Honeywell Home PROLTE-A & PROLTE-V Installation Instructions - Dated 3/19 Rev. A

PROLTE Series Wireless

Communication Modules


Installation and Setup Guide
General Information
The Communication Modules allow the control panel t
o communicate with the Central Station via the cell
ular radio network. The
PROLTE Series includes the following models:
PROLTE-A (US/Canada, AT&T Network)
PROLTE-V (US, Verizon network)
PROTLTE-CN (Canada, Bell network)
The
PROLTE Series
wireless communications module is intended to prov
ide compatible PRO Series control panels with a cel
lular

connection with the central monitoring station. The
module connects directly to the control panel and
is powered via the control panel’s
connection.
Compatible Control Panels:
PROA7PLUS Series – Quick Installation Guide P/N

800-25079 or higher
.
PROH8PLUS Series - Quick Installation Guide

P/N

800-25093 or higher.
Installing the Module in the PROA7PLUS Series
!

Ensure that all electrical power is removed from th
e control before installing the module. Unplug the
power supply and disconnect the backup battery.
1. Affix the provided FCC/IC label (P/N 800-25167 f
or
the PROLTE-A, 800-25168 for the PROLTE-V OR
800-25170 for the PROLTE-CN) on the control’s case
back (refer to Figure 1).
2. If the Control Panel is not powered up proceed t
o
step 7. If the Control Panel is powered up, disarm
the
system and wait 30-60 seconds:
3. Unplug the power supply.
4. Remove the screw securing the control to the wal
l or
desk mount.
5. Remove the control from the wall or desk mount.
6. Disconnect the battery.
QS-061-V0
CONTAINS MODULE:
FCC ID: RI7LE910NAV2
IC:5131A-LE910NAV2
CONTAINS MODULE:
FCC ID: RI7LE910NAV2
IC:5131A-LE910NAV2
CONTAINS MODULE:
FCC ID: RI7LE910SVV2
OR
ADEMCO INC. PROA7PLUS SERIES
FCC / ISED STATEMENT
This device complies with Part 15 of the FCC Rules,
and ISED’s license-exempt RSSs. Operation is subjec
t
to the following two conditions: (1) This Device ma
y
not cause harmful interference. (2) This device mus
t
accept any interference received, including
interference that may cause undesired operation.
FCC ID: CFS8DL-GRIPAIO7
IC: 573F-GRIPAIO7 HVIN: GRIPAIO7

Figure 1. FCC/IC Label Location

7. Remove the left side from the control.
8. Insert the PROLTE Series module into the slot on
the
left side of the control as shown in Figure 2 and
ensure the receptacle is securely seated on the
control’s edge connector.
9. Secure with the screw.
10. Install the left side cover.
11. Connect the battery.
12. Install the control on the wall or desk mount.
13. Plug the power supply into a 24-hour, 110VAC
unswitched outlet.

PROLTE-SERIES
MODULE
COVER
MACHINE
SCREW
QS-057-V0
EXT
INT

Figure 2. Installing the PROLTE Module

Installing the Module in the PROH8PLUS Series
!

Ensure that all electrical power is removed from th
e control before installing the module. Unplug the
power supply and disconnect the backup battery and
earth ground.
1. Affix the provided FCC/IC label (P/N 800-25167
for the PROLTE-A, 800-25168 for the PROLTE-V
OR 800-25170 for the PROLTE-CN) on the
PROH8PLUS cabinet (refer to Figure 3).
2. If the Control Panel is not powered up proceed t
o
step 5. If the Control Panel is powered up, disarm
the system and wait 30-60 seconds:
3. Unplug the power supply.
4. Disconnect the battery.


Ensure that all electrical power is
removed from the control panel
before installing the module. Unplug
the power supply and disconnect the
backup battery and earth ground.

BATT+ BATT -
AUX/BELL_OC LED
RUN LED
IB2/ACTIVE LED
RESERVED LED
TRIGGER 2
12V
GND
TRIGGER 1
BATTERY POWER LED
NOT
USED
HI
LO
ZONE 2
2000
OHMS
EOLR
ZONE 1
USE FOR
2-WIRE SMOKE
DETECTORS
MAXIMUM
NUMBER OF
2-WIRE SMOKE
DETECTORS
ON ZONE 1
IS 16
ZONE 1
2000
OHMS
EOLR
HI
HI
LO
LO
HI
LO
2000
OHMS
EOLR
ZONE 3
2000
OHMS
EOLR
ZONE 4
HI
HI
LO
LO
2000
OHMS
EOLR
ZONE 5
2000
OHMS
EOLR
ZONE 6
HI
HI
LO
LO
2000
OHMS
EOLR
ZONE 7
2000
OHMS
EOLR
ZONE 8
EARTH
GROUND
300-10211
13.5 VDC, 1.8A
POWER
SUPPLY TO
10VAC
UNSWITCHED
OUTLET
(24HR)
DC+
DC -
DC+
DC -
ADTHYBWL-Series - Summary of Connections
800-24129 2/18 Rev.A
RJ-45
CONNECTOR
TAMPER
SWITCH
BLACK
RED
RECHARGEABLE BATTERY
(12V, 7AH)
SEALED LEAD ACID TYPE
SEE
INSTRUCTIONS**
FOR PROPER
GROUNDING
TO INTERNET
CONNECTION
© 2018 ADT Security Services
GND
AUX
SLOT 3
GENERAL
SLOT 2
WiFi / ZWAVE
SLOT 1
LTE
8-PIN TRIGGER
CONNECTOR
AC POWER LED
TRIGGER OUTPUT 1: 100mA MAX
TRIGGER OUTPUT 2: 100mA MAX
AUX OUTPUT LED
NOT
USED
24-HR BATTERY
STANDBY REQUIRED
FOR FIRE
INSTALLATIONS.
USE 12V, 7AH
BATTERY FOR
120mA AUX POWER.
SEE INSTRUCTIONS.
BATTERY CAPACITY FOR EMERGENCY
BURGLARY STANDBY USE AT LEAST
4 HRS.
CHARGING VOLTAGE 13.8VDC.
MAXIMUM CHARGING CURRENT
650mA.
SEALED LEAD-ACID TYPE. BATTERY
NORMALLY NEED NOT BE REPLACED
FOR AT LEAST THREE YEARS
TO DETERMINE TOTAL STANDBY LOAD
ON BATTERY, ADD 100mA TO TOTAL OF
AUX. POWER AND REMOTE TOUCHPAD
CURRENTS
WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM. IN ADDITION, THIS
SYSTEM MUST BE CHECKED BY A QUALIFIED TECHNICIAN AT LEAST ONCE EVERY THREE (3) YEARS.
BLACK: TOUCHPAD GND (-) RETURN
YELLOW: TOUCHPAD IB2A
GREEN: TOUCHPAD IB2B
RED: TOUCHPAD POWER (+)
AUX. PWR
OUTPUT
10.5-13.8VDC
200mA MAX.
(120mA MAX.
FOR UL
INSTALLATIONS)
ALL OUTPUTS
ARE POWER
LIMITED.
}
CONNECTION OF
THE FIRE ALARM
SIGNAL TO A FIRE
ALARM HEAD-
QUARTERS OR
CENTRAL STATION
SHALL BE PERMIT-
TED ONLY WITH
THE PERMISSION
OF THE LOCAL
AUTHORITY HAVING
JURIDICTION. THE
BURGLAR ALARM
SIGNAL SHALL NOT
BE CONNECTED
TO A POLICE
EMERGENCY
NUMBER
THIS EQUIPMENT
SHOULD BE
INSTALLED
IN ACCORDANCE
WITH THE NATIONAL
FIRE PROTECTION
ASSOCIATION'S
STANDARD 72
(NATIONAL FIRE
PROTECTION
ASSOCIATION,
BATTERYMARCH
PARK, QUINCY,
MA 02169). PRINTED
INFORMATION
DESCRIBING
INSTALLATION,
TESTING,
MAINTENANCE,
EVACUATION
PLANNING AND
REPAIR SERVICE IS
TO BE PROVIDED
WITH THIS
EQUIPMENT.
820 OHMS
EOLR
ALARM
OUTPUT
10.5–13.8VDC,
2A MAX. (600mA
MAX. FOR UL
USAGE, INCLUDING
AUX POWER)
STEADY FOR
BURGLARY/PANIC,
TEMPORAL PULSE
SOUNDING FOR FIRE.
USE 702 SIREN, OR
12V BELL. SEE
INSTRUCTIONS.
FOR BELL
SUPERVISION, AND
CONNECT RESISTOR
DIRECTLY ACROSS
EXTERNAL SOUNDER.
WTP100
TOUCHPAD
1501 Yamato Road
Boca Raton, Florida 33431
A L A R M
S TAT U S
CANCEL
PA N I C
O F F
C O D E
C H I M E
I N S TA N T
R E A DY
T E S T
B Y PA S S
M A X
STAY
AWAY
2
3
1
5
6
4
8
9
7
0
#
T RO U B L E
** FOR COMPLETE INFORMATION SEE INSTRUCTIONS 800-24126 OR HIGHER
-
+
A
B
MAX. ZONE RESISTANCE: (EACH ZONE) 300 OHMS (PLUS EOLR)
(USE EOLR PART NUMBER P4100 PART OF KIT SAHDWR1)
ASSEMBLED IN MEXICO
ETL Listed
Household Fire
and Burglar
Warning Unit
800-21465 10/15 Rev.A
3091091
Conforms to UL STD 985, 1023, 1635
Classified to ANSI/SIA CP01-2010
Model LCP500-L
800-24232 3/18 Rev A
HONEYWELL GRIP HYBRID CONTROLLER
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two conditions:
(1) This Device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
FCC ID: CFS8DL-GRIPH
IC: 573F-GRIPH
HVIN: GRIPH
For Patent Information see: www.honeywell.com/paten
ts
Country of Origin: Mexico
PROH8-060-005-V0
CONTAINS MODULE:
FCC ID: RI7LE910NAV2
IC:5131A-LE910NAV2
CONTAINS MODULE:
FCC ID: RI7LE910NAV2
IC:5131A-LE910NAV2
CONTAINS MODULE:
FCC ID: RI7LE910SVV2
OR

Figure 3. FCC/IC Label Location

5. Install the PROLTE Series module on the edge
connector on the PCB (refer to Figure 4). Ensure
the receptacle is securely seated on the edge
connector.
6. Install the retainer and secure the module with
the provided screw.
7. Reconnect the battery.
8. Plug the power supply into a 24-hour, 110VAC
unswitched outlet.
PROLTE
MODULE
PROH8-060-004-V0
GENER
AL
WiFi
BATT+ GND
LTE
TX
RX GND
TX
RX GND
EXT
INT
RETAINER
SCREW

Figure 4. Installing the PROLTE Module



Programming
1. Programming associated with the PROLTE Series mo
dule is accomplished, as part of the control panel
programming. Refer to the
control panel installation and setup guide for addi
tional information.
2. When programming is complete, perform a Communic
ations Test. Using an External Antenna
If adequate signal strength cannot be achieved with
the internal antenna, an external antenna can be e
mployed. An PROLTE-ANT kit
with an adapter cable, clamp, and bracket will be r
equired. A connection diagram with the adapter kit
and a typical antenna is provided
with the kit.

IMPORTANT NOTE ABOUT EXTERNAL ANTENNAS
If an external cellular radio antenna is used, the
antenna may be installed or replaced ONLY by a prof
essional installer.

To the Installer
PROLTE-A: The external antenna gain shall not excee
d 6.63 dBi for 700MHz and 850MHz, 6.0 dBi for 1700M
Hz and 8.5 dBi for
1900MHz. Under no conditions may an antenna gain be
used that would exceed the ERP and EIRP power limi
ts as specified in FCC
Parts 22H, 24E and 27.
PROLTE-V: The external antenna gain shall not excee
d 6.94 dBi for 700MHz, 6.0 dBi for 1700MHz and 9.01
dBi for 1900MHz. Under no
conditions may an antenna gain be used that would e
xceed the ERP and EIRP power limits as specified in
FCC Parts 22H, 24E and 27.
PROLTE-CN: The external antenna gain shall not exce
ed 6.63 dBi for 700MHz and 850MHz, 6.0 dBi for 1700
MHz and 8.51 dBi for
1900MHz. Under no conditions may an antenna gain be
used that would exceed the ERP and EIRP power limi
ts as specified IC RSS-
130, RSS-132, RSS-133, and RSS-139.

Specifications
PROLTE-A
PROLTE-V
PROLTE-CN
Board Dimensions
: .............................. 1.625” W x 2.625”
L x 0.3125” D
Current Drain
: Idle ............................ 30mA, standby

Transmit .................... 490mA, max transmit
Input Voltage:
..................................... 5V (provide
d by the control panel)
Environmental
Operating Temperature: ........................ -10
°F (-23°C) to 131°F (55°C) (for compliance agency 3
2°F (0°C) to 120°F (49°C)
Storage Temperature: ........................... -4
0°F (-40°C) to 158°F (70°C)
Humidity: .........................................
...... 10 to 90% relative humidity, non-condensing
(for compliance agency 0% to 85%)
Antenna
................................................ P
enta-Band diversity antennas for LTE Supports LTE B
ands 12, 13, 5, 4 and 2
External Antenna Kit
: .......................... PROLTE-ANT


FEDERAL COMMUNICATIONS COMMISSION ISED STATEMENTS
The user shall not make any changes or modification
s to the equipment unless authorized by the Install
ation Instructions or User's Manual. Unauthorized
changes or modifications could void the user's auth
ority to operate the equipment.
FCC CLASS B STATEMENT
This equipment has been tested to FCC requirements
and has been found acceptable for use. The FCC requ
ires the following statement for your
information:
This equipment generates and uses radio frequency e
nergy and if not installed and used properly, that
is, in strict accordance with the manufacturer's
instructions, may cause interference to radio and t
elevision reception. It has been type tested and fo
und to comply with the limits for a Class B computi
ng
device in accordance with the specifications in Par
t 15 of FCC Rules, which are designed to provide re
asonable protection against such interference in a
residential installation. However, there is no guar
antee that interference will not occur in a particu
lar installation. If this equipment does cause inte
rference
to radio or television reception, which can be dete
rmined by turning the equipment off and on, the use
r is encouraged to try to correct the interference
by
one or more of the following measures:
• If using an indoor antenna, replace it with a qua
lity outdoor antenna.
• Reorient the receiving antenna until interference
is reduced or eliminated.
• Move the radio or television receiver away from t
he receiver/control.
• Move the antenna leads away from any wire runs to
the receiver/control.
• Plug the receiver/control into a different outlet
so that it and the radio or television receiver ar
e on different branch circuits.
• Consult the dealer or an experienced radio/TV tec
hnician for help.
Responsible Party / Issuer of Supplier’s Declaratio
n of Conformity: Honeywell Home, 2 Corporate Center
Dr., Melville, NY 11747, Ph: 516-577-2000.
ISED CLASS B STATEMENT
This Class B digital apparatus complies with Canadi
an ICES-003.
Cet appareil numérique de la classe B est conforme
à la norme NMB-003 du Canada.
FCC / ISED STATEMENT
This device complies with Part 15 of the FCC Rules,
and ISED’s license-exempt RSSs. Operation is subje
ct to the following two conditions: (1) This
device may not cause harmful interference (2) This
device must accept any interference received, inclu
ding interference that may cause undesired
operation.


Cet appareil est conforme à la partie 15 des règles
de la FCC et exempt de licence RSS d’ISED. Son fon
ctionnement est soumis aux conditions
suivantes: (1) Cet appareil ne doit pas causer d’in
terférences nuisibles. (2) Cet appareil doit accept
er toute interférence reçue y compris les interfére
nces
causant une réception indésirable.

!

RF Exposure Warning
The antenna(s) used for this transmitter must be in
stalled to provide a separation distance of at leas
t 7.8 inches (20 cm) from all persons and
must not be co-located or operating in conjunction
with any other antenna or transmitter except in acc
ordance with FCC and ISED multi-
transmitter product procedures.
Mise en Garde
Exposition aux Frequences Radio:
La/les antenne(s) utilisée(s) pour cet émetteur do
it/doivent être installée(s) à une distance de sépa
ration
d'au moins 20 cm (7,8 pouces) de toute personne et
ne pas être située(s) ni fonctionner parallèlement
à tout autre transmetteur ou antenne,
excepté en conformité avec les procédures de produi
t multi transmetteur FCC et ISEDs.
The product should not be disposed of with other ho
usehold waste. Check for the nearest authorized col
lection centers or authorized
recyclers. The correct disposal of end-of-life equi
pment will help prevent potential negative conseque
nces for the environment and
human health.


REFER TO THE INSTALLATION AND SETUP GUIDE FOR THE C
ONTROL WITH WHICH THIS DEVICE IS USED FOR WARRANTY
INFORMATION
AND LIMITATIONS OF THE ENTIRE SYSTEM.


SUPPORT & WARRANTY

For the latest documentation and online support inf
ormation, please go to:
https://mywebtech.honeywellhome.com
For the latest warranty information, please go to:
https://www.security.honeywellhome.com/hsc/resource
s/wa/index.html
For patent information, please go to: www.resideo.c
om/patent


MyWebTech

Warranty

Patents







































This product manufactured by Resideo Technologies,
Inc. and its affiliates.
The Honeywell Home Trademark is used under license
from Honeywell International Inc


2
Corporate Center Drive
Melville, New York 11747
© 2019 Resideo Technologies, Inc

www.resideo.com

Ê800-25165AŠ
800-25165 3/19 Rev. A