................................................................................
6
About the Control Panel
..........................................................................................................................................................
7
Home Button Status Indications
...........................................................................................................................................
7
Th
e Tools Menu
...........................................................................................................................................................................
8
SECURITY
..........................................................................................................................................................................................
11
Security Features
.......................................................................................................................................................................
11
False Alarm Pr
evention
...........................................................................................................................................................
12
Arming the System
...................................................................................................................................................................
13
Disarming the System
.............................................................................................................................................................
15
Bypassing Protection Zones
.................................................................................................................................................
15
Entry and Exit Delays
..............................................................................................................................................................
16
Panic Alarms
...............................................................................................................................................................................
17
Chimes/Voice Annunciations
...............................................................................................................................................
18
Audio Alarm Verification
(Two
-Way Voice)
...................................................................................................................
19
Built
-In Camera
..........................................................................................................................................................................
19
AUTOMATION: AN INTRO
DUCTION
......................................................................................................................................
21
AUTOMATION: SMART SC
ENES
.............................................................................................................................................
23
Smart Scenes and User Access
...........................................................................................................................................
23
Creating a Smart Scene
.........................................................................................................................................................24
Hold/Run/Show
........................................................................................................................................................................
27
AUTOMATION: VOICE COMMAND
........................................................................................................................................
29
Setup
.............................................................................................................................................................................................
29
Voice Command Assignment
.............................................................................................................................................
30
Using Voice Command
..........................................................................................................................................................
30
Counter (Sensitivity Settings)
..............................................................................................................................................
31
AU
TOMATION: Z
-WAVE DEVICES
........................................................................................................................................
33
Operating Z
-Wave Devices Manually
..............................................................................................................................
34
Adding Z
-Wave Devices (Include)
...................................................................................................................................
34
Deleting Z
-Wave Devices (Exclude)
.................................................................................................................................
35
Editing Z
-Wave Device Names
...........................................................................................................................................
35
Advanced Tools
........................................................................................................................................................................
35
Failed Devices (Fa
iled Nodes)
............................................................................................................................................
36
Garage Doors
.............................................................................................................................................................................
37
Important Notes About Z
-Wave Devices
.......................................................................................................................
38
Notes on Thermostats
............................................................................................................................................................
39
Z- Wave Compatibility
...........................................................................................................................................................
40
VIDEO
................................................................................................................................................................................................
41
Viewing and Naming Cameras
............................................................................................................................................
41
Adding a Camera
.....................................................................................................................................................................
41
Video Recovery
.........................................................................................................................................................................42
USERS AND SECURITY CODES
.............................................................................................................................................
43
User Codes
.................................................................................................................................................................................
43
Duress Code
..............................................................................................................................................................................
43
Adding Users and Ass
igning Codes
.................................................................................................................................
44
Changing Security Codes or the Duress Code
.............................................................................................................
44
Deleting a User
.........................................................................................................................................................................
44
User Settings
.............................................................................................................................................................................
45
SYSTEM SETTINGS
......................................................................................................................................................................47
Brightness/Volume/Cleaning
..............................................................................................................................................47
Wi
-Fi Configuration
.................................................................................................................................................................
47
Software Updates
...................................................................................................................................................................
48
Slide Show
.................................................................................................................................................................................
49
4
Date / Time
................................................................................................................................................................................
49
Events
..........................................................................................................................................................................................
50
Keypad
........................................................................................................................................................................................
50
TESTING YOUR SYSTEM
............................................................................................................................................................
51
Testing Sensors (Walk Test)
.................................................................................................................................................
51
Testing Communications
.......................................................................................................................................................
52
Reboot
..........................................................................................................................................................................................
52
MAINTENANCE
.............................................................................................................................................................................
53
Care and Cleaning
....................................................................................................................................................................
53
Battery Replac
ement
..............................................................................................................................................................
53
Communication Module Replacement
.............................................................................................................................
55
SYSTEM DISPLAY AND B
UTTONS
........................................................................................................................................
57
WIRELESS KEYS
...........................................................................................................................................................................
59
Key Assignments
......................................................................................................................................................................
59
SiXFOB Wireless Key Status Indications
.........................................................................................................................
59
EVENT LOG CODES
.....................................................................................................................................................................
61
APPENDIX: VIDEO DOORBELL
...............................................................................................................................................
65
Change the Video Doorbell Descriptions and Chime Sound, or Delete a Video Doorbell
...........................
65
Install a Video Doorbell
..........................................................................................................................................................
65
GLOSSARY
......................................................................................................................................................................................
67
FIRE/CO ALARM SYSTEM
.......................................................................................................................................................
69
In Case of Fire
...........................................................................................................................................................................
69
In Case of Carbon Monoxide Alarm
.................................................................................................................................
69
Silencing a Fire/Carbon Monoxide Alarm
......................................................................................................................
69
NATIONAL FIRE PROTEC
TION ASSOCIATION SM
OKE DETECTOR RECOMME
NDATIONS
.........................
71
Emergency Evacuation
..........................................................................................................................................................
72
REGULATORY AGENCY STATEMENTS
...............................................................................................................................
73
OWNER'S INSURANCE PR
EMIUM CREDIT REQUEST
...................................................................................................
75
YOUR SYSTEM INFORMAT
ION
...............................................................................................................................................
77
LIMITATI
ONS OF THIS ALARM SYSTEM
.............................................................................................................................
82
TWO YEAR LIMITED WAR
RANTY
.........................................................................................................................................
83
5
Overview
The
Lyric
™ Controller
combines
a security system and
home automation
with
an easy to use
interface.
All
functions
can be
operated
from the Controller and many Lyric features can be
accessed
from
internet
-connected smart
devices.
Security
functions can be operated from optional wireless keys
and wireless
keypads.
Wireless
and
wired
sensors provide burglary protection
and smoke and
combustion
detectors
provide early fire
and
carbon monoxide (CO)
warning
s.
Lyric
monitors
sensors
and system status
to
initiate alarms and generate
alerts
. The
system
can
also
send alarm and
status messages
to
a central
monitoring
station
via the cellular phone
network or the
Internet
. Lyric can also provide two
-way voice communication with the central station.
Arming options
Use
Away
mode when no one will be home. Exterior doors and windows are
protected; interior areas can be monitored by motion detectors.
Use
Stay
mode to protect exterior doors and windows when the house will
be occupied.
Arming modes can be customized to exclude specific parts of the premises.
Selected door/window and movement sensors can be excluded temporarily.
Fire protection cannot be bypassed or suspended.
Panic buttons
Activate police and fire alarms or emergency alerts from the Controller
,
wireless keys
or remote keypad. Panic modes can be customized by your
installer.
Audio Alarm Verification
(
Two
-way Voice
)
Talk directly to your central monitoring station from the Co
ntroller.
Video
Monitor and control compatible Wi
-Fi® cameras. View video from as many as
four cameras simultaneously.
User and Security Codes
4-digit codes allow Lyric to distinguish between users with different types
of
access
to system functions
.
The
Master User
is typically a household member who can perform all
normal system functions. Guest and other users each have unique codes.
Voice Command
s
Use spoken trigger phrases to control
Smart Scenes
and video cameras.
Automation
Automate lights, locks and other compatible devices.
Some features can be
operated remotely via remote services such as Honeywell Total Connect
®.
Smart Scene
s
Easy
-to-program combinations
of security and
automation features.
Message center
Record
and play back voice messages.
Weather
Displayed on the touch screen
.
Remote Keypad
Operate security functions
from the Lyric Keypad.
(Optional
)
Remote Services
Remote monitoring and control functions from mobile devices or web
browser.
Requires remote
services
plan.
Built
-in Camera
Lyric takes a snapshot of the person at the Controller
when the system is
disarmed.
Requires remote services
.
About
This Guide
Throughout the guide, you will see these tips for finding the menus and controls you need.
For example
,
Home >
Security
>
Tools
>
Users
Means:
On the
Home
screen,
select
Security
.
On the Security menu
, select
Tools
.
On the Tools menu, select
Users
.
The
illustrations
in this manual may differ slightly from your system.
Also, please note that the
terms “panel”, “security panel” and “Controller” are used interchangeably.
6
Basic Functions
Press the
button below the touchscreen
to return to the Home screen
from other functions
Security
Press
Security features
on the
Home screen
Arm
in Stay mode
and enter a user code
Arm
in Away mode
and enter a user
code
Disarm
system
&
silence
alarms
and enter a user code.
Repeat to silence alarms/alerts
Panic
Press
and
hold
this button
below the touchscreen.
Then
press
:
or
or
or
on the
touchscreen
Other Panic modes may appear on the screen if they are programmed in your system
Video
Press
on the Home screen to view and configure Wi
-Fi® cameras
Control Panel
Settings
Press
on the Home screen
Screen
brightness
Use the
Brightness slider
Voice announcements volume
Select
VOICE
and use the
slider
Chime volume (count
-down beeps,
other sounds)
Select
CHIME
and use the
slider
Clean
touchscreen
Touch
to disable all controls for 15 seconds
Automation Features
Press
Operate & manage Z
-Wave
® devices
on the Home screen
Create & manage Smart Scenes
on the Home screen
Use & manage Voice Commands
then
then enter Master User code, then
Using Voice Command
s
Speak trigger phrase
Lyric
™ confirms it has heard
a trigger phrase.
Confirmation is
optional. Three phrases are available and can be changed later.
Speak command
phrase
Lyric
executes the operation associated with the command,
co
nfirms operation.
Five voice commands can be associated with
Smart Scenes. The command “Cameras” launches the Video function.
Common
Master User Functions
Press
on the Home screen. On the Security menu, press
and enter Master User code.
Add, delete or modify user codes
System
tests
and s
elect
Walk Test or Comm.
Test
7
About the Control
Panel
The
display
may vary
with your connected devices and services.
•
Security s
ystem status appears
at the top of the
screen.
•
Wi
-Fi® status
appears
at
top left
.
•
Time, date and l
ocal
weathe
r appear
at left
. Touch
5 Day Forecast
for weather information.
The
Home
screen
normally shows
:
•
Security
: Arm and disarm
the system
with
various
options
.
•
Automation
: Control lights
, locks
and other devices.
•
Video
: View
and control Wi
-Fi cameras
.
•
Smart Sce
ne
s
: Customize and automate
security and comfort features.
•
Notices
: View system
updates
and other information from your security
company
.
•
Settings
: Adjust
screen
brightness
and
audible indicator
volume
, hide controls
for
screen
cleaning
.
Press
for Help videos and other features.
NOTE
If the Controller loses AC power, playback of Help videos is disabled to minimize
drain on the backup battery. If power is lost while you are watching a Help video,
playback may continue
.
Below the touchscreen:
Press
to return to the Home scree
n.
Press
for
Fire, Police and
other
emergencies
.
NOTE
If the Controller loses AC power, the Home button begins to blink slowly after 15
minutes on battery backup (red if the system is armed, green if not armed). In this
situation, the Panic button goes dark, but Panic functions remain available.
Home Button Status Indicat
ions
The Home button
shines green or red to indicate system status
:
Green, steady
System is ready to be armed
Red, steady
System is armed
Green, blinking
System is disarme
d, and not ready to be armed (
fault or alarm exists)
Red, blinking
An Alarm condition exists.
Red/Green, blinking
alternately
System is in Programming mode
or Two
-
Way Voice communication is
active
.
See the
Panic
section for information on silent alarms and the Home button.
Built
-in camera
USB port
(underside
)
Panic
Home
Status
Touch
screen
Wi
-Fi status
8
Audible Indicators
Beeping sounds
accompan
y entry/exit countdowns
, pressed buttons and other
functions.
Volume is adjustable for voice announcements
, chimes
and
most sounds.
Alarms are signaled by the
Controller’s
built
-in sounder
. Alarm
volume
is
not
adjustable.
Software Update Notifications
Software updates for the Controller are
published
periodically.
Most upda
tes request user
permission.
Select
Accept
,
Yes
or
OK
to instal
l the update.
Certain critical updates are installed
automatically
. After updates of this type, information
about the update
appears
on
-screen.
The Tools Menu
Home > Security > Tools
This menu offers access to most of Lyric’s important settings
and maintenance functions
.
NOTE
:
The
Master User code
is required to access Tools.
Features available from this screen include:
Users
Master User can add/remove other users and control users’ access
to features. See
Users and Security Codes
.
Events
View and export system event logs.
See
Events
.
Advanced
Access to software upgrades, tests and user maintenance functions.
Includes
features found in
Maintenance
and
System Settings
.
Keypad
Manage mobile devices running keypad apps. See
Keypad
.
Date/Time
Set the system’s calendar and clock. See
Date and Time
.
Reminders
Record and schedule voice memos. See
Reminders
.
Voice
Command
Use simple phrases to control Smart Scenes or operate Wi
-Fi® video
cameras. See
Voice Command
.
Wi
-Fi Config
Configure Wi
-Fi access points, set security and choose automatic or
manual video recovery. See
Wi
-
Fi Configuration
.
Press
on the right side of the screen for more
.
Slide Show
View selected photos on the Lyric
™ display. See
Slide Show
.
SkyBell Setup
(Video Doorbell)
Manage
Video Doorbell
settings (change
descriptions
, chime
sounds
, or
delete
from the system)
. See
Video Doorbell
Appendix.
Return to the Security menu.
9
Notices
Home > Notices
The
Notices
icon
alerts you to new information from your security company
. Press
for more
information.
Messages
Home > Security > Message
Audio messages for all users can be recorded on the Controller
.
NOTE
Audio Messages on the Controller are deleted when the system’s firmware is
updated.
To work with Messages:
1.
On the Security menu
, select
Message. If
there are
none are saved, the list shows
No
items to display
.
2.
Press
Add New
. Recording controls appear.
3.
Use the
Record
,
Stop
,
Play
and
Delete
buttons to record and review your message.
4.
Press
to return to the message list.
In the message list, select a message bef
ore pressing
Play
.
The
Delete All
button requires confirmation. Press
Yes
when asked
Are You Sure?
When messages are stored in the Controller
, the Message
icon
is highlighted.
Reminders
Home > Security > Tools > Reminders
Reminders can be scheduled to display a text note and optionally, play
a brief audio message.
Reminders that are set to require acknowledgment remain on-
screen and repeat their audio
until dismissed.
NOTES
•
The
Master User code is required to access Tools
.
•
Reminders can only be created when the system is disarmed.
•
Reminders that don’t require acknowledgment will appear on the screen, play any
included audio once and clear themselves automatically.
To create a Reminder:
1.
On the
Tools
menu,
select
Reminders
. If there are
none are saved, the list shows
No
items to display
.
2.
Press
Add New
and
Name
.
3.
Use the on-
screen keyboard
to assign a name
and remember to
press
S
ave
.
4.
Select
Frequency
and
then
Once, Daily, Weekly, Weekday or Monthly.
5.
If selecting
Once, set a Date and Start Time next.
•
If Daily, set a Start Time.
•
If Weekday, set a Start Time.
•
If Weekly, set a Day of the Week and a Start Time.
•
If selecting Monthly, set a Day of the Month and a Start Time.
6.
To add an audio message, press
Voice
and selec
t
Yes
. Use the Record
, Stop,
Play
and
Delete
buttons to record and review the message. When finished recording, press
.
7.
To require that the Reminder is acknowledged, press
Acknowledge
and select
Yes
.
8.
Press
Save
.
To
dismiss
a Reminder that requires acknowledgment, press
OK
.
10
11
Security
Home > Security
IMPORTANT
If the Controller is beeping rapidly when you enter the premises, an alarm
has
occurred
and an intruder may
still be
nearby
.
LEAVE IMMEDIATELY and CONTACT THE POLICE from a safe location.
Security Features
NOTE
S
•
For
Lyric
™ to report alarms over the internet, your Wi
-Fi® network
MUST
have power
at all times.
•
You must arm your security system in order for it to sound alarms
.
Sensors and
Zones
Lyric’s
sens
ors are assigned to numbered
zones
that correspond to
areas of your
home
. For example, the
sensor on an entry/exit door m
ight
be assigned to Zone 03,
a device in a bedroom to Zone 06, and so on.
When alarms o
r trouble conditions occur, the touchscreen
displays
the z
one number
and a d
escription of the sensor involved
.
Fire
Protection
Fire protection
is always active when the system is operating normally. An alarm
sounds if a fire condition is detected. See
Fire/CO Alarm System
for important
information about
fire protection, smoke detectors and planning emergen
cy exit
routes
.
Carbon
Monoxide
Carbon
monoxide (CO) detectors, if installed, are always active and sound an alarm if a
carbon monoxide
condition is detected.
See
Fire/CO Alarm System
for more
information.
Burglary
Protection
Lyric provides STAY and AWAY burglary protection
.
STAY
mode protects
windows and exterior doors
, allowing you to move around
inside your home
without setting off an alarm
.
AWAY
mode protects the entire
premises, including interior motion detectors if
present.
Both modes
offer
an entry
delay period
that allows you
to reenter the
home
without
setting off an alarm. For long periods such as vacat
ions
, the entry delay
can be
turned off while
arming the system.
Lyric also allows you to
Bypass
selected sensors before arming the system.
The system also features
C
hime
mode,
which can alert you to the opening of
protected doors and windows while the system is not armed.
Security
Codes
At the time of installation, the installer asks the homeowner to choose a personal
4-digit security code, known as the
“Master
User code
”.
Other users can be added
, typically with less control over
the system than the Master
User. See
Users and Security Codes
.
A user code is required when
arm
ing or
disar
ming
and for some other
functions
.
Alarms
Alarms are signaled by
the
Controller’s
internal sounder
(and external sirens if connected)
.
The screen indicates
the zone
where the alarm has occurred.
After 15
seconds, the
sounder stops temporarily and the system begins voi
ce announcements of relevant
zone
information.
After
the zones are announced, the pane
l’s sounder resumes sound
ing. Alarm sounds
and voice announcements alternate until the system is disarmed or until alarm bell
timeout occurs. If
the
system is connected to central monit
oring, an alarm message
is sent.
To silence
the sounder
, disarm the
system. The zone(s) causing the alarm remain
displayed
, indic
ating
Memory Of Alarm
. See
Clearing a Panic Alarm
for more
about
clearing memory of alarm.
Audio Alarm
Verification
Allows your central monitoring station to lis
ten to or talk with persons
on the
premises.
Keypad
Lockout
If 24
numeric keys (0
-9) are entered within a period of 15 minutes and no valid command is
executed, Lyric will not process any further numeric key
-presses for the following 15
minutes. Entering any numerical keys during that period causes the panel to sound a single
long beep. When the 15
-minute lockout period is over, a
Restore
message is sent to the
Central Station and recorded in the Event Log.
12
False Alarm Prevention
Many false alarms are caused by minor problems, such as a door left ajar when exiting the home.
Lyric
™ includes several features
to help prevent false alarms. Note that some are optional or must
be programmed by the installer. Disabling these features may increase
security, but might
also
increase the chance of false alarms.
Your installer can help you decide
how to use and customize
these features. A brief explanation
of false alarm prevention features follows, along with advice on what to do if false alarms
occur.
Exit/Entry
Delays
Programmed delay times allow you to leave after arming the system or
disarm it
after entering without setting off an alarm. Exceeding a delay period causes an
alarm.
After a false alarm, disarm the system and contact your monitori
ng company.
They will verify your security code or password, preventing unnecessary calls for
emergency response.
Alarm Reporting
Delay
Lyric is programmed to wait
for a brief period between sounding a burglary
alarm on the premises and sending an alarm message to your monitoring
company. This delay allows you to disarm the system before an alarm message
is sent in error.
Exit Alarms
False alarms can be caused by leaving the house and forgetting to close the
door. If this happens, Lyric sounds an alarm and displays an Exit Error.
The alarm reporting delay gives you time to disarm the system before an alarm
message is sent.
Exit Time
Restart
Exit Delay
Restart/Reset
If you leave the premises and enter again before the exit delay has expired, the
exit delay
restart
s, giving you more time to leave
without causing an alarm
.
With 10 seconds left to exit, the Controller
begins beep
ing quickly
, indicating
that
an alarm will occur if you don’t
exit or disarm
the system immediately.
If this occurs, disarm the system and arm it again when you are ready to leave.
Yo
u can restart t
he Exit Delay by pressing
Restart Timer
.
Silent Exit
Press
Silent Exit
to mute the beeping sound that accompanies exit countdowns
in most situations. Voice c
onfirmation of arming status is not muted. Silent Exit
increases
the Exit Delay time
.
Quick Exit
If the system has been armed and someone needs to leave the premises, you can
press this button, which restarts exit delay, allowing exit from the premises
without the need
to disarm and re-
arm.
Entry Delay
If the system is armed, this is the period
allowed between a door opening and the
system being disarmed with a user code. Failure to disarm the system during the
Entry Delay causes an alarm.
Delay period set by your
installer.
Exit Delay
Period that begins upon arming the system
, during which household members
can exit through entry/exit
doors without triggering an alarm.
Delay period set by
your
installer.
13
Arming the System
The Home button beneath the screen lights
green when the system is ready to be armed.
If the
button is blinking green, the system is not ready to arm.
Before arming your system, all protected doors, windows, and other protection zones should be
closed or bypassed (see
Bypassing Protection Zones
).
To change the volume of countdown sounds and security status voice announcements, see
System Settings
.
NOTE
When a security code is required, a valid code must be entered within 10 seconds of
pressing an Arm button. If an invalid code is entered, or more than 10 seconds elapses,
the
Security menu
returns and the system is not armed.
Arming states include
Arm
Away
For times when no one is home;
protects all perimeter and interior zones.
Arm Stay
For
times when the house is occupied;
protects
only perimeter zones.
Arm Custom
Arms the system with pre-
selected zones bypassed.
Bypass
This
feature allows you to arm the system while intentionally leaving
selected zones unprotected.
Arm Night
For times when the house is occupied;
protects perimeter zones and
interior
motion sensors if used. Other interior zones are unprotected.
Enabled by your installer and only used with interior motion sensors.
Instant
For times when
no one is expected to use the Entry/Exit
zone
doors
.
Entry Delay is eliminated
. When the system is armed, an
alarm occurs
immediately
if an exterior door is opened.
When arming
in Awa
y, Stay
, or Night (if enabled) modes,
Instant
mode can be
set from the Security screen (shown below)
. When using
Arm Custom
, use
the
Entry Delay button
on the Arm Custom menu to set Instant mode.
Quick Arm
Press
to arm the system in any mode
without entering a user code
,
if programmed
.
NOTE:
A user code is always needed to
disarm
the system.
Auto Stay
If you arm the system in the “AWAY” mode
but no one exits, the alarm system
automatically changes
to the “STAY” mode. This helps to prevent unwanted
alarms when someone remains on the premises. Disarm the system and Arm
Away again when you are ready to leave.
Enabled by
your
installer.
14
Arm Away
Security > Arm Away
By default,
this
mode’s exit delay countdown is accompanied by a beeping sound.
1.
Enter a
user code
or press
Quick Arm
. (If desired, click
Silent Exit
first.
)
2.
The system beeps
twice
and
announces “Armed Away; exit now”.
The exit delay
countdown
begins
.
Press
Restart
Timer
if you need more time to leave.
3.
Leave the premises
and close the door before the countdown ends.
4.
The system arms in Away mode. (Door and window sensors and interior motion
sensors are active.)
Arm Stay
Security > Ar
m Stay
By default, this mode’s exit delay countdown is silent
.
1.
Enter
a user code
or
press
Quick Arm
.
2.
The system beeps
three times
and announces “Armed Stay; exit now”.
The exit delay
countdown begins.
Press
Restart
Timer
if you need more time to leave.
3.
The system arms in Stay mode. Door and window sensors are active, but interior
motion sensors are not active.
Arm Custom
Security > Arm Custom
Use this option to pre-
set zones for bypass when arming the system. You can also enable or
disable the entry del
ay.
1.
Select Arm Custom to display a list of zones.
2.
Select the zones you wish to bypass when arming the system.
3.
Select Arm Custom on the bottom, right side of the zone list screen.
4.
Press
the Entry Delay button to s
et the
Entry Delay
On
or Off: Entry Delay On (the
button is blue)
, Entry Delay Off (the button is white)
. For
Instant Mode
, set
the
Entry
Delay
Off.
See
Insta
nt Mode
below
for more
details
.)
5.
Arm the system by entering a user code.
6.
The exit delay countdown begins.
7.
Leave the premises and close the door the same as
you would when setting Away
mode.
Bypassed zones are left unprotected.
NOTE
that the next time Arm Custom is used, the
same zones that were previously
selected
are highlighted on the zone list screen. If desired, select different zones for
custom arming.
Instant Mode
Security
>Entry Delay Off
OR
Security >
Arm Custom > de
-
select
Entry
Delay
In
Instant mode
, an alarm occurs immediately when a protected Entry/Exit zone door is
opened.
There is no entry delay time.
When arming in Away
, Stay
or
Night
(if enabled) modes, press
Ent
ry Delay
On/Off
at the
bottom of the
Security
screen
to toggle the option
Off
for
Instant mode.
When using
Arm Custom
, de-
select
the Entry Delay button located in the Arm Custom menu
for
Instant mode.
15
Arm Night
Security > Arm Stay
The
Arm Night
feature
must be enabled by your
security professional
.
1.
Select
Arm Stay
to display the keypad
.
2.
Select
Arm Night
and then enter a user code.
3.
The system beeps and announces “Armed Night Stay; exit now”.
The exit delay
countdown begins.
Press
Restart
Timer
if you need more time to leave.
4.
The system arms in
Arm
Night
mode.
Doors and windows and pre-
selected zones are
active.
Disarming the System
Security > Disarm
NOTE:
Disarming the system also
silences audible alarms and trouble alerts.
IMPORTANT SECURITY NOTICE
Your wireless key (key fob) is similar to your keys or
access card. If lost or stolen,
another person can compromise your security system. Immediately notify your
Dealer/Installer of a lost or stolen wireless key. The Dealer/Installer will then
remove the wireless key programming from the security system.
To d
isarm your security system:
1.
Select
Disarm
. A keypad appears.
2.
Enter a
user code. The system beeps and announces “Disa
rmed”, followed by
alerts about
system readiness
, if any
. The announcement “Check system” indicates a faulted sensor or
problems in the Cont
roller
itself
.
In most situations, if a valid user code is not entered within 30 seconds of pressing
Disarm
, the
Home screen
reappears
, and the system remains armed.
NOTES
:
•
If a valid code is not entered
by the time the
entry delay ends, an alarm
occurs.
•
The Guest code
and the Installer code
can only disarm the system if that code was
used to arm
the system. If the Quick Arm option has been used, neither the Guest
Code nor Installer Code can disarm the system.
Bypass
ing Protection Zones
Bypass
allows arming the system
while intentionally leaving selected zones unprotected.
Bypassed zones
will
not trigger an alarm.
NOTE
S
:
•
Fire and Carbon Monoxide (
CO
) and Panic zones
cannot be bypassed.
•
Bypassed zones are automatically un
bypassed when
the system is disarmed.
To Bypass zones:
1.
Before arming the system, press
Zones
on the
Security menu.
A list of your system
’s
zones
appears.
Faulted (open)
zones
are shown in red or orange.
Use the up and down arrows to scroll through the list of zones.
2.
Select the zone(s) to be bypassed.
3.
Press
Bypass
at the bottom of the screen
. A keypad appears.
At the bottom of the screen, you can
Bypass All Faulted
, which selects all zones with
faults or other issues.
Press
Select All
to toggle through options for selecting zones.
4.
Enter a user code. The zone list reappears
, with the Bypass icon
shown
for
the affected
zones.
16
Bypass
ing
Protection Zones
(continued)
5.
Arm the system as usual.
Press
Clear Bypas
s
to
un
-bypass
any previously bypassed zones. Any
zones with faults must be
addressed before arming the system.
Entry and Exit Delays
NOTE
:
Entry and exit delay times are programmed by your installer.
There is room to jot
them down
in
Your System
Information
, near the end of this guide.
Entry Delay
Entry
delay allows time to disarm the system when entering
the premises. If the system is not
disarmed
before the entry delay period ends, an alarm occur
s. If programmed, the Controller
beeps during the entry delay period as a reminder
to disarm the system.
Two
different
entry delay
periods
can
be
programmed. The first is for the
primary entrance,
typically, the front door. T
he second can be used for a secondary entrance, where more time
might be needed to walk to the Controller
to disarm the system.
Exit Delay
Exit delay begins immediately after the system is armed, providing time to leave through the
designated exit door without causing an alarm. In most situations, the touchscreen
displays a
countdown of the remaining time. The exit door must be closed before the end of the exit
delay.
Typically, the system beeps slowly when counting down to
Arm Away
; during the last 10
seconds of the delay period, the beeping speeds up. The exit beeps cannot be silenced
unless
Silent Exit
is selected.
Restart Exit Delay
The
Restart
Timer
button appears only if the option has been programmed by the installer
.
Exit delay can be restarted
once
.
Exit Alarm
This option helps minimize false alarms sent to the
monitoring company.
Exit Alarm must be
enabled by your installer.
Exit delay begins whenever the system is armed.
•
If an
exterior
door or protected
interior zone is faulted
during the exit delay (
and rema
ins
faulted
when the exit delay ends
), an
exit
alarm
occurs
and
an
entry delay
countdown
begins
.
•
If the system is disarmed before the entry delay ends, the alarm sound stops and the
message
Alarm Cancelled
and
any faulted zones
appear
.
•
No message is
sent to the monitoring company
. Any open zones must be secured
before the exit alarm condition can be cleared.
To clear the display, press
Disarm
and enter
a security code.
•
If the system is not disarmed
before the entry delay ends, and an entry/exit door or
interior zone is still open, the alarm sound continues and an
Exit Alarm
message is sent to
the alarm monitoring company
, along with a “Recent Close” message
(if
the
Recent Close
option
is enabled)
.
•
The message
Alarm Exit Error
appears
. Faulted
zones
are
also
displayed. The alarm will
continue to sound until the system is disarmed or timeout occurs
.
To stop the alarm,
disarm
the system
. The message
Alarm Cancelled
will be displayed.
“
Alarm
” and faulted zones
continue to be displayed.
To clear the display, press Disarm
and re
-enter the
security code.
An exit alarm (“Alarm –
Entry Exit”) also occurs if an entry/exit door or interior zone is faulted
within two minutes after the end of the exit delay.
17
Panic Alarms
Available
Panic modes may
vary,
depending on the options
programmed
by your installer.
IMPORTANT
Please note the difference between the Panic
button
below
the
touchscreen
and
the
different Panic
icons
on
the
touchscreen.
Activating a Panic Alarm
1.
Press and hold
the
button
on the Controller
until Panic icons appear
on the screen
.
2.
Press the appropriate Panic icon on the screen.
Depending on the Panic mode selected, an alarm tone sounds and the appropriate alarm icon
appears on the
touchscreen.
Pressing
Police
typically sends a
silent
message to your monitoring company
*. When you
take your finger away from the Police icon, the screen
appears to return to a normal state
,
with the
button on the Controller blinking. However, the alarm message has been sent.
*
The details of this function’s
behavior
are
determined by a setting in the system’s programming; we
recommend that you verify the setting with your installer.
Common
Panic Icons
Fire
Alerts the
monitoring company that a fire condition exists.
(Displays zone
995)
Police
Alerts the
monitoring company that a police emergency exists.
(Displays zone
999, default is silent)
Medical
If programmed, alerts the
monitoring company to other types of emergency.
(Displays zone
996)
Local
Activates sirens and sounders on premises without alerting the monitoring company
.
(Displays zone
998)
Types of Panic Alarms
Silent
emergency
(silent alarm
)
Sends an alarm signal to the monitoring company, but triggers no audible alarms
or
touchscreen
display.
Requires connection to a monitoring company.
Audible
emergency
(audible alarm
)
Sends an emergency message to the monitoring company, if connected. A
loud, steady tone sounds at the Controller and external sounders if
connected, and an alarm app
ears
on the touchscreen
.
Personal
emergency
or
Aux
alarm
Sends an emergency message to the monitoring company if connected and
sounds at the Controller, but not at external sounders. An alarm icon appears
.
Fire alarm
Sends a fire alarm message to the monitoring company
if connected
. A
unique tone sounds at the Controller and external sounders are activated if
connected. A Fire alarm icon appears
.
Local alarm
If programmed, activates the sirens and sounders on the premises without
sending a message to the monitoring company.
Cancelling a Panic Alarm
NOTE
A Fire alarm triggered by
the Controller’s Panic button
cannot
be cancelled from
remote services such as Total Connect
®. For your safety, Fire and Carbon Monoxide
alarms can only be cleared/silenced from the Controller itself.
Depending on
the
type
of panic alarm in effect
, a keypad may appear immediately after the
alarm is initiated.
1.
Enter a user code
to cancel the alar
m.
2.
The
audible
alarms stop and
Alarm Cancel
appears
.
18
Cancel
ling a Panic
Alarm
(continued)
If a silent alarm has been
activated
and the Home
screen is displayed:
1.
Select
Security
on the Home screen. Typically, a
Disarm
icon appears;
a Security status
message such as “Not Ready To Arm” may be displayed.
2.
Press
Disarm
. A keypad appears on the touchscreen
.
3.
Enter a user code.
4.
The normal Security
menu
returns and the
butt
on on the Controller
stops blinking.
Clearing a Panic Alarm
After a panic alarm is cancelled, the Controller
continues to display
zone information
associated with the alarm (this
feature
is known as
Memory
of
Alarm
).
To
cancel and
silence the alarm, enter a user code.
To clear memory of
alarm on the screen:
1.
Press the Home
button beneath the screen.
2.
Re
-enter the user code.
Memory of alarm can also be dismissed with these steps
:
1.
Cancel and silence the alarm with a user code as above.
2.
Select
Zones
on
the
Security menu. The zone number ass
ociated with the type of
alarm
appears
.
3.
Press
Clear Alarms
at the bottom of the screen.
4.
Enter
a user code. The Zones screen displays “
No items to display!
”
5.
Press
to return to the Security menu
or press the Home
button.
Chimes
/Voice Annunciations
IMPORTANT
The Chime feature is intended for convenience and is not intended for life safety
purposes or pool alarm and does not meet the requirements of UL 2017.
Volume/Mute
Home > Settings
NOTE
S
•
Chime and voice volume/muting can only be changed when the
system is disarmed.
•
Voice annunciations
are controlled by enabling or disabling Chimes.
•
Voice annunciations should not be confused with Lyric’s
Voice Command
or
Audio Alarm Verification
features.
Lyric
™ can
give audible
notifications
when a protected zone
opens
while the system is
disarmed
. With Chimes enabled
three beeps
(or a selectable tone)
sound
at the Controller
when a protected zone
is opened.
If programmed
, a voice announcement
also sounds.
1.
On the Home screen, select
Settings
.
2.
Select
Chime
to enable chime sounds and voice annunciations
. To mute all, de-
select.
For
chime sounds only, de-
select
Voice.
3.
Adjust
volume with the slider.
4.
Press
Save
.
Setting Chime
Sounds
Home > Security > Zones
NOTE
S
:
•
Chime sounds can only be changed when the system is disarmed.
•
Sounds can be changed only for door, window and motion sensors. Sounds
associated with s
moke and CO
detectors cannot be changed.
Different sounds ca
n be assigned to the sensors in your system.
1.
On the Zones menu, press
Select All
repeatedly
to choose
Select Chime
. A list of
sensors appears.
2.
Select a sensor
. The Controller displays available sounds.
3.
Press repeatedly to choose a sound. (Options include
Disabled
.)
4.
Press
to save your selection and return to the Security menu.
19
Audio Alarm Verification
(Two
-Way Voice
)
This feature allows your central monitoring station to listen to or talk with
persons
on the
premises when an alarm has occurred.
NOTES
•
System announcements are disabled when this feature is active.
•
Fire and CO alarms will prevent Audio Alarm Verification from operating.
•
New Fire or CO alarms will terminate Audio Alarm Verification
operation.
•
Burglar alarms occurring during Audio Alarm Verification operation do not interrupt
operation and are reported immediately after operation concludes.
•
Audio Alarm Verification modes are controlled by the central station.
Built
-In Camera
Lyric’s built
-in camera takes a snapshot of the person at the Controller
when the system is
manually
disarmed.
Snapshots can be viewed via
your
Total Connect
® account
.
Built
-in camera options may
vary.
Ask your security professional
for more information.
20
21
Automation: An Introduction
Home > Automation
IMPORTANT
Automation can ONLY be used for lifestyle enhancement. It must not be used for personal safety
or property protection.
Smart Scenes
Smart Scenes can
automate Lyric
™ functions for security,
comfort
and
energy savings
by
controlling your system’s connected
devices. A single command can make
multiple
settings
. For
example:
•
Selected
lights can respond to a door opening or movement in the middle of the night
•
Climate settings can be controlled by your family’s schedule
•
The
security system can disarm automatically for e
xpected visitors or babysitters
Selected functions can be restricted to the homeowner, and limited access given to children or
guests.
If you subscribe to Honeywell’s
Total Connect
®
remote services, you can create and manage
Smart
Scenes
remotely from mobile devices or any PC with an internet connection.
Without
a Total Connect
account
, you can create and manage Smart
Scenes
from the Lyric
Controller.
See
the
Smart Scenes
section for more.
Voice Command
You can control a variety of Lyric functions
by speaking to the Lyric Controller in plain language.
Voice control requires that Smart Scenes
be set up and linked to specific
spoken phrases
.
See the
Voice Command
section for more.
Z-Wave Devices and Lyric
Z-Wave
® devices
such as
switches,
locks
and garage door openers
can be controlled by Smart
Scenes or activated
manually from
the Lyric Controller
. Lyric can operate
as many as 72 Z-
Wave
devices; they are sold
separately and added
to your system through a process
called “
Inclusion
”.
See
page
33
or
more
information.
A list of Z
-Wave devices that have been tested with Lyric can
be found on
page
40
.
22
23
Automation: Smart Scenes
Home > Smart Scenes
IMPORTANT
When
the Controller
is connected to
Honeywell Total Connect™
(or other
compatible remote services)
, Smart Scenes can be
created and modified ONLY via
remote services
.
Smart Scenes can be created, deleted or edited ONLY by the Master User. See
Smart Scenes and User
Access
for more about
types
of users and their
access to different functions.
Three types of Smart Scene can automate combinations of security and comfort
settings:
•
Anytime
: Initiated by users.
•
Triggered
: Initiated by the system in response to user
-def
ined conditions.
•
Scheduled
: Initiated by the system’s calendar and clock.
Smart Scenes are frequently used in pairs. For example, a Smart Scene might
be set to operate
multiple devices, turning on lights and opening blinds or shades. A second Smart Scene could be
used to return these devices to their Off or closed states.
NOTES
•
As many as 100 Smart Scenes can be created.
•
You can modify (
Edit
), manually start
(Run
) and review (Show)
Smart Scenes
prior
to operation.
•
Scheduled and Triggered Smart Scenes can be paused with the Hold
function.
•
Setup details vary with each type of Smart Scene.
•
Many buttons in Smart Scenes toggle through different options when pressed
repeatedly.
•
The system treats security
(Arm/Disarm)
actions
separately
from changes to
devices such as lights, locks and thermostats.
Setup details with options of both
types display them
in different
categories called Security and Devices.
Smart Scenes and User Access
NOTES
•
The Master User designates which types of user have access to each Smart Scene.
See
Users and Security Codes
for more information on different types of users.
•
Smart Scenes can be created, deleted or edited ONLY
by the Master User.
•
The
Add New
button is available only to the Master User.
Regular users can Run and Show Smart Scenes created for Regular Users and Guests as well as
those designated “All Users”
. Guests can Run and Show Smart Scenes created for Guest
s as well as
those designated “All Users”.
To work with Smart Scenes
at the Lyric
™ Controller
:
1.
Select
Smart Scenes
on the Home screen. A keypad appears.
2.
Enter a user code to display the Smart Scenes menu. From here, Smart Scenes can be
created or viewed by type.
24
Creating a Smart Scene
These instructions apply to the creation and operation of Smart Scenes from
the
Lyric
™
Controller’s
screen.
As above,
if your system is connected to Total Connect
® remote services, you
can create Smart Scenes only through Total Connect. Working with Smart Scenes from Total
Connect differs slightly.
(
Note that
Anytime
scenes are labeled as “When you manually run this
scene” or “When you click it” in Total Connect.)
Creating any Smart Scene involves these settings:
•
Name
•
The type of trigger that initiates the Smart Scene
•
The type of user who can
manually
run the Smart Scene
•
The resulting action(s) that take place when the triggering events or conditions occur
NOTE
Creating a Smart Scene should begin with giving it a
Name
.
1.
Select
Add New
. (The default name
that appears
may differ from the illustration.)
2.
Press
Name
.
3.
Use the onscreen keyboard to enter a name and
Save
it.
4.
Select the type of user who can run the Smart Scene. Choices include:
•
Master
•
Regular Users
•
Guest
•
All Users
5.
Press
Action Type
to toggle through the types of Smart Scene.
a.
Anytime
: Go to Step
#
6
.
b.
Scheduled
: Go to Step
#7
.
c.
Triggered
: Go to Step
#8
.
6.
Select
Anytime
. These options appear:
•
Name
•
Action Type
•
Who can run this Smart Scene? (User
type
)
•
New Action
a.
Press
New Action
to define the
system’s
response when the Smart Scene
is
triggered.
b.
When settings are complete, press
until the Smart Scene appears with its name
displayed.
c.
Press
Save
. Press
to return to the main Smart Scenes menu.
25
7.
Select
Scheduled
.
a.
Select the type of user who can run the Smart Scene.
b.
Select
Scheduled
to display clock and calendar settings.
c.
Set a time when the Smart Scene will start. Be sure to specify
AM or PM.
You can select
Sunrise
or
Sunset
instead of setting a time on the clock. Selecting
Sunrise or Sunset overrides the clock controls.
NOTE
that updated Sunrise and Sunset times
may depend on the system’s connection
to the internet or cellular phone network. Ask
your
installer
for more information.
d.
Set the days of the week for the
Smart Scene to take place.
e.
Press
Save
. The schedule settings are displayed.
f.
Press
New Action
to define the response when the scheduled time occurs (see Step #8).
g.
Press
to return to the Smart Scenes
menu.
8.
Select
Triggered Action
. These options appear:
Smart Scenes can be started by one or a combination of the following options:
•
Event Zone Type
•
Restore Zone Type
•
Trigger
•
System Operation
NOTE
S
Event Zone Type
,
Restore Zone Type
and
Trigger
can be
different kinds of
conditions.
For example, a given Smart Scene can be triggered by a Fire a
larm OR by an
Entry/Exit event. Smart Scenes can also be triggered by Trouble conditions
(Trouble as the Trigger in one of the system’s zones).
Device-
relate
d events (such as Light On, Light Off, Door Locked, Door
Unlocked) set the button at right to
Device
. Choices depend on the devices
installed in your system.
a.
Event Zone Type
starts the Smart Scene in response to any event (Fault, Trouble
or Alarm) in any
protected Zone
of a specific zone type.
Select the desired
option.
Examples of some
typical zone types include:
•
Entry/Exit (front and back doors)
•
Perimeter (typically window sensors)
•
Interior Follower (typically motion sensors)
•
Day/Night (Usually assigned
to
sensitive
area
s where immediate notification of an
entry is
always wanted
.)
•
24 Hour Silent (Panic button)
•
24 Hour Audible (Panic button)
•
Silent Burglary (typically a sensor)
•
Fire No Verification (smoke detector)
•
Fire With Verification (smoke detector)
•
Carbon Monoxide (CO detector)
NOTE
: Your system may include Zones that do not offer every Zone Type response.
26
b.
Restore Zone Type
starts the Smart Scene when any zone with the selected Zone
Type
returns to its normal state (
such as a door closing). The opti
ons are the same
as
Event Zone Type
options.
NOTE
: Event Zone Type and Restore Zone Type are
separate settings
. For
example, a given Smart Scene can be triggered by a Fire Alarm (Fire No
Verification as the Event Zone Type) OR by an open door closing (Entry/Exit as the
Restore Zone Type).
c.
Trigger
starts the Smart Scene in response to a Fault, Trouble or Alarm in a
particular zone or
changes to connected devices.
A note about triggering events
:
Any change in the state of a security system zone is known as a
Fault
. Faults can
include
Trouble
and
Alarm
conditions. Trouble can include low battery or loss of
communication with the device. Alarm
conditions include zone faults while the
system is armed and fire/CO sensors. Fault, Trouble and Alarm conditions can be
used to trigger a Smart Scene.
Fault:
Any
change in the state of a sensor triggers the Scene.
Trouble:
Only
Trouble
conditions trigger the Scene
Alarm:
Only
Alarm
conditions trigger the Scene.
Choosing
one of these
events
sets the button at right to display
Zone
options.
Smart Scenes can also be
triggered by changes in connected
devices
such as lights
and locks. These events include:
Light On
Light Off
Door Locked
Door Unlocked
Choosing
one of these
events
sets the button at right to display
Device
options.
d.
Choose
Zone
or
Device
, depending on
your selection of a Trigger above.
Security
zone sensors or devices such as lights and locks are listed.
e.
Select the zone or device and
Save
.
f.
System Operation
starts Smart Scenes in response to security
-related events.
Examples of
some available options
include:
•
Arm Away
•
Arm Stay
•
Disarm
•
Any Burglary Alarm
•
Bell Timeout (end of the programmed time for which an alarm sounds)
•
Start of Entry Delay
•
End of Exit Delay
•
Any Fire Alarm
g.
Select
New Action to define the response when the triggering event occurs.
NOTE
: The 24 Hour Silent Alarm or 24 Hour Auxiliary Alarm Zone types will not
trigger the selected Smart Scene if the
Any Burglary Alarm
option
is programmed.
9.
New Action
defines the response when the triggering event occurs. This includes
users manually runnin
g
Anytime
Smart Scenes, the time of
Scheduled
Smart Scenes
and the conditions for
Triggered
Smart Scenes. You can choose both Security and
automation
device responses. The Security choices are:
•
Arm
the system in Away
mode.
•
Arm
the system in Stay
mode.
•
Disarm
the system.
a.
After choosing a Security setting, press
and then
Save
.
b.
If you choose to work with Devices, a list of the system’s automation devices appears.
c.
Select one or more devices and set the device’s desired operation. (For example,
set switches to on or off, or locks to locked or unlocked.)
27
d.
After adding a device and its desired operation to the Smart Scene, press
Save
.
Other available devices are displayed again so that they can be added to the Smart
Scene.
NOTE
: In most situations, specific Security and Device information is displayed by
pressing
the Down arrow.
10.
Press
Save
.
11.
Press
to return to
the
Smart Scenes menu.
Hold/Run/Show
These
controls
allow you to pause, preview/execute and review Smart Scenes from the Lyric
™
Controller.
NOTE
Even
if you use
Total Connect
® and can only
create and edit
Smart Scenes via Total
Connect
, you
CAN
use the
Hold, Run
and
Show
fun
ctions from the Controller.
Hold
Hold
allows Scheduled and Triggered Smart Scenes to be temporarily suspended.
A
Scheduled
Smart Scene can be put on Hold
before
programmed operations take place.
1.
Select a Scheduled or Triggered Smart Scene.
2.
Press
Hold
. The button is highlighted, and programmed operation will not take place.
To remove a Hold:
1.
On
the Smart Scenes
menu,
enter a user code with access to the desired Smart Scene.
2.
Select the Smart Scene
and
un-
highlight
Hold
. Programmed operation will resume.
Run
Smart Scenes can be manually started with the
Run
button. The Smart Scene’s results are
displayed when the programmed operations have been performed.
NOTE
The
Run
option
can be used to check the outcomes of
Scheduled
Smart Scenes and
Triggered Smart Scenes, regardless of programmed triggers.
1.
Select
the
Smart Scene.
2.
Press
Run
. The system performs the programmed operations and the results are
displayed. Successful operations are displayed with device information and a
check mark.
Failed operations are displayed with an empty circle.
Show
(Review)
Use the
Show
button to see the programmed details of a Smart Scene without running it.
1.
Select
the
Smart Scene.
2.
Press
Show
. The scene’s category, authorized users and included devices are displayed.
28
29
Automation: Voice Command
Home > Security > Tools > Voice Command
Not to be confused with voice annunciation of system status
(Home > Settings)
.
Voice Command offers control of Smart Scenes
and Video by speaking in plain language. User
-
selected
trigger phrases
spoken near the Controller alert the system to listen for further instructions.
Five
command phrases
can be assigned to trigger Smart Scenes.
Assignable command phrases are
listed in t
he
Voice Command Assignment
section.
The command phrase “Cameras” controls the
Video function exclusively.
NOTES
•
Voice Commands can only trigger Smart Scenes and launch the Video function. Voice
control of indiv
idual devices must be part of a Smart Scene triggered by voice.
•
Voice commands
cannot disarm the system in a single step
. If a Smart Scene that
disarms the system is triggered by voice command,
a user code is required
.
•
Verbal responses are available in English only.
•
We
suggest enabling
Trigger Feedback
(
F
, below
) until you are familiar with
Voice
Command.
However
, Voice Command can
be used without Trigger Feedback.
•
The Controller is designed to hear commands spoken in a normal voice from about 10
feet away. Background noise may affect Lyric’s ability to recognize commands. You
may need to speak louder or move closer when there is a lot of background noise.
Adjust
the
system’s responsiveness using
the Command Sensitivity and Trigger
Sensitivity sliders along with settings on the Counter menu. See
Counter
(Sensitivity Settings)
.
•
You can test voice recognition without s
etting up Smart Scenes by going to the
Home screen and saying your trigger phrase.
Set
up
NOTE
The system should be disarmed before setting up Voice Command.
A.
Familiarize yourself with using Voice Command.
B.
Assign Smart Scenes to command phrases.
C.
View a record of Voice Command events.
D.
View and adjust sensitivity settings. See
Counter (Sensitivity Settings)
, following.
E.
Turn Voice Command on and off.
F.
Turn verbal confirmation of trigger phrases on and off.
G.
Select one of the three available trigger phrases.
H.
Adjust sensitivity to command phrases to compensate for varying noise conditions.
I.
Adjust sensitivity to trigger phrases to compensate for varying noise conditions.
J.
Set volume of trigger feedback (verbal responses to your commands)
A
H
I
J
E
F
G
B
C
D
30
Voice Command Assignment
Voice Commands must be assigned to existing Smart Scenes to function. See
Smart Sc
enes
for
more information.
NOTES
•
Only
the “Cameras” command is active without setup. It is not included in the
assignable commands listed below.
•
Only
one Smart Scene can be associated with a given voice command.
1.
On the Voice Setup screen, select Voice Control. The
assignable command phrases
are
displayed:
2.
Touch a command in the list and press
Select
. A list of Smart Scenes appears.
3.
Select the Smart Scene to trigger with the command phrase and press
Save
.
4.
The li
st of command phrases appears, showing the associated Smart Scene.
5.
Press
to return to the previous
screen.
6.
Press
to return to the Tools menu
OR press the
button below the touch
screen
to
return to the Home screen.
Clearing or Changing a Voice Command
1.
Select a command phrase with an assigned Smart Scene.
2.
Smart Scenes are listed.
3.
Press
Clear
.
OR
4.
Select a different Smart Scene.
5.
Press
Save
.
Using Voice Command
1.
After initial setup, speak the selected trigger phrase (“H
ello Lyric”, “Hello Lyric Home”
or
“Okay Lyric”).
2.
Lyric
™ confirms “Hello
; please
say
your command” (if trigger feedback is enabled) and
awaits a command phrase.
3.
Speak a command phrase. If Trigger Feedback is enabled, Lyric confirms that it is
processing
the
command.
4.
Lyric runs t
he assigned Smart Scene or opens t
he Video function.
31
Counter (Sensitivity Settings)
Press
on the Setup menu.
This screen summarizes the interpretation of trigger and command phrases heard by the system.
Count
Displays the number of times a trigger or
command has been heard b
y the
controller
.
Accuracy
The user
-
set level of sensitivity to spoken trigger and command phrases.
Last 10
Accuracy
Represents the accuracy with whic
h Lyric
™
has interpreted
the
last 10 voice
commands. These figures are based on
internal diagnostics.
Accuracy values
range from
1-2000.
Clear
Resets the
Count
and
Last 10 Accuracy
values for a single trigger or
command phrase.
Clear All
Resets the
Count
and
Last 10 Accuracy
values for all trigger and command
phrases.
Adjusting Se
nsitivity
If users need to repeat commands or speak abnormally loudly, Lyric’s responsiveness can be
improved by changing the
Accuracy
value.
1.
On the list shown above, select the
desired
phrase.
2.
Find the phrase’s lowest
Last 10 Accuracy
number.
3.
In the
Accuracy
column
, press
the
displayed
number
. A keypad appears.
4.
Enter a number moderately higher than the number cited in step #2. For example, if
the lowest Last 10 Accuracy number is 599, set the counter for 800.
5.
Press
Done
.
If the results are
unsatisfactory, try entering a higher
or lower
number.
Experiment
with these
settings and the
Command
and
Trigger
Sensitivity
sliders for best performance.
32
33
Automation: Z
-Wave Devices
NOTE
Z
-
Wave automation functionality is supplementary only and has
not been
evaluated by
compliance agency
.
Z-Wave
® technology is designed to automate devices in a home control network.
The
Lyric
™
Controller
is a security enabled Z
-Wave device that supports Z
-Wave Network Wide Inclusion
(NWI) Mode.
The
Controller
and Z
-Wave devices add
ed to your system
are linked together in a wireless
network. Each device in the
network is assigned a unique address and cannot be activated by a
neighbor's Z
-Wave controller. The Z
-Wave
network supports multiple controllers, allowi
ng Z
-
Wave
remote controls to be used throughout the home.
NOTE
:
In some cases, a
Z-Wave device might
not report its status to
the
Lyric
Controller
when
an action is initiated at the device itself. This varies with the manufacturer.
Press
Automati
on
on the Home screen. The
Z-Wave Device Management menu
appears
, initially
displaying
categories of Z
-Wave devices. (
Your
Controller
’s display may differ from these
illustrations.)
This screen may also display “
Press to see Failed Devices
”. See
Failed Devices (Failed Nodes)
for more information.
Press
the
Down
arrow for more options
:
Consult your installer
about the
options available in your system.
Selecting a device category opens a list of devices in that category.
An example of the
Switch
category is pictured.
For
most
devices, status is indicated by the color of the icon.
The
Refresh
button
updates device status indications on the display
.
34
Operating Z
-Wave Devices Manually
1.
On the
Z-Wave
® Device Management menu,
select
one of the device categories.
2.
Select the device you wish to operate. Controls appear.
3.
Lighting controls might offer an On/Off button or a slide control for dimmers.
4.
Thermostats may display temperature set points and energy
-saving features. The
options shown will vary with your device.
5.
Operate the device as desired.
6.
Press
to return to the previous screen.
Adding
Z-Wave Devices (Include)
NOTE
When adding a device, it may be necessary to perform the
Exclude
procedure
before the
device can be
Included
successfully
.
1.
On the
Z-Wave Device Management menu, press the Down arrow.
2.
Press
Tools
.
3.
On
-screen
options
appear, including Include
Devices
, Exclude Devices
and
Advanced
Tools
. ( View Failed Devices
may also appear.)
4.
Select
Include Devices
.
5.
The panel enters Inclusion mode. Next, the panel displays “Ready to Include device.
Press the function button on device”.
6.
Press the device’s Function button within 60 seconds. (Note that the location of the
Function button varies with the device you are adding. See the device’s instructions.)
7.
The panel displays “Device Found.
Please Wait”.
8.
To include additional devices, repeat step 5.
OR
Press
Abort
to complete the Inclusion process.
9.
Press
to retu
rn to the previous screen
.
Including Light Switches or Outlet Modules
Install the receptacle, wall switch or lamp/appliance module
before
Including it in your
system.
Refer to the device’s instructions for more information about installation.
Z
-
Wave
switches and outlet
modules may vary
. Refer to
the
device’s instructions
to ensure
that
it is
Included
properly
in your system
.
Including Door Locks
IMPORTANT
For security, Z
-Wave door locks are encrypted
; they enroll at low power
transmission range
(approximately 6 feet). This
requires
Including the lock before
its installation in a door.
Assemble the lock, connect necessary cables and install batteries according to the
device’s
instructions.
Be sure the door lock’s orientation/handedness is correct
.
Z-Wave door locks vary. R
efer to the
device’s instructions to ensure
that it is Included
properly
. See
Users and Security Codes
for more information.
After Inclusion, install the lock within
recommended
Z-Wave range (
see
Wireless Range
for
more
information).
NOTES
•
Program the 4
-digit
user code
into
the
Controller
. When programming user codes
into
the Controller
, determine if the user will have access to the Z
-Wave lock. If
so, the us
er code will be transferred to the lock.
•
If using
a lock
with
Smart Scenes, automatic locking/
re-locking features should be
disabled.
•
Due to Low Power Inclusion Mode of secure devices, Include the Z-
Wave Lock
first, if not using an Inclusion Tool/Remote Control. The lock should be installed
before including other devices.
•
During operation, the system will display “JAMMED” and will revert to “Unlocked”
status if a jammed lock is detected.
35
Including Thermostats
Install
and
test
thermostat
s before
Including
them
in your system.
Refer to the device’s
instructions for more information about installation.
See
Notes on Thermostats
for
more
information about
using thermostats with Lyric
™.
Deleting Z
-Wave Devices
(Exclude)
To delete (Exclude) a Z
-Wave
® device:
1.
On the
Z-Wave Device Management menu, press the
arrow.
2.
Press
Tools
.
3.
Select
Exclude Devices.
4.
The panel
enters Exclusion mode. Next, the panel displays “Ready to Exclude device.
Press the function button on device.”
5.
Press the device’s Function button.
6.
The device is excluded from the system and its information is displayed.
7.
To delete another device, press
E
xclude
on the right side of the screen.
OR
Press
to return to the previous screen(s).
Editing
Z-Wave Device
Names
1.
On the
Z-Wave Device Management menu,
select
the category that includes the
device you want to rename.
2.
Select
the device in the displayed list.
3.
The device’s controls appear, showing the device’s default name.
4.
Press
Edit
on the right side of the screen.
5.
A keyboard appears on the
touchscreen.
6.
Press
Clear
to delete the default name.
7.
Enter a custom name, using as many as 14 characters.
8.
Save
the device’s new name.
9.
When you are finished editing,
press
to return to the previous screen(s).
Advanced Tools
1.
From the
Z-Wave Device Management menu, open
Tools
.
2.
Select
Advanced Tools
.
3.
Enter the Master User code. The Advanced Tools screen appears
:
View Enrolled Devices
Press
to display Z
-Wave device information: System Index/name, Secured or Non
-Secured,
device type, device ID, manufacturer, node number.
36
View Enrolled Controllers
Press
to display controller information: Primary or Secondary, Z
-Wave Library Rev., Home ID,
device type, device ID, node number, manufacturer, Secured or Non-
Secured.
Reset Controller
Press
to delete all Z
-Wave
® nodes in the Controller
, and reset the
Controller
’s Home ID.
When
prompted, press
Yes
to confirm.
Note
that resetting the
Controller
does
not
delete/Exclude individual Z
-Wave devices. Therefore,
each device must be Excluded before being added/Included in the
Controller
again.
Pri. Controller Shift to Secondary
Press
to
designate another controller
(such as a Z
-Wave remote control)
as the Primary
Controller.
When the panel displays “Shifting”,
start the “Learn” function on the s
econdary controller.
Refer to the secondary controller’s instructio
ns for more information.
NOTE
Both
controllers can operate the system’s Z
-Wave de
vices, but only the Primary
can
Include/Exclude devices.
Locking Door
Press
to have your system
arm
automatically when a Z
-Wave door lock is locked.
Press
repeatedly
to
select
Away
mode
,
Stay
mode,
Arm without Auto
-
Stay
mode
or to
Disable
this option.
Learn
This function is usually
performed on a control panel or Z
-Wave remote control being added to the
system as a
secondary controller
OR
on a secondary controller being designated as Primary.
Press
after starting the Include or Shift Control function on the primary controller.
All Devices Off
Press
to manually turn
off all Z
-Wave devices.
NOTE
: Some thermostats may enter
Energy
Saving mod
e
. Devices of different types will react differently to the “All Devices Off”
command. Refer to your Z
-Wave device’s instructions for more information.
.
All Devices On
Press
to manually turn on all Z
-Wave devices.
NOTE
: Some thermostats may
exit
Energy
Sa
ving mode. Devices of different types will react differently to the “All Devices On”
command. Refer to your Z
-Wave device’s instructions for more information.
Failed Devices
(Failed Nodes)
When the system tries to operate a Z
-Wave device that has no AC power
or other problems,
it is identified as a
Failed Device
. The system may take up to a minute after the operation to
recognize
the failure.
To view Failed Devices:
1.
On the
Z-Wave Device Management menu, select
View Failed Devices
. The panel
displays “
Fai
led Nodes Found!
”
2.
Press
OK
.
3.
The device’s information is displayed. If multiple devices are listed, use the up and
down arrows at right to view the entire list.
NOTE
:
When troubleshooting
a failed device
, first make sure
its
power has been
restored.
If a device is defective or otherwise unavailable, use the
Fix All
option.
1.
Select Fix All on the right side of the screen. The system displays “
This will delete all
failed nodes.
”
2.
Press
Yes
to confirm.
Devices deleted with Fix All must be added to the sy
stem again. See
Adding Z
-
Wave
Devices (Include)
.
Failed Z
-Wave devices are also indicated by a
symbol on the Z
-Wave Device
Management menu
or the
symbol appearing in gray on the Home screen.
37
Garage
Doors
Home > Automation > Garages
Garage door operation from the Controller requires installation of a garage door control kit.
Consult your security professional for more information.
The Lyric
™ Controller can remotely operate and monitor as many as four
garage doors.
The
system
can be armed when the garage door is open
ed. After it is closed, the zone will be
monitored
without providing burglary protection.
The Controller can automatically close garage doors if left open for more than a given time period
(
Close in
)
or at a specified time (
Close at
). Garage doors can also be programmed for monitoring only.
IMPORTANT
Do not use
Lyric’s
garage door automation with any garage door opener that lacks the
safety features required by U.S. federal safety standards
(this includes any garage door
opener model manufactured before January 1, 1993). A garage door opener that cannot
detect an object and stop and reverse the doo
r does not meet current U.S. federal safety
standards. Your garage door opener also must signal
before unattended door operation.
For more information please consult your garage door opener manual.
NOTE
Press
Switches
on the Automation Management menu to configure new Z
-Wave
®
binary garage door opener
s. Ask your security professional for more inf
ormation.
Garage Door Operation from the Lyric Controller
1.
On the Home screen, select
Automation
.
2.
On the Automation Management menu, press
Garages
. The Controller displays the
Open/Closed status of your connected garage doors.
3.
Select the garage door you wis
h to operate.
4.
Press the button in the middle of the screen to open or close the garage door.
Close in
Use the keypad to set a specific time to wait before an open garage door
closes automatically (maximum 12 hours and 59 minutes). Use leading zeroes
when entering a number of hours less than
10
(“09:15” or “00:45”). Press
Done
to save.
Close at
Use the keypad to set a specific time of day that an open garage door closes
automatically. Remember to specify AM or PM. Press
Done
to save.
Edit
Press to rename the selected garage door.
Use the on-
screen keypad and press
Save.
NOTE
:
The Lyric Controller does not support the status LED on the garage kit’s relay
module (Honeywell 5877).
38
Important Notes About Z
-Wave Devices
WARNING: NOT FOR USE WITH MEDICAL OR LIFE SUPPORT EQUIPMENT!
Z
-
Wave
®
enabled devices should never be used to supply power to, or control the
On/Off status of medical and/or life support equipment.
•
Some Z
-Wave devices may not communicate low-
battery notifications to the Lyric
™
Controller. Please pay attention to low battery
indications on individual devices and
replace batteries when the notifications appear.
•
When
performing
a command directly from a
thermostat or water shutoff valve, a
change
of status
message may not appear at the C
ontrol
ler.
Wireless Range
This device complies with the Z
-Wave
®
standard of open-
air, line of sight transmission
distances of
79
meters (
260
feet)
. Actual performance in a home depends on the number of
walls between the controller and the destination device, the type of construction and the
number of Z
-Wave enabled devices installed in the control network.
Note
that Z
-Wave home control networks are designed to work properly alongside wireless
security sensors, Wi
-Fi®, Bluetooth and other wireless devices. Some 900MHz wireless
devices such as bab
y cams, wireless video devices and older cordless phones may cause
interference and limit Z
-Wave functionality.
Things to consider regarding RF range:
•
Each wall or obstacle (refrigerators, large TVs, etc.) between the remote and the
destination device can reduce the maximum range of 30 meters (
100 feet
) by
approximately 25
-30%.
•
Brick, tile or concrete walls block more of the RF signal than walls made of wooden studs
and drywall.
•
Wall
-mounted Z
-Wave devices installed in metal junction boxes will suffer a significant
loss of range (approximately 20%) since the metal box blocks a large part of the RF
signal.
Additional Z
-Wave Information
•
Lyric can control up
to
72
Z-Wave devices.
•
The system supports a maximum of 232 nodes. Note that a node is created every time a
device is Included, even if the device is being re-
added to the system after being
Excluded. This can cause the number of nodes in the system to exc
eed the number of
actual devices.
•
If the limit of 232 nodes is met and you need to add or re-
Include more Z
-Wave devices,
use the Reset Controller function. Be aware that resetting the controller deletes all of the
system’s nodes, requiring all devices t
o be Included again. Node numbers can be viewed
by selecting Automation > Tools > Advanced Tools > View Enrolled Devices. Remember
that the system may require the Master User code for access to Advanced Tools.
•
The system is not aware
of door locks being enabled with any temporary user shutdown
feature such as Vacation Mode. The system will continue to unlock a door if programmed
to do so via Smart Scenes.
•
Z-Wave door locks with thumbturns: Certain models allow a brief period in which the
thumbturn can be operated manually before the device locks automatically. Locks of this
type are not recommended for use with Smart Scenes.
39
Notes on Thermostats
IMPORTANT
Honeywell is not responsible for property damages due to improper setting
of thermostat modes.
•
If Lyric
™ is linked with Total Connect
®, 7 -day schedules saved in Total Connect will not
affect thermostat operation.
•
In each thermostat used (as many as 6), both of the thermostat’s Zones must be
programmed. The pairs of zones are listed here:
1
280 & 281
4
286 & 287
2
282 & 283
5 288 & 289
3 284 & 285
6
290 & 291
•
Setback
allows you to set the temperature that you wish to maintain after running a
Smart Scene. After the Smart Scene runs, the temperature stays the same until it is
changed manually or by another Smart Scene running that sets a different temperature.
Setback
does
not
change thermostat modes (Off/Heat/Cool/Auto, etc.) when a Smart
Scene runs
.
•
When controlling a Z
-Wave
® thermostat from the Lyric Controller, make sure the
thermostat’s
scheduling
feature is disabled on the thermostat itself
.
•
When the HOLD button on Lyric’s thermostat control screen is highlighted, neither
Scheduled nor Triggered Smart Scenes will affect thermostat operation. However, running
Scheduled or Triggered Smart Scenes
manually
will
change thermostat settings
.
•
For
thre
shold monitoring
to be configurable on the Total Connect and Z
-Wave
thermostat screens, two
temperature
monitor
zones
must first be programmed with an
appropriate
response
type
. Consult your installer to verify that temperature monitor
zones have been programmed for your thermostats.
Note
that threshold monitoring is not available on all thermostats
.
•
Some thermostats may
not update
the
temperature
status displayed on the Controller
.
Lyric Controller Z
-Wave Thermostat Functions
Control
Function
Mode
Select between HEAT, COOL, AUTO, EMERGENCY HEAT and OFF.
Fan
Select between ON, CIRCULATE and AUTO.
The Mode and Fan settings available will vary with your thermostat.
HOLD
Neither Scheduled nor Triggered Smart Scenes can operate the selected
thermostat.
NORMAL
Allows
selected thermostat to be operated by Scheduled and Triggered
Smart Scenes.
NO SCHED
Prevents
Scheduled
Smart Scenes from operating the selected thermostat.
Threshold
Monitoring
Enable/Disable Threshold Monitoring feature
(if available)
.
Saving Off
-
Saving On
Enable/disable thermostat’s Energy Saving function.
EDIT
Used to edit
thermostat
’s name.
BACK
Return to Thermostats screen on Lyric Controller.
40
Thermostat Energy Saving Mode
1.
On the
Z-Wave
® Device Management menu,
select
Thermostats
.
2.
Select the desired thermostat from the displayed list.
3.
On the thermostat control screen,
press the
“Saving Off” button OR “Saving On”
to activate or deactivate the thermostat’s Energy Saving Schedule Function when
a heating or cooling operation is selected.
Z-Wave Compatibility
Z-Wave devices vary; follow the instruct
ions provided with the specific device when including
and excluding devices into your Z
-Wave network.
NOTE
:
Not all Z
-Wave devices have been tested. Some functions may produce unpredictable
results.
Door Locks
Appliance
Yale® Real Living Push-
Button Lever Lock
HomeManageables Appliance Module
Yale Real Living Touchscreen Lever Lock
Wayne Dalton Small Appliance Module
Yale Real Living Push-
Button Deadbolt
Lock
GE® Wireless Lighting Control Plug
-In Appliance
Module
Yale Real Living Touchscreen Deadbo
lt
Lock
Cooper In
-Wall Duplex Receptacle Module (Model
RF9505
-TDS)
Schlage® Link Deadbolt Lock
Lights
Schlage Link Lever Lock
Leviton®/ViziaRF+® Switches
Kwikset® Smartcode Lever lock
Leviton/ViziaRF+ Dimmers
Kwikset Smartcode Deadbolt Lock
Leviton/ViziaRF+ Plug
-In Appliance Modules
Thermostats
GE Wireless Lighting Control Dimmers
Honeywell Z
-Wave Thermostat (ZWSTAT)
GE Wireless Lighting Control Switches
Wayne Dalton Z
-Wave Thermostat
GE Wireless Lighting Control Plug
-In Appliance
Modules
Trane® Z
-Wave Thermostat
Intermatic In
-Wall Receptacle (Model HA01)
Residential Control Systems Thermostat
(Model TZ45)
Cooper Plug
-in Lighting Switch Module (Model
RFAPM)
Intermatic InTouch Thermostat (Model
CA8900)
AEON Labs Lamp/Dimmer Module (Model
DSC06106
-
ZWUS)
Radio Thermostat Company of America
(Model CT30, CT32, CT100, CT101)
Remotec Lamp Dimmer Module (Model ZDS
-100US)
Siren
Window Shades
FortrezZ SSA1/SSA2 Wireless Siren &
Strobe Alarm
Somfy® ILT Series
Somfy Z-
Wave to Digital Motor Interface (ZDMI)
Water Valve
FortrezZ WV-
01 Wireless Z
-Wave Water
Valve
EXISTING NETWORK NOTE:
Z- Wave products from other manufacturers can be included (added)
into the Lyric
™ network. Z
-Wave devices that are always powered can serve as repeaters regardless
of manufacturer.
USE OF THESE PRODUCTS IN COMBINATION WITH NON
-HONEYWELL PRODUCTS IN A WIRELESS MESH
NETWORK, OR TO ACCESS, MONITOR OR CONTROL DEVICES IN A WIRELESS MESH NETWORK VIA THE
INTERNET OR ANOTHER EXTERNAL WIDE AREA NETWORK, MAY REQUIRE A SEPARATE LICENSE FROM
SIP
CO, LLC. FOR MORE INFORMATION, CONTACT SIPCO, LLC OR IPCO, LLC AT 8215 ROSWELL RD., BUILDING
900, SUITE 950, ATLANTA, GA 303350, OR AT WWW.SIPCOLLC.COM
OR
WWW.INTUSIQ.COM
41
Video
Hom
e > Video
The
Controller
can display live video from as many as eight
Wi
-Fi®-connected cameras.
The Controller’s
built
-
in
camera is dedicated solely to Total Connect
® remote services. The images it
captures can be viewed only through Total Connect.
NOTE
Lyric
™ and its cameras must be on the same Wi
-Fi network.
IMPORTANT
If the Controller
loses AC power
, the Video function is disabled to minimize drain on
the backup battery.
If power is lost while you are watching Wi
-Fi
cameras on the Controller, video
display may
continue
briefly before being
suspended.
When power is restored, the Controller
looks
for available cameras
. See
Video Recovery
.
Remember that interruption of AC power to your Wi
-Fi cameras and your router
can
als
o affect the Video function, even if the Controller has AC
power.
Viewing and Naming
Cameras
1.
Press
Video
on the Home screen.
Video
appear
s in windows or the cameras appear in a
list.
OR
The
system
may
scan
for cameras
; when
the scan is complete, the
camera
list
appears.
From
the
se screens
, you can:
•
Press
to return to the Home
screen.
•
View live video.
•
Name
cameras
.
•
Add cameras to the system.
2.
Select one or more cameras
(as many as four)
in the list.
•
When multiple cameras are available, you may
select as many as four.
•
Selected
camera
s are
highlighted and the
Display
option
appears.
•
You
can
also
press
Scan
to
search
for other available cameras.
•
Press a camera’s name again to de
-select
it.
3.
Select
Display
to see
video from the
selected camera
(s).
•
Select
Camera List
to re
turn to the
list view.
•
With
multiple cameras displayed, you can select one to
work with
by tapping its
video window.
4.
Viewing a single camera displays its
details
, which vary with the camera selected.
For all compatible cameras,
you can:
•
Name the camera
. Select
Name
above the video
display
or
Edit
at right.
•
Press
Save
on the on-
screen keyboard.
•
Press
to s
how the camera full
-screen
.
•
Press
to return
to the detail view.
Some
cameras
offer additional options
such as pan/tilt and
built
-in lighting.
Adding a Camera
•
Make sure
that the camera is on the
same Wi
-
Fi network
as the Lyric system.
•
Install the camera according to its instructions.
With the camera installed:
1.
View or list
cameras
as above.
2.
Press
Scan
. The system looks for
available cameras.
3.
When the new camera is found, y
ou can name it as described above
.
42
Video R
ecovery
Home > Security >
Tools >
Wi
-
Fi
Config
If video from remote cameras is lost or becomes distorted, the system can attempt to reset video
streaming. By def
ault, Lyric
™ automatically
begins
to recover video about 60 seconds after
Wi
-Fi® communication has been restored.
The
default setting is
automatic
video recovery.
You may set
recovery
to begin only by user
intervention
(
Manual Video Recovery
).
1.
Press
Security
on
the Home screen.
2.
Select
Tools
. Enter the Master User’s security code.
3.
Press
Wi
Fi Config
.
4.
Press
Automatic Video Recovery
repeatedly to choose between automatic and manual
operation.
5.
Press
to return to the Tools menu.
43
Users and
Security Codes
Home >
Security > Tools
> Users
Lyric
™ uses 4
-digit codes to restrict certain functions to selected users. A special 4
-digit code can be
set to trigger the system’s
Duress
function.
User codes can be used interchangeably when performing sys
tem functions (a system armed with
one user's code can be disarmed by another user's code), with the exception of the Guest Code
described below.
All users are automatically assigned a
user number
, which cannot be changed.
Do not confuse these
user
numbers
with
user
codes
.
User
Code
s
Master User
This code is usually set when the system is installed, and can be
changed later. Typically, the Master User is a household member
who can perform all system functions.
Only
the Master User can add and remove users or modify their
settings. Settings include assigning security codes and user names.
Only
the Master User can create
Smart Scenes
. Access to
Smart
Scenes for other users is controlled by the Master User.
User
Typical users are household members and other authorized persons
who can arm and disarm the security system, with controlled access
to other system features.
Guest
Visitors and others who are aut
horized to arm/disarm the system
only at certain times or on a temporary basis.
The Guest’s user code can be used to
arm
the system, but cannot
disarm
it unless the system was armed using the Guest code. The
Guest’s user number is
47
.
Duress Code
IMPOR
TANT
The Duress function requires connection to an alarm monitoring service.
Household members and authorized visitors can enter this code if forced to disarm or arm the
system under threat. When the Duress code is entered, Lyric Controllers
and keypads ap
pear to
behave normally, but the system silently notifies your alarm monitoring service. The Duress
Code’s user number is
48
.
NOTES
•
A security code cannot be assigned more than once. If an existing code is entered,
the system displays the warning
User
code not accepted!
If this occurs, press
OK
to
return to user settings and assign a different code.
•
The system should be disarmed before you work with
user
codes.
•
Limited-
access users such as guests and cleaning staff should not be instructed on
syst
em functions other than those they will be using.
•
The number of user codes supported by a Z
-Wave
® door lock can vary between
manufacturers. To ensure compatibility with Lyric, set the length of the Master User
code
on the door lock to be greater than f
our digits.
44
Adding Users and Assigning Codes
1.
On the Home screen, press
Security
.
2.
Press
Tools
, and enter the Master User code.
3.
Select
Users
. Existing
Users are
displayed, along with the Guest and Duress code listings.
Four asterisks appear on each listing
that has a security code already established.
See
User Settings
for full details.
4.
Create and change settings in the menu shown here (the details may vary):
a.
Create User
: Press
Add New
and
a new user screen
like the
one pictured above appear
s.
Set the details as desired.
b.
Define/Change Guest Settings
: Press
Guest
and then
Edit
.
c.
Set/Change Duress Code
: Press
Duress
and then
Edit
. Enter a 4
-digit code.
5.
Save
after making settings. The list of user codes reappears.
6.
Pres
s
to
return to the Tools menu.
Changing Security Codes
or the Duress Code
The Master User can change other users’ names
and
security codes as well as delete users from
the system.
1.
Access the
Users
screen as shown above.
2.
Select
one of the listed users.
3.
At the bottom of the screen, press
Edit
. User details appear.
Note
that a user’s number in the
system, seen at upper right in the user details, cannot be changed.
Deleting a User
The Master user can delete secondary users from the system.
1.
Select
one of the listed users.
2.
At the bottom of the screen, press
Delete
. Lyric requests confirmation.
3.
Press
Yes
.
45
User Settings
User Name
Newly
-created users are given a default name. To cust
omize a user’s name:
1.
Press
Name
at upper left on the display. A keyboard
appears
.
2.
Press
Clear
to delete the default name.
3.
Enter the desired name, using as many as 10 characters.
4.
Press
Save
. User details appear.
5.
Press
Save
again. The list of users appear
s, displaying your changes.
User Code
Newly
-created users have no security code. To assign a code:
1.
Press
User Code
. A keypad
appears
.
2.
Press
Clear
if you are changing an existing code.
3.
Enter a four
-digit code.
4.
Press
Done
. User details appear.
5.
Press
Save
. The list of users appears.
Users and Z
-Wave Lock Control
NOTE
This option appears
only
if Z-Wave
® devices are connected.
Each user can be given
the ability to disarm the system by entering their code to open a
Z-Wave lock.
When creating or editing a User:
1.
Set
Z
-
Wave Lock Control
to
Yes
.
Z
-
Wave Unlocking Door
appears.
2.
Select
Disarm
.
3.
Press
Save
.
With this setting, entering a
user
code at any Z
-Wave
door lock in the system unlocks the
door and disarms the security system.
46
47
System Settings
Brightness/Volume
/Cleaning
Home > Settings
Adjust voice and system sounds with the Volume slider. System sounds include zone alert chimes
and countdown beeps.
Adjust
touchscreen
brightness with the Brightness slider.
NOTE
S
•
As the s
lider
s move, the Controller
previews
changing
volume and brightness levels.
•
CHIME
must be enabled
on
the
Settings
menu to enable
voice
annunciations
.
•
Volume
settings
on this menu
do
not
affect
the
Voice Command
feature.
•
Some
system event notifications can
cancel cleaning mode and return the system to
normal operation.
Press
Clean
before cleaning the touchscreen. Lyric
™ hides the controls and counts down 15
seconds. During this time, a soft, damp cloth can be used on the screen without affecting the
controls.
See
Maintenance
for more information.
Wi-Fi Configuration
Home >
Security > Tools >
Wi
-
Fi
Config
Manage your system’s r
outer here. Remember that the Controller and all Wi
-Fi® cameras must be
on the same network.
To View or Join Available Wi
-Fi Networks
1.
On the Tools menu
, press the
Wi
-
Fi Config
button. A list of Wi
-Fi options appears.
2.
Press
Scan Access Points
. A list of available networks is displayed. Use the up and
down arrows to scroll through the list. Press
to return to the previous screen.
3.
Select the desired network and press
Edit
. The network information is displayed. If a
password is required, press
Key
and enter the password.
4.
Press
Save
.
5.
Press
JOIN
.
6.
Press
to return to the previous screen.
Manually Configure Access Point
IMPORTANT
The Security setting below must match the security protocol used by your network
router.
1.
On the list of Wi
-Fi options, press
Manual Config AP
. The Wi
-Fi enrollment menu
appears. (Fields include
Network Type
, which cannot be changed.)
2.
Press
SSID Name
.
3.
Enter the network’s name.
4.
Press
Save
.
5.
Press
Security
.
48
Manual
ly
Config
ure
A
ccess
P
oint
(continued)
6.
Choose the same security protocol as your router. Options include
Open
,
wpa/wpa2
and
WPA2
. (WEP is not supported.
)
7.
If a password is required, press
Key
, and enter the password.
8.
Press
Join
. A confirmation screen appears.
9.
Press
OK
and
Save
.
10.
Pre
ss
to return to the previous screen.
Join a WPS Network
1.
On the Controller
, have the list of Wi
-Fi® options ready. Don’t press any buttons yet.
2.
Press the WPS button on the access point device or router.
3.
On the list of Wi
-Fi options, press
WPS
. The Contr
oller
displays
“Please Stand by for
WPS Operation”
.
4.
If the operation is successful, the Controller
displays
“Device has been successfully
added to the network
”.
5.
Press
OK
.
If the operation is not successful, the Controller
displays
Failed Operation. Device
not added
to the network
. Press
OK
.
Automatic/Manual Video Recovery
If video from remote cameras is lost or becomes distorted, the system can attempt to reset
video streaming. By default, Lyric
™ automatically begins to recover video about 60 seconds
after
Wi
-Fi communication has been restored.
The default setting is automatic video recovery. You may set recovery to begin only by user
intervention.
•
On the list of Wi
-Fi options, toggle between
Automatic Video Recovery
and
Manual
Video Recovery
.
•
Press
to
return to the Tools menu.
Software Updates
Home >
Security > Tools > Advanced
Lyric Controller
Software updates for the Controller are published periodically. Some
updates request user
permission in an on-
screen window. Press
Accept
,
Yes
or
OK
to instal
l the update.
Certain critical updates are installed
automatically
. After updates of this type, information
about the update is displayed on-
screen.
You can see the current version of the C
ontroller’s software at
Security > Tools > Advanced
> System
Information
.
IMPORTANT
After a new
SiX™ series sensor
or key fob
is enrolled in your system, the new
device’s software should be updated. This ensu
res that you are using the most
up-
to-date version of the software.
Sensor Firmware
Normally,
SiX
Series
sensors in your system are updated when the Controller’s software is
updated.
To initiate sensor firmware update manually:
1.
On the
Advanced
menu, press
Update Sensor Firmware
.
2.
Press
Start
and follow the instructions on the screen.
3.
Press
Stop
when
the update is complete.
4.
Press
to return to the
Advanced
menu.
49
Key F
ob Firmware
(Wireless Keys)
SiX™
Series
wireless keys:
We recommend that you have the key fob
handy
so you can work with it as instructed during
this procedure.
1.
On the
Advanced
menu, press
Update Keyfob Firmware
.
2.
Press
Start
and follow the instructions on the screen.
3.
Press
Stop
when the update is complete.
4.
Press
to return to the
Advanced
menu.
Other
types of wireless key:
Ask your installer about updating your system’s other
wireless keys
.
Slide Show
Home >
Security > Tools > Slide Show
The Controller
can dis
play your favorite photos when idle.
You can load as many as 30 images in
.jpg format
.
1.
On the Tools screen, press
and
then
Slide Show
.
2.
Connect a USB drive containing your photos (.jpg format only).
3.
Press
Load Images
.
The Controller
copies compatible files from all folders on the USB drive. When loading is
complete, photos are displayed along with slide show options
.
4.
Remove the USB drive.
5.
Select the desired options
•
Slide
Interval
: Time between slides.
•
Slide
After
: Idle time before slide show starts. Select
Disabled
for no slide show.
6.
Save
your
settings.
NOTES
•
Store up to 30 photos in the Controller,
.jpg format
only
•
The best resolution for photos in your slide show is
1024x600
; photos with different
resolutions will be modified to fit Lyric’s touch screen display.
•
Your photos’ file names should not contain spaces.
•
The slide show starts automatically when the Controller is idle.
•
To stop the slide show,
touch
the screen or the Home button.
•
To remove an image, select it on the Load menu and press
DELETE
.
Date / Time
Home >
Security > Tools > Date Time
Lyric’s
clock and calendar are normally
updated via the Controller’s network connections.
If your Controller is operating with no
network connections
, use
these controls to set date and
time manually.
Don’t forget to specify your time zone and Daylight Savings Time if necessary. Be
sure to
Save
your changes.
If Lyric
™ is reconnected to the cellular phone network or the Internet, the
clock and calendar
are
updated automatically.
50
Events
Home >
Security > Tools > Events
The Controller keeps a log
of system events such as:
•
Arm/Disarm
•
Alarm
, Trouble and Fault
•
Changes in status of Z
-Wave
® devices
The system can save up to 6000 events. When the log is full, the oldest
2000 entries are deleted
to make room for l
ogging
new event
s.
Logs
can be viewed at the Controller or export
ed
in a variety of f
ile formats.
See
Event Log Codes
for a list of logged events and how they are displayed.
Viewing Events
1.
On the Tools menu
, press
Events
. Lyric
™ list
s all
events
, sorted chronologically
.
2.
Press
All
to select different sorting options (
Alarm
,
Trouble
,
Bypass, Open or Close
or
Non
-
Security
).
3.
Select
All
on the list to return to the view of all events.
Exporting Events
NOTE
Event log export requires a USB storage device (commonly called a
thumb drive
)
formatted
with the
FAT
or
FAT32
file
system
. (You can
format a thumb drive on most
PCs and Macs.)
1.
Display events
as above and press
Export Logs
.
2.
When prompted, connect the
USB storage device.
3.
Select a file format. A
progress display
appears.
When expor
t is complete, the
previous screen appears
.
4.
Remove the storage device.
Keypad
Home >
Security > Tools > Keypad
This menu displays the MAC ID of mobile devices connected to Lyric via the
Honeywell
Controller
app.
The MAC ID
is listed
here when the app is first configured for use with Lyric.
To disconnect a device, touch its listing on the screen and press
Delete
.
The Controller
requests confirmation; press
Yes
to proceed.
51
Te s t i n g Yo u r
System
NOTE
:
TESTING SHOULD BE PERFORMED
WEEKLY.
Before testing, the
system should be disarmed and all protected doors and windows closed.
The
Home
button should show green.
No alarm messages are sent to your alarm monitoring company during these tests.
Press
Tools
and enter the 4
-digit Master User code
. Press
Advanced
.
Testing Sensors
(Walk Test)
Home > Security >
Tools > Advanced > Walk Test
Start
by
press
ing
Walk Test
.
The Controller’s internal sounder loudly
sounds and
Walk Test
–
Home to Quit
appears
. The
Control
ler
then
beeps
every 30 seconds
as a reminder that the system is in Test mode.
Note
that Walk Test mode automatically quits after 4 hours.
Doors and
Windows
Open each protected door and window in turn and listen for three beeps
from the Control
ler. If pr
ogrammed to do so,
each zone’s voice descriptor
is heard.
Identification of protection points with problems should appear
on the display. Notifications of problem zones clear when the door or
window is closed.
Motion Sensors
Walk in front of each sensor and listen for three beeps and/or voice
descriptors.
The device’s identification should appear on the display when it is
acti
vated.
The display clears when no motion is detected.
NOTE
: If wireless motion detectors are
in use, there is a 3
-minute delay
between activations, which helps preserve battery life.
Fire/Carbon
Monoxide sensors
Follow the manufacturer’s instructions to test these devices. When a
device is activated, its identification should appear on the
touchscreen
.
IMPORTANT
When testing smoke detectors
, kee
p the Lyric
™ Controller in t
est mode for
at
least one minute (60 seconds)
after
testing
the detector
to avoid sending
unwanted alarm messages to your central station monitoring company.
If there is a problem with any sensor
(no confirming sounds, no display), notify your service
company.
When all sensors have been
checked
(and
doors and windows
closed)
, no zone identification
numbers should
be displayed
.
Finish
by pressing
Home
and entering the Master User code.
52
Testing
Communications
Home > Security >
Tools > Advanced > Comm. Test
These tests check
the system’s cellular network
and
internet (Wi
-Fi®/Ethernet)
connections.
On the Advanced menu, press
Comm. Test
. The options may
vary with the devices
installed in
your system. Select the desired option to test connectivity and/or send
test
messages
to the
Central Station.
If the test is successful, Lyric
™ displays
Service OK
or
ACK Received
. Details of the test
may
be
shown.
Test
Ethernet
Checks internet connectivity without sending test messages.
Send Any
Sends test messages via all available connections.
Send Cellular Message
Sends test messages via cellular network.
Send Ethernet Message
Sends test messages via internet.
Finish
by pressing
to run a different test or by pressing
Home
. Enter the Master User code if
prompted.
Reboot
Home > Security >
Tools > Advanced > Reboot
Press
Reboot
to
restart the Controller
if required.
The system requests confirmation (“
Are You
Sure?
”). Press
Yes
to
proceed.
53
Maintenance
The Lyric
™ Controller
is designed to require little maintenance. However, testing your
system is
strongly
recommended, and regular cleaning is suggested.
•
Test the system weekly
.
•
Test your system after any
alarm occurs
.
See
Testing Your System
for more information.
Care
and Cleaning
•
Do not slam sensor
-protected doors or windows.
•
Keep dust from accumulat
ing on the touchscreen
and
sensors, particularly motion sensors
and smoke
or
carbon monoxide
detectors
.
•
The
touchscreen
and sensors should be cleaned carefully with a soft, dry cloth. Do not
clean the components with water or any other liquids.
•
We recommend cleaning the touchscreen
weekly.
Select
Settin
gs
on the
Home screen.
Press
Clean
. During
the 15 second countdown, a soft, damp cloth can be used on the screen
without affecting the controls.
NOTE
: When the security system is armed, system event notifications will cancel the cleaning
mode and return the system to normal operation. When the system is disarmed, only
certain notifications will cancel cleaning mode.
Batter
y Replacement
Home > Security > Tools > Advanced > Install Backup Battery
IMPORTANT
Replace
the battery
pack
when
the Security menu displays
Low Battery
with no
zone number specified.
Use only batteries recommended by the installer or the manufacturer.
Disarm
the system before changing the Controller’s battery pack.
Remember that you must enter the Master User code
for access to the Tools menu.
Lyric Controller
1.
Select
Advanced
on the
Tools
menu
.
2.
Select
Install Backup Battery
. Lyric
requests confirmation that you want to proceed.
3.
Press
Yes
and
leave the battery installation procedure screen open
.
4.
Open the Controller’s
case
. If wall mounted,
hang it from the self
-contained hook as
shown below.
Remove the body of the Controller from its wall mount
or
remove the desk mount from the back of the Controller.
54
Battery
Replacement
(continued)
5.
Unplug the battery
and
remove it as seen below.
6.
Install the replacement battery; remember to replace the connector inside the battery
compartment.
7.
Depending on your choice of a standard-
or high
-capacity replacement battery,
position the battery retainer clip as seen below.
8.
Close the case and replace the screw shown in Step 4.
9.
Return the Controller to its mounting location.
10.
Press
OK
on the battery i
nstallation procedure screen.
11.
The system confirms
“Battery successfully installed"
.
12.
Press
OK
. The system returns to the Adv
anced menu.
13.
Press
to return to
the previous screen(s).
55
Sensors
IMPORTANT
The
Lyric
™ Controller beeps
every 40
-45 seconds
when a sensor reports a low battery. A
sensor with a low battery will continue to operate for up to 30 days. However, the battery
must be replaced within 30 days of this audible warning beginning to sound.
Clear sensor low-
battery warnings by entering a
user code on the Controller. Follow the
sensor’s battery replacement instructions.
NOTE
For
SiX™ series
sensors and wireless keys, remove the
old
battery and wait about
10 seconds before installing the replacement battery.
Communication
Module Replac
ement
Home > Security >
Tools > Advanced >
Install
Cellular Module
Refer to the illustrations below and follow these steps to replace a communication module:
Removing the Bezel
Replacing
the Communication Module
56
Communication
Module
Replacement
(continued)
1.
With the system
not armed
, select
Tools
on the Security menu.
2.
Enter the
4- digit Master User code.
3.
Select
Advanced
.
4.
Select
Install
Cellular Module
.
Follow the on-
screen instructions for changing the module.
5.
Press
OK
on the screen
in step 4
. The system confirms installation.
6.
Press
OK
. The system returns to the Advanced menu.
7.
Reboot the Controller (see
Reboot
for details).
57
SYSTEM DISPLAY
and Buttons
Zone numbers, location and
other information may be displayed
with status indications
.
Failure and
Trouble indications
and on-
screen Panic buttons
appear in red.
Home Screen
Security
Automation
Video
Smart Scenes
Notices
Settings
Control Panel Buttons
Below Touchscreen
Panic
Press and hold for on
-screen options
Home
Press to return from other screens
On
-screen Panic Buttons
Police
Medical
Fire
Local Alarm
System Status and Security
Alarm
Bypassed Zone
Fire Alarm
Restart Timer
(more Exit time)
Automation
Failure
(Z -Wave problem)
CO Alarm
Trouble/Alert
Details on Security menu
Door Open
Arm Away
Wi
-Fi
(signal strength)
Window Open
Arm Stay
Wi
-Fi Loss
Glass Break
Arm Custom
AC Power Loss
Fire or Heat
Sensor
Arm Night Stay
Low Battery
Flood Sensor
Disarm
No Battery
58
Features
/Various
Icons may
appear in red or orange
to indicate device status.
Problems involving Z
-Wave
® devices are
indicated by the Automation icon appearing in gray on the H
ome screen.
Clean Control
Panel
Date/Time
Automation
Tools
Reminders
Switches
Users
Voice
Command
Thermostats
Events
Wi
-Fi
Config
Locks
Advanced
Slide Show
Garages
Keypad
Notices
Water
Valves
Message
59
WIRELESS KEY
S
Key Assignments
Your
wireless keys (key fobs) are set up
by your installer
. You might wish to write down each
button’s preprogrammed function
in the space
s below.
NOTES
•
One or more but
tons may have been programmed for
Panic
function.
•
To activate a button function, press and hold the button for 1-
2 seconds.
Button A:
___________________
Button B:
___________________
Button C:
___________________
Button D:
___________________
5800 Series wireless key
Button 1:
___________________
Button 2:
___________________
Button 3:
___________________
Button 4:
___________________
Button
8
*: ___________________
(press and hold BOTH buttons to activate)
SiX™ Series wireless key
SiXFOB
Wireless Key Status Indications
Press and release any key for system status.
Status is indicated by the LEDs at the top of the key fob.
Green
LED
s
Red LEDs
Sounder
System Status
Rapid Flash –
Alternating about
8-20 seconds, then ON for 3
seconds
Off
Chirp
for
confirmation
Device Enrollment
Off
ON 2
-3 seconds
2 Beeps
System Armed (any mode)
Off
Slow Flash for 2
-3
seconds
4 Beeps
Alarm in progress or
system
in Audible Panic
Mode
ON 2
-3 seconds
Off
1 Beep
Disarmed, Ready to Arm
Slow Flash for 2
-3 seconds
Off
Silent
Disarmed, Not Ready to Arm
Flash once (both LEDs)
Off
Silent
RF Transmission
Off
Off
1 Second
beep
Not Hearing from
Controller
Rapid Flash for 2
seconds
Off
Silent
Deleting
wireless
key
from
system
60
61
Event Log Codes
The Lyric
™ Controller’s Event Log can record and display as many as 6000 system events. Events
are stored locally in the Controller, in chronological order and sent to your monitoring company as
needed. When the maximum number of stored events is reached, the oldest
2000 entries are
deleted to make room for logging new events.
The type of events that can be recorded is selectable; refer to the Lyric Controller Installation and
Reference Guide’s Programmi
ng section. The Events and c
odes displayed vary with y
our syst
em’s
options. The table
below provides
definitions of the events/codes that may be transmitted to the
Central Station and/or displayed by the controller.
Note
: If the Controller’s backup battery is exhausted after AC power is lost, any system activity
occu
rring after
the
Low Battery notification
is
not
saved
. Additionally, the Controller
appears to have
the
same
status condition as it did
before the low battery notification.
Event Log Codes
Code
Definition
Event Log
Display
110
Alarm, Fire
Fire
121
Alarm, Duress
Duress
122
Alarm, Silent
Silent
123
Alarm, Audible
Audible
131
Alarm, Perimeter
Perimeter
132
Alarm, Interior
Interior
134
Alarm, Entry/Exit
Entry/Exit
135
Alarm, Day/Night
Day Night
137
Alarm,
Tamper
Tamper
145
Expansion Module Tamper
Expansion Module Tamper
146
Silent Burglary
Silent Burglary
150
24-Hour Non
-Burglary
24 Hour Non
-Burglary
162
Carbon Monoxide Detected
Carbon Monoxide Detected
301
Trouble, AC Loss
AC Loss
302
Trouble, Low System Battery
Low system battery
305
Trouble, System Reset
System Reset
308
System shutdown
System shutdown
316
System Tamper*
System Tamper
341
Trouble, Case Tamper
Cover Tamper
344
Trouble, RF Receiver Jam Detect
RF Jam Detect
350
Long Range Radio
Reset
Long Range Radio Reset
353
Trouble, Long Range Radio Transmitter Fault
Comm. Trouble
354
Failure to Communicate Event
Failure to Communicate Event
373
Trouble, Fire Trouble
Fire trouble
374
Trouble, Exit Error Alarm
Exit error alarm
380
Trouble, Sensor
Sensor trouble
381
Trouble, Loss of Supervision RF
Superv Loss
-RF
383
Trouble, Sensor Tamper
Sensor Tamper
62
Event Log Codes
Code
Definition
Event Log Display
384
RF Low Battery
RF Low Battery
385
Tro
uble, Smoke High Sensitivity
Smoke Hi Sens.
386
Trouble, Smoke Low Sensitivity
Smoke Lo Sens.
401
Open/Close by User
Arm Away/Disarmed
403
Open/Close Automatic
Automatic O/C (or Scheduled Arming)
406
Cancel
Cancel
407
Remote Arm/Disarm
Remote Arm/Disarm
408
Quick Arm
Quick arm
441
Armed Stay
Arm Stay/Disarmed
455
Auto
-Arm Failed
Auto
-arm Failed
459
Recent Close
Recent Closing
461
Wrong Code Entry
Wrong Code Entry
570
Zone/Sensor Bypass
Zone Bypass
601
Manual Trigger Test Report
Manual Trigger Test Report
602
Periodic Test Report
Periodic test report
606
Listen
-in to follow
Listen
-in to follow
607
Walk Test
Walk Test Mode
623
Event 90% Full
Event Log 90% Full
627
Program Mode Entry
Program mode entry
628
Program Mode Exit
Program mode exit
654
System Inactivity
System
Inactivity
655
Reset Master Code
User Code
759
Resident Monitor Zone Response
Resident Monitor Zone Response
760
Resident Response Zone Response
Resident Response Zone Response
761
General Monitor Zone Response
General Monitor Zone Response
762
General Response Zone Response
General Response Zone Response
1401
Local Alarm
Local Alarm
3000
Binary Switch Off
Switch Off (Z
-Wave Device)
3001
Binary Switch On
Switch On (Z
-Wave Device)
3100
Multi
-Level Switch Change Level (Off)
Multilevel Switch Off (Z
-Wave Device)
3101
Multi
-Level Switch Change Level (On)
Multilevel Switch On (Z
-Wave Device)
3200
Garage Door Close
Garage Door Close
3201
Garage Door Open
Garage Door Open
3300
Door Lock Unlocked
Door Unlocked (Z
-Wave Device)
3301
Door Lock Locked
Door Locked (Z
-Wave Device)
3302
Door Lock Jammed
Door Lock Jammed (Z
-Wave Device)
3400
Thermostat Mode Off
Thermostat Mode Off
3401
Thermostat Mode Heat
Thermostat Mode Heat
3402
Thermostat Mode Cool
Thermostat Mode Cool
3403
Thermostat Mode Auto
Thermostat Mode Auto
3404
Thermostat Mode Aux /Em Heat
Thermostat Mode Aux /Em Heat
63
Event Log Codes
Code
Definition
Event Log Display
3405
Thermostat Fan Mode Auto
Thermostat Fan Mode Auto
3406
Thermostat Fan Mode Manual On
Thermostat Fan Mode Manual On
3407
Thermostat Fan Mode Circulate
Thermostat Fan Mode Circulate
3408
Thermostat Set Heat Point
Thermostat Set Heat Point (and temperature)
3409
Thermostat Set Cool Point
Thermostat Set Cool Point (and temperature)
3410
Thermostat Hold
Thermostat Hold
3411
Thermostat No Scheduling
Thermostat No Scheduling
3412
Thermostat Normal Mode
Thermostat Normal Mode
3500
Low Battery
Low Battery (Z
-Wave Device)
3501
Low Battery Restore
Low Battery Restore (Z
-Wave Device)
4000
Voice Command Success
Displays Variable Voice Command Text
4001
Voice Command Failed
Displays Variable Voice Command Text
4002
Voice Trigger Success
Displays Variable Voice Trigger Text
4003
Voice Trigger Fail
Displays Variable Voice Trigger Text
5000
Critical Panel Firmware Update
Downloaded
Critical Panel Update Downloaded
*If your Central Monitoring station receives a “Comm. Fail” message (E316), your system has been
tampered with and may have been compromised. This occurs if no signal is heard from the alarm
panel within
15 min
utes following a delayed alarm.
64
65
Appendix: Video Doorbell
If your system is set up with a Video Doorbell, you have options to change the doorbell description
and chime tone, or delete it from the sy
stem.
If you later decide to add a video doorbell
to your
system,
see the installation
and set up instructions below.
Change
the Video Doorbell Descript
ions and Chime Sound, or
Delete a Video Doorbell
1.
Enter the Skybell Setup menu.
Home > Security > Tools >
enter Master User Code
>
(go to 2nd page)
>
SkyBell Setup
2.
A list of enrolled video doorbells appears.
3.
Select the Video Doorbell to change from the displayed list.
To Change the
Doorbell
Descript
or
a.
Select the Descriptor button and
enter the desired description.
DESCRIPTOR NOTE
: Select the desired descriptor from the built
-in Lyric
™
descriptors. The Video Doorbell cannot use Custom descriptors.
b.
Press
Save
.
To Change the Chime Sound
a.
Press
the Chime button
until
you hear the preferred Chime tone
for the doorbell
.
b.
Press
Save
.
To Delete a Video Doorbell from the Lyric Controller
a.
Press
Delete
next to
the doorbell
you want to
delete.
b.
Press
Yes
at the next prompt
and t
he
Video Doorbell
is deleted from the Lyric
Controller.
Install
a Video Doorbell
Before
adding a Video Doorbell
to your system
, contact your installer and ensure
the Video
Doorbell
option
is enabled
in the Total Connect
® Service.
System and Internet Requirements
•
Full
-time internet connection with at least 1.5mbps upload speed.
•
The Wi
-Fi® router to which the Video Doorbell is connected must operate at 2.4GHz and
support
B/G mode
. [See your
router specifications for modes supported.]
•
The
Lyric Controller firmware
must be revision
01.03.06583.482 or later
.
[For firmware revision:
Home > Security > Tools > Advanced
>
System Information
.
]
•
If the
Video Door Bell
is not already connected to your
Wi
-Fi router
, download and install the
Total Connect 2.0 mobile app on your smart device
.
NOTE
: For an alternate method of connection, refer to the instructions that came with
the
video doorbell.
Installation
process:
•
Install the doorbell
•
Connect the Video Doorbell to the Wi
-Fi Network
•
Configure the Video Doorbel
l for use with the Lyric Controller
•
Add the Video Doorbell to the Lyric Controller
(
continued on the next page
66
Video Doorbell
Installation
1.
Install
the Video Doorbell according to its instructions.
2.
Connect
the Video Doorbell to your
Wi
-Fi® network.
[If it is already connected, skip to step 3.]
a. Put the doorbell into hotspot mode
by
press
ing
and hold
ing
the doorbell button until it
blinks alternating red and green.
b. Start the Total Connect
® 2.0 mobile app and select the Doorbell (Skybell) menu. Press
SETUP SKYBELL
, then press
NEXT
.
c. Select the V
ideo
Doorbell from the displayed list of devices to connect the device to the
Video Doorbell hotspot
and press
NEXT
.
d. Select
your
Wi
-Fi router from the displayed list of devices to connect the Video Doorbell
to
your
Wi
-Fi network. Press
NEXT
. Enter the router’s password if required, then press
NEXT
.
e. A popup message appears: “Your SkyBell front door has been added to Total Connect.”
Press
OK
. The Video Doorbell is now ready to be configured for use with the Lyric
™
Controller.
NOTE
: The Wi
-Fi sync process may require more than one attempt to connect. If needed,
use the
Try Again
button to reattempt.
3.
Configure
the Video Doorbell for use with the Lyric Controller.
a. Using the smart device browser (or PC with IE 10.0 or higher), go t
o:
https://hwinstall.myskybell.com/
b. Enter access code:
honeywelllyriccontroller
c. Enter
the
Video Doorbell serial number: __________________________
(the
serial number
is located on the label on the back of the doorbell)
d. Select
Configure
.
The screen displays “Success! The SkyBell has successfully been updated with the Lyric
Panel configuration.”
e.
Exit the website. The doorbell is now ready to be added to the Lyric Controller.
4.
Add
the Video Doorbell to the Lyric Controller.
a. From the Lyric Controller touchscreen, select the SkyBell Setup option:
Home > Security > Tools >
enter
Master
User Code
>
(go to 2nd page)
>
Sky
B
ell Setup
b. The Controller displays, “To enroll a Doorbell, press a button on that Doorbell.” Go to the
doorbell and press its button.
c. Press “Please select a description for doorbell” to assign the desired descriptor and to
select the desired chime sound played at the controller when the doorbell is pressed.
Press
Save
.
DESCRIPTOR NOTE
: Select the desired descriptor from the built
-in Ly
ric descriptors. The
Video Doorbell cannot use Custom descriptors.
d. The door bell name and serial number appear on the Lyric screen. The
Video Doorbell is
now ready to be used.
NOTE
: If the message “Please select a description for doorbell” does not appear, repeat
steps
3 and
4.
67
Glossary
Arm Away
Enables all exterior and interior security protection provided by door and window
sensors and motion detectors.
Arm
Custom
Allows
authorized users to arm the system with selected zones bypassed or with
entry delays disabled.
Arm Stay
Enables exterior protection; sounds an alarm if protected doors or windows are
disturbed. Allows bypassing of selected zones, permitting movement withi
n the
home without unwanted alarms.
Bypass
Allows authorized users to exclude selected protection zones when arming the
system.
Disarm
Turns off the security portion of the system. Silences alarms and trouble indicators.
Duress
Special code that can
be entered into the system instead of a normal user code.
Sends a silent call
for assistance
while the Controller
appears to behave normally.
Requires connection to a central monitoring service.
Panic
Special keys on the controller activate sounders on the premises and optionally
send alert messages in various types of emergency. Connection to a central
monitoring service is required for outside emergency calls.
Quick Arm
Allows household members to arm the system without entering a user code. This
featur
e can only be enabled by an authorized user.
Quick Exit
Allows an outside door to be opened for a set time period. This feature is used for
checking the mailbox, retrieving the newspaper, etc.
Zone
Specific areas of protection in your home. Sensing devic
es are assigned to these
numbered Zones, with designations such as front door, kitchen window, etc. Zone
numbers appear on the display when an alarm or fault occurs.
Z
-
Wave
®
Controller
The
primary
controller is the main device used to set up and control the Z
-Wave
network. There can only be one primary controller and it must be used to
add/Include or delete/Exclude devices. A primary controller can be a portable
device such as a hand-
held remote,
a permanently mounted control panel, a
Z-
Wave
enabled PC or a Z
-Wave enabled Ethernet router/bridge.
A
secondary
controller cannot be used to add or delete devices. If the secondary
controller is the same model as the primary, it will have all of the prim
ary’s
capabilities, but cannot be used to add or delete devices.
Exclude
When a device is Excluded, it is removed from the system. Excluding the device
also removes the network pairing from the device’s memory. In this document, the
term Exclude is used interchangeably with “Delete”.
Include
Including a device pairs it with the Controller
so the two can communicate. In this
document, the term Include is used interchangeably with “Add”.
Important Note: A device must be
Excluded
before it can be moved to another network or re
-
Included after a controller reset.
68
69
Fire/CO Alarm System
Your fire alarm system (if installed) is active 24 hours a day, providing continuous protection. In the
event of an emergency, the installed smoke, heat and/or carbon monoxide detectors will
automatically activate your security system, triggering a loud, i
ntermittent tone from the Lyric
™
Controller
. The sound alternates with the voice announcement, sounding every 15 seconds. A “FIRE”
or “CO” message appear
s on the
touchscreen
and remain until you silence
the alarm and clear the
display.
In Case of Fire
1.
Should you become aware of a fire emergency before your detectors sense the problem,
go to the Controller
and press and hold the Panic
button and then select the Fire icon.
The alarm will sound and an alarm will be transmitted to the central station.
2.
Evacuate
all occupants from the premises.
3.
If flames and/or smoke are present, leave the premises and notify your local Fire
Department immediately.
4.
If no flames or smoke are apparent, investigate the cause of the alarm. The zone number
of the zone(s) in an alarm c
ondition will appear on the
touchscreen.
In Case of Carbon Monoxide Alarm
1.
If a high level of carbon monoxide is detected you should evacuate all occupants from the
premises and immediately move to a location where fresh air is available, preferably
outdoo
rs.
2.
From a safe area, contact your central monitoring company for further instructions.
Silencing a Fire/Carbon Monoxide Alarm
NOTE
: Fire and Carbon Monoxide alarms CANNOT be cleared via remote services such as
Total Connect
®. For your safety, alarms of this type can ONLY be cleared from the
keypad on the Lyric Controller itself.
1.
Silence the alarm by entering
the Master User code.
2.
To clear the alarm, enter the Master User code again.
3.
If the touchscreen
indicates a trouble condition after entering the Mast
er User code a
second time
, check that smoke detectors are not responding to smoke-
or heat
-producing
objects in their vicinity. Should this be the case, eliminate the source of heat or smoke.
4.
If this does not remedy the problem, there may still be smoke in the detector. Clear it by
fanning the detector for about 30 seconds.
5.
When the problem has been corrected, clear the display by entering Master User code
again.
70
71
National Fire Protection Association
Smoke Detector Recommendations
With regard to the number and placement of smoke and heat detectors, we subscribe to the
recommendations contained in the National Fire Protection Association's (NFPA) Standard #72
noted below.
Early warning fire detection is best achieved by the installation of fire detection equipment in all
rooms and areas of the household. The equipment should be installed as follows: A smoke detector
installed outside of each separate sleeping area, in the immediate vicinity of the bedrooms and on
each additional story of the family living unit, including basements and excluding crawl spaces and
unfinished attics.
In addition, the NFPA recommends that you install heat or smoke detectors in the living room, dining
room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and stor
age rooms, basements and
attached garages.
72
Emergency Evacuation
Establish and regularly practice a plan of escape in the event of fire. The following steps are
recommended by the National Fire Protection Association:
1.
Position your detector or your interior and/or exterior
sounders so that they can be heard by all occupants.
2.
Determine two means of escape from each room. One
path of escape should lead to the door that permits
normal exit from the building. The other should be an
alternative escape, such as a window, should y
our path
to that door be impassable. Station an escape ladder
at such windows if there is a long drop to the ground.
3.
Sketch a floor plan of the building. Show windows,
doors, stairs and rooftops that can be used to escape.
Indicate escape routes for each r
oom. Keep these
routes free from obstruction and post copies of the
escape routes in every room.
4.
Assure that all bedroom doors are shut while you are
asleep. This will prevent deadly smoke from entering
while you escape.
5.
Try the door. If the door is hot, c
heck your alternate
escape route. If the door is cool, open it cautiously. Be
prepared to slam the door if smoke or heat rushes in.
6.
When smoke is present, crawl on the ground. Do not
walk upright, since smoke rises and may overcome
you. Clearer air is near
the floor.
7.
Escape quickly; don't panic.
8.
Establish a place outdoors, away from your house,
where everyone can meet and then take steps to
contact the authorities and ac
count for those missing.
Choose someone
to assure that nobody returns to the
house
— many die going back.
73
Regulatory Agency Statements
FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC)
STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized
by the Installation Instructions or User's Manual. Unauthorized changes or modifications
could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for
use. The FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used
properly, that is, in strict accordance with the manufacturer's instructions, may cause
interference to radio and television reception. It has been type tested and found to comply
with the limits for a Class B computing device in accordance with the specifications in Part
15 of FCC Rules, which are designed to provide reasonable protection against such
interference in a residentia
l installation. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the r
adio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television
receiver are on different bra
nch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA CLASS B STATEMENT
Cet appareil numérique de la classe B est conforme à la norme NMB
-003 du Canada.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and Industry Canada’s license-
exempt
RSSs
. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference receiv
ed, including
interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FC
C et exempt de licence RSS
d’Industrie Canada
. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil
ne doit pas c
auser d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence
reçue y compris les interférences causant une réception indésirable.
RF EXPOSURE WARNING
The antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 7.8 inches
(20 cm) from all persons and must not
be co
-
located or operated in conjunction with any other transmitter except in
accordance with FCC and ISED
multi
-transmitter product procedures.
MISE EN GARDE
Exposition aux Fr
é
quences
Radio:
La/les antenne(s) utilisée(s) pour cet
émetteur doit/doivent être installée(s) à une distance de séparation d'au moins 20
cm (7,8 pouces) de toute personne et ne pas être située(s) ni fonctionner
parallèlement à tout autre transmetteur ou antenne, excepté en conformité avec
les procédures de produit multi transmetteur FCC et ISED.
Continued next page
74
IMPORTANT NOTE ABOUT EXTERNAL ANTENNAS
If an external cellular radio antenna is used, the antenna may be installed or replaced ONLY
by a
professional installer.
TO THE INSTALLER
Lyric
™
-
3G, Lyric
-
3GC
The external antenna must not exceed a maximum directional gain (including cable loss) of
6.0 dBi at 850 MHz and 2.5 dBi at 1900 MHz. Under no conditions may an antenna gain be
used that would exceed the ERP and EIRP power limits as specified in FCC Parts 22H and
24E and 27, and IC RSS-
130, RSS-
132, RSS-
133, and RSS-
139.
Lyric
-
CDMA
The external antenna must not exceed a maximum directional gain (including cable loss) of
9.3 dBi at 850 MHz and 8
.2 dBi at 1900 MHz. Under no conditions may an antenna gain be
used that would exceed the ERP and EIRP power limits as specified in FCC Parts 22H and
24E and 27.
LYRICLTE
-
A, LYRICLTE
-
C
This device is to be used in mobile or fixed applications only. For mo
bile and fixed
operating configurations the antenna gain, including cable loss, must not exceed 3.25 dBi
(US) or 0.6dBi (Canada) at 850 MHz, 5.5 dBi at 1700 MHz, 2.5dBi at 1900 MHz for satisfying
RF exposure compliance. Under no conditions may an antenna gain be used that would
exceed the ERP and EIRP power limits as specified in Part 22H and 24E and 27, and IC RSS-
130, RSS-
132, RSS-
133, and RSS-
139.
LYRICLTE
-
V
This device is to be used in mobile or fixed applications only. For mobile and fixed
operating
configurations the antenna gain, including cable loss, must not exceed 7.31 dBi at
780 MHz, 7.35 dBi at 1700 MHz for satisfying RF exposure compliance. Under no conditions
may an antenna gain be used that would exceed the ERP and EIRP power limits as
speci
fied in Part 22H and 24E and 27.
75
OWNER'S INSURANCE PREMIUM CREDIT REQUEST
This form should be completed and forwarded to your homeowner's insurance carrier for possible premium credit.
A. GENERAL INFORMATION:
Insured's Name and Address:
Insurance Company:
Policy No.:
Lyric
™
Controller
_______________________
Other
Type of Alarm:
Burglary
Fire
Both
Installed by:
Serviced by:
Name
Name
Address
Address
B. NOTIFIES (Insert B = Burglary, F = Fire)
Local Sounding Device
Police Dept.
Fire Dept.
Central Station
Name:
________________________________________________________________
_________
Address:
Phone:
C. POWERED BY:
A.C. with Rechargeable Power Supply
D. TESTING:
Quarterly
Monthly
Weekly
Other
E. SMOKE DETECTOR LOCATIONS
Furnace Room
Kitchen
Bedrooms
Attic
Basement
Living Room
Dining Room
Hall
F. B
URGLARY DETECTING DEVICE LOCATIONS:
Front Door
Basement Door
Rear Door
All Exterior Doors
1st Floor Windows
All Windows
Interior
Locations
All Accessible Openings, Including Skylights, Air Conditioners and Vents
G. ADDITIONAL PERTINENT INFORMATION:
Signature:
Date:
76
77
Your System Information
Your local Honeywell dealer is the person best
qualified to service your alarm system.
Arranging a program of regular service is advisable.
Security Company/Installer:
Name:
Phone:
Address:
DELAY DURATIONS, ARMING OPTIONS AND EMERGENCY TYPES
Exit Delay
time
___________
Entry Delay
1 time
_________
Entry Delay
2 time
_________
ARM NIGHT enabled
Yes
No
Zones
________________________________________
AUTO HOME enabled
Yes
No
Restart Exit Delay enabled
Yes
No
QUICK ARM enabled
Yes
No
QUICK EXIT enabled
Yes
No
CHIME
mode enabled
Yes
No
Audio Alarm Verification enabled
Yes
No
(Two
-Way Voice)
FIRE
Yes
No
MEDICAL
Yes
No
POLICE
Yes
No
Silent
Alarm Reporting Delay
__________
SYSTEM USERS
Keep track of authorized system users in the chart below. This record should be kept secure by the
Master User.
User #
User Code
Comment/Description
02
(preset)
Master User
Can add and modify Users.
Can add, modify, edit and run all Smart Scenes.
47
(preset)
Guest
The Guest user code can be used to arm the system, but
cannot disarm it unless the system was armed using the Guest
code.
48
(preset)
Duress
Enter this code if forced to disarm/arm the system under
threat. System appears to behave norma
lly, but silently notifies
alarm monitoring service.
03
04
05
06
07
08
09
10
11
12
13
14
78
ZO
NES
Zon
e
Number
Location and
Description
79
SMART SCENES
Smart Scene
Name
Description
Z
-
WAVE
®
DEVICES
Type
Name
Location
80
-
Notes
–
81
-
Notes
-
82
Limitations of This Alarm System
WARNING!
While this system is an advanced design security system, it does not offer guaranteed protection against
burglary or fire or other emergency. Any alarm system, whether commercial or residential, is subject to
compr
omise or failure to warn for a variety of reasons. For example:
•
Intruders may gain access through unprotected openings or have the technical sophistication to bypass an
alarm sensor or disconnect an alarm warning device.
•
Intrusion detectors (e.g. passive i
nfrared detectors), smoke detectors, and many other sensing devices
will
not work without power. Battery operated devices will not work without batteries, with dead batteries, or if
the batteries are not put in prope
rly. Devices powered solely by AC will not work if their AC power supply is
cut off for any reason, however briefly.
•
Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm
receiver. Even if the signal path ha
s been recently checked during a weekly test, blockage can occur if a
metal object is moved into the path.
•
A user may not be able to reach a panic or emergency button quickly enough.
•
While smoke detectors
have played a key role in r
educing residential fire deaths in the United States, they
may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to
data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used
in conjunction with this System may not work are as follows. Smoke detectors may have been improperly
installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the
detectors, such as in chimneys, in wa
lls, or roofs, or on the other side of closed doors. Smoke detectors also
may not sense a fire on another level of a residence or building. A second floor detector, for example, may
not sense a first floor or basement fire. Moreover, smoke detectors have s
ensing limitations. No smoke
detector can sense every kind of fire every time. In general, detectors may not always warn about fires
caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper
storage of flamma
ble materials, overloaded electrical circuits, children playing with matches, or arson.
Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it
operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to
prevent injury or death.
•
Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in
their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do
create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by
those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed
doors, glass parti
tions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any
material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive
Infrared Detectors sense changes in temperature; howev
er, as the ambient temperature of protected area
approaches the temperature range of 90° to 105°F, the detection performance can decrease.
•
Alarm warning devices
such as sirens, bells or horns may not alert people or wake up sleepers if they
are
located on the other side of closed or partly open doors. If warning devices sound on a different level of the
residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even
persons who are awake may not hear
the warning if the alarm is muffled from a stereo, radio, air conditioner
or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn
hearing
-impaired people or waken deep sleepers.
•
Communication paths needed to t
ransmit alarm signals from a premises to a central monitoring station
may
be out of service or temporarily out of service. Communication paths are also subject to compromise by
sophisticated intruders.
•
Even if the system
responds to the emergency as intended, however, occupants may have insufficient time
to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities
may not respond appropriately.
•
This equipment, like other electric
al devices
, is subject to component failure. Even though this equipment is
designed to last as long as 10 years, the electronic components could fail at any time.
The most common cause of an alarm system not functioning when an intrusion or
fire occurs is inadequate
maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working
properly.
Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a
subst
itute for insurance. Homeowners, property owners and renters should continue to act prudently in
protecting themselves and continue to insure their lives and property.
We continue to develop new and improved protection devices
. Users of alarm systems owe it to themselves and
their loved ones to learn about these developments.
83
TWO YEAR LIMITED WARRANTY
Honeywell International Inc., acting solely through its Security & Fire
business (“Seller”), 2 Corporate Center
Drive, Melville, New York 11747 warrants its products to be free from defects in materials and workmanship
under normal use and service, normal wear and tear excepted, for 24 months from the manufacture date code;
provided, however, that in the event the Buyer presents a proper inv
oice relating to the purchased product and
such invoice bears a date later than the manufacture date, then Seller may at its discretion, reflect the warranty
period as commencing at invoice date. Except as required by law, this Limited Warranty is only mad
e to Buyer
and may not be transferred to any third party. During the applicable warranty period, Seller will repair or
replace, at its sole option and as the exclusive remedy hereunder, free of charge, any defective products.
Seller shall have no obligatio
n under this Limited Warranty or otherwise if the product:
(i) is improperly installed, applied or maintained;
(ii)
installed outside of stated operating parameters, altered or improperly serviced or repaired by anyone other
than the Seller/Seller’s Authorized Service/Repair Center;
(iii)
damage is caused by outside natural occurrences, such as lightning, power surges, fire, floods, acts of
nature, or the like; or
(iv)
defects result from unauthorized modification, misuse, vandalism, alterations of se
rial numbers, other causes
unrelated to defective materials or workmanship, or failures related to batteries of any type used in
connection with the products sold hereunder.
Exceptions to Warranty With Respect to Honeywell Products listed below:
Hardwire C
ontacts and PIRs –
Seller warrants parts for hardwire contacts and PIRs in accordance with the terms
of the above limited warranty for a period of five (5) years from the manufacture date code.
EXCLUSION OF WARRANTIES, LIMITATION OF LIABILITY
THERE ARE NO WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS
FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. TO THE FULLEST EXTENT PERMITTED BY LAW, IN NO CASE SHALL SELLER BE LIABLE TO
ANYONE FOR ANY (i) CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES ARISING
OUT OF OR RELATING IN ANY WAY TO THE PRODUCT AND/OR FOR BREACH OF THIS OR ANY OTHER
WARRANTY OR CONDITION, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY
WHATSO
EVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY SELLER’S OWN NEGLIGENCE OR FAULT AND
EVEN IF SELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES OR DAMAGES. Any product
description (whether in writing or made orally by Seller or Seller’s agents), speci
fications, samples, models,
bulletin, drawings, diagrams, engineering sheets or similar materials used in connection with the Buyer’s order
are for the sole purpose of identifying the Seller’s products and shall not be construed as an express warranty or
condition. Any suggestions by Seller or Seller’s agents regarding use, applications, or suitability of the products
shall not be construed as an express warranty or condition unless confirmed to be such in writing by Seller.
Seller does not represent that t
he products it sells may not be compromised or circumvented; that the products
will prevent any personal injury or property loss by burglary, robbery, fire or otherwise, or that the products will
in all cases provide adequate warning or protection. Buyer u
nderstands that a properly installed and maintained
alarm may only reduce the risk of a burglary, robbery or fire without warning, but it is not insurance or a
guarantee that such will not occur or will not cause or lead to personal injury or property loss
. CONSEQUENTLY,
SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS
BASED ON ANY CLAIM AT ALL INCLUDING A CLAIM THE PRODUCT FAILED TO GIVE WARNING. However, if
Seller is held liable whether directly or indirectly for any loss or damage with respect to the products it sells,
regardless of cause or origin, its maximum liability shall not in any case exceed the purchase price of the
product, which shall be fixed as liquidated damages and not as a penalty, and shall be the comp
lete and
exclusive remedy against the Seller. Should your product become defective during the warranty, please contact
your installer to facilitate repair or replacement with Seller pursuant to the terms hereof. Seller reserves the right
to replace any def
ective product under warranty with new, refurbished, or remanufactured product.
For patent information, see
www.honeywell.com/patents
Honeywell is a registered trademark of Honeywell International Inc.
All other trademarks are the property of their respective owners.
All rights reserved
Ref:
LCP500
-L/LCP500-
LC
Ê800-18078jŠ
800-
18078 11/15 Rev. F
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
2015 Honeywell International Inc.
www.honeywell.com/security
- Uploaded