2GIG Edge - Quick Start Install Guide - Dated 2021 Rev. B

1
Nortek Security & Control LLC
Standard-Style Duplex Receptacle
Decora-Style Duplex Receptacle
8.
Install Retaining Wall Bracket & Connect the AC Power Supply
For compliance with ANSI/NFPA 70: National Electric Code in the United States, you
must install the power supply retaining bracket (not required in Canada).
2GIG
®
Security & Smart Home System
2GIG EDGE Installer Quick Start Guide
10029907 Rev-B | 2GIG-EDG-NA | EDGE Panel
Barrel
Connector
Back Plate
Attached to Wall
1
2
3
4
5
6
7
8
9
10
11
12
13
14
GND
AUX+
GND
Bell +
Bell –
Zone 1
Zone 2
GND
DC IN
DC IN +
DC IN –
OCL 1
OCL 2
TX
RX
5.
Connect Power (Barrel Connector)
The Barrel connector is an alternate method for connecting the AC power supply for
the EDGE Panel.
WARNING!!
Do NOT plug the power supply into the outlet at this time.
4.
Connect the Power Wires (Terminal Block)
Locate a wall outlet for the plug-in power supply, but do NOT connect the power
supply to the outlet at this time.
IMPORTANT:
Never connect the plug-in power supply to a switch-controlled outlet. Do not
over-tighten the terminal block’s contact screws.
STANDARD
DECORA
STANDARD
DECORA
Standard Style – Center Fastener
Decora Style – Center Fastener
Secure with Fastener
7.
Hang the EDGE Panel
Place the backplate over the lower lip on the back of the chassis, and flip the EDGE
panel downward and push until it clicks into place.
Battery Power Terminal
I
ntroductIon
This quick start guide introduces 2GIG alarm dealers and professional installers to
2GIG EDGE panel hardware installation and the
Installer Toolbox
. It describes the
process of programming zones, keyfobs, and keypads for the EDGE Panel and how to
add and remove Z-Wave
®
devices from the network. To get started, navigate to the
Installer Toolbox menu.

EdGE P
anEl
I
nstallatIon
Choose the Location for the 2GIG EDGE Panel’s Backplate
Before mounting the backplate, choose a location. Work with the end user to
determine the best location. Always choose an indoor location protected from
temperature extremes.

Recommended Tools and Equipment
To install the system, these tools and equipment are recommended:

➣
2-Conductor Power Wire (if connecting power supply to the panel’s terminal block)

➣
Drywall Saw (or equivalent)

➣
Ladder

➣
Screwdrivers

➣
Staple Gun

➣
Wire Stripper
Choose the Wall Location
To choose a wall location:

➣
Always choose a location that is above ground and centrally located. Do NOT install
the Panel below ground level, because wireless range may be impaired.

➣
Do NOT connect the Panel to a light switch-controlled outlet.

➣
Avoid choosing a location that can be easily viewed from doors or windows.

➣
Avoid choosing a location that is within reach of small children.

➣
Avoid choosing a location in direct sunlight.
NOTE:
If necessary, the Panel can be mounted on a stand that can be placed on a
flat surface, such as desk or counter using the 2GIG Desktop Kit. However, this option
may affect compliance with state or regional codes. For 2GIG Desktop Kit installation
instructions, refer to the 2GIG EDGE Installation Manual.

External Attic Mount Antenna Installation (Optional)
If you will be installing the optional External Attic Mount Antenna, refer to the 2GIG
EDGE Installation Guide.

1.
Align Backplate to Mark Hole Locations
Create mounting holes, and cut a slot in the dry wall for the AC power cord and other
electrical wiring (if needed).
2.
Mount the Backplate to a Wall
Use the four (4) wall anchors and screws (supplied).
NOTE:
The Wall Anchor is the wall tamper and MUST be anchored to work.
LEVEL
NOT LEVEL
Wall Tamper
Illustration displays both types of power connection:
Install the 2 - conductor power wires
or
Barrel Connector
3.
Hang the Panel for Wiring (optional)
Attach the panel’s third-hand hanging strap to the hook at the bottom of the backplate
for easy access during wiring.
Edge Panel (upside down)
Back Plate
Hanger
6.
Connect the Backup Battery
Align pins, then carefully insert the battery cable.
Indicates Mounting Hole 2
Nortek Security & Control LLC
I
nstallEr
t
oolbox

The Installer Toolbox is password-protected. To use this feature, you must enter an Installer Code. The factory
default code is 1561.
NOTE:
When accessing the Toolbox for the first time the installer must read and acknowledge
the regulatory agreement.
To access the Installer Toolbox:
1.
Tap the
Settings
icon (
).
2.
Ta p
KEYPAD.

3.
Enter
1561
to gain access to the panel
settings, then tap
Installer Toolbox
.
4.
Scroll down then tap the
Installer
Toolbox
icon.

5.
Ta p
Panel Programming
to view
programming options (see below).

P
anEl
P
roGrammInG
– W
IrElEss
Z
onEs

Program up to 100 wireless zones per system. Tap
Wireless Zones

to view the Wireless Zones screen. To get started,
navigate to the Installer Toolbox, Tap Panel Programming, then tap the Wireless Zones option.
Setup a Wireless Zone
Left side of screen:
Select a Wireless Zone [#].
Right side of screen:
Ta p
EDIT ZONE
to program and
edit each zone setting.
P
anEl
P
roGrammInG
– b
uIlt
-I
n
Z
onEs



/ G
lass
b
rEak
You can program up to three (3) Built-In Zones per system. To get started, navigate to the
Installer Toolbox
.
Ta p
Panel Programming
, then tap the
Built-In Zones
option.
Selecting a Built-In Zone
Left side of screen:
Select a Wired Zone [#].
Right side of screen:
Ta p
EDIT ZONE
to program and
edit each zone setting.
Built-In Glass Break
This panel has a built-in glass break sensor that
monitors for breaking of glass in the close vicinity of the
panel when Alarm System is in Armed Away mode. Tap
EDIT ZONE
to Enable and program this feature.
P
anEl
P
roGrammInG
– k
Eyfobs

Program up to 32 keyfobs per system. To begin, navigate to the
Installer Toolbox
, then tap
Panel Programming

then Keyfobs.
Select a Keyfob
Left side of screen:
Select a Keyfob [#].
Ta p
EDIT KEYFOB
to program and edit keyfob settings.
P
anEl
P
roGrammInG
– k
EyP
ads

You can program up to eight (8) wireless keypads per system. To get started, navigate to the Installer Toolbox.
Then, tap Keypads. This reveals the Keypads screen.
Setup Keypad (#)
1.
Swipe up to move through the list of keypads.
2.
Tap to select one of the available keypads.
3.
Ta p
Edit Keypad
.
4.
Make sure the Keypad Used setting is highlighted.
5.
Under
Keypad Used
, choose
Enabled
or
Disabled
.
6.
Ta p
t
to move to the next option.
NOTE:
Refer to the full installation instructions detailed in
the EDGE Remote Keypad guide.
P
anEl
P
roGrammInG
– n
EtWork
s
EttInGs

Connect to Wireless Network
1.
Tap an available
Network Name
.
2.
Correctly enter the assigned network password to
connect.
3.
Ta p


to go back to the Network Settings menu.
Setup the Access Point
1.
Ta p
Network Settings
.
2.
Ta p
Access Poin
t.
3.
Enable Access Point:

➣
Optional:
Ta p (
) to enter a new SSID name

➣
Optional:
Ta p (
) to enter a new password

➣
Optional:
Ta p (
) IP address. The last two
octets of the Access Point can be changed to
customize the setup.
4.
If edits have been made, tap
SAVE SETTINGS
to save.
NOTE:
Make a note of SSID and Password for use in
WiFi setup of EDGE Remote Keypads and Cameras.
5.
Ta p


to go back to the Network Settings menu.
P
anEl
P
roGrammInG
– a
dvancEd
P
roGrammInG

Ta p
Installer Toolbox
, then tap
Panel Programming > Advanced Programming > System Configuration
.

System Configuration


Timers, Delays & Counts

Panel Configuration

Troubles

Reporting
1.
Highlight a question [Q### - (settings differ based on the
question)].
2.
Tap available options to adjust settings.
3.
Ta p


to move to the next question, or tap


to return to
the previous menu.
NOTE:
Ensure that the settings you program are in
compliance with all national, state, and local regulations.
NOTE:
For more in-depth information about the list of
questions available in the Panel Programming menu, refer
to the EDGE Installation & Programming Guide.
s
mart
H
omE
s
EttInGs

Add up to 232 Z-Wave devices to the network. After
adding or removing a device you should always
rediscover the network. Tap
Settings
, then
Smart Home
Settings
to view the Smart Home Settings menu.
For detailed information, refer to the
2GIG Smart Home
Manual
.
Add Device / Remove Device
Use these options to add or remove Smart Home
devices. On-screen instructions will guide you through
the process.
Rediscover Network
Tap this option, then tap
START
to rediscover the
Z-Wave network.
s
ystEm
t
Ests

After installing the system, sensors, and peripherals,
perform a walk test to ensure proper console
operations and to test wireless reception and signal
strength.
From the
Installer Toolbox
menu, then select
SYSTEM
TESTS
.
r
EstorE
d
Efaults

If at any time you want to restore the system’s settings to the factory defaults.
1.
Navigate to the
Installer Toolbox
.
2.
Tap the
Restore Defaults
icon.
3.
Tap to enable the
Restore
switch for the specific option(s).
4.
Ta p
RESTORE
.
t
EcHnIcal
s
uPPort
Nortek Security & Control LLC
5919 Sea Otter Place, Suite 100, Carlsbad, CA 92010 USA
Phone:
800-421-1587 •
Online:

www.nortekcontrol.com/support/
10029907 Rev-B
Copyright ©2021 Nortek Security & Control LLC. All Rights Reserved. U.S. Patent D727,857. Australian Patent No. 357098.
Additional Patents Pending.
The 2GIG, EDGE, GoControl, and Linear logos are registered trademarks of Nortek Security & Control LLC in the United States and/
or other countries. Other Nortek Security & Control trademarks may also appear in these materials. Other names or brands may be
claimed as the property of others. For more information, contact your 2GIG alarm dealer for pricing or visit
www.2gig.com
.