2GIG Edge Remote Keypad - Quick Start Guide - Dated 03-22-21 Rev. B

2GIG
®
EDGE Security & Smart Home System
2GIG-EDG-RK
| EDGE Remote Keypad
Proprietary & Confidential
Copyright © 2021 Nortek Security & Control LLC
Introduction
The Remote Keypad (2GIG-EDG-RK) is a wall-mounted, full-color, touch screen interface that
provides all of the same easy-to-use keypad functions available on the Control Panel. It is
designed for indoor use only and gives users the ability to arm and disarm the system, see the
status of sensor zones, and control Smart Home devices.
Choose the Location for the 2GIG EDGE Remote Keypad’s Backplate
Before mounting the backplate, choose a location. Work with the end user to determine the best
location. Always choose an indoor location protected from temperature extremes.

Recommended Tools and Equipment
To install the system, these tools and equipment are recommended:

➣
2-Conductor Power Wire (if connecting power supply to the panel’s terminal block)

➣
Drywall Saw (or equivalent)

➣
Screwdrivers

➣
Staple Gun

➣
Wire Stripper
Choose the Wall Location
To choose a wall location:

➣
Always choose a location that is above ground and centrally located. Do NOT install
the Panel below ground level, because wireless range may be impaired.

➣
Do NOT connect the Panel to a light switch-controlled outlet.

➣
Avoid choosing a location that can be easily viewed from doors or windows.

➣
Avoid choosing a location that is within reach of small children.

➣
Avoid choosing a location in direct sunlight.
1.
Align Backplate for Hole
Locations
Remove the backplate from the panel by backing
out the top and bottom screws until you feel
resistance.
Once removed, create mounting holes and cut a
slot in the dry wall for the AC power cord.
2.
Mount the Backplate to a Wall
Use the four (4) wall anchors and screws
(supplied).
NOTE: The
Wall Anchor is the wall tamper and
MUST be anchored to work.
Power (Terminal)
Battery Backup Terminal
Power (Barrell)
LEVEL
NOT LEVEL
Wall Tamper
Illustration displays both types of power connection:
Install the 2 - conductor power wires
or
Barrel Connector
Back Plate
Attached to Wall
Secure with
Fastener
STANDARD
DECORA
Barrel Connector
The Barrel connector is an alternate
method for connecting the AC power
supply to the Panel.
WARNING!!
Do NOT plug the power
supply into the outlet at this time.
5.
Connect Backup Battery
Align pins, then carefully insert the
battery cable.
NOTE: Back
up Battery must be
connected before AC Power is
connected to the keypad.
6.
Hang the EDGE Remote Keypad
Place the backplate over the upper lip on the
back of the chassis, and flip the Remote Keypad
downward and push until it clicks into place.
Secure the back plate by tightening the bottom
screw.
7.
Install Retaining Wall Bracket and Connect the AC Power Supply
For compliance with ANSI/NFPA 70: National Electric Code in the United States, you must
install the power supply retaining bracket (not required in Canada).
3.
Attach Hanger for Wiring
(optional)
Attach the panel’s third-hand hanging strap to
the hook at the bottom of the backplate for easy
access during wiring.
Edge Panel (upside down)
Back Plate
Hanger
4.
Connect Power
Terminal Block Wires
(DC + and DC -)
Locate a wall outlet for the plug-in
power supply, but do NOT connect the
power supply to the outlet at this time.
IMPORTANT:
Never connect the plug-in
power supply to a switch-controlled
outlet. Do not over-tighten the terminal
block’s contact screws.
OR 2GIG
®
EDGE Security & Smart Home System
2GIG-EDG-RK
| EDGE Remote Keypad
Proprietary & Confidential
Copyright © 2021 Nortek Security & Control LLC
10030219 Rev-B
After power up, the EDGE Remote
Keypad will display a message on the
screen. Press
NEXT
to continue.
If not connected already, connect your
EDGE Panel and EDGE Remote Keypad
to the same Wireless Network.
After the Keypad has connected to
the chosen WiFi network, you’ll be
prompted to press PAIR on the Main
Panel.
NOTE:
When an 2GIG Edge Remote
Keypad is available to pair on the
network, the main panel will receive a
notification message.
On the primary panel, navigate to the
Installer Toolbox (See the
2GIG EDGE
Security & Smart Home Installation &
Programming Guide
).
1.
Ta p
Panel Programming
(
).
2.
Ta p
Keypads
(
).
3.
Tap an available Keypad#, then
tap the adjacent
Keypad Used

setting (or EDIT KEYPAD).
4.
Ta p
Enabled
.
5.
Ta p
Device ID
.
6.
Ta p
PAIR KEYPAD
. The device
will search (listen) for a Keypad
7.
If desired, select
Voice
Descriptor
to assign a voice
descriptor.
8.
Ta p
EDIT
VOICE DESCRIPTOR
.
9.
Type the name of the desired
descriptor to search, then
choose from the list of available
words.
10.
Select
DONE
.
11.
Press the back button (
)
repeatedly to return to the Home
Screen.
The panels are now paired, both
displaying the Home Screen.
Pair the EDGE Remote Keypad
After mounting and powering the EDGE Remote Keypad, it will need to be setup and paired
with the EDGE Control Panel. The EDGE Remote Keypad pairs through a network connection to
the Control Panel. The network connection can be through Access Point capability directly to
the EDGE Control Panel, or through a local wireless Wi-Fi network.
NOTE:
Up to eight (8) EDGE Remote Keypads can be paired with an EDGE Control Panel.
Follow these steps and refer to “
Programming Sensors & Peripherals
” in the
2GIG EDGE
Security & Automation System Installation & Programming Guide
:
Limited Warranty
This Nortek Security & Control LLC product is warranted against defects in material and workmanship for one (1) year.
This
warranty extends only to wholesale customers
who buy direct from Nortek or through Nortek’s normal distribution channels.
Nortek Security & Control LLC does not warrant this product to consumers.
Consumers should inquire from their selling
dealer as to the nature of the dealer’s warranty, if any.
There are no obligations or liabilities on the part of Nortek Security & Control LLC for consequential damages arising out of or
in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or
profit, or cost of removal, installation, or re-installation. All implied warranties, including implied warranties for merchantability
and implied warranties for fitness, are valid only until the warranty expires. This Nortek Security & Control LLC Warranty is in
lieu of all other warranties express or implied.
All products returned for warranty service require a Return Authorization Number (RA#).
Contact Returns at 1-855-546-3351 for an RA# and other important details.
Technical Support
Should you require support services for this system, contact 2GIG Technical Support at Nortek Security &
Control.
For support in the USA and Canada, contact 2GIG Technical Support at Nortek Security & Control:

➣
Phone:
800-421-1587

➣
Online:
www.nortekcontrol.com/support/

➣
Dealer Site:
dealer.2gig.com
For support outside of the USA or Canada, contact your regional 2GIG distributor. For a list of
distributors in your region, visit the websites above.
Please refer to the 2GIG-EDG-NA User guide and Installation guide for installation instructions according to
ANSI SIA CP-01
: 2010, UL 985, and UL 1023
Installation Guide
: 10025596 Rev-A
User Guide
: 10029908 Rev-A
Operating Temperature
For optimal use, operation temperature is 0°C to 49°C (32°F to 120°F).
Typical range
: 100 Ft.