Alarm.com ADC-VDB780B - Wireless Video Doorbell - Data Sheet

Overview
The Alarm.com Wireless Video Doorbell is a battery-
powered doorbell camera that features HD video, Video
Analytics for rapid people detection, Two-Way Audio,
a wide field of view, and a rechargeable battery.
This completely wireless video doorbell gives you the
flexibility to choose the perfect installation location
without depending on the existing wiring or chime.
The VDB780B must be connected over Wi-Fi to the
Alarm.com Smart Chime (ADC-W115C).
www.alarm.com
© 2023 Alarm.com. All rights reserved. 230209
ADC-VDB780B
DATA SHEET
Alarm.com
Wireless Video
Doorbell
Key features
• Completely wireless installation
• Rechargeable (micro USB) battery pack
• Optimized for battery life that is expected
to last up to six months
• Advanced motion detection provides
increased awareness with timely alerts
• Two-Way Audio through the mobile app
• Installation flexibility for optimal viewing
• 1 60º horizontal FOV
• Full HD 1080p recording
• Wi-Fi connection to the Alarm.com
Smart Chime (ADC-W115C) or
Smart Gateway (ADC-SG130)
(sold separately) required Specifications

Recording compression:
H.264


Ingress protection:
IP66


Max resolution:
1920x1080

Image sensor:

2.12 MP - 1080p, Sony IMX323 ABR

control support and MJPEG
Lens/angle of view:

160° horizontal, 90° vertical, 175° diagonal

Low-light sensitivity:

0.5 lux with IR LED off IR range:

Up to 15 feet (5 meters)
Image adjustments:


Flip, brightness, contrast, saturation,
sharpness, exposure


Wi-Fi connectivity:
802.11 b/g/n, 2.4 GHz


Operating and storage temperatures:

-4°F to 122°F (-20°C to 50°C)


Operating humidity:

20% to 100% (non-condensing)


Dimensions:

(W x L x D)

2.5 x 5.3 x 1.2”

(64 x 134 x 30 mm); mounting bracket
adds 0.2” (6 mm) to depth


Motion sensor:
Passive infrared sensor


Battery pack capacity:

9540mAh nominal capacity

Charging requirement:
5V/1.5A charger

Charging time:
Up to 7 hours

Speaker:
1W, 8Ω speaker


Microphone:
Single, omni-directional,
analog,>-40dBV/Pa
Included accessories
• Charging cable
• Mounting plate
• Mounting screws and anchors
• Installation guide
• 10º tilt wedge
LED guide

❶ Top LED
❷ Button LED

www.alarm.com
© 2023 Alarm.com. All rights reserved. 230209
Charging States
Mode
Description
Top LED Behavior
Button LED Behavior
Charging
The battery pack

is plugged in

and charging.
Solid orange
On Button Press

Solid green =

>75% charged
Solid yellow =

75% - 20% charged
Alternating red and blue =

< 20% charged
Fully
charged
The battery pack is
fully charged.
Solid green
On Button Press

Solid green
Failure
charging
The battery pack
stopped charging
because the device
was plugged in too
long. Remove the
charging cable and
re-attempt charging
after an hour. If you
see the same
behavior, please
contact your
provider.
Alternating orange

and green
Alternating red and white
Operational
temerature
range for
charging
exceeded
The battery

pack's internal
temperature is
either too hot or too
cold. Please charge
the battery pack in a
room temperature
environment.
Solid green or solid orange
Alternating red and yellow
Or
Alternating red and white
Operational States
Mode
Description
Button LED Behavior
Standby

or off
The camera is in standby mode (normal operation)

or the battrey is drained and requires recharging.
Off
Local
connection
The camera has a local network connection.
Solid green
No local
connection
The camera does not have a local network connection.
Solid red
Low battery
The camera's battery is low and requires a recharge.
Alternating red and blue
Connecting
to network
The camera is powered on and connecting to

a network.
Blinking red
WPS mode
The camera is in WPS pairing mode. To enter this
mode, press and hold the button for 30-45 seconds.
Blinking blue
AP mode
The camera is in AP pairing mode. To enter this mode,
press and hold the button for 46-60 seconds.
Blinking white
Power cycle
The camera is being power cycled. To enter this mode,
press and hold the button for 61-75 seconds.
Blinking yellow
Factory reset
The camera resetting to factory default. To enter this
mode, press and hold the button for 76-180 seconds.
Alternating red and green
Firmware
upgrade
The camera's firmware is being updated.
Blinking yellow rapidly