GoControl GD00Z-8-GC - Install Guide - Dated 2020 Rev. B

GD00Z-8-GC
GARAGE DOOR OPENER
REMOTE COMMAND
TRANSCEIVER
with TILT SENSOR
Installation Instructions
1
PRODUCT DESCRIPTION
2

SAFETY NOTES
3

PRODUCT COMPONENTS
4

TILT SENSOR INSTALLATION AND BATTERY
5

PAIRING (INCLUDING) WITH THE SYSTEM
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-8-GC-GC - P/N: 10025383 Rev-B- INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - TOL. +/-.125" - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2
GD00Z-8-GC
POWER SUPPL
Y
AND BRACKET
STATUS
INDICA
TOR
WARNING
LIGHT
LINK
BUTTON
CONNECTION
WIRES
POWER
INPUT
JACK
OPTIONAL
ADJUSTABLE
GD00Z-8-GC
MOUNTING BRACKET
TILT
SENSOR
MOUNTING SCREWS
AND ANCHORS FOR
GD00Z-8-GC
SCREWS AND
MOUNTING HARDWARE
FOR ADJUSTABLE
BRACKET
SCREWS AND
MOUNTING TAPE
FOR TILT SENSOR
WIRE
TIES
1
2
GD00Z-8-GC
3
1
2
3
Note: Plug in the GD00Z-8-GC
near your Z-Wave Controller
for these steps
TO INCLUDE THE GD00Z-8-GC
INTO YOUR CONTROLLER
TO EXCLUDE THE GD00Z-8-GC
INTO YOUR CONTROLLER
Place your Z-Wave Controller into
Discovery or Include mode.
Place your Z-Wave Controller into
Exclude mode.
Press and release the link button
on the GD00Z-8-GC.
Press and release the link button
on the GD00Z-8-GC.
Confirm that the GD00Z-8-GC was
recognized by your Z-Wave Controller.
Confirm that the GD00Z-8-GC was
excluded by your Z-Wave Controller.
Refer to your Z-Wave Controllers
instructions for additional information
on including devices.
Refer to your Z-Wave Controllers
instructions for additional information
on excluding devices.
WALL
OUTLET
POWER
SUPPLY
LINK
BUTTON
POWER
INPUT
JACK
CR2032
PLUS SIDE UP !!!
SLOT
2
1
2
1
3
To activate the tilt sensor, remove the
battery protection pull strip.
The system will notify you
when the battery is low,
replace the battery with a
type CR2032 coin cell.
Use double sided tape or the two
mounting screws supplied
(drill 1/16” pilot holes if required).
Snap the sensor onto
the mounting plate.
Attach the mounting plate to
the
top panel
of the door.
Insert the
battery into the
transmitter.
To open the case, twist
a small screwdriver in
the case slot.
ARROWS ON PLATE &
SENSOR POINT UP
LOW BATTERY REPLACEMENT
“UP”
ARROWS
POST ON
BOTTOM
GD00Z-8-GC Overview
• A garage door opener remote command
transceiver with built-in Z-Wave technology.
• Allows remote operation of a garage door
opener using Z-Wave controllers.
• Acts as a Z-Wave repeater to improve
communications within the Z-Wave mesh
network.
GD00Z-8-GC Summary of Operation
•
GD00Z-8-GC connects to the garage door
opener’s pushbutton wall console terminals.
•
A wireless tilt sensor mounts on garage
door and reports door’s position to
GD00Z-8-GC.
•
GD00Z-8-GC responds to Z-Wave
commands from Z-Wave controllers to
open or close the garage door.
•
A warning indicator light flashes and a
beeper sounds for 5 seconds before the
door begins to move.
•
If the door does not completely open or
close, a second open or close command
can be sent after 30 seconds.
•
If the door does not completely open
or close after the second attempt, the
GD00Z-8-GC operation is suspended
until a local garage door pushbutton is
activated.
Z-Wave Information
•
This is a Security enabled Z-Wave product
and must be used with a Security enabled
Z-Wave controller in order to fully utilize
this product. As such, this device will not
respond to Basic CC commands.
•
ASSOCIATION:
GD00Z-8-GC supports 1
Group with 1 Node. Group 1 must be assigned
the Node ID of the controller to which
unsolicited notifications from the GD00Z-8-GC
will be sent. The Z-Wave controller should set
this association automatically after inclusion.
•
NOTIFICATION
: GD00Z-8-GC supports the
following notification types and events:
Access Control (Type 0x06) with events
0x44 (HW failure), 0x45 (UL Lockout), 0x46
(Obstruction), 0x49 (Loss of Tilt Sensor)
and 0x4A (Sensor Low Battery). And
additional type, Home Security (0x07) is
also supported with event 0x03 (Tilt Sensor
Tampered).
•
GD00Z-8-GC can be inter-operated in any
Z-Wave network with other Z-Wave devices
from other manufacturers.
S2 Security
•
Virtually impossible to hack.
•
Z-Wave hub must also support S2 Security. If
hub does not support S2, device will operate
using standard

security.
•
Security 2 DSK label can be found on the
bottom side of the product.
WARNING
This operator system is equipped with an unattended
operation feature. This door could move unexpectedly. NO
ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING
This system can be installed on sectional type (roll up) doors only
per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING
The Remote Command Transceiver must be mounted in the
garage, in sight of the garage door, where the visual and
audible movement warning indicators can be clearly seen
and heard.
WARNING
Do not install the Remote Command Transceiver on garage
door operators manufactured prior to 1993 (models without
an operational safety beam entrapment detection system).
or dial 6

GD00Z-8-GC MOUNTING
7

GD00Z-8-GC CONNECTIONS
8

SYSTEM OPERATION
9

OPERATION NOTES
1.
The warning light will flash and the warning beeper will sound for five seconds
before the door opener is activated.
STAY CLEAR OF THE DOOR AND DOOR
OPENER. THEY ARE ABOUT TO MOVE!
2.
If the door does not completely open or close after remote activation, the
GD00Z-8-GC will allow user to try to operate the door one more time. If the
second attempt fails, the GD00Z-8-GC will go into lock-out mode. See Note #3.
3.
If the GD00Z-8-GC is in lock-out mode and will not accept remote commands,
activate the door from the pushbutton wall console.
4.
Once the GD00Z-8-GC has initiated the movement of the garage door, another
command cannot be sent for 30 seconds. This eliminates the chance of
“bouncing” the garage door and possibly damaging the garage door opener.
10


TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
Unable to include
in Z-Wave
network.
GD00Z-8-GC
was not properly
excluded from a
previous Z-Wave
network.
1.
Reset the GD00Z-8-GC by pressing the LINK
button 5 times. A quick beep followed by a
longer beep will indicate the reset.
Reset should only be used in the case of a
missing or inoperative primary controller.
The GD00Z-8-GC
flashes and
beeps when
activated but the
door does not
move.
Obstruction
blocking the
door or incorrect
wiring.
2.
Make sure that there are no obstacles
preventing the door from moving.
3.
Make sure that the GD00Z-8-GC connection
wires are connected to the proper terminals
on the garage door opener. Trace the wires
from the garage door opener’s pushbutton
wall console to the door opener. This is where
the GD00Z-8-GC connection wires should be
connected.
The GD00Z-8-GC
flashes and
beeps when
activated but the
door does not
move.
The tilt sensor
signal is not being
received by the
GD00Z-8-GC.
1.
Pair the tilt sensor with the GD00Z Garage
Door Controller.
a.
Press and hold the pair button on the side
of the GD00Z-8-GC main unit for about 7
seconds. It will emit a short chirp.
b.
Release the button.
c.
Rotate the tilt sensor 90 degrees to trigger
a transmission. A short chirp should be
heard.
d.
If a short chirp is not heard, rotate the tilt
sensor again.
2.
Make sure the tilt sensor is mounted correctly
on the garage door, with the arrow pointing up.
3.
Make sure the battery pull tab has been
removed from the tilt sensor.
4.
Replace the battery in the tilt sensor.
NORTEK SECURITY & CONTROL LIMITED WARRANTY

This Nortek Security & Control product is warranted against defects in material and workmanship for twelve (12)
months.
This warranty extends only to wholesale customers
who buy direct from Nortek Security & Control
or through Nortek Security & Control’s normal distribution channels. Nortek Security & Control does not warrant
this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s
warranty, if any.
There are no obligations or liabilities on the part of Nortek Security & Control LLC for
consequential damages arising out of or in connection with use or performance of this product or other
indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or
reinstallation.
All implied warranties, including implied warranties for merchantability and implied warranties
for fitness, are valid only until the warranty expires.
This Nortek Security & Control LLC Warranty is in lieu of
all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact
Nortek Security & Control Returns at 1-855-546-3351 for an RPA# and other important details.
REGULATORY NOTICES
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate
the equipment.
Les changements ou modifications non approuvés expressément par la partie responsable de la conformité
pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.
This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
•
Consult the dealer or an experienced radio/TV technician for help
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
3/16" HOLES
FOR ANCHORS
The optional adjustable
mounting bracket fits 3 ways
on the GD00Z-8-GC
The bracket snaps onto indents
on either side or on the end of
the GD00Z-8-GC
Use the bolts and nuts supplied
to attach the bracket to a secure
structure
Secure
bracket
with screw
Use the four screws
and anchors to mount
the GD00Z-8-GC above
the opener
Tilt sensor
mounted on
the top panel
of the door
INDENT
INDENT
BE SURE THE GD00Z-8-GC IS
CLEAR OF ALL MOVING
PARTS OF THE GARAGE DOOR
AND THE WARNING LAMP IS
NOT OBSTRUCTED
INDENT
! WARNING !
The GD00Z-8-GC typically
mounts on the ceiling
near the opener and the
power outlet
REMOVE POWER FROM THE
GARAGE DOOR OPENER
BEFORE CONTINUING
THE GD00Z-8-GC WARNING
LAMP MUST BE VISIBLE IN
ALL DOOR POSITIONS
THE GD00Z-8-GC CAN ALSO BE ATTACHED TO THE OPENER'S
HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET
1
1A
2A
PUSHBUTTON
PUSHBUTTO
N
DO NOT DISCONNECT ANY WIRES CURRENTLY
CONNECTED TO THE GARAGE DOOR OPENER.
2
1
4
3
Carefully join the
power supply with
the bracket
Remove the screw from 120 VAC
outlet faceplate. Plug in the adapter.
Secure the power adapter to the faceplate
with the provided screw.
Feed the zip tie through the two holes in
the bracket and secure.
Either wire can
connect to either
terminal
Plug the power cord
into the power input
jack on the GD00Z-8-GC
Connect the GD00Z-8-GC connection wires to
the push-button wall console terminals on the
garage door opener. The terminals may be
named "PWC", "WC", "PB", "PUSHBUTTON",
or "RED and WHITE". Terminal names and
locations vary by model.
USE WIRE TIES TO
SECURE EXCESS WIRING
AWAY FROM ALL MOVING
PARTS OF THE GARAGE
DOOR AND OPENER
GARAGE
DOOR
OPENER
FLASH
FLASH
FLASH
BEEP
BEEP
BEEP
STAY CLEAR
OF THE DOOR!!!
STAY CLEAR
OF THE DOOR!!!
Restore power to your
Garage door opener.
To synchronize the system, use
the garage door opener's
push-button to manually open
and close the door.
Use the mobile app to
control your garage door,
view status and add your
garage door control to
automations and modes.
(For example, you can
schedule your garage door
to close nightly at sunset.)
The GD00Z-8-GC will beep and
flash for five seconds before
the door moves.
The GD00Z-8-GC will activate
the door opener and open or
close the garage door.
The touchscreen or mobile
app will show the new status
of the door after the door
completes its cycle.
1
2
3
4
5
6
Copyright © 2020 Nortek Security & Control LLC
10025383 Rev-B

GD00Z-8-GC Specifications

Power Supply:
Input: 120 VAC, 0.35 A

Output: 12 VDC, 1 A
Operating Temperature:
-4°—122° F (-20°—50° C)

Audible Alarm:
45 db @ 10 feet
Strobe:
360 Lumens
Communications:
Z-Wave (908.4 MHz)
Mounting:
Screws and anchors to

the ceiling, or bracket to the

opener’s hanging hardware

Tilt Sensor Specifications

Power Supply:
Type CR2032 Coin Cell Battery
Operating Temperature:
-4°—122° F (-20°—50° C)

Battery Life:
24 Months (typical)
Communications:
Proprietary 345 MHz
Range:
100 ft. line-of-sight to GD00Z-8-GC

Mounting to Garage Door:
Double-sided tape or two

mounting screws
(Specifications subject to change without notice)
NOTICE TO USERS IN CALIFORNIA - CR COIN CELL
LITHIUM BATTERY INFORMATION: THIS PRODUCT
CONTAINS A CR COIN CELL LITHIUM BATTERY
WHICH CONTAINS PERCHLORATE MATERIAL -
SPECIAL HANDLING MAY APPLY - SEE

www.dtsc.ca.gov/hazardouswaste/perchlorate
KEEP AWAY FROM SMALL CHILDREN. IF BATTERY
IS SWALLOWED, PROMPTLY SEE A DOCTOR. DO
NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL
OF USED BATTERIES MUST BE MADE IN
ACCORDANCE WITH THE WASTE RECOVERY AND
RECYCLING REGULATIONS IN YOUR AREA.