Honeywell Home 269SN - Installation and Setup Guide Dated 4/03

K0400V1D 4/03 Rev D
269SN
Holdup
Switch
Installation and Setup Guide
GENERAL INFORMATION
   
 
 !"   #  
$ 
% %&     
 
 $'# ( 
  
) % &   $ #
&  
 % % # 
   
%$
*  %(
  
+%        #$ ,     +
% &% )
)  %)%  ,-./01&)2
345$
SUPERVISION
' %&& (&6# % 
  
 &$' %& & (&6#
 % 
 %  ) $
PROGRAMMING
7 %%&0    * 
  
8   && $
 &   + %  9 (      
  &
  :        $ .  

 &  &  9  &&;
<=1 .> .?@<A?3 7 
<* B> .?@<A?C–  &) C 
-#
MOUNTING
7    %
 & 
  $
1.
*E ( #  #  

# $
2.
7 &     #(
 
 )+ 5$
3.
' # 3( )# 

 %$
*/ 17, F
*/ 17, F*/ 17, F
*/ 17, F* %  !"

 #    ) (% &

   ) ( 
& 
  $*(&   
 
   $
4.
 #   $
!G6H
 $I   
$ 
    # 
 $
*/ 17, ;
*/ 17, ;*/ 17, ;
*/ 17, ; # & (  
#
 #$
5.
 )+ & ) +

)+  #    #&

 $
*/ 17, ;
*/ 17, ;*/ 17, ;
*/ 17, ; ) + #   
&  % &) %    

  $ #&)& %&  

  $
6.
B  & (  6? 
& 
  &  4$
7.
&)   # #
 
   $!563  
4$

Figure 1
Figure 2
+
+
MOUNTING
HOLE
TRIGGER
RESET KEY
(K4563
SUPPLIED)
COVER
SCREW
(2)
No. 6x7/8
PROTECTIVE
STEEL
COVER
CIRCUIT
BOARD
COVER
ATTACH HOLE
COVER
ATTACH
HOLE
MOUNTING
SCREW
(2)
No. 6X1 3/4
COVER
SCREW
COVER
269SN-001-V1
MOUNTING
HOLE
TRIGGER
ASSEMBLY
TO CONVERT TO MOMENTARY (NO LATCHING) SWITCH
OPERATION, REMOVE THE TRIGGER ASSEMBLY FROM THE
CASE. USING A PAIR OF CUTTERS, CUT THE TRIGGER LATCH
AT THE POINT THE "ARROW" IS STAMPED ON THE CASE.
TRIGGER
LATCH
ARROW
(CUT POINT)
269SN-003-V0
Figure 3
Figure 4
Figure 5
TO THE INSTALLER
Regular maintenance and inspection (at least annual
ly) by
the installer and frequent testing by the user are
vital to
continuous satisfactory operation of any alarm syst
em.
The installer should assume the responsibility of d
eveloping
and offering a regular maintenance program to the u
ser, as well
as acquainting the user with the proper operation a
nd
limitations of the alarm system and its component p
arts.
Recommendations must be included for a specific pro
gram of
frequent testing (at least weekly) to ensure the sy
stem's
operation at all times.
WARRANTY INFORMATION
For the latest warranty information, please go to:
www.resideo.com
SPECIFICATIONS

%
% %
% 


J'!56J !63J-

4&&!H&&!5&&
. 
.  . 
.  



/  ! %
$A&,(/,K
0;
;;
;



1
11
1


5° °

&;
&;&;
&;


A°0 4A°0

,%;
,%;,%;
,%;


BC5–  & 

%&
7
77
7

2%;
2%;2%;
2%;


  (  &)2345 

  %

2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
© 2020 Resideo Technologies, Inc.
www.resideo.com
K0400V1D 4/03 Rev D
ROUTE THE WIRE THROUGH THE WIRE ENTRY HOLE.
STRIP 6MM (.24 INCH) OFF THE WIRE ENDS.
269SN-004-V0
TERM. ASSIGNMENT
269SN-002-V0
POLLING LOOP
TERMINALS ON
CONTROL
1 (+) POLLING LOOP (+)
2 ( ) POLLING LOOP ( )
POLLING LOOP
ALWAYS OBSERVE POLARITY.
ALWAYS CONNECT IN PARALLEL.
MOUNTING
SCREW (2)
No. 6X1 3/4
(SUPPLIED)
269SN-009-V1
MOUNTING
HOLE
MOUNTING
HOLE
IMPORTANT:
THIS DEVICE MUST
BE PERMANENTLY
MOUNTED WITH THE
SCREWS SUPPLIED
HOLDUP SWITCH SHOWN MOUNTED
IN TYPICAL UNDER COUNTER APPLICATION
C
US
US
R
LISTED
of 2

Related Products

Honeywell Home 269SN - V-Plex Hold-Up Switch Stainless Steel
Honeywell Home 269SN
V-Plex Hold-Up Switch Stainless Steel
List Price:
Our Price: $54.99

Document Transcript


K0400V1D 4/03 Rev D


269SN

Holdup

Switch


Installation and Setup Guide
GENERAL INFORMATION

!"
#

$

%%&

$'#
(

)%&$
#
&

%%#

%$
*
%(

+%

#$ ,

+
% &% )
)
%)%
,-./01&)2
345$
SUPERVISION
'%&&
(&6#%

&$'%&
&
(&6#
%
%)$
PROGRAMMING
7%%&0 *

8
&&$
& + % 9(

&
:

$ .

&&
9&&;
<=1 .> .?@ .?@

Uploaded