Honeywell 5800MINI - Wireless Door/Window Sensor

5800MINI
1- Zone Door/Window Transmitter
–

Installation Instructions


FEATURES

•
Single zone Door/Window Transmitter

•

Compatible with alarm systems that support 5800
series wireless devices

•

Built
-in unique serial number which must be enrolled
into the c
ontrol panel

•

Refer to the control panel’s installation instructions for
programming detail
s
.


LED Indicators

LED

Meaning

Blue

Lights when the m
agnet is within
proper
range of the
5800MINI

(1 inch max). LED is active for 15 minutes after battery is fi
rst
installed or when the cover is removed.

Green

Flashes when the
5800
MINI

transmit
s. LED is active for 15
minutes after battery is first installed or when cover is removed.

Red

Upon l
ow battery
condition, f
lashes
once
about every five
seconds
for two

minutes after a transmission
.


MOUNTING

•
Choose a mounting location where the device is stationary and the
magnet is mounted to the moving part of the door or window
.
•

Verify adequate signal strength by using the
control panel’s
Go/No Go
test (see control’s instructions) before mounting permanently.

•

Avoid mounting in areas where it will be exposed to moisture or where the
operating temperature of 32 to 120ºF (0 to 50ºC) will be exceeded.

•

Keep the 5800MINI and magnet away from metal or metallic surf
aces
such as foil wallpaper.

•

Avoid mounting the 5800M
INI
in areas with a large quantity of metal or
electrical wiring, such as a furnace or utility room.


1.

Install
the
Battery

a. Open the cover.

b. Install
the
battery with “
+
” side up.

c. Replace the c
over.


The blue and green LEDs will be active for 15
minutes. To reactivate, remove the cover.

2.

Mount the 58
00MINI & Magnet

a. Mount the 5800MINI
on the frame of the
protected door or window
using double
-
faced tape

(supplied)
.
b
.
Mount the magnet

(supplie
d)
on the
protected door or
opening portion of the
protected window
. Check that the blue LED
lights when the door or window is closed.





PROGRAMMING

Refer to the control panel’s installation instructions for programming and
enrolling the 5800MINI.

1.

Enter Programming mode at the cont
rol.

Assign a
zone number to loop
1 and assign as Input Type 3
(S
upervised RF).

2.

To enroll the serial number, activate the
transmitter twice by moving the magnet close to
and away from the module.


Alternatively, enter the device serial number
manually when prompted.


BATTERY REPLACEMENT

1.

Open the cover and
remove the ol
d battery.

2.

Install a fresh battery
with
+
side UP. See
Specifications section for compatible batteries.

3.

Replace the cover.


BATTERY CAUTION
: Risk of fire, explosion and burns. Do not
recharge, disassemble, heat above 2
12°F (100°C), or incinerate.
Dispose of used batteries properly
. Keep away from children.
Attention de batterie: Risque d'incendie, d'explosion et de brûlures. Ne
rechargez pas, démonter, chauffer au
-dessus de 212° F (100°C), ou
incinérer. Débarrassez
-vous des batteries utilisées de façon
appropriée. Gardez à partir des enfants.


SPECIFICATIONS







Dimensions:

Transmitter: 1” (25.4mm) x 2.2” (55.9mm) x 0.25”

(6.4mm)

Magnet:
0.25”
(6.35mm)

x 0
.25”
(6.35mm)

x 1” (25.4mm)

Operating
Conditions:

32
°F

(0
°
C) to 120
°F

(50
°
C)

Relative Humidity 95%, (non
-
condensing)
;
UL Tested at 85%

Magnet Gap:

1” (25.4mm) max.

Battery:

3VDC, 225mAh, Lithium Coin Cell;
Panasonic CR2032,


FEDERAL COMMUNICATIONS CO
MMISSION STATEMENT
S

The user shall not make any changes or modifications to the equipment unless authorized by the Installation
Instructions or User Manual. Unauthorized changes or modifications could void the user's authority to operate
the equipment


F
CC/IC STATEMENT

This device complies with Pa
rt 15 of the FCC Rules,
and
Industry Canada’s license
-exempt RSSs
.
Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference (2) Thi
s device must accept any
interference received, including interference that
may cause undesired operation.

Cet appareil est conforme à la partie 1
5 des règles de
la FCC et exempt de licence RSS d’Industrie Canada
.
Son fonc
tionnement est soumis aux conditions
suivantes: (1) Cet appareil ne doit pas causer d'
interférences
nuisibles. (2) Cet appareil doit accepter
toute interférence
reçue y compris les interférences

causant une
réception

indésirable.


REFER TO THE INSTALLATI
ON INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS
DEVICE IS USED
FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM.


SUPPORT & WARRANTY

For the latest documentation and online support
information, please go to:
https://mywebtech.honeywell.com/

Fo
r the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa.

For patent information
: www.honeywell.co
m/patents



MyWebTech


Warranty


Patents



2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747



201
6

Honeywell International Inc.

Ê800-22088SŠ

www.honeywell.com/security


800
-
22088

6
/1
6

Rev
C