Honeywell Tuxedo Touch WIFI Quick Install Guide

Tuxedo Touch WIFI Home Automation System Ê800-10300QG.Š
Quick Installation Guide
KEYPAD INITIALIZATION
When initially powered, the boot sequence and the "Set ECP Address" is displayed. If using one keypad, leave the address set to 1 and press Apply. If using more than one, power-up each keypad one at a time, and set each keypad address to one of the addresses enabled in the panel. Language Selection- If applicable, after initial ECP selection is set, the “Languages” menu is displayed. Select a language. Installer Note: The Tuxedo Touch Screen is factory calibrated. Ignore the “CALIBRATE” button that appears after ECP setup. Note: To set the “Screen Blackout” option, see section below.

800-10300QG

6/12

Rev. A

Full Installation Guide available online at: http://www.security.honeywell.com/hsc/resources/MyWebTech/.

IP SETUP – Set the IP Address

MULTI-MEDIA – Picture, Video, Camera Setup
Picture Setup: Press Multi-Media ! Picture . 1. Insert a media card (SD/SDHC) with up to 1000 stored (.bmp, .png or .jpg) photos. 2. Press the viewing transition arrow; select Standard, Horizontal, Vertical, and Fade Out. 3. Press the Slide Delay arrow to select a time interval for viewing pictures. - Use the icons to: Play Image ! view Previous Image

ECP ADDRESS – Change the ECP Address
If the screen is displaying “ECP Error”, the ECP address in the keypad is not valid for the panel that it is connected to. In this case, to change the ECP Address, enter the default code of “4140” to advance to the next screen. Note: Default code “4140” is the Tuxedo Touch default installer code before connecting to a control panel. Once connected to a control panel, use that panel’s installer code. 1. Press Setup !System Setup ! CS Setup. 2. Enter an Authorized Code, if required. 3. Press ECP Address; use the Up/Down arrows to select a new address. The available ECP addresses are: 1-2, 5-6….. for residential controls 1-2, 3-30... for older commercial controls under Rev. 10; supports 3 AUIs. *See Important Note below. 1-30 ……. for commercial Turbo controls; supports 6 AUIs. *IMPORTANT NOTE: If multiple keypads are being used, they must be set to addresses 1, 2, and X (where X equals any address from 3 through 30). Only one AUI type (touch screen) device may be assigned to an address from 3 through 30 on commercial control panels.

The Tuxedo Touch Keypads IP Address is used on a standard web browser to control user functions such as Security, Z-Wave operation, and camera viewing. 1. Press Setup ! IP Setup. 2. Select a type of network connection: LAN ON or WIFI ON. For LAN ON (default selection): - Connect an Ethernet cable between the router and the Keypad; the IP address and default gateway address of the router is displayed. - If the IP address is not displayed, change the “Internet Connection Type” to Static and manually enter the necessary IP information from your router onto the keypad. - Press Save. For WIFI ON: - Press WIFI ON; a local WIFI list is displayed. Select the desired WIFI router and enter the Passphrase/Shared Key (if applicable). - If the WIFI router is not broadcasted, scroll to the bottom of the list and select Add Network; enter your SSID and if applicable, the Security Mode/Passphrase/Shared Key. - Press Save. Notes: • Pressing “Save” after changing the port number resets the keypad. • To view connectivity, press the System Information icon (see section below). • If left inactive, Web connections disconnect after 10 minutes. 3. Press Account Setup to create a browser log-on page for each user (for higher security) when viewing from a web enabled device or PC on a different sub-net. Enter the required information for each field; press Save.

! go to Next Image ! or Add Image . - Use the slide bar to select a wallpaper file from the list and . press Set Wallpaper (* While viewing photos in Full View, press anywhere on the screen to exit.) ! Video . Video Setup: Press Multi-Media Insert a media (SD/SDHC) card (with stored video files). Maximum video resolution should not exceed 400 x 240. - Highlight a video file from the list and press Play to start the selected video file. to continually replay selected video. - Press Repeat - Deselect the Repeat icon to play the list of video files starting with the first video and ending with the last. ! view a Full View . - Use the icons to: Pause (* While viewing videos in Full View, press anywhere on the screen to exit.) Note: See the Video Converter document to convert videos for proper playback on the Touch Keypad (provided in the carton). Camera Setup: See the full Installation Guide for further information. • If using existing (mounted) cameras; go to Step 4. • If this is a first time setup, scan/configure the cameras prior to mounting, and then do the following: 1. Connect an Ethernet cable to the back of the camera (LAN); connect the opposite end to the Ethernet port on the router. 2. Apply power to the camera; wait for initial power-up. 3. Press Multi-Media ! Camera ! Camera Setup .

AUTOMATION – Enroll / Add Z-Wave devices

Add a Z-Wave Light, Switch, or Outlet Module: (if using two keypads, see Secondary Keypad [Controller] below). 1. Install device according to the manufacturer’s directions. 2. Press Automation ! Z-Wave Setup !

DATE AND TIME –

Set the current time and date

1. Press Setup ! System Setup! Time/Date Setup. 2. Enter an “Authorized Code”. a) If Get Time is pressed, the keypad downloads the time/date from the control panel and exits the ‘Set Time’ screen. (The Get Time icon appears with residential panels and may not appear with all commercial panels.) b) Or, set the time/date from the Set Time/Date screen. 3. Press Apply and answer Yes to the next prompt.

NIGHT SETUP – Change arming modes
The NIGHT function can be set to arm the system in one of five arming modes. To change the arming mode; 1. Press Setup !System Setup !Advanced Setup. 2. Enter an Authorized Code. 3. Press Night Setup; select desired mode: Away - Stay - Instant (default) - Night (Residential Only) – Maximum.

DISPLAY & AUDIO SETUP- Adjust display
1. Press Setup; slide the Brightness / Volume bar up or down to change settings. Press Yes to save. 2. Press Setup ! Disp & Audio Setup; enter an Authorized Code. - To adjust the screen timeouts, select a time interval from the drop-down list for each option (Backlight Off After, To Homepage After, and Auto Slideshow After.) - Select Chime, Voice or Voice Chime operating mode. - To clean the keypad screen, press the Clean Screen icon; press Continue, or press Cancel to exit. - Press the Save icon.

. Z-Wave Enroll / Add 3. Press the Function Key on the device; follow the keypad’s on-screen messages until “Device added successfully”. Add a Door Lock: 1. Assemble the Z-Wave door lock according to the manufacturer’s instructions. Be sure the door lock orientation/handedness is correct. 2. Refer to the Door Lock’s Instruction Guide and connect necessary cables, then install batteries. 3. Enroll the door lock within 5 feet of the keypad; refer to the Door Lock’s Instruction Guide for procedure. Note: Program a 4-digit user code in the control panel prior to programming that user code into the door lock. 4. Press Automation ! Z-Wave Setup ! Z-Wave Enroll / Add. 5. Program the selected user code from the panel. Add a Honeywell Thermostat: 1. Install thermostat according to the manufactures directions. 2. Press Automation ! Z-Wave Setup ! Z-Wave Enroll / Add; the keypad displays a series of messages. If not using a Honeywell thermostat, enrollment procedure may vary. Refer to the Thermostat instructions. 3. On the Honeywell thermostat select Thermostat; set the “Time/Date” and follow the instructions in the thermostat Installation Guide for enrollment. 4. To complete, press Done. 5. Press Exit to return to normal operation. 6. To verify activation: on the Tuxedo Touch Keypad, press ; wait 30 seconds. Press Refresh ; the new Back device is displayed. See Installation Guide to Delete/Edit/Abort Z-Wave devices.

4. Press Discover to locate the camera. The screen displays “Discovering Cameras Please Wait…” Note: For best performance set video resolution to 320 x 240, 8 frames per sec., Normal quality. 5. Press the Add icon if the camera information is not discovered automatically, to enter information manually. 6. To edit camera information, highlight the camera name and icon. Enter required information and then press the Edit press the Save icon. a) To retrieve camera settings and connect to the camera, press the Connect icon.

to reset the camera for remote b) Press Total Connect viewing and activate a Total Connect account. c) Press Reset to reset the camera to factory default. Select Yes or No. 7. When all cameras have been added, press Camera WIFI and enter the wireless information from the router. 8. Press Apply to All to set cameras to wireless operation. 9. Press Settings to enter advanced settings for Video, Network, Wireless and Other settings. 10. Remove Ethernet cable from wireless cameras to view wirelessly via the Keypad. If the camera does not have wireless capability, leave the camera connected. Use the icons to: Delete/Delete ALL ! Refresh ! Pan/Tilt Notes: ! Auto Pan ! Back ! Play ! Stop ! Full View

SCREEN BLACKOUT (EN50131 DISPLAY)
The Screen Blackout (EN50131 Display) compliance feature is a European Standard designed to prevent unauthorized users from viewing the status of the Security System by blanking the screen after 30 seconds, to enable: 1. Press Setup ! System Setup !CS Setup. 2. Enter an Authorized Code, if required. 3. Press Options and select "EN50131 Display" to turn the option on or off; press Apply.

SCENE SETUP – Define (up to 10) Scenes

The Scene feature is used to control a single device, or multiple devices based on pre-set “Conditions,” “Triggers,” and “Actions.” When a trigger/condition occurs, the defined action is executed. ! Add . 1. Press Automation ! Scene Setup 2. Press Scene Name; enter a “name” and press OK. 3. Add the “Condition,” “Trigger,” and “Action” that you want to occur for this Scene (see below). 4. After each selection press Save !! Note: Determine if you need a Condition. The Condition is a ‘condition’ set to occur prior to a trigger event. See example below. Example: Turn the lights on when the system disarms, but only at night. (Condition) … “only at Night” ….Set the TIME Condition (enter the Start Time and Duration). (Trigger) … …when the “system Disarms” …Set the Trigger to SECURITY: System Disarm (Action) … …Turn the “lights ON” … Set the Action to LIGHT: ON. Scene Rules • Triggers and Conditions include: Time setting, Security mode, Thermostat setting, and Door status. • Actions include: Security, Lights On/Off/On For Time, Thermostat, and Doors. • Each Trigger event can have up to 3 Actions. • A Trigger event and Condition cannot be the same (i.e., if setting a Trigger event for SECURITY, you cannot set a SECURITY Condition). • On commercial panels the programming option for “Global Keypad” must be set to “0” for some Scenes to work properly. See the full Installation Guide.

! Quad View .

USER SETUP: Add a User
1. Press Setup ! System Setup ! USER SETUP ! ADD USER. 2. Enter an Authorized Code; select each field and enter the appropriate information. 3. Press Save. For available user numbers, see control panel instructions.

1. QuickTime® media player must be installed on your PC. 2. Camera viewing is compatible with IE8 (and above) and Safari 5.0 (and above); and not compatible w/Opera web browsers. 3. Do not use ports 6665-6669 for camera HTTP configuration.

SECONDARY KEYPAD (Controller)

SCREEN SECURITY- View authority levels

After all Z-Wave devices have been enrolled into the Primary Keypad (Controller #1), the device information can be downloaded to a Second Keypad (Controller #2). Keep the controllers within 10 feet of each other. 1. On Controller #1: Press Automation ! Z-Wave Setup 2. On Controller #2: Press Z-Wave Primary side of screen.) .

See the full Installation Guide for user Authority Levels. 1. Press Setup ! System Setup ! CS Setup. 2. Enter an Authorized Code and press Screen Security. - To make changes, select the line to change and the level of user to have access, and then press Apply.

. (Lower right

CODE AUTHORITY

– View users / authority levels

1. Press Setup ! System Setup ! CS Setup. 2. Press Code Authority. 3. Enter the 4-digit Code for the user you want to obtain authority level information about.

- Select Yes to change this keypad to Secondary 3. On the Primary Controller (#1): Press Add; 4. On the Secondary Controller (#2): Press Add. See the full Installation Guide for further information.

.

PANEL CONFIGURATION–View system details
1. Press Setup ! System Setup ! CS Setup. 2. Enter an Authorized Code and press Panel Config. - Delete clears the keypad and reloads the panel configuration into the keypad.

OUTPUT SETUP–Display (up to 18) outputs
1. Press Setup !System Setup !Advanced Setup. 2. Enter an Authorized Code. 3. Press Output Setup. 4. Select the outputs to display on the Output screen by pressing Enable or Disable and then press Apply.

SYSTEM INFORMATION / UPGRADES
To view the current software version installed, and verify connectivity, press Setup ! System Information .

PRODUCT / TRAINING VIDEOS
Press Product Introduction and Training Video icon . • Customizable Automation Scene Training Video • Programming of Z-Wave Devices Training Video • SD Card Video Playback Training Video • Local System Control (Tablet/Smartphone) Training Video • IP Camera Setup Training Video.

WEATHER FORECAST – Set a location
1. Press the Weather feature on the “Home” screen. 2. Select USA/Canada, Zip Code/Postal Code and enter the information on the data entry keyboard; Press Back.

Software upgrades may be available. Log in to MyWebTech and enter model name in the “Search by” “My Product” field. Press Go; Click on “Tuxedo Touch software update SBS”.

Panel Faults – If Panel Fault icons are displayed on the Security screen, contact your alarm company. See the full Installation Guide.
AC Loss Bell Failure Expander Failure Low Battery LRR Supervision Failure Max Attempts Exceeded Pager Failure Telco-1 Cut Telco-2 Cut Wireless Failure Panic

TUXEDO TOUCH WIFI
3
CONNECT WIRING

1
WALL SURFACE CONTROL PANEL

REMOVE CASE BACK

2

MOUNT TO WALL

This Keypad is for indoor use only and should be mounted at a comfortable viewing level. Avoid mounting in areas of high condensation such as bathrooms or in locations where bright light or sunlight shines directly on the screen. The TouchCenter can be mounted with or without the mounting plate. Use the center securing screw for European installations.

DETACH THE MOUNTING PLATE BY SLIDING DOWNWARD

MOUNTING OPTION 1

CONTROL TERMINAL STRIP AUX AUX DATA DATA IN OUT

SEE DETAIL A LOCATE THE MOUNTING PLATE WITH THE SURFACE AND CABLE/WIRE ACCESS

USE MOUNTING PLATE TO MARK LOCATION OF HOLES ON SURFACE. CHECK FOR LEVEL

YELLOW (DATA FROM CONTROL)

MOUNTING PLATE WALL SURFACE MOUNTING PLATE

Y

RED (+12VDC) BLACK (GND)

G
RJ45

TURNED 90

GREEN (DATA TO CONTROL)

SECURE THE MOUNTING PLATE TO THE SURFACE USING THE FOUR (4) SCREWS PROVIDED
628 0S ER IES CA SE BA
43/4"

IP CONNECTION

MOUNTING OPTION 2
CK MO UN TIN GT EM PL AT E

INSTALL FOUR (4) MOUNTING SCREWS LEAVE 1/8” ABOVE SURFACE. MOUNT KEYPAD BY SLIDING PLATE DOWNWARD ONTO SCREW HEADS.

DETAIL A SUPPLEMENTARY POWER CONNECTIONS
POWER FROM SUPPLEMENTARY POWER SUPPLY IF USED
CONTROL TERMINAL STRIP

COMPATIBILITY
CU T-O UT LO CA TIO N S 3/1 4 P6" DIA LA . H CE OL S E ILL DR

WITHOUT MOUNTING PLATE USE TEMPLATE TO MARK LOCATION OF SCREWS AND CUT-OUT FOR THE KEYPAD ON SURFACE. CHECK FOR LEVEL
Ê8
0883 1 Re v.A

INSERT SD CARD
800-

00-0
OL E
3 - 9/16"
5/11

DR

The table below identifies the alarm systems that the keypad can interface with, the maximum number of keypads that can be used with each system, and the minimum alarm panel software revision level for compatibility.
083 1uŠ
DIA .H 6" ILL 3/1

TEMPLATE

CASE FRONT

SUPPLEMENTARY +12 VDC POWER SUPPLY P/N AD12612

AUX AUX DATA DATA IN OUT

Alarm System

Maximum Number of Keypads

Minimum Software Revision Level

BLACK CASE BACK

MOUNTING PLATE (NOT USED DISCARD)

SPECIFICATIONS:
Mechanical Specifications: Width: 8.23 inches (209.04mm) Height: 5.59 inches (141.99mm) Depth:1.13 inches (28.70mm) Electrical Specifications: Backlight OFF, Sound OFF Backlight ON, Sound OFF Backlight ON, Sound ON Operating Environment: Humidity Operating Temp. Ship/Storage/Temp. 93% RH, non- condensing 14˚ F to 131˚ F / -10˚ C to 55˚ C (UL tested 32˚-120˚F / 0 to 49˚C) -40˚ F to 158˚ F / -40˚C to 70˚C 12V, 140mA 12V, 205mA 12V, 350mA

SD/SDHC CARD Slot ARMED (RED) LED ON – System is armed. OFF – System is not armed.

DETACH CASE FRONT BY REMOVING SCREWS (2) AND LIFT UP INSTALL CENTER SECURING SCREW

BLACK RED GREEN YELLOW

WIRING

READY (GREEN) LED ON – System is disarmed and ready to arm. OFF – System is armed or disarmed but not ready. If disarmed, faults or troubles are present.

REPLACE CASE FRONT

Connect the Tuxedo Touch in parallel with keypads and other peripheral devices using the keypad data (ECP) bus. If more than one keypad is wired to one run, then the maximum lengths must be divided by the number of keypads on the run. (e.g., the maximum length is 75 feet if two keypads are wired on a #22 gauge run).
Wire Gauge: #22 gauge #20 gauge #18 gauge #16 gauge Length 150 feet 240 feet 350 feet 550 feet

VISTA-15P/FA148CP VISTA-20P/FA168CPS VISTA-20P/FA168CPS VISTA-21P VISTA-128BP/SIA/FA1660C VISTA-128FBP VISTA-128FBP-9/FA1670C-9 VISTA-250FBP-9/FA1700C VISTA-250BP VISTA-250FBP/FA1700C VISTA-250FBP/FA1700C VISTA-128BPE/SIA/FA1660CE VISTA-250BPE VISTA-128BPEN VISTA-128BPLT VISTA-128FBPN VISTA-128BPT/SIA/FA1660CT VISTA-250BPT

2 2 4 4 3 3 3 3 3 1 3 3 3 3 3 3 6 6

3.0 3.0 5.0 1.0 2.4 1.6 4.1 4.1 2.4 1.5 2.0 4.3 4.3 7.0 6.0 5.1 10.1 10.1

MESSAGE (YELLOW) LED FLASHING – The system contains new message(s) for the User. OFF – No new messages. RESET BUTTON Press to reset keypad

(OPTIONAL) SECURING THE CASE BACK REQUIRED FOR EUROPEAN INSTALLATION

WIFI-mounting_wiring-001-V0