Honeywell 5809 Data Sheet

Honeywell’s 5809 wireless fixed heat and rate-of-rise
temperature sensor offers expanded fire detection and
installation flexibility. It is ideal for hard to wire locations and
applications that require more than smoke detection. With no
wires to run, the 5809 is fast and easy to install.
The 5809 combines both rate-of-rise and fixed temperature
sensors. Fires typically cause a rapid rise in temperature in the
surrounding area. The 5809’s rate-of-rise thermostat senses
the rise in temperature and signals an alarm if the increase is
15° or more per minute. A built-in fixed temperature sensor
will also signal an alarm if the environmental temperature rises
above 135°F. The 5809 is UL Listed (UL521) and CSFM
approved for commercial and residential applications.
• Contains a built-in transmitter which
can send alarm, supervisory and
battery condition messages to the
system’s receiver/control unit
• Powered by a three-volt lithium
battery. If the battery voltage gets too
low, the 5809 sends a low battery
signal to the control panel
• Features a tamper switch, which
causes a trouble signal to be sent to
the control if the unit is removed from
the mounting base
• UL Listed for Commercial (when using
5881EH Receiver) or Residential
applications
FEATURES
5809
WIRELESS HEAT DETECTOR
ORDERING
5809
Heat Detector
L/5809/D
October 2007
© 2007 Honeywell International Inc.
Honeywell Security & Custom Electronics
Honeywell
2 Corporate Center Drive Suite 100
P.O. 9040
Melville, NY 11747
www.honeywell.com
5809
WIRELESS HEAT DETECTOR
• Power:
- 3V lithium battery (Duracell DL123A,
Panasonic CR123A, Sanyo CR123A,
Varta CR123A)
- Operating temperature: 40° to
140°F (6° to 60°C)
- Rate-of-rise temperature: 15°F (8°C)
increase per minute (NOTE: Rate-of-
rise sensor does not operate above
38°C)
- Fixed temperature: 135°F (57°C)
- Maximum spacing: 50 ft x 50 ft UL,
30 ft x 30 ft FM (refer to National Fire
Alarm Code Standard NFPA 72 for
application requirements)
- Dimensions: 4.4” diameter/2/2”
deep
•
Agency Listings:
- UL 521 Listed for Commercial
(when using 5881EH Receiver) or
Residential applications
•
Wireless Transmission Path Test:
- A good RF transmission path must
be established from the proposed
mounting location before permanently
installing the detector. To determine
that there is a good signal reception
from the proposed location, perform
the test procedure described in the
installation instructions procedure.
SPECIFICATIONS:
The test procedure should be performed
to determine a good RF transmission
path and again after installation is
completed.
CAUTION: The fixed temperature sensor
is intended for one-time use. Prolonged
heat during testing can damage the unit.
If used carefully following the instructions
described below, the heat from a portable
hair dryer can be used to test the unit. If
the round disk on top of the detector
detaches, the detector must be replaced.
- Activiate the control panel’s test mode
- Use either method (a) or (b) or activate
the detector
(a) Press and release the activation
button on the PC board assembly OR
(b) Holding a portable hair dryer about
12 to 18 inches away from the detector,
turn the dryer on and aim the warm air
at the side of the detector.
CAUTION:
Aiming the dryer directly at
the round disk on the detector can
damage the unit to be replaced.
- The system’s keypad should beep and
the detector’s ID should be displayed
- Exit the control’s test mode
FCC ID: CFS 8DL 5809
This device complies with part 15 of
FCC rules.
Operation is subject to the following
conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
TESTING THE DETECTOR:
- You can mount the 5809 on a wall or
ceiling within the protection area:
- Wall mounting: Mount the detector
4” 6” from the ceiling
Ceiling mounting: Mount the detector
at least 4” from any wall. Make sure
the normal ceiling temperature will not
exceed 100°F (37.8° C).
- Refer to NFPA Standard 72 for
detector spacing and other
requirements. Maximum spacing for
UL installations is 50’ x 50’
- Avoid mounting the detector near
heat generating devices (e.g. ovens,
heat vents, furnaces, boilers)
IMPORTANT: Heat detectors should
be used for property protection.
Reliance should not be placed soley
on heat detectors for life safety.
When life safety is involved, smoke
detectors MUST also be used.
Detectors must not be painted.
MOUNTING THE DETECTOR:
of 2

Document Transcript

5809
WIRELESS HEAT DETECTOR

Honeywell’s 5809 wireless fixed heat and rate-of-rise temperature sensor offers expanded fire detection and installation flexibility. It is ideal for hard to wire locations and applications that require more than smoke detection. With no wires to run, the 5809 is fast and easy to install. The 5809 combines both rate-of-rise and fixed temperature sensors. Fires typically cause a rapid rise in temperature in the

surrounding area. The 5809’s rate-of-rise thermostat senses the rise in temperature and signals an alarm if the increase is 15° or more per minute. A built-in fixed temperature sensor will also signal an alarm if the environmental temperature rises above 135°F. The 5809 is UL Listed (UL521) and CSFM approved for commercial and residential applications.

FEATURES
• Contains a built-in transmitter which can send alarm, supervisory and battery condition messages to the system’s receiver/control unit • Powered by a three-volt lithium battery. If the battery voltage gets too low, the 5809 sends a low battery signal to the control panel • Features a tamper switch, which causes a trouble signal to be sent to the control if the unit is removed from the mounting base • UL Listed for Commercial (when using 5881EH Receiver) or Residential applications

5809
WIRELESS HEAT DETECTOR

SPECIFICATIONS:
• Power: - 3V lithium battery (Duracell DL123A, Panasonic CR123A, Sanyo CR123A, Varta CR123A) - Operating temperature: 40° to 140°F (6° to 60°C) - Rate-of-rise temperature: 15°F (8°C) increase per minute (NOTE: Rate-ofrise sensor does not operate above 38°C) - Fixed temperature: 135°F (57°C) - Maximum spacing: 50 ft x 50 ft UL, 30 ft x 30 ft FM (refer to National Fire Alarm Code Standard NFPA 72 for application requirements) - Dimensions: 4.4” diameter/2/2” deep • Agency Listings: - UL 521 Listed for Commercial (when using 5881EH Receiver) or Residential applications • Wireless Transmission Path Test: - A good RF transmission path must be established from the proposed mounting location before permanently installing the detector. To determine that there is a good signal reception from the proposed location, perform the test procedure described in the installation instructions procedure.

MOUNTING THE DETECTOR:
- You can mount the 5809 on a wall or ceiling within the protection area: - Wall mounting: Mount the detector 4” 6” from the ceiling Ceiling mounting: Mount the detector at least 4” from any wall. Make sure the normal ceiling temperature will not exceed 100°F (37.8° C). - Refer to NFPA Standard 72 for detector spacing and other requirements. Maximum spacing for UL installations is 50’ x 50’ - Avoid mounting the detector near heat generating devices (e.g. ovens, heat vents, furnaces, boilers) IMPORTANT: Heat detectors should be used for property protection. Reliance should not be placed soley on heat detectors for life safety. When life safety is involved, smoke detectors MUST also be used. Detectors must not be painted.

TESTING THE DETECTOR:
The test procedure should be performed to determine a good RF transmission path and again after installation is completed. CAUTION: The fixed temperature sensor is intended for one-time use. Prolonged heat during testing can damage the unit. If used carefully following the instructions described below, the heat from a portable hair dryer can be used to test the unit. If the round disk on top of the detector detaches, the detector must be replaced. - Activiate the control panel’s test mode - Use either method (a) or (b) or activate the detector (a) Press and release the activation button on the PC board assembly OR (b) Holding a portable hair dryer about 12 to 18 inches away from the detector, turn the dryer on and aim the warm air at the side of the detector. CAUTION: Aiming the dryer directly at the round disk on the detector can damage the unit to be replaced. - The system’s keypad should beep and the detector’s ID should be displayed - Exit the control’s test mode FCC ID: CFS 8DL 5809 This device complies with part 15 of FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

ORDERING
5809 Heat Detector Honeywell Security & Custom Electronics Honeywell 2 Corporate Center Drive Suite 100 P.O. 9040 Melville, NY 11747 www.honeywell.com

L/5809/D October 2007 © 2007 Honeywell International Inc.

Uploaded