Honeywell Home PROSIXTEMP Installation Instructions - Dated 2/19 Rev. B

PROSiXTEMP

Wire
less Temperature Sensor

Installation
and Setup Guide

The
PROSiXTEMP
is a wireless temperature sensor intended for use with Honeywell Home
controls that support

PRO
SiX™ series devices. The sensor sends an alarm or trouble signal (depend
ing
on zone type selected; ex. Monitor
Zo
ne or 24hr Aux) when the temperature limit is exceeded. The sensor also features a front cover tamper switch.


Default Temperature Limits


Trigger Temperature

Cold

below 45
°
F (7
°
C)

Hot

above 95
°
F (35
°
C)


MOUNT T
HE PROSIXTEMP

1. To open the case, f
irmly
slide the front
and
back
housings in opposite directions and
pull them apart.

2. Mount sensor as shown, using the double sided tape and screws provided.

3. Secure the front cover with the #2
x 1/4” screw.

After enr
olling
and before mounting, verify ade
quate signal strength by conducting a sensor test
(see contr
oller’s
instructions) with the device in its intended mounting location. Adjust the device location and orientation as necessary.

A
= Tamper Switch

B
= LED


ENROLL AND SETUP


Set
the
cont
roller
in Programming Mode, when prompted:

1. Pull
the
battery tab
to activate the
PROSiXTEMP.
(Use the tamper switch
if the battery tab is removed.)

2. The LED flashes (
up to about
20 seconds*
) during enrollment.

•
The device is
automatically
enrolled in the
next
availa
ble zone number.

•
The device r
equires two zones, one for the high temperature and one for the low temperature.

•
The device sends its uniq
ue MAC ID (
Serial Number)
; the control
ler registers the device and
displays the
transmitter
data on screen
.
*NO
TE
: Enroll
ment time varies depending on
the signal strength between the device and the controller.

3. When
done,
the LED is ON for 3 seconds
to confirm
enrollment.

NOTE
: If the device is not successfully enrolled during the enrollment period, the LED turns off
and the
device powers down.
Activate
the
tamper
switch
to restart t
he enrollment process
.




IMPORTANT
: Once enrolled in a system, the PROSiXTEMP
cannot be used with another controller until it is removed
from the current controller. See the Controller’s
instruc
tions for details.

24-
HOUR ENROLLMENT DELETION AND DEFAULT

If the device is enrolled in a panel different than the intended panel, and you are unable to delete it from the unintended
panel,
reset
the device
to fact
ory default setting:

1. Open the cov
er and remo
ve the battery.

2. Hold down the tamper switch while reinserting the battery.
Rapid
LED
flashing indicates successful deletion
(LED
flashes as if in enrollment mode)
. If LED does not flash, delete
was not successful
.
3. Reattach the cover.


This pr
ocedure is ava
ilable for 24 hours after enrollment with a panel and the device remains powered (battery installed).

LED INDICATIONS


LED

Status



Rapid Flashes for

about 20 seconds, then

ON for 3 seconds

Power Up –
Enrol
lment


Slow Flashes

Power
Up
– Device e
nrolled;
Cover
Tamper activated.
To stop flashes,

clear the tamper condition
by
reattaching the cover
. It also
times out after
10 minutes.


ON

(while in Programming Mode)

Sensor LED toggles on and off when the s
ensor is selected. See Sensor

Location Fea
ture.

BATTERY REPLACEMENT

•
Push the bottom latch of the mounting bracket back to disengage
it. Then
slide the back housing, up and out to remove
it from the
mounting
bracket
.

•
Slide the front and back housings in
opposite directions
and pul
l the housings
apart
.
•
Re
move
the battery
,
wait
10 seconds
,
then insert a new battery
. Recommended batteries:
Resideo 466

Dur
acell DL123A

Huiderui CR123A

Panasonic CR
123A

•
Place the front and back housings together and slide th
em together as shown.

BATT
ERY
CAUTION
: Ri
sk of fire,
explosion and burns. Do not recharge, disassemble, heat above 212
°F (100°
C)
or incinerate. Dispose of used
batteries proper
ly. Keep away from
children.

NOTE
: Constant exposure to high or low temperature
or high humidity may reduce
battery life
.

SPECIFICATIONS:

Battery:
1 x 3V Lithium, Panasonic CR123A, Resideo 466

Duracell DL123A or Huiderui CR123A

Tamper:
Cover

RF Frequency
:
2.4GHz

Operating Temperature
: 32°
– 122° F / 0°
– 50° C

(Agency Compliance 32°
– 120° F / 0°
– 49° C)

Relative
Humidity
:
95% max. (Agency Compliance -
93% max.),
non-
condensing

Dimensions:
1” H x 3.13” L x 1.61” W / 25.5 mm H x 79.5 mm L x 41 mm W


APPROVAL LISTINGS:

FCC / IC

cETLus Listed

Conforms to ANSI/
UL
873
and
ANSI/
UL
2017

Cert
ified to CAN/C
SA STD C2
2.2
#205

Other Standards:

RoHS


Product must be tested at

least once each year



FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS

The user shall not make any changes or modifications to th
e equipment unless authoriz
ed by the Installation
Instruction
s or User's Manual. Unauthorized changes or
modifications could void the user's authority to operate the equipment.



CLASS B DIGITAL DEVICE STATEMENT

This equipment has been tested to FCC requir
ements and has been foun
d a
cceptable for use. The
FCC require
s the following statement for your information: This equipment
generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufactur
er's instructions, may c
aus
e interference
to
radio
and televi
sion reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with
the specifications in Part 15 of
FCC Rules, which are designed to provide reasonable protecti
on
against such interferen
ce in a res
idential installation. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by
turning the equip
ment off
and on,
the user is encouraged to try to correct the interference by one or more of the following measures:

•
If using an indoor antenna, replace it with a quality outdoor antenna
.
•
Reorient the receiving a
ntenna until interferenc
e is reduced or el
iminated.

•
Move the
radio or television receiver away from the receiver/control.

•
Move the antenna leads away from any wire runs to the receiver/control.

•
Plug the receiver/control into a different outlet so that it a
nd the radio or televisi
on
receiver are on
different branch c
ircuits.

•
Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA CLASS B STATEMENT

This Class B digital apparatus complies with Canadian ICES
-003.

Cet appareil numérique de la classe B est confor
me à la norme N
MB
-003 d
u Canada.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and
Industry Canada’s license-
exempt
RSS
s. Operation is subject to the following two conditions: (1) This device may not
caus
e harmful interference,
and
(2) This devic
e must accept any i
nterference received, including interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC
et exempt de licence RSS d’Industrie Canada. Son fon
ctionnement est soumis a
ux
conditions suiv
antes: (
1) Cet
appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une r
éception indésirable.

RF EXPOSURE

Warning

– The
antenna(s) used for thi
s device must be i
nstalled to provide a separation distance of at lea
st 7.8 inches (20 cm) f
rom all
per
sons and must not be co-
located or operating in conjunction with any other antenna or transmitter except in accordance with FCC
and ISED multi
-transmitte
r product procedur
es.

Mise en garde

Exposition aux fréquences

radio :

La/les antenne(s) util
isée(s) pou
r cet émetteur doit/doivent être installée(s) à une distance de
séparation d'au moins 20
cm (7,8
pouces) de toute personne et ne
pas être située(s) ni fonctionner parallèl
ement à tout autre
transmetteur ou antenne, excepté
en conformité avec les
procédures
de produit multi transmetteur FCC et ISED.

REFER
TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USE
D, FOR
DETAILS REGARDING
LIMITATIONS OF TH
E ENTIRE ALARM SYSTEM.


Responsible Party / Issuer of Supplier’s Declaration of
Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Drive.,
Melville, NY 11747, Ph: 516-
577-
2000


The product should not be disposed of with
other household waste. Check for the nearest authorized collection centers or authorized recyclers. The
correct disposal of end-
of-life equipment will help prevent potential negative consequences for the environment and human health.

Any
attempt to revers
e-engineer this device by decoding proprietary protocols, de-
compiling firmware,
or any similar actions is strictly prohibited.


SUPPORT & WARRANTY INFORMATION

For the latest documentation
and
support, please go to
:
www.resideo.com


For the latest warranty information, please go to:

www.security.honeywellhome.com/warranty



The Honeywell Home Trademark is used under license from Honeywel
l International Inc.

This product is manufactured by Resideo
Technologies, Inc.
and its affiliates
.

2 Corporate Center Drive, Suite 100
P.O. B
ox 9040, Melville, NY 1
1747

2020
Resideo Technologies, Inc.
www.re
sideo.com



Ê800
-
25252
BDŠ

PRO
SiXTEMP
800
-
25252
B

2
/19

Rev
B