Alarm.com ADC-VDB755P - Installation Guide

Alarm.com PoE Video Door Station (ADC-VDB755P) - Installation Guide
Pre-installation checklist
•
ADC-VDB755P video doorbell.
•
Video Analytics
service package
and
the
Doorbell Cameras
add-on
•
Ethernet connection to PoE (802.3af) power supply and internet access.
•
(Optional) A Wired compatible mechanical or digital chime and wired doorbell transformer.
In the box
•
ADC-VDB755P video doorbell
•
Wall anchors (x2) & screws (x2)
•
Installation card with scannable QR code
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_PoE_Video_Door_Station_(...
Updated: Thu, 17 Oct 2024 16:53:24 GMT
1 Important
: For more information about which service packages have Video Analytics, see
What service packages can
support enrolling the ADC-VDB755P?
.
Install the ADC-VDB755P
Expand all
To install the ADC-VDB755P
1.
If replacing existing doorbell hardware, turn off power to the doorbell circuit (transformer).
2.
If installing with an existing chime, remove any existing power modules from the chime. Verify that the chime wire
terminals are connected to one wire run from the transformer and one wire run from the doorbell.
3.
If replacing an existing doorbell, remove the doorbell from the wall and disconnect the wires.
Note:
If you are using the chime, secure the wires so they can be connected in a later step. If you are not using
the chime, cap the wires to safely seal and tuck away.
4.
Separate the main assembly from the wall mount assembly.
5.
Insert the chime wires (if using) and Ethernet cable through the wall mount assembly wiring cutout.
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_PoE_Video_Door_Station_(...
Updated: Thu, 17 Oct 2024 16:53:24 GMT
2 6.
Mount the main assembly to the surface with the provided screws/anchors.
7.
If installing chime wires, insert the chime wires into terminals and use a screwdriver to secure them.
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_PoE_Video_Door_Station_(...
Updated: Thu, 17 Oct 2024 16:53:24 GMT
3 8.
Connect the Ethernet cable to the Ethernet port on the back of the main assembly.
9.
Gently insert the main assembly into the wall mount assembly, ensuring that wires are not pinched and there is no
excess cable in the doorbell. Firmly press the main assembly until it is completely seated.
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_PoE_Video_Door_Station_(...
Updated: Thu, 17 Oct 2024 16:53:24 GMT
4 10.
Fasten the security screw at the bottom of the wall mount assembly.
11.
If not already completed, connect the Ethernet cable to its source of power.
12.
Restore power to the PoE source and chime circuit (if applicable).
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_PoE_Video_Door_Station_(...
Updated: Thu, 17 Oct 2024 16:53:24 GMT
5 Enroll the video doorbell
to the account
The ADC-VDB755P can be enrolled to a customer account using the MobileTech app
and customer app.
To enroll the video doorbell using the MobileTech app:
1.
Log into the MobileTech app.
2.
Find the customer account.
3.
Tap
Quick Access
.
4.
Tap
Add Device
.
5.
Tap
Video
.
6.
Follow the on-screen instructions.
To enroll the video doorbell using the customer app:
1.
Log into the
customer app. You will need the username and password of the account to log in.
2.
Tap
More
on the bottom navigation tab.
3.
Tap
Add Device
.
4.
Tap
Doorbell Camera
.
5.
Tap
ADC-VDB755P
.
6.
Follow the on-screen instructions.
LED status guide
LED pattern
Description
Off
Power off
Blinking yellow
Camera power cycling
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_PoE_Video_Door_Station_(...
Updated: Thu, 17 Oct 2024 16:53:24 GMT
6 LED pattern
Description
Solid red
No local or internet connection
Blinking red
Power on, camera booting
Blinking green
Local network connection
Solid green
Connected to Alarm.com
Alternating red and green
Camera resetting to factory default (press and hold
button for 45-50s)
Alternating yellow and white
Change the chime type to mechanical (press and hold
button for 60-65s)
•
If the chime type is set to digital or none
Alternating blue and white
Change the chime type to digital (press and hold button
for 60-65s)
•
If the chime type is set to mechanical
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_PoE_Video_Door_Station_(...
Updated: Thu, 17 Oct 2024 16:53:24 GMT
7 Notices
•
Product installation height should be less than 2 m (6’ 7”) from floor level and in a vertical orientation.
•
Operating Temperature: -58°F - 122°F (-50°C - 50°C)
ISED non-interference disclaimer
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
1.
This device may not cause interference.
2.
This device must accept any interference, including interference that may cause undesired operation of the device.
This device complies with the Canadian ICES-003 Class B specifications. CAN ICES-003(B) / NMB-003 (B).
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences
et Développement économique Canada applicables aux appareils radio exempt de licence. L’exploitation est autorisée
aux deux conditions suivantes :
1.
L’appareil ne doit pas produire de brouillage;
2.
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
Cet appareil numérique de la Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.
this device may not cause harmful interference, and
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_PoE_Video_Door_Station_(...
Updated: Thu, 17 Oct 2024 16:53:24 GMT
8 2.
this device must accept any interference received, including interference that may cause undesired operation.
Please note that changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
ISED/FCC RF Exposure statement
This equipment complies with FCC and ISED RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
In order to avoid the possibility of exceeding the FCC and ISED RSS-10 radio frequency exposure limits, this equipment
should be installed and operated with minimum distance 20 cm (7.9 inches) between the antenna and your body during
normal operation. Users must follow the specific operating instructions for satisfying RF exposure compliance.
Cet équipement est conforme aux limites d’exposition aux rayonnements FCC et ISED CNR-102 établies pour un
environnement non contrôlé. Cet émetteur ne doit pas être installé ou utilisé en conjonction avec une autre antenne ou
un autre émetteur. Afin d’éviter la possibilité de dépasser les limites d’exposition aux radiofréquences FCC et ISED, cet
équipement doit être installé et utilisé avec une distance minimale de 20 cm (7.9 pouces) entre l’antenne et votre corps
pendant le fonctionnement normal. Les utilisateurs doivent suivre les instructions spécifiques d’utilisation pour respecter
la conformité à l’exposition aux RF.
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_PoE_Video_Door_Station_(...
Updated: Thu, 17 Oct 2024 16:53:24 GMT
9