Honeywell GSMV Installation Manual

AlarmNet GSMV/GSMVCN
GSM Cellular Communicator Installation and Setup Guide

Requires Compass Version 1.5.8.54A (or higher) for GSM Downloading 800-07349 8/10 Rev. A

Table of Contents
                                                

SECTION 1: General Information ........................................................................................................... 1-1 System Overview ...................................................................................................................................................... 1-1 Introduction ........................................................................................................................................................ 1-1 General Information ........................................................................................................................................... 1-1 System Features......................................................................................................................................................... 1-1 Remote Services ........................................................................................................................................................ 1-2 Modes of Operation................................................................................................................................................... 1-2 ECP Mode .......................................................................................................................................................... 1-2 Zone Trigger Mode ............................................................................................................................................ 1-2 4204 Mode and Two-4204 Mode ....................................................................................................................... 1-2 Module Supervision Features .................................................................................................................................... 1-3 Antenna .............................................................................................................................................................. 1-3 Specifications ............................................................................................................................................................ 1-3 Mechanical ......................................................................................................................................................... 1-3 Electrical ............................................................................................................................................................ 1-3 RF....................................................................................................................................................................... 1-4 Environmental .................................................................................................................................................... 1-4 Compatibility............................................................................................................................................................. 1-4 Compliance................................................................................................................................................................ 1-4 Determine the Signal Strength and Select a Location ............................................................................................... 2-1 SECTION 2: Mounting and Wiring.......................................................................................................... 2-1 Mounting the GSMV................................................................................................................................................. 2-2 Standard Mounting Procedure (rear tamper switch is NOT used)...................................................................... 2-2 Mounting Procedure (rear tamper switch is used).............................................................................................. 2-3 Wiring the GSMV ..................................................................................................................................................... 2-4 Connecting and Routing the Audio Cable.......................................................................................................... 2-4 Wiring for ECP, 4204 and Two-4204 Modes..................................................................................................... 2-5 Wiring for Zone Trigger Mode........................................................................................................................... 2-6 Wiring for Module Fault Relay .......................................................................................................................... 2-7 Power Connections and Options................................................................................................................................ 2-7 Powering the Communication Module............................................................................................................... 2-7 Backup Battery Connection................................................................................................................................ 2-7 Initial Power-Up Sequence................................................................................................................................. 2-8 SECTION 3: Programming the GSMV .................................................................................................... 3-1 General Information .................................................................................................................................................. 3-1 Using the AlarmNet Direct Website................................................................................................................... 3-1 Using a 7720P Programming Tool ..................................................................................................................... 3-1 Using the Control Panel Programming Mode .................................................................................................... 3-2 Programming Conventions................................................................................................................................. 3-3 ECP Mode Programming .......................................................................................................................................... 3-3 i

GSMV/GSMVCN Installation and Setup Guide ECP Status Codes............................................................................................................................................... 3-8 Alternative Mode Programming (Zone Trigger, 4204 and Two-4204) ..................................................................... 3-8 Zone Trigger Mode ............................................................................................................................................ 3-8 4204 Emulation Mode ........................................................................................................................................ 3-8 4204 Emulation Mode Options .......................................................................................................................... 3-9 Alternative Mode Programming................................................................................................................................ 3-9 Exiting Programming Mode .................................................................................................................................... 3-17 Setting Factory Defaults................................................................................................................................... 3-18 SECTION 4: Registration .......................................................................................................................... 4-1 Registering the GSMV .............................................................................................................................................. 4-1 Registering through AlarmNet Direct Website .................................................................................................. 4-1 Using the Tamper Switch ................................................................................................................................... 4-2 Using the Programming Tool ............................................................................................................................. 4-2 Replacing an existing module using the programming tool ............................................................................... 4-3 Register by Phone............................................................................................................................................... 4-3 SECTION 5: Programmer Keyboard Commands................................................................................. 5-1 Programmer Keyboard Commands ........................................................................................................................... 5-1 Module Identification Displays .......................................................................................................................... 5-1 GSM Status Displays ......................................................................................................................................... 5-2 System Status Displays ...................................................................................................................................... 5-2 Appendices................................................................................................................................................... A-1 Appendix A : Summary of LED Operation...............................................................................................................A-1 Status Display Operation....................................................................................................................................A-1 Signal Strength (RSSI) / Mode and Status LEDs ...............................................................................................A-3 Mode and Status Indicator Switch......................................................................................................................A-3 Appendix B : Central Station Messages ....................................................................................................................B-1 Appendix C : GSM Downloading .............................................................................................................................C-1 General Information ...........................................................................................................................................C-1 Direct Wire Setup...............................................................................................................................................C-1 Appendix D : Glossary ..............................................................................................................................................D-1 Summary of Connections Diagram…………………………………………………………..……….Inside Back Cover

ii

S E C T I O N

1

General Information
                                                

System Overview
Introduction

UL

The GSMVCN has not been evaluated by UL.

Congratulations on your purchase of Honeywell's GSMV Digital Cellular Communicator (henceforth referred to as GSMV, or GSMVCN in Canada). It represents the latest and most innovative communication technology for the security industry and uses sophisticated encryption to ensure the highest level of security for your customer. In addition to alarm reporting, the GSMV provides two-way voice communications with the central station (when used with Honeywell’s AVS Audio Verification System) and provides upload/downloading capability of Honeywell's control panel data over the Internet (via the AlarmNet-G network), using GSM (Global System for Mobile) technology.
The GSMV module requires an AlarmNet–i account. For new installations, please obtain the account information from the central station prior to programming this module. For replacement installations, the AlarmNet-i account is created automatically when the module is registered (based on the existing account).

General Information Honeywell's GSMV Cellular Communicator transmits signals to the AlarmNet-G network (GSM cellular network, using GPRS) and forwards them to your central station. If the GPRS network is unavailable, the GSMV (if enabled by the dealer) will attempt to send the transmission via SMS (Short Message Service) and/or email.

ULC

SMS has not been evaluated for ULC central station communication.

The GSMV also provides support for AlarmNet Remote Services. These services allow users remote access to their security systems and provide the ability for users to be notified of system events via email.

ULC
System Features

The GSMVCN is only employed for supplemental use. A listed DACT is required to be used in conjunction with the GSMVCN to provide passive communication for fire and Level P2 channel security for burglary.

Basic features of the GSMV include:  Remote Services allow the end user to access their security system from their computer via a website. Availability of this service is controlled by the dealer via the web-based programming tool on the AlarmNet Direct website. Once enabled, remote access can be programmed via web or 7720P programming tool.  Quick connection to compatible Honeywell series control panels  Simple programming using a 7720P programming tool  Reports fire, burg, and status messages via wireless network  Allows uploading and downloading of control panel data via the wireless network  Supports remote control of alarm systems via Remote Services feature  Two-way voice capability

1-1

GSMV/GSMVCN Installation and Setup Guide

Remote Services
Honeywell now offers a new series of web based services that provides consumers with the ability to communicate with their security system remotely in a number of ways. These new web services will allow users to:  Access their security system from a computer via a website (Remote Access feature)  Receive email and text message notifications of system events (Multi-Mode feature)  Perform system functions and receive confirmations using text messages (SMS feature) Dealers will initially enroll their customers for web services during account programming through the AlarmNet Direct website. The features that can be enabled include Remote Access and Multi-Mode. Once enabled, the specific programming fields associated with these features can be programmed into the communications device either remotely using the AlarmNet Direct website or locally using the 7720P local keypad programming tool.

UL
Modes of Operation

Remote Access and Multi-Mode have not been evaluated by UL.

The GSMV provides four modes of operation so it can be used with various types of control panels, as summarized below.

ULC
ECP Mode

Only ECP Mode has been approved for ULC installations.

 This mode is for use with Honeywell controls that support LRR-ECP communication  The module connects to the control’s keypad terminals and provides 2-way communication with the control using ECP messaging  The control treats the module as a Long Range Radio (LRR) device, so program the control accordingly, including setting the module’s proper LRR device address  Reports are sent in Contact ID format  The module also supports two hardwire zone trigger inputs (zones 6 and 7)

UL

Opening and Closing ring back is fully supported.

Zone Trigger Mode  This mode is for use with controls that do not support LRR-ECP communication nor 4204 Relay Modules  The module provides six input zones  Each zone can be configured for +V, -V, or EOLR triggering  Each zone can be programmed for inverted operation, delayed reporting, and restoral reporting  Zone 1 input can distinguish between pulsed and steady signals and report fire or burglary alarms respectively  Reports are sent in ADEMCO High-Speed format

UL

Opening and Closing ring back is supported by the control panel’s digital dialer.

4204 Mode and Two-4204 Mode  This mode is for use with Honeywell controls that do not support LRR-ECP communication, but do support 4204 Relay Modules 1-2

Section 1: General Information  The module connects to the control’s keypad terminals  The control treats the module as 4204 Relay Module(s), so program the control accordingly, including setting the module’s proper 4204 device address  4204 mode provides up to four zone inputs, plus two optional trigger zones, depending on options programmed  Two-4204 mode provides up to eight zone inputs, depending on options programmed  Each 4204 zone can be programmed for delayed reporting and restoral reporting  Reports are sent in ADEMCO High-Speed format

UL

Opening and Closing ring back is supported by the control panel’s digital dialer.

Module Supervision Features
The GSMV provides the following types of supervision and module fault detection:  Network communication failure: In the event the AlarmNet network does not hear a supervisory message from the module within a specified time (“Supervision” option, 24 hours, 30 days, or none), AlarmNet notifies the central station of a communication failure.  Communication path failure: In the event the module detects a communication path failure, the control panel can be notified of a trouble condition with the module after a specified time has elapsed (“GSM Flt Time” option, 00-99 minutes).  Fault output: Terminal 11 can serve as a fail-safe trigger for module fault conditions.  If used, the fault relay will trip when the following conditions occur: tamper*, power loss*, low battery*, battery charger fault*, loss of network connectivity*, the device is not registered and the device is remotely disabled by AlarmNet.

* Alarm reporting for the noted condition must be enabled for it to trigger the fault relay.
 Primary power loss and low battery conditions (“Pwr Loss Rpt,” “Low Bat Rpt” options).  Cover tamper condition (“Tamper Rpt” option). Antenna The GSMV comes equipped with an internal antenna. This feature provides additional security to the installation by making the device tamper resistant. AMPS antennas, such as the 7825-OC antenna, cannot be used with this product.

Specifications
Mechanical Dimensions: 8.4" x 8.0" x 1.5" Weight: 2.4 lbs., with battery Electrical Input Power: 9VAC, 15VA transformer, Honeywell Model No. 1332 Backup Battery: 6V, 3.1AH, Honeywell part number K14139, (included) Expected Battery Life: 5 Years (approx.) Current Drain: 35mA average standby, 500mA peak transmit Fault Relay Output: Open collector, 12VDC, .25W max. Input Trigger Levels: (V+) 5V – 14V (V–) 0V – 1V

1-3

GSMV/GSMVCN Installation and Setup Guide RF Transceiver Type: Tri-Band GSM/GPRS Class 10 Modulation: GMSK Antenna: Internal GSM quad-band antenna 1.3 dBi gain
Transmission Frequency (MHz) GSM 850 GSM 1800 GSM 1900 824-849 1710-1785 1850-1910 Transmit Power (dBm) 33 33 33 Receive Frequency (MHz) 869-894 1805-1880 1930-1990 Receive Sensitivity (dBm) -107 -106 -105.5 Number of Channels 124 374 299 Channel Spacing (MHz) 200 200 200 Duplex Separation (kHz) 45 95 80

Band

Environmental Operating temperature: -20º to +55ºC Storage temperature: -40º to +70ºC Humidity: 0 to 95% relative humidity, non-condensing Altitude: to 10,000 ft. operating, to 40,000 ft. storage

Compatibility
For a list of control panels that are compatible with various features of this device, go to: http://www.security.honeywell.com/hsc/resources/MyWebTech. After logging on, select the applicable communication product, and then select “Compatibility Chart” under Essential Docs. For ULC Fire and Burglary installations, compatible control panels are:  Vista-32FB  Vista-128FBP  Vista-250FBP family of controls Compatible receivers are:  MX8000  7810iR-ENT  Ademco 685  FA1670C  FA1700C

ULC
Compliance

The GSMVCN has only been evaluated for communication with listed Model 7810iR-ENT internet receiver and Model MX8000 central station receiver.

This device complies with the following ULC Installation Codes and Standards: 1. The Canadian Electrical Code, Part I, Safety Standard for Electrical Installations, CSA C22.1. 2. National Building Code (NBC). 3. Standard for Installation and Services for Fire Signal Receiving Centers and Systems, CAN/ULC-S561-03. 4. Standard for Installation of Fire Alarm Systems, CAN/ULC-S524-06. 5. Standard for Installation and Classification of Burglar Alarm Systems for Financial and Commercial Premises, Safes and Vaults, CAN/ULC-S302-M91.

1-4

S E C T I O N

2

Mounting and Wiring
                                                

Determine the Signal Strength and Select a Location
The GSMV must be mounted indoors. When choosing a suitable mounting location, understand that signal strength is very important for proper operation. For most installations using the supplied antenna, mounting the unit as high as practical, and avoiding large metal components provides adequate signal strength for proper operation. You will use the communications module to determine signal strength in order to find a suitable mounting location. Note: If the SIM is already activated, the RSSI signal strength indicators will indicate signal strength. If the SIM has not been activated, the firmware in the communications module enables it to communicate with the cellular network towers (without the SIM being activated) so that signal strength measurements can be determined. In this case, you can display the signal strength by simultaneously pressing the MODE and TAMPER switches. RF Exposure Warning - The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter.

Unshielded, 22 AWG cable is recommended for GSMV power/data wires. 1. Unpack the GSMV and detach the case back by pushing up into the two tabs located at the bottom of the GSMV with the blade of a screwdriver while pulling the case back and case front apart. 2. Temporarily connect the GSMV to the AC transformer, supplied. 3. Choose the installation site with the best signal strength by observing the signal strength (RSSI) bar graph (refer to Appendix A for information about signal strength and status indications). Signal strength should be within 3-5 bars. The best signal strength is usually found at the highest point in the building, near a window. Unplug the transformer.
3 BARS MIN.

R

Y

Y

G

G

G
7845i-GSM-025-V0

4. Mark the location for the GSMV.

2-1

GSMV/GSMVCN Installation and Setup Guide

Mounting the GSMV
The communications module can be mounted in two ways depending on the installation requirements. ULC NOTES: For Commercial Fire installations, the module must be mounted to a single or double gang box. 1. Locate the Drilling Template (provided) and align with case back. Drill at the appropriate locations for either single or double gang box. 2. Locate the gang box into the mounting surface, align case back over mounting surface and install using the screws provided. Pass wires/cables through the opening in the gang box and then through the opening in the case back. 3. When all wiring is completed, attach the case front of the 7845i-GSM to the case back. Attach the top first then press the bottom section inward until it snaps into place. Secure cover using supplied screw. 4. For Commercial Burglary installations, you must install the rear tamper switch.

UL

The cover must be secured with the supplied screw.

Standard Mounting Procedure (rear tamper switch is NOT used) 1. Locate the case back over selected mounting position such that the opening in the case back is aligned with the wire/cable opening on the mounting surface. 2. Pass the wires/cable through the opening in the case back, or route through the removable knockouts located on the back cover. 3. Secure the case back to the mounting surface using four screws (supplied).
4.

When all wiring is completed, attach the case front. Position the top first, then press the bottom section until it snaps in place. Secure bottom using the supplied cover screw. (This is required for UL installations.)
MOUNTING SCREW (4) (TYP)

CASE BACK

WALL OR MOUNTING SURFACE

INTERNAL ANTENNA

MM E SE RA D OG PHON IT LE P PR TELE SM 7720 FOR TRAN T NO C CKUP .5 VA BA - 16 24 Hr MC56 R: 9 R WE AHr FO 67W Y PO . 3.1 IC: Y2 IMAR 6V PR ERY: C56 RE PM TT BA ID: GI L HE C FC LABE
RX

NA TEN AN NAL NLY TER CX O R EX MM FO HM, E! O RT US PO ICE 50 ER RV

OPTIONAL WIRING KNOCKOUT CASE FRONT

MAC

H

yw one

TX

GSM GPPS WEB MODE 2 MODE 1 RSSI

ell

OPTIONAL WIRING KNOCKOUTS TAB TAB

COVER SECURING SCREW

7845GSM-015-V0

Figure 2-1. Standard Mounting 2-2

Section 2: Mounting and Wiring Mounting Procedure (rear tamper switch is used) For installations where the use of a rear tamper switch is desired. The procedure requires the removal of the printed circuit boards and installation of the tamper screw. 1. Remove the two mounting screws, and standoff from the daughter card, as shown in Step A below. 2. Remove the daughter card by pivoting upward, as shown in Step B below. 3. Remove the lower printed circuit board by pushing down on the lower tabs and pivoting the board upward, as shown in Step C below. STEP A STEP B

ER RV MM SE RA NE D OG PHO IT LE P PR TELE SM 7720 FOR TRAN T NO C CKUP .5 VA Hr BA 6 - 16 : 9 FOR 24 - MC5 WERAHr 67W Y PO . 3.1 IC: Y2 IMAR Y: 6V 6 E PR ER MC5 ER TT BA ID: GIP L H C BE FC
RX

NA TEN AN AL LY RN ON XTE CX R E MM FO HM, E! O RT E US PO IC 50

NNA NTE AL A ERN ONLY EXT MCX FOR HM, M O 50 PORT

USE! ICE ER MM E SERV OGRA ON LED P PR LEPH 7720 FOR TE SMIT TRAN NOT - 16 UP C .5 VA Hr BACK 6 - MC5

MA

C

LA

H

yw one

ell

REMOVE 2 SCREWS AND STANDOFF

9 24 ER: FOR W 67 POW AHr ARY . 3.1 IC: Y2 PRIM ERY: 6V C56 E BATT : GIPM HER ID EL FCC

MAC

LAB

RX

TX

TX GSM GPPS WEB MODE 2 MODE 1 RSSI

Hon

eyw

ell

GSM GPPS B WE DE 2 MO DE 1 MO RSSI

GSMV-001-V0
GSMV-002-V0

STEP C

STEP D
SLIDE CARD BETWEEN TABS AND PIVOT DOWN

AN RNAL ONLY EXTE MCX FOR HM, M O 50 PORT

TEN

NA

USE! ICE ER MM E SERV OGRA ON LED P PR LEPH 7720 FOR TE SMIT TRAN NOT

SEAT SMALL CARD AND FASTEN WITH 2 SCREWS AND STANDOFF

INSTALL TAMPER SCREW

UP C .5 VA Hr BACK - 16 R: 9 FOR 24 - MC56 67W POWE AHr ARY . 3.1 IC: Y2 PRIM ERY: 6V C56 RE BATT : GIPM ID L HE FCC

MAC

LABE

RX

Hon

eyw

CONNECTOR

TX

ell

GSM S GPPB WE DE 2 MO DE 1 MO I RSS

PRESS DOWN TABS AND PIVOT UP
GSMV-003-V0

SCREW POSTS (2)

PINS
GSMV-004-V0

4. Locate the case back over selected mounting position such that the opening in the case back is aligned with the wire/cable opening on the mounting surface. 5. Pass the wires/cable through the opening in the case back, or route through the removable knockouts located on the back cover. 6. Secure the case back to the mounting surface using four screws (supplied). 7. Install the tamper screw (provided), as shown in Step C above.

2-3

GSMV/GSMVCN Installation and Setup Guide 8. Replace lower printed circuit board and then daughter card, as shown in Step D above. Be sure to engage receptacle pins by pushing in before securing the daughter card with mounting screws. When all wiring is completed, attach the case front. Position the top first, then press the bottom section until it snaps in place. Secure bottom using the supplied cover screw. (Refer to Figure 2-1.)

Wiring the GSMV

UL

  

Installation must be in accordance with the National Electrical code and UL681, Installation and Classification for Burglar and Hold-Up Alarm Systems. GSMV must be connected to a UL Listed dry contact or voltage trigger outputs of a UL Listed compatible control unit. All interconnecting wires between the UL Listed control and the GSMV must be less than 3 feet in length contained in the same room. All interconnecting wiring must be installed in rigid or EMT (where exposed on interior walls) or in flexible metal tubing if run in the walls or ceiling. Requires dialer reporting with a UL Listed control. Reporting occurs over both paths. A UL listed control must monitor the radio fault output of the GSMV. A No. 659 or other UL listed Telco Line Fault Monitor’s output must be connected to an input zone on the GSMV. Premises openings and closings should be sent via the UL listed control.

 

ULC

For ULC Commercial Fire and Burglary installations, use ECP wiring in Figure 2-7 only.

Connecting and Routing the Audio Cable The GSMV comes with a supplied audio cable to support two-way voice using an AVS Base Unit. Note the AVS Base Unit is part of Honeywell’s AVS Audio Verification System. This system consist of the AVS Base Unit, Remote Station, and the Remote Station PC board. For detailed information, please refer to the AVS Audio Verification System documentation. Follow the guidelines below for connecting the audio cable. 1. Power down the control panel and AVS Audio Verification System. (When the GSMV is fully wired up, restore power to the control panel and AVS Audio Verification System.) 2. At the GSMV, remove two [2] screws and standoff that secure the small PC board, and swing up.

MM E SE RA D OG PHON IT LE P PR TELE SM 7720 FOR TRAN T NO C CKUP .5 VA Hr BA 6 - 16 : 9 R 24 - MC5 WERAHr FO 67W Y PO . 3.1 IC: Y2 IMAR 6V PR ERY: C56 RE PM TT HE BA ID: GI EL C FC

NA TEN AN AL LY RN ON XTE CX R E MM FO HM, E! O RT US PO ICE 50 ER RV

NA TEN L AN RNA ONLY EXTE MCX FOR HM, M O 50 PORT

USE! ICE ER MM E SERV OGRA ON LED P PR LEPH 7720 FOR TE SMIT TRAN NOT

UP C .5 VA BACK 9 - 16 24 Hr 56 ER: FOR W - MC 67 POW AHr ARY . 3.1 IC: Y2 PRIM ERY: 6V C56 E BATT : GIPM HER ID EL FCC

MAC

LAB

RX

MA

C

LAB

Ho

we ney

ll

Hon

eyw

TX

ell

GSM GPPS B WE DE 2 MO DE 1 MO RSSI

RX

3. Connect one end of the audio cable to the audio connector located on the small PC board.

2-4

AUDCBL-002-V0

TX GSM GPPS WEB MODE 2 MODE 1 RSSI

Section 2: Mounting and Wiring 4. Secure the small PC board and plastic standoff with two [2] screws. Note the standoff mounts on the right side. 5. Route the audio cable to the connector on the AVS Base Unit and connect the cable.
FOR EXTERNAL ANTENNA 50 OHM, MMCX ONLY

7720P PROGRAMMER PORT NOT FOR TELEPHONE SERVICE USE! TRANSMIT LED PRIMARY POWER: 9 - 16.5 VAC BATTERY: 6V. 3.1 AHr FOR 24 Hr BACKUP FCC ID: GIPMC56 IC: Y267W - MC56

MAC LABEL HERE
RX TX

TB 1 1 2 3 4 5 6 7 8 9 10 11

Honeywell

6. Ensure the audio cable ends are secured with tie wraps to reduce strain. Wiring for ECP, 4204 and Two-4204 Modes Most Honeywell ADEMCO control panels support LRR-ECP data communication, (e.g., VISTA-10P, VISTA-15P, VISTA-20P, VISTA-128BP and VISTA-128FBP). However, there are some panels that do not. Check the Installation and Setup Guide for the control panel you are using to see if it supports ECP communication. Connect the GSMV to a compatible Honeywell VISTA control panel's ECP terminals, in parallel with keypads and other peripheral devices such as RF receiver, VIP module, etc. Wire length/gauge limitations are the same for the module as they are for keypads and other peripheral devices. To wire the module for ECP or 4204 modes, see Figure 2-2 and make the following connections:
TRANSFORMER TB1 1 2 +12V AUX GND DATA OUT DATA IN RED BLK YEL GRN 3 4 5 6 AC INPUT 1 AC INPUT 2 ECP (+) VOLTAGE INPUT GND ECP DATA IN ECP DATA OUT
J1

AUDCBL-003-V0

BATTERY

VISTA CONTROL PANEL

COMMUNICATIONS MODULE

Figure 2-2. Wiring a VISTA for ECP Mode or 4204 Modes

iGSMBR-005-V0

GSM GPPS WEB MODE 2 MODE 1 RSSI

AVS BASE UNIT

ON

ON

1

2

3

4

1

2

3

4

5

2-5

GSMV/GSMVCN Installation and Setup Guide Wiring for Zone Trigger Mode To trip a zone on the GSMV in V+ trigger mode, the positive triggering voltage from the control panel must be within 6V-13V. Trigger levels above this range may cause permanent damage to the unit. Trigger levels below this range result in unreliable operation. To trip a zone on the GSMV in V- trigger mode, the negative triggering voltage must be less than 1.0V. Connect a wire from the triggering source (bell output, voltage trigger, etc.) of the control panel to the zone input of the module, and connect a common ground between the module and control panel. Examples of zone connections follow:
TRANSFORMER TB1 1 2 AC INPUT 1 AC INPUT 2

GND + TRIGGER (VOLTAGE: 2-13V)

4 5

GND ZONE INPUT Z1/Z2
iGSMBR-007-V0
iGSMBR-008-V0

J1

BATTERY

TRIGGERING DEVICE

COMMUNICATIONS MODULE

Figure 2-3. Wiring the GSMV Zone 1 Input for a Positive (+) Trigger
TRANSFORMER TB1 1 2 AC INPUT 1 AC INPUT 2

GND

4 5

GND ZONE INPUT Z1/Z2

-TRIGGER (VOLTAGE: 0-1V)
TRIGGERING DEVICE
NOTE: TRIGGER VOLTAGE IS +V TO GROUND FALLING EDGE TRIGGER

J1

BATTERY

COMMUNICATIONS MODULE

Figure 2-4. Wiring the GSMV Zone 1 Input for a Ground (-V) Trigger

TRANSFORMER

TB1 1 2 AC AC

2K EOL RESISTOR

N.O.

N.C.

4 5

GND ZONE INPUT Z1/Z2

J1

BATTERY

COMMUNICATIONS MODULE

Figure 2-5. Wiring the GSMV Zone 1 Input for EOL Supervised N.O./N.C. Triggers 2-6

iGSMBR-010-V0

Section 2: Mounting and Wiring Wiring for Module Fault Relay You may wire and program the module's fault output trigger for fail-safe mode (see the question "FLT REL ON Y/N"). To sense a module fault at the control panel, make connections as shown in Figure 2-6, including the proper EOL resistor required by the control..

UL / ULC

A 24 hour supervisory zone must be assigned on the control panel, with the GSMV's fault relay wired to that zone.

TRANSFORMER

TB1 1 2 3 AC INPUT 1 AC INPUT 2 ECP (+) VOLTAGE INPUT GND

12V AUX GND ZONE IN (+) 2K EOL RESISTOR 4

CONTROL PANEL

11 RAD FLT
J1
iGSMBR-011-V0

BATTERY

COMMUNICATIONS MODULE

Figure 2-6. Wiring the GSMV Fault Relay to a Control Panel Zone for Normally Closed Fault

Power Connections and Options
Powering the Communication Module Primary power for the GSMV is provided by the AC plug-in transformer. For ECP communication, you must also connect the +12VDC AUX voltage output of the control panel (9.6V-13.8V typical) (see Figure 2-7). In all installations, TB1-4 GND must be connected to ground (GND) on the control panel.
TRANSFORMER

TB1 1 2 3 AC INPUT 1 AC INPUT 2 ECP (+) VOLTAGE INPUT GND

12V AUX GND 4

J1

BATTERY

CONTROL PANEL

COMMUNICATIONS MODULE

Figure 2-7. Powering the GSMV NOTE: When calculating the total load on the auxiliary power output of the control panel, budget 10mA
for the GSMV when using ECP mode.

Backup Battery Connection The included battery (K14139) is used for backup in the event of a system power loss.  The battery can provide over 24 hours of system life in the event of a power failure. 2-7

iGSMBR-013-V0

GSMV/GSMVCN Installation and Setup Guide  A programmable power loss message can alert the AlarmNet Control Center when system power is lost (power loss messages are reported within 1-3 hours of actual loss).  The module transmits a low-battery message (programmable) when the battery reaches 5.7V ±5%, indicating subsequent messages may not be transmitted.  The system shuts down when the battery reaches 5.1V, and radio transmissions are no longer possible.  If system power is restored before the module shuts down, a power restore message is sent within 1-3 hours after power is restored, and the battery is recharged using the GSMV’s built-in battery charger. If system power is restored after the GSMV has shut down, a power-on reset condition exists, the module initializes itself and the battery will recharge. Install the battery as follows, and refer to the Summary of Connections diagram at the end of this document. 1. Place the battery inside the case back. 2. Snap the right side of the battery clip onto the inside of the case back and secure the left side with the screw provided. Do not plug the battery in until after you have powered-up the GSMV.

Initial Power-Up Sequence Before connecting power, check that the following have been completed:  If using ECP, 4204 or 2-4204 Mode, terminal block TB1 V+ and GND terminals are connected to the control panel’s auxiliary power output: 12VDC nominal.  Plug in the transformer.  Connect the red and black battery cables to the battery terminals. Connect battery cable to connector J1.  Power up the control panel.  Initially, all GSMV programming options are set to the factory default settings.

2-8

S E C T I O N

3

Programming the GSMV
                                                

General Information
The GSMV is designed to deliver alarms via the GSM network to an AlarmNet central station when it is registered with a valid AlarmNet account.
The GSMV module requires an AlarmNet–i account. For new installations, please obtain the account information from the central station prior to programming this module. For replacement installations, the AlarmNet-i account is created automatically when the module is registered (based on the existing account).

You can program a GSMV by one of the following methods:  Through the AlarmNet Direct website  Through use of a 7720P Programming Tool  Through a programming mode in the control panel on panels that support this option (e.g., VISTA-128BP and FBP)

Using the AlarmNet Direct Website To program the module via the website (if you are already signed up for this service), go to: https://services.alarmnet.com/AlarmNetDirect/userlogin.aspx If you are not signed up for this service, click on “Dealer Sign-Up.” Log in and follow the on-screen prompts. Please have the following information available when programming the module: 1. Primary City ID (two-digit number) 2. Primary Central Station ID (two-digit hexadecimal number) 3. Primary Subscriber ID (four-digit number) 4. MAC ID and MAC CRC number (located on the outside of box and on label inside module) or MIN number of the device you are replacing After programming is complete, you must transfer the data to the module and the module must be registered. Refer to Section 4: Registration, for further instructions. Using a 7720P Programming Tool Connect the 7720P Programming Tool as shown below. The GSMV powers the 7720P Programming Tool via the programming jack, and automatically senses the presence of the 7720P when it is plugged in.

3-1

GSMV/GSMVCN Installation and Setup Guide

7720P PROGRAMMING JACK

Xmit Shift
M1 M0 RSSI IBS GPRS

7720 PROGRAMMING TOOL
BS / ESC / A B C

1
D

2
E

3
F

4
N /Y S

5
T

6
X

7
Shift Space

8 0 #

9
Enter

J1 BATTERY CONNECTOR

Figure 3-1. Cable Connections Each key of the 7720P has two possible functions: a normal function and a Shift function. To perform a normal key function, simply press the desired key. To perform a Shift function, press the [Shift] key, and then press the appropriate key. The prompts in this document reflect use of the 7720P Programming Tool. Table 2-1 below lists each normal and shift key function. Table 2-1. 7720P Normal and Shift Key (shift LED lit) Functions
KEY BS/ESC / N/Y SHIFT 1/A 2/B 3/C 4/D 5/E 6/F 7/S 8/T 9/X SPACE 0 #/ENTER NORMAL KEY FUNCTION [BS]: Press to delete entry SHIFT KEY FUNCTION [ESC]: Press to quit program mode; also can reset programming defaults*

[]: Scroll down programming []: Scroll up programming [N]: Press for "NO" answer [Y]: Press SHIFT-Y for "YES" answer Press before pressing a SHIFT key function. Will light SHIFT LED. LED goes out once a key is pressed. Press again for each SHIFT function desired. [1]: For entering the number 1 [A]: For entering letter A [2]: For entering the number 2 [B]: For entering letter B [3]: For entering the number 3 [C]: For entering letter C [4]: For entering the number 4 [D]: For entering letter D [5]: For entering the number 5 [E]: For entering letter E [6]: For entering the number 6 [F]: For entering letter F [7]: For entering the number 7 [S]: For entering letter S [8]: For entering the number 8 [T]: For entering letter T [9]: For entering the number 9 [X]: For entering letter X [SPACE]: For scrolling option list No SHIFT function [0]: For entering the number 0 No SHIFT function No SHIFT function [#/ENTER]: Starts programming mode; Press to accept entries

*Active only when the "Exit Programming Mode" prompt is displayed. Using the Control Panel Programming Mode Some control panels support programming of the GSMV through the control panel programming mode (e.g., Vista-128BP). If programming through the control panel, only the ECP Mode programming options are available. The "mode" questions will not be displayed, and the mode cannot be changed. For a description of key functions on the control panel keypad, and how they map to the 7720P Programming tool, refer to the control panel's Programming Guide.

3-2

7845GSM-005-V2

Section 3: Programming the GSMV Programming Conventions Programming is accomplished by answering a series of prompts (questions). Most prompts require only a [Y]es or [N]o response, while others require a numerical response (ID numbers, etc.). The current value is displayed on the second line in parentheses ( ). A "?" indicates an invalid entry. Use the [ENTER] key to accept the current entry and proceed to the next prompt. If the entered value is invalid, pressing [ENTER] re-displays the prompt; the next prompt is not displayed until a valid answer is entered. Use the up/down arrow keys to scroll through the programming questions without changing any values. Press the [ESC] key to go to the end of the list of questions.

ECP Mode Programming
The GSMV supports ECP messaging to communicate with the control panel. LRR-enabled control panels send Contact ID format alarms to the GSMV directly on the 4-wire console bus. Not all control panels support the LRR interface on ECP, so be sure to check the Installation and Setup Guide of the control panel to see if it supports this feature.

ULC

Only ECP Mode has been approved for ULC installations.

Refer to Table 2-2 for ECP Mode programming and follow the prompts. Press the [ENTER] key to begin programming.
NOTE: The central station can remotely block access to local device programming. If this has been done, the following prompt appears: Access to Prog Mode Denied

NOTE: The default programming values for ECP mode are listed in the prompts below. Table 2-2. Programming a GSMV for ECP mode only.
PROMPTS 1 2 Strt Prog Mode? (Y/N)_ Enter Password ENTRY OPTIONS [Y], [N] [0-9, A-F, N, S, T, X, Y] DESCRIPTION Enters programming mode. If a password has been previously assigned, this prompt appears. Enter a 4-digit password (0-9, A-F, N, S, T, X, Y). The next prompt appears. To begin programming the module, press [Y] and go to Prompt 9: "Device Mode." To create a password if none has been assigned, press [N] and go to Prompt 4: "Create Password." To change an existing password, press [N] and go to Prompt 5: "Change Password." Passwords can be used to protect account and programming information. If no password has been assigned, this prompt appears after pressing [N] at the "Program Device?" prompt. If a password is desired, press [Y] and go to Prompt 6: "Enter Password." If a password has already been assigned, this prompt appears after pressing [N] at the "Program Device?" prompt. Press [Y] if you want to change the password. NOTE: To clear an existing password, without entering a new one, answer [Y] to the "Change Password?" prompt, then press the [Enter] key when prompted for the new password and its confirmation.

3

Program Device? (Y/N)_

[Y], [N]

4

Create Password? (Y/N)_

[Y], [N]

5

Change Password?
(Y/N)_

[Y], [N]

3-3

GSMV/GSMVCN Installation and Setup Guide
PROMPTS 6 Enter Password ENTRY OPTIONS [0-9, A-F, N, S, T, X, Y] [0-9, A-F, N, S, T, X, Y] DESCRIPTION This prompt is displayed if [Y] was pressed in Prompt 4 or 5. Enter a 4-digit password (0-9, A-F, N, S, T, X, Y). Re-enter the password as confirmation. If the password doesn't match the first entry, the following is displayed followed by the "Exit Prog. Mode?" prompt: Verify Not OK PSWD not created Otherwise, the "Exit Prog. Mode?" prompt is displayed directly. Exits program mode. Press [N] to go back to Prompt 3. Press [ESC] to load factory defaults. Refer to the Exiting Programming Mode paragraph in this section. Press the [space] key to scroll through the modes of operation. Press [ENTER] to select ECP mode. See Table 2-4 if programming other modes.

7

Verify Password

8

Exit Prog. Mode? (Y/N)_

[Y], [N] [ESC]

9

Device Mode (ECP)_

 ECP  Zone Trig.  4204 Emu  Two 4204s

Important Information Regarding Multi-Mode Options Users can receive email notification of system events by using the Multi-Mode feature. In ECP mode, this is accomplished through emulation of a 4204 relay module, or two 4204 relay modules. When “4204-Sourced” is selected, the user can be notified of up to four events, plus two additional events if using the optional communication device zones of 6 and 7. When “2-4204-Sourced” is selected, the user can be notified of up to eight system events. The Multi-Mode address must match the address of a relay module enabled in the control panel (although you don’t actually connect a module). If using “2-4204-Sourced,” the address of the second module is automatically assigned the next device address after the first 4204. Make sure that address is also enabled in the control panel. Program outputs to trigger on system events you would like to be notified of through Output Device (Relay) programming in the control panel. These events are configured at the AlarmNet Total Connect website at: https://services.alarmnet.com/TotalConnect Multi-Mode (email notification) is intended as a convenience for the user, and does not replace Central Station reporting of critical events (alarms, troubles, etc.).

UL / ULC
10 Multi Mode (Disabled)_

Multi-Mode has not been evaluated by UL or ULC.  Disabled

Enable if you want system events sent by email to the  4204 Sourced user. Select "4204 Sourced" to send up to four events or "2-4204 Sourced" to send eight events.  2-4204 Disable for normal alarm processing and go to Prompt Sourced 12: "Primary City ID". [01-30] This address must be programmed if using the MultiMulti Mode Addr 11 Mode feature. The address must be unique from the (12)_ normal LRR device address, and the Keypad Address used for Remote Access or Direct Wire downloading. The address used must also be enabled as a 4204 relay module in Vista and First Alert control panels. See Important Information above. Important Information Regarding Primary and Secondary Accounts (Questions 12-18) Account information is provided by the central station administrator. If the control supports secondary account reporting, you will need secondary account information. The City ID, CS ID or Subscriber ID of the secondary account must differ from that of the primary account. 12 13 Primary City ID (??)_ Primary CS ID (???) [01-99] [01-FE] Enter the 2-digit primary city ID, 01-99 (decimal). Enter the 2-digit primary central station ID number, 01-FE (HEX).

3-4

Section 3: Programming the GSMV
PROMPTS 14 15 Primary Sub ID (????) En. 2nd CS Y/N (N)_ ENTRY OPTIONS [0001-9999] [Y], [N] DESCRIPTION Enter the 4-digit subscriber account number, 00019999 (decimal). Applicable only if control supports Central Station #1 and #2 Category Enable reporting for the LRR device (e.g., VISTA-128BP, FA1660C, etc.). Used if reporting to a second central station is desired. If [N], go to Prompt 19: "Device Address." Enter the 2-digit secondary city ID, 01-99 (decimal). Enter the 2-digit second central station's ID number, 01-FE (HEX). Enter the 4-digit subscriber account number for the second central station, 0001-9999. In ECP mode, the GSMV communicates with the panel as a Long Range Radio (LRR) device. Enter the appropriate ECP device address. For VISTA-10 and VISTA-20 series control panels, use address 03. For other controls, see the control panel’s Installation and Setup Guide. NOTES: 1. When programming the control, enable the LRR output. 2. The device address must be unique from the "Keypad Address" entered in Prompt 22.

16 17 18

2nd City ID (??)_ 2nd CS ID (??)_ 2nd Sub ID (????)_ Device Address (03)_

[01-99] [01-FE] [0001-9999]

19

[01-30]

UL
20

Remote access has not been evaluated by UL. Remote Access Y/N (N)_ [Y], [N] Press [Y] to allow the end user to access their system via a website. Availability of this service is controlled by the dealer via the web-based programming tool on the AlarmNet Direct website. Applies only to VISTA-128BP/250BP and FBP Series controls. If [N], and if Prompt 20: Remote Access is disabled, skip to Prompt 23: "Supervision." Must be programmed if using either the Remote Access feature or Direct Wire downloading. NOTES: 1. This address must be programmed as an alpha keypad in the control panel (Device Programming Mode). If using Remote Access, the keypad must also be enabled as an AUI (advanced user interface) keypad. DO NOT connect an actual keypad (or any other device) assigned to this address. 2. This address must be unique from the "Device Address" entered in Prompt 19. The AlarmNet network must hear at least one supervisory message from the module during this supervision period; otherwise, AlarmNet notifies the central station that a communication failure has occurred. (If the supervision period is changed after registration, you must re-register the module.) Press the [space] key to scroll through choices. UL/ULC: Must be set to 24 hours.

21

Direct Wire (N)_

Y/N

[Y], [N]

22

Keypad Address (28)_

[01-30]

23

Supervision (24 Hours)_

 30 Day  24 Hour  None

3-5

GSMV/GSMVCN Installation and Setup Guide
PROMPTS 24 Old Alarm Time 10 Minutes_ ENTRY OPTIONS 10 Minutes  15 Minutes  30 Minutes  1 Hour  2 Hours  4 Hours  8 Hours  12 Hours  24 Hours [01-99] [00] = not used DESCRIPTION The old alarm time sets how long an undeliverable alarm is retried for delivery to the central station. If the message is not validated, it is retried until the old alarm time is reached or the message is validated. Press the [space] key to scroll through choices. UL/ULC: Must be set to 10 minutes. In the event the module detects a communication path failure, enter the time delay (in minutes) before the module notifies the control panel with a trouble message (and trips the Fault Output if used; (terminal 11) see next prompt). The control panel can then notify the central station. UL/ULC: Must be one (01) minute. If enabled, the fault open collector output is normally energized to ground, and de-energizes (open circuit) in the event of a module fault. For conditions that trip the fault relay refer to Module Supervision Features in Section 1. Set to [Y] if fail-safe mode is desired. See Wiring for Module Fault Relay in Section 2. UL/ULC: Must be set to "Y." Sends a primary power loss report to the central station within 1-3 hours after its detection. A restore report is sent within 1-3 hours after power is restored. UL/ULC: Must be set to "Y." 28 Low Bat Rpt Y/N (Y)_ Tamper Rpt Y/N (Y)_ [Y], [N] Sends a low-battery report when a low battery condition exists. UL/ULC: Must be set to "Y." 29 [Y], [N] Sends a tamper report when the module detects a tamper condition. A tamper restore is automatically sent when the tamper condition clears. UL/ULC: Must be set to "Y." Important Information Regarding Zone Input Options ECP mode supports two optional hardwire zone input triggers by making connections to the module’s zone 6 and/or zone 7 terminals and programming the appropriate zone trigger options below. Each zone input can be programmed to cause an alarm under one of the following conditions:  (V+), where a positive voltage causes an alarm for normally low connections (voltage trigger, NO, NC)  (V–), where a ground trigger causes an alarm for normally high connections (open collector, NO, NC)  (EOLR) End of Line Resistor, where the input is supervised by a 2K EOL resistor. The zone can be triggered by open collector, voltage trigger, NO, NC. In addition to the above, zones can be programmed for an Inverted Trigger, where the alarm and normal states of the zones are inverted; this can serve a fail-safe supervisory purpose for certain installations. These zone inputs can also be programmed for restore reporting, and for delayed reporting, which allows time for the user to abort false alarms. NOTE: Optional hardwire zones report in ADEMCO High-Speed format. 30 31 Enable Zn6 Y/N (N)_ Zn6 Trigger Type (V+)_ [Y], [N]  (V+)  (V–)  (EOLR) Enables alarm reporting for zone 6. If [N], skip to Prompt 35: "Enable Zn7." Selects the triggering method for this zone input. Press the [space] key to scroll through choices.

25

GSM Flt Time (1 min)_

26

Flt Rel ON Y/N (N)_

[Y], [N]

27

Pwr Loss Rpt Y/N (Y)_

[Y], [N]

3-6

Section 3: Programming the GSMV
PROMPTS 32 33 Invert Zn6 Y/N (N)_ Restore Zn6 Y/N (Y)_ Delay Zn6 (secs) (00)_ Enable Zn7 Y/N (N)_ Zn7 Trigger Type (V+)_ Invert Zn7 Y/N (N)_ Restore Zn7 Y/N (Y)_ Delay Zn7 (secs) (00)_ Review? Y/N ENTRY OPTIONS [Y], [N] DESCRIPTION Inverts the alarm and normal states of the zone 6 trigger; otherwise uses normal input signal. Enables restore reporting for zone 6. UL/ULC: Must be set to “Y.” [01-15] [00] = no delay [Y], [N]  (V+)  (V–)  (EOLR) [Y], [N] [Y], [N] [01-15] [00] = no delay [Y] = review [N] = exit Defines the reporting delay in seconds for zone 6. UL/ULC: Must be set to “00.” Enables alarm reporting for zone 7. If [N], skip to Prompt 40: "Review." Selects the triggering method for this zone input. Press the [space] key to scroll through choices. Inverts the alarm and normal states of the zone 7 trigger; otherwise uses normal input signal. Enables restore reporting for zone 7. UL/ULC: Must be set to “Y.” Defines the reporting delay in seconds for zone 7. UL/ULC: Must be set to “00.” Reviewing Programming Mode Entries To review the programming options (to ensure that the correct entries have been made), press [Y]. The programming prompts are displayed again. Use the up/down arrow keys to scroll through the program fields without changing any of the values. If a value requires change, simply type in the correct value. When the last field is displayed, the “REVIEW?” prompt again appears. To exit the programming mode, press [N] in response to the "REVIEW?" prompt, and refer to Exiting Programming Mode paragraph at the end of this section.

[Y], [N]

34 35 36

37 38 39 40

3-7

GSMV/GSMVCN Installation and Setup Guide ECP Status Codes When the GSMV is configured for ECP mode, it sends status messages to the control panels for battery, power, tamper, and network connectivity failures. Some of the control panels, (e.g., VISTA-10P, VISTA-15P and VISTA-20P Series) display these on the keypad as “LngRng Radio” followed by a 4-digit code (listed below). In addition, the Contact ID codes (listed in Appendix B) for these conditions are sent to the central station by the module. Table 2-3. Common ECP Keypad Display Status Codes
STATUS CODE 0000 0880 0005 000F 0019 0400 0C80 0C8F 08E0 3000 8000 0060 DESCRIPTION Control panel lost communication with GSMV. GSMV tamper detected (cover removed). GSMV has lost contact with AlarmNet-G network. GSMV is not registered; account not activated. GSMV shutdown. GSMV power on / reset AND the control panel lost communications with GSMV. GSMV power on / reset AND tamper detected. GSMV power on / reset AND tamper detected AND not registered. GSMV tamper detected AND GSMV battery low. Primary power loss (will only be displayed in conjunction with another event). Battery charger failure (will only be displayed in conjunction with another event). Low battery (will only be displayed in conjunction with another event).

Alternative Mode Programming (Zone Trigger, 4204 and Two-4204)
Zone Trigger Mode There are six input zones available on the GSMV. Each zone is selectable for +V, -V, or EOLR trigger. The first zone input can detect both pulsed and steady signals if connected to a bell output. When using Zone Trigger mode, messages are sent in ADEMCO High-Speed format. Zones 3, 4, 5, 6 and 7 are voltage trigger inputs located on TB1 pins 6-10. Refer to Table 2-4 for Zone Trigger Mode programming and follow the prompts that pertain to Zone Trigger Mode. 4204 Emulation Mode In 4204 Emulation Mode, the GSMV communicates with a compatible Honeywell VISTA series or First Alert control panel as though it were a 4204 Relay Module. If two 4204s are enabled in the module, it acts as two 4204s at consecutive device addresses. The control panel must be configured to recognize one or two 4204 relay modules accordingly. On VISTA-32FB (or higher) control panels and First Alert equivalents, addresses 6 and 13 should not be used when the secondary 4204 is enabled. Messages are sent in ADEMCO High-Speed format. NOTE: See your control panel Installation and Setup Guide for the number of 4204 modules supported.

3-8

Section 3: Programming the GSMV 4204 Emulation Mode Options For control panels that do not support LRR-ECP communication, the 4204 Emulation modes provide a means of sending up to eight unique reports based on defined system conditions. In 4204 mode, the GSMV functions as a logical 4204 Relay Module, where each relay number, referred to in the module as zone number, can be programmed to send a report based on the output function programmed in the control for that relay. Each relay-zone can also be programmed to send a restore message of the reported condition, can be set to delay transmission of messages, and can be programmed to send reports only when a conditional zone is triggered (armed), (see Zone Input Options later in this section). In single 4204 mode, the GSMV supports up to four relay-zones. In Two-4204 mode, the GSMV functions as two 4204 modules, supporting up to eight relay-zones. 4204 Relay Outputs map to GSMV zones as follows: Second 4204 Zones First 4204 Zones
(device address entered in Prompt 14): (device address entered in Prompt 14, plus 1):

Relay 1 = Zone 1 Relay 2 = Zone 2 Relay 3 = Zone 3 Relay 4 = Zone 4 or conditional zone trigger if “report only if armed” is selected in any zone 1-3 when using single 4204 mode. NOTE: Zone 4 status is not reported when being used as the conditional (arming) trigger zone.

Relay 1 = Zone 5 Relay 2 = Zone 6 Relay 3 = Zone 7 Relay 4 = Zone 8 or conditional zone trigger if “report only if armed” is selected in any zone 1-7 when using Two-4204 mode. NOTE: Zone 8 status is not reported when being used as the conditional (arming) trigger zone or if tamper reporting is enabled.

When using the GSMV in 4204 Emulation Mode, DO NOT enable the Long-Range Radio module in control panel programming. Instead, enable the module device address(es) and program the appropriate relay activation functions for the relay-zones being used. In some control panels, it is called “relay programming” and in others it is called “output device programming.” It is recommended that “close and stay closed” (usually choice 2) action is selected. Selection of momentary activation will cause the GSMV to generate an alarm and NOT a restore, even if the GSMV is programmed to send a restore for the given zone. In 4204 mode, messages are reported in ADEMCO High-Speed format. Zone alarms (status 7) are reported with “1” (alarm) or “3” (restore) displayed in the zone position for the respective zone (e.g. alarm on zone 2: 5155 5555 7; restore 5355 5555 7). A supervision fault trouble message is automatically sent if the module detects no activity on its connection to the control. The message is: 5555 5515 5; restore message is: 5555 5535 5. Refer to Table 2-4 for 4204 Emulation Mode programming and follow the prompts that pertain to 4204 or Two-4204 mode. Check marks () indicate whether the prompt applies to that mode.

Alternative Mode Programming
Press the [ENTER] key to begin programming and follow the prompts for the mode of operation being programmed.
NOTE: The central station can remotely block access to local device programming. If this has been done, the following prompt appears: Access to Prog Mode Denied

Table 2-4. Programming a GSMV for Zone Trigger, 4204 Emulation, or Two-4204 Emulation modes. PROMPTS 1 2 Strt Prog Mode? (Y/N)_ Enter Password ZONE TRIG.   4204/ 2-4204   ENTRY OPTIONS [Y], [N] [0-9, A-F, N, S, T, X, Y] DESCRIPTION Enters programming mode. If a password has been previously assigned, this prompt appears. Enter a 4-digit password (0-9, A-F, N, S, T, X, Y). The next prompt appears.

3-9

GSMV/GSMVCN Installation and Setup Guide
PROMPTS 3 Program Device? (Y/N)_ ZONE TRIG.  4204/ 2-4204  ENTRY OPTIONS [Y], [N] DESCRIPTION To begin programming the module, press [Y] and go to Prompt 9: "Device Mode." To create a password if none has been assigned, press [N] and go to Prompt 4: "Create Password." To change an existing password, press [N] and go to Prompt 5: "Change Password." Passwords can be used to protect account and programming information. If no password has been assigned, this prompt appears after pressing [N] at the "Program Device?" prompt. If a password is desired, press [Y] and go to Prompt 6: "Enter Password." If a password has already been assigned, this prompt appears after pressing [N] at the "Program Device?" prompt. Press [Y] if you want to change the password. NOTE: To clear an existing password, without entering a new one, answer [Y] to the "Change Password?" prompt, then press the [Enter] key when prompted for the new password and its confirmation. If [Y] was pressed in Prompt 4 or 5, this prompt appears. Enter a 4-digit password (0-9, A-F, N, S, T, X, Y). Re-enter the password as confirmation. If the password doesn't match the first entry, the following is displayed followed by the "Exit Prog. Mode?" prompt: Verify Not OK PSWD not created Otherwise, the "Exit Prog. Mode?" prompt is displayed directly. Exits program mode. Press [N] to go back to Prompt 3. Press [ESC] to load factory defaults. Refer to the Exiting Programming Mode paragraph in this Section. Press the [space] key to scroll through the modes of operation. Press [ENTER] to select the mode of operation. See Table 2-2 for ECP mode programming.

4

Create Password? (Y/N)_





[Y], [N]

5

Change Password? (Y/N)





[Y], [N]

6

Enter Password





[0-9, A-F, N, S, T, X, Y] [0-9, A-F, N, S, T, X, Y]

7

Verify Password





8

Exit Prog. Mode? (Y/N)_





[Y], [N] [ESC]

9

Device Mode (ECP)_





 ECP  Zone Trig.  4204 Emu  Two 4204s

Important Information Regarding Multi-Mode Options In Zone Trigger mode, the options for Multi-Mode are "Enabled" or "Disabled." If enabled, whenever a zone on the communication device is triggered, a corresponding email message is sent INSTEAD of normal central station reports. Cover tamper will send email event 8. All communication device system events (such as power loss, low battery, etc.) are still sent to AlarmNet. Events used to send email messages are defined on the Honeywell Total Connect web site, and must correspond to events triggering the hardwired zones. Multi-Mode (email notification) is intended as a convenience for the user, and does not replace Central Station reporting of critical events (alarms, troubles, etc.).

3-10

Section 3: Programming the GSMV
PROMPTS ZONE TRIG. 4204/ 2-4204 ENTRY OPTIONS DESCRIPTION

UL
10

Multi-Mode has not been evaluated by UL. Multi Mode (Disabled)_   Enabled  Disabled Enable if you want all events sent by email to the user. Disable for normal alarm processing.

Important Information Regarding Primary Account (Questions 11-13) Account information is provided by the central station administrator. [01-99] Enter the 2-digit primary city ID, 01-99   Primary City ID 11 (decimal). (??)_ 12 13 14 Primary CS ID (???) Primary Sub ID (????) Device Address (12)_      [01-FE] [00019999] [01-15] Enter the 2-digit primary central station ID number, 01-FE (HEX). Enter the 4-digit subscriber account number, 0001-9999 (decimal). The GSMV communicates with the control panel as a 4204 relay module. Enter the appropriate address. For VISTA-10P and FA130CP Series control panels, this must be address 12. For other controls, see the control panel’s Installation and Setup Guide. NOTES: 1. The 4204 protocol limits address range to 01-15. If using 2-4204 mode, the GSMV assigns the second 4204 to the next higher device address (e.g., if entering address 12 for the first 4204, then address 13 is automatically assigned to the second 4204 module). Program the control panel accordingly. 2. The device address(es) must be unique from the "Keypad Address" entered in Prompt 17 and any other address used on the control panel.

UL
15

Remote access has not been evaluated by UL. Remote Access Y/N (N)_  [Y], [N] Press [Y] to allow the end user to access their system via a website. Availability of this service is controlled by the dealer via the webbased programming tool on the AlarmNet Direct website. Applies only to VISTA-128BP/250BP and

16

Direct Wire (N)_

Y/N



[Y], [N]

FBP Series controls.

If [N], and if Prompt 15: Remote Access is disabled, skip to Prompt 18: "Supervision."

3-11

GSMV/GSMVCN Installation and Setup Guide
PROMPTS 17 Keypad Address (28)_ ZONE TRIG. 4204/ 2-4204  ENTRY OPTIONS [01-30] DESCRIPTION This address must be programmed if using either the Remote Access feature or Direct Wire downloading. NOTES: 1. This address must be programmed as an alpha keypad in the control panel (Device Programming Mode). If using Remote Access, the keypad must also be enabled as an AUI (advanced user interface) keypad. DO NOT connect an actual keypad (or any other device) assigned to this address. 2. This address must be unique from the "Device Address" entered in Prompt 14, and cannot equal that device address plus 1 (one) if using 2-4204 mode. The AlarmNet network must hear at least one supervisory message from the module during this supervision period; otherwise, AlarmNet notifies the central station that a communication failure has occurred. (If the supervision period is changed after registration, you must re-register the module.) Press the [space] key to scroll through choices. UL/ULC: Must be set to 24 hours. Sets how long an undeliverable alarm is retried for delivery to the central station. If the message is not validated, it is retried until the old alarm time is reached or the message is validated. Press the [space] key to scroll through choices. UL/ULC: Must be set to 10 minutes. In the event the module detects a communication path failure, enter the time delay (in minutes) before the module notifies the control panel with a trouble message (and trips the Fault Output if used (terminal 11); see next question). The control panel can then notify the central station. UL/ULC: Must be one (01) minute. 21 Flt Rel ON Y/N (N)_   [Y], [N] If enabled, the fault open collector output is normally energized to ground, and de-energizes (open circuit) in the event of a module fault. For conditions that trip the fault relay refer to Module Supervision Features in Section 1. Set to [Y] if fail-safe mode is desired. See Wiring for Module Fault Relay in Section 2. UL/ULC: Must be set to "Y". 22 Pwr Loss Rpt Y/N (Y)_   [Y], [N] Sends a primary power loss report to the central station within 1-3 hours after its detection. A restore report is sent within 1-3 hours after power is restored. UL/ULC Standard Installations (using transformer and battery): Must be set to "Y" unless used with a LynxR-I series control.

18

Supervision (24 Hours)_





 30 Day  24 Hrs  None

19

Old Alarm Time 10 Minutes_





20

GSM Flt Time (1 min)_





 10 Min  15 Min  30 Min  1 Hr  2 Hrs  4 Hrs  8 Hrs  12 Hrs  24 Hrs [01-99] [00] = not used

3-12

Section 3: Programming the GSMV
PROMPTS ZONE TRIG. 4204/ 2-4204 ENTRY OPTIONS DESCRIPTION Must be set to "N" when using a LynxR-I series control. ULC Commercial Fire & Burglary Installations (powered from the control panel): Must be set to "N." 23 Low Bat Rpt Y/N (Y)_   [Y], [N] Sends a low-battery report when a low battery condition exists. A low-battery restore is automatically sent when the low battery condition clears. Alternate Installations (powered from the control panel): Must be set to "N." UL/ULC Standard Installations (using transformer and battery): Must be set to "Y" unless used with a LynxR-I series control. Must be set to "N" when using a LynxR-I series control. ULC Commercial Fire & Burglary Installations (powered from the control panel): Must be set to "N." Sends a tamper report when the module detects a tamper condition. A tamper restore is automatically sent when the tamper condition clears. UL/ULC: Must be set to "Y." Applies only if used with a Lynx, LynxR or LynxR-EN control LRR trigger connected to the module's zone terminal. Reports a Panic alarm on zone 3 when the module detects a single pulse on zone 1. No restores are generated for a Panic alarm.

24

Tamper Rpt Y/N (Y)_





[Y], [N]

25

Lynx Panic Y/N (Y)_



[Y], [N]

Important Information Regarding Zone Input Options If desired, 4204 mode supports two optional hardwire zone input triggers by making connections to the module’s zone 6 and/or zone 7 terminals and programming the appropriate zone trigger options below. NOTE: These triggers are not available when using 2-4204 mode. Zone Trigger Mode provides six hardwire zone input triggers by making connections to the module’s zone terminals and programming the appropriate zone trigger options below. Zones are numbered 1-7, with zone 2 serving as a reporting zone only (see Bell Output Zone below). Bell Output Zone 1 (and 2): The zone 1 terminal can detect both pulsed and steady signals. If connecting the bell output to the GSMV zone causes a bell fault on the control panel, enable the "Trip Inputs 1or2" option. The GSMV reports an alarm on zone 1 (fire) when it detects a pulsed signal and an alarm on zone 2 (burglary) when it detects a steady signal. Telco Zone and Open/Close Zone: Dedicated zones can be assigned as the Telco fault zone and/or an open/close (arm/disarm) reporting zone. When triggered, these zones report a Telco line fault or open/close report respectively, in ADEMCO High-Speed format. Connect the appropriate trigger from the control to the selected zone input for each of these options. Input Trigger Types: Triggering of each zone input can be programmed to cause an alarm under one of the following conditions:  (V+), where a positive voltage causes an alarm for normally low connections (voltage trigger, NO, NC)  (V–), where a ground trigger causes an alarm for normally high connections (open collector, NO, NC)  (EOLR) End of Line Resistor, where the input is supervised by a 2K EOL resistor. The zone can be triggered by open collector, voltage trigger, NO, NC. Inverted Trigger: Zones can be programmed for inverted trigger, where the alarm and normal states of the zones are inverted; this can serve a fail-safe supervisory purpose for certain installations. Restore and Delayed Reports: Zone inputs can be programmed for restore reporting, and for delayed reporting (allowing time for the user to abort false alarms).

3-13

GSMV/GSMVCN Installation and Setup Guide
PROMPTS ZONE TRIG. 4204/ 2-4204 ENTRY OPTIONS DESCRIPTION

UL: Zone restoral must be enabled. Report Only if Armed option: To help eliminate redundant reports, zone alarms can be restricted to report only if a conditional zone is triggered (armed). If this feature is desired, the conditional zone is automatically used as the “arming” zone. Connect the appropriate control panel trigger to the conditional (arming) zone. The trigger must be programmed as necessary in the control panel. The conditional (arming) zone on the module is a different dedicated zone for each programming mode, as follows: Mode Zone Trigger 4204 2-4204 Conditional (Arming) Zone 7 4 8

IMPORTANT: If any zone (zones 1-6 in zone trigger mode, zones 1-3 in 4204 mode, zones 1-7 in 2-4204 mode) is set for Report Only if Armed, the conditional (arming) zone becomes unavailable for reporting (as it is reserved for the “arming” trigger connection). 26 Trip Inputs 1or2 w/Bell Out (N)_  [Y], [N] Use if the zone 1 connection to the control's bell output causes a bell fault on the control panel. NOTE: If used, EOLR trigger type is not available for zones 1 and 3. See "Important Information Regarding Zone Input Options" on previous page. Enter the zone number to be used for Telco line fault reports. This zone assignment must be unique from the open/close zone selected in Prompt 28. Zone Trigger Mode: If any zone is programmed for "report only if armed," zone 7 cannot be used. 4204 Mode: If any zone is programmed for "report only if armed," zone 4 cannot be used as a Telco zone. 2-4204 Mode: If any zone is programmed for "report only if armed," or if tamper reporting is enabled, zone 8 cannot be used. NOTE: Connect the Telco line fault output (or relay output programmed for "Telco line fault") to the Telco zone. Enter the zone number to be used for open/close (arm/disarm) reports. This zone assignment must be unique from the Telco zone selected in Prompt 27. Zone Trigger Mode: If any zone is programmed for "report only if armed," zone 7 cannot be used. 4204 Mode: If any zone is programmed for "report only if armed," zone 4 cannot be used as an open/close zone. 2-4204 Mode: If any zone is programmed for "report only if armed," or if tamper is enabled, zone 8 cannot be used. NOTE: Connect an open/close (arm/disarm) trigger (or relay output) from the control panel to the open/close zone. Selects the triggering method for this zone input. Press the [space] key to scroll through choices.

27

Telco Zone (0)_





Zone Trig: [3-7] 4204: [1-4] 2-4204: [1-8] [0] = not used

28

Open/Close Zone (0)_





Zone Trig: [3-7] 4204: [1-4] 2-4204: [1-8] [0] = not used

29

Zn1 Trigger Type (V+)_



 (EOLR)  (V+)  (V–)

3-14

Section 3: Programming the GSMV
PROMPTS 30 31 Restore Zn1 Y/N (Y)_ Delay Zn1 (secs) (00)_ Rpt Zn1 ONLY if Armed (N)_ ZONE TRIG.   4204/ 2-4204   ENTRY OPTIONS [Y], [N] [01-15] [00] = no delay   [Y], [N] DESCRIPTION Enables restore reporting for zone 1. Defines the reporting delay in seconds for zone 1. Reports alarms on zone 1 ONLY if the conditional zone (zone 7 in zone trigger mode; zone 4 in 4204 mode; or zone 8 in 2-4204 mode) is triggered (armed). If [N], always reports alarms on zone 1. 33 Invert Zn2 Y/N (N)_ Restore Zn2 Y/N (Y)_ Delay Zn2 (secs) (00)_ Rpt Zn2 ONLY if Armed (N)_  [Y], [N] Inverts the alarm and normal states of the zone 2 trigger; otherwise uses normal input signal. Enables restore reporting for zone 2. UL/ULC: Must be set to “Y.”   [01-15] [00] = no delay   [Y], [N] Defines the reporting delay in seconds for zone 2. UL/ULC: Must be set to “00.” Reports alarms on zone 2 ONLY if the conditional zone (zone 7 in zone trigger mode; zone 4 in 4204 mode; zone 8 in 2-4204 mode) is triggered (armed). If [N], always reports alarms on zone 2. 37 Zn3 Trigger Type (V+)_ Invert Zn3 Y/N (N)_ Restore Zn3 Y/N (Y)_ Delay Zn3 (secs) (00) Rpt Zn3 ONLY if Armed (N)_   (EOLR)  (V+)  (V–) [Y], [N] Selects the triggering method for this zone input. Press the [space] key to scroll through choices. Inverts the alarm and normal states of the zone 3 trigger; otherwise uses normal input signal. Enables restore reporting for zone 3. UL/ULC: Must be set to “Y.”   [01-15] [00] = no delay   [Y], [N] Defines the reporting delay in seconds for zone 3. UL/ULC: Must be set to “00.” Reports alarms on zone 3 ONLY if the conditional zone (zone 7 in zone trigger mode; zone 4 in 4204 mode; zone 8 in 2-4204 mode) is triggered (armed). If [N], always reports alarms on zone 3. 4204 mode: If any zone is programmed to "Report Only if Armed," skip to Prompt 52: "Enable Zn6." 42 Zn4 Trigger Type (V+)_ Invert Zn4 Y/N (N)_ Restore Zn4 Y/N (Y)_   (EOLR)  (V+)  (V–) [Y], [N] Selects the triggering method for this zone input. Press the [space] key to scroll through choices. Inverts the alarm and normal states of the zone 4 trigger; otherwise uses normal input signal. Enables restore reporting for zone 4. UL/ULC: Must be set to “Y.”

32

34 35





[Y], [N]

36

38



39 40





[Y], [N]

41

43



44





[Y], [N]

3-15

GSMV/GSMVCN Installation and Setup Guide
PROMPTS 45 Delay Zn4 (secs) (00) Rpt Zn4 ONLY if Armed (N)_ ZONE TRIG.  4204/ 2-4204  ENTRY OPTIONS [01-15] [00] = no delay  24204 only [Y], [N] DESCRIPTION Defines the reporting delay in seconds for zone 4. UL/ULC: Must be set to “00.” Reports alarms on zone 4 ONLY if the conditional zone (zone 7 in zone trigger mode; zone 8 in 2-4204 mode) is triggered (armed). If [N], always reports alarms on zone 4. 47 Zn5 Trigger Type (V+)_ Invert Zn5 Y/N (N)_ Restore Zn5 Y/N (Y)_ Delay Zn5 (secs) (00)_ Rpt Zn5 ONLY if Armed (N)_   (EOLR)  (V+)  (V–) [Y], [N] 24204 only 24204 only 24204 only 4204 only  4204 only 4204 only   Selects the triggering method for this zone input. Press the [space] key to scroll through choices. Inverts the alarm and normal states of the zone 5 trigger; otherwise uses normal input signal. Enables restore reporting for zone 5. UL/ULC: Must be set to “Y.” [01-15] [00] = no delay [Y], [N] Defines the reporting delay in seconds for zone 5. UL/ULC: Must be set to “00.” Reports alarms on zone 5 ONLY if the conditional zone (zone 7 in zone trigger mode; zone 8 in 2-4204 mode) is triggered (armed). If [N], always reports alarms on zone 5. 52 53 Enable Zn6 Y/N (N)_ Zn6 Trigger Type (V+)_ Invert Zn6 Y/N (N)_ Restore Zn6 Y/N (Y)_ Delay Zn6 (secs) (00)_ Rpt Zn6 ONLY if Armed (N)_ [Y], [N]  (EOLR)  (V+)  (V–) [Y], [N] Enables alarm reporting for zone 6. If [N], skip to Prompt 58: "Enable Zn7." Selects the triggering method for this zone input. Press the [space] key to scroll through choices. Inverts the alarm and normal states of the zone 6 trigger; otherwise uses normal input signal. Enables restore reporting for zone 6. UL: Must be set to “Y.”  [01-15] [00] = no delay   [Y], [N] Defines the reporting delay in seconds for zone 6. UL/ULC: Must be set to “00.” Reports alarms on zone 6 ONLY if the conditional zone (zone 7 in zone trigger mode; zone 4 in 4204 mode; zone 8 in 2-4204 mode) is triggered (armed). If [N], always reports alarms on zone 6. 58 Enable Zn7 Y/N (N)_ Zn7 Trigger Type (V+)_ Invert Zn7 Y/N (N)_  4204 only 4204 only 4204 only [Y], [N]  (EOLR)  (V+)  (V–) [Y], [N] Enables alarm reporting for zone 7, if used. If [N], skip to Prompt 66: "Review." Selects the triggering method for this zone input. Press the [space] key to scroll through choices. Inverts the alarm and normal states of the zone 7 trigger; otherwise uses normal input signal.

46

48



49



[Y], [N]

50



51



54



55 56



[Y], [N]

57

59

60



3-16

Section 3: Programming the GSMV
PROMPTS 61 Restore Zn7 Y/N (Y)_ ZONE TRIG.  4204/ 2-4204  ENTRY OPTIONS [Y], [N] DESCRIPTION Enables restore reporting for zone 7. Zone Trigger mode: This question will only be displayed if zone 7 is not used as the conditional (arming) trigger zone. UL/ULC: Must be set to “Y.” 62 Delay Zn7 (secs) (00)_   [01-15] [00] = no delay Defines the reporting delay in seconds for zone 7. Zone Trigger mode: This question will only be displayed if zone 7 is not used as the conditional (arming) trigger zone. UL/ULC: Must be set to “00.” 63 Rpt Zn7 ONLY if Armed (N)_  [Y], [N] Reports alarms on zone 7 ONLY if the conditional zone (zone 4 in 4204 mode; zone 8 in 2-4204 mode) is triggered (armed). If [N], always reports alarms on zone 7. 2-4204 mode: If any zone is programmed to "Report Only if Armed," or if tamper is enabled, skip to "Review." Enables restore reporting for zone 8. UL/ULC: Must be set to “Y.” [01-15] [00] = no delay [Y] = review [N] = exit Defines the reporting delay in seconds for zone 8. UL/ULC: Must be set to “00.” Reviewing Programming Mode Entries To review the programming options (to ensure that the correct entries have been made), press [Y]. The programming questions are displayed again. Use the up/down arrow keys to scroll through the program fields without changing any of the values. If a value requires change, simply type in the correct value. When the last field is displayed, the “REVIEW?” question again appears. To exit the programming mode, press [N] in response to the "REVIEW?" question, and refer to Exiting Programming Mode below.

64

Restore Zn8 Y/N (Y)_ Delay Zn8 (secs) (00)_ Review? Y/N 

24204 only 24204 only 

[Y], [N]

65

66

Exiting Programming Mode
To exit the programming mode, press [N] in response to the "REVIEW?" question. Then press [Y] to the "Exit Prog Mode?" question. Upon exiting, the message "Checking Root File TX Path" will be displayed, and the configuration file at the server is updated to log the changes made. When complete, the message "DONE" is displayed to indicate the file was successfully uploaded. If critical configuration changes were made, such as the mode of operation, the GSMV will reset to ensure that the programming features are enabled. If the file is not successfully uploaded, one of the following prompts will be displayed. Follow the steps shown below until the upload is successful.

3-17

GSMV/GSMVCN Installation and Setup Guide Display
Cannot Upload Try Again? Y/N_ Failed to Update Root File! Network problem, or you answered "N" to "Cannot Upload Try Again?" prompt.

Description
GSM module is not yet initialized.

What to do
Wait for RSSI LEDs to be lit. Press [Y]. Initiate the Force Server Update command by pressing the [0] key; refer to Section 5: Programmer Keyboard Commands.

Setting Factory Defaults To reset the programming options to factory-default values, press [ESC] at the "Exit Prog Mode?" prompt.
Set Default? Y/N_ Press [Y] to reset factory default values. Press [N] to cancel this function.

If you press [Y], all programmed values are reset to the original factory settings. PLEASE NOTE THAT THIS WILL ERASE ANY PASSWORD THAT MAY HAVE BEEN ENTERED. After pressing [Y], the Create Password prompt appears (see Prompt 4).

3-18

S E C T I O N

4

Registration
                                                

Registering the GSMV
Once you have initialized and programmed the GSMV, it must be registered to enable the account. An unregistered GSMV is indicated on the Status Display as: Status lit, Message slow blinking, and Fault not lit.
STATUS, GREEN MESSAGE, YELLOW FAULT, RED

Figure 4-1. Unregistered GSMV Status Display In Normal Operation Throughout this document, the following key is used to describe LED state:

ON

OFF

FAST BLINK

SLOW BLINK

Figure 4-2. LED Key Upon completion of the registration process, a GSMV transmits a registration message and receives a registration validation indicating that the account is now enabled. Wait for the "Registration Success" message to appear, regardless of the registration method used. You can register the GSMV by one of the following methods:     Through the AlarmNet Direct website Through use of the Tamper Switch Through use of a 7720P Programming Tool By phone

Registering through AlarmNet Direct Website The GSMV can be registered through the AlarmNet Direct Website. To program the module via the website (if you are already signed up for this service), go to: https://services.alarmnet.com/AlarmNetDirect/userlogin.aspx. Log in and follow the on-screen prompts. If you are not signed up for this service, click on “Dealer Signup” from the login screen to gain access to the Honeywell web-based programming. Dealer Sign-Up Direct Link: https://services.alarmnet.com/AlarmNetDirectP_Sign-Up. You will be instructed how to proceed upon completing the sign-up form. Only one sign-up per dealer is required. Once an initial user is established, additional logins may be created by that user. NOTE: Central Stations sign up by contacting AlarmNet Administration at 800-222-6525 option 3. Please have the following information available when programming the device: 1. Primary City ID (two-digit number) 4-1

GSMV/GSMVCN Installation and Setup Guide 2. Primary Central Station ID (two-digit hexadecimal number) 3. Primary Subscriber ID (four-digit number) 4. MAC ID and MAC CRC number (located on outside of box and on label inside module) or MIN number of the device you are replacing. Once module is registered, you may log out of the AlarmNet Direct website. Using the Tamper Switch Initiate the registration sequence by clicking the Tamper Switch three times. You can monitor the registration process by viewing the Status Display. The Message (yellow) LED and the Status (green) LED will blink slowly in unison while registration is in progress. Once the registration has been completed successfully, the GSMV enters normal operating mode; the Status (green) LED goes out and the Message (yellow) LED is lit to indicate that the Power On / Reset message is waiting to be sent. This message will appear at the receiving station as “E339 C08xx”, where “xx” is the ECP device address. The description may read “Trouble – Exp. Mod. Reset”. If registration is not validated within 90 seconds, the GSMV times out, and the (green) LED will be lit (solid). The Power On / Reset message will be sent in Ademco High-Speed format if the module is programmed for zone trigger, 4204 or 2x4204 modes. Using the Programming Tool The interactive registration feature allows the installer to register the GSMV through a series of keyboard commands on the 7720P Programming Tool. This method of registration lets the installer monitor the registration process. Registering … Once the installation is complete, press the [] key on the 7720P. The registration message is sent and the unit waits for the acknowledgment. If this is a new installation and the city, central station, and customer numbers have been correctly entered, the GSMV is registered and this message is displayed. The GSMV is now in full service and available for alarm reporting to the central station.

Registration SUCCESS

Possible Errors Registration BAD Timed Out Registration BAD Pri Sub ID BAD Displayed if no response to the registration request is received. Indicates the city, central station, or customer number for the labeled account(s) is not accepted. The ID information was either entered incorrectly, or the central station failed to pre-authorize programmed ID numbers with AlarmNet customer service. Indicates the city, central station, or customer number for the Secondary account is not accepted. The ID information was either entered incorrectly, or the central station failed to pre-authorize programmed ID numbers with AlarmNet customer service. Displayed when both primary and secondary subscriber IDs are invalid.

Registration BAD 2nd Sub ID BAD

Registration BAD Pri&Sec – IDs BAD

4-2

Section 4: Registration Possible Errors Registration BAD Pri ID – Need PIN Displayed if this is a repair/replacement, or an error was made in programming the Primary account information of GSMV for an existing account. This prompt appears for 2 seconds. See the Replacing an existing module section below for further displays. This prompt is displayed if this is a repair/replacement, or an error was made in programming the Secondary account information of GSMV for an existing account. This prompt appears for 2 seconds. See the Replacing an existing module section below for further displays. This prompt is displayed if this is a repair/replacement, or an error was made in programming BOTH the Primary and Secondary account information of GSMV for an existing account. This prompt appears for 2 seconds. See the Replacing an existing module section below for further displays.

Registration BAD 2nd ID – Need PIN

Registration BAD Pri&2nd – Need PIN

Replacing an existing module using the programming tool Enter PIN# This prompt appears after pressing [Shift] and the down arrow [] on the 7720P. Enter a 4-digit alphanumeric PIN number provided by your central station, your dealer or an authorized AlarmNet representative. Press the [Enter] key. Registering … The registration message is sent and the unit waits for acknowledgement. If the PIN is valid, the new GSMV is registered and the old unit unregistered. Additionally, AlarmNet sends a substitution alarm to the central station. If you entered an invalid PIN, the appropriate message is displayed depending on which account number is being replaced (see above for exact wording). The registration process is repeated. NOTE: Each attempt causes a substitution alarm to be sent to the central station.

Registration SUCCESS Registration BAD

Register by Phone You can register the module by calling the AlarmNet Technical Assistance Center (TAC) at 1-800-222-6525. You will need the following information:  MAC number (found on the label).  Subscriber information (provided by the central station), including a city code, CSID, and a subscriber ID.  When instructed to do so, triple-click the tamper switch to complete the registration.

4-3

GSMV/GSMVCN Installation and Setup Guide

4-4

S E C T I O N

5

Programmer Keyboard Commands
                                                

Programmer Keyboard Commands
Programmer keyboard commands can be used to quickly view your connectivity settings and options. Most commands require you to press the [shift] key and then the designated command key. (See the keys designated in red on the 7720P Programming Tool.) [A] 7845GSM x.x.xx Software Revision mm/dd/yy "x.x.xx" indicates the installed software Revision. Mm/dd/yy indicates month, day and year of the revision. Module Identification Displays [B] MAC xxxxxxxxxxxx MAC CRC yyyy MAC Address “xxxxxxxxxxxx” indicates the GSMV's unique identification number. "yyyy" indicates the MAC CRC number. This number is also found on the label on the module, as well as the label on the box. Press the [Space] key to go to the next field. Press the backspace [BS] key to go to the previous field. SCID xxxxx xxxxx xxxxx xxxxx SCID Display Displays the identification number assigned to the SIM card (SCID) in this device. Press the [Space] key to go to the next field. Press the backspace [BS] key to go to the previous field. IMEI xxxxxxxx xxxxxx x IMEI Display Displays the identification number assigned to the GSM module in this device. Press the [Space] key to get the MAC Address. Press the backspace [BS] key to go to the previous field. [C] Time Retrieves the current date and time from the AlarmNet network in Greenwich Mean Time (GMT). This display confirms that the module is in sync with network.

Mon 01 Jan 2001 05:48:39 am

5-1

GSMV/GSMVCN Installation and Setup Guide GSM Status Displays [E] PriRSSI GPRS REG -xxxdbm x x GSM Status Display Screen 1 PriRSSI – Primary Site RSSI level in dbm GPRS – GPRS Service availability where “x” can be: “Y” if GPRS is available “N” if GPRS is Not available REG – Registration status from radio module where “x” can be: N – Not Registered H – Registered Home S – Searching D – Registration Denied R – Registered Roaming ? – Unknown Registration State Press the [Space] key to go to the next screen. Press the backspace [BS] key to go to the last screen. Cntry Netw LAC xxx xxx xxxxx GSM Status Display Screen 2 Cntry – Country Code Netw – Network Code LAC – Local area code Press the [Space] key to get to the next screen. Press the backspace [BS] key to go to the previous field. Cell BaseSt Chan xxxxx x xxx GSM Status Display Screen 3 Cell – Base Station ID BaseSt – Base Station Antenna Sector Chan – Control Channel in use Press the [Space] key to go to the next screen. Press the backspace [BS] key to go to the previous field. Second Site RSSI -xxxdbm GSM Status Display Screen 4 Secondary GSM Site RSSI level in dBm. Press the [Space] key to go to the GSM Status Display Screen 1. Press the backspace [BS] key to go to the previous field.

System Status Displays [S] ECP 67 TmPB Flt xx 5 ++ OK ECP Mode Displays the zone and system fault status. Press the [Space] key to go to the next field. Press the backspace [BS] key to go to the previous field. 1234 67 TmPB Flt 5555 xx 5 ++ OK 4204 Emulation Mode Displays the zone and system fault status. Press the [Space] key to go to the next field. Press the backspace [BS] key to go to the previous field.

5-2

Section 5: Programmer Keyboard Commands

12345678 TmPB Flt 5555555x 5 ++ OK

Two-4204 Emulation Mode Displays the zone and system fault status. Press the [Space] key to go to the next field. Press the backspace [BS] key to go to the previous field. Zone Trigger Mode The status of the GSMV can be viewed on the 7720P. The status display includes:  Zone input status (1234567) - the numbers 1-7 represent the 7 mappings of the zone input, and follow Honeywell's ADEMCO high-speed format codes: 1 = New Event 5 = Normal X = Not Enabled  Tm – Tamper status follows high-speed format codes above.  P – Represents line voltage as follows: + = Power line voltage OK - = Power line voltage bad and reported V = Power line voltage bad, not reported (reporting window not expired) ^ = Power voltage restored, not yet reported  B – Represents battery condition as follows: + = Battery voltage acceptable - = Battery voltage below 5.7V ±5%  Flt – Represents radio faults: OK = Normal ; No fault G = No network connectivity over GSM and fault time has expired. g = No network connectivity over GSM and fault time has NOT yet expired. NOTE: The 7720P will not operate if the power line voltage is removed. Battery Voltage Display The voltage levels of the battery connected to the GSMV can be viewed on the 7720P. The first line of the display shows the voltage level of the battery with no load. The second line of the display shows loaded battery voltage. An asterisk (*) next to the voltage indicates that this is below the accepted level. Press the [Space] key to go to the next field. Press the backspace [BS] key to go to the previous field.

1234567 TmPB Flt 5555555 5 ++ OK

Bat NLd: x.xxV Bat Ld: x.xxV

5-3

GSMV/GSMVCN Installation and Setup Guide Line Voltage Display The line voltage of the GSMV can be viewed on the 7720P. An asterisk (*) next to the voltage indicates that this is below the accepted level. Press the [Space] key to go back to the System Status Display. Press the backspace [BS] key to go to the previous field. [T] Test Msg Sent Test Alarm Sends a Test alarm to AlarmNet. Functional for a registered GSMV only. If the device is not registered, a message is displayed indicating that the command cannot be executed. NOTE: If two CSIP’s are used, test alarms are sent to each central station. In addition, if the primary fails to report, a second (backup) message is sent to the secondary station. [X] Reset CPU Y/N Reset the GSMV. Pressing [N] returns to normal mode. Pressing [Y] resets the device. []
(UP arrow)

Line Voltage xx.xxV

Registering … Enter PIN#

Registration Registers a programmed GSMV with AlarmNet. Registration with PIN for Replacement Module Registers a replacement GSMV with AlarmNet, once programmed, using the existing PIN #. Force Upload of Configuration File to Server Pressing [Y] will force the device to upload its entire configuration file to the server. Pressing [N] cancels the operation. NOTE: If the GSM module is not initialized when you enter this command, the following screen will be displayed: Cannot Upload Try Later! _ Wait for the RSSI LEDs to light, indicating the GSM module has completed its initialization, and try again.

[]
(DN arrow)

[0]

Force Server Update? Y/N

[ENTER]

Strt Prog Mode? Y/N_

Enter Program Mode Press [Y] to enter program mode; otherwise, press [N].

5-4

Appendices
                                                

Appendix A: Summary of LED Operation
Status Display Operation The Status Display has three LEDs used to indicate message and device status:  STATUS, green  MESSAGE, yellow  FAULT, red

GREEN (STATUS) YELLOW (MESSAGE) RED (FAULT)

7845i-GSM-012-V0

Figure A-1. Status Display LEDs with Front Cover Installed Each LED can have four different states - ON, OFF, FAST BLINK and SLOW BLINK. Throughout this document, the following key is used to describe LED state:

ON

OFF

FAST BLINK

SLOW BLINK

Figure A-2. LED Key

A-1

GSMV/GSMVCN Installation and Setup Guide Table A-1. Status Display Operation
LED COLOR GREEN LED STATUS DESCRIPTION ON – GSMV is NOT registered with AlarmNet. OFF – GSMV is registered with AlarmNet. FAST BLINK – Download session with Compass in progress. SLOW BLINK – In unison with yellow LED – Registration in progress. ON – Message transmission pending. QUICK PERIODIC BLINK - Normal FAST BLINK – Message waiting for network ACK. SLOW BLINK – Idle, power abnormal. – In unison with green LED – Registration in progress. ON – No contact with network. OFF– Normal. SLOW BLINK – Loss of communication with the panel (ECP fault). FAST BLINK – No network contact AND loss of communication with the panel. FAST BLINK – In unison with the RSSI Bar Graph LEDs – Hardware Error. Call the AlarmNet Technical Assistance Center.

YELLOW

MESSAGE

RED

FAULT

ALL

A
STATUS, GREEN MESSAGE, YELLOW FAULT, RED STATUS, GREEN MESSAGE, YELLOW FAULT, RED

B

Figure A-3. A Registered GSMV Status Display (A) and an Unregistered GSMV Status Display in Normal Operating State(B)

1 STATUS, GREEN MESSAGE, YELLOW FAULT, RED

2

3

4

Figure A-4. LED Sequence for a Registered GSMV Message Transmission

A-2

Appendices Signal Strength (RSSI) / Mode and Status LEDs The Signal Strength (RSSI) / Mode and Status LEDs normally display the module’s signal strength. LED 1 (red LED on the left) will be lit to indicate that the display is in RSSI mode, and the other LEDs indicate signal strength (lowest to highest, from left to right) between the module and the receiving tower.  The signal strength RSSI LEDs will indicate regardless of whether the SIM is activated. (If the SIM is not activated, the red FAULT LED will be lit).  This allows you to immediately determine if the desired mounting location has sufficient signal strength for proper operation.  If the SIM is not activated, you can determine the signal strength by simultaneously pressing the MODE and TAMPER buttons. For proper operation, look for at least 3 bars lit solid. RSSI Display

3 BARS MIN.

R

Y

Y

G

G

G
7845i-GSM-025-V0

NOTE: The module still must be activated and registered to transmit messages to AlarmNet and your central station. Mode and Status Indicator Switch Press and hold the Mode and Status Indicator Switch to change the LED functions in order to view the mode of operation and network carrier status. When the switch is held down, LED 1 (red LED on the left) will be off, and the LEDs from left to right have the following meanings: Table A-2. LED Functions with Mode and Status Indicator Switch Depressed Operation Modes (Table A-3) Status Indications (Table A-4)

LED 1 (red)
Off=Mode and Status indicator

LED 2 (yellow)
Operation Mode (in combination with LED 3)

LED 3 (yellow)
Operation Mode (in combination with LED 2)

LED 4 (green)
Not Used

LED 5 (green)
GPRS Service

LED 6 (green)
GSM Module Registration with Network Carrier

See below for specific modes and status indications. Table A-3. Operation Modes OPERATION MODE ECP Zone 4204 2 - 4204 LED 2 (1st yellow)
OFF ON OFF ON

LED 3 (2nd yellow)
OFF OFF ON ON

A-3

GSMV/GSMVCN Installation and Setup Guide Table A-4. Status Indications STATUS
OFF SLOW BLINK NORMAL BLINK FAST BLINK ON

LED 4 (1st green)
Normal – –

LED 5 (2nd green)
No GPRS service available – –

LED 6 (3rd green)
GSM module not registered with network carrier GSM module registered—second site available–low signal strength GSM module registered—second site available–acceptable signal strength GSM module registered—second site available–excellent signal strength GSM module registered—no second site available

– Not Used

GPRS in use by device GPRS service available

A-4

Appendix B: Central Station Messages
The following messages are sent by the GSMV module for the conditions listed below. Table A-5. GSMV Central Station Messages Alarm Condition Power On / Reset Tamper Power Loss Low Battery Battery Charger Failure ECP Supervision Communication Path Supervision Swinger Suppression Telco Open/Close Test * xx = GSMV Device Address The control panel sends its own general code (E353) for a trouble condition. 5555 5555 9 ECP Mode Alarm Code E339 C08xx* E341 C08xx* E337 C08xx* E338 C08xx* E314 C08xx* E355 C0000 ECP Mode Restore Code Zone and 4204 Modes Alarm Code 5551 5555 6 5555 5551 7 1555 5555 6 5155 5555 6 5155 5555 1 5555 5515 5 Zone and 4204 Modes Restore Code 5555 5553 7 3555 5555 6 5355 5555 6 5355 5555 1 5555 5535 5 5555 5553 5 0D00 0005 0 5555 5155 6 2 sent in selected zone 5555 5555 9 5555 5355 6 4 sent in selected zone

R341 C08xx* R337 C08xx* R338 C08xx* R314 C08xx* R355 C0000 R350 C0951

B-1

GSMV/GSMVCN Installation and Setup Guide

B-2

Appendix C: GSM Downloading
General Information The GSMV can be used to provide high-speed up/downloading to Honeywell VISTA control panels over the Internet (via the GPRS network). This allows site maintenance independent of central station monitoring, and modification to sites globally. At this time, some control panels support downloading through the ECP bus and some panels support downloading through the use of a Direct Wire connection. Residential panels such as the VISTA-20P support ECP downloading. Currently, control panels such as VISTA-128BP and FBP support downloading through use of a Direct Wire connection (using the trigger connections on the control panel).

UL

Downloading may only be performed if a technician is at the site.

Direct Wire Setup To perform up/downloading using Direct Wire, the GSMV requires that Direct Wire Downloading is enabled (Direct Wire Y/N), and that the ECP device address on which the GSMV communicates with the control panel as a keypad is entered (Keypad Address). Additionally, the GSMV must be connected by cable as shown below to the panels listed. NOTES: 1. For Direct Wire IP downloading control panels (e.g. VISTA-128FBP, FA1700C), Program Field 3*19 Enable J2 Header Printer Port must be set to "1". 2. This feature is not available if device is set for zone trigger mode.
VISTA-128BP/250BP FA1660C J8 CONNECTOR COMMUNICATIONS MODULE
1 2 3 4
NU

5

6

7

8

9

PROGRAMMER PORT WHITE BLUE K4668WH RJ 11 CABLE
TB 1
1 2 3 4 5 6 7 8 9 10 11

FOR EXTERNAL ANTENNA 50 OHM, MMCX ONLY

OUT 5 (GREEN)

OUT 6 (BROWN)

(BLUE)

(RED)

PRINTER DTR

GROUND

GROUND

GROUND (BLACK)

IN 3 (YELLOW)

IN 2 (VIOLET)

(GREY)

Honeywell
GSM GPPS WEB MODE 2 MODE 1 RSSI

4142 TR CABLE

PARTS SUPPLIED WITH DOWNLOADER KIT P/N VBPCOMKIT
VISTA-128FBP/250FBP FA1670C/FA1700C J2 CONNECTOR
1 2 3 4 5 6 7 8 9

COMMUNICATIONS MODULE
(BROWN) (GREEN) (WHITE) (GRAY)

OUT 1 (YELLOW)

(VIOLET)

(BLACK)

(BLUE)

(RED)

PROGRAMMER PORT
4100SM
TO AUX PWR 1 OUTPUT + (TO TERM 11) - (TO TERM 12)
8 7 6 5 4 3

FOR EXTERNAL ANTENNA 50 OHM, MMCX ONLY

+ PWR - (GND) RXD not used not used TXD not used not used
TB 1
1 2 3 4 5 6 7 8 9 10 11

GROUND

INPUT 1

OUT 6

OUT 4

OUT 7

OUT 3

OUT 2

OUT 5

Honeywell
GSM GPPS WEB MODE 2 MODE 1 RSSI

4142 TR CABLE

2 1

RED BLUE WHITE

PARTS SUPPLIED WITH DOWNLOADER KIT P/N VBPCOMKIT K14394LF 25-PIN TO RJ11 CABLE

Figure C-1. Cable Connections for Direct Wire Downloading C-1

iGSMBR-018-V0

iGSMBR-017-V0

GSMV/GSMVCN Installation and Setup Guide

C-2

Appendix D: Glossary
AES – Advanced Encryption Standard DHCP – Dynamic Host Configuration Protocol, which provides a mechanism for allocating IP addresses dynamically so that addresses can be reused when hosts no longer need them. DNS – Domain Name System, which is a distributed hierarchical naming system used to resolve domain names (e.g., www.yahoo.com) into numerical IP addresses (e.g., 204.17.25.1.). DSL – Digital Subscriber Line ECP – Enhanced Console Protocol, which is a proprietary communications bus used in Honeywell VISTA control panels for wiring additional keypads and peripheral devices; consists of a four-wire data bus (power+/-, data in/out). Gateway IP Address – A gateway (sometimes called a router) is a computer and/or software used to connect two or more networks (including incompatible networks) and translates information from one network to the other. The Gateway IP address is the IP address for the gateway. GPRS – (General Packet Radio Service) GSM – Global System for Mobile communications, which is an international standard for digital mobile phone systems used for cellular communication. IMEI – International Mobile Equipment Identity number IP – Internet Protocol IP Address – A unique number consisting of four parts separated by periods, sometimes called a "dotted quad.," for example: 204.17.29.11, assigned to every computer/workstation connected to the Internet. IP numbers can be "static" (assigned and unchanging) or "dynamic," assigned via DHCP at each and every startup. ISDN – Integrated Services Digital Network ISP – Internet Service Provider LAN – Local Area Network MAC ID – Media Access Code; located on the module label. PPPoE – Point-to-Point Protocol over Ethernet Subnet Mask – A Subnet is a portion of a network that shares a network address with other portions of the network, and is distinguished by a subnet number. The Subnet Mask is a 32bit address mask used in IP to indicate the bits of an IP address that are being used for the subnet address. TCP/IP – Transmission Control Protocol / Internet protocol

D-1

GSMV/GSMVCN Installation and Setup Guide

D-2

NOTES

NOTES

GSMV Summary of Connections
INTERNAL ANTENNA

STATUS LED MESSAGE LED FAULT LED
FOR EXTERNAL ANTENNA 50 OHM MMCX ONLY

MOUNTING HOLE (TYP.)

7720P PROGRAMMER PORT/ PANEL DOWNLOAD PORT TB 1 1 2 3 4 5 6 7 8 9 10 11 1

PRIMARY POWER: 9 - 16.5 VAC CURRENT: 900mA PEAK, 70mA STANDBY BATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP

FCC:XXXXXXXXXX

IC: YYYYYYYYYY

AC 1 AC 2 NOT USED or 12V DC IN GND ZONE INPUT Z1/Z2 or ECP INPUT ZONE INPUT Z3 or ECP OUTPUT ZONE INPUT Z4 or NOT USED ZONE INPUT Z5 or NOT USED ZONE INPUT Z6 or NOT USED ZONE INPUT Z7 or NOT USED FAULT OUTPUT MOUNTING HOLE CONNECTOR FOR USE WITH DCID ONLY

BLACK

RED

SIGNAL STRENGTH (RSSI)/MODE AND STATUS LEDs

GPRS

RSSI

IBS

M1 M0

MOUNTING HOLE (UNDER BATTERY)
BLK RED

BATTERY CLIP

BATTERY TAMPER SWITCH J1 BATTERY CONNECTOR SIGNAL STRENGTH (RSSI)/ MODE AND STATUS INDICATOR SWITCH SCREW
7845GSM-006-V0

TB1 Wiring for GSMV Cellular Communicator TB1 1 2 3 4 5 6 7 8 9 10 11 ECP Mode AC 1 AC 2 ECP V+ (RED) GND (BLK) ECP IN (YEL) ECP OUT (GRN) NOT USED NOT USED Z6 Z7 FLT OUT Zone Trigger Mode AC 1 AC 2 NOT USED GND (BLK) Z1/Z2 Z3 Z4 Z5 Z6 Z7 FLT OUT 4204 Mode AC 1 AC 2 ECP V+ (RED) GND (BLK) ECP IN (YEL) ECP OUT (GRN) NOT USED NOT USED Z6 Z7 FLT OUT Two – 4204 Mode AC 1 AC 2 ECP V (RED)+ GND (BLK) ECP IN (YEL) ECP OUT (GRN) NOT USED NOT USED NOT USED NOT USED FLT OUT

FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help.

DOCUMENTATION AND ONLINE SUPPORT For the latest documentation and online support information, please go to: http://www.security.honeywell.com/hsc/resources/MyWebTech/

WARRANTY For the latest warranty information, please go to: http://www.security.honeywell.com/hsc/resources/wa/

2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 Copyright  2010 Honeywell International Inc.

www.honeywell.com/security

Ê800-07349eŠ
800-07349 8/10 Rev. A