ADC-SVR122 - Installation Guide Dated 2018

STREAM VIDEO

RECORDER
QUICK INSTALLATION GUIDE
ADC-SVR122
SMARTER

VIDEO
SOLUTIONS Pre-Installation Checklist
•
SVR (included)
•
AC power adapter (included)
•
Ethernet connection to broadband (Cable, DSL or Fiber Optic) Internet
•
Login and Password for the Alarm.com account

to which you will add the SVR
Add the Device to an Alarm.com Account
1
Using an Ethernet cable, connect the device to the network.
2
Connect the device’s AC power adapter and plug it into a non-switched
outlet. Wait for the SVR Status LED (on front) to turn solid green.
3
Add the device to the account by either selecting the account in

MobileTech OR by using a web browser and entering the following URL:

www.alarm.com/addcamera
4
Select the device from the video device list or type in its MAC address

to begin adding the camera. The device’s MAC address is located on

the bottom of the device.
5
Follow the on-screen instructions to finish adding the device.

You may associate cameras to the device from the Customer Website. 2 | ADC-SVR122 Stream Video Recorder
SVR Status LED
FRONT OF SVR
SVR STATUS LED
LED Reference Guide
Solid Green |
Internet connection
Local network and Internet connection
Flashing Green |
Local network connection
Local network connection only, no Internet
Solid Red
|
Cameras not recording or hard drive error
Check LEDs on back of SVR
Flashing Red
|
No connection
Check your Internet service and the Troubleshooting section
Warning:
This will restore factory-default settings to the device. If already installed, the device

may need to be removed from the Alarm.com account and re-added after a factory reset.
To perform a factory reset, push the Reset button and release when flashing Green and Red

(about 15 seconds).
Flashing
Green
& Red
|
Factory reset 4 | ADC-SVR122 Stream Video Recorder
Lid Release
Reset
Cameras 1 - 8
USB
Ethernet
HDMI
Power
SVR Hard Drive
BACK OF SVR
SVR HARD DRIVE
CAMERAS 1 - 8
Solid Green |
SVR hard drive is operating normally
Solid Green |
Camera is connected & recording
Flashing Green |
Hard drive is full
Normal operation, oldest footage is being deleted
Flashing Green |
Recording is paused
Camera is connected and recording is paused
Flashing Red
|
Camera not recording
Camera is disconnected or improperly configured
Flashing Red
|
Hard drive configuration error
Use the Customer Website to perform diagnostics
LED Reference Guide
(CONT’D) 6 | ADC-SVR122 Stream Video Recorder
Quick Installation Guide | 7
Troubleshooting
1
If you have issues connecting the device to the account, power cycle
the device (unplug the power jack from the device and then plug it

back in to restore power). Check the Ethernet cable is properly
connected, and ensure the network has Internet access.
2
If issues persist, reset the device to factory defaults by using the
Reset button located on the back of the device. Press and hold the
Reset button until the SVR Status LED is flashing green and red

(about 15 seconds), then release the button. The device will reboot

with factory defaults. If the device was previously installed to an
Alarm.com account, it will need to be deleted before it can be

installed again.
QUESTIONS?
Visit
alarm.com/supportcenter
Viewing Live and Recorded Video Locally
1
Ensure that you have followed the setup instructions in this guide.
2
Using an HDMI cable, connect the SVR122 to a television or

computer monitor.
3
Connect a computer mouse (wireless or wired) using the USB port

on the SVR122.
4
To view the SVR122 Main Menu, move the mouse around the screen.

Three icons will appear.
MAIN MENU OPTIONS
Layouts and Rotation

Select different live view camera layout options and rotate camera feeds.
Search

Watch recorded video and control play back speeds.
Settings
View a camera’s connection status, manage camera layout locations,

and edit rotation settings.
Tip:
Click on any camera feed to access additional control options,

such as a zoom feature. © 2018 Alarm.com. All rights reserved.
8281 Greensboro Drive, Suite 100
Tysons, VA 22102
180319