Alarm.com ADC-VDB770 - Install Guide - Dated 11/16/2020

Alarm.com Video Doorbell (ADC-VDB770) - Installation Guide
Use this guide to assist with the installation of your VDB770 doorbell camera.
Pre-installation checklist
•
ADC-VDB770 and included accessories
•
Wire crimping tool
•
Wi-Fi connection to broadband (Cable, DSL, or Fiber Optic) internet
•
A computer, tablet, or smartphone with Wi-Fi is required if the router does not have the Wi-Fi Protected Setup
(WPS) feature
•
Verify that your transformer meets the minimum voltage of 16 VAC and minimum power of 10 VA; specifications are
often written directly on the transformer
Installation
https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_Video_Doorbell_(ADC-...
Updated: Mon, 16 Nov 2020 23:35:11 GMT
1 Install the power module
1.
Verify that the electricity is turned off at the transformer before installing the power module. Locate your chime box
and remove the cover.
2.
Note the existing wire connections (e.g., the wires may be connected to the Front or Rear doorbell terminal); you
will want to connect to the same doorbell terminal in the next step. Loosen the screws on the chime associated
with the transformer and doorbell. Set the wires aside.
3.
Take the power module and hook the curved white wires onto the screw terminals (it does not matter which white
wire goes to the transformer terminal and which goes to the doorbell terminal). Tighten the screws.
4.
Using a crimp tool and the wire connectors provided, connect the wires that were set aside to the straight gray
wires of the power module.
5.
Affix the power module to the side of the chime using the included adhesive. Replace the chime cover.
https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_Video_Doorbell_(ADC-...
Updated: Mon, 16 Nov 2020 23:35:11 GMT
2 Note
:
The power module is used to prevent the chime from buzzing or humming, and it
helps ensure sufficient power is
provided to the Alarm.com
Video Doorbell.
Install the Alarm.com Video Doorbell
1.
Remove the existing doorbell from the wall and disconnect the wires. Secure the wires so that they can be
connected in a later step.
https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_Video_Doorbell_(ADC-...
Updated: Mon, 16 Nov 2020 23:35:11 GMT
3 2.
At the installation location, an angled mounting bracket can be used to modify the field of view. Choose a mounting
bracket type best suited for your installation setup. Installation scenarios corresponding to mounting bracket types
A, B, and C are provided below to guide your decision.
https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_Video_Doorbell_(ADC-...
Updated: Mon, 16 Nov 2020 23:35:11 GMT
4 3.
Thread the existing wires through the mounting bracket. Install the mounting bracket to the wall using the included
wall screws (and anchors, if needed for the mounting surface).
https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_Video_Doorbell_(ADC-...
Updated: Mon, 16 Nov 2020 23:35:11 GMT
5 4.
Thread the wire extenders through the backplate. Remove the wire caps.
5.
Crimp the two wires coming through the backplate to the existing wires threaded through the mounting bracket.
https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_Video_Doorbell_(ADC-...
Updated: Mon, 16 Nov 2020 23:35:11 GMT
6 6.
Install the doorbell backplate to the mounting bracket using the included machine screws.
7.
Attach the doorbell to the backplate by aligning and pushing together until it clicks into place and the connection is
well sealed.
8.
Turn the electricity back on. Check that the doorbell camera’s light is flashing white after the boot process is
complete.
https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_Video_Doorbell_(ADC-...
Updated: Mon, 16 Nov 2020 23:35:11 GMT
7 Note
:
If the LED is solid red after the boot-up process is complete, press and hold the main button until the light
begins alternating green and red.
Connect the ADC-VDB770 to the network
AP Mode (recommended)
1.
The camera is in Access Point (AP) mode when the button LED is blinking white. If necessary, access AP mode by
holding down the doorbell button for 45-50s and release when the LED turns to blinking white.
2.
Using a Wi-Fi-capable device (e.g., smartphone or computer), find and connect to the camera’s network; the SSID
should have the format ADC-VDB770 (XX:YY:ZZ) where XX:YY:ZZ is the last 6 characters of the MAC address,
which is printed on the included reference card.
3.
On the same device, open a web browser and enter
http://vdb770install
in the web address field. Follow the on-
screen instructions to add the ADC-VDB770 to the Wi-Fi network. Verify the LED turns solid green, indicating the
connection is complete.
WPS Mode (alternate)
Note
: Use WPS mode if you have easy access to the Wi-Fi router and the router has the WPS feature enabled. Note
that some Internet Service Providers disable the WPS feature on customer routers. AP mode is the most reliable
method for installing this device.
1.
After the boot process is complete (the camera’s LED will be blinking white), hold down the doorbell button for
30-35s and release when the LED begins to blink blue.
2.
Activate WPS Mode on the router. The router will begin to connect to the Wi-Fi network. Verify the LED turns to
https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_Video_Doorbell_(ADC-...
Updated: Mon, 16 Nov 2020 23:35:11 GMT
8 solid green, indicating the connection is complete.
Enroll the Video Doorbell to the account
Note
: The ADC-VDB770
requires a service package that supports
Video Analytics and has the
Doorbell Cameras
add-
on. For more information, see
What service packages can support enrolling the ADC-VDB770?
.
1.
Add the device to the account by selecting the account in MobileTech, by using the customer Mobile App, or by
using a web browser and entering the following web address:
www.alarm.com/addcamera
.
2.
Select the Video Doorbell from the video device list or enter in its MAC address to begin adding the device. The
device’s MAC address is located on the included reference card.
3.
Follow the on-screen instructions to finish adding the device.
Status light guide
LED pattern
Description
Off
Power off
Solid red
No local or Internet connection
Blinking red
Power on, camera booting
Solid green
Connected to Alarm.com
Blinking green
Local network connection
https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_Video_Doorbell_(ADC-...
Updated: Mon, 16 Nov 2020 23:35:11 GMT
9 LED pattern
Description
Double-blinking blue
Unable to ring indoor chime
For more information about what
causes this status,
see
What does the double-blinking blue LED on the
ADC-VDB770 mean?
.
Blinking blue
WPS mode (press and hold button for 30-45s)
Blinking white
Wi-Fi Access point mode (press and hold button for
45-60s)
Blinking yellow
Camera power cycling (press and hold button for 60-75s)
Alternating red & green
Camera resetting to factory default (press and hold
button for >75s)
Note
: If the indoor chime is enabled for the device, holding down the button will trigger a single indoor chime
immediately after being pressed. If desired, the indoor chime can be disabled through the Customer Website before
pressing the button to initiate one of the above modes.
Troubleshooting
1.
If there are issues connecting the Video Doorbell to the account, power cycle the camera by holding down the
doorbell button until the LED starts blinking yellow (~60-75s) and then releasing the button. After the device
reboots, try connecting again.
2.
If issues persist, factory reset the Video Doorbell by pressing and holding the doorbell button until the LED starts
blinking red and green (~75s). The device will reboot with factory defaults.
Important:
If the device was previously installed to an Alarm.com account, it will need to be deleted before it can be
installed again.
If the mounting bracket needs to be replaced with a different angled variety to improve the field of view, uninstall the
backplate, replace the mounting bracket (while leaving the wires connected), and reinstall the backplate to the new
https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_Video_Doorbell_(ADC-...
Updated: Mon, 16 Nov 2020 23:35:11 GMT
10 mounting bracket.
https://answers.alarm.com/ADC/Partner/Installation_and_Troubleshooting/Video_Devices/Alarm.com_Video_Doorbell_(ADC-...
Updated: Mon, 16 Nov 2020 23:35:11 GMT
11