Honeywell Home PROSIXMED Installation Instructions - Dated 2/19, Rev. B

PROSiXMED

1
-
Button Wireless
Sensor

Installation
and Setup Guide


This bi
-
directional wireless
sensor

is intended for
use with Honeywell Home
controls that support

PRO
SiX™ series devices.

To activate,
press and hold
the
button about 3

seconds
until the LED
flashes
.

To clear the alarm
at the control, enter a user code. To clear
memory of alarm, select Disarm and enter a user
code.


The device can be used with a belt clip,
lanyard
,
or wristband.


LED Indications

Green flashing:
lights when unit is transmi
tti ng
Red Flashing:
indicates low battery (lights
during
button
press)


ENROLL AND PROGRAM THE PROSIXMED
Follow instructions in the Controller’s programming guide.

1. Set the
controller
in Programming Mode.

2. Press and hold the button for about 3
seconds
unt
il the LED flashes
to
activate the enrollment process.

3. The LED flashes green during enrollment (up to about 20 seconds).
The
device sends its unique MAC ID (Serial Number) and Services information to
the controller.

NOTE
: Enrollment time varies depending on t
he signal strength between
the device and the controller.

4. When done, t
he LED light
s solid green for 3 seconds to confirm
enrollment.

If enrollment is not confirmed, press and hold the button
again
for
about 3
seconds to restart the enrollment process.

IM
PORTANT
: Once enrolled in a system, the PROSiXMED
cannot be used
with another controller until it is removed
from the current controller. When
removed from a system, the
sensor
will revert to factory default settings.

After Enrolling:
Verify adequate s
ign
al strength by conducting
a sensor test
(see controller’s instructions)
.


24-
HOUR ENROLLMENT DELETION AND DEFAULT

If the device is enrolled in a panel different than the intended panel, and you are unable to
delete it from the unintended panel, reset
the device to factory default setting:
Press and
hold the button for 15 seconds.
When successful the LED flashes.

The device self
-deletes from the panel it was enrolled in.

This procedure is available for 24 hours after enrollment with a panel and the dev
ice
remains powered (battery installed).



BATTERY REPLACEMENT

To replace the battery:

1.
Remove the screw
s from the back housing and use a
screwdriver to gently separate the front and back housings.

2. Use a screwdriver to carefully remove the battery.

3. Wait 10 seconds or press a button for 2 seconds to ensure
full power discharge.

4. Insert a new 3V Coin Cell battery as shown. Recommended
replacement battery:

Recommended Batteries: 3V Coin Cell

Duracell DL2450; Resideo
BL3
-0004 (CR2450)

Panasonic CR2450;
Ener
gizer CR2450

5.
Replace the f
ront housing and secure the housings with the
cover screw.


Replacing the Battery


BATTERY CAUTION
: Risk of fire, explosion and burns. Do not
recharge, disassem
ble, heat above 212°
F (100
°C) or incinerate.
Dispose of used batt
eri es properly. Keep away from
children.

NOTE
: Constant exposure to high or low temperature or high
humidity may reduce battery life.

Press and hold button 15 seconds.


SPECIFICATIONS

Battery
: 1 x 3V Coin Cell, Duracell DL2450;
Resideo
BL3
-0004 (CR2450)

Panasonic CR2450; Energizer CR2450

RF Frequency
: 2.4GHz

Operating Temperature
: 0° to 50°
C / 32° to 122° F

(Agency compliance 0° to 49° C / 32° to 120° F)

Relative Humidity
: 95%
max.
(Agency compliance –
93%
max.
),
non
-condensing

Dimensions
:
0.5” H x 1.5” L x 1.5” W / 13 mm
H x 38 mm L x 38 mm W

APPROVAL LISTINGS:

FCC / IC

cETLus Listed

Conforms
to UL
1023,

UL
985, & UL1637
Certified to
ULC ORD-
C1023

& ULC
-S545

Other Standards:

RoHS

Product must be tested at least once each year.



IMPORTANT SECURITY NO
TIC
E
Please inform the User about the security importa
nce of their wireless
sensor
, and what to do if it is lost.

They should immediately notify the Dealer/Installer of a lost or stolen
sensor
. The Dealer/Installer will then remove the
sensor

programming f
rom
the security system.



FEDERAL COMMUNICATIONS COMM
ISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or U
ser's Manual. Unauthorized cha
nge
s
or modifications could void the user's authority
to operate the equipment.

CLASS B DIGITAL DEVICE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, as defined by FCC Rules Part
15.105. The Class
B Digital Device
statement can be viewed at:

https://customer.resideo.com/en-
US/support/residential/codes
-and-
standards/FCC15105/Pages/defau
lt.aspx

FCC / IC STATEMENT

This device complies wi
th Part 15 of the FCC Rules, and Industry Canada’s license-
exempt RSSs. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device must
accept any interference received, including interferen
ce that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’Industrie Canada. Son fonctionnement
est soumis aux conditions
suivantes:
(1) Cet appareil ne doit pas causer d’interférences nu
isibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant
une réception indésirable.


RF EXPOSURE

Warning
– The antenna(s) used for this device must not be co-
located or operating in conjunction with any other antenna or transm
itter except in accordance with
FCC and ISED multi
-transmitter product procedures.

Mise en Garde

Exposition aux Fréquences
Radio :
La/les antenne(s) utilisée(s) pour cet émetteur ne pas être située(s) ni fonctionner parallèlement à tout autre transmetteur
ou
antenne, excepté en conformité avec les procédur
es de produit multi transmetteur FCC et ISED.


REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FO
R DETAILS
REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM.


Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate
Center Drive., Melville, NY 11747, Ph: 516-
577-
2000


The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized
recyclers. The correct disposal of end-
of-life equipment will help prevent potential negative consequences for the environment and human
health.

Any attempt to reverse-
engineer this device by decoding proprietary protocols, de-
compiling firmware, or any similar actions is strictly
prohibited.


SUPPOR
T & WARRANTY INFORMATION

For the latest documentation
and
support, please go to:

www.resideo.com


For the latest warranty information, please go to:

www.security.honeywellhome.com/warranty



The Honeywell Home Trademark is used under li
cense from Honeywell Inter
national Inc.

This product is manufactured by Resideo
Technologies
, Inc.
and its affiliates
.

2 Corporate Center Drive,
Suite 100
P.O. Box 9040, Melville,
NY 11747

2020
Resideo Technologies, Inc.
www.reside
o.com


Ê800
-
25226BPŠ

PROSiXMED

8
00
-
25226
B

2/19


Rev
B


Ho
me Health Care,
Household Fire &
Burglar Control
Unit Accessor
y