DSC BV-600 - Installation Manual

The Bravo 6 is a specialized
twin
dual PIR motion sensor
which emphasizes immunity from false alarms caused by
pets. The Bravo 6 is equipped with a specially designed
lens
∗
∗
∗
∗
∗
which enables the detector to discriminate between
humans and small to mid-sized pets.
Exceptional design care and factory testing ensure years
of trouble free performance. Immunity against false
alarms from RF, static, electrical transients and white
light are all DSC designed in features.
Multi-Level Signal Processing
∗∗
∗∗
∗∗
∗∗
∗∗
, temperature
compensation and large multi-beam lens design means
the human target will not slip by unnoticed even on a hot
summer day.
Wall or corner mounting and vertical adjustment provide
application versatility, and your client will appreciate the
small size and elegant simplicity of the case design.
Features
• Immune to pets under 2.5 ft/0.75 m (up to 85 lbs/38 kg)
• Microprocessor based
• Advanced Multi-Level Signal (MLS) Processing
∗∗
∗∗
∗∗
∗∗
∗∗
• Twin, dual element, low noise sensors
• High level static protection
• High level transient protection
• UV stable lens
• High level of white light immunity
• Excellent RF immunity
• DSC Temperature compensation circuitry
• Harsh/Normal environment jumper
• LED on/off jumper
• Vertical adjustment
• SMD construction
• Super quiet operation
• Wall/Corner mounting
• Blends with any decor
• Compact size
∗
∗
∗
∗
∗
Protected by one or more of the following patents:
Canada CA2196014, US 5923250
∗∗
∗∗
∗∗
∗∗
∗∗
Protected by one or more of the following patents:
Canada 2099971, US 5444432
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Dual PIR
Motion Detector
Specifications
• Operating voltage: 9.5 V
DC
to 14.5 V
DC
• Supply voltage ripple: 3.0 VP-P @ 12 V
DC
• Stand-by current: 16.5 mA
• Current in alarm (LED on): 17.5 mA
• Contact rating (alarm & tamper): 100 mA @ 24 V
DC
• Alarm contact resistor in common: 28 ohm 0.25 W
• Operating temperature: 32°F to120°F / 0°C to 49°C
• Storage temperature: -40°F to140°F / -40°C to 60°C
• Operating humidity: 5% to 93% RH non-condensing
• Storage humidity: up to 99% RH non-condensing
• Radiated RF immunity:
20 V/m with 80% AM over range, 27MHz to 1.0GHz
• Conducted RF immunity:
10V with 80% AM over range 150kHz to 80MHz
• Static immunity: 15 kV
• Transient immunity: 2.4 kV @ 1.2 joules
• Walk detection speed: 0.5'/s to 10'/s (0.15 m/s to 3 m/s)
• Coverage angle (wall/wall lens): 100° maximum
• Vertical adjustment: +2° to -5°
• Mounting heights:
7' to 10.5' / 2.1m to 3.2m (nominal 7.5' / 2.3m)
Physical
Dimensions
4.9" H × 2.76" W × 1.75" D (124.5 mm × 70 mm × 44.5 mm)
Colour
White with white lens
Models
• BV-600/PBV-600: Form A alarm contact
• BV-601/PBV-601:
Form A alarm contact & tamper switch
• BV-602/PBV-602:
Form C alarm contact & tamper switch
Beam Patterns for Bravo 6 Series Lens
Side View
Top View
Locating the Detector
Select a detector location that will provide the coverage
required keeping in mind the following potential problems
Reflective Surfaces
Do not aim the detector at reflective surfaces such as
mirrors or windows as this may distort the coverage pattern
or reflect sunlight directly onto the detector.
Air Flow
Avoid locations that are subject to direct high air flow such
as near an air duct outlet.
Moisture
Do not locate the detector near sources of steam or oil.
The Sun
Do not aim the detector such that it will receive direct or
reflected (mirror) sunlight.
Obstruction
Do not limit the coverage by large objects within the
detection area such as plants or filing cabinets.
Pet Rejection
Do not aim the detector at a stairway which a pet has
access to.
Do not place furniture or objects higher than 3 ft / 0.9 m,
which a pet can climb onto (e.g. a cat on a couch), closer
than 7 ft /2.1 m to the detector. Mounting
To open the case, use a small flat blade screwdriver and
gently push in the tab at the bottom of the case and pull the
cover straight out at the bottom. Loosen the printed circuit
board screw, and push the board up as far as it will go. Using
a small screwdriver, remove the appropriate knockouts for
the mounting screws. Remove the desired wiring entrance
knockouts located at the top or bottom of the backplate.
Mount the backplate.
Locate screws diagonally opposite to each other to prevent
case warpage.
Vertical Height Guide
7.0' / 2.1 m
+ 0.25
7.5' / 2.3 m
0.00
8.5' / 2.6 m
- 0.50
9.0' / 2.7 m
- 1.00
10.5' / 3.2 m
- 1.50
Vertical Adjustment
NOTE: Range and dead zones may vary due to settings.
Using the Mounting Height chart, set the vertical adjustment
to get the desired coverage. Ensure that the PCB retaining
screw is tightened just enough to prevent board movement.
Moving the circuit board DOWN will increase the far range
and move the near beams farther out from the mounting
wall. Moving the circuit board UP will reduce the far range
and bring the near beams closer to the mounting wall.
Moving the circuit board DOWN too much will cause the far
beams to “look” above the target; as a result, the range may
appear shorter.
Jumper J1 will enable/disable the alarm LED. If J1 is OFF,
the LED will not operate on alarm. If J1 is ON, the LED will
operate on alarm. Jumper J2 selects between harsh and
normal environments. For a typical environment or one
containing a small pet lower than 1.2 ft / 0.36 m, set the unit
as normal (J2 ON). For a large pet and multiple pets, the
jumper J2 should be removed.
Wiring
NOTE: This unit is UL Listed and should be connected
to a listed control unit or power supply providing at
least 4 hours of standby power.
Walk Testing
Once the detector has been set up, walk test the entire
area where coverage is desired. Should the coverage be
incomplete, readjust or relocate the detector to obtain full
coverage. Once coverage is as required, the alarm LED
may be disabled by setting J1 to OFF.
IMPORTANT NOTE: Upon installation, the unit should
be thoroughly tested to verify proper operation. The
end user should be instructed on how to perform walk
tests, and should walk test the detector weekly.
Limited Warranty
Digital Security Controls Ltd. warrants that for a period of twelve months from the
date of purchase, the product shall be free of defects in materials and workmanship
under normal use and that in fulfilment of any breach of such warranty, Digital
Security Controls Ltd. shall, at its option, repair or replace the defective equipment
upon return of the equipment to its repair depot. This warranty applies only to defects
in parts and workmanship and not to damage incurred in shipping or handling, or
damage due to causes beyond the control of Digital Security Controls Ltd. such as
lightning, excessive voltage, mechanical shock, water damage, or damage arising
out of abuse, alteration or improper application of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be in
lieu of any and all other warranties, whether expressed or implied and of all other
obligations or liabilities on the part of Digital Security Controls Ltd. Digital Security
Controls Ltd. neither assumes, nor authorizes any other person purporting to act on
its behalf to modify or to change this warranty, nor to assume for it any other
warranty or liability concerning this product.
In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or
consequential damages, loss of anticipated profits, loss of time or any other losses
incurred by the buyer in connection with the purchase, installation or operation or
failure of this product.
Motion detectors can only detect motion within the designated areas as shown in
their respective installation instructions. They cannot discriminate between intrud-
ers and intended occupants. Motion detectors do not provide volumetric area pro-
tection. They have multiple beams of detection and motion can only be detected in
unobstructed areas covered by these beams. They cannot detect motion which oc-
curs behind walls, ceilings, floor, closed doors, glass partitions, glass doors or
windows. Any type of tampering whether intentional or unintentional such as mask-
ing, painting, or spraying of any material on the lenses, mirrors, windows or any
other part of the detection system will impair its proper operation.
Passive infrared motion detectors operate by sensing changes in temperature. How-
ever their effectiveness can be reduced when the ambient temperature rises near or
above body temperature or if there are intentional or unintentional sources of heat in
or near the detection area. Some of these heat sources could be heaters, radiators,
stoves, barbeques, fireplaces, sunlight, steam vents, lighting and so on.
Warning: Digital Security Controls Ltd. recommends that the entire system be
completely tested on a regular basis. However, despite frequent testing, and due
to, but not limited to, criminal tampering or electrical disruption, it is possible for
this product to fail to perform as expected.
Important Information: Changes or modifications not expressly approved by Digital
Security Controls Ltd. could void the user’s authority to operate this equipment.
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement
sur le matériel brouilleur du Canada.
NOTE: RF Immunity not verified by UL. Pet Immunity has not been verified by UL.
NOTE: RF Immunity not verified by UL. Pet Immunity has not been verified by UL.
NOTE: RF Immunity not verified by UL. Pet Immunity has not been verified by UL.
NOTE: RF Immunity not verified by UL. Pet Immunity has not been verified by UL.
NOTE: RF Immunity not verified by UL. Pet Immunity has not been verified by UL.
©2002 Digital Security Controls Ltd.
Toronto, Canada
Tech Line 1-800-387-3630 (Canada & US) •
www.dsc.com
Printed in Canada 29034622 R001