Honeywell Vista-128BPT/250BPT- User Guide Dated 06/10 Rev E
Related Products
Related Categories
Document Transcript
VISTA
-128BPT/
VISTA
-250BPT/
VISTA
-128BPTSIA
C
C
o
o
m
m
m
m
e
e
r
r
c
c
i
i
a
a
l
l
B
B
u
u
r
r
g
g
l
l
a
a
r
r
y
y
P
P
a
a
r
r
t
t
i
i
t
t
i
i
o
o
n
n
e
e
d
d
S
S
e
e
c
c
u
u
r
r
i
i
t
t
y
y
S
S
y
y
s
s
t
t
e
e
m
m
W
W
i
i
t
t
h
h
S
S
c
c
h
h
e
e
d
d
u
u
l
l
i
i
n
n
g
g
U
U
s
s
e
e
r
r
G
G
u
u
i
i
d
d
e
e
800-
06905 6/10 Rev. E
IMPORTANT!
RECOMMENDATIONS FOR PROPER INTRUSION PROTECTION
For proper intrusion coverage, sensors should be located at every possible point of entry to a home or
commercial premises. This would include any skylights
that may be present, and the upper windows in a
multi
-level building.
In addition, we recommend that radio backup be used in a security system so that alarm signals can still
be sent to the alarm monitoring station in the event that the telephone lines ar
e out of order (alarm
signals are normally sent over the phone lines, if connected to an alarm monitoring station).
EARLY WARNING FIRE DETECTION
Early warning fire detection
is important in a home. Smoke and heat detectors have played a key role in
reducing fire deaths in the United States. With regard to the number and placement of smoke/heat
detectors, we subscribe to the recommendations contained in the National Fire Protection Association's
National Fire Alarm Code (NFPA 72).
SYSTEM COMPATIBILITY NOTICE
Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell
for use with your security system. Your Honeywell security system is
not designed for use with any device
that may be attached to your security system's keypad or other communicating bus if Honeywell has not
approved such device for use with your security system. Use of any such unauthorized device may cause
damage or comp
romise the performance of your security system and affect the validity of your Honeywell
limited warranty. When you purchase devices that have been manufactured or approved by Honeywell,
you acquire the assurance that these devices have been thoroughly tes
ted to ensure optimum
performance when used with your Honeywell security system.
About This Manual
This manual is a step
-by
-step guide that will acquaint you with the system's features and benefits. It
defines the components and their functions, describes
their operation, and provides clear step
-by
-step
instructions for normal and emergency procedures. Keep this manual in a convenient place so that you
can refer to it as necessary.
i
Table of Contents
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
1.
SYSTEM OVERVIEW
General
.............................................................................
1
A Partitioned System
.................................................
2
Zones
.................................................................................
2
Fire Protection
..............................................................
2
Carbon Monoxide Protection
................................
2
Alarms
...............................................................................
2
False Alarm Prevention
Features
........................
3
Cross Zoning and Swinger Suppression
..........
3
Keypad Lockout
...........................................................
3
Error Message Displayed
........................................
3
Burglary Protection
....................................................
4
Memory of Alarm
.........................................................
4
Speed Key (Mac
ros)
...................................................
4
Using Schedules
..........................................................
4
Device Timers
................................................................
5
Accessing another Partition (GOTO
Command)
......................................................................
5
Master Keypad Operation
.......................................
5
Self
-Help Feature
........................................................
5
Viewing Abbr
eviated Messages
...........................
5
2. ABOUT THE KEYPADS
General
.............................................................................
6
The Alpha Keypad
........................................................
6
3. FUNCTIONS
OF THE KEYPADS
4. ENTRY/EXIT DELAYS
General Information
................................................
10
Exit
Delay
......................................................................
10
Entry Delay
...................................................................
10
Defaults and Requirements
................................
10
Exit Delay Reset
.........................................................
10
Burglar Alarm Communication Delay
............
10
5. SECURITY CODES AND A
UTHORITY
LEVELS
General Information
...............................................
11
Duress Code
...............................................................
11
Quick Arming
.............................................................
11
Installer Code L
ockout
..........................................
11
Authority Levels
........................................................
12
Authority Levels and Changes
..........................
13
To Exit User Edit Mode
.........................................
13
To Add a User
.............................................................
14
To Change a User's Code
.....................................
16
To D
elete a User
.......................................................
17
6. ACCESSING OTHER PART
ITIONS
To Access another Partition (GOTO)
..............
18
7. GLOBAL ARMING
Global Arming Notes
..............................................
19
Global Arm
...................................................................
19
Global Disarm
............................................................
19
8. MASTER
KEYPAD
Operation
.....................................................................
20
9. COMMON LOBBY
Operation
.....................................................................
22
Affecting the Lobby (Disarming)
.....................
22
Arming the Lobby
....................................................
22
How User Codes Affect the Common
Lobby
.............................................................................
23
Codes with “Global” Arming
................................
23
Codes with
“Non
-Global” Arming
.....................
23
Other Methods of Arming/Disarming
...........
23
ii
10.
CHECKING FOR OPEN ZO
NES
Using the
∗
READY Key
..............................
24
Showing Faulted Zones
.....................................
24
11.
DISPLAYING ALL ZONE
DESCRIPTORS
Using the A
∗
AREADY Key
............................
25
Displaying Descriptors
......................................
25
12.
BYPASSING PROTECTION
ZONES
Using the
6
BYPASS Key
............................
26
To Bypass
.................................................................
26
Quick Bypass
..........................................................
27
Quick Bypassing
...................................................
27
Viewing Bypassed Zones
..................................
27
Group Bypass
.........................................................
28
Bypassing Groups
................................................
28
Zones Remaining Bypassed After
Disarming
.................................................................
29
13.
ARMING STAY WITH ENT
RY DELAY
Using the
3
STAY key
...................................
30
Operation
.................................................................
30
Stay Modes
..............................................................
30
Arming STAY
...........................................................
31
Auto
-STAY Arming
...............................................
31
14.
ARMING
STAY WITH NO ENTRY D
ELAY
Using the
7
INSTANT Key
..........................
32
Operation
.................................................................
32
Instant Modes
........................................................
32
Arming INSTANT
...................................................
32
15.
ARMING ALL PROTECTIO
N (WITH ENTRY
DELAY)
Using the
2
AWAY Key
.................................
33
Operation
.................................................................
33
Arming Away
...........................................................
33
16.
ARMING ALL PROTECTIO
N (NO ENTRY
DELAY)
Using the
4
MAXIMUM Key
......................
34
Operation
.................................................................
34
Arming MAXIMUM
..............................................
34
17.
QUICK EXIT
Using the
#
+
9
Keys
..............................
35
Arming with Quick Exit
......................................
35
18.
DISARMING AND SILENC
ING ALARMS
Using the
1
OFF Key
....................................
36
Disarming the System
.......................................
36
Memory o
f Alarm
..................................................
36
19.
USING THE KEYSWITCH
General
......................................................................
37
Messages
.................................................................
37
Arming
.......................................................................
37
Disarming
................................................................
37
20.
CHIME MODE
Using the
9
Key
..............................................
38
Enabling the Chime
............................................
38
Disabling
the Chime
..........................................
38
21.
VIEWING ALARM COMPAN
Y MESSAGES
General Information
...........................................
39
22.
PANIC KEYS
Using Panic Keys
.................................................
40
Activate Panic Functions
.................................
40
Silent Emergency
.................................................
40
Audible Emer
gency
.............................................
40
Fire Alarm
.................................................................
40
iii
23.
SPEED KEY (MACROS)
General Information
............................................
41
Defining a Macro
..................................................
41
Executing
.................................................................
42
Automatic Macros
................................................
42
Manual Macros
.....................................................
42
24.
ACCESS DOOR CONTROL
General Information
............................................
43
Executing
.................................................................
43
25.
USING #70 RELA
Y MENU MODE
General Information
............................................
44
To activate relays from a keypad
..................
44
26.
USING SCHEDULES
Delaying the Closing Time
...............................
45
To delay the closing time
..................................
45
Temporary Open/Close Schedules
.............
46
27.
PROGRAMMING DEVICE T
IMERS
General Information
............................................
48
Randomize Output Device Times
................
50
28.
USING #77 INSTANT AC
TIVATION MODE
Relay Commands
.................................................
51
Arm/Disarm Commands
..................................
51
Bypass
Commands
.............................................
52
Open/Close Windows
........................................
52
Access Control Commands
.............................
52
Additional Commands
.......................................
53
To enter the Instant Activation Mode:
........
53
29.
EVENT LOG PROCEDURES
General Information
............................................
54
To Display the Event Log
..................................
54
30.
SETTING THE TIME AND
DATE
31.
TESTING THE SYSTEM
Using the
5
TEST Key
..................................
57
Testing Your System
..........................................
58
32.
FIRE
ALARM SYSTEM
General
......................................................................
59
In Case of Fire Alarm
..........................................
59
Silencing a Fire Alarm
........................................
59
33.
TROUBLE CONDITIONS
Typical Trouble Displays
..................................
60
Power Failure
.........................................................
61
SERVICING INFORMATION
............................
61
34.
RECOMMENDATIONS FOR PROPER
PROTECTION
Recommendations for Smoke and Heat
Detectors
.................................................................
62
Recommendations for Proper Intrusion
Protection
...................................................................
iii
35.
EMERGENCY EVACUATION
36.
MAINTAINING YOUR SYSTEM
Taking Care of Your System
...........................
65
Replacing Batteries in Wireless Sensors
. 65
Silencing Low Battery Warning Tones at the
Keypad
.......................................................................
66
Routine Care
..........................................................
66
37.
QUICK GUIDE TO SYSTE
M FUNCTIONS
38.
SUMMARY OF AUDIBLE N
OTIFICATION
39.
INDEX
iv
1
Section 1:
System Overview
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
General
Your Honeywell security system consists of a main control, at least one keypad, and various sensors
strategically positioned throughout the premises.
The system offers you three forms of protection:
burglary
, fire
and emerg
ency
. The keypad provides full control of system operation
.
The system uses microcomputer technology to monitor all protection zones
(doors, windows, smoke
alarms, etc.)
and system status. It
provides appropriate information for display on the keypad
(s) used
with the system, and initiates appropriate alarms. Your system may also have been programmed to
automatically transmit alarm or status messages over the phone lines
or cellular or IP communicator
to a central alarm moni
toring station.
This manual is designed to help you become comfortable operating your system. Each function is
explained in step
-by
-step detail. We recommend you read the
SYSTEM OVERVIEW
section to become
familiar with the terminology and the basic features of the system.
NOTE
S:
•
If you have a Graphic/Touch
-Screen Keypad
connected to your system, refer to the
Graphic/Touch
-Screen Keypad User Guide for operating instructions.
•
All references in this manual for number of zones, number of user codes, number of
access cards, and the event log capacity, use the
VISTA
-250BPT’s features.
•
The following table lists the differences between the VISTA
-128BPT/
VISTA
-128BPTSIA
and the VISTA
-250BPT
control panels. Additionally, only the VISTA
-128BPT/
VISTA
-
128BPTSI
A supports the capability to have a device duplicate keypad sounds at a
remote location. All other features are identical for both panels.
Feature
VISTA
-
128BPT
/
VISTA
-
128BPT
SIA
VISTA
-
250BPT
Number of Zones
128
250
Number of User Codes
150
250
Number of Access Cards
250
500
Event Log Capacity
512
1000
VistaKey Modules
8
15
2
System Overview (cont’d)
A Partitioned System
Simply stated, a partitioned system
shares one physical alarm system among different users, each
with their own requirements.
For the most part, you as a user need not know about other users and
their structure in the system, but from time to time, you may see displ
ay messages that indicate the
system is in use by another user. Do not be concerned, this is normal. Refer to the ACCESSING OTHER
PARTITIONS section for additional information.
Zones
Your system's sensing devices
have been assigned
to various "zones."
For example, the sensing device
on your Entry/Exit
door may have been assigned to zone 001, sensing devices on windows in the
master bedroom to zone 002, and so on. These numbers will appear on the d
isplay, along with an
alpha descriptor for that zone (if programmed), when a
fault,
alarm or trouble condition occurs.
Fire Protection
The fire protection
portion of your security system (if used) is always on and will sound an ala
rm if a
fire condition is detected. Refer to the FIRE ALARM SYSTEM section for important information
concerning fire protection, smoke detectors and planning emergency exit routes from your house.
Carbon Monoxide Protection
Carbon monoxide (CO) protection
is available with your system using the 5800CO Carbon Monoxide
Detector. The 5800CO is a 3V battery powered wireless Carbon Monoxide Detector used with wireless
alarm systems that support 5800 series devices.
Carbon monoxide gas is a highly poisonous gas
which is released when fuels are burned. It is invisible, has no smell and is therefore impossible to
detect with the human senses. We strongly suggest installing Carbon monoxide protection with your
system.
Alarms
When an alarm
occurs, both the keypad and external sounders will sound, and the keypad will display
the zone(s) causing the alarm. If your system is connected to a central monitoring station, an alarm
message will also be sent. To sto
p the alarm sounding, simply disarm the system.
The Swinger Suppression feature of your system limits the number of times a non-
fire zone locally
annunciates and transmits an alarm report to the central station. Ask your installer if this feature has
been
programmed.
3
System Overview (cont’d)
False Alarm Prevent
ion
Features
Cross Zoning and Swinger Suppression
Cross Zoning
and Swinger Suppression
, options can help reduce false a
larms.
•
Cross Zoning:
Requires activation of two zones within a specified time
window
to activate an alarm.
•
Swinger Suppression:
Limits the number of messages sent for a specific zone in
an
armed period. Swinger Suppress
ion is by zone and is
reset by
entering a valid
User Code + Off
.
Ask your instal
ler if your system is programmed for either of these features.
Abort Window
An Abort Window feature exists for all non
-fire zones. An Abort Window is a programmable time
window, which upon disarm (User Code + Off) after all non
-fire alarm occurs, will be prevented from
reporting if disarmed within said window.
NOTE:
Ask your installer if this feature has been programmed.
Keypad Locko
ut
•
If a user presses 30 numeric keys (0
-9) within a window of 15 minutes and no valid command is
executed, the system stops processing numeric key presses for a period of 15 minutes.
•
During this lockout period, the control responds to any numerical key press with a long beep.
•
In a partitioned system, a keypad that logs on to a locked out partition (using the GOTO
command) is locked out until the keypad is reconnected to its original partition, or until the
locked out partition’s lockout period expires, wh
ichever occurs first. NOTE: No keypad activity for
two minutes will result in the keypad logging back into its home partition.
•
When a 15
-minute lockout occurs, a message is recorded in the Event Log (WNG CODE ENT).
When the 15
-minute lockout window expire
s a WNG CODE RST message is recorded in the
Event Log.
Error Message Displayed
The displayed message on the keypad is as follows:
User Code Error
Key 0
-9 Locked
The display is cleared when the lockout period expires
, an
audible Alarm or the start of an Entry Time beginning.
4
System Overview (cont’d)
Burglary Protection
The burglary protection
portion of your system must be turned on or "armed"
before it will sense
burglary
alarm conditions. Your system provides four modes of burglary protection:
STAY
,
AWAY
,
INSTANT
and
MAXIMUM
,
and even allows you to
BYPASS
selected zones of protection while leaving
the rest of the system armed
. The system also provides a
CHIME
mode, for alerting users to the
opening and closing of doors and windows while the system is disarmed. Refer to the other sections of
this manual for procedures for using these features.
The following table lists the four different arming modes and the results of each.
Features For Each Arming Mode
Arming Mode
Exit
Delay
Entry
Delay
Perimeter
Armed
AWAY
Yes
Yes
Yes
STAY
*
Yes
Yes
Yes
INSTANT
*
Yes
No
Yes
MAXIMUM
Yes
No
Yes
∗
The system provides three different STAY and INSTANT arming modes. See
ARMING IN THE STAY MODES and ARMING IN THE INSTANT MODES sections for
details on these modes.
Memory of Alarm
When
an alarm condition occurs, the keypad displays the number(s) of the zone(s) that caused the
problem
or alarm
, and displays the type of alarm (ex. FIRE, ALARM). It remains displayed until it is
cleared by disarming the system (see
DISARMING THE SYSTEM
secti
on).
Speed Key (Macros
)
The system can store a string of up to 32 keystrokes, which can be activated anytime by simply
pressing the
“A, B, C, or D”
keys. This feature can be used to make it easy to perform multiple
functions at once (such as
going to another partition to bypass a zone), or it can be used to simplify an
everyday, repeated procedure. Refer to the
SPEED KEY
section for procedures for using this feature.
Using Schedules
Your system may have been programmed with schedules
for automatically arming, disarming and
activating various devices and/or performing other system functions at predetermined times. Users
can modify some of these schedules by manually delaying a closing time, using temporary schedules,
or by programming special user schedules. Refer to the
USING SCHEDULES
section at the end of this
manual for scheduling related procedures.
5
System Overview (cont’d)
Device Timers
The sys
tem provides up to 20 "timers" that can be used to control various devices, such as lights or
appliances. These timers are similar in concept to the individual appliance timers that might be
purchased at a department store. The devices that can be controll
ed are programmed into the system
by the installer. Up to 96 of these devices can be programmed. Refer to the
PROGRAMMING DEVICE
TIMERS
section for procedures.
Accessing
another
Partition (GOTO Command)
Each keypad is assigned a default partition for displ
ay purposes, and will show only that partition's
information. But, if the user is authorized, a keypad in one partition can be used to perform system
functions in another partition, by using the
GOTO
command
.
NOTE:
Only those partitions authorized and programmed by the installer can be
accessed in this
manner.
To
GOTO
another partition, enter your
USER CODE +
[
∗
] + PARTITION # (1
-8)
.
The keypad will remain
in the new partition until directed to go to another
partiti
on, or until two
minutes has elapsed with no
keypad activity.
Entering your
USER CODE + [
∗
] + [0]
will return the keypad to its original partition.
Master Keypad
Operation
A "Master" keypad is one on which the status of all eight
partitions is displayed simultaneously. A user
can get more information about a certain partition by simply entering
[
∗
] + PARTITION # (1
-8)
.
To log on to the "Master" partition (9) using the
GOTO
command, and to perform any functions at a
Master keypad
, a user must have access to all partitions.
Self
- Help Feature
Abbreviated user's instructions
are built into the system that can be easily viewed on the alpha
keypad's message display screen. This feature will prove particular
ly useful if this manual is not
conveniently accessible when you need to perform a system procedure with which you are not familiar.
Viewing Abbreviated Messages
Simply press and hold down the function key of interest until the description starts to appear (about 5
seconds) and then release it. The system must be
“READY TO ARM”
to perform this function.
Refer to the
FUNCTIONS OF THE KEYPAD
section for descriptions of each key function.
6
Section 2:
About The Keypads
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
General
IMPORTANT
!
If the keypad beeps rapidly upon entering the premises, it indicates that an alarm has occurred
during your absence.
LEAVE IMMEDIATELY and CONTACT THE POLICE
from a safe location
nearby.
NOTE
If you have a Touch Screen Keypad
connected to your system, refer to the
Touch Screen
Keypad
User Guide
for operating instructions.
Your keypads
allow you to control all system functions. The keypads feature a telephone style (digital)
keypad and a Liquid Crystal Display (LCD) that shows the nature and location of all occurrences.
Additional features include:
•
LCD b
ack lighting
is pro
grammable to always stay on or
light only when a key is pressed, then
turn off a few minutes later.
•
Built
-in sounder that will so
und during alarms and troubles. It will also "beep" during certain
system functions, such as during entry/exit delay times, CHIME mode, and when depressing
keys to perform system functions (to acknowledge the key press).
•
Built
-in
keypad
sounds
can be optionally suppressed (so as not to disturb other users of the
system). Ask your installer if this has been done.
The Alpha Keypad
Alpha keypads
feature a 2
-line, 32 character alphanumeric LCD that can display system messages in
user
-friendly English. Abbreviated user's instructions can also be displayed (see
Self Help
paragraph in
the
SYSTEM
OVERVIEW
section). These keypads can also be programmed with custom zone
descriptors.
7
Section 3:
Functions of the Keypads
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
IMPORTANT!
When
using the keypad to enter codes and commands, sequential key depressions must be made
within 3 seconds of one another. If 3 seconds elapses without a key depression, the entry is aborted
and must be repeated from its beginning.
In addition, if the user enters more than 30 numeric keys (0
-9) within a 15
-minute window and a
valid command is not executed, the system stops processing additional numeric key presses for 15
minutes.
Any numerical key press during the lockout generates a long beep
. This is a
programmable option that must be configured by the installation company.
8
Functions
of
the
Keypad (cont’d)
ALPHA DISPLAY WINDOW
is a
2-line, 32
-character Liquid Crystal Display (LCD)
that
displays
protection point identification and system status, messages, and user instructions.
A
1
1
O
O
F
F
F
F
Disarms the burglary portion of the system,
silences alarms and audible trouble indicat
ors,
and clears visual alarm trouble after the
problem has been corrected.
A
2
2
A
A
W
W
A
A
Y
Y
Completely arms both perimeter and interior
burglary protection by sensing an intruder's
movements through protected interior areas as
well as guarding protected doors, windows, etc.
Late arrivals can enter through an entry delay
zone without causing an alarm if the system is
disarmed before the entry delay time expires.
A
3
3
S
S
T
T
A
A
Y
Y
Arms the perimeter burglary protection,
guarding protected doors,
windows and other
perimeter protection points, and sounds an
alarm if one is opened. Also a
llows automatic
bypassing of certain areas which permits
movement within your house without causing
an alarm. Late arrivals can enter through an
entry delay zone wi
thout causing an alarm if the
system is disarmed before the entry delay time
expires. See
ARMING PERIMETER ONLY
for a
full explanation of the STAY key.
A
4
4
M
M
A
A
X
X
Arms in manner similar to AWAY mode, but
eliminates the entry delay period, thus
providing maximum protection. An alarm will
occur immediately upon opening any
protection point, including entry delay zones.
A
5
5
T
T
E
E
S
S
T
T
Tests the system and alarm sounder if
disarmed.
A
Removes individual protection zones f
rom
being monitored by the system. Displays
previously bypassed protection zones.
A
7
7
I
I
N
N
S
S
T
T
A
A
N
N
T
T
Arms in manner similar to STAY mode, but turns
off the entry delay period, offering greater
security while inside and not expecting any late
arrivals.
An alarm will occur immediately upon
opening any perimeter protection point,
including entry delay zones.
A
8
8
C
C
O
O
D
D
E
E
Allows the entry of additional user codes that
can be given to other users of the system.
9
Functions of the Keypad (cont’d)
A
9 CHIME
Turns on & off the CHIME mode. When on, any
entry through a protected delay or perimeter
zone while the system is disarmed will cause a
tone to sound at the Keypad(s).
A
∗
READY
E
When depressed prior to arming the system, the
keypad will display all open protection zones
within the keypad's home partition. This key is
also used to display all zone descriptors that
have been programmed for your system, by
holding the key down for at least 5 seconds.
A
#
Permits ARMING of the system without use of a
security code (
"Quick Arm
"
, if programmed).
KEYS 0
-9
Used to enter your individual security access
code(s).
LED READY INDICATOR
(GREEN) Lit indicates system is ready to be
armed, while unlit indicates system not ready.
LED
ARMED INDICATOR
(RED) Lit when the system has been armed
(STAY, AWAY, INSTANT or MAXIMUM).
SPEAKER
Source
of audible internal warning and
confirmation sounds, as well as alarms (see
"Summary of Audible Notifications").
FUNCTION KEYS
These keys can be used for Speedkey (macros)
functions or panic keys. Refer to the
SPEEDKEY
(MACROS)
and
PANIC
KEYS
sections for
descriptions of these functions.
10
Section 4:
Entry/Exit Delays
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
General Information
Your system has installer
-programmed time delays, known as
Exit D
elay
and
Entry D
elay
.
Exit
Delay
Whenever you arm your system
(Away, Stay, Instant, or Maximum),
an
exit delay
g
ives you time to leave
through the designated exit doo
r without setting off an alarm.
NOTE:
Exit delay begins immediately after entering any arming command, and applies to all modes
of arming protection. If programmed, a slow beeping will sound throughout the exit delay
period.
Entry Delay
An
entry delay
gives you time to disarm the system when you reenter through the designated entrance
door.
NOTES
•
The system must be disarmed before the entry delay period ends, or an alarm will occur.
•
The keypad will beep during the entry delay period, reminding you to disarm the system.
•
You can also arm the system with no entry delay at all by
using either INSTANT
or MAXIMUM
arming modes. These modes provide greater security while on the premises or while away for
extended periods of time. See your installer for your delay times.
Defaults and Requirements
As a requirement of SIA
-CP
-01,
Entry Delay
is 30 seconds and
Exit Delay
is 60 seconds.
Exit Delay Reset
As a requirement of SIA
-CP
-01, a
n
Exit Delay Reset
is designed to allow a user to re-
enter the premises
to retrieve a forgotten item without triggering an alarm. This feature may only be activated
once
after
arming.
If enabled, when the panel is armed, the normal exit delay begins. After the user exits, closes
the door
and then re-
enters the premises, the exit delay time is reset to the programmed value.
Burglar Alarm Communication Delay
As a requirement of SIA
-CP
-01, there is a communicator delay of 30 seconds in this control panel. This
delay will prevent a r
eport to the central station if the control panel is disarmed within 30 seconds after
an intrusion alarm is triggered. This delay can be removed, or it can be increased up to 45 seconds at
the option of the user by consulting with the Installer.
Note that fire
-type alarms are normally reported
without delay.
11
Section 5:
Security Codes and
Authority
Levels
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
General Information
At
the time of installation, you were assigned a personal four
-digit security c
ode, known only
to you
and yours
, assigned to one of six authority levels
. The security code must be entered when arming and
disarming the system. The authority level defines the system functions that you can perform.
•
As an additional safety feature, other users that do not have a need to know your code can be
assigned different codes, and each user can be given a different authority level.
•
Users are identified by
three digit
"user numbers"
, which are assigned when assigning a user's
security code.
•
All codes can be used interchangeably when performing system functions within the limits of
each code's authority level (a system armed with one user's code can be disarmed by another
user's code), with the
exception of the Operator Level C
code. See
AUTHO
RITY LEVELS
on the
following page for details regarding authority levels.
Duress Code
This feature is intended for use if you are forced to disarm or arm the system under threat. When used,
the system will act normally, but can silentl
y notify the central station of your situation, if that service
has been provided. The duress code is pre-
assigned by the installer during installation (authority level
six
).
Important
!
This code is useful only when the system is connected to a central station.
Quick Arming
Note that if "Quick Arming" was programmed by the installer, the
A
#
E
A
key can be pressed in place of
the security code when arming the system. The security code
must
always
be use
d to disarm the
system, however.
Installer Code Lockout
If the Installer Code Lockout option has been enabled, the installer may only
enter the program mode
for a period of 24 hours
following the installation. Once the 24
-hour period has expired the installer
can only enter the
program mode if the Master user enables access by entering
Master User + #65
.
This opens another 24
-hour window in which the installer may enter program mode.
12
Security Codes and
Authority Levels (cont’d)
Authority Levels
Authority levels
define the system functions a particular user can perform. Depending on the authority
assigned to you, there are certain system functions you may be prohibited from perfo
rming.
In summary, there are six authority levels, each having certain system restrictions as shown below.
L
L
e
e
v
v
e
e
l
l
1
1
M
M
a
a
s
s
t
t
e
e
r
r
:
:
Can perform all system functions in assigned partitions, and can add,
delete or change Manager and all
Operator
level users
, as well as
change
its own code
. However, the Master Code cannot assign a user
to the Master authority level.
Master codes
only
are
added by the
Installer.
L
L
e
e
v
v
e
e
l
l
2
2
M
M
a
a
n
n
a
a
g
g
e
e
r
r
:
Can perform system functions in assigned partitions, and can add,
delete
or change Operator level users
three, four, or five
.
NOTE:
The manager authority level does not have the ability to
assign
any user an authority of one (master) or two
(manager).
L
L
e
e
v
v
e
e
l
l
3
3
O
O
p
p
e
e
r
r
a
a
t
t
o
o
r
r
A
A
:
:
Can
perform
Arming, Disarming, and Bypassing
in assigned
partitions, but
cannot
add
or delete other users.
NOTE:
Can be assigned to any user number 003
-150.
L
L
e
e
v
v
e
e
l
l
4
4
O
O
p
p
e
e
r
r
a
a
t
t
o
o
r
r
B
B
:
:
Same as Operator A, except Operator B cannot
bypass zones.
NOTE:
Can be assigned to any user number 003
-150.
L
L
e
e
v
v
e
e
l
l
5
5
O
O
p
p
e
e
r
r
a
a
t
t
o
o
r
r
C
C
:
:
Can arm the system in assigned partitions, but cannot disarm the
system
unless
the system was armed with this code. This code is
typically assigned to someone who has a need to arm/disarm the
system only at certain times (such as a baby
-sitter).
L
L
e
e
v
v
e
e
l
l
6
6
D
D
u
u
r
r
e
e
s
s
s
s
:
:
Can arm and disarm the system, but also sends a silent
panic alarm to
the central station, if that service is connected.
To view your authority level and system capabilities:
1.
Enter your User Code
+
∗
+
∗
.
2.
The keypad will display the partition(s) that you are authorized to operate, and your user
number and authority level in each partition.
13
Security Codes and Authority Levels (cont’d)
Authority Levels
and Changes
•
A user may not delete or change the user code of the
SAME
or
HIGHER
authority than which he
is assigned.
•
A user may only
ADD
users to a
LOWER
authority level.
•
A user may assign access codes only to those partitions to which the user adding the code has
acc
ess. (
Ex. a user with access to only partition 1 cannot assign codes in partition 2.)
•
The only way to assign a user's authority level is by using the
"Add
a User
"
procedure.
To change a
user's
authority
level, that user must first be deleted,
and then
added again.
•
A user can only be
DELETED
or
CHANGED
from within the partition he is assigned.
•
User numbers must be entered as 3
-digit entries. Single digit u
ser numbers must be preceded
by a "00" (example, 003, 004, etc.). Security codes are entered as 4
-digit numbers.
•
Before assigning a security code, be sure it does not conflict with any
DURESS
code.
NOTE:
When adding, changing or deleting users, all other
alpha keypads in that partition will
display "U
ser Edit Mode
– Please Stand By", and
key depressions (except Panic) at
those keypads will be ignored
. Panic key depressions will cause an alarm and terminate
user entry.
To Exit Us
er Edit Mode
You can exit any of the user edit modes described on the following pages at any time by doing the
following:
1.
Press either
∗
or
#
or don't press any key for 10 seconds.
2.
System returns to
normal mode.
14
Security Codes and
Authority Levels (cont’d)
To Add a User
IMPORTANT!
Temporary users
should not be shown how to use any system function they do not need to
know (e.g. bypassing protection zones).
1.
Enter Master or
Manager code
+
8
CODE
key.
2.
Enter the new user's 3
-digit User Number (002-
250).
3.
Enter 4
-digit security code for that user.
Assuming you want to program user 003 as 5678 using the master code of 1234, the syntax reads as
follows:
1234 +
8
CODE
+ 003 + 5678
Once entered the following prompts will appear.
ADD NEW USER?
0 = NO , 1 = YES
Enter
1
to add a new user code.
NOTE:
Entering
0
will change the existing user's code to the
code entered in step 3. See
Changing A User's Code
section.
USER NUMBER = 003
ENTER AUTH. LEVEL
Enter the authority level, 1
-
6, for this user within this partition.
1 = M
aster
2 = M
anager
3 = Operator A
4
=
O
perator B
5
=
O
perator C
6
=
D
uress code
Group BYPASSING?
0 = NO , 1 = YES
Enter
1 (YES)
to allow this user to perform group bypasses.
Enter
0 (NO)
this user will not be able to perform group
bypasses.
Access Group?
Enter 0
-8
If Access S
chedules have been programmed, this prompt
appears. Enter the user's access group number (1
-8) if this
user should have limited access to the system.
Enter 0 if no access group should be assigned.
RF BUTTON
?
0 = NO , 1 = YES
This prompt will appear if a 5800 series
wireless key
transmitter
has been supplied and has not yet been assigned to a user.
Press 1 if a button transmitter will be assigned to this user.
Otherwise press 0.
NOTE
:
This requires the three-
digit zone number f
or the
wireless
key provided by the installer.
ENTER BUTTON ZN #
(001
-250)
If assigning a wireless key
button
, this prompt will appear.
(Note
each wireless key button is assigned to zone.)
Enter the button's
zone number.
NOTE
:
This requires the three-
digit zone number for the
wireless
key provided by the installer.
15
Security Codes and
Authority Level
s (cont’d)
MULTI-
ACCESS
?
0 = NO , 1 = YES
If a user have access to other partitions, the keypad will prompt for
ability of this new user to access (GOTO
) those partitions.
Press
0 (NO)
, the system activates this user code
and exits “Add a
User” mode.
1 (YES)
, the keypad prompts for the Global Arm option for this user.
GLOBAL ARM
?
0 = NO , 1 = YES
Press
1 (YES)
if this user will be allowed to try to arm more than one
partition at the same time.
Press
0
if this user will arm only their
assigned partition.
PART.2
- SHOP?
0 = NO , 1 = YES
The keypad now prompts for the user’s access to the next partition
(see GOTO command).
If yes, the system will automatically assign a user number for use in
that partition and will prompt for authority level and global arm
options for this user within the partition (see previous steps).
Part. 1 A0* WHSE
User 003 Auth=3G.
When all partitions have been displayed, the keypad will scroll
through the partition(s) to which access has been assigned, and
display
s the user number, authority level and global arm option for
each.
NOTES
•
The “G” after the authority level indicates that the G
lobal
Arm feature is active for this user in the displayed partition.
•
The
“
∗
” indicates the partition from which this user can be
changed or deleted. The “.”
at the end of the second line
indicates that this user sends open/close reports.
•
If the Master or
Manager have
Open/close reporting
enabled, Open/Close
is automatically active for any users
added by you
.
16
Security Codes and
Authority Levels (cont’d)
To Change a User's Code
1.
Enter Master or Manager
Code
and press the
A
8
CODE
key + user number to be
changed.
2.
Enter the new code for that user.
Assuming you want to reprogram user 003 from 5678 to 6789 using the master code of 1234, the
syntax reads as follows:
1234 +
8
CODE
+ 003 + 6789
Once entered the following prompts will appear.
ADD NEW USER
?
0 = NO , 1 = YES
The system recognizes
that the user number is already in use
and will prompt whether or not this is a new user.
Enter 0 to change the existing user's code.
USER 002 CHANGED
SUCCESSFULLY
The system will confirm that the change is allowed based on
authorization level, and if so, will put the new code into effect.
NOTE:
If changing one’s own code
,
the system will prompt for
the new code to be re-
entered. This prevents
accidentally changing one's own code.
17
Security Codes and
Authority Levels (cont’d)
To Delete a User
1.
Enter Master or Manager
Code
and press the
A
8
E
CODE
E
A
key + user number to be deleted.
2.
Enter Master or Manager
Code
first entered.
Assuming you want to delet
e user 003 using the master code of 1234, the syntax reads as follows:
1234 +
8
CODE
+ 003 + 1234
Once entered the following prompts will appear.
OK TO DELETE
0 = NO
, 1 = YES
The system will recognize that the User number is already in use and
will prompt to confirm that it should be deleted.
Press 0 (NO) or 1 (YES).
USER CODE
DELETED
If yes, that user's code will be removed from all partitions to which it
was assigned, and all authorization levels and other information
about that user will be deleted.
NOTE:
A User's security code cannot be deleted by oneself.
Important!
Note that a user can only be deleted from the partition in which it
was first assigned, and can only be deleted by a user with a higher
authority level.
18
Section 6:
Accessing Other Partitions
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
To Access
another
Partition
(GOTO)
Each keypad is assigned a default partition for display purposes, and will show only that partition's
information. But, if the user is authorized, a keypad in one partition can be used to perform system
functions in other partitions by using the
GOTO
comma
nd.
NOTE:
Only those partitions authorized and programmed by the installer can be accessed in
this
manner.
To GOTO
another partition:
1.
Enter
your security code, then press
A
∗
A
+ partition number (0
-8).
2.
Entering partition number 0
will return the keypad to its original partition.
Assuming you want to log onto partition 3 using the master code of 1234, the syntax reads as follows:
1234 +
∗
READY
+ 2
LOG
-ON TO AAAA
PART. X COMPLETE
The keypad will remain in the new partition until directed to go
to another partition, or until 2 minutes has elapsed with no
keypad activity.
AAAA = Alpha descriptor programmed by the installer.
X = Partition Number
19
Section 7:
Global Arming
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
The Global Arming
option may be assigned for use by some users. If Global Arming was enabled for
use with your security code, a keypad prompt (message) shown below appears after pressing one of
the arming function keys (STAY
, INSTANT
, AWAY
, MAXIMUM
, OFF).
ARM P12345678
HIT 0
-8 XXX--
X --
The prompt displays all the partitions. The user may only
arm/disarm the partitions they are assigned access to.
To select the partition(s) that are to be armed
(or disa
rmed)
,
enter the desired number 1
-8. An "X" will appear under that
partition. Entering a partition's number again will delete the “X”
and that partition will not arm when this prompt is exited.
NOTE:
Pressing 0 will turn all partitions the user is assign
ed
access
to On/Off.
When completed, press
∗
to exit. All the partitions with the “X”
will then arm/disarm.
Global Arming Notes
Global Arm
When performing a
Global Arm
, if there are faults in any of the selected partitions, the system will
enter a
Summary Mode
. Faulted zones in all the selected partitions will be displayed. These faults must
be corrected or bypassed. This Summary Mode will end in approximately 120 seconds if no keys are
pressed.
Global Disarm
When performing a
Global
Disarm
, if any of the selected partitions has a condition which would cause
the keypad to beep (e.g., alarm memory or a trouble condition), the system enters a
Summary Mode
and displays the condition.
NOTE:
This Summary Mode will end in approximately 120 seconds if no keys are pressed.
20
Section 8:
Master Keypad
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Operation
A Master
keypad is one that reflects the status of the entire system (Partitions 1
-8) on its display. This
is useful because it
eliminates the need for a building, campus, etc. security officer
the process of
logging on
to various partitions from one partition's keypad to find out where an alarm
, trouble, etc.
has occurred.
A description of a typical display follows:
SYSTEM
1 2 3 4 5 6 7 8
STATUS
R R N N A T
∗
B
The status of each partition is directly below the partition number on the display. Possible status
indications include:
A
=
Armed Away
S
= Armed Stay
M
= Armed Maximum
I
= Armed Instant
R
=
Ready
N
=
Not Ready
B
= Bypassed/Ready
∗
= Alarm
T
= Trouble
F
=
Fire Alarm
P
=
AC Power Failure
L
= Low System Battery
C
= Comm Fail
To obtain more information regarding a particular partition, enter [
∗
] + [Partition No.] (i.e
.,
∗
4). This will
allow viewing
only
of that partition.
In order to affect that partition, the user must log on with a code that has access to that partition.
Also, in order for a user of any partition to log onto the "Master" partition (Partition 9) to view the status
of
all
partitions,
and to perform any functions at the Master keypad, that user must have access to all
partitions. Otherwise, access will be denied.
21
Master Keypad (cont’d)
The fo
llowing is an example of what would be displayed for a fault condition on Zone 002 (Loading
Do
ck Wi
ndow) on Partition 1 (Warehouse) when logging on from a keypad on Partition 9:
WHSE DISARMED
HIT
∗
FOR FAULTS
This is the n
ormal display that appears at Partition 1's keypad(s). Pressing
∗
will display:
FAULT 002 LOADING
DOCK WINDOW
Additional zone faults will be displayed one at a time. To display a new partition's status,
press
∗
+
[Partition No.]
(no user code required)
. This will display the status of the new
partition.
•
The "Armed" LED on a Master keypad will be lit only if
all
partitions have been armed
successfully.
•
The "Ready" LED will be lit only if
all
partitions are "ready to arm."
The sounder on a Master keypad will reflect the sound of the most critical condition on all of
the
partitions. The priority of the sounds is
as follows:
1.
Pulsing fire alarm sounds
2.
Steady burglar alarm sounds
3.
Trouble sounds
The sounder may be silenced by pressing any key on the Master keypad.
22
Section 9:
Common Lobby
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Operation
When an installation consists of a partition that is shared by users of
an
other partition
(s)
in a building,
th
e shared partition may be assigned as a
“
Common L
obby”
partition for the system.
An example of this might be in a medical building where there
are two doctors and a common
entrance area.
This option employs logic for automatic arming and disarming of the common lobby.
Partitions may be set to affect and/or attempt to arm the common lobby. This will affect the way the
lobby will react when armi
ng or disarming activity occurs in another partition.
Affecting the Lobby (Disarming)
Partitions that
affect
the lobby will cause the following to occur:
•
When the first partition that affects the lobby is disarmed, the lobby will also be disarmed.
•
The comm
on lobby cannot be armed unless every partition selected to affects the lobby is
armed.
•
Arming the last partition that affects the lobby
will not
automatically attempt to arm the lobby.
•
When the first partition that affects the lobby is disarmed, the lobb
y will also be disarmed.
Arming the Lobby
Partitions set to
Ar
m
the lobby will cause the following to occur:
•
The common lobby cannot be armed unless every partition selected to affects the lobby is
armed.
•
Arming the last partition programmed to arm the lobby will automatically attempt to arm the
lobby.
NOTE:
If any faults exist in the lobby partition, or another partition that affects the
lobby is
disarmed, the lobby cannot be armed, and the message “
UN
ABLE TO ARM LOBBY
PARTITION”
will be displayed.
The following chart summarizes how the common lobby partition will operate:
Partition
Affects
Lobby
Partition Arms
Lobby
Disarms When
Partition Disarms
Attempts to Arm
When
Partition
Arms
Can Be Armed if
Other Partitions
Disarmed
NO
NO
NO
NO
YES
YES
NO
YES
NO
NO
YES
YES
YES
YES
NO
NO
YES
---
ENTRY NOT ALLOWED
---
23
Common Lobby (cont’d)
How User Codes Affect the Common Lobby
Codes with “Global” Arming
If your code is given “global arming” when it is defined, the system displays a prompt that allows you to
pick and choose the partitions to be armed or disarmed. This eliminates the “automatic” operation of
the lobby.
NOTE:
Keep in mind, however, that if
attempting to arm all the partitions you have access to,
and
another affecting partition is disarmed, (one you do not have access to) you will not be able to
arm the lobby, and the message
“UNABLE TO ARM LOBBY PARTITON”
will be displayed.
Codes with “N
on
-Global” Arming
If arming with a non-
global code, the lobby partition operation will be automatic, as described in the
previous table.
Other Methods of Arming/Disarming
When arming or disarming a partition that affects and/or arms the common lobby in one
of the
following manners, lobby logic remains active:
•
Quick
-Arm
•
Keyswitch
•
Wireless
Key (keychain remote)
•
Wireless Keypad
24
Section 10:
Checking For Open Zones
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Using the
∗
READY
Key
Before arming your system, all protected doors, windows and other protection zones must be closed or
bypassed (see
BYPASSING
section). Otherwise the keypad will display a "Not Ready
" message. Using
the
READY
key
will display all zones that are faulted, making it easier to secure any open zones.
Showing Faulted Zones
1.
DISARMED
- PRESS
∗
TO SHOW FAULTS
NOTE:
Some keypads light a green LED when the system is
ready. If not lit, the system is not ready to be armed.
2.
Do
not
enter security code, but simply
Press
∗
READY
3.
FAULT 005 FRONT
UPSTAIRS BEDROOM
Typical
fault display
4.
****DISARMED
****
READY TO ARM
Secure or bypass the zones displayed before arming the
system.
The "Ready" message will be displayed when all protection
zones have been either closed or bypassed.
NOTE:
All or part of this message
may
be replaced by a
customized message programmed by the
installer.
Bear this in mind whenever the
instructions indicate that the "DISARMED" or
"READY" message will be
displayed.
25
Section 11:
Displaying All Zone Descriptors
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Using the
∗
READY Key
The Alpha Keypads can also display all the zone descriptors
that are programmed in your system. The
abbreviated instructions for the
READY
key will appear first, followed by the zone descriptors.
Displaying all descriptors
is useful when you need to know the zone number of a particular zone, as
when bypassing zones.
The "Disarmed
-Ready to arm" message must be displayed before zone descriptors can be displayed.
Displaying D
escriptors
Press the
A
∗
E
READY
E
A
key and hold down for at least 5 seconds.
26
Section 12:
Bypassing Protection Zones
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Using the
6
BYPASS Key
This key is used to arm your system with one or more zones intentionally unprotected.
•
Bypassed zones are unprotected and will not cause an alarm when violated while your system is
armed.
•
All bypasses are removed when an OFF sequence (security code plus O
FF) is performed.
NOTE
:
The system will not allow fire or emergency zones to be bypassed.
To Bypass
1.
Enter your
Security Code +
6
BYPASS
2.
Enter zone number(s) for the zones to be bypassed (e.g., 001, 002, 003, etc.).
Important!
All single
-digit numbers must be preceded by “00” (for example, enter 001 for zone 1).
3.
Press
[
∗
] + [
∗
].
4.
BYPASS 007 FRONT
UPSTAIRS BEDROOM
Typical bypass message
When finished, the keypad will display the word BYPASS
along with each bypassed zone
number. Wait for these
zones to be displayed before arming. Arming the system
before bypassed zones are displayed eliminates all
bypasses.
5.
DISARMED BYPASS
READY TO ARM
Arm the system as usual when the keypad displays "ready"
to arm message.
27
Bypassing Protection Zones (cont’d)
Quick Bypass
Your system allows you to easily bypass all open (faulted) zones without having to enter zone numbers
individually.
NOTE:
All bypasses are removed when an OFF sequence (security code pl
us OFF) is
performed.
Quick Bypassing
1.
Enter your
Security Code +
6
BYPASS
+
#
2.
BYPASS 007 FRONT
UPSTAIRS BEDROOM
Typical bypass message
In a few moments, all open zones will be displayed along with
the word BYPASS. Wait for these zones to be displayed
before arming. Arming the system before bypassed zones
are displayed eliminates all bypasses.
3.
DISARMED BYPASS
READY TO ARM
Arm the system as usual when the keypad displays the
"ready" to arm message. Bypassed zones
are unprotected
and will not cause an alarm when violated while your system
is armed.
Viewing Bypassed Zones
The system allows you to view bypassed zones that are presently bypassed regardless of the status of
the partition (armed, disarmed, etc.). To vie
w bypassed zones.
1.
Enter your security code + # + 84.
2.
All zones presently bypassed are automatically scrolled for display.
28
Bypassing Protection Zones (cont’d)
Group Bypass
Your system allows you to easily bypass a group of zones without having to enter zone numbers
individually. The system provides up to 15 groups. There is no limit to the number of zones that may be
assigned to any one group.
Check with your installer for
a list of zones assigned to the group(s).
NOTES
All bypasses are removed when an OFF sequence (secur
ity code plus OFF) is performed
, except if it is
programmed otherwise (see
“Zones Remaining Bypassed After Disarm”
section.
Users must be assigned the follo
wing attributes to perform the group bypass function:
•
Enabled for group bypassing
•
Access to the partition(s) containing the zones being bypassed
•
Global
arming
capability
if the zones in the group are in multiple partitions
.
Bypassing
Group
s
1.
Enter your
User Code +
6
BYPASS
+
∗
READY
then enter the group number (01
-15).
2.
BYPASS 007 FRONT
UPSTAIRS BEDROOM
Typical bypass message
In a few moments, all the zones in the group will be displayed
along with the word BYPASS. Wait for these zones to be
displayed before arming. Arming the system before
bypassed zones are displayed eliminates all bypasses.
3.
DISARMED BYPASS
READY TO ARM
Arm the system as usual when the keypad displays the
"ready" to arm message.
Bypassed zones are unprotected
and will not cause an alarm when violated while your system
is armed.
29
Bypassing Protection Zones (cont’d)
Zones Remaining Bypassed After Disarming
The system provides an option to allow all manually bypassed zones to remai
n bypassed upon
disarming (security code + OFF) of the partition. Check
with your installer to see if this option has been
enabled.
NOTES
For each partition in which the option is enabled, the security code + OFF will no longer unbypass
zones.
•
To unbypass ALL zones you must
enter your security code + # + 64
.
•
To unbypass zones INDIVIDUALLY, you must enter your security code + 6 + zone number.
•
Any zone that was automatically bypassed by the system will be unbypassed upon disarming the
system (e.
g. STAY mode, Auto
-STAY, etc.).
•
Vent zones and zones bypassed by a programmed Auto
-Bypass schedule (T
ime Driven Event)
are considered “manual bypasses” and will not be unbypassed upon disarming the system.
30
Section 13:
Arming
Stay with
Entry Delay
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Using the
3
STAY key
Use this key when you are staying home, but might expect someone to use the entrance door later.
Operation
Armed Stay consists of the following attributes:
•
System
protects all exterior zones such as doors and windows
•
System does
NOT
protect interior zones such as motion detectors allowing you to move freely
through the premise
•
Arming Stay
always
has an exit (giving you time to leave) and entry delay (giving you time
to
enter. If you enter the zone through a zone marked as an entry point you must disarm before the
entry time period expires before an alarm occurs. If you enter through a non
-entry protected
zone an alarm will occur.
Stay Modes
The system provides three STAY modes conveniently labeled Stay Mode 1, 2, and 3.
•
When activated, STAY modes 1 and 2 automatically bypass specific zones assigned by your
installer to each of the STAY modes
•
If there are only Stay 1 zones, entering
Code +
3
STAY
A
will automatically arm in Stay Mode 1
•
If at least one zone assigned to Stay Mode 2, you
MUST
choose to arm in mode 1, 2, or 3 (see
below), else the panel will not arm
•
If
Code +
3
STAY
A
is entered Stay Mode 1 prevails (even if there ar
e Stay Mode 2 zones).
31
Arming STAY with Entry Delay (Cont’d)
Arming STAY
Check with your installer for a list of the zones that are bypassed during each STAY mode. Before
arming
close all perimeter windows and doors (see
CHECKING FOR OPEN ZONES
section).
1.
Enter you
r
User Code
+
3
STAY
+
1
for STAY Mode 1,
3
STAY
+
2
for STAY Mode 2
, or
or
3
STAY
+
3
for STAY Mode 3
2.
ARMED ***STAY 1*
ZONE BYPASSED
The keypad beeps three times, displays the armed message,
and indicates which STAY mode (1, 2 or 3).
Note:
"ZONE BYPASSED
" in this display simply indicates that
some zones of protection are not armed when using STAY
mode.
Auto
- STAY
Arming
Auto
-stay allows the system to automatically bypass certain zones if upon arming none of the
entry/exit zones are faulted during the exit delay time (no one exits the premises). The system provides
an option to set each burg
lary zone for Auto-
stay.
All zones enabled for auto
-stay except for perimeter and day/night types of zones, have
exit delay time
when the partition is armed.
Check with your installer for the zones assigned for Auto
-STAY.
NOTE
S:
•
Auto
-STAY applies to all four arming modes (AWAY, STAY, INSTANT and MAXIMUM).
•
Arming the partition AWAY via an RF transmitter overrides the Auto
-stay feature (partition will
not bypass zones programmed for auto
-stay).
32
Section 14:
Arming
Stay with NO Entry Delay
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Using the
7
INSTANT Key
Important
!
If you are using a Graphic/Touch
-Screen Keypad
,
NIGHT
mode is the same as INSTANT.
Use this key when you are staying home and do not expect anyone to use the entrance door.
Operation
When armed in INSTANT mode, the system will sound an alarm if a protected door or window is
opened, but you may otherwise move freely throughout the premises. The alarm will also sound
immediately if anyone opens the entrance door.
Instant Modes
The system provides three INSTANT modes
; INSTANT mode
s 1, 2 and 3.
•
INSTANT modes 1 and 2, when activated, automatically bypass specific zones assigned by your
installer to each o
f the INSTANT modes.
•
INSTANT mode 3, when activated, automatically bypasses all zones assigned to INSTANT modes
1 AND 2.
Check with your installer for a list of the zones that are by
passed during each INSTANT mode.
Arming INSTANT
Before arming close all
perimeter windows and doors before arming (see
CHECKING FOR OPEN
ZONES
section)
1.
Enter you
r User Code
+
A
7
E
INSTANT
E
A
+
A
1
E
E
A
for
INSTANT
Mode 1,
A
7
E
INSTANT
E
A
+
A
2
E
E
A
for
INSTANT
Mode 2
,
or
A
7
E
INSTANT
E
A
+
A
3
E
E
A
for
INSTANT
Mode 3
2.
ARMED ***STAY 1*
ZONE BYPASSED
The keypad beeps three times, displays the armed message,
and indicates which INSTANT
mode (1, 2 or 3).
Note: "ZONE
BYPASSED
" in this display simply indicates that
some zones of protection are not armed when using INSTANT
mode.
NOTE:
If none of the zones in a partition are assigned to INSTANT mode 2, then when the user
enters
User Code
+
7
INSTANT
, all zones assigned to INSTANT mode 1 are automatically
bypassed.
33
Section 15:
Arming All Protection
(with Entry
Delay)
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
(with Entry Delay)
Using the
2
AWAY Key
Use
this key when no one will be staying on the premises.
Operation
When armed in AWAY mode, the system will sound an alarm if a protected door or window is opened,
or if any movement is detected inside the premises.
•
You may leave through th
e entrance door during the exit delay p
eriod without causing an alarm
•
You may also re
-enter through the entrance door, but must disarm the system within the entry
delay period or an alarm will occur
Arming Away
Close all perimeter windows and doors before arming (see
CHECKING FOR OPEN ZONES
section).
1.
Enter your
User Code +
2
AWAY
2.
ARMED **AWAY**
YOU MAY EXIT NOW
The keypad will beep twice and will display the armed
message.
NOTE:
The "YOU MAY EXIT NOW" portion of the
message
disappears when exit delay expires.
34
Section 16:
Arming All Protection
(No Entry
Delay
)
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Using the
4
MAXIMUM Key
Use this key when the premises will be vacant for extended periods of time such as close of business
for holidays, etc.
or when no one will be moving through protected interior areas.
Operation
When armed in MAXIMUM mode, the system wi
ll sound an alarm if a protected door or window is
opened, or if any movement is detected inside the premises.
You may leave through the entrance door during the exit delay period without causing an alarm, but
an alarm will be sounded as soon as someone r
e-enters.
Arming MAXIMUM
Close all perimeter windows and doors before arming (see
CHECKING FOR OPEN ZONES
section).
1.
Enter your
User Code +
4
MAX
2.
ARMED *MAXIMUM*
YOU MAY EXIT NOW
The keypad will beep twice and will display the armed
message.
NOTE:
The "YOU MAY EXIT NOW" portion of the
message disappears when exit delay expires.
35
Section 17:
Quick Exit
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Using the
#
+
9
Keys
The Quick Exit
feature allows you to exit the armed partition without having to disarm and then rearm
the partition.
Arming with Quick Exit
Enter your
User Code +
#
+
9
The
system will sound the exit beeps, if enabled, and will give you the programmed exit
delay time to leave the premises.
36
Section 18:
Disarming
and
Silencing Alarms
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Using the
1
OFF Key
The
OFF
key is used to disarm
the system and to silence alarm and trouble sounds. See
"
SUMMARY OF
AUDIBLE NOTIFICATION
"
section for information which will help you to distinguish between FIRE and
BURGLARY alarm sounds.
IMPORTANT
!
If you return and the main burglary sounder is on,
DO NOT
enter the premises, but call the
police from a nearby safe location. If you return after an alarm has occurred and the main
sounder has shut itself off, the keypad will beep rapidly upon entering, indicating that an
alarm has occurred during your absence.
LEAVE IMMEDIATELY
and
CONTACT THE POLICE
from a nearby safe location.
Disarming the System
To disarm the system and silence burglary or fire alarms:
1.
Enter your User Code +
1
OFF
2.
****DISARMED****
READY TO ARM
The Ready message displays (if no alarms have occurred
while armed) and the keypad beeps once to confirm that the
system is disarmed.
IMPORTANT!
It is not necessary to press the “OFF” key on the keypad to disarm the system when it is in
entry delay or alarm.
Entering a valid user code alone causes the system to disarm.
Unless
specified, all other operations require pressing the “OFF” key
. This is a
SIA CP
-01
requirement.
If an invalid code is entered to silence an alarm condition, the keypad stops beeping for 10
-
15 seconds. If a valid code is not entered during the 10
-15 seconds, the keypad resumes
beeping.
Memory of Alarm
Th
e keypad displays the zone number and type of alarm for any zone that has an alarm condition.
These messages will remain displayed until cleared by a user. If an alarm has occurred, note the zone
number displayed on the keypad and repeat step 1 above to cl
ear the "Memory of Alarm" and restore
the Ready message display. If the Ready message does
not display, go to the displayed zone and
remedy the fault (close windows, etc.). If the fault cannot be remedied, notify the alarm agency.
If the system was armed when the alarm occurred, repeat step 1 twice: once to disarm the system, a
second time to clear the display.
37
Section 19:
Using
the
Keyswitch
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
General
Your system may be
equipped with a keyswitch
for use when arming and disarming a partition. A red
and green light on the keyswitch plate indicate the status of your system as follows:
Green Light
:
Lights when the system is
disarmed and ready
to be armed (no open
zones). If the system is disarmed and the green light is off, it indicates
the
system is not ready (one or more zones are open).
Red Light:
Lights when system is armed or memory of alarm exists.
Messages
Lit Steady:
Partition is
armed in AWAY
mode.
Slow Flashing:
Partition is
armed in STAY
mode.
Rapid Flashing:
Memory of alarm, indicating an alarm has occurred.
Arming
Arming
AWAY
:
Turn the key to the right for 1 second and release. Keypads will beep
twice and the red light will stay on steady.
Arming
STAY
:
Turn the key to the right and hold for longer than 10 seconds, then
release. Keypads will beep three times and the red light will flash slowly.
Disarming
Turn the key to the right and release. If an alarm
has occurred, the red light will be flashing rapidly
(memory of alarm).
38
Section 20:
Chime Mode
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Using the
9
Key
Your system can be set to alert you when a perimeter zone, such as a door
or window, is opened
while it
is disarmed by using CHIME
mode. When activated, three tones will sound at the Keypad whenever a
protected perimeter door or window is opened
, and the Not Ready message will be displayed.
Pressing the
∗
READY
key will display the open protection points.
NOTE
Chime mode can be activated only when the system is disarmed.
Enabling the Chime
Press your
User Code +
9
CHIME
CHIME MODE ON
The C
HIME MODE
ON message will appear for about 2
seconds then disappear. To display this message again (to
determine whether chime mode is on or off), simply press
and hold down the
CHIME key
for 5 seconds.
Disabling the Chime
Press your
User Code +
9
CHIME
CHIME MODE OFF
The C
HIME MODE
OFF message will appear for about 2
seconds then disappears. To display this message again (to
determine whether chime mode is on or off), simply press
and hold down the
CHIME key
for 5 seconds.
39
Section 21:
Viewing Alarm Company
Messages
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
General Information
Users of the system may periodically receive messages
on their display screens from their monitoring
agency or installer. When a message is waiting to be viewed, the message shown below will appear.
MESSAGE. PRESS
0
FOR 5 SECS.
1.
Press and hold down
0
key for 5 seconds.
2.
The message could take up to four screens to display all the information available.
NOTE:
Any message sent by the central station downloader may be viewed at any
partition’s keypad.
40
Section 22:
Panic Keys
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
(Manually Activat
ion
Silent
and/o
r Audible Alarms)
Using Panic Keys
Your system may have been programmed to use special key combinations to manually activate panic
functions. The functions that might be programmed are Silent Emergency
, Audible Emergency
,
Personal Emergency
, and Fire. See your installer for the function(s) that may have been programmed
for your system.
Activate Panic Functions
(Your installer should note which function(s) is active in your system.)
Keys
Zone
Function
1 and *
995
3 and #
996
* and #
999
A
995
B
999
C
996
To use a paired key panic function, simply press both keys of the assigned pair at the same time.
If your keypad(s) have lettered keys for panic functions, press the designated key and hold down for at
least 2 seconds to activate the panic function.
SIA Installations:
Lettered keys not for use in CP
-01 installations.
Silent
Emergency
Sends a silent alarm signal to the central station, but there wi
ll be no audible alarms or visual displays.
Audible E
mergency
Sends
an emergency message to the central station (if connected) and will sound a loud, steady alarm
at your keypad
and
at any external sounders that may be connected (
ALARM
plus a zone number
would also be displayed).
A personal emergency alarm sends an emergency message to the central station
(if connected) and
will sound at Keypads, but not at external bells or sirens
. (
ALARM
plus a zone number would also be
displayed.)
Fire A
larm
Sends a fire alarm message to the central station and will uniquely sound external bells and sirens
(
FIRE
plus a zone number would also be displayed).
41
Section 23:
Speed Key (Macros)
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
General
Information
The “A”,
“B”, “C” and/or “D” keys can be used to activate a string of commands up to 32 keystrokes
each. These commands are known as a macro
and are stored in the system’s memory. Typical Speed
Key
functions in
clude:
•
Arming sequences that involve first bypass
ing certain zones before arming
•
Seldo
m used but repeatable sequences
•
Relay activation sequences
NOTE:
If a speedkey function includes an arming sequence and the user executing it has global
arming, all partitions the user can global arm will arm.
Defining
a Macro
To program a macro, enter your
User
Code +
#
+ [D]
. The following appears:
ENTER SPEED KEY #
01-
32 00=QUIT 01
1.
Enter the desired 2
-digit Speed Key number (01
-32) and press [
∗
].
2.
Enter up to 32 keystrokes. A Speed Key sequence can include different commands. Press
the "D" key to separate different commands
For example, you may want to perform the following sequence:
GOTO partition 2
.......................Enter
∗
2
Bypass zones 10 & 11
............Press
bypass [6], then the zone numbers 010 & 011
Arm in maximum mode
.........Press maximum [4] key
Return to partition 1
...............
Enter
∗
1
3.
Program the Speed Key sequence (using the
example above):
NOTE
:
The
"D"
key is pressed
after each command.
Doing so ends the command and
starts a
new one where control automatically
reenters the user code for you.
4.
Press
"D" twice
to complete the entry and exit.
NOTE
:
When defining Speed Key sequences, do not use the
#
key to represent Quick Arming. The
system uses the code entered in response to the prompt to initiate commands in a Speed Key
sequence, so the quick arm key is unnecessary. The system interprets the use of the
#
key
in a Speed Key sequence
as its designated function
only.
42
Speed Key (Macros) (cont’d)
Executing
To execute a Speed Key sequence, do the following:
•
If a lettered key, A
-B-C has been assigned as a Speed Key, press and hold down the appropriate
key (about 2 seconds).
•
If a user code is required for any part of the Speed Key sequence, the following prompt appears.
Otherwise, the Speed Key sequence autom
atically begins.
Automatic Macros
1.
Press and hold the desired speed key (“A”, “B”, or “C”).
NOTE:
The “D” speed key does not support automatic macros, the macro must be
manually chosen (See below).
2.
If a user code is required for any part of the speed key sequence, the following prompt
appears. Otherwise, the Speed Key sequence automatically begins.
Enter your user code.
ENTER USER CODE
∗∗∗∗
Manual Macros
To manually activate a macro
NOT
assigned to the “A”, “B”, or “C”
keys:
1.
Press and hold down the [D] key for 2 seconds until the following prompt appears:
2.
Press and hold the “D” speed key for two seconds.
3.
The following screen appears:
ENTER MACRO#
01-
32
00 = Quit
4.
Select the desired macro number and press [
∗
].
5.
Enter your user
code.
The selected speed key sequence begins.
43
Section 24:
Access Door Control
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
General Information
Your system may be set up such that a locked access door
(such as in a lobby
) can be unlocked
momentarily or for a specific period of time, using a keypad command. Ask your installer if this has
been done in our system.
Executing
There are several entries that can be entered at the keypad to activate this command:
1.
Enter your security code + [0].
The door will unlock for 2 seconds.
2.
Enter your security code +
#
+ 73, or security code +
#
+ 74 + access point.
The door will unlock for a specific period of time.
3.
Enter your security code
#
+ 75 + access point + function.
4.
The functions available are available.
Grant
..............
will temporarily unlock a door to allow an access.
Protect
..........
will cause a door to unlock only when a valid access is received.
Bypass
..........
will cause a door to be permanently unlocked to allow continuous access.
5.
Access control functions may also be executed use your security code +
#
+ 77. See
Using
#77
Instant Activation Mode
later in this manual.
44
Section 25:
Using #70 Relay Menu Mode
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
General Information
Your system may be set up so that certain lights or other devices can be turned on or off by using the
#70
command
from
a keypad
. Ask your installer if this has been done in your system.
To activate relays from a keypad
Follow the keypad prompts described below.
1.
Enter 4
-digit
Security Code +
#
+70
and enter the desired output.
NOTE:
If the screen below is display, then
the output is not programmed or
the wrong output was selected.
2.
Enter Device #
00=Quit
01
Press the [
∗
] key.
Enter Device #
NOT IN SYSTEM 01
3.
The keypad displays the current status of the device.
01 DEVICE IS OFF
HIT 0 = OFF, 1 = ON 0
4.
Follow the instructions on the keypad.
01 DEVICE IS ON
HIT THE ‘
∗
’ KEY
5.
The keypad returns to the device entry screen
ENTER DEVICE #
ZONE 601
01
45
Section 26:
Using Schedules
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Delaying the Closing Time
Your sys
tem's programmed schedules
may automatically arm the system at a predetermined time. In
the event a user must stay on the premises later than usual, users with master or manager authority
levels can manually delay the automatic arming (closing) time up to 2 hours.
To delay the clo
sing time
1.
Enter your security code (master or
manager authority levels only)
+
#
+ 82
.
2.
A menu prompt will be displayed, asking for the number of hours of delay.
CLOSING DELAY?
KEY 0
-2 HOURS
Enter the desired number
of hours of delay, 1 or 2. The system automatically exits this mode
after entry.
NOTE:
The delay is from the scheduled closing time, not from the time the command is
entered.
IMPORTANT:
The selected delay cannot be
reduced
once it is set. A 1 hour delay
can
be
increased
to 2 hours, though.
3.
The system will automatically send a message to the central station informing them that the
programmed schedule has been changed.
46
Using Schedules (cont’d)
Temporary Open/Close
Schedules
Temporary schedules
allow you to override the normal schedules programmed by the installer.
Temporary schedules can be in effect for up to one week, and take effect as soon as they are
programmed.
They are comprised of an arming (closing) time window
and
a disarming (opening) time window. A
time window is simply a defined period of time, at the end of which arming or disarming will occur.
Before programming, use a worksheet similar to the one below to plan your schedule. This will make it
easier when actually programming the schedule.
Time Windows
1
2
3
4
5
6
7
8
Disarm Window
Start Time HH:MM
Stop Time HH:MM
Arm Window
Start Time HH:MM
Stop Time HH:MM
47
Using Schedules (cont’d)
Programming
Temporary Schedules
Temporary schedules
only affect the partition from which it is entered. Temporary schedules can be
reused at later dates simply by scrolling (by pressing #) to the DAYS? prompt (described below) and
activating the appropriate days. This should be considered when defining dai
ly time windows.
NOTE:
Only users with authority level of manager or higher can program temporary
schedules.
1.
Enter your security code (master or manager authority levels only).
2.
Press the
#
key, followed by
81
.
3.
The following prompts
appear:
MON DISARM WIND.
07:45AM 08:45AM
MON ARM WIND.
07:45AM 08:45AM
1.
Enter the desired hour for Monday’s time window.
2.
Press
∗
to move to min
utes and enter the desired valu
e.
3.
Press
∗
to move to AM/PM. The indication is changed by hitting any key (0
-9)
while the cursor is under the letter A/P position.
NOTE:
Repeat for the stop time entry.
4.
Press the
∗
key to move to the arming window for Monday.
NOTE:
Press
#
to move to the next
screen display without making changes.
After the windows for that day have been completed, the system will prompt for
disarm and arm time windows for the next day. Repeat the procedure for all days of
the week (Monday through Sunday).
When all of the days have been completed, the system will ask which days are to be
activated.
DAYS? MTWTFSS
HIT 0
- 7
X
X
This is the prompt that triggers (activates) the
temporary schedule, and allows the temporary schedule
to be customized to a particular week's needs.
•
To select the days which are to be activated, enter the desired number 1
-
7
(Monday = 1). An "X" will appear under that day, indicating the previously
entered schedule for that day is active.
•
Entering a day's number again will deactivate that day. Pressing 0 will turn all
days on/off.
The temporary schedule will only be in effect for the days which have the letter x
underneath them. As the week progresses, the days are reset to the inactive state.
When completed,
press * to exit
the temporary schedule entry mode.
48
Section 27:
Programming Device Timers
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
General Information
Device timers
consist of an ON time & an OFF time, along with selected days of t
he week in which they
are active.
•
There are up to 20 usable
timers that can be used to control relay outputs
.
•
Your installer will have programmed the appropriate devices into the system (up to 96 devices).
•
Each timer controls a single device (designated as an output number) that you select.
•
For example, timer 1 might be set to turn the porch lights on at 7:00pm and turn them off at
11:00pm.
•
Timer 2 might turn on the air conditioner Monday
-Friday at 4:30pm to cool the premises before
you arrive at 5:00pm, and turn it off at 10:00pm when you are retiring for the night.
•
If desired, different timers can control the same device.
•
For example, timer 2 could be used Monday
-Friday as in the previous example, and t
imer 3
could be set to turn the air conditioner on and off at different times Saturday and Sunday.
To enter the device timer menu mode:
Enter your
Security C
ode
+ #
+ 83.
OUTPUT TIMER
# ?
01-
20,00=QUIT 01
Up to 20 timers can be programmed. Each timer is identified by a
number 1
-20. Enter the desired timer number to be programmed
(1
-20).
Press
∗
to accept entry.
06 07:00P 11:45P
PORCH LITE 04
NOTE:
See your installer for
device numbers.
If that timer number has already been programmed, a summary
screen will appear.
In this example:
06
=
04
=
PORCH LITE
=
07:00PM
=
11:45PM
=
Timer #
Output Device # affected by this
timer
Output Descriptor for Device 4
Start Time;
Stop Time
Press
[
∗
] to continue.
00 ENTER OUTPUT#
00
Enter the desired output device number (1
-96). As the number is
entered, the device's description will appear.
To delete a previously programmed timer, enter 00 as the output
number.
49
Programming Device Timers
(cont’d)
00 ON TIME ?
00:00 PM
1.
Enter the time you want the device turned ON
using 00:01 -
11:59 format.
2.
Press the [
∗
] key to move to the AM/PM field. Press any key 0
-9 to
change the AM/PM indication.
NOTE:
Enter 00:00 if this timer is not being used (
no ON time
is required
).
00 OFF TIME ?
00:00 PM
1.
Enter the time you want the device turned OFF using 00:01 -
11:59 format.
2.
Press the [
∗
] key to move to the AM/PM field. Press any key 0
-9 to
change the AM/PM indication.
NOTE:
Enter 00:00 if this timer is not being used (no OFF time is
required).
00 DAYS? MTWTFSS
HIT 0
-7 X X
1.
Select the days on which the device is to be activated by entering
1-7 (Monday = 1).
2.
An "X" will appear under that day, indicating the output for that
day is active.
3.
Entering a day's number again will deactivate that day. Pressing 0
will turn all days on/off.
The outputs will only be in effect for the days that have the letter x
underneath them. As the week progresses, the days are reset to the
inactive state, unless the permanent option is selected (next screen
prompt). When completed, press [
∗
] to continue.
00 PERMANENT ?
0 = NO, 1 = YES 0
Answering 1 (YES) means the system executes this timer
continuously.
Answering 0 (NO)
means the system executes each day's output only
once.
50
Programming Device Timers (cont’d)
Randomize Output Device Times
Devices in
your system may be set for a random schedule, whereby they will turn on and off at different
times each day. This is useful when going on vacation
(residential) or closing for a holiday
(commericial)
and you desire the turning on and off of the lights to t
he give the appearance of
someone being home. Your installer sets these devices for a random schedule. You can initiate a
random schedule by either of the following methods:
1.
Enter your
Security C
ode
+
#
+ 41.
This will randomize, up to 30
minutes, the activation time of all devices, programmed for
randomization, assigned to the partition the sequence is entered in. Enter the sequence
again to turn off the random schedule.
2.
Enter your
Security Code +
#
+ 42.
This is the same as the method above, except the randomization occurs only on devices
with activation times within 6 PM and 5 AM. Enter the same sequence again to turn off the
random schedule.
51
Section 28:
Using #77 Instant Activation
Mode
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
The #77 Instant Activation Mode is used to activate outputs, bypass zones, etc. immediately upon
exiting the #77 Mode. The actions that may be activated are relay commands, arm/disarm
commands, zone bypassing commands,
and open/close access conditions.
Relay Commands
Action Code
Action Specifier
01
Relay On
Relay #
02
Relay Off
Relay #
03
Relay Close for 2 seconds
Relay #
04
Relay Close XX minutes
∗
Relay #
05
Relay Close YY seconds
∗
Relay #
06
Relay Group On
Relay Group #
07
Relay Group Off
Relay Group #
08
Relay Group Close for 2 seconds
Relay Group #
09
Relay Group Close XX minutes
∗
Relay Group #
10
Relay Group Clos
e YY seconds
∗
Relay Group #
∗
Check with your installer for the amount of time.
Arm/Disarm Commands
Activation times 1 (Beginning), 2 (End), 3 (During) are the only valid choices for automatic arming and
disarming functions.
"During" can be used to arm or disarm the control for a specific time only. For example, if "during" is
selected with Arm
-STAY, the system will automatically Arm-
STAY at the beginning of the window and
automatically disarm at the end of the window.
Action
Code
Action Specifier
20
Arm
-STAY
Partition(s)
21
Arm AWAY
Partition(s)
22
Disarm
Partition(s)
23
Force Arm STAY (Auto-
bypass faulted zns)
Partition(s)
24
Force Arm AWAY (Auto-
bypass faulted zns)
Partition(s)
25
Arm INSTANT
Partition(s)
26
Arm MAXIM
UM
Partition(s)
52
Using #77 Instant Activation Mode (cont’d)
Bypass Commands
Activation times
1 (Beginning)
,
2 (End)
,
3 (During)
are the only valid choices for bypass commands. If
3 (During)
is selected for auto-
bypassing, the system bypasses the zone(s) specified on a particular
zone list at the beginning of the window and unbypasses them at the end of the window. If it is
selected for auto unbypassing, the system removes the bypass at the beginning of the window and
restores the bypass at the end of the window.
Action Code
Action Specifier
30
Auto bypass -
Zone list
Zone list #
31
Auto unbypass -
Zone list
Zone list #
Open/Close Windows
Activation time
3
(Durin
g) is the only valid choice for these commands.
Action Code
Action Specifier
40
Enable Opening Window by partition
Partition(s)
41
Enable Closing Window by partition
Partition(s)
42
Enable Access Window for access group
Access Group
Access Control Commands
Action Code
Action Specifier
55
Access Point Grant
Access Point #
56
Access Point Grant with Override
Access Point #
57
Access Point Protect
Access Point #
58
Access Point Bypass
Access Point #
59
Access Point Lock
Access Point #
60
Access Point Exit
Access Point #
61
Access Point Group Grant
Group #
62
Access Point Group Grant with Override
Group #
63
Access Point Group Protect
Group #
64
Access Point Group Bypass
Group #
66
Access Point Group Exit
Group #
67
Access
Point Partition Grant
Partition #
68
Access Point Partition Grant with Override
Partition #
69
Access Point Protect by Partition
Partition #
70
Access Point Bypass by Partition
Partition #
71
Access Point Lock by Partition
Partition #
72
Access Point Exit
by Partition
Partition #
73
Access Point Trigger On
Trigger #
74
Access Point Trigger Off
Trigger #
53
Using #77 Instant Activation Mode (cont’d)
Additional Commands
Action Code
Action Specifier
77
Access Point Group Enable
Group #
78
Access Point Group Disable
Group #
To enter the Instant Activation Mode:
Enter your
Sec
urity
Code
+ #
+ 77.
ACTION ?
1.
Enter the code for the desired action
The action codes are the events that are to take place
when either the system exits the #77 Mode or the
scheduled time is reached, depending on the action
selected.
2.
Press [
∗
] to continue.
3.
Enter the action specifier
This defines what the action will affect
(relay, relay
group, partition, zone list, user group). The action
specifier screen prompt varies, depending on the type
of action selected.
As an example, if you selected “Auto Bypass”
(Action
30)
as the action, the action specifier prompt would
be:
ZONE
LIST ?
ARE YOU SURE ?
1 = YES 0 = NO
0
Enter
1
(YES) or
0
(NO).
Press [
∗
] to continue.
QUIT MENU MODE?
1 = YES
0 = NO
0
Enter
1
(YES) or
0
(NO).
Press [
∗
] to continue.
54
Section 29:
Event Log Procedures
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
General Information
The system has the ability to record various events in a history log wherein each event is recorded in
one of five categories (listed below), with the time and date of its occurrence.
•
Logs
up to 1000 events with the oldest
event being replaced by the logging of any new event
after the log is full.
•
Using an alpha keypad, the Event Log can be viewed one category at a time, or can display all
events, regardless of category
(ALL EVENT LOG)
.
•
The system also allows selection of completed log
, or only those events occurring since the last
installer service
(RECENT)
.
•
Events in the other partitions can be viewed by users author
ized to access those partitions
NOTE:
Events are displayed in chronolo
gical order, from
most recent to oldest
.
To Display
t he Event Log
1.
Enter your Security Code +
#
+ 6 + 0
NOTE:
The entered secured code has to be a master or manager authority level.
2.
Select the display mode and press
the desired option
ENTER 0 = RECENT
1 = COMPLETE DUMP
RECENT
..............
Displays only those events
occurring since last Event Log Clear
command was executed.
COMPLETE
.......
Displays complete event log (up to
1000 events)
3.
Select the partition, 0
-
8
SCAN LOG BY PART
0 = NO 1
-8 =
PARTITION #
Enter the partition number for the partition whose
events are to be displayed.
NOTE:
Entering 0 (NO) displays all partitions'
events.
55
Event Log Procedures (cont’d)
4.
Scroll through the categories.
Use the [3] & [1] keys
(for next and previous categories respec
tively) to display
the
categories of events.
Press [8] to select a catego
ry
and display the first event. Press [8] again for each
subsequent event.
Example:
Shows burglary alarm occurred i
n zone 3 (C003) of partition 1 (P1),
at 12:02AM
on January 1.
P1 01/01 12:02AM
BURGLARY C003
Typical Event Log Display
After the last event
has been displayed, the END OF EVENT LOG message appears for a
few seconds, then the system automatically displays the RECENT/COMPLETE mode select
screen again (see step 2).
5.
To EXIT the Event Log Press [
∗
] at any time.
ALARM EVENT LOG
TYPE CCC UUU
ALARM EVENT LOG
Displays time and date for zones that has either caused an alarm or has been restored in the
selected partition.
CHECK EVENT LOG
Displays time and date for zones that has caused a trouble or supervisory condition in the
selected parti
tion.
BYPASS EVENT LOG
Displays time and date for zones that has been bypassed in the partition.
OPEN EVENT LOG
Displays time, date and user number or 6
-character descriptor for the user, if programmed,
for each arming and disarming of the system for the partition selected.
SYSTEM EVENT LOG
Displays time and date for system problems, such as AC Loss, low battery, etc., regardless of
partition.
ALL EVENT LOG
Displays all categories of events in chronological order.
6.
See your Installer for additional info
rmation concerning the event log.
56
Section 30:
Setting the Time and Date
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
1.
Enter
Installer or Master Code +
#
+ 63
. Typical display shows:
TIME/DATE
THU
12:01AM 12/17/2016
•
The day of the week is automatically calculated
based on the date entered.
•
Time and date entries are made by simply entering
the appropriate hour, minute, month, day and year.
Press [
∗
] to move the cursor to the right of the display, to
the next position.
Press [#] to move the cursor to the left of the display, to
the previous position.
2.
Enter the hour. Then press [
∗
] to move to the “minutes” field.
3.
Enter the minutes. Press [
∗
] to move to the AM/PM position.
4.
Press any key 0
-9 to change
AM to PM, or PM to AM. Press [
∗
] to move cursor to the “month”
field position.
5.
Enter the month using a 2
-digit entry. Press [
∗
] to move cursor to the “day” field position.
6.
Enter the day using a 2
-digit entry. Press [
∗
] to move cursor to the “year” field position.
7.
Press [
∗
] to exit the real
-time clock edit mode.
57
Section 31:
Testing
the
System
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
(To Be Conducted Weekly)
Using the
5
TEST Key
The
TEST
key
puts your system into Test mode
, which allows each protection point to be checked for
proper operation.
1.
Disarm the system and close all protected windows, doors, etc. READY should be displayed.
2.
Enter your security code and press the
5
TEST
key.
3.
The external sounder should sound for 3 seconds and then turn off. If the sounder does not
sound, it may be due to dialer communica
tion activity.
Wait a few minutes and try again. If the sounder still does not sound,
CALL FOR SERVICE
IMMEDIATELY
.
NOTE:
This command will cause the panel to look for the battery and if seen, activates
the alarm output (siren) for 3 seconds, and will clear a low battery if it is a
successful test.
The Keypad Displays:
BURG WALK TEST
IN PROGRESS
•
The test includes all Fire, Burglary and Panic zones.
•
Each time a protection zone is faulted (opened), the keypad should beep three
times. If the sounder does not sound,
CALL FOR SERVICE IMMEDIATELY
.
•
In the case of wireless transmitters, sensitivity of the wireless receiver will be reduced
by 50% for the
Go/No Go
test.
NOT
E:
If two wireless receiver
s exist, the system beep
s 1 time for receiver # 1,
2 times for receiver # 2, and 3 times if both receivers received the
signal.)
•
The keypad displays the zone number and alpha descriptor while a door or window
remains open or while a detector remains activated.
58
Testing the System (cont’d)
To end this test, enter any security code and press OFF.
•
The system automatically exits the Test mode if there is no activity (no doors or
windows are opened and closed, no motion detectors are activated, etc.) for 30
minutes.
•
The system beeps the keypad(s) twice every 5 seconds during the last 5 minutes as a
warning that it is about to exit the Test mode and return to normal operation.
All zone types will cause keypad to beep
NOTES
1.
When panel is in Test mode wireless keys will not arm or disarm system. When
a
button is pressed it shows
a fault of the zone assigned to
the
wireless key.
Because
the wireless key does not send a zone restore (unlike opening a door, then closing it
(which is the restore)),
because the wireless key does not send a zone restore.
Note
the fault does not clear until
exiting
Test mode.
2.
If the sounder does not sound, this may be an indication that the backup battery is
discharged or missing, and should be showing a low battery on the keypad.
3.
Test mode is active only for the partition at which Test mode is enter
ed. Other
partitions are still operative and will cause the external sounder and communicator to
activate if an alarm condition occurs.
4.
Panel will go into test mode if zones are faulted,
but does not go into test mode if
zones are bypassed or in trouble.
Testing Your System
1.
Open and close each protected door and window in turn and listen for three beeps. Each
faulted protection point should appear on the display.
2.
Walk in front of any motion detectors (if used) and listen for three beeps as movement is
detected (wireless motion detectors have a 3
-1/2 minute lockout between trips). Each
detector’s should appear on the display when it is activated.
3.
Follow the manufacturer's instructions to test all smoke detectors
to
ensure that all are
functioning properly. Each detector should appear on the display when activated.
4.
When all protection points have been checked, there should be no zone identification
numbers displayed. If a problem is experienced with any protection point (no confirming
sounds, no display),
CALL FOR SERVICE IMMEDIATELY
.
5.
Turn off Test mode by enteri
ng the security code + the
OFF
key.
59
Section 32:
Fire Alarm System
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
General
Your fire alarm
system (if installed) is on 24 hours a day, providing continuous protection. In the event
of an emergency, the smoke and heat detectors automatically send signals to your Control, triggering
a loud interrupting sound from the keypad and the optional exterior sounders. FIRE appears at your
keypad and remains on until you silence the alarm.
NOTE
S
•
All smoke detectors must be tested monthly by pressing the
TEST
button located on the
detector. Be aware that your keypad(s) and local siren(s) will activate (ent
er your
4
-digit code +
[Off]
to silence).
Important!
If your system is monitored by a central station you must first call the central station to advise
them that a test is in progress.
•
If the TEST button does not cause the detector to activate it must be
replaced immediately.
•
Ask your installer if your system is programmed for fire alarm verification, which can help reduce
false alarms from smoke detectors.
In Case o
f Fire Alarm
Should you become aware of a fire emergency before your detectors sense the p
roblem, go to your
nearest keypad and manually initiate an alarm by pressing the panic key assigned as FIRE emergency
(if programmed by the installer) and hold down for at least 2 seconds.
Important!
Evacuate all occupants from the premises.
If flames and/or smoke are present, leave the premises and notify your local Fire Department
immediately.
If no flames or smoke are apparent, investigate the cause of the alarm. The descriptor of the zone(s) in
alarm appears at the keypad.
Silencing
a Fire Alarm
Silence the alarm by entering your code and pressing
OFF
. To clear the display, enter your code and
press the
OFF
key again.
If the keypad does not indicate a READY condition after the second OFF sequence, press the
READY
key
to display the faulted
zone(s). Be sure to check that smoke detectors are not responding to smoke
or heat producing objects in their vicinity. Should this be the case, eliminate the source of heat or
smoke.
If this does not remedy the problem, there m
ay still be smoke in the detector. Clear it by fanning the
detector for about 30 seconds.
You can clear the display by entering your
Security
Code + the OFF
.
60
Section 33:
Trouble Conditions
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Typical Trouble Displays
The word
CHECK
or
TRBL
on the Keypad's display, accompanied by a rapid "beeping" at the Keypad,
indicates that there is a trouble condition
in the system.
To silence the beeping
sound
for trouble conditions, press any key.
•
A display of
“CHECK”
or
“TRBL”
accompanied by a display of
“
CALL SERVICE
”
indicates that a
problem exists with the system that eliminates some of the protection.
CALL FOR SERVICE
IMMEDIATE
LY
.
•
A display of
“CHECK”
or
“TRBL
"
accompanied by one or more zone descriptors indicates that a
problem exists with those zone(s)
∗
. First, determine if the zone(s) displayed are intact and make
them so if they are not. If the problem has been corrected, the display of the zone descriptor(s)
and
“CHECK”
or
“TRBL”
should disappear. If not, key an OFF sequence (
Security Code + Off
)
to c
lear the display. If the display persists,
CALL FOR SERVICE IMMEDIATELY
.
•
A display of
“
CHECK
”
or
“
TRBL
”
accompanied by a numeric display of “6XX,” where XX = 01
-32,
indicates a trouble on a supervised relay (corresponding relay number 01
-32).
•
A display of
“
CHECK
”
or
“
TRBL
”
accompanied by a numeric display of “8XX,” where XX = 00
-30,
indicates a trouble on a peripheral device (connected to the panel’s keypad terminals) of a
corresponding device address (00
-30).
•
A display of
“
CHECK
”
or
“
TRBL
”
accompanied by a
numeric display of “9XX,” where XX = 00
-99,
indicates a system trouble exists (
RF Receivers, Bell output,
etc.). These zones are as follows:
970
.............
Bell Supervision
988
.............
2
nd
RF Receiver –
not receiving signals
990
.............
1
st
RF Receiver –
not receiving signals
997
.............
Polling Loop Short
•
A display of
"
COMM. FAILURE
"
at the Keypad indicates that a failure has occurred in the
communication portion of your system.
CALL FOR SERVICE IMMEDIATELY.
•
A display of
"Phone Line Cut"
accompanied by rapid beeping at the Keypad indicates that a
failure has occurred in the telephone line.
CALL FOR SERVICE IMMEDIATELY
.
•
A display of
"SYSTEM LO BAT
"
, accompanied by a once per minute "beeping" at the Keypad
indicates that a low system battery condition exists.
CALL FOR SERVICE IMMEDIATELY
.
•
A display of
"LO BAT
"
and a zone descriptor, accompanied by a once per minute "beeping" at
the Keypad indicates that a low battery condition exists in the wireless trans
mitter displayed.
CALL FOR SERVICE IMMEDIATELY.
•
A display of
"MODEM COMM
"
indicates that the control is on-
line with the central station's
remote computer. The control will not operate while on-
line.
61
Trouble Conditions (cont’d)
Power
Failure
If the
POWER
indicator is off, operating power for the system has stopped and is inoperative.
CALL
FOR SERVICE IMMEDIATELY.
If the
POWER
indicator is on, but the message
"AC LOSS
"
is displayed, the Keypad is operating
on
battery power only. If only some lights are out on the premises, check circuit breakers and fuses and
reset or replace as necessary.
CALL FOR SERVICE IMM
EDIATELY
if AC power cannot be restored.
SERVICING INFORMATION
Your local Honeywell dealer
is the person best qualified to service your alarm system.
Arranging some kind of regular service program with him is advisable.
Your local Honeywell
dealer
:
Name:
Address:
Phone:
62
Section 34:
Recommendations
for
Proper
Protection
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
The following recommendations for the location of fire and burglary detection devices help provide
proper coverage for the protected premises.
Recommendations
for
Smoke
and
Heat Detectors
With regard to the number and placement of smoke/heat detectors, we subscribe to the
recommendations contained in the National Fire Protection Association's (NFPA
) Standard #72 noted
below.
Early warning fire detection is best achieved by the installation of fire detection
equipment in all rooms
and areas of the household as follows: For minimum protection a smoke detector should be installed
outside of each separate sleeping area, and on each additional floor of a multi
-floor family living unit,
including basements. The installation of smoke detectors
in kitchens, attics (finished or unfinished), or
in garages is not normally recommended.
For additional protection the NFPA recommends that you install
heat
or
smoke detectors
in the living
room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms,
basements and attached garages.
63
Recommendations
for
Proper Protection (cont’d)
In addition, we recommend the following:
•
Install a smoke detector inside every bedroom where a smoker sleeps.
•
Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters,
air conditioners or humidifiers) are used.
•
Install a smoke detector inside every bedroom where someone sleeps with the door partly or
completely closed.
Smoke could be blocked by the closed door. Also, an alarm in the hallway
outside may not wake up the sleeper if the door is closed.
•
Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters)
long.
•
Install smoke detectors in any room where an alarm control is located, or in any room where
alarm control connections to an AC source or phone lines are made. If detectors are not so
located, a fire within the room could prevent the control from reporting a fire or an intrusion.
64
Section 35:
Emergency Evacuation
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Establish and regularly practice a plan of escape in the event of fire. The following steps are
recommended by the National Fire Protection Association:
1.
Position your detector or your interior and/or exterior sounders so that they can be heard
by all occupants.
2.
Determine two means of escape from each room. One path of escape should lead to the
door that permits normal exit from the building. The other may be a window, should your
path b
e impassable. Station an escape ladder at such windows if there is a long drop to the
ground.
3.
Sketch a floor plan of the building. Show windows, doors, stairs and rooftops that can be
used to escape. Indicate escape routes for each room. Keep these routes free from
obstruction and post copies of the escape routes in every room.
4.
Assure that all bedroom doors are shut while you are asleep. This will prevent deadly smoke
from entering while you escape.
5.
Try the door. If the door is hot, check your alternate esc
ape route. If the door is cool, open it
cautiously. Be prepared to slam the door if smoke or heat rushes in.
6.
Where smoke is present, crawl on the ground; do not walk upright. Smoke rises and may
overcome you. Clearer air is near the floor.
7.
Escape quickly; don't panic.
8.
Establish a common meeting place outdoors, away from your house, where everyone can
meet and then take steps to contact the authorities and ac
count for those missing. Choose
someone to assure that nobody returns to the house —
many die going
back.
65
Section 36:
Maintaining Your System
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Taking Care of Your System
The components of your security system are designed to be as free of maintenance as possible.
However, there are some things
you can do to make sure that your system is in reliable working
condition.
1.
Test your system weekly.
2.
Test the system after any alarm occurs (see
TESTING THE SYSTEM
).
Replacing Batteries
in Wireless Sensors
Wireless sensors
may n
ot have been
used in your
security system
Each wireless sensor
in your system has a 9
-volt or 3
-volt battery. The
system detects a low battery in any wireless sensor, including smoke
detectors, the optional personal emergency trans
mitter, and the optional
portable wireless key
. (A low battery in a portable wireless keypad is detected
as soon as one of its keys is pressed, and the keypad will display
00
.)
Alkaline batteries
provide a minimum of 1 year of operation, and in most
units and applications, provide 2
–4 years of service. Actual battery life
will
depend on the environment in which the sensor is used, the number of
signals that the transmitter in the sensor has had to send, and the specific
type of sensor. Factors such as humidity, high or low temperatures or large
swings in temperature, may all lead to the reduction of actual battery life in
an installation.
If you have a low battery
in a wireless sensor, a
low battery
message is displayed on the keypad.
In addition, a battery
-operated smoke detector with a low battery also emits a single "chirp" sound
once approximately every 20
-30 seconds, identifying itself as the smoke detector with the weak
battery. If you do not replace a smoke detector's low battery, the smoke detector may sound
continuously, as if there were a fire alarm.
NOT
E:
The low battery message comes on as a warning that battery replacement in indic
ated
sensor(s) is due within 30 days. In the meantime, the sensor(s) causing the low battery
indication is still fully operational.
IMPORTANT
!
Use only batteries recommended by your installer as replacement.
66
Maintaining Your System (cont’d)
Silencing
Low Battery Warning
Tones at the Keypad
The keypad’s warning tones can be silenced by performing an OFF sequence (code plus OFF key)
,
but
the Keypad's low battery message display will remain on as a reminder that you have a low battery
condition in one or more of your sensors. When you replace the weak battery with a fresh one, the
sensor will send a "good battery" signal to the control as soon as the sensor is activated
(opening/closing of door, window, etc.), causing the low ba
ttery display to turn off. If the sensor is not
activated, the display will automatically clear within approximately 1 hour.
Routine Care
•
Treat the components of your security
system as you would any other electrical equipment. Do
not
slam sensor
-protected doors or windows.
•
Keep dust from accumulating on the keypad and all protective sensors, particularly on motion
sensors and smoke detectors.
•
The keypad and sensors should be cleaned carefully with a dry soft cloth.
Do not spray water o
r
any other fluid on the units.
67
Section 37:
Quick Guide
to
System Functions
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Function
Procedure
Comments
Check Zones
Press [
∗
].
To view faulted zones when is system not ready
Display
All
Descriptors
Press and hold [
∗
] for 5 seconds.
Displays all alpha descriptors programmed by
installer.
Arm System
1.
Enter code.
2.
Press arming key desired (AWAY,
STAY, INSTANT, MAXIMUM).
Arms system in mode selected.
NOTE:
After pressing the STAY or
INSTANT arming key, enter 1, 2 or
3 to arm in the desired STAY or
INSTANT mode.
Disarm System
Enter code. Press OFF [1].
Disarms system and silences alarms.
Bypass Zones
1.
Enter code. Press BYPASS [6].
2.
Enter zone numbers to be
bypassed (use 3
-digit entries).
Bypassed zones are unprotected and will not
cause an alarm if violated.
Quick Bypass
1.
Enter code. Press BYPASS [6].
2.
Press [#].
Bypasses all faulted zones automatically.
Group Bypass
1.
Enter code. Press BYPASS [6].
2.
Press
[
∗
]. Enter Group Number
(01-
15)
Bypasses all zones assigned to the group.
Chime Mode
Enter code. Press CHIME [9].
Keypad will sound if doors or windows are
violated while system disarmed.
Test Mode
Enter code. Press TEST [5]
Activates alarm sounder and allows sensors to
be tested.
View Messages
Press and hold [0] for at least 5
seconds.
Message from central station will appear.
View User
Capabilities
Enter user's code. Press [
∗
] + [
∗
].
Displays partitions & authority levels assigned
to the user.
GOTO Partition
1.
Enter security code. Press [
∗
].
2.
Enter partition number (1
-8).
3.
0 returns to default partition.
Allows a user at one keypad to perform
functions in another partition, if that user is
authorized to do so.
Self
-Help
Press and hold any function
key for at
least 5 seconds.
Will display abbreviated instructions for the
key pressed.
Add a User
1.
Enter master/manager code.
2.
Press CODE [8].
3.
Enter new user's user number.
4.
Enter code for that user.
5.
Enter authority for that user in this
partition (1
-5).
6.
Follow prompts, 1=Yes, 0=No.
Master & Manager level users can add users to
the system, each with its own code and
authority level.
68
Quick Guide
to
System Functions (cont’d)
Change a User's
Code
1.
Enter master/manager code.
2.
Press CODE [8].
3.
Enter user's 3
-digit number.
4.
Enter new code for that user.
5.
Press 0 (No) at prompt.
Master & Manager level users can change
their own or other users' codes.
Delete a User
1.
Enter master/manager code.
2.
Press CODE [8].
3.
Enter user no. to be deleted.
4.
Enter
master/manager code.
5.
Press 1 (Yes) at prompt.
Master & Manager level users can delete
users.
A user can only be deleted by a user with
higher authority level.
Real
-Time Clock
Enter Master code. Press
#
+ [63].
Press
[
∗
] or [#] to move cursor. Enter time and
date accordingly. Press any key (0
-9) for
AM/PM.
Control Output
Device
Enter security code. Press
#
Enter 71 or 72.
Activate output device as programmed.
Enter security code. Press
#
Enter 70.
Activate output device manually
Randomize Output
Device
Enter security code. Press
#
Enter 77.
Activate output device or system event
instantly
Enter security code. Press
#
Enter 41
Randomize output devices set for random
schedules
Enter security code. Press
#
Enter 42.
Randomize output devices set for random
schedules with activation times between 6 PM
and 5 AM
Access Control
Enter 0.
Exit multi-
partition multi-
panel mode and
multi
-
panel view mode.
Enter security code. Enter 0.
Activate access relay for current partition.
Enter security code
Press [#]. Enter 73.
Request to enter or exit at a console.
Enter security code
Press [#]. Enter 74.
Enter access point number.
Request to enter or exit at an access point.
Enter security code. Press
#
.
Enter 75. Enter access point number.
Enter state (1
-3)
Change the access point state.
69
Section 38:
Summary
of
Audible
Notification
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
(Alpha Display Keypads)
SOUND
CAUSE
DISPLAY
LOUD,
INTERRUPTED
∗
Keypad & External
FIRE ALARM
FIRE
is displayed; descriptor of zone in alarm is
displayed.
LOUD,
CONTINUOUS
∗
Keypad & External
BURGLARY/AUDIBLE
EMERGENCY ALARM
ALARM
is displayed; descriptor of zone in alarm is
also displayed.
ONE SHORT BEEP
(not repeated)
Keypad only
a.
SYSTEM DISARM
b.
SYSTEM ARMING ATTEMPT
WITH AN OPEN ZONE.
c.
BYPASS VERIFY
a.
DISARMED/READY TO ARM is displayed.
b.
The number and descriptor of the open
protection
zone is displayed.
c.
Numbers and descriptors of the bypassed
protection zones are displayed (One beep is
heard for each zone displayed). Subsequently,
sthe following is displayed:
DISARMED BYPASS
Ready
to Arm
ONE SHORT BEEP
(once every 15
sec.) Keypad only
SYSTEM IS IN TEST MODE
Opened Zone identifications will appear.
TWO SHORT
BEEPS
(once every 5 sec.)
Keypad only
SYSTEM IS ABOUT TO
AUTOMATICALLY EXIT TEST
MODE
Opened Zone identifications will appear.
ONE BEEP
(every 60 sec.)
Keypad only
LOW BATTERY AT A
TRANSMITTER
LO BAT
displayed with description of transmitter.
TWO SHORT
BEEPS
Keypad only
ARM AWAY OR MAXIMUM
ARMED AWAY or ARMED MAXIMUM
is displayed.
Red ARMED indicator is lit.
THREE SHORT
BEEPS
Keypad only
a.
ARM STAY OR INSTANT
b.
ZONE OPENED WHILE
SYSTEM IS IN CHIME
MODE.
c.
ENTRY WARNING
∗∗
a.
ARMED STAY ZONE BYPASSED or ARMED
INSTANT ZONE BYPASSED is displayed. Red
ARMED indicator is lit.
b.
CHIME
displayed, descriptor of open protection
zone will be displayed if the [Q] key is pressed.
c.
DISARM SYSTEM OR ALARM WILL OCCUR is
displayed.
70
Summary of Audible
Notification
(cont’d)
RAPID BEEPING
Keypad only
a.
TROUBLE
b.
AC POWER LOSS
ALERT
∗∗∗
c.
MEMORY OF ALARM
a.
CHECK
displayed. Descriptor of troubled
protection zone is displayed.
b.
AC LOSS
displayed (may alternate with other
displays that may be present).
c.
FIRE
or
ALARM
is displayed; descriptor of zone in
alarm is displayed.
SLOW BEEPING
Keypad only
a.
ENTRY DELAY WARNING**
b.
EXIT DELAY WARNING
(if programmed)
a.
DISARM SYSTEM
OR ALARM WILL OCCUR
is
displayed. Exceeding the delay time without
disarming causes alarm.
b.
ARMED AWAY or ARMED MAXIMUM
is displayed
along with You May Exit Now
∗
If bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady
ring.
∗∗
Entry warning may consist of three short beeps or slow continuous beeping, as programmed by
your installer.
∗∗∗
Loss of system battery power is not indicated or annunciated by the keypad (warnings are for
loss of AC power only).
71
Section 39:
Index
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
#70 Command
..........................................................
44
AC Loss
..........................................................................
61
Access Another Partition
......................................
19
Access Control Commands
.................................
52
Access Door
.................................................................
43
Action Code
.................................................................
51
Action Specifier
........................................................
51
Add a User
....................................................................
15
ADD NEW USER
........................................................
17
Add User Code
............................................................
14
Alarm
..................................................................................
2
Alkaline Batteries
......................................................
65
Alpha Keypads
...............................................................
6
Arm/Disarm Commands
.......................................
51
Armed
................................................................................
4
ARMED INDICATOR
...................................................
9
Audible Emergency
..................................................
40
Audible Signals
..................................................
69, 70
Authority Level
...........................................................
12
Authority Levels
.................................................
13, 14
Auto
-STAY Arming
....................................................
32
Away
............................................................................
4, 20
AWAY
...............................................................................
37
AWAY Mode
.................................................................
34
Battery Life
...................................................................
65
Burglary
............................................................................
1
Burglary Protection
.....................................................
4
Bypass-
Access Door
..............................................
43
Bypass Commands
..................................................
52
Bypassing
.....................................................................
27
Call Service
.................................................................
60
Carbon Monoxide Protection
................................
2
Change a User's Code
............................................
17
Change User Code
....................................................
14
CHECK
...........................................................................
60
Chime
.......................................................................
4, 38
Closing Time
...............................................................
45
Comm. Failure
...........................................................
60
Delaying Closing Time
...........................................
45
Delete a User
..............................................................
18
Delete User Code
......................................................
14
Descriptors
..................................................................
26
Device Timers
........................................................
5, 48
Disarm
...........................................................................
36
DOC
.................................................................................
75
Duress
............................................................................
13
Duress Code
...............................................................
12
Emergency
.....................................................................
1
Entry Delay
..................................................................
11
Entry/Exit
........................................................................
2
Exit Delay
.....................................................................
11
Exit User Edit Mode
................................................
14
Fire
..............................................................................
1, 40
Fire Alarm
.....................................................................
59
Fire Protection
..............................................................
2
GLOBAL ARM
.............................................................
16
Global Arming
............................................................
20
Goto
.........................................................................
16, 19
GOTO Command
.........................................................
5
Graphic/Touch
-Screen Keypad
..............
1, 6, 33
Group Bypass
.............................................................
29
Honeywell Dealer
.....................................................
61
Instant
......................................................................
4,
20
INSTANT
.......................................................................
11
INSTANT Mode
..........................................................
33
Keypad
..............................................................................
1
Keypad Back Lighting
...............................................
6
Keypads
............................................................................
6
Keyswitch
.....................................................................
37
LO Bat
...........................................................................
61
72
Low Battery
..................................................................
65
Low Battery Warning
...............................................
66
Macro
..............................................................................
41
Macros
..............................................................................
4
Manager
........................................................................
13
Master
............................................................................
13
Master Keypad
......................................................
5, 21
Maximum
.................................................................
4, 20
MAXIMUM
....................................................................
11
MAXIMUM Mode
......................................................
35
Memory of Alarm
..................................................
4, 36
Messages
......................................................................
39
Modem Comm
..........................................................
61
MULTI
-ACCESS
.........................................................
16
NFPA
...............................................................................
62
Night
...............................................................................
33
Not Ready
.....................................................................
25
Off
.....................................................................................
20
OFF
..................................................................................
36
Open Zones
.................................................................
25
Open/Close Schedules
..........................................
46
Open/Close Windows
.............................................
52
Operator A
....................................................................
13
Operator B
....................................................................
13
Operator C
....................................................................
13
OUTPUT TIMER
.........................................................
48
Panic Keys
....................................................................
40
PANIC KEYS
....................................................................
9
Partitioned System
.....................................................
2
Personal Emergency
...............................................
40
Power
..............................................................................
61
POWER/READY INDICATOR
..................................
9
Quick Arm
.........................................................................
9
Quick Arming
..............................................................
12
Quick Bypass
..............................................................
28
Quick Exit
......................................................................
35
Quick Guide
.........................................................
67, 68
Randomize Output Devices
................................
50
Ready
..............................................................................
25
Ready
Key
.....................................................................
25
Real
-Time Clock
......................................................
68
Relay Commands
.....................................................
51
Relay Menu Mode
....................................................
44
Replacing
Batteries
.................................................
65
RF BUTTON
.................................................................
15
Routine Care
...............................................................
66
Schedules
...............................................................
4, 45
Security Code
.............................................................
12
Security Codes
...........................................................
12
Sensing Devices
..........................................................
2
Silencing a Fire Alarm
............................................
59
Silent Emergency
.....................................................
40
Smoke Detectors
......................................................
58
Speed Key
...............................................................
4, 41
Stay
.............................................................................
4, 20
STAY
................................................................................
37
System LO Bat
..........................................................
60
Temporary Schedules
.....................................
46, 47
Temporary Users
......................................................
15
Test Key
.........................................................................
57
Test Mode
....................................................................
57
Time Window
..............................................................
46
TRBL
...............................................................................
60
Trouble Condition
....................................................
60
Unable To Arm Lobby
.............................................
23
User Edit Mode
.........................................................
14
User Numbers
............................................................
12
User's Instructions
.....................................................
5
Using #77 Instant Activation Mode
...............
51
Wireless Sensor
.........................................................
65
Zone Bypassed
...................................................
32, 33
Zone Descrip
tors
......................................................
26
Zones
.................................................................................
2
73
FEDERAL COMMUNICATIONS COMMISSION STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation
Instructions or User's Manual.
Unauthorized changes or modifications could void the user's authority to operate
the equipment.
FCC CLASS B STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires
the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict
accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has
been ty
pe tested and found to comply with the limits for a Class B computing device in accordance with the
specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such
interference in a residential installation. However
, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one
or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receive
r away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different
branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES
-003.
Cet appareil numérique de la classe B est conforme à la norme NMB
-003 du Canada.
FCC/IC STATEMENT
This
device complies with Part 15 of the FCC Rules, and Industry Canada’s license-
exempt RSSs.
Operation is
subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must
accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son
fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences
nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les interferences causant une
reception indésirable.
IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS
In the event of telephone operational problems, disconnect the control from the phone line by removing the plug
from the phone wall jack. We recommend that your installer demonstrate this disconnection on installation of the
system. Do not attempt to disconnect the phone connection inside the control. Doing so will result in the loss of
your phone lines. If the regular phones work correctly after the control has been
disconnected from the phone wall
jack, the control has a problem and you should immediately call for service. If upon disconnection of the control,
there is still a problem on the phone line, notify the Telephone Company that they have a problem and request
prompt phone repair service. The user may not under any circumstances attempt any service or repairs to the
security system. Repairs must be made only by authorized service (see the LIMITED WARRANTY statement for
information on how to obtain service).
74
“FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 NOTICE
This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label
that contains, among other information, the FCC registration number and ringer equivalence
number
(REN) for this equipment. If requested, this information must be provided to the telephone company.
This equipment uses the following jacks:
An RJ31X is used to connect this equipment to the telephone network.
The REN is used to determine the quant
ity of devices which may be connected to the telephone line.
Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming
call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be cer
tain of the
number of devices that may be connected to the line, as determined by the total RENs, contact the
telephone company to determine the maximum REN for the calling area.
If this equipment causes harm to the telephone network, the telephone company
will notify you in
advance that temporary discontinuance of service may be required. If advance notice is not practical,
the telephone company will notify the customer as soon as possible. Also, you will be advised of your
right to file a complaint with t
he FCC if you believe necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that
could affect the operation of the equipment. If this happens, the telephone company will provide
advance notice in order fo
r you to make the necessary modifications in order to maintain uninterrupted
service.
If trouble is experienced with this equipment, please contact the manufacturer for repair and warranty
information. If the trouble is causing harm to the telephone networ
k, the telephone company may
request you remove the equipment from the network until the problem is resolved.
There are no user serviceable components in this product, and all necessary repairs must be made by
the manufacturer. Other repair methods may inv
alidate the FCC registration on this product.
This equipment cannot be used on telephone company
-provided coin service. Connection to Party Line
Service is subject to state tariffs.
This equipment is hearing
-aid compatible.
When programming or making test calls to an emergency number, briefly explain to the dispatcher the
reason for the call. Perform such activities in the off-
peak hours; such as early morning or late evening.
75
Ringer Equivalence Number Notice:
The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the
maximum number of terminals allowed to be connected to a telephone interface. The termination on
an interface may consist of any combination of devices subject only to the requirement that the sum of
th
e Ringer Equivalence Numbers of all the devices does not exceed five.
AVIS :
L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le
nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d’une
interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition
que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas cinq.
76
WARNING
!
THE LIMITATIONS OF THIS ALARM
SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or
other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a
variety of reasons. For example:
• Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm
sensor or disconnect an alarm warning device.
• Intrusion detectors (e.g. passive infrared detectors), smoke d
etectors, and many other sensing devices will not work
without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put
in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly.
• Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if
the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the
path.
• A user may not be able to reach a panic or emergency button quickly enough.
• While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not
activate or provid
e early warning for a variety of reasons in as many as 35% of all fires, according to data published by
the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this
System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke
detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs,
or on the other side of closed doors. Smoke detectors also may not sen
se a fire on another level of a residence or
building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors
have sensing limitations. No smoke detector can sense every kind of fire every time. In gen
eral, detectors may not always
warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas,
improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arso
n.
Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as
anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death.
• Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their
installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple
beams of protection, and intrusion can only b
e detected in unobstructed areas covered by those beams. They cannot
detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or
windows. Mechanical tampering, masking, painting or spraying of
any material on the mirrors, windows or any part of
the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however,
as the ambient temperature of protected area approaches the temperature range of 9
0° to 105°F, the detection
performance can decrease.
• Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the
other side of closed or partly open doors. If warning devices sound on a differe
nt level of the residence from the
bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not
hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by
passing traffic.
Finally, alarm warning devices, however loud, may not warn hearing
-impaired people or waken deep sleepers.
• Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service
or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders.
• Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect
themselves from the emergency situation. In
the case of a monitored alarm system, authorities may not respond
appropriately.
• This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to
last as long as 10 years, the electronic components could fail at any time.
The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance.
This alarm system should be tested weekly to make sure all sensors and transmitters are working properly.
Install
ing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for
insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and
continue to insure their lives
and property.
We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved
ones to learn about these developments.
77
TWO YEAR LIMITED WARRANTY
Honeywell International Inc., acting through its Security & Communications business (“Seller”), 2 Corporate Center
Drive, Melville, New York 11747 warrants its products to be free from defects in materials and workmanship under
normal use and service, normal wear and tear excepted, for 24 months from the manufacture date code; provided,
however, that in the event the Buyer presents a proper invoice relating to the purchased product and such invoice
bears a date later than the manufacture date, then Seller may at its discretion, reflect the warranty period as
commencing at invoice date. Except as required by law, this Limited Warranty is only made to Buyer and may not
be transferred to any third party. During the applicable warranty period, Seller will repair or replace, at its sole
option and as the exclusive remedy hereunder, free of charge, any defective products.
Seller shall have no obligation under this Limited Warranty or otherwise if the product:
(i)
is improperly installed, applied or m
aintained;
(ii)
installed outside of stated operating parameters, altered or improperly serviced or repaired by
anyone other than the Seller/Seller’s Authorized Service/Repair Center;
(iii)
damage is caused by outside natural occurrences, such as lightning, power surges, fire, floods,
acts of nature, or the like; or
(iv)
defects result from unauthorized modification, misuse, vandalism, alterations of serial numbers,
other causes unrelated to defective materials or workmanship, or failures related to batteries of
any
type used in connection with the products sold hereunder.
Exceptions to Warranty With Respect to Honeywell Products listed below:
Hardwire Contacts and PIRs –
Seller warrants parts for hardwire contacts and PIRs in accordance with the terms of
the above limited warranty for a period of five (5) years from the manufacture date code.
EXCLUSION OF WARRANTIES, LIMITATION OF LIABILITY
THERE ARE NO WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR
A PARTICULAR P
URPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. TO THE FULLEST EXTENT PERMITTED BY LAW, IN NO CASE SHALL SELLER BE LIABLE TO ANYONE
FOR ANY (i) CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES ARISING OUT OF OR
RELATING IN ANY WAY TO THE PRODUCT AND/OR FOR BREACH OF THIS OR ANY OTHER WARRANTY OR
CONDITION, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE
LOSS OR DAMAGE IS CAUSED BY SELLER’S OWN NEGLIGENCE OR FAULT AND EVEN IF SELL
ER HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH LOSSES OR DAMAGES. Any product description (whether in writing or
made orally by Seller or Seller’s agents), specifications, samples, models, bulletin, drawings, diagrams, engineering
sheets or similar materia
ls used in connection with the Buyer’s order are for the sole purpose of identifying the
Seller’s products and shall not be construed as an express warranty or condition. Any suggestions by Seller or
Seller’s agents regarding use, applications, or suitabil
ity of the products shall not be construed as an express
warranty or condition unless confirmed to be such in writing by Seller. Seller does not represent that the products it
sells may not be compromised or circumvented; that the products will prevent any
personal injury or property loss
by burglary, robbery, fire or otherwise, or that the products will in all cases provide adequate warning or protection.
Buyer understands that a properly installed and maintained alarm may only reduce the risk of a burglar
y, robbery or
fire without warning, but it is not insurance or a guarantee that such will not occur or will not cause or lead to
personal injury or property loss. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL
INJURY, PROPERTY DAMAGE OR OTHE
R LOSS BASED ON ANY CLAIM AT ALL INCLUDING A CLAIM THE
PRODUCT FAILED TO GIVE WARNING. However, if Seller is held liable whether directly or indirectly for any loss or
damage with respect to the products it sells, regardless of cause or origin, its maximum
liability shall not in any
case exceed the purchase price of the product, which shall be fixed as liquidated damages and not as a penalty,
and shall be the complete and exclusive remedy against the Seller. Should your product become defective during
the w
arranty, please contact your installer to facilitate repair or replacement with Seller pursuant to the terms
hereof. Seller reserves the right to replace any defective product under warranty with new, refurbished, or
remanufactured product.
78
NOTES
79
NOTES
80
NOTES
81
NOTES
Ê800-06905EŠ
800-
06905 6/10 Rev.
E
- Uploaded