Honeywell LGB500 Quick Install Guide

This wireless glassbreak detector is intended for
use with Honeywell controls that support SiX™
series devices.
FC: This wireless glassbreak detector is intended
for use with Honeywell controls that support SiX™
series devices.
SP: This wireless glassbreak detector is intended
for use with Honeywell controls that support SiX™
series devices.
PA: This wireless glassbreak detector is intended
for use with Honeywell controls that support SiX™
series devices.

GlassBreak
NOTE: Once enrolled, the
device cannot be used with
another system until it is
removed from the current
controller. See the
controller’s instructions.
NOTE: Once enrolled, the
sensor cannot be used with
another system until it is
removed from the current
controller. See the
controller’s instructions..
NOTE: Once enrolled, the
sensor cannot be used with
another system until it is
removed from the current
controller. See the
controller’s instructions..
NOTE: Once enrolled in a
system, the RF6GB cannot
be used with another
control panel until it is
removed from the current
control panel. See the
Control’s

Enroll / Enroll / Enroll / Enroll

Mounting Locations and Options
Mounting Locations and Options
Mounting Locations and Options
Mounting Locations and Options


LEDS / LEDS / LEDS /S


NOTE: The LEDs are not visible during Normal Mode.
NOTE: The LEDs are not visible during Normal Mode.
NOTE: The LEDs are not visible during Normal Mode.
NOTE: The LEDs are not visible during Normal Mode.

G1 R G2 Status


10 minute Test Mode
1




Event detected during Test Mode




Alarm detected during Test Mode




1

Low Battery detected during Test Mode




Power Up / Tamper switch pressed / FG-701 Activated
before enrollment




Tamper Detected

1
NOTE: Before using Test Mode, the device must first be enrolled in the controller.
NOTE: To enter Test Mode, the device must first be enrolled in the controller.
NOTE: To enter Test Mode, the device must first be enrolled in the controller.
NOTE: To enter Test Mode, the device must first be enrolled in the controller.

 2014 Honeywell International Inc. Honeywell and is a registered trademark of Honeywell International Inc.
All other trademarks are the properties of their respective owners. All rights reserved


2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
www.honeywell.com/security
Ê800-15962YŠ
800-15962 04/15 Rev A BETA

NOTE: After enrolling and before mounting
permanently, conduct Go/No Go tests (see
controller’s instructions) to verify adequate
signal strength. Adjust the device location and
orientation as necessary.
FC: NOTE: After enrolling and before
mounting permanently, conduct Go/No Go
tests (see controller’s instructions) to verify
adequate signal strength. Adjust the device
location and orientation as necessary.
SP: NOTE: After enrolling and before
mounting permanently, conduct Go/No Go
tests (see controller’s instructions) to verify
adequate signal strength. Adjust the device
location and orientation as necessary.
PA: NOTE: After enrolling and before
mounting permanently, conduct Go/No Go
tests (see controller’s instructions) to verify
adequate signal strength. Adjust the device
location and orientation as necessary.

Mount / Mount
Consult the Controller’s instructions to
program the GlassBreak Services: Tamper
Switches, Sensitivity Setting and
Temperature Sensing.
FC: Consult the Controller’s instructions to
program the GlassBreak Services: Tamper
Switches, Sensitivity Setting and
Temperature Sensing.
SP: Consult the Controller’s instructions to
program the GlassBreak Services: Tamper
Switches, Sensitivity Setting and
Temperature Sensing.
PA: Consult the Controller’s instructions to
program the GlassBreak Services: Tamper
Switches, Sensitivity Setting and
Temperature Sensing.

Sensitivity
Setting
Approximate
Range
High * 4.6-7.6m / 15-25 ft.
Medium 3-4.6m / 10-15 ft.
Low 1.5-3m / 5-10 ft.
Lowest 0-1.5m / 0-5 ft.
* Factory default / Valeurs par défaut du
fabricant / Defecto de fábrica / Padrão
de fábrica
Program / Program /
Program / Program
FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation
Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the
equipment.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son
fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2)
Cet appareil doit accepter toute interférence reçue y compris les interférences causant une reception indésirable.
RF Exposure
Warning – The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8
inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with FCC multi-transmitter product procedures.
Mise en Garde
Exposition aux Frequences Radio: L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de
séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.

Replace Battery / Replace Battery /
Replace Battery / Replace Battery

BATTERY CAUTION: Risk of fire, explosion and
burns. Do not recharge, disassemble, heat above
212° F (100° C) or incinerate. Dispose of used
batteries promptly. Keep away from children.
FC: BATTERY CAUTION: Risk of fire, explosion
and burns. Do not recharge, disassemble, heat
above 212° F (100° C) or incinerate. Dispose of
used batteries promptly. Keep away from
children.
SP: BATTERY CAUTION: Risk of fire, explosion
and burns. Do not recharge, disassemble, heat
above 212° F (100° C) or incinerate. Dispose of
used batteries promptly. Keep away from
children.
PA: BATTERY CAUTION: Risk of fire, explosion
and burns. Do not recharge, disassemble, heat
above 212° F (100° C) or incinerate. Dispose of
used batteries promptly. Keep away from
children.

Specifications:
Range: 0’- 25’/ 0 – 7.6m; Selectable
RF Frequency: 2.4GHz
Battery: 1 x 3V, Lithium; Panasonic
CR123A, Duracell DL 123, Duracell DL
123A, Honeywell 466
Tamper: Cover and Wall
Operating Temperature: 32° – 122° F /
0° – 50° C
Relative Humidity: 5 – 95%, non-
condensing
Dimensions: 3.78” Diameter x 1.14” Thick
/ 96 mm Diameter x 29mm Thick

Approval Listings:
FCC / IC
ETL Listed to UL639
cETL Listed to ULC S306-03
RoHS

Protected Glass Types Chart [PRELIMINARY – TBD AFTER AGENCY TESTING]
NOTE: The RF6GB is NOT recommended for protection of glass areas smaller than 27.6 cm x 27.6
cm (10-7/8 inches x 10-7/8 inches).
Glass Type*
Nominal Thickness
Minimum Maximum
Plate 2mm (3/32 in.) 10mm (3/8 in.)
Tempered 3mm (1/8 in.) 10mm (3/8 in.)
Laminated
1
3mm (1/8 in.) 14mm (9/16 in.)
Wired 6mm (1/4 in.) 6mm (1/4 in.)
Coated
2
3mm (1/8 in.) 6mm (1/4 in.)
Sealed Insulating
1

3mm (1/8 in.) [13mm
(1/2 in.) overall]
6mm (1/4 in.) [19mm
(3/4 in.) overall]

* Minimum size for all types is 28cm (11 in.) square; glass must be framed in the wall or mounted in a barrier at
least 0.9m (36 in.) wide.
1
Protected only if both plates in the unit are broken
2
Coated glass with security films up to 0.35mm (14 mils) thick (including films for solar protection) may be used.
Evaluated with the these products: 3M
®
SCOTCHSHIELD
®
SH14CLARL – 0.35mm (14 mils), 4 ply film; Film
Technologies International, Inc.’s GLASS-GARD GGLL 1200 has been evaluated with this product by
Underwriters Laboratories, Inc.

Product must be tested at least once each year / Le fonctionnement du produit doit être vérifié au moins une fois par année / El
producto debe ser probado al menos una vez al año / O produto deve ser testado pelo menos uma vez por ano
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE
ALARM SYSTEM.
Support / Support / Support / Support
https://mywebtech.honeywell.com/
U.S. warranty / U.S. warranty / U.S. garantie / U.S. garantia
www.honeywell.com/security/hsc/resources/wa


MyWebTech

Warranty