First Alert CAMWE-WO - VX3 Quick Install Guide 8/23

When the power is on, wait for the Halo
LED

to flash
blue. This indicates BLE
pairing mode.
Follow instruc�ons in app to complete
setup.
Installa�on Guide
VX3 HD Video
Outdoor Camera
www.resideo.com
Online Guides
TC2 Account & Password
Download and install the
Total Connect 2.0 app.
The loca�on owner’s Wi-Fi password
may be needed.
1.
2.
Connect the power supply. (If using PoE,
apply power to the PoE injector or
network switch.)
1.
3.
2.
Connec�ng to App
3A
Moun�ng Plate Installa�on
Drill Hole Through Moun�ng Surface
Skip this step if you are not routing
cables through the mounting surface.
The recommended drill bit size is 7/8in
(22.2mm) or larger.
Align and Install the Moun�ng Bracket
If routing cables through the mounting
surface, align the mounting bracket’s
center opening with the hole you drilled.
Screw the mounting bracket to the
surface with the screws provided. If
necessary, use the included wall anchors.
Prepare Cabling (Power Over Ethernet
installa�on only)
Connect PoE injector or network switch
to network source. Route Cat5/Cat6
cable to the install loca�on. Do not
power the PoE injector or switch at this
�me.
1.
2.
3a.
Prepare Cabling (Wi-Fi/Standard Power
installa�on only)
Route the included power adapter cable
from the intended wall outlet to the
install loca�on.
DO NOT
plug the power
adapter into the wall at this �me.
3b.
IMPORTANT: Before Installa�on
Included in the Box
Setup and opera�on require a Total Connect
® 2.0 account and the
Total Connect
2.0 mobile app.

Phillips #2 screwdriver
Wall Anchors
1/4in (6.3mm)
Camera
Moun�ng Bracket
12V Power Adapter
Wall Screws
5/32in (3.85mm)
PoE
Weatherproofing
Kit
Barrel Jack Connector
Weatherproofing
Kit
Hex Wrench
7/64in (3mm)
Drill
RJ45 Crimper
Cat5/Cat6 Cable
RJ45 Connector
PoE Injector or Network Switch
Home Wi-Fi Password
Tools
y
ou will need
:
Wire Stripper
Needle-Nose Pliers
Release Tool
You ma
y
need
:
3B
Drill Bit
7/8in (22.2mm)
(Pigtail Through Moun�ng Surface)
Use the Total Connect app for step-by-step
install and setup instruc�ons.
Or con�nue steps 1 to 4 below...
From the Camera screen, tap the
Add Camera
bu�on
Select the device you’re working with
Follow the in-app instruc�ons.
4
1
Cable and Power Installa�on
2
Back Box Accessory
Part # : CAMWE-WOBB
(sold separately)
Cat5/Cat6 Ethernet
Halo LED
Connec�vity
The camera supports Wi-Fi and Ethernet connectivity; select one for normal operation.
Read these instruc�ons carefully; failure to follow the instruc�ons can
damage the product or cause a hazardous condi�on.
Check the product informa�on to see if the
product is suitable for your applica�on.
A�er comple�ng installa�on, use these instruc�ons
to verify the product’s opera�on.
Power Adapter
Installa�on
Removal
Conduit Support
Supports three 1/2in (7.3mm) conduit.
Cable Management
Allows for out-of-wall cabling and
connections.
Weatherproofing
IP66 rated to ensure cable protec�on.
Stand-Off
Increase camera height in difficult
installa�on scenarios.
Easy Installa�on
Replaces standard moun�ng bracket
while retaining ease of installa�on with
minimum number of screws.
1
2
3
1
2
1
2
Press firmly
+
+
+
+
+
+
Connect Cable to Device
Connect the cable to the matching
connector on the back of the camera.
For Standard Power
Apply the weatherproofing seal around
the barrel jack connectors. If not using
standard power, use the plug on the
weatherproofing seal to protect the
unused connector.
For PoE
Apply the weatherproofing kit around
the ethernet connection. If not using
POE, the weatherproofing kit is not
required around the ethernet connector.
5a
4
A�ach Camera to the Moun�ng Bracket
Align and snap the camera to the
mounting bracket while routing the cable
bundle through the drilled hole.
Posi�on Camera
Posi�on the camera to point at the
desired area. Tighten the locking collar to
lock the camera into place.
5a.
6.
7.
Set Screw
Using the provided hex wrench, �ghten
the set screw on the collar to
permanently secure the camera’s
posi�on.
8.
Outdoor Camera Installa�on
Route Cable Through Drilled Hole
Route the cable through the hole drilled
previously. Make sure the cable doesn’t
retract.
4.
7
8
3
6
+
+
+
(Continued at right)
We recommend performing Total Connect setup
before
physical installa�on in hard-to-reach loca�ons.
For best performance and to avoid tampering, mount the camera
from 7 to 9 feet high (2.1 - 2.7 meters), with a clear field of view.
For best performance and to avoid tampering, mount the camera from 7 to 9 feet high (2.1 - 2.7 meters), with a clear field of view.
1
2
7/8in (22.2mm)
+
+
+ or
Troubleshoo�ng
Release tool
Reset Button Location
Hex Key
Paper Clip
Keep the Release Tool:
Alternative tools to release the device
may be a small Hex Key or a paper clip.
To uninstall or adjust wiring, use the Release Tool (provided)
in the pinhole at the side of the moun�ng bracket.*
*If you’re s�ll experiencing issues, follow the setup
instruc�ons in the app.
If the light does not come on, check that the power is on
and the correct cables are connected.
Removing the Camera
The reset bu�on is located on the bo�om of the device.*
Accessing the Reset Bu�on
Use Total Connect 2.0 app to adjust sensi�vity under the
doorbell camera se�ngs.
Adjus�ng Camera and Event Sensi�vity
Camera does not Power On
If the blue light does not illuminate, press the reset bu�on
for 10 seconds to ini�ate pairing mode.
Camera not in Pairing Mode
To force reboot for any reason, press the reset bu�on for 5
seconds.*
Forced Reboot
To factory reset for any reason, press the reset bu�on for
25 seconds.*
Factory Reset
SUP
PORT &
WA
RRANTY
For the latest documenta
�
on and online support informa
�
on, please go to:

www.resideo.com
For the latest warranty informa
�
on, please go to:

www.resideo.com

Responsible Party / Issuer of Supplier
’
s Declara
�
on of Conformity: Ademco Inc., a subsidiary of
Resideo Technologies, Inc.
2 C
orporate Center Dr., Melville, NY 11747, Ph: 516
-577-2000

This product manufactured by Resideo
Technologies, Inc. and its affiliates




www.resideo.com

Resideo Technologies, Inc

2 Corporate Center Drive, Suite 100

P.O. Box 9040
, Melville, NY 11747
© 2023

Resideo Technologies, Inc. All rights reserved.


The user shall not make any changes or modifica�ons to the equipment unless authorized by the Installa�on Instruc�ons or User's Manual.
Unauthorized changes or modifica�ons could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protec�on against harmful interference in a residen�al installa�on. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instruc�ons, may cause harmful interference to radio communica�ons.
However, there is no guarantee that interference will not occur in a par�cular installa�on. If this equipment does cause harmful interference to radio or
television recep�on, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•
If using an indoor antenna, have a quality outdoor antenna installed.
•
Reorient or relocate the receiving antenna.
•
Move the radio or television receiver away from the receiver/control.
•
Increase the separa�on between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC / ISED STATEMENT
This device complies with Part 15 of the FCC Rules, and ISED’s license-exempt RSSs. Opera�on is subject to the following two condi�ons:
1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired
opera�on.
Cet appareil est conforme à la par�e 15 des règles de la FCC et exempt de licence RSS d’ISED. Son fonc�onnement est soumis aux condi�ons suivantes:
(1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une
récep�on indésirable.
RF EXPOSURE STATEMENT:

The antenna(s) used for this device must be installed to provide a separa�on distance of at least 7.8 inches (20 cm) from all persons and must not be co-located
or opera�ng in conjunc�on with any other antenna or transmi�er except in accordance with FCC and ISED mul�-transmi�er product procedures.
MISE EN GARDE EXPOSITION AUX FRÉQUENCES RADIO:
La/les antenne(s) u�lisée(s) pour cet éme�eur doit/doivent être installée(s) à une distance de sépara�on d'au moins 20 cm (7,8 pouces) de toute personne et
ne pas être située(s) ni fonc�onner parallèlement à tout autre transme�eur ou antenne, excepté en conformité avec les procédures de produit mul� transme�eur
FCC et ISED.
FEDERAL COMMUNICATIONS COMMISSION & ISED STATEMENTS
This equipment should be installed in accordance with Na�onal Electrical Code, NFPA 70, Standard for the Installa�on of Residen�al Fire
Warning Systems, CAN/ULC-S540 and Chapter 2 of the Na�onal Fire Alarm Code, ANSI/NFPA 72 (Na�onal Fire Protec�on Associa�on,
Ba�erymarch Park, Quincy, MA 02269). Printed informa�on describing proper installa�on, opera�on, tes�ng, maintenance, evacua�on
planning, and repair service is to be provided with this equipment.

Canadian Installa�ons
For Installa�on in Canada, wiring shall be in accordance with CSA C22.1, Canadian Electrical Code, Part I, Safety Standard for Electrical
Installa�ons ; CAN/ULC S302, Standard for the Installa�on, Inspec�on and Tes�ng of Intrusion Alarm Systems; and CAN/ULC S301, Standard for
Signal Receiving Centre Intrusion Alarm Systems and Opera�ons.
Camera Specifications
Outdoor Camera
Part Number..........................................................................................................................................................................................CAMWE-WO
Operating Temperature...........................................................................................................................................-40 ̊F to 122 ̊F (-40 ̊C to 50 ̊C)
Operating Humidity......................................................................................................................................................
10 to 85% Non-condensing
Shipping Temperature..............................................................................................................................................
-4 ̊F to 158 ̊F (-20 ̊C to 70 ̊C)
Shipping Humidity........................................................................................................................................................
10 to 95% Non-condensing
Physical Dimensions....................................................................................................................................3 x 3 x 5 in (76.2 x 76.2 x 127.0 mm)
Color...................................................................................................................................................
...............................................................White
Power Input.......................................................................................................................................................12VDC or 802.3af PoE Class 3 PD
Microphone range....................................................................................................................................................................................10 ft (3 m)
Speaker range.............................................................................................................................................................................
..........
15 ft (4.6 m)
Weatherproofing................................................................................................................................................................................................IP66
Light On Device
Light Color
Device Status
Halo LED
White
Solid/Dim
Idle Night/Dark Conditions
White
Slow Pulse
Waiting for Bluetooth Pairing
BLE Pairing Will Begin Automatically
White
Pulsing
Firmware Update
Wait for Update to Complete
White
Brightness Increase
Person Sensed
Green
Solid
Two Way Communication
Blue
Slow Pulse
Blue
Solid
Bluetooth Pairing
Wi-Fi Pairing and Registration
Installation
In Use
Note/Resolution
Red
2 Rapid Pulse
Error/Setup Fail
Follow In-App Troubleshooting
Green
2 Rapid Pulse
Success/Confirmation
No Light
No Power
Check Wiring Connections
Yellow
Solid 5 Sec
Forced Reboot(Reset Button Pressed)
No Light
Idle Day/Bright Conditions
Spotlight
Lighting Functions
Light Behavior
Person Sensed
Colored NightVision Mode On
Solid
White
White
Tamper Alarm or Alarm Triggered
Reconnect Device or Disable Alarm
Rapid Pulsing
Removing Camera
Or con�nue steps 1 to 4 below...
From the Camera screen, tap the
Add Camera
bu�on
Select the device you’re working with
Follow the in-app instruc�ons.
Red
Solid 5 Sec
to Cycle
F
act
ory Reset(Reset But
t
on Held)
R800-28055C 8/23 Rev. C
The product (and contained ba�eries) should not be disposed of with other household waste.
Check for the nearest authorized collec�on centers or authorized recyclers. The correct disposal of
end-of-life equipment will help prevent poten�al nega�ve consequences for the environment and human health.
Any a�empt to reverse-engineer this device by decoding proprietary protocols, de-compiling firmware,
or any similar ac�ons is strictly prohibited.
CAUTION:
User should also be advised that:
The maximum antenna gain permi�ed for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non
point-to-point opera�on as appropriate. High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz
and that these radars could cause interference and/or damage to LE-LAN devices.
Les u�lisateurs devraient aussi être avisés que
Le gain maximal d’antenne permis (pour les disposi�fs u�lisant la bande 5725-5825 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploita�on point
à point et non point à point, selon le cas. De plus, les u�lisateurs de radars de haute puissance sont désignés u�lisateurs principaux (c.-à-d., qu’ils ont la priorité)
pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux disposi�fs LAN-EL.
FCC 15.407(c) states
: The device shall automa�cally discon�nue transmission in case of either absence of informa�on to transmit or
opera�onal failure.

These provisions are not intended to preclude the transmission of control or signaling informa�on or the use of repe��ve codes
used by certain digital technologies to complete frame or burst intervals.