Brilliant Home Control - Smart Dimmer Switch - Install Guide Rev 2

QUICK START GUIDE
Smart Dimmer Switch Before you begin
Here’s what you need to know
before you expand your Brilliant
Smart Home System with the
Brilliant Dimmer Switch.
REQUIREMENTS
Brilliant Control:
At least one Brilliant
Control must be installed for Brilliant
Switch to work.
Neutral & Ground Wires:
Use the
Brilliant app to confirm that your
electrical wiring is supported.
Electrical:
- 120V AC
- up to 500W incandescent/halogen
- up to 200W LED/CFL
- Magnetic low voltage (MLV) lighting
not supported.
Tools:
Non-contact voltage detector,
Philips screwdriver, standard
screwdriver, pliers Install using
the Brilliant app
STEP 1 Download the app
Download the Brilliant app from the
Apple Store or Google Play Store.
STEP 2 Follow installation guide in app
Receive Step-by-Step installation
instructions from the launch screen or by
going into Settings in your Brilliant App. Wire nuts x5
Dimmer Switch
Screws
In the box Installation labels
Wire labels
Gang box labels
1
Gr ound
Gr ound
1
1
Neutr
al
Neutr
al
1
1
Line
Line
1
1
Traveler
Traveler
1
1
Load
Load
1
Load
Line Features
Motion Sensor
Customize motion
control
Slider
Dim lights:

Swipe up/down
Touch Plate
On/O:
Tap anywhere
Activate scene:

Double tap
LED
Understand
device state
Safety Disconnect
Reset Dimmer Switch Troubleshooting
Need additional help?
http://support.brilliant.tech
LED Status Indicator
White Blinking:
Powered on and ready
to be set up
White Solid:
Successfully set up and
connected to your home
Blue Blinking:
Error detected, reset
Dimmer Switch
Reset Instructions
Pull out Safety Disconnect (clear plastic
tab over LED) until LED turns o
Push in Safety Disconnect until LED
turns on.
Place your finger on Touch Plate and
hold for 10 seconds until LED turns o.
Pull out and push in safety disconnect to
cycle power. LED will blink white to
confirm reset is successful. Works with
& more The Brilliant Smart
Home System
Transform any house or apartment into
an easy-to-use smart home.
Home Control
required
Dimmer Switch
Mobile App
Smart Plug Legal
This device contains licence-exempt transmitter(s)/re-
ceiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
1.This device may not cause interference. 2. This device
must accept any interference, including interference that
may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le
présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes
: 1. L’appareil ne doit pas produire de brouillage; 2.
L’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en comprom-
ettre le fonctionnement. Legal
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to providereasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed andused in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment
and receiver.
—Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV

technician for help.
FCC CAUTION
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment. This transmitter
must not be co-located or operated in conjunction with
any other antenna or transmitter. Want to learn more about what you can
do with your Brilliant Dimmer Switch?
Visit www.brilliant.tech
510-00008 REV 2