Honeywell Tuxedo Touch WIFI Installation Manual & Setup Guide

Tuxedo Touch WIFI Home Automation System Installation and Setup Guide

800-10300 11/11

Rev. B

Table of Contents
About the System............................................................................................................................ 5 Safe Mode ......................................................................................................................................... 5 Compatibility.................................................................................................................................... 5 Software Upgrades .......................................................................................................................... 6 System Information ......................................................................................................................... 6 Mounting .......................................................................................................................................... 7 Wiring ............................................................................................................................................... 8 Specifications ................................................................................................................................... 9 Front Panel LEDs ........................................................................................................................... 10 Navigation Icons ............................................................................................................................. 10 Weather Forecast............................................................................................................................ 11 Panel Fault Displays ...................................................................................................................... 12 Initial Setup .....................................................................................................................................13 Programming the Control Panel.................................................................................................... 13 Keypad Initialization ...................................................................................................................... 13 Night Setup ..................................................................................................................................... 14 IP Setup and Network Connections...............................................................................................14 Account Setup ................................................................................................................................. 16 Setup................................................................................................................................................17 Brightness and Volume Control..................................................................................................... 17 Display & Audio Setup ................................................................................................................... 17 Language Selection (if applicable) ................................................................................................. 17 Adjust the Screen Timeouts ........................................................................................................... 18 Clean Screen ................................................................................................................................... 18 Multi-Media......................................................................................................................................19 Picture Setup................................................................................................................................... 19 Camera Setup.................................................................................................................................. 20 Video (Audio) Setup ........................................................................................................................ 22 System Setup..................................................................................................................................23 Power Mode Setup .......................................................................................................................... 23 CS Setup .......................................................................................................................................... 23 ECP Address Selection ................................................................................................................... 24 CS Options / Operating Modes....................................................................................................... 24 Operating Modes............................................................................................................................. 25 Screen Security ............................................................................................................................... 26 Code Authority ................................................................................................................................ 26 Device Events.................................................................................................................................. 27 Panel Configuration........................................................................................................................ 27

iii

Table of Contents (cont’d)
User System Setup.........................................................................................................................28 User Setup....................................................................................................................................... 28 How to Add an Existing User to a Second Keypad....................................................................... 29 How to Delete a User...................................................................................................................... 29 Time/Date Setup ............................................................................................................................. 30 Setting Daylight Savings Time ...................................................................................................... 30 Setting Current Time and Date ..................................................................................................... 30 System Information ........................................................................................................................ 31 Keypad Reset................................................................................................................................... 31 Advanced Setup .............................................................................................................................. 31 Keypad Test..................................................................................................................................... 31 LED Test ......................................................................................................................................... 32 Calibration Test .............................................................................................................................. 33 Z-Wave Test..................................................................................................................................... 33 NIGHT Setup Function .................................................................................................................. 34 Output Setup Function................................................................................................................... 34 Automation .....................................................................................................................................35 Enroll/Adding Z-Wave Devices ...................................................................................................... 35 Enroll/Add a Light, Switch or Outlet Module ............................................................................... 35 Enroll a Door Lock .......................................................................................................................... 36 Enroll a Honeywell Thermostat..................................................................................................... 36 Editing Z-Wave Device Names ...................................................................................................... 37 Edit a Device Module Name........................................................................................................... 37 Remove/Delete Z-Wave Devices ..................................................................................................... 37 Remove a Light, Outlet, or Switch Module ................................................................................... 37 Remove a Door Lock Device ........................................................................................................... 37 Remove a Honeywell Thermostat ..................................................................................................38 Remove All Z-Wave Devices ........................................................................................................... 38 Abort a Z-Wave Action.................................................................................................................... 38 Output List...................................................................................................................................... 39 Scene Setup ..................................................................................................................................... 39 Create a Group................................................................................................................................ 41 Setting a Secondary Keypad (Controller)...................................................................................... 41 Updating Keypads (Controllers) with New or Removed devices ................................................. 42 Removing a Secondary Keypad (Controller) ................................................................................. 42 Z-Wave Troubleshooting................................................................................................................. 42 Compatible Devices......................................................................................................................... 43 Important Notes..............................................................................................................................44

iv

About the System
This guide provides information to install and set-up Honeywell’s Tuxedo Touch WIFI Home Automation and Security System. The graphical touch-screen keypads are Advanced User Interface (AUI) devices, which combine wireless home automation and security. Your system may consist of one or more of the following: • TUXWIFIS Keypad (silver housing) • TUXWIFIW Keypad (white housing) • One or more other keypads for system control • Various sensors for perimeter and interior burglary protection, plus a selected number of strategically placed smoke, carbon monoxide or combustion detectors • Lighting/output devices. Equipped with wireless capability and built-in Z-Wave technology, the Tuxedo Touch wireless keypad can be used to control the home environment, such as lights, appliances, thermostats, door locks and cameras via any web enabled device (PC, Smart Phone and Tablet).

UL

Wi-Fi has not been evaluated by UL.

Note: To the installer, see the "Important Notes" in the Important Notes section of this guide.

Safe Mode

The keypad contains a Safe Mode of operation. In the rare event that the keypad cannot successfully communicate in its graphic mode with the control panel, the Safe Mode is a backup mode that ensures that you can communicate with the system. In this mode, the keypad operates much like a standard non-graphic keypad so that you can control the system until the problem is corrected. • DO NOT perform panel programming while in the Safe Mode. Performing panel programming while in the Safe Mode may cause the panel and keypad to become out of sync. • DO NOT use more than several hardwired motion detectors in high traffic locations. The high quantity of signals received by the panel may cause the keypad to enter the Safe Mode. The actual number of installed detectors depends on the amount of traffic and the number of detectors being used. High traffic can cause Safe Mode with as few as three detectors.

Compatibility

The below listing identifies the alarm systems that the keypad can interface with, the maximum number of keypads that can be used with each system, and the minimum alarm panel software revision level for compatibility. NOTE: For SIA installations used with a VISTA-128BPTSIA Control, see the SIA CP-01 Quick Reference Chart, Document # 800-09699 located at: http://www.security.honeywell.com/hsc/resourses/MyWebTech
Alarm System VISTA-15P VISTA-20P VISTA-20P * VISTA-21IP VISTA-128BP VISTA-128FBP * VISTA-128FBP-9 Maximum Number of Keypads Minimum Software Revision Level

2 2 4 4 3 3 3

3.0 3.0 5.0 1.0 3.2 3.0 4.1

5

About the System (cont’d)
Alarm System * VISTA-250FBP-9 VISTA-250BP VISTA-250FBP VISTA-250FBP * VISTA-128BPE * VISTA-250BPE VISTA-128BPEN * VISTA-128BPLT VISTA-128FBPN VISTA-128BPT VISTA-250BPT VISTA-128BPTSIA FA148CP FA168CPS FA1660C FA1660CT * FA1670C-9 FA1700C * Not evaluated by UL. Maximum Number of Keypads Minimum Software Revision Level

3 3 1 3 3 3 3 3 3 6 6 6 2 4 3 6 3 3

4.1 2.4 3.0 2.0 4.4 4.4 7.0 6.0 5.1 10.1 10.1 10.1 3.0 5.0 3 10.1 4.1 3

Note: Keypad may only be used in the following UL/cUL installations: UL 365, UL609, UL 985, UL1023, UL 1610, CAN/ULC-S303, CAN/ULC-S304, ULC-S545, ULC/ORD-C1023, and ANSI/SIA CP-01-2010. To obtain the software revision level on commercial panels: • From program mode, enter #92 on the keypad (this can be done from the Console Mode). The second line of the keypad displays the software revision level (w/out the decimal point). To obtain the software revision level on residential panels: • From the Home Screen press Setup/System Setup/Central Station Setup/ enter installer code/ press the panel configuration icon; the software revision level is displayed. • The keypad sound suppression feature available in some commercial panels is not compatible with the Tuxedo Touch WIFI keypad. • The ‘Voice Chime’ feature is a residential control feature only. Note: If using the maximum number of keypads, an additional auxiliary power supply may be needed. Refer to the “Wiring” and “Specifications” section for more information.

Software Upgrades

Software upgrades may be available for this product. To ensure you have the latest version, check the version in your system, (see System Information below) then log in to MyWebTech and enter TUXW in the “Search by” “My Product field”; press Go. Click on “Tuxedo Touch software update SBS” and follow the instructions to download the latest upgrade, if necessary.

System Information
ICON

To view the current software/firmware version installed on your system, do the following: ACTION 1. From the "Home" screen, press the Setup icon. 2. Press the System Info icon. NOTES
The Interface Name, Host Name, MAC Address, IP Address, Broadcast Address, and NetMask are also displayed.

6

About the System (cont’d)
Mounting This keypad is for indoor use within the protected area only and should be mounted at a comfortable viewing level. Avoid mounting in areas of high condensation such as bathrooms or in locations where bright light or sunlight shines directly on the screen. The keypad can be mounted with or without the mounting plate. Use the center securing screw for European installations.

1. Select a mounting location. 2. Detach the mounting plate by sliding downward. 3. Use the mounting plate to mark the location of the mounting holes on the mounting surface and check for level. 4. Locate the mounting plate over the mounting surface such that the wire/cable access openings are aligned while passing the wires/cable through the case back. **Go to “Wiring” (next page) and complete wiring** 5. Secure the mounting plate to mounting surface using 4 screws (supplied). 6. Slide keypad onto mounting plate.
MOUNTING SCREWS (4) (TYP) WALL SURFACE

Standard Mounting with mounting plate:

1. Select a mounting location. 2. Detach the mounting plate by sliding downward and discard. 3. Use the template (provided in the carton) to mark the location of the mounting screws and the cut-out for the keypad assembly on the mounting location. Check for level. 4. Install 4 screws (supplied) in the mounting surface leaving screw heads 1/8” above the mounting surface. 5. Locate the case back over the mounting surface such that the opening is aligned with the wire/cable access opening on the mounting surface while passing the wires/cable through the opening in the case back. **Go to “Wiring” (next page) and complete wiring** 6. Mount keypad by sliding onto the screw heads.
WALL SURFACE

Mounting without mounting plate:

6280

SE

RIE

SC

AS

EB AC K
43/4"

TEMPLATE
MO UN TIN G TE MP LA TE

CU

T-O

UT

LOC

ATI

ON

DR

ILL

3/16 " DIA 4 PLA . CESHO

LES

800-

" DIA

LE

WALL MOUNTING PLATE (OPTIONAL)

6280-006-V0

7

6280-016-V0

. HO

3 - 9/16"

Ê8 00 0883 -0 08 1 5/11 31 Rev. uŠ A

DR

ILL

3/16

MOUNTING SCREWS INSTALLED 1/8” ABOVE SURFACE

About the System (cont’d)

Mounting (European Installations) using a center securing screw:
1. Detach case front by removing the two bottom screws. Gently pull up using a screwdriver if necessary and pry apart. Lift off cover. 2. Mount the keypad in its final location, (see “Standard Mounting” or “Mounting without the mounting plate”) install center securing screw (supplied) and tighten to mounting surface. 3. Replace the case front and secure using the two bottom screws. European mounting procedure has UL Thebeen evaluated by UL. not

CASE FRONT

INSTALL CENTER SECURING SCREW

CASE BACK

DETACH CASE FRONT BY REMOVING SCREWS (2) AND LIFT UP

6280-015-V0

Wiring

Connect the Tuxedo Touch in parallel with keypads and other peripheral devices using the keypad data (ECP) bus. • If the Tuxedo Touch is used as the primary system keypad, maximum wire run length is 150 feet. • If more than one keypad is wired to one run, then the maximum lengths must be divided by the number of keypads on the run. (e.g., the maximum length is 75 feet if two keypads are wired on a #22 gauge run). Wire Gauge: Length
#22 gauge #20 gauge #18 gauge #16 gauge 150 feet 240 feet 350 feet 550 feet

The Keypad draws up to 350mA. If you power the keypad from your panel’s Aux Power output, check your panel’s Installation and Setup Guide and verify that this device and others do not exceed your panel's Aux Power output capability. If it does, a supplementary power supply is needed.

8

About the System (cont’d)
Connect the wires to the keypad terminal block as shown below.
CONTROL TERMINAL STRIP AUX AUX DATA DATA IN OUT YELLOW (DATA FROM CONTROL)
Y

POWER FROM SUPPLEMENTARY POWER SUPPLY IF USED SUPPLEMENTARY +12 VDC POWER SUPPLY P/N AD12612 CONTROL TERMINAL STRIP AUX AUX DATA DATA IN OUT

RED (+12VDC) BLACK (GND)

G

RJ45

GREEN (DATA TO CONTROL)

BLACK RED GREEN YELLOW

BLACK

IP CONNECTION

6280i-002-V0

IMPORTANT: When the keypad is powered from an auxiliary power supply, always apply power to the control panel first and then the keypad. Failure to observe this sequence results in improper operation of the keypad and may result in an ECP Error indication. Installer Note: The Tuxedo Touch Screen has been calibrated at the factory. Ignore the “CALIBRATE” button that appears on the “Options” screen after initial ECP setup. If the screen should require recalibration, the end user may do so via the “Keypad Test” screen. See the “Diagnostic Tests” section for instructions. Supplementary external power supply must be Listed to UL603 for UL Burglary Installations and UL1481 for UL Residential Fire Installations. Supplementary external power supply must be Listed to CAN/ULC-S318 for cUL Burglary Installations and ULC-S527 for cUL Residential Fire Installations.

Specifications
Mechanical Specifications:
Width: 8.23 inches (209.04mm) Height: 5.59 inches (141.99mm) Depth:1.13 inches (28.70mm)

Electrical Specifications:
Backlight OFF, Sound OFF Backlight ON, Sound OFF Backlight ON, Sound ON 12V, 140mA 12V, 205mA 12V, 350mA

Operating Environment:
Humidity 93% RH, non- condensing 14˚ F to 131˚ F / -10˚ C to 55˚ C (UL tested 32˚-120˚F / 0 to 49˚C) -40˚ F to 158˚ F / -40˚C to 70˚C

Temperature:
Operating Shipping / Storage

9

About the System (cont’d)
Front Panel LEDs
The Tuxedo Touch Keypad has three LEDs as follows:
SD/SDHC CARD Slot
ARMED (RED) LED ON – System is armed. OFF – System is not armed. READY (GREEN) LED ON – System is disarmed and ready to arm. OFF – System is armed or disarmed but not ready. If disarmed, faults or troubles are present. MESSAGE (YELLOW) LED FLASHING – The system contains new message(s) for the User. OFF – No new messages.

RESET BUTTON Press to reset keypad

6280-001-V0

NOTE: If the Screen Blackout (*EN50131 Display) feature is enabled (see below) the keypad returns to the “Home” screen and the “Armed” and “Ready” status LEDs turn OFF after 30 seconds. The keypad will remain in this state until a valid user code is entered. *The EN50131 Display compliance feature is a European Standard designed to prevent unauthorized users from viewing the status of the Security System.

Navigation Icons
ICON

To aid in the navigation through the Tuxedo Touch WIFI screens, a set of user-friendly icons has been provided. The appearance and function are described below. ICON TITLE “Product/Training Videos” "Message" FUNCTION Accesses the “Product Introduction and Training Videos”.

Record and retrieve Voice Messages.

"Automation"

Accesses the Z-Wave setup, Scene setup, and Group setup screens.

"Security"

Accesses the "Security" screen.

10

About the System (cont’d)
ICON ICON TITLE “Home” FUNCTION Returns you to the "Home" screen.

“Back”

Reverts to the last screen viewed. Displays Emergency functions (as programmed by the installer). See programming the Control Panel note.

“Panic”

Note: This icon is displayed and active on all screens except while in the Clean Screen mode, during an LCD Display test in Diagnostics, and from the Video and Camera screen.

“Control Panel Message” “Setup”

This icon alerts the user to a Control Panel Message.

Accesses the Setup menus.

“Multi-Media” “Video”

Accesses the Message, Camera, Picture and Video features. Allows user to play video files.

“Picture”

Allows user to display personal photos in a slide show format.

“Voice Status” “Minimize Home” “Maximize Home”

Allows user to hear system status. Minimizes the Home screen icons when viewing wallpaper displays. Maximizes the Home screen icons when viewing wallpaper displays.

Weather Forecast The weather forecast is displayed on the “Home” screen. To change locations, press the Weather feature on the Home screen. Select USA/Canada, and then select Zip Code or Postal Code. Enter required information on the data entry keyboard. Press the Back icon. The four day weather forecast for the location entered is displayed. Use the Refresh icon to update the screen.

11

About the System (cont’d)
Panel Fault Displays
ICON The “Security” screen displays an Icon(s) if a panel fault(s) occurs. The following Icons(s) may be shown as applicable to your system: MEANING AC Loss – The system is not receiving AC power. Bell Failure – The system bell or siren has a problem. Note: This Icon is displayed when interfacing with residential panels only. Expander Failure – The system has a failure in an expansion module. Low Battery – The system battery, that powers the system during an AC power loss, is low. LRR Supervision Failure – The Communication Device used to communicate with the central station has a supervision failure. Max Attempts Exceeded – The system has exceeded the maximum attempts to communicate with the Central Station. Pager Failure – The system cannot communicate with an assigned pager. Telco-1 Cut – The system is not able to communicate with the central monitoring station over the primary phone line. Telco-2 Cut – The system is not able to communicate with the central monitoring station over the secondary phone line. Wireless Failure – The system is not able to communicate with its wireless devices. Note: If multiple faults exist, press the More Choices icon and then the Show Zones icon to view and scroll through the complete list of faults.

12

Initial Setup
Programming the Control Panel
The keypad is not fully operational unless its address in the control panel has been enabled (set as an alpha console) AUI type device, and assigned to a partition (where applicable). For a list of alarm systems that the keypad can interface with, refer to the “Compatibility Table” in Section 1 of this document for the quantity of keypads that may be used and the required control panel software revision level. We recommend that you use either a standard alpha keypad or the keypad in Console Emulation Mode when programming the control panel. When in the Console Mode, the keypad emulates an alpha keypad and the programming of the panel is performed following the procedures provided in your panel’s Installation and Setup Guide. Note: When programming your control panel, if you change the zone types for your emergency zones you may disable the emergency buttons in the keypad. The emergency buttons in the keypad are active for zone types 06 (Silent Panic Button), and 07 (Panic Button), 08 (Medical Button), and 09 (Fire Button). Additionally, the Medical button is also compatible with a zone type 15 (24-Hour Medical) for panels that contain this zone type.

On residential control panels (VISTA-20P or equivalent):
Up to four keypads may be used (addresses 1, 2, 5 and 6). Addresses 1 and 2 (in field *189) are enabled by default. If the defaults have been changed, enable these addresses (in field *189) using an alpha-keypad and the Data Field Programming procedures located in the panel Installation and Setup Guide.

On commercial control panels (VISTA-128BP, VISTA-128FBP, or equivalent):

Addresses 1-2, and 3-30 may be used for older controls under Rev. 10 supporting 3 AUI’s, see Important Note below. Addresses 1-30 may be used for commercial Turbo controls Rev. 10 and higher supporting 6 AUI’s. These addresses in the control panel are normally not defaulted for AUI type devices. To enable the addresses you are using for keypads, use an alpha-keypad and follow the procedures for “Device Programming” in your control panel “Programming Guide.” Important Note: If multiple keypads are being used, they must be set to addresses 1, 2, and X (where X equals any address from 3 through 30). Only one AUI type device may be assigned to an address from 3 through 30 on commercial control panels. The Keypad should not be assigned as a Master Console. If the keypad is assigned as a Master Console, partitions must be controlled from the Partition screen or using the Console Emulation Mode. When initially powered, the screen displays the boot sequence and the "Set ECP Address" screen is displayed. If the system is incorporating only one keypad, leave the address set to 1 and press Apply. The boot-up process continues until completion. If there are to be additional keypads in the system, after enabling addresses in the control panel using an alpha-keypad, power-up each keypad one at a time, and set its address to one of the addresses you enabled in the control panel. Language Selection (if applicable) After initial ECP selection is set, the “Languages” menu is displayed. The Tuxedo Touch keypad allows you to select from four languages (English, French Canadian, Latin American Spanish, or Latin American Portuguese) with the default being English. Time and Date Setup

Keypad Initialization

If not already set from the control panel, set the current time and date. Refer to Time/Date Setup. 13

Initial Setup (cont’d)
Night Setup
The Keypad is defaulted to arm the system in the STAY INSTANT mode when arming the system using the NIGHT icon. Select the arming mode to be activated when the NIGHT icon is pressed on the “Arming” screen, refer to the “Night Setup” section.

IP Setup and Network Connections
Web Server/Hosting The Tuxedo Touch keypad offers built-in web hosting capability to access your Security and Home Automation System via any web enabled device. The Tuxedo Touch Keypads IP Address is used on a standard web browser to control user functions. Supported Browsers include: iPhoneTM Version iOS4, i-PadTM Version iOS4 and iOS5, Galaxy – Android 2.3, Internet Explorer 8 and Safari® 5.0.2. Supported Routers include: 1. Netgear Model: WNR2000V3; Mode: None, WEP (64 bit & 128 bit), WPA personal, WPA2 personal, and Tx Key 1, 2, 3, 4. 2. D-Link Model: DIR-632; Mode: None, WEP, WPA personal, and WPA2 personal. ® 3. Linksys Model: WRT54GL; Mode: None, WEP, WPA personal, and WPA2 personal.

UL

• •

Web Server/Hosting is not Listed for use in UL installations. Remote Arming/Disarming/Programming is not to be used in UL Listed Installations.

IP Address Setup In most cases, IP Addresses are assigned ‘automatically’ (Automatic IP Address). Or, you may require a “Static” (Fixed) IP Address that can be found by accessing your router. Refer to your router instructions for further information. To connect a mobile device to the Tuxedo Touch keypad, view the “Local System Control (Tablet/Smartphone)” training video, and then do the following: ACTION 1. At your Smart Phone or Tablet: a) Navigate to the Settings feature. b) Turn ON the “Wi-Fi” setting and select the router to connect to. Enter a name and password, if required. c) Open the browser and enter the IP Address displayed on the keypad into your browser. Or, 2. At your PC: a) Open the browser and enter the IP Address displayed on the keypad into your browser. NOTES
After proper connection: • Access to basic arming commands is available if using a Smart Phone or Tablet browser. • Full access to keypad options is available if using a PC browser. • If left inactive, Web connections disconnect after 10 minutes. The IP Address is displayed in the lower left-hand corner on the Tuxedo Touch Keypad “Home” screen. NOTE: If using an iPad, iPhone or PC browser with low bandwidth on the mobile type theme, to switch between normal theme and mobile theme, go to the Home page on the Web browser and press the Switch Theme icon; the user interface displays the mobile theme. Web themes for Android phones and Tablets are not supported.

14

Initial Setup (cont’d)
Network Connections To set up network connections, from the “Home” screen, and do the following: ICON ACTION 1. At the Tuxedo Touch keypad: a) Press the Setup icon. b) Press the IP Setup icon. 2. Select a type of network connection: LAN ON or WIFI ON and go to that section below for further information. NOTES
A pop-up window displays the message: Save the Change Select Yes to save the settings.

Setup a LAN Connection From the IP Setup screen, add a LAN network connection as follows: ICON ACTION NOTES 1. At the Tuxedo Touch keypad: A pop-up window displays: This will switch off WLAN Network, do you want to a) Press the LAN ON button. continue? Yes or No - Select Internet Connection type Use the Data Entry Keyboard to enter the required “Obtain address automatically” (to information. have the keypad begin to scan for • Press the “up arrow” to switch to capital letters. existing networks to connect to • Press the Space key to add a space between automatically). characters. • Press the x key to delete/backspace. - Select Internet Connection type • Press the ABC/123 key to switch between Static IP and highlight the IP numerals and symbols/characters. Address field to enter a Fixed IP • Press GO to return to the IP Setup screen. address on the “Data Entry Note: To change the default port number (6280), Keyboard” and press GO. Highlight press the field next to port number and on the data the remaining fields and enter the entry keyboard enter a secondary port number between 5000-65534. Press GO and then press Save. required information for Subnet A pop-up window displays: Mask, Default Gateway, DNS Success Network Details Saved Server and Port #. Port number changed. Keypad is going to reset 2. Press the Save icon; the IP The keypad will reboot with the newly configured port information will automatically update. number. This may take up to 60 seconds. 3. At your PC, Smart Phone or Tablet browser, start your browser and enter your IP Address.

15

Initial Setup (cont’d)
Setup a WLAN (Wi-Fi) Connection From the IP Setup screen, add a WLAN network connection as follows: ICON ACTION NOTES 1. At the Tuxedo Touch keypad: A pop-up window displays: This will switch off LAN Network, do you want to a) Press the WIFI ON button. continue? Yes or No - Use the scroll bar to locate a network Use the Data Entry Keyboard to enter the required from the list of Wifi Networks to information. connect to and highlight that field. • Press the “up arrow” key to switch to capital letters. Press the Refresh icon until available • Press the Space key to add a space between networks are displayed. characters. - Or, select Add Network and highlight • Press the x key to delete/backspace. • Press the ABC/.?123 key to switch between each field to enter the required numerals and symbols/characters. information for SSID, Security Mode, • Press GO to return to the IP Setup screen. Passphrase/Shared Key, and Port # on A pop-up window displays: the “Data Entry Keyboard” and press Network Details Saved GO. A pop-up window displays the message: Settings saved. 2. Press the Save icon; the information Select OK to save. will automatically update. This may Note: To change the default port number (6280), take up to 60 seconds. press the field next to port number and on the data 3. At your PC, Smart Phone or Tablet entry keyboard enter a secondary port number browser, start your browser and enter between 5000-65534. Press GO and then press Save. A pop-up window displays: Success Network Details your IP Address. • If left inactive, Web connections disconnect Saved Port number changed.
after 10 minutes. Keypad is going to reset The keypad will reboot with the newly configured port number.

Account Setup Account setup provides a browser log-on page for higher security when viewing from a PC, Smart Phone or Tablet. Up to 5 accounts can be created. To set up a user account, do the following:
ICON ACTION 1. Press the Account Setup button. 2. If required, highlight the User Name/Password fields on the screen and enter the data for each on the “Data Entry Keyboard”; press GO. 3. Press the Save icon. The new user is displayed on the screen. 4. Press the Clear button to clear the User information. NOTES
Note: A password is required if logging in from a remote location (not using the premises network). A Confirmation window displays the message: Settings saved. The ENABLED button is displayed when a successful network connection is completed.

16

Setup
You may access Brightness and Volume, Display & Audio Setup, System Setup and IP Setup from the "Setup" screen.

Brightness and Volume Control
ICON

From the "Home" screen, access the "Setup" screen as follows: ACTION 1. From the Home screen, press the Setup icon. 2. Move the Brightness/Volume slide bar up or down to increase or decrease settings. Yes saves the change. No discards the change. NOTES
If changes are made, when you exit a pop-up window displays: “Information Settings saved“

Display & Audio Setup
From the Display & Audio Setup feature you may access Operating Modes, Language,

Backlight Off After Time, To Homepage After Time, Auto Slideshow After Time, and Clean Screen.
Operating modes provides access to Chime Mode, Voice Mode, and Voice Chime. • Chime Mode – Keypad chimes whenever a door or window is open. • Voice Mode – Keypad voice annunciates whenever a change in system status occurs such as Armed, Disarmed, or Alarms. • Voice Chime – The chime mode and voice mode are in effect. The chime beeps followed by voice annunciation. From the Home screen, press the “Setup” icon, and do the following: ICON ACTION 1. Press the Disp & Audio Setup icon. 2. Enter your Authorized Code, if required. NOTES
If the Chime Mode and Voice Mode are both selected, the Voice Chime is automatically selected. When the keypad exits the “Operating Modes” screen, your selection is saved. It may take a few seconds for the Chime Mode to take effect.

3. Select Chime Mode or Voice Mode to turn the mode on or off. 4. Press the HOME or BACK icon after making your selection. Language Selection (if applicable) Set the Language feature as follows: ICON ACTION 1. From the Home screen, press the Setup icon. 2. Press the Disp & Audio Setup icon. 3. Enter an Authorized Code. 4. Press the Language field, and select a language.

NOTES
If applicable, after the language is selected, the keypad will revert back to the “Home” screen with the selected language applied.

17

Setup (cont’d)
Adjust the Screen Timeouts
When the keypad is left idle, it automatically: • Turns the “Backlight Off After” the selected backlight off time has expired (unless “Never” option is selected). • returns to the “Home” screen after the selected “To Homepage After” time has expired (unless “Never” option is selected), and • if enabled, the “Auto Slideshow After” time begins the slide show. To select the desired screen timeouts, do the following: ICON ACTION 1. From the "Home" screen, press the Setup icon. 2. Press the Disp & Audio Setup icon. 3. Enter your Authorized Code. 4. Press the desired selection from the dropdown list displaying the time period for each option. 5. Press the Save icon to save the settings.
If changes are made, when you exit a pop-up window displays: “Information Settings saved“

NOTES
Settings include: • Backlight Off After X time • Return To Homepage After X time • Auto Slideshow After X time. Notes • The “To Homepage After” Time option is only available if the Screen Blackout (EN50131 Display) option is not enabled by the installer. • When in EN50131 mode, “Auto Slideshow After” is preset to “1” minute and can not be changed.

Clean Screen

With the exception of normal cleaning, the keypad is maintenance free. Press the “Display and Audio” icon, and do the following: ICON ACTION 1. Press the CLEAN SCREEN icon. A pop-up window displays "Touch Screen has been
disabled so that you may wipe the screen clean. Please use a damp, soft cloth. DO NOT use any liquids, sprays, or ammonia-based cleansers. Press CONTINUE to disable touchscreen." *Panics cannot be initiated during this process*

NOTES
When the "Continue" icon is pressed the message "Touch Screen Disabled for =30 Seconds" is displayed. During these 30 seconds the touch screen should be wiped clean of fingerprints using a mild soap solution and a soft cloth. When the counter reaches zero, the window automatically closes and the touch screen is active.

2. Press Continue or Cancel to exit. IMPORTANT: Do not use an abrasive cleaning agent or abrasive cloth when cleaning the keypad or damage to the touch screen may occur. The Emergency screen cannot be accessed while running in the clean screen mode.

18

Multi-Media
This feature allows you to access voice messages, play video files, display personal photos in a slide show format, and view up to four cameras at one time from your keypad.

UL

Multi-Media functionality is supplementary only and has not been evaluated by UL.

Picture Setup

The Picture feature allows the user to display up to 1000 personal photos on the touch-screen and can be accessed from the Home screen by pressing the Picture icon, or access this feature as follows: ACTION 1. Insert your personal media (SD/SDHC) card (with stored picture files) first. 2. Press the Multi-Media icon and then press the Picture icon. 3. Press the Transition arrow to select the type of viewing transition desired (Standard, Horizontal, Vertical or Fade Out). 4. Press the Slide Delay arrow to select the time interval that you want to allow between each photo being viewed. Choose from (5, 10, 15, or 20 seconds). 5. To add an image to the slide show, select the image from the list and press the Add Image icon; the image appears on the screen and a check mark appears next to the selected image name on the list. 6. To remove an image from the slide show, select the image, and press the Deselect Image icon. To set a picture as wallpaper: 1. Use the slide bar to highlight the file you want to be displayed on the keypad screen. 2. Press the Set Wallpaper icon; view your selection from the “Home” screen. Picture Icons ICON NOTES
Photo files can be viewed from the (SD/SDHC) Card. Formats supported are .bmp, png or .jpg files. NOTE: • To exit slide show at any time and resume keypad operation, press anywhere on the screen. • The first image is displayed and a list of stored images appears on the screen. • When an image is loading, no other Picture Setup function can be performed (play, previous, next, add or set wallpaper). Press the TOP button to move up one level in the directory. Press the OPEN button to view larger images and/or open directories, select from the list of stored images. Press the CLEAR ALL button to clear all pictures from the current slide show rotation. NOTE: On the “Home” screen press the Minimize Home icon to reduce the “Home” screen icons and to have better visibility of the Wallpaper. Press the Maximize Home icon to maximize the “Home” screen icons.

Play Image

Previous Image

Next Image

Add Image

Deselect Image

Set Wallpaper

Minimize Home

Maximize Home

19

Multi-Media (cont’d)
Camera Setup
The Camera feature allows you to enroll cameras and view up to four cameras at one time using the quadrant view feature. If using existing (mounted) cameras, go to Step 4 below. If this is a first time setup, scan/configure the cameras prior to mounting. View the “IP Camera Setup” training video and then follow the steps below.

UL

Camera functionality is supplementary only and has not been evaluated by UL.

IMPORTANT: Use the web browser to view cameras for non-security purposes only. Camera streams viewed from the web browser can stop without indication due to network connection issues. ICON ACTION NOTES Notes: 1. Connect an Ethernet cable to the back of your camera (LAN); connect 1. QuickTime® media player must be installed on your PC. 2. Camera viewing is not compatible if using Opera web the opposite end to the Ethernet browser. Port on your router. 3. Do not use ports 6665-6669 for camera HTTP 2. Apply power to the Camera. Wait configuration. These ports block MPEG streaming and PT a few seconds for initial power-up commands of Safari based PC and mobile devices. of camera. Note: Some older versions of these cameras may need a 3. Press the Multi-Media and Camera firmware upgrade; see separate instructions. Use the Data Entry Keyboard to enter all required icons (or press the Camera icon information. from the “Home” screen) and then • Press the Up Arrow key to switch to upper case characters press the Camera Setup icon. • Press the X key to delete 4. Press the Discover icon to locate • Press the ABC/.?123 key to switch between numerals and cameras. The screen displays: symbols/characters.
“Discovering Cameras Please Wait…”

5. Press the Add icon if the camera information is not discovered automatically, to enter information on the “Add New Camera” screen. 6. To edit information, highlight the camera name and press the Edit icon. Highlight each field and enter the required information, and then press Save. a) To retrieve camera settings and connect to the camera, press the Connect icon. b) Press the Total Connect icon to reset the camera for remote viewing and activate a Total Connect account. c) Press Save. d) Use the Refresh icon to update the screen.

• Press GO to return to previous screen. Note: For best performance set video resolution to 320 x 240, 8 frames per sec, Normal quality. Add/Edit Options: Name: Enter a camera name. Address: Enter IP or URL. RTSP Port #: Select from (554, (1024-65534)). Model: Select iPCAM-WI, iPCAM-WI2, iPCAM-WI2B (black), iPCAM-WO or iPCAM-PT, WVC210, other. User Name: Enter a user name, if desired. Password: Enter a user password, if desired. Resolution: Select from 160 x 120, 320 x 240 or 640 x 480. Frame Rate: Select from 1, 2, 3, 4, 5, 6, 8, 10, 15, 20, 25, or 30. *HTTP Port Number: Default value = 80. To change enter valid port number (80 (1024-65534)). A pop-up window displays: “For remote camera viewing service, please contact your alarm company and ask for Total ConnectTM service and provide the camera’s MAC ID XX:XX:XX:XX:XX:XX. Press continue to prepare the camera for Total Connect service.” Press CONTINUE or CANCEL. If you press Continue a confirmation window displays: Do you want to reset the Camera? Yes or No.

20

Multi-Media (cont’d)
ACTION 7. When all cameras have been added, press the Camera WIFI icon to enter the camera wireless settings information from your router. 8. Press Apply to All to set cameras for wireless operation. 9. Press the Save icon. 10. Press the Settings icon to enter Video, Network, Wireless, and Other settings; refer to “(Advanced Camera) Settings” below. 11. Remove the Ethernet cable from the wireless cameras to view wirelessly via the Tuxedo Touch Keypad. If the camera does not have wireless capability, leave the camera connected to router. Camera Setup Icons ICON NOTES
The screen displays: “INFO: Camera wifi setup is applicable only for discovered cameras” Enter the appropriate wireless information. SSID: ANY Security Mode: Disabled, WPA personal, WPA2 personal, or WEP. Network Type: Infrastructure Domain: USA Channel: Auto For Security Mode information enter: Tx Key: 1, 2, 3 or 4. WEP Encryption: 64 bit Key (10 Hex Chars) or 128 bit Key (26 Hex Chars). Authentication: Open System or Shared Key. Passphrase; then press GO. A pop-up window displays: “Info XXX.XXX.X.X WIFI Configuration Saved”

DISCOVER

ADD

EDIT

DELETE

DELETE ALL

SETTINGS

CAMERA WIFI

BACK

Camera Icons

Add/ Edit Icons

AUTO QUAD PLAY FULL STOP CAMERA PAN/TILT SAVE CONNECT RESET PAN VIEW VIEW SETUP Camera Notes: • To use the Pan/Tilt feature in Quad View, select the camera name from the camera list and then press Pan/Tilt. • Press the Quad View icon to enter quad mode. Select a quadrant area on the screen (this area is highlighted) and then select the camera that you want to appear in that quadrant. • To remove a single camera, highlight the camera name and press DELETE. To remove all cameras, press DELETE ALL. (Advanced Camera) Settings Press Save! after each selection. Note: Cameras must be enrolled to access the Settings screen. If multiple cameras are enrolled, highlight the desired camera to make changes. Video Settings: Select the following: MPEG-4 Settings: Resolution, Fixed Quality and Max. Frame Rate MJPEG Settings: Resolution, Fixed Video Quality and Max. Frame Rate Network Settings: To make changes to the selected camera. Internet Connection type: If set to Obtain an address automatically, selectable options are Enable Discovery for UPNP, HTTP Port, RTSP Port. If set to Static IP, options are IP Address, Subnet Mask, Default Gateway, Enable Discovery for UPNP, HTTP Port, RTSP Port. Wireless: View the following settings: SSID, Security System, Passphrase/Shared Key, Network Type, Domain and Channel Information. Others: Reset to Defaults: a pop-up window displays: “Do you want to reset the Camera?” Select Yes to reset the camera to factory default settings. Restart Camera: Press to restart the camera.

21

Multi-Media (cont’d)
Video (Audio) Setup
View the “SD Card Video Playback” training video and then access the Video (Audio) feature, by doing the following: ICON ACTION 1. Insert your personal media (SD/SDHC) card (with stored video files). 2. Press Multi-Media and then press the Video icon. 3. Highlight a video file from the list and press Play to start the selected video file. 4. Press the Repeat icon to continually replay the selected video. 5. Deselect the Repeat icon to automatically play the complete list of video files starting with the first video and ending with the last. NOTES
A Video Converter is required to convert videos for proper playback on the Tuxedo Touch Keypad. Use an Internet search engine to locate and download a Video Converter, then follow the steps in the Video Converter Instructions (provided in the carton). Notes: • Supported video playback formats include MPEG4 and H.264, containers AVI, MOV, MP4. • Maximum video resolution should not exceed 400 x 240. • If the video file causes the keypad to lock, use a small object (such as a paper clip) to press the reset button located in the lower right-hand side of the keypad to reset the keypad. • Videos can not be played when the EN50131 Display is turned ON. • To exit Full View mode at any time while a video is playing, press anywhere on the screen. • When in Full View mode there is an 8-10 second delay for video display. Use the slide bar to scroll through the video list. Play Pause Full View Stop Repeat Press the appropriate icon to Play, Pause, view a Full View, Stop or Repeat the video.

Video Icons

22

System Setup
From System Setup, you may access Power Mode Setup, CS Setup, User Setup, Time/Date Setup, and Advance Setup.

Power Mode Setup
Power Setup Mode allows you to reduce power consumption in the event of a system trouble such as AC Loss or Panel Low Battery. To access Power Mode Setup, from the “Home” screen do the following:
ICON ACTION 1. Press the Setup icon and then the System Setup icon. 2. Press the Power Mode Setup icon. 3. Enter your Authorized Code, if required. 4. Select Power Save Mode to enable; then choose from the options. 5. Press Apply to save settings. NOTES
Select from: • Turn-off Network • Override Display Settings: When selected, Display settings are overwritten and the keypad operates in low power mode: - Brightness/Volume controls decrease to minimum levels. - Return To Homepage After time resets to 30 seconds. - Auto SlideShow After time reverts to Never. When AC power is restored, the original Display settings resume.

CS Setup
You may access ECP Address, CS Options/Operating Modes, Screen Security, Device Events, Code Authority and Panel Configuration from the CS Setup screen. From the “Home” screen, press the Setup and System Setup icon and perform the following: ICON ACTION 1. From the System Setup screen, press the CS Setup icon. 2. Enter your Authorized Code, if required. 3. Press the ECP Address icon. NOTES
If the top of the screen is displaying “ECP Error”, the ECP address in the keypad is not valid for the panel that it is connected to. In this case, to change the ECP Address, enter the default code of “4140” to advance to the next screen. Note: Default code “4140” is the Tuxedo Touch default installer code before connecting to a control panel. Once connected to a control panel, use that panel’s installer code.

23

System Setup (cont’d)
ECP Address Selection After enabling addresses in the control panel using an alpha-keypad, power-up each keypad one at a time, and set its address to one of the addresses you enabled in the control panel. Otherwise, access the Central Station screen then follow this procedure to change the address on the unit. To change the address, perform the following: ICON 1 2 3 ACTION 1. Press the ECP Address icon. 2. Select the ECP address for this keypad using the Up/Dn arrows. 3. The available ECP addresses are: 1-2, 5-6 for residential controls 1-2, 3-30 for older commercial controls under Rev. 10 supports 3 AUIs. *See Important Note below. 1-30 for commercial Turbo controls Rev. 10 and higher supports 6 AUIs.
*IMPORTANT: If multiple keypads are being used, they must be set to addresses 1, 2, and X (where X equals any address from 3 through 30). Only one AUI type device may be assigned to an address from 3 through 30 on commercial control panels.

NOTES
When the keypad cannot communicate with the alarm panel, the message “ECP Error” is displayed, check the following: • Verify that the AUI type device is enabled in the control panel, and that the ECP address in the keypad matches the address enabled in the control panel. Use a different address for each device. • If powering the keypad from a power supply, make sure you have a common ground installed (wiring between Power Supply "gnd" and panel "Aux. power neg"). NOTE: When the ECP address is changed, and Apply is selected, the keypad resets. The keypad should not be assigned as a Master Console. If it is, partitions must be controlled from the Partition screen or using the Console Emulation Mode.

NOTE: If using remote services, one of the touch-screen device (AUI) addresses is used by the control panel. Refer to control panel Instructions for specific configuration.

CS Options / Operating Modes

The "CS Options" menu allows you to enable Lighting and the EN50131 Display feature. The "Operating Modes" menu allows you to access "Normal Mode", "Safe Mode" and "Automation/Demo Mode".

Screen Blackout Feature (EN50131 Display)
The Screen Blackout (EN50131Display) compliance feature is a European Standard designed to prevent unauthorized users from viewing the status of the Security System. When the EN50131 Display is turned ON: • The keypad returns to the "Home" screen after 30 seconds; "Armed" and "Ready" LEDs turn OFF. • The "To Homepage After" time setting changes to 30 seconds and the time is non-selectable. • The “Auto Slideshow After” is preset to “1” minute and can not be changed. • The Security, Message and Lighting screen does not display system status until an authorized user code is entered. • The "Setup" menu does not display system status until an authorized user code is entered. • Videos can not be played.

24

System setup (cont’d)
From the Home screen, press the Setup and System Setup icon. ICON ACTION 1. Press the CS Options icon. 2. Enter your Authorized Code, if required. 3. Select “Lighting" or "EN50131 Display" to turn the option on or off. 4. Select "Normal Mode" or "Safe Mode" to turn the option on or off. Apply accepts all changes. NOTES
Note: The Automation/Demo Mode option allows the automation and multi-media features to operate in a non-security mode. When this option is selected, the keypad does not communicate with the control panel and any user can select Advanced Setup screens.

Operating Modes Safe Mode Automatic Entry

The Safe Mode may be automatically entered by the program on a communication failure or may be entered manually on command. In the rare event that the keypad cannot successfully communicate in its graphic mode with the control panel, the screen presents you with a message of “Problems detected. Start Keypad in Safe Mode?” and requests a “Yes” or “No” response. If you answer with “Yes”, the keypad goes into the Safe Mode. If you answer with “No”, the keypad tries to communicate with the panel again. After 3 consecutive times of receiving no response, the keypad enters the Safe Mode automatically.

Manual Entry

Note: ONLY enter the Safe Mode from the Normal Mode. Entering the Safe Mode from the Automation/Demo Mode may result in incorrect display of the Emergency Function keys. ICON ACTION NOTES ! SAFE MODE ! The “Warning” message "Keypad will reset to 1. Select Safe Mode and then press Apply. activate changes" is displayed. 2. Press OK. The keypad resets and restarts in the Safe 3. To exit, touch the safe mode button and Mode. touch Yes to return to Normal Mode.

Operating in the Safe Mode

While in the Safe Mode, the Home screen displays the Security Icon, Panic Icon, and Message Icon. A message at the lower left side of the screen is displaying: !SAFE MODE! This is a limited mode of operation. While in this mode: • You can use the Security icon to access the Console Emulation Mode of operation to try to clear your faults, disarm the system, or enter additional Alpha Keypad commands specified in your panel User and Installation Guides. You can perform almost all functions that you can perform from a standard non-graphic alpha keypad. • You can press the “Panic” icon and generate Emergency Messages as defined in the panel's home partition for this keypad.

Note: Z-Wave Scenes do not function in Safe Mode. WARNING: The Slide Show feature does not start automatically in Safe Mode.

• The Armed and Ready LEDs on the front of the keypad indicates the keypad’s home partition status. • The Chime mode functions in the Safe Mode: however, you do not have Voice (system status messages), Voice Chime (announcements) or Message capability (if set to default “Master”).

25

System Setup (cont’d)
Screen Security
The Screen Security icon displays a list of authority levels and the user level that has been given access to them. To view and/or edit Screen Security, do the following: ICON ACTION NOTES 1. From the System Setup screen, press Note: The Screen Security screen contains a heading of Advanced Setup, Central Station Setup, the CS Setup icon. Disp. & Audio Setup, Event Logs, Lighting, 2. Enter your Authorized Code. Message, Security, or Time/Date highlighting the 3. Press the Screen Security icon. 4. If authority levels are correct, press BACK or Home to exit the menu. 5. If changes are necessary, select the line to be changed and the level of user to have access; then press Apply. Residential Panels and Screen Security
Access Level Chosen in Keypad Screen Security Authority Level in Panel Operator C Yes Yes Yes No Yes No Operator A Operator B Yes Yes Yes No Yes No Manager Yes Yes No No No No Matching Authority Level in Keypad Master Master Normal N/A Guest N/A line was selected for change. The Screen Security screen is re-displayed listing any changes. Note: The User Levels listed on this screen match the User Levels in commercial panels. See the following chart for corresponding User Levels in Residential Panels.

Installer

System Master Partition Master Standard User Arm Only Guest Duress

No No No No No No

Yes Yes No No No No

Master

Yes Yes Yes No No No

Code Authority
The Code Authority screen displays User Names and Partition Authority Level for the User Code. To view the Code Authority level, do the following: ICON ACTION 1. Press the Code Authority icon. 2. Enter the 4-digit User Code for the user that you want to obtain Authority Level information about. 3. Press BACK. NOTES
Note: If the User Code entered is not active in the system, an “INVALID” message will be displayed.

26

System setup (cont’d)
Device Events
Your keypad has the ability to record events in a history log. Each event is recorded with the time and date of its occurrence. To view the Device Events, perform the following: ICON ACTION 1. Press the Device Events icon. A list of events is displayed. NOTES
To view a record of events in a history log, slide the scroll bar down. The Date, Time and Description of each event is displayed.

The Panel Configuration screen displays the configuration of the panel. To view the panel configuration, do the following: SCREEN ACTION 1. Press the Panel Configuration icon. 2. If correct, press Back to return to “System Setup” screen. NOTES
A "Panel Configuration" screen is displayed providing details of your system. Delete clears the configuration from the keypad and reloads the panel configuration into the keypad from the panel. After you press Delete, a confirmation screen is displayed.

Panel Configuration

27

User System Setup
User Setup provides access to Add a User, Delete a User, and Edit a User.

User Code Setup

Each user must be assigned a name with a corresponding 4-digit user code in order to gain access to various features and functions. The keypad can hold the identity for 10 Users in its memory. If additional Users are needed, define the additional Users using the Console Emulation Mode. Users for the system are programmed in a central user setup location that provides the specific questions for authorization levels assigned to different users. You may want these users to be the same, but there are situations in which you may want a user to have limited capabilities. These capabilities are defined by the Authority Level assigned to each user.

Authority Levels

Authority levels define the system functions a particular user can perform. Depending on the authority assigned to you, there are certain system functions you may be prohibited from performing. The following information describes the authority levels available in the keypad and provides the equivalent authority level name found in your alarm system manuals. The authority levels available in the keypad are as follows:
Keypad Authority Level Installer Functions Can perform all security functions except can only disarm if code was used to arm, can change Master Code, cannot change other user codes, can access the Central Station Screen options Note: This authority level cannot be assigned using the keypad. Can perform all security functions, add/delete users in assigned partition, program scheduled events, and change partition master code. Perform security functions (arm, disarm) Can arm the system in assigned partitions, but cannot disarm the system unless the system was armed with this code. Note: Do not assign this level if Quick Arm is enabled in the system. Used to restrict access to a partition. Equivalent System Name Residential Commercial Systems Systems Installer Installer

Master

Partition Master

Level 1 Master

Normal Guest

Standard User Guest

Level 3 Operator A Level 4 Operator B N/A

No Access

N/A

Note: The authorized code for deleting, adding, and editing users is dependent upon the alarm panel you are interfacing with. Check your alarm panel Installation and Setup Guide to determine who can delete, add, and edit users.

User Setup How to Add a User
ICON

To add a user, from the "Home" screen press the Setup icon, and do the following: ACTION 1. From the "Home" screen, press the Setup icon. 2. Press the System Setup icon. NOTES

28

User System Setup (cont’d)
ICON ACTION 3. Press the USER SETUP icon. 4. Press the ADD USER icon and enter your Authorized Code. 5. Press the box next to Enter User Name. 6. Type in the user name (max. 6 characters; no spaces between characters) and press the OK icon. 7. Press the box next to User Number and enter an “available” (3-digit) user number; press the OK icon. 8. Press the box next to Enter User Code, enter the 4-digit User Code for this user and press the OK icon. 9. Press the box next to RF Button Zone (if used); enter the 3-digit RF Button Zone for this user. 10. Press the Save icon. NOTES
Use the Data Entry Keyboard to enter all required information. Enter the user name (6 characters max.; no spaces between characters) and press the GO icon. • Press the Up Arrow key to switch to capital letters • Press the X key to delete • Press the ABC/.?123 key to switch between numerals and symbols/characters. • Press GO to return to the “Add User” screen. For available user numbers, refer to the control panel instructions. If assigning this user to wireless key, enter one of the zone numbers of the keyfob (the wireless key must be programmed first before it can be assigned to a user).

How to Add an Existing User to a Second Keypad

After adding a user to the first keypad, the same user can be added to a second keypad. From the second keypad go to “User Setup” and enter the same user name and same user code (refer to “How to Add a User” above). The second keypad will automatically update the user information. Press Save.

How to Delete a User

Delete a User as follows: ICON ACTION 1. Select the User you want to delete. 2. Press the DELETE USER icon. 3. Enter your Authorized Code. 4. Press the appropriate icon.

NOTES
Three selections are available: add a user, edit a user, or delete a user. The Confirm Delete screen is displayed.

How to Edit a User
Note: You cannot edit a User name or User number. To modify a User name or User number, you must delete the User and re-enter the User. Edit a User as follows: ICON ACTION NOTES 1. Press the EDIT USER icon. Three selections are available: add a user, edit a user, or delete a user. 2. Enter your Authorized Code. 3. Select the options needed for this user and press Save.

29

User System Setup (cont’d)
You can set the time and date from the Set Time & Date screen. When the time is set it is stored in the keypad and sent to the control panel when you press Apply and answer Yes to the following prompt. Additionally, when using the keypad, the panel may download its time into the keypad periodically after the clock is set (for Vista residential and newer commercial panels such as Vista 128BPT). If the Get Time icon is pressed, the keypad downloads the time and date from the control panel and exits the Set Time & Date screen. Note: This icon appear with all commercial panels. appears with residential panels and may not

Time/Date Setup

Setting Daylight Savings Time
To set the daylight savings time, from the "Home" screen do the following: ICON ACTION 1. Press Setup and the System Setup icon. 2. Press the Time/Date Setup icon and enter your Authorized Code. 3. Press the DST icon if you want daylight savings time to affect your system clock. 4. Set the “Start DST” time and then the “End DST” time by pressing the Month, Weekend and Hour that you want DST to start. 5. APPLY saves the settings. NOTES

If DST On (Daylight Savings Time) is selected, the keypad adjusts for Daylight Savings time at the month, week and time chosen. Make sure "DST" On" is checked to enable this feature.

Setting Current Time and Date

To set the current time, do the following: ICON ACTION 1. Press the Time/Date Setup icon; enter your Authorized Code. 2. Press the Month "arrow", and select the current month. 3. Press the Year that is being displayed and enter the current year. 4. Press the Hour that is being displayed and enter the current hour. 5. Press the Minutes that is being displayed and enter the current minute.

NOTES
After each selection the window closes automatically and the selection is displayed. The selected date is highlighted on the screen. Select if you want a 12-hour or 24-hour format for your time display by pressing the circle to the left of the 12 Hour display.

30

User System Setup (cont’d)
ICON ACTION 6. Select AM or PM. (Each depression switches the AM/PM display). 7. Press the MMDDYY “arrow”, and select a format for which you want the year to be displayed. 8. Press Apply. NOTES
A confirmation screen displays: Time Setting Confirmation Set time on the security system as well? Yes or No Yes saves the time changes in your security system. No saves the changes to the keypad only. Note: A Yes response is recommended.

System Information
ICON

To view the current software/firmware version installed on your system, do the following: ACTION 1. From the "Home" screen, press the Setup icon. 2. Press the System Info icon. NOTES
The Interface Name, Host Name, MAC Address, IP Address, Broadcast Address, and NetMask are also displayed.

Keypad Reset

To access Keypad Reset do the following: ICON ACTION 1. From the "Home" screen, press Setup and the System Setup icon. 2. Press the Advanced Setup icon. 3. Enter your Authorized Code. 4. Press the Keypad Reset icon.

NOTES
When the Keypad Reset icon is pressed, the message is displayed: Confirmation Are you sure you want to reset? Select Yes or No.

The Advanced Setup screen allows access to Keypad Reset, Keypad Test, Night Setup and Output Setup menus. A series of diagnostic tests are provided that allows verification of correct operation of the keypad and its connections to the security system. There are a total of five diagnostic tests; LCD Display Test, Audio Test, LED Test, Calibration Test, and Z-Wave Test.

Advanced Setup
Keypad Test

Performing Diagnostic Tests

Select any diagnostic test from the “Diagnostics” screen by pressing its associated Test icon. All or any individual test may be run when you access the “Diagnostics” screen; however, each test must be performed one at a time. At any time when a test is not being performed, you can press: • back to return to the previous screen, or • home to return to your home page. Once the Diagnostics screen is exited, subsequent entry to this screen displays all test options as "Not Performed."

31

User System Setup (cont’d)
LCD Display Test
Perform the LCD Display Test as follows: ICON ACTION 1. Press the Advanced Setup icon. 2. If applicable, enter your Authorized Code. 3. Press the Keypad Test icon. 4. Press the LCD Display Test icon; a series of screens appear. After each type of display, you are asked if the display was proper.
If the response to all questions is yes, the LCD Display Test message area of the Diagnostics screen displays “Passed”.

NOTES
The Emergency screen cannot be accessed while running the LCD Display Test.

Audio Test
Perform the Audio Test as follows: ICON ACTION 1. Press the Audio Test icon; "Testing.." is displayed while beeps sound from the speaker.
At the conclusion of the test, a pop-up "Confirmation Window" is displayed with the question "Did you hear Beeping?"

NOTES
When you press Yes, "Passed" is displayed in the test status column on the "Diagnostics" screen. When you press No, "Failed" is displayed in the test status column on the "Diagnostics" screen.

LED Test

Perform the LED Test as follows: ICON ACTION 1. Press the LED Test icon; "Testing.." is displayed while the 3 LEDs light sequentially, top to bottom (red, green, yellow), 5 times.

NOTES
At the conclusion of the test, a pop-up "Confirmation Window" is displayed with the question "Did you see chasing LED pattern?" If you press Yes, "Passed" is displayed in the test status column on the "Diagnostics" screen. If you press No, "Failed" is displayed in the test status column on the "Diagnostics" screen.

32

User System Setup (cont’d)
Calibration Test
ICON If the Touch Screen requires recalibration, do the following: ACTION 1. Select the Calibration icon and using a stylus, follow the screen directions by pressing a series of crosshairs (+) and boxes (J) on the screen until done. J 2. If the test was successful, press OK; the screen returns to the Keypad Test screen. NOTES
A pop-up message displays: Touch screen calibration Touch crosshair to calibrate If the Calibration test was successful, a confirmation screen appears stating: “Congratulations Calibration Success” If the test was unsuccessful, an error message appears stating: “Calibration failed, do you want to retry?” Yes or No.

Z-Wave Test

This procedure is for Z-Wave test purposes only. Role shifting is the process of shifting primary and secondary keypads (controllers). The secondary controller becomes the primary controller with the ability to enroll Z-Wave devices. This is useful when the primary controller is in a fixed location and the Z-wave device is not easily accessible (but within Z-Wave range). To perform the role shifting Z-Wave Test, do the following: ICON ACTION NOTES Note: The status of the controller can only be 1. Press the Advanced Setup icon. changed from Primary to Secondary controller 2. Enter your Authorized Code.
when no devices are enrolled. Use the delete device or reset controller function to remove enrolled devices. Select from two main categories of tests: • Z-Wave Role Shifting: Primary to Secondary and Secondary to Primary. • Z-Wave Basic Command: Set On or Off.

3. Press the Keypad Test icon. 4. With the status of the controller in the “P” (Primary) state, press the Z-Wave Primary Controller Shift to Secondary icon. 5. To shift the primary controller role to a handheld controller, follow the handheld controller manufacturer’s instructions. When the pop-up message disappears and controllers have shifted successfully, ZWave devices can be enrolled from this controller. 6. Shift the Tuxedo Touch back to the primary controller after enrolling Z-wave devices. First, initiate the role shift on the handheld controller from primary to secondary referring to manufacturer’s instructions. Then, press the Z-Wave Secondary Controller Shift to Primary icon on the keypad.

A pop-up window is displayed with the following: “Role Shift is in progress, please wait ... This Z-Wave controller shift function is for evaluation only now. This primary controller is shifting to the secondary. The Shift is completed when the pop-up window disappears. Note: The Z-Wave Primary Controller Shift to Secondary icon is inactive when the Tuxedo Touch keypad becomes the secondary controller.

33

User System Setup (cont’d)
ICON ACTION 7. Select the Z-Wave Basic Command Set On icon to turn On all lamp modules, dimmer On/Off switches and receptacles. 8. Select the Z-Wave Basic Command Set Off icon to turn Off all lamp modules, dimmer On/Off switches and receptacles. NOTES
Note: This command does not control door locks or any other security enabled devices. Note: This test may cause lights and thermostat settings to change." Note: This test may cause lights and thermostat settings to change."

NIGHT Setup Function

The NIGHT function can be set to arm the system in one of five arming modes: • Away - Arms all zones with entry delay. • Stay - Arms perimeter zones with entry delay. • Instant - Arms perimeter zones without entry delay. • Night (Residential Panels Only) – Arms all perimeter zones plus all zones listed in Zone List 5. • Maximum - Arms all zones without entry delay. Not to be used for ANSI/SIA CP-01 installations. To set the NIGHT function, do the following: ICON ACTION 1. Press the System Setup and Advanced Setup icon. 2. Enter your Authorized Code, if required. 3. Press the Night Setup icon. 4. Select the arming mode to be activated when NIGHT is selected on the "Arming" screen. NOTES

Apply accepts the setting. Back cancels your selection.

Output Setup Function
The Output Setup screen displays Output selections. There are a maximum of 18 outputs that can be enabled or disabled. To set the Output Setup function, do the following: ICON ACTION NOTES 1. Press the System Setup and Advanced This is a local setting for the graphic keypad. If user has the maximum number of keypads on Setup icon. the system, and wants to disable the same 2. Enter your Authorized Code, if required. output for all, each keypad needs to be set 3. Press the Output Setup icon. individually. 4. Select the outputs to display or not A confirmation window is displayed stating: display on the Output screen and press “Information Settings saved” Apply.
Press OK to save the setting

Output Setup Icons
If the Back icon is pressed, a confirmation window appears stating: “Output Settings changed. Do you want to save new settings?” Select Yes or No.

Apply

OK

Back

Home

34

Automation
The Automation feature allows access to Group Setup, Scene Setup, Z-Wave Setup and Output List. WARNING: Automation is intended for lifestyle convenience. Do not use automation for life safety and property protection. • Automation functionality is supplementary only and has not been evaluated by UL. UL • Z-Wave applications have not been evaluated by UL.

Enroll/Adding Z-Wave Devices

Before a device will work in the home control network, it must be “Enrolled” (added) into the network. Each device must be installed according to the manufacturer’s instructions. View the “Programming of Z-Wave Devices” training video and follow the instructions below to add and control devices in a home control network. UL Access control functionality has not been evaluated by UL and may not be used in UL Listed applications.

Enroll/Add a Light, Switch or Outlet Module
To enroll a Z-Wave Light, Switch or Outlet module, do the following: ICON ACTION 1. At the Tuxedo Touch Keypad: a) Press the Automation icon from the “Home” screen and then press the Z-Wave Setup icon to display the “Z-Wave Device Management” screen. b) Press the Z-Wave Enroll/Add icon. 2. At the device Module: a) Press the Function Key on the device. NOTES
Note: Z-Wave light modules may vary; follow the instructions in the User Guide for your specific device to enroll properly. • If a dimmer module was added, an On/Off button and a slide bar (to control the dimmer) are displayed. • If an on/off light, appliance, switch or outlet module was added, an On/Off button (to control the device) is displayed. The keypad displays a series of messages: “Start add device. Please press function key on device” “Adding Controller Unit” “Adding Slave Unit” “Device added successfully”

Z-Wave Device Management Icons

Enroll/Add

Remove/ Delete

Abort

Remove Failed

Edit

Reset Default

Router

Security

Link

35

Automation (cont’d)
Enroll a Door Lock
Assemble the Z-Wave door lock. NOTE: Be sure the door lock orientation/handedness is correct. Refer to the Door Lock’s Instruction Guide and connect necessary cables, then install batteries. Enroll the door lock within 5 feet of the keypad refer to the Door Lock’s Instruction Guide for enrollment procedure. NOTE: Program the user code in the control panel prior to programming that user code into the door lock. User Codes must be 4-digits. Enroll a door lock device as follows: ICON ACTION 1. At the Tuxedo Touch Keypad: a) Press the Automation icon from the “Home” screen and then press the Z-Wave Setup icon to display the “Z-Wave Device Management” screen. b) Press the Z-Wave Enroll/Add icon. 2. At the door lock: a) Program the selected user code from the panel; refer to Door Lock User Guide. NOTES
Note: Door lock devices may vary; follow the instructions in the Users Guide for your specific door lock to enroll properly and to program a new user code. The keypad displays a series of messages: “Please press * function key on device” “Adding to Security Network” “Device added successfully” * Enrollment procedure may vary depending on the door lock device. Refer to the door lock instructions for enrollment procedure. Note: If software is upgraded on the Tuxedo Touch keypad, enroll the door lock again and reset the user code in the door lock.

Enroll a Honeywell Thermostat

Install a Honeywell Thermostat according to the manufactures instructions. Device should be mounted in the final location and tested before adding it to the system. To enroll a Honeywell Thermostat into a Z-Wave network, do the following: ICON ACTION NOTES 1. At the Tuxedo Touch Keypad: Note: If installing another brand of thermostat, a) Press the Automation icon from the follow the instructions in the Users Guide for that specific thermostat to enroll properly. “Home” screen and then press the Some thermostats do not update temperature Z-Wave Setup icon to display the “Z-Wave Device Management” screen. status automatically (i.e., Wayne Dalton). IMPORTANT: Honeywell is not responsible for b) Press the Z-Wave Enroll/Add icon. property damages due to improper setting of the 2. At the Z-Wave thermostat: a) Select Thermostat; set the Time and thermostat modes. The keypad displays a series of messages: Date. “Please press *function key on device” b) Follow the instructions in the “Adding Controller Unit” thermostat Installation Guide for “Adding Slave Unit” “Z-Wave inclusion”. “Device added successfully” c) To complete inclusion, press Done. * If not using a Honeywell thermostat, enrollment d) Press Exit on the thermostat to procedure may vary. Refer to the thermostat instructions for enrollment procedure. return to normal operation. 3. At the Tuxedo Touch Keypad: a) To verify activation, press the Back Press the Refresh icon; the device is displayed. icon and wait 30 seconds.

36

Automation (cont’d)
Editing Z-Wave Device Names
Edit a Device Module Name
ICON To edit a device name, do the following: ACTION 1. At the Tuxedo Touch Keypad: a) Press the Automation icon from the “Home” screen and press the Z-Wave Setup icon to display the “Z-Wave Device Management” screen. b) Highlight the device name and press the Z-Wave Edit icon. c) On the “Data Entry” keyboard, press Clear and enter a new name; press GO. NOTES
Enter the new device name by entering it on the data entry keyboard. • Press the Up Arrow key to switch to capital letters • Press the X key to delete • Press the ABC/.?123 key to switch between numerals and symbols/characters. • Press GO to return to the previous screen.

Remove/Delete Z-Wave Devices

Remove a Light, Outlet, or Switch Module

To remove a device from the Z-Wave network, do the following: ICON ACTION NOTES 1. At the Tuxedo Touch Keypad: Z-Wave Remove/Delete -clears the node from the keypad and resets device to the default a) Press the Automation icon from the setting. “Home” screen and then press the Z-Wave Setup icon to display the “Z-Wave Device Management” screen. Notes: b) Highlight the device to remove and • If the device is not removed, refer to the “Zpress the Z-Wave Remove/Delete icon. Wave Troubleshooting” section. • To remove a defective device, refer to the Z2. At the device module: Wave Troubleshooting section. a) Press the Function Key to remove the device from the keypad.

Remove a Door Lock Device

To remove a door lock module from the Z-Wave network, do the following: ICON ACTION 1. At the Tuxedo Touch Keypad: a) Press the Automation icon and then press the Z-Wave Setup icon to display the “Z-Wave Device Management” screen. b) Highlight the device to remove and press the Z-Wave Remove/Delete icon. 2. At the door lock: a) Press the Function Key to remove the device from the keypad.

NOTES

Z-Wave Remove/Delete-clears the node from the keypad and resets device to the default setting. Notes: • If the device is not removed, refer to the “ZWave Troubleshooting” section. • When removing the door lock, the user code associated with the door lock will remain in the system. If needed refer to the panel Installation Instructions on how to remove this user code. • To remove a defective device, refer to the “ZWave Troubleshooting” section.

37

Automation (cont’d)
Remove a Honeywell Thermostat
To remove a Honeywell Thermostat from the Z-Wave network, do the following: ICON ACTION NOTES 1. At the Tuxedo Touch Keypad: Note: Honeywell is not responsible for property a) Press the Automation icon from the damages due to improper setting of the thermostat modes. “Home” screen and then press the Z-Wave Remove/Delete -clears the node from Z-Wave Setup icon to display the the keypad and resets device to the default “Z-Wave Device Management” setting. screen. b) Highlight the thermostat and press the Z-Wave Remove/Delete icon. 2. At the thermostat: Notes: a) Follow the instructions in the • If the device is not removed, refer to the “Z-Wave Troubleshooting” section. thermostat Installation Guide under “Installer setup” to “Remove a Z• To remove a defective device, refer to the “Z-Wave Troubleshooting” section. Wave Network Connection”. b) Once the exclusion process is complete, press Done and the thermostat is removed.

Remove All Z-Wave Devices
ICON ACTION 1. At the Tuxedo Touch Keypad: a) Press the Automation icon from the “Home” screen and then press the Z-Wave Setup icon to display the “ZWave Device Management” screen. b) Press the Z-Wave Reset icon to delete all devices from the controller. c) Select Yes or No. NOTES

The message is displayed: Window Warning This Z-WAVE controller is about to be factory defaulted and will lose all devices in the enrolled list. All Z-WAVE devices must be reenrolled after this reset. Yes or No

Abort a Z-Wave Action
ICON ACTION 1. At the Tuxedo Touch Keypad: a) Press the Automation icon from the “Home” screen and then press the ZWave Setup icon to display the “ZWave Device Management” screen. b) Press the Z-Wave Abort Operation icon to abort that process. NOTES
If inadvertently a wrong process is selected, (i.e., add, delete, or remove failed device) press the Z-Wave Abort icon to abort that process.

38

Automation (cont’d)
Output List
To access the Output List, from the “Home” screen, do the following: ICON ACTION 1. Press the Automation and Output icons. 2. Enter your Authorized Code. 3. Use the OFF or ON button to control outputs.

NOTES

Scene Setup

The Scene feature is used to control a single device, or multiple devices based on pre-set “Conditions,” “Triggers,” and “Actions”. When a trigger/condition occurs, the action is executed. View the “Customizable Automation Scene” training video and then do the following: ICON ACTION 1. At the Tuxedo Touch Keypad: a) Press the Automation icon and then press the Scene Setup icon to display the “Scene Management” screen. b) Press the Add icon. c) Press the Scene Name box, enter a Scene Name and press OK. d) Select a “Condition,” “Trigger,” and “Action” that you want to occur for this Scene. See example below. After each selection press Save!! ! NOTES
INFORMATION: Scenes must have at least a trigger and 1 action to work. Use the Data Entry Keyboard to enter all required information. • Press the Up Arrow key to switch to capital letters • Press the X key to delete • Press the ABC/.?123 key to switch between numerals and symbols/characters. • Press GO to return to precious screen. Press Delete to cancel, or Edit to change your selections.

Scene Icons

Condition/Trigger/Action Icons

ADD

DELETE

EDIT

LOG

Add

Edit

Delete

Save

Scene Rules • Triggers and Conditions include: Time setting, Security mode, Thermostat setting, and Door status. • Actions include: Security mode, Lights on/off, Thermostat setting, and Door Lock status. • Each Trigger event can have up to 3 Actions. • A Trigger event and Condition cannot be the same (i.e., if setting a Trigger event for SECURITY, you cannot set a SECURITY Condition). • A total of 10 Scenes can be created. Note: Determine if you need a Condition. The Condition is a ‘condition’ set to occur prior to a trigger event. See example below. Example: Turn the lights on, when the system is disarmed, only at night. (Condition) … “only at Night” ...Set the TIME condition (enter the Start Time and Duration). (Trigger) ……when the “system is Disarmed” …Set the Trigger to SECURITY: System Disarm. (Action) … Turn the “lights ON” … … Set the Action to LIGHT: ON.

39

Automation (cont’d)
Options for adding a Condition (if needed) – After each selection press SAVE!!! In the “Condition” box, press the Add icon. To set the time, press the TIME button: “Set the occurrence” to Repeated, or Once. If “Repeated” was selected, choose the desired days of the week; if ONCE was selected Enter Date. To set the security mode, press the SECURITY button and select: DISARM, AWAY, STAY, NIGHT. To set the thermostat settings, press the THERMOSTAT button and select a Thermostat Device from the drop down menu. Use the ABOVE and BELOW buttons to increase/decrease the temperature or press the Temperature Value box and enter 2 digits for the desired temperature. Note: Test thermostats first to ensure proper function in the Scene feature. To set the door lock status, press the DOOR button and select a Door Device from the drop-down menu (see notes below). Select LOCKED or UNLOCKED. Options for adding a Trigger – After each selection press SAVE!!! In the “Trigger” box, press the Add icon. To set the time, press the TIME button and “Set the occurrence” to Repeated, or Once. If “Repeated” was selected, choose the desired days of the week; If ONCE was selected, Enter Date. To set a security mode, press the SECURITY button and select: DISARM, AWAY, STAY, NIGHT (for residential panels only). To set the thermostat settings, press the THERMOSTAT button to select the Thermostat Devices from the drop down menu. Use the ABOVE and BELOW button to increase/decrease the temperature range or press the Temperature Value box and enter 2 digits for the desired temperature. Note: Test thermostats first to ensure proper function in the “Scene” feature. To set the door lock status, press the DOOR button to select a Door Device from the drop-down menu (see notes below). Select LOCKED, UNLOCKED or CODE UNLOCKED. Options for adding an Action – After each selection press SAVE!!! In the “Action” box, press the Add icon. To set the security mode, press the SECURITY button and select: DISARM, AWAY, STAY, NIGHT. Enter User Code, if required. To set the light on/off, press the LIGHT button and select a Light Device from the drop down menu; set the action to ON or OFF. To set the thermostat settings, press the THERMOSTAT button and select a Thermostat Device from the drop-down menu. Press the Set Mode button to set the Action to “Off”, “Heat”, or “Cool”. Press the Set Energy button and select from “Normal” or “Saving” energy mode. Press the Set Point button and enter a set point value for “Heat Point” and “Cool Point”. Note: Test thermostats first to ensure proper function in the Scene feature. To set the door lock status, press the DOOR button and select a Door Device from the drop-down menu (see notes below). Set the action to LOCKS or UNLOCKS Notes: 1. Motorized door lock bolts physically lock and unlock when activated, but if the door lock installed is a non-motorized type, activation allows the door to be manually unlocked without a key. See “Compatible Devices” section for further information. 2. Some thermostats do not update temperature status automatically (i.e., Wayne Dalton). 3. When using a Kwikset Smartcode electronic deadbolt door lock (in a Scene that is programmed to trigger when unlocked) the Scene does not trigger if using a key; enter a user code.

40

Automation (cont’d)
Create a Group
Multiple Z-wave devices can function together in a group. Up to 50 groups can be created. Follow the procedure below to create a Group. ICON ACTION NOTES Group names (i.e., All, etc.) are displayed across 1. Press the Automation icon and then the top to the screen. press the Group Setup icon. 2. Press the Add icon and enter a “Group Use the Data Entry Keyboard to enter all required information. Name” on the “Data Entry” keyboard. • Press the Up Arrow key to switch to upper case 3. Press GO. letters 4. Highlight the device(s) from the list • Press the X key to delete that you want to add to this Group • Press the ABC/.?123 key to switch between numerals and symbols/characters. and press the Save icon.
• Press GO to return to the previous screen.

Group Setup Icons
If settings were changed, a pop-up window displays: Settings saved. Select OK to save. Delete Edit Add Save

Setting a Secondary Keypad (Controller)
After all Z-Wave devices have been enrolled into the Primary Keypad (Controller), the device information on the Primary Controller can be downloaded to a Secondary Keypad (Controller). Keep the controllers within 10 feet of each other, apply power to the Secondary Controller and do the following: ICON ACTION 1. On the Primary Controller: a) Press the Automation icon from the “Home” screen and then press the Z-Wave Setup icon to display the “ZWave Device Management” screen. 2. At the Secondary Controller: a) Remove any Z-Wave devices that have been added. b) Press the Z-Wave Primary icon (located in the lower right side of the screen). c) Select Yes to change this keypad to a Secondary Controller. 3. At the Primary Controller: a) Press the Add icon. 4. At the Secondary Controller: a) Press the Add icon. 5. To edit information, use the Z-Wave Edit icon. NOTES

When the Primary Controller icon is pressed, the message is displayed: “Please remove all Z-wave devices from network first”

The message is displayed: “Scanning for Devices” The message is displayed: “Updating Devices. Please Wait” When the device information from the Primary Controller is downloaded to the Secondary Controller, the Secondary Controller displays: “Controller Add Success” The Primary Controller displays: “Device Added Successfully”

41

Automation (cont’d)
Updating Keypads (Controllers) with New or Removed devices
When devices are added or removed from the Z-Wave network, the device information needs to be updated in the Secondary Keypad (Controller). From the Primary controller, do the following:
ICON ACTION 1. Press Add on Primary controller. 2. Press Add on Secondary controller. NOTES
The controller scans for device changes. The message is displayed: “Devices added Successfully”

Removing a Secondary Keypad (Controller)

To remove the Secondary Keypad (Controller), do the following: ICON ACTION NOTES 1. At the Primary Controller keypad: Both keypads will display, “Device Removed” and the a) Press Delete. Secondary Controller keypad will revert back to the 2. At the Secondary Controller keypad: Primary Controller. b) Press Delete.

Z-Wave Troubleshooting
PROBLEM Cannot add new device. SOLUTION Make sure Z-Wave device is within range of the keypad. You may need to move device closer to the keypad. Refer to the ZWave device Instruction Guide for proper range. 1. At the Tuxedo Touch Keypad: a) Press the Automation icon from the “Home” screen and then press the Z-Wave Setup icon to display the “Z-Wave Device Management” screen. b) If the device does not appear on the screen, press the ZWave Remove/Delete icon. 2. At the Z-Wave device, press the Function Key. The screen will display a message “Device Removed”. 3. At the Tuxedo Touch Keypad: a) Enroll device again. When deleting a device, if the selected device remains on the screen, highlight the device name and press the Z-Wave Removed Failed icon.

Device is within proper range but still will not enroll.

Highlighted device will not delete.

42

Automation (cont’d)
Compatible Devices
Z-Wave devices may vary; follow the instructions in the Users Guide for your specific device when adding and deleting devices into the Z-Wave network.
Refer to the table below for some of the compatible devices. Door Locks Yale Real Living Push Button Lever Lock Yale Real Living Touchscreen Lever Lock Yale Real Living Push Button Deadbolt Lock Yale Real Living Touchscreen Deadbolt Lock Schalge Link Deadbolt Lock Schlage Link Lever Lock Kwikset Smartcode Lever lock Kwikset Smartcode Deadbolt Lock Thermostats Honeywell ECC Wayne Dalton Zwave Thermostat Trane Zwave Thermostat Appliance HomeManageable Appliance Module Wayne Dalton Small Appliance Module GE Wireless Lighting Control Plug in Appliance Module Lights Leviton/ViziaRF+ Switches Leviton/ViziaRF+ Dimmers Leviton/ViziaRF+ Plug in Modules GE Wireless Lighting Control Dimmers GE Wireless Lighting Control Switches GE Wireless Lighting Control Plug in Lamp Modules Not all Z-wave devices have been tested and some features may produce unpredictable results.

43

Important Notes
For additional troubleshooting procedures, refer to the Control Panel Installation Guide.

General Notes
• You may check to see whether the Chime Mode is ON or OFF by viewing the keypad Operating Modes screen as described in “Operating Modes” in Section 5 of the keypad Installation and Setup Guide. • Note that some displays on the keypad may not have enough space to display the whole name of a partition. When this occurs, the display shows as many characters as possible starting at the beginning of the partition name. We recommend that the partition name be kept to a maximum of 7 characters to ensure the “H” which indicates the home partition may be seen. • “Exit Error” and “Auto Arm Alert, Please Leave Now” messages are not displayed by the keypad. • When the system has 6150Vs or 6160Vs, and 6271Vs attached, the Additional Console setting in the 6150Vs (displayed as A on the 6150V) must be set to 1 and the Additional Console setting in the 6160Vs must be set to Yes.

Commercial System Notes
• If the Aux Relay function is set for alarm silenced by User Code + # + 67, this command may only be entered in the console emulation mode. • Do not use the common lobby logic function. • If fields 2*22 (Display Fire Alarms of other Partitions), 2*23 (Display Burg & Panic of other Partitions), or 2*24 (Display Troubles of other Partitions) are enabled, the zones that created the conditions cannot be viewed. You must go to that zone's home partition to view. • If field 1*11 (Zone Bypass After Disarm) is enabled, you must use the keypad’s Console Emulation Mode and the commands “Code” + “64” (unbypass all) or “Code” + “6” + “Zone Number” (unbypass zone) to remove zone bypasses. • The First to Alarm Display Lock feature (field 1*10) is not supported by the keypad. • RF Low Battery messages are not supported by the keypad except in the Show Zones screen where a Battery Icon is displayed for the zone with the low battery.

Residential System Notes
• If the Clean Me option is set, when the maintenance signal is received a “Fire Maintenance” message and the Display Faults icon is shown. However, if you display the faults, zone 1 is not shown as a faulted zone. • If RF Jam Reports are selected and RF Jam is detected, the User Authorization screen displays “Trouble ZN100 RF Receiver”. If you enter the console emulation mode, the display shows “Check 90 RF Receiver Jam”. • Do not use the Custom Word reminder feature. • Users added to the system using the keypad graphic user screen must be deleted from the keypad using the graphic screen as well. Deleting users from the panel by any other means (alpha keypad, console emulation mode, or Compass downloader) does not automatically delete them from the keypad.

User Related Notes

44

Important Notes (Cont’d)
• If the panel has exit tones enabled and you arm the system in the Away mode, the keypad beeps continuously throughout the exit period. Use the console emulation mode for the following functions: - Programming more than 10 system users. - Programming the Pager report option for users of residential control panels (e.g., VISTA-15P and VISTA-20P). - Special Function Key operations (such as macros or single-button paging). - End-User Scheduling. - To check for an “Alarm Cancelled” message (on commercial panels only) if this feature has been enabled in the system. Wireless Range This device complies with the Z-Wave® standard of open-air, line of sight transmission distances of 100 feet. Actual performance in a home depends on the number of walls between the controller and the destination device, the type of construction and the number of Z-Wave enabled devices installed in the control network. Please Note: Z-Wave home control networks are designed to work properly alongside wireless security sensors, Wi-Fi, Bluetooth and other wireless devices. Some 900 MHz wireless devices such as baby cams, wireless video devices and older cordless phones may cause interference and limit Z-Wave functionality. Things to consider regarding RF range: - Each wall or obstacle (such as refrigerator, big screen TV, etc.) between the remote and the destination device will reduce the maximum range of 100 feet by approximately 25-30%. - Brick, tile or concrete walls block more of the RF signal than walls made of wooden studs and drywall. - Wall mounted Z-Wave devices installed in metal junction boxes will suffer a significant loss of range (approximately 20%) since the metal box blocks a large part of the RF signal. WARNING: NOT FOR USE WITH MEDICAL OR LIFE SUPPORT EQUIPMENT! Z-Wave enabled devices should never be used to supply power to, or control the On/Off status or medical and /or life support equipment. Controlling Devices: The features and functions that can be controlled vary by manufacturer and you will need to review the user manual that was provided to determine capabilities of each device. IMPORTANT: Honeywell is not responsible for property damages due to improper setting of the thermostat modes.

45

Important Notes (Cont’d)
Effects of Home Construction on Wireless Range between Z-Wave Enabled Devices Note: The distances shown in the table below are typical examples. Actual performance in your home will vary. From the Remote (or repeating Z-Wave module) to the destination device: Type of Construction Number of Walls Wood Frame with Drywall Brick, Tile or Concrete or Obstacles Plastic J-Boxes* Metal J-Boxes Plastic J-Boxes* Metal J-Boxes 0** 100 ft 80 ft 100 ft 80 ft 1 70 ft 56 ft 60 ft 48 ft 2 49 ft 39 ft 36 ft 29 ft 3 34 ft 27 ft 21 ft 17 ft
* For Plug-in modules or in-wall devices installed in plastic junction boxes. **Line of sight / no obstructions. Z-Wave devices are identified by the Z-Wave logo and can be purchased from your local retailer. ® Z-Wave is a registered trademark Sigma Designs, Inc. and/or its subsidiaries.

UL

CO annunciation has not been investigated by UL and may not be used for UL installations.

46

FEDERAL COMMUNICATIONS COMMISSION STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. FCC CLASS B STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • If using an indoor antenna, have a quality outdoor antenna installed. • Reorient the receiving antenna until interference is reduced or eliminated. • Move the radio or television receiver away from the receiver/control. • Move the antenna leads away from any wire runs to the receiver/control. • Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. • Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les interferences causant une reception indésirable. RF EXPOSURE WARNING The Tuxedo Touch WIFI must be installed to provide a separation distance of at least 7.8 in. (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.

For the latest warranty information, please go to:

www.honeywell.com/security/hsc/resources/wa

2 Corporate Center Drive, Suite 100 P.O. Box 9040 Melville, NY 11747 Copyright © 2012 Honeywell International Inc. www.honeywell.com/security

Ê800-103006Š
800-10300 11/11 Rev. B

For Online Support visit: http://www.security.honeywell.com/hsc/resourses/MyWebTech