Resideo Z5DIMMER Z-Wave Plus In-Wall Smart Dimmer - Install Guide

NOTE:
Actual performance of any CFL or LED will vary from bulb type to bulb type and among
different manufacturers. It is important to note only bulbs designed as dimmable should be used
with a dimmer. To find out if your bulb is dimmable, please check the package, the bulb itself or call
the a bulb manufacturer directly.
For a complete list of recommended CFL/LED bulbs for this and other Z-Wave products from
Honeywell Home, please visit www.security.honeywellhome.com.
MULTI-SWITCH WIRING
The Honeywell Home Add-on Switch is required for multi-switch 3-way or 4-way
installations. Connecting the traveler terminal of this switch to a standard, non-
Honeywell Home switch will cause damage or result in improper function. If this
switch is a part of a 3-way or 4-way multi-switch installation, do not connect the
traveler wire or apply power until Honeywell Home Add-on Switches are correctly
installed. For more information on 3-way or 4-way installations, view the manual
or quick-start guide with the Honeywell Home Add-on Switch.
SINGLE-SWITCH WIRING
Before installation, you may wish to change the paddle color to match your
wallplate or decor. Please proceed to
section 5
1.
Shut off power to the circuit at circuit breaker or fuse box.
IMPORTANT!
Verify power is OFF to switch box before continuing.
2.
Remove wallplate.
3.
Remove the switch mounting screws.
4.
Carefully remove the switch from the switch box. DO NOT disconnect
the wires.
5.
There are up to five screw terminals on the dimmer; these are marked:
A.
GROUND — Green/Bare
B.
LOAD — Black (connected to lighting)
C.
LINE (Hot) — Black (connected to power)
D.

TRAVELER — Red/Other (only in 3-way installations)
E.
NEUTRAL — White
Match these screw terminals to the wires connected to the
existing switch.
6.
Disconnect the wires from the existing switch. Label wires according to
the previous terminal connection.
OBSERVE IMPORTANT WIRING INFORMATION
IMPORTANT
!
This dimmer is rated for and intended to only be used with copper wire.
WIRE GAUGE REQUIREMENTS
Use 14 AWG or larger wires suitable for at least 80° C for supplying line (hot),
load, neutral, ground and traveler connections.
WIRE STRIP LENGTH
7.
For attachment to screw terminals,
strip insulation 1in. (25mm).


For attachment using the enclosure’s holes,
strip insulation 5/8in. (16mm).
UL specifies that the tightening torque for the screws is
14 Kgf-cm (12 lbf-in).
8.
Connect the green or bare copper ground wire to the GROUND
terminal.
9.
Connect the black wire from the light to the LOAD terminal.
10.
Connect the black wire from the electrical service panel (hot) to the
LINE terminal.
11.
Connect the white wire to the NEUTRAL terminal (use a jumper wire if needed).
Note:
The traveler terminal is only used for 3-way or 4-way wiring and
should remain insulated if the switch is being installed in a single-pole
installation (one switch & one load).
12.
Insert dimmer into the switch box being careful not to pinch or crush wires.
13.
Secure the dimmer to the box using the supplied screws.
14.
Mount the wallplate.
15.
Reapply power to the circuit at fuse box or circuit breaker and test


the system.
BASIC OPERATION
The connected light can be turned ON/OFF in two ways:
1.
Manually from the front panel of the in-wall dimmer.
2.

Remotely with a Z-Wave controller.
MANUAL CONTROL
The front panel rocker switch allows the user to turn ON/OFF the
connected fixture.
•
To turn the connected fixture ON:
Press and release the top of the rocker.
•
To turn the connected fixture OFF:
Press and release the bottom of
the rocker.
ADJUST DIM LEVELS
1.

To increase brightness
: Press and hold the top of the rocker.
2.
T
o decrease brightness
: Press and hold the bottom of the rocker.
DISABLE/ENABLE LED
1.
Press
up 3 times then quickly press and release down 1 time.
2.
Repeat to disable/enable LED.
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the switch and lighting fixture at the service
panel. All wiring connections must be made with the POWER OFF to avoid personal injury
and/or damage to the switch. This device is intended for installation in accordance with the
National Electric Code and local regulations in the United States or the Canadian Electrical
Code and local regulations in Canada. If you are unsure or uncomfortable about performing
this installation, consult a qualified electrician.
SINGLE-, DUAL- AND TRIPLE-GANG BOXES
When installing the In-Wall Smart Dimmer in multiple-gang boxes, it may be
necessary to break off one or both sides of the scored tabs on the front yoke.
This will affect the electrical rating of the dimmer (see specifications
for details).
FCC / IC - EN
A.
Ground
(Green/Bare)
B.
Load
(Black)
C.
Line
(Black)
D.

Traveler
(Red/Other)
E.
Neutral
(White)
F.
Top rocker
—
Press & release to
turn dimmer on, press & hold to
increase brightness
G.
Bottom

rocker
—
Press &
release to turn dimmer off, press
& hold to dim
B
E
C
A
D
IMPORTANT!
The fixture controlled by the Z-Wave In-Wall Smart Dimmer must not exceed 600W
(incandescent); 150W dimmable CFL/LED. The dimmer is designed only for use with
permanently installed fixtures.
•
Turn ON/OFF and adjust dim levels manually or remotely via the
Z-Wave controller
•
Can be added in multiple groups and scenes
•
May be used in single-pole installation or with up to two Honeywell Home
Add-on Switches in 3-way or 4-way wiring configurations
•
Compatible with all incandescent and most dimmable CFL/LED bulbs
•
Interchangeable paddle switch — white & light almond paddle in package
•
Uses a standard, decorative-style wallplate for single-gang installations
(wallplate not included)
•
Blue LED indicates switch location in a dark room
•
Z-Wave certified for simple pairing and integrated home automation
•
Screw terminal installation — requires wiring connections for line (hot),
load, neutral and ground. Traveler wire required for 3-way or
4-way installation
FEATURES
2
TOOLS
INSTALLATION
1
3
1.
2.
CONNECTING YOUR DEVICE TO A Z-WAVE NETWORK
1.
Follow the instructions for your Z-Wave certified controller to add
a device to the Z-Wave network.
2.
Once the controller is ready to add your device, press and release the
top or bottom of the smart dimmer (rocker). Repeat as necessary to
add the dimmer to the network.
Now you have complete control to turn your fixture ON/OFF

according to groups, scenes, schedules and interactive automations
programmed by your controller.
If your Z-Wave certified controller features remote access, you can control
your fixture from your mobile devices.
REMOVING AND RESETTING THE DEVICE
1.
Follow the instructions for your Z-Wave certified controller to remove a
device from the Z-Wave network.
2.
Once the controller is ready to remove your device, press and release
the top or bottom of the smart dimmer (rocker) to remove it from

the network.
RETURNING DIMMER TO FACTORY DEFAULTS
Quickly press ON (top) button 3 times then immediately press the OFF
(bottom) button 3 times. The LED will flash ON/OFF 5 times when
completed successfully.
Note:
This should only be used in the event your network’s primary controller is missing
or otherwise inoperable.
CHANGING PADDLE COLOR
This step is optional. Before installation, you may want to change the color of
the paddle to match your wallplate or decor.
1.
Lift the air gap tab at the base of the paddle.
2.
Push side tabs in on one side and then the other to release paddle. Lift
the cover up and off.
3.
Simply put the new paddle onto the switch by inserting the air gap and
side tabs and snapping securely into place.

Once this step has been completed please return to section 3.
5
CONNECTION
CUSTOMIZATION
4
This device supports Association Command Class (3 Groups)
•
Association Group 1 supports Lifeline, Multilevel Switch Report
•
Association Group 2 supports Basic Set and is controlled by pressing
the ON or OFF button with the local load
•
Association Group 3 supports Basic Set and is controlled by double
pressing the ON or OFF button
•
Each Association Group supports 5 total nodes
12
13
C
E
B
D
A
OUT TO LIGHT
(LOAD)
FROM BREAKER BOX
8
14
OUT

TO

LIGHT

(
LOAD
)
FROM

BREAKER

BOX
B
D
A
E
C
1
1
2
5
6
3
4
7
F
G
SMART DIMMER
IN-WALL
INTERRUPTOR
DE PARED

REDUCTOR
DE


LUZ INTELIGENTE
INTELLIGENT GRADATEUR
MONTAGE MURAL
9
10
11
MADE IN CHINA/FABRIQUÉ EN CHINE/HECHO EN CHINA
39458 | ZW3005 | 04/05/19 v3
All brand names shown are
trademarks of their respective owners.
Tous les noms de marque illustrés
sont des marques de commerce
de leurs propriétaires respectifs.
odos los nombres de marca
que aparecen son marcas
comerciales pertenecientes a
sus respectivos propietarios.
FCC / IC - EN
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS
standards. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC NOTE:
The manufacturer is not responsible for any radio or TV interference caused

by unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
—
Reorient or relocate the receiving antenna.
—
Increase the separation between the equipment and receiver.
—
Connect the equipment into an outlet on a circuit different to which the receiver is connected.
—
Consult the dealer or an experienced radio/TV technician for help.
Important note:
To comply with the FCC RF exposure compliance requirements, no change to
the antenna or the device is permitted. Any change to the antenna or the device could result
in the device exceeding the RF exposure requirements and void user’s authority to operate
the device.
FCC /IC - FR
Cet appareil est conforme au paragraphe 15 des normes FCC et au CNR pour les appareils
exempts de licence d’Industrie Canada. Son utilisation est sujette aux deux conditions
suivantes (1) cet appareil ne doit pas occasionner de brouillage préjudiciable et (2) cet
appareil doit accepter toutes les interférences reçues, notamment les interférences qui
peuvent provoquer un fonctionnement non désiré.
REMARQUE DE LA FCC :
Le fabricant n’est pas responsable des interférences sur les
fréquences radioélectriques ou télévisuelles pouvant être causées par des modifications non
autorisées de ce matériel. De telles modifications peuvent annuler le droit de l’utilisateur à
utiliser cet appareil.
REMARQUE :
Cet appareil a été testé et certifié conforme aux limites relatives aux appareils
numériques de catégorie B définies dans le paragraphe 15 des normes FCC. Ces limites ont
été définies afin de fournir une protection raisonnable contre le brouillage préjudiciable en
milieu résidentiel. Cet appareil produit, utilise et peut émettre des ondes de fréquence radio et,
s’il n’est pas installé et utilisé conformément aux instructions, il peut provoquer un brouillage
préjudiciable aux communications radio. Il n’existe toutefois aucune garantie que des
interférences ne se produiront pas dans une installation donnée. Si cet appareil occasionne
un brouillage préjudiciable à la réception radiophonique ou télévisuelle, il suffit d’allumer
et d’éteindre l’appareil pour déterminer sa responsabilité. Nous encourageons l’utilisateur à
essayer de corriger ces interférences en appliquant une ou plusieurs des mesures suivantes :
—
Réorienter ou déplacer l’antenne de réception.
—
Augmenter la distance entre l’appareil et le récepteur.
—
Brancher l’appareil à une prise secteur différente de celle du récepteur.
—
Pour obtenir de l’aide, consulter le revendeur ou un technicien spécialisé en postes radio
ou téléviseurs.
Remarque importante :
Pour se conformer aux exigences de conformité de la FCC concernant
l’exposition aux RF, aucune modification apportée à l’antenne ou au dispositif n’est autorisée.
Toute modification apportée à l’antenne ou au dispositif pourrait faire en sorte que le
dispositif dépasse les exigences d’exposition aux RF et pourrait annuler le droit de l’utilisateur
à utiliser ce dispositif.
FCC /IC - ES
Este dispositivo cumple con las especificaciones del apartado 15 de las normas de la FCC
y con las especificaciones de las normas radioeléctricas (RSS) del Ministerio de Industria
de Canadá aplicables a aparatos exentos de licencia. El funcionamiento está sujeto a las
siguientes dos condiciones: (1) este dispositivo no debe provocar interferencia perjudicial, y
(2) este dispositivo debe aceptar toda interferencia que reciba, incluso la que pudiera causar
un funcionamiento no deseado.
NOTA DE LA FCC:
El fabricante no se hace responsable de ninguna interferencia de
radio o TV ocasionada por modificaciones no autorizadas efectuadas a este equipo. Estas
modificaciones podrían anular la autoridad del usuario para utilizar este equipo.
NOTA:
Este equipo ha sido probado y cumple con los límites para dispositivos digitales
de Clase B, de conformidad con el apartado 15 de la normativa de la FCC. Estos límites
están diseñados para proveer protección razonable contra interferencias perjudiciales
en instalaciones residenciales. Este equipo genera, usa y puede irradiar energía de
radiofrecuencias y, si no se instala y usa según las instrucciones, puede provocar interferencia
perjudicial a las radiocomunicaciones. No obstante, no hay garantías de que no ocurrirá
interferencia en una instalación en particular. Si este equipo provoca interferencia perjudicial
a la recepción de radio o televisión, lo que puede determinarse encendiendo y apagándolo,
se recomienda que el usuario intente corregir la interferencia aplicando una o más de las
siguientes medidas:
—
Reorientar o reubicar la antena receptora.
—
Incrementar la separación entre el equipo y el receptor.
—
Conectar el equipo a un tomacorriente de un circuito diferente del circuito al que el
receptor está conectado.
—
Consultar al distribuidor o a un técnico con experiencia en radio/televisión para solicitar
asistencia.
Nota importante:
Para cumplir con los requisitos de cumplimiento de exposición de
radiofrecuencia de la FCC, no se permiten cambios a la antena o el dispositivo. Cualquier
cambio a la antena o dispositivo podría hacer que el dispositivo supere los requerimientos de
exposición de radiofrecuencia y anular la autoridad del usuario para operar el dispositivo.
FCC — U2ZZW3005A | IC: 6924A-ZW3005A
Model: ZW3005/39458
CAN ICES-3(B)/NMB-3(B)
Resideo Technologies, Inc.
2 Corporate Center Dr. Suite 100
P.O. Box 9040
Melv ille, NY 11747
www.security.honeywellhome.com
| 1-800-645-7492
Z-W
AvE
® C
ERTIFIED
W
IRELEss
L
IGHTInG
C
OnTROL
C
OMMAnDE

D
’
éCLAIRAGE

sAns

FIL

CERTIFIéE
Z-W
AvE
®
Z-W
AvE
® C
OnTROL

DE
I
LUMInACIón
I
nAL
áMBRICO

CERTIFICADO
Z5DIMMER
ZW3005
https://mywebtech.honeywellhome.com/
SUPPORT
SOUTIEN
APOYO
https://www.security.honeywellhome.com/

hsc/resources/wa/index.html
U.S. WARRANTY
U.S. GARANTIE
GARANTÍA DE U.S.
RIESGO DE INCENDIO
RIESGO DE DESCARGA ELÉCTRICA
RIESGO DE QUEMADURAS
CONTROL DE EQUIPOS
ELECTRODOMÉSTICOS
PRECAUCIÓN
: A FIN DE DISMINUIR
EL RIESGO DE RECALENTAMIENTO
Y DE POSIBLES DAÑOS EN LOS
DEMÁS EQUIPOS, NO INSTALAR
PARA CONTROLAR APARATOS QUE
FUNCIONAN A MOTOR, ARTEFACTOS DE
ILUMINACIÓN DE LUZ FLUORESCENTE
O APARATOS ALIMENTADOS
CON TRANSFORMADORES.
•
USAR EXCLUSIVAMENTE PARA
CONTROLAR BOMBILLAS CFL/LED
INCANDESCENTES O ATENUABLES
•
NO SUPERE LOS VALORES
NOMINALES ELÉCTRICOS
•
NO USAR PARA CONTROLAR
DISPOSITIVOS
•
USE SOLAMENTE EN INTERIORES
RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
CONTROLLING APPLIANCES
CAUTION
: TO REDUCE THE RISK OF
OVERHEATING AND POSSIBLE DAMAGE
TO OTHER EQUIPMENT, DO NOT
INSTALL TO CONTROL A RECEPTACLE,
A MOTOR-OPERATED APPLIANCE, A
FLUORESCENT LIGHTING FIXTURE, OR A
TRANSFORMER-SUPPLIED APPLIANCE.
•
ONLY USE TO CONTROL INCANDESCENT
OR DIMMABLE CFL/LED BULBS
•
DO NOT EXCEED RATINGS
•
DO NOT USE TO CONTROL ANY DEVICE
WHERE UNINTENDED OPERATION
COULD CAUSE UNSAFE CONDITIONS
(HEAT LAMP, SUN LAMP, ETC.)
•
FOR INDOOR USE ONLY
RISQUE D’INCENDIE
RISQUE DE CHOC ÉLECTRIQUE
RISQUE DE BRÛLURES
COMMANDE DES APPAREILS
ATTENTION
: POUR RÉDUIRE LE RISQUE
DE SURCHAUFFE ET DE DOMMAGES
POSSIBLES À D’AUTRES APPAREILS, NE
PAS INSTALLER POUR COMMANDER
UN APPAREIL ACTIONNÉ PAR
MOTEUR, UN APPAREIL D’ÉCLAIRAGE
FLUORESCENT OU UN APPAREIL
ALIMENTÉ PAR UN TRANSFORMATEUR.
•
UTILISER SEULEMENT POUR
COMMANDER LES AMPOULES À DEL ET
FLUOCOMPACTES À INCANDESCENCE
OU À INTENSITÉ RÉGLABLE
•
NE PAS DÉPASSER LES
CARACTÉRISTIQUES NOMINALES
•
NE PAS UTILISER POUR COMMANDER
DES APPAREILS POUR LESQUELS
UN FONCTIONNEMENT IMPRÉVU
POURRAIT ENTRAÎNER DES CONDITIONS
DANGEREUSES (LAMPE À RAYONS
INFRAROUGES, LAMPE SOLAIRE, ETC.)
•
POUR UTILISATION INTÉRIEURE
UNIQUEMENT
AVERTISSEMENT
WARNING
ADVERTENCIA
NOT FOR USE WITH MEDICAL OR
LIFE-SUPPORT EQUIPMENT
Z-WAVE ENABLED DEVICES SHOULD
NEVER BE USED TO SUPPLY POWER TO
OR CONTROL THE ON/OFF STATUS OF
MEDICAL OR LIFE-SUPPORT EQUIPMENT.
NE PAS UTILISER AVEC UN
ÉQUIPEMENT MÉDICAL
OU DE SURVIE
LES DISPOSITIFS COMPATIBLES
AVEC LA TECHNOLOGIE Z-WAVE NE
DEVRAIENT JAMAIS ÊTRE UTILISÉS
POUR ALIMENTER OU COMMANDER
LA MISE EN MARCHE OU L’ARRÊT DE
L’ÉQUIPEMENT MÉDICAL OU DE SURVIE.
SE PROHÍBE SU EMPLEO EN
EQUIPO MÉDICO O EQUIPO
PARA EL MANTENIMIENTO DE
LAS FUNCIONES VITALES
LOS DISPOSITIVOS Z-WAVE NUNCA
SE DEBEN USAR PARA SUMINISTRAR
ENERGÍA ELÉCTRICA AL EQUIPO MÉDICO
O AL EQUIPO PARA EL MANTENIMIENTO
DE FUNCIONES VITALES, NI PARA
CONTROLAR EL ESTADO DE ENCENDIDO
O APAGADO DE DICHOS EQUIPOS.
This product can be included and operated in any Z-Wave network with other Z-Wave certified
devices from other manufacturers and/or other applications. All non-battery operated nodes
within the network will act as repeaters regardless of vendor to increase reliability of the
network.
Ce produit peut être utilisé dans un réseau Z-Wave avec d’autres appareils certifiés Z-Wave
produits par d’autres fabricants et d’autres applications. Tous les nœuds fonctionnant sans
pile au sein du réseau joueront le rôle de répétiteurs, quel que soit le fournisseur, afin de
rehausser la fiabilité du réseau.
Este producto se puede incluir y puede funcionar en cualquier red Z-Wave con dispositivos
de otros fabricantes y otras aplicaciones que cuenten con la certificación Z-Wave. Todos
los nodos que formen parte de la red y que funcionen sin pilas actuarán de repetidores
independientemente del proveedor con el fin de aumentar la fiabilidad de la red.
ZW3005
Power: 120VAC, 60Hz.
Signal (Frequency): 908.4/916MHz
Maximum Loads: 600W, 2-gang 500W or 3-gang 400W incandescent, 150W CFL/LED
Range: Up to 150ft. line of sight between the wireless controller and the closest Z-Wave
receiver module.
Operating temperature range: 32-104° F (0-40° C)
For indoor use only.
Specifications subject to change without notice due to continuing product improvement
SPECIFICATIONS
Z-WAVE INTEROPERABILITY
SPÉCIFICATIONS
INTEROPÉRABILITÉ ENTRE LES DISPOSITIFS Z-WAVE
ESPECIFICACIONES
INTEROPERABILIDAD Z-WAVE
ZW3005
Alimentación: 120VAC, 60Hz.
Señal (frecuencia): 908.4/916MHz
Cargas máximas: 600W, Caja para 2 conexiones 500W,
Caja para 3 conexiones 400W sólo las lámparas incandescente 150W CFL/LED
Alcance: Hasta 150 pies (45.72m) en línea de visión directa entre el control remoto
inalámbrico y el módulo receptor Z-Wave más cercano.
Rango de temperatura de funcionamiento: 32-104° F (0-40°C).
Para uso en espacios interiores solamente.
Especificaciones sujetas a cambio sin aviso debido a continuas mejoras del producto.
ZW3005
Tension : 120VCA, 60Hz.
Signal (fréquence) : 908.4/916MHz
Charges maximales : 600zw, 2 compartiments 500W,
3 compartiments 400W lampes à incandescent 150W CFL/LED
Portée : Distance à vue entre la télécommande et le module de réception Z-Wave le plus
proche allant jusqu’à 150 pi (45.72m).
Plage de températures de fonctionnement : de 32 à 104° F (de 0 à 40° C).
Utilisation intérieure uniquement.
En raison d’améliorations continues du produit, les spécifications peuvent faire l’objet de
changements sans préavis.
This Z-Wave smart dimmer has advanced features that allow you to customize your

experience — these features can only be adjusted by a Z-Wave enabled controller that
supports the Z-Wave configuration command class.
PARAMETERS
NUMBER
SIZE
DEFINITION
VALUE
3
1
Invert/Disable LED
(Adjusts when the indicator
LED is turned ON, OFF, or
disables it entirely)
0 - LED ON/Device OFF
1 - LED ON/Device ON
2 - Disable LED
4
1
Invert switch
(In case switch is installed
upside down)
0 (Default) - Default
(Top ON/Bottom OFF)
1 - Invert switch
(Top OFF/Bottom ON)
7
1
Dim rate steps when using
Z-Wave controller (Adjusts the
number of steps the light level
will stop on when dimming)
3 (Default - 3 steps)
1-99 (Valid values)
8
2
Dim rate timing when using
Z-Wave controller
(Adjusts the timing of each
step in 10ms increments)
1 (Default - 10ms
per step)
1-255 (Valid values)
9
1
Dim rate steps when manually
controlled (Adjusts the number
of steps the light level will stop
on when dimming)
3 (Default - 3 steps)
1-99 (Valid values)
10
2
Dim rate timing when manually
controlled (Adjusts the timing of
each step in 10ms increments)
1 (Default - 10ms
per step)
1-255 (Valid values)
11
1
Dim rate steps when receiving
All-ON/OFF command (Adjusts
the number of steps the light
level will stop on when dimming)
3 (Default - 3 steps)
1-99 (Valid values)
12
2
Dim rate timing when receiving
All-ON/OFF command (Adjusts
the timing of each step in
10ms increments)
1 (Default - 10ms
per step)
1-255 (Valid values)
6
1
Dim up/down rate
0 (Default) = Dim up/down
the light to the specified
level quickly by command
except value 0 and FF
1 = Dim up/down the
light to the specified
level slowly by command
except value 0 and FF
16
1
Enable/Disable switch mode
0 - (Default) Disable
1 - Enable
19
1
Alternate exclusion
0 (Default) = Press any
button on the switch
1 = Press two times
ON button and two
times OFF button
20
1
Minimum dim level
(Set the minimum percentage
the dimmer will go to when
operating it at the switch)
1 (Default)
1-99 (Valid values)
1 = 1%
99 = 99%
MyWebTech
Warranty/Garantie/
Garantía
The Honey well Home trademark is used under license

from Honeywell International, Inc.

This product is manufactured by Resideo.