Honeywell Home 4190SN - Installation and Setup Guide Dated 2/09



Related Products

Honeywell Home 4190SN - V-Plex 2-Zone Remote Point Module
Honeywell Home 4190SN
2-Zone, V-Plex Expansion Module
List Price:
Our Price: $10,000.00

Document Transcript


N6450-1V1B 2/09 Rev. B
ADEMCO 4190SN

V-Plex
®
Two-Zone (SIM)

Serialized Interface Module

Installation and Setup Guide

General Information
The ADEMCO 4190SN V-Plex
®
is a 2-zone
expander, which allows use of the available
expansion zones provided by controls that
support V-Plex
loop devices. The
4190SN
consists of two protection loops, known as
the left (primary) and right (secondary)
loops.
The left loop can be used for:


closed-circuit devices, with or with out
EOLR supervision


open-circuit devices with EOLR
supervision


fast-response (10 millisecond) devices.
Follow the chart to the right for cutting the
correct jumpers and choosing the correct
resistor when using the left loop.

The right loop can be used for:


closed-circuit devices only


has no EOLR supervision


400 millisecond response time.
The jumpers do not affect the operation of
the right loop. The right loop cannot be
used alone.

Supervision
The tamper/supervision response of the
4190SN is determined by the zone response
type assigned to the left loop zone. While
the system is armed, tamper/supervisory
faults will report as alarms if the left loop
zone is assigned a burglary response type
and will report as troubles if the left loop
zone is assigned a non-burglary response
type (i.e., fire, panic, aux).
While the system is disarmed, tamper/
supervisory will always report as troubles.

Programming Notes

Program the unit like any other zone,
according to the alarm control’s installation
instructions. Enter the following
information when prompted for in
programming:
“INPUT TYPE” = “6” (SL—Serial
Number Device)
Left Zone = Loop 1
Right Zone = Loop 2

JUMPERS
USAGE (APPLIES TO
LEFT ZONE – LOOP 1
ONLY)
RED
Cut for fast response
(10msec)
BLUE
Cut for use with no
EOLR (closed-circuit
only). Doing this
automatically puts an
internal 10K ohm resistor
in series with the zone.
NONE CUT
Use the 10K ohm
resistor provided, with
switches in either an
open-circuit or closed
circuit configuration. The
4190SN draws 2mA from
the V-Plex loop in this
mode.



4190SN
TAMPER PINS
(SHORTENED WHEN
COVER IS IN PLACE)
MOUNTING
HOLES (3)
BLUE
JUMPER
TERMINAL ASSIGNMENT
1 (+) POLLING LOOP (+)
2 (-) POLLING LOOP (-)
3 (+) LEFT LOOP 1 (+)
4 (-) COMMON (-)
5 (+) RIGHT LOOP 2 (+)
RPM
+
+
RPM
+
-
ALWAYS OBSERVE POLARITY.
ALWAYS CONNECT IN PARALLEL.
SEE TEXT FOR WIRE GUAGE AND WIRE LENGTH LIMITS.
-
-
RIGHT LOOP (LOOP 2): FOR N.C. SERIES CIRCUITS
ONLY. USE SEALED (REED) CONTACTS. SEE NOTE 1.
RIGHT LOOP NOT SUPERVISED. SEE UL NOTE 2 BELOW.
LEFT LOOP (LOOP 1): FOR N.C. CIRCUIT (INTERNAL EOLR)
OR N.C. AND/OR N.O. CIRCUIT (EXTERNAL EOLR). SEE
NOTES 2 AND 3. LEFT LOOP SUPERVISED. CLASS B, STYLE B.
SERIAL # ID
4190SN-001-V1
POLLING LOOP - SUPERVISED CLASS B, STYLE 4
CIRCUIT, 25 OHM MAX LINE IMPEDANCE
POLLING LOOP
TERMINALS ON
CONTROL
RED
JUMPER

UL Notes
1.

!
"#!"$
%
#!
&'
%

2.

( )

#

*
3.

##

*+*(*
(,- .(
/
01+#

21+3*
4.

#

*+*
**
(* (,
21+3((
*
5.

4(5
*
6.

#

*
7.

65
(*

(

(
*

Specifications

Physical:
7
&58"9-$'.
%

'589-".
6(

9-&$.

Electrical:
:;("–&:6
6&4

/=*(73>
7?"5&&47?
/=*(;(
'
=*
31#13+%1;
44;+

;
3;+
#+3%1+
3+
@4
17;%7%;%%161:;1;
16!#+3614; +

;/;4;+
+#%11
;31
443/ A 1/*

#@45B&(

For the latest warranty information,
please go to:
www.resideo.com


ÊN6450-1V1BÆŠ

N6450-1V1B 2/09 Rev. B


2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
© 2020 Resideo Technologies, Inc.
www.resideo.com


Uploaded