Honeywell Vista 50P Programming Guide

Related Products

Honeywell Tuxedo Touch

Talking Color Graphic Wired Touchscreen Alarm Keypad

Honeywell Tuxedo Touch WIFI

Talking Color Graphic Touchscreen Alarm Keypad

Honeywell VISTA-50P

Alarm Control Panel

List Price: $702.00

Our Price: $433.99

Related Categories

Alarm Keypads

Document Transcript

VISTA SERIES VISTA-50P/VISTA-50PUL
Commercial Burglary Partitioned Security System With Scheduling Programming Guide

VISTA50P-PRV2 5/04 Rev B

Table of Contents
Recommended Programming Procedure................. 3 Program Field Index ................................................. 4 VISTA-50P/VISTA-50PUL Programming Form........ 5 Partition-Specific Fields.......................................... 10 Programming With #93 Menu Mode ...................... 12 Zone Programming................................................. 13 5800 Series Transmitters Loop Designations ........ 14 Expert Mode Zone Programming ........................... 15 Alpha Descriptors Programming ............................ 19 Alpha Descriptor Vocabulary.................................. 22 Device Programming.............................................. 23 Relay Programming................................................ 24 Relay Voice Descriptors ......................................... 27 Relay Voice Descriptors and Custom Word Substitutes Vocabulary........................................ 28 Custom Word Substitutes for VIP Module Annunciation........................................................ 29 System Layout Worksheets.................................... 30 Relay Devices Worksheets..................................... 38 Scheduling Menu Prompts ..................................... 40 Scheduling Worksheets.......................................... 41 VISTA-50P/VISTA-50PUL Summary of Connections Diagram.......................................... 46

The purpose of this document is to provide a quick and easy way to program your entire system. A recommended programming procedure is included, followed by a list of program fields with the corresponding program group they belong to (system-wide, partition-specific, scheduling, etc.). Two program forms are included. One contains all the programming fields, and the other contains the partition-specific fields. If you are setting up a single-partition system, the partition-specific fields become system-wide fields. Following the program forms are system layout worksheets. We recommend that you use these sheets to plan your system before programming is performed. If you need further information about specific programming options, see the VISTA-50P/VISTA-50PUL Installation and Setup Guide. Make sure that one two-line alpha keypad is connected to the control and is set to device address "00." Single-Partition System The system default is for a single-partition system. Use the VISTA-50P/VISTA-50PUL SINGLE PARTITION PROGRAMMING FORM when programming for single-partition usage. Follow the steps outlined in RECOMMENDED PROGRAMMING PROCEDURE of this document for proper programming procedure. Multiple-Partition System You must enter the number of partitions you are using in data field 2*00 to set the system for multiple partitions. Use the VISTA-50P/VISTA-50PUL SINGLE PARTITION and the PARTITION-SPECIFIC PROGRAM FORMS when programming the system for multiple partitions. Follow the steps outlined in RECOMMENDED PROGRAMMING PROCEDURE of this document for proper programming procedure. • • • • • • • • • SUMMARY OF PROGRAMMING COMMANDS To enter program mode, enter installer code + [8] + [0] + [0] To set standard defaults, press ,97 To change to next page of program fields, press ,94 To return to previous set of fields, press ,99 To erase account and phone number field entries, press [,] + field number + [,] To assign zone descriptors, press #93 + follow menu prompts To add custom words, press #93 + follow menu prompts To enter Installer's Message, press #93 + follow menu prompts To exit program mode, enter ,99 OR ,98: ,99 allows re-access to programming mode by installer code. ,98 prevents re-access to programming mode by installer code.

Standard default (,97) values are shown in brackets [ ], otherwise default = 0.

–2–

Recommended Programming Procedure
The following is a step-by-step procedure recommended for programming your VISTA-50P/VISTA-50PUL system. 1. Set the keypads (and other peripheral devices) to the appropriate addresses. 2. Set factory defaults by pressing ,97. This will automatically enable keypad addresses 00-03, so be sure at least one keypad is set to one of these addresses. 3. Program system-wide (global) data fields. Using the programming form as a guide, enter program mode and program all system-wide programming fields. These options affect the entire system, regardless of partitions. They include control options, downloader and dialer options, RF options, event logging options, etc. Refer to the Program Field Index for a listing of the program fields and their function. Note that field 2,00 (number of partitions) must be programmed before continuing. 4. Program partition-specific fields. When the system-wide fields have been programmed, program all partition-specific programming fields by first pressing ,91 to select a partition (while still in data field program mode). Then enter the first partitionspecific field number ,09. When you are finished, the next partition-specific field is automatically displayed. Partition-specific fields can have different values for each partition. To program the fields for the next partition, press ,91, enter the desired partition number, then enter field ,09. Refer to the PROGRAMMING section in the VISTA-50P/VISTA-50PUL Installation and Setup Guide for detailed instructions. 5. Use #93 Menu Mode for device programming. Refer to Device Programming in this guide to assign keypad ID numbers and default partitions for each keypad, and to selectively suppress certain keypad sounding options. Also use this mode to assign RF receivers, relay modules, and the VIP module. 6. Use #93 Menu Mode for zone programming. Refer to Zone Programming in this guide to program zone response types, assign right loop zones and wireless zones, assign zones to partitions, and to program alarm report codes. 7. Use #93 Menu Mode for programming outputs. Refer to Output Programming in this guide to program desired output operation. 8. Program Communication options. Refer to System Communication section in the VISTA-50P/VISTA-50PUL Installation and Setup Guide for detailed instructions. Then use #93 menu mode to program report codes. 9. Use #93 Menu Mode for programming alpha descriptors. Refer to Alpha Programming in this guide to enter zone and partition descriptors and a custom installer's message. 10. Use #93 Menu Mode for relay voice descriptors and custom word substitutes. Refer to Relay Voice Descriptors in this guide for further instructions for programming relay descriptors to be annunciated by the VIP module, as well as the Custom Index section for custom word substitutes. 11. Use #80 Mode for programming schedules. Refer to the Scheduling Menu Prompts in the VISTA-50P/VISTA-50PUL Installation and Setup Guide to program open/close schedules, temporary and holiday schedules, limitation of access schedules, and timedriven events. 12. Define user access codes. Refer to User Access Codes in the VISTA-50P/VISTA-50PUL Installation and Setup Guide to program authority level, O/C reporting option, partition assignments, and RF key assignments for each user. 13. Exit Programming Mode. Exit programming mode by pressing either ,98 or ,99. Additional entries of ,99 are required if the exit is being done from fields 1,00 and above. To prevent re-access to programming mode using the Installer's code, use ,98. The only way to re-access programming mode is by depressing both the [,] and [#] keys at the same time within 30 seconds of powerup. Exiting by using ,99 always allows reentry into programming mode using the Installer code. Either way of exiting allows access via downloading. Note that if local programming lockout is set via downloading, programming mode cannot be entered at the keypad.

–3–

Program Field Index
On the following pages, the programming fields have been arranged in numerical order. Use this index to cross-reference the fields on the programming form. Field Group Field Group Field Group *00 *02 *03 *04 *05 *09 *10 *11 *12 *13 *14 *15 *16 *17 *19 *20 *21 *22 *23 *24 *25 *26 *27 *28 *29 *30 *31 *32 *33 *34 *35 *36 *37 *38 *39 *40 *41 *42 *43 *44 *45 *46 *47 *48 *49 *50 *51 *52 *53 *54 *56 System-Wide # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode Partition-Specific Partition-Specific Partition-Specific Partition-Specific Partition-Specific System-Wide System-Wide Partition-Specific System-Wide System-Wide System-Wide System-Wide Partition-Specific Partition-Specific System-Wide System-Wide Communications Communications System-Wide Partition-Specific Communications Communications Partition-Specific Communications Communications System-Wide System-Wide System-Wide Partition-Specific Partition-Specific Communications System-Wide Communications Communications Communications Communications Communications Communications Communications Communications Communications Communications Communications Communications # 93 Menu Mode # 93 Menu Mode *57 *58 *59 *60 *61 *62 *63 *64 *65 *66 *67 *68 *69 *70 *71 *72 *73 *74 *75 *76 *77 *78 *79 *80 *81 *82 *83 *84 *85 *87 *88 *89 *90 1*01 1*02 1*03 1*04 1*05 1*06 1*07 1*08 1*09 1*17 1*18 1*19 1*20 1*21 1*22 1*23 1*24 1*25 # 93 Menu Mode Communications # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode Communications # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode Communications # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode Communications # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode Communications Communications Communications Communications Communications Communications Partition-Specific Partition-Specific Partition-Specific Partition-Specific Communications Partition-Specific # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode System-Wide Partition-Specific Partition-Specific System-Wide System-Wide System-Wide System-Wide System-Wide System-Wide 1*28 1*29 1*30 1*31 1*33 1*34 1*35 1*36 1*37 1*38 1*39 1*40 1*41 1*42 1*43 1*44 1*45 1*46 1*47 1*48 1*49 1*52 1*53 1*57 1*58 1*60 1*70 1*71 1*72 1*73 1*74 1*75 1*76 2*00 2*01 2*02 2*05 2*06 2*07 2*08 2*09 2*10 2*11 2*13 2*14 2*18 2*19 2*20 2*21 System-Wide System-Wide System-Wide System-Wide Communications Communications # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode # 93 Menu Mode Communications Communications Communications Communications Partition-Specific System-Wide Partition-Specific System-Wide Partition-Specific System-Wide System-Wide Partition-Specific System-Wide System-Wide System-Wide System-Wide System-Wide System-Wide System-Wide System-Wide System-Wide System-Wide Partition-Specific System-Wide System-Wide System-Wide Partition-Specific Partition-Specific Partition-Specific Partition-Specific Partition-Specific Partition-Specific System-Wide Communications Communications Partition-Specific System-Wide Partition-Specific System-Wide

–4–

VISTA-50P/VISTA-50PUL Programming Form
Some fields are programmed for each partition (shown as shaded fields). If you are programming a multiple-partition system, see the Partition-Specific Fields section for programming these fields. Standard default (*97) values are shown in brackets [ ].

*00 INSTALLER CODE
Enter 4 digits, 0-9 [4140]

| | |

*25 BURG.TRIGGER FOR RESPONSE TYPE 8
1=enable; 0=disable

[1] [0]

*02 ! *05

RESPONSE TYPES FOR ZONES
Skip these fields. Use #93 Menu Mode, Zone Programming to program the response types.

*26 INTELLIGENT TEST REPORTING

*09 ENTRY DELAY #1
00, 01-15 times 15 seconds Maximum "03" for UL.

[02]

| | | | |
[0]

1=yes (no report sent if any other report was recently sent); 0=no (send report at programmed interval, field *27) Must be 0 for UL installations.

*27 TEST REPORT INTERVAL
[03]

[024]

| |
[1] [1] [0]

*10 EXIT DELAY #1
00, 01-15 times 15 seconds Maximum "04" for UL installations.

Enter interval in hours, 001-999; 000=no report; Max. 024 for UL installations.

*28 POWER UP IN PREVIOUS STATE
[06]
1=yes; 0=no; "1" for UL installations.

*11 ENTRY DELAY #2

00, 01-15 times 15 seconds (must be longer than Entry Delay #1). Maximum "03" for UL installations.

*29 QUICK ARM
1=yes; 0=no

*12 EXIT DELAY #2

[08]

*30 TOUCHTONE OR ROTARY DIAL
1=TouchTone; 0=rotary

00, 01-15 times 15 seconds (must be longer than Exit Delay #1). Maximum "04" for UL installations.

*13 ALARM SOUNDER DURATION

*31 PABX ACCESS CODE *32 PRIM. SUBS. ACCT #
[15 15 15 15] 00-09; B-F (11-15)

| |

[04]

01-15 times 2 minutes. Must be minimum 16 minutes for UL installations.

*14 ZONE 9 RESPONSE TIME
Enter 1 for fast response time 10ms Enter 0 for normal response time 350ms. Must be 0 for UL installations.

*33 PRIMARY PHONE NUMBER
[0]
Enter 0-9 for each digit. Enter #11 for *, #12 for #, #13 for 2-second pause

Enter 00-09; B-F (11-15)

*15 KEYSWITCH ASSIGNMENT
Enter partition in which keyswitch used, 1-8; 0=disable

*16 CONFIRMATION OF ARMING DING
1=enable; 0=disable. Must be "1" for UL Installations.

[0]

*34 SECONDARY PHONE NUMBER

*17 AC LOSS KEYPAD SOUNDING
1=yes; 0=no

[0] [0]

*19 RANDOMIZE AC LOSS REPORT *20 VIP MODULE PHONE CODE
Enter 01 - 09 for the first digit; enter 11 for “*” or 12 for “#” for the second digit. Must be set to "0" for UL installations.

*35 DOWNLOAD PHONE NO.

Enter 0-9 for each digit. Enter #11 for *, #12 for #, #13 for 2-second pause

1=10-40 min; 0=normal report (about 2 min. after AC loss).

|
[00],

|
[11] Enter 0-9 for each digit. Enter #11 for *, #12 for #, #13 for 2-second pause

*21 PREVENT FIRE TIMEOUT
1=No timeout; 0=Timeout.

[0] [001]
95 96 99

*36 DOWNLOAD ID NO.
| | |

*22 KEYPAD PANIC ENABLES
1=enable; 0=disable

*37 DOWNLOAD COMMAND ENABLES
[1] [0]

Enter 00-09; A-F (10-15) [15 15 15 15 15 15 15 15]

*23 MULTIPLE ALARMS
1=yes; 0=no

0
Dlr ShtdwnSys Shtdwn Not UsedRmt BypRmt DisarmRmt ArmUpld PgmDwnld Pgm

*24 IGNORE EXPANSION ZONE TAMPER

See field 1*53 for Callback disable option; [1=enable]; 0=disable. For UL installations, all entries must be "0."

1=Ignore; 0=Enable tamper for RF and V-Plexs. Must be "0" for UL installations if using these devices.

*38 PREVENT ZONE XX BYPASS

[00]

01-86; 00 if all zones (except fire zones) can be bypassed

–5–

*39 ENABLE OPEN/CLOSE REPORT FOR
INSTALLER CODE 1=enable; 0=disable

[0] [0]

*58 SUPERVISORY AND RESTORE CODES FOR ZONES
01-16. Enter 00-09; B-F (11-15). Default = [00 00 00 00 00]

*40 OPEN/CLOSE REPORT FOR KEYSWITCH
1=enable; 0=disable

|
Alarm Rst

|
Trbl

|
Trbl Rst

|
Byp

|
Byp Rst

*59 ! *62
[1]

*41 NORMALLY CLOSED or EOLR (Zones 2-8)
1=N.C.loops; 0=EOLR supervision. Must be "0" for UL installations.

ALARM REPORT CODES & ID DIGITS FOR ZONES 17-32.
Skip these fields. Use #93 Menu Mode, Zone Programming to program the report codes.

*63 SUPERVISORY AND RESTORE CODES FOR ZONES
[0] 17-32. Enter 00-09; B-F (11-15). Default = [00 00 00 00 00]

*42 DIAL TONE PAUSE
0=5 seconds; 1=11 seconds; 2=30 seconds. Must be "0" UL Installations.

|
Alarm Rst

|
Trbl

|
Trbl Rst

|
Byp

|
Byp Rst

*43 DIAL TONE DETECTION
1=wait for true dial tone; 0=pause, then dial

[1] [00]

*64 ! *67

ALARM REPORT CODES & ID DIGITS FOR ZONES 33-48.
Skip these fields. Use #93 Menu Mode, Zone Programming to program the report codes.

*44 RING DETECTION COUNT

|
[1]

01-14; 15=answering machine; 00=no detection. Must be "00" for UL Burglary.

*68 SUPERVISORY AND RESTORE CODES FOR ZONES
33-48. Enter 00-09; B-F (11-15). Default = [00 00 00 00 00]

*45 PRIMARY FORMAT

|
Alarm Rst

|
Trbl

|
Trbl Rst

|
Byp

|
Byp Rst

0=Low Speed; 1=Contact ID; 2=ADEMCO High Speed; 3= ADEMCO Express

*69 ! *72

*46 LOW SPEED FORMAT (Primary)
0= ADEMCO Low Speed; 1=Sescoa/Radionics

[0] [1]

ALARM REPORT CODES & ID DIGITS FOR ZONES 49-64.
Skip these fields. Use #93 Menu Mode, Zone Programming to program the report codes.

*47 SECONDARY FORMAT

*73 SUPERVISORY AND RESTORE CODES FOR ZONES
49-64. Enter 00-09; B-F (11-15). Default = [00 00 00 00 00]

0=Low Speed; 1=Contact ID; 2= ADEMCO High Speed; 3= ADEMCO Express

|
Alarm Rst

|
Trbl

|
Trbl Rst

|
Byp

|
Byp Rst

*48 LOW SPEED FORMAT (Sec.)
0= ADEMCO Low Speed; 1=Sescoa/Radionics

[0] [0] [0]
Prim Sec

*74 ! *77

ALARM REPORT CODES & ID DIGITS FOR ZONES 81-99.
Skip these fields. Use #93 Menu Mode, Zone Programming to program the report codes.

*49 CHECKSUM VERIFICATION
1=yes; 0=no

*78 SUPERVISORY AND RESTORE CODES FOR ZONES
81-99. Enter 00-09; B-F (11-15). Default = [00 00 00 00 00]

*50 SESCOA/RADIONICS SELECT
1=Sescoa; 0=Radionics

[0] [0]

|
Alarm Rst

|
Trbl

|
Trbl Rst

|
Byp

|
Byp Rst

*51 DUAL REPORTING

*52 STANDARD/EXPANDED REPORT FOR PRIMARY
[0 0 0 0 0 0]
Alarm Rstr Byp Trbl O/C LoBat

1=yes; 0=no If used with Spilt Reporting "1" option (1*34), alarms and alarm restores go to both primary & secondary numbers, while all other reports go to secondary only. If used with Split Reporting "2" option, alarms and alarm restores go to both, open/close and test messages go to secondary only, while all other reports go to primary.

ZONE TYPE RESTORE ENABLES

*79 FOR ZONE TYPES 1-8
1 2 3 4 5 1=enable; [0=disable] 6 7 8

*80 FOR TYPES 9, and 10
1=enable; [0=disable]
9 10

*53 STANDARD/EXPANDED REPORT FOR SECONDARY
[0 0 0 0 0 0]
Alarm Rstr Byp Trbl O/C LoBat

0=standard; 1=expanded; Note: Expanded overrides 4+2 format.

*81 ! *82

SYSTEM NON-ALARM CODES
Enter 00-09; B-F (11-15). Default = 00 for all reports *81 1st Digit
Close Open Low Battery Low Battery Restore AC Loss

*82 2nd Digit

0=standard; 1=expanded;

*54 ! *57

ALARM REPORT CODES & ID DIGITS FOR ZONES 01-16.
Skip these fields. Use #93 Menu Mode, Zone Programming to program the report codes.

| | | | |

–6–

AC Restore Test Power Up Cancel Program Tamper

| | | | | | |
[01]

| | | | | | |

1*23 CROSS-ZONING PAIR TWO 1*24 CROSS-ZONING PAIR THREE 1*25 CROSS-ZONING PAIR FOUR

| | |

MISCELLANEOUS WIRELESS OPTIONS Fields 1*28 - 1*31 are not applicable for UL installations.

1*28 RF TX LOW BATTERY SOUND
1=immediate; 0=when disarmed

[0] [0] [06] [12] [0] [0]

*83 FIRST TEST REPORT TIME

[Day 00; hour 12; min 00] Days 01-07 Hours 00-23 Min 0059; 00 in all boxes = instant (Day 01= Monday)

1*29 RF TX LOW BATTERY REPORTING
1=enable; 0=disable

*84 SWINGER SUPPRESSION
01-15 alarms Must be "00" (disabled) for UL. 1=enable; [0=disable]
95

1*30 RF RCVR CHECK-IN INTERVAL
02-15 times 2 hours; 00 disables supervision

| |

*85 ENABLE DIALER REPORTS FOR PANICS & DURESS
96 97 Duress

1*31 RF XMITTER CHECK-IN INTERVAL 1*33 TOUCHTONE W/ROTARY BACKUP
1=enable; 0=disable

02-15 times 2 hours; 00 disables transmitter supervision

*87 ENTRY WARNING
1=continuous; 0=3 beeps

[1] [0]

1*34 COMM. SPLIT REPORTING

*88 BURG. ALARM COMM. DELAY
1=16 seconds; 0=no delay Must be "0" for UL installations.

0=no; 1=alarms and alarm restores primary, others secondary; 2=open/close, test secondary, others primary. See /51 for comments if using with dual reporting.

1*35 ! 1*38 ALARM REPORT CODES & ID DIGITS FOR
[0] ZONES 65-80.
Skip these fields. Use #93 Menu Mode, Zone Programming to program the report codes.

*89 RESTORE REPORT TIMING

0=Instant; 1=After bell timeout if zone is restored; 2=when system is disarmed. Must be "0" for UL installations.

*90 SEC. SUBS. ACCT #
Enter 00-09; B-F (11-15)

|
[15 15 15 15]

1*39 SUPERVISORY AND RESTORE CODES FOR
ZONES 65-80. Enter 00-09; B-F (11-15).
Default = [00 00 00 00 00]

2nd Page Programming Fields (press *94) 1*01 ! 1*09 ASSIGN RESPONSE TYPE FOR ZONES.
Skip these fields. Use #93 Menu Mode, Zone Programming to program the response types.

|
Alarm Rst

|
Trbl

|
Trbl Rst

|
Byp

|
Byp Rst

1*40 ! 1*41 NON-ALARM DIALER CODES
Enter 00-09; B-F (11-15). Default = 00 for all reports 1*40 1st Digit
Armed STAY

1*17 LOBBY PARTITION
Enter the "common lobby" partition (1-8)

[0] [0]

1*41 2nd Digit

| | | | | | |
[0] [0]

| | | | | | |

1*18 AFFECTS LOBBY

Enter 1 if this partition affects the common lobby; enter 0 if it does not. Must be "0" for UL installations.

Time/Date Set or Event Log Reset Event Log 50% & 90% Full Event Log Overflow Exit Error (Zone) Exit Error (User) Recent Close

1*19 ARMS LOBBY

[0]

Enter 1 if arming this partition attempts to arm lobby; enter 0 if it does not. Must be "0" for UL installations.

1*20 EXIT ERROR LOGIC ENABLE

[0]

0=No; 1=Bypass E/E and Interior zones faulted after exit delay. Must be "0" for UL installations.

1*21 EXIT DELAY RESET

[0]

1*42 CALL WAITING DEFEAT
1=Yes; 0=No

0=No; 1=Resets Exit Delay to programmed value after zone is closed and then faulted prior to end of exit delay. Must be "0" for UL installations.

1*43 PERM. KEYPAD BACKLIGHT

FIELDS 1. 22-1.25: Allow four sets of two zones each to be linked so that both must fault within a 5-minute period to cause an alarm. Default for these fields = [00], [00].

1=enable; 0=disable: When disabled, display lights when any key is pressed, and turns off after period of keypad inactivity.

1*22 CROSS-ZONING PAIR ONE

1*44 WIRELESS KEYPAD TAMPER
DETECTION

[0]

–7–

1=enable; 0=disable. Must be "0" for UL installations.

1*74 RELAY TIMEOUT XXX MINUTES [000]
[0]

| |

1*45 EXIT DELAY SOUNDING

1=enable; 0=disable. Produces rapid beeping during exit delay if enabled.

Enter the relay timeout, 000-127 in multiples of 2 minutes, desired for #80 Menu Mode time-driven event relay command numbers "04/09" and #93 Menu Mode Output Programming output command "56."

1*46 AUXILIARY OUTPUT MODE

[0]

1*75 RELAY TIMEOUT YYY SECONDS [000]

| |

Enter 0 for ground start output. Enter 1 for open/close trigger (is produced only if all partitions are armed. Enter 2 for keypad-like sounding. Applies to the partition enabled in field *15. Enter 3 if AAV module is being used. NOTE: Only one of the above options may be active within the system.

Enter the relay timeout, 000-127 seconds, desired for #80 Menu Mode time driven event relay command numbers "05/10" and #93 Menu Mode Output Programming command "57."

1*76 ACCESS CONTROL RELAY

[00]

1*47 CHIME ON EXTERNAL SIREN
1=enable; 0=disable

[0] [0]

Relay will be pulsed for 2 seconds whenever code + [0] is pressed. Enter 00-16; 00=none. Must be "00" for UL installations.

3rd Page Programming Fields (press *94) 2*00 NUMBER OF PARTITIONS
Enter 1-8

1*48 WIRELESS KEYPAD ASSIGNMENT

[1]

0=disable; enter partition in which RF keypad used, 1-8. Must be "0" for UL installations.

1*49 SUPPRESS TX SUPERVISION SOUND
1=disable; 0=enable. Must be "0" for UL installations.

[1]

2*01 DAYLIGHT SAVING TIME [04, 10]
START/END MONTH

|
Start

|
End

00-12; if no daylight saving time, enter 00, 00

1*52 SEND CANCEL IF ALARM + OFF
1=no restriction; 0=within bell timeout period only

[1] [0]

2*02 DAYLIGHT SAVING TIME
START/END WEEKEND

[1, 5]

1*53 DOWNLOAD CALLBACK
1=callback not required; 0=callback required. Must be "0" for UL installations.

Enter 1-7. 1=first; 2=second; 3=third; 4=fourth; 5=last; 6=next to last; 7=3rd from last [1, 5]

Start | End

2*05 AUTO-ARM DELAY
[0] [0]

[15]

1*57 5800 RF BUTTON GLOBAL ARM
1=enable; 0=disable

Enter the time between the end of the arming window and the start of auto-arming warning period, in values of 1-14 times 4 minutes 00=instant; [15=no auto arm at all]. When this delay expires, the Auto-Arm Warning Period begins.

1*58 5800 RF BUTTON FORCE ARM

2*06 AUTO-ARM WARNING PERIOD

[15]

Enter "1" to enable. If a zone is faulted after pressing button, keypad will beep once. Pressing the button again within 4 sec. bypasses the zone. Enter "0" to disable. Must be "0" for UL installations.

This is the time during which the user is warned to exit the premises prior to the auto-arming of the system (beeps every 15 seconds; "ALERT" displayed). Enter 01-15 minutes. 00=instant at end of arming delay.

1*60 ZONE 5 AUDIO ALARM VERIFICATION

[0]

2*07 AUTO-DISARM DELAY

[15]

Enter 1 If 2-way audio (AAV) is being used; Enter 0 if it is not. Must be "0" for UL installations.

This is the time between the end of the disarming window and the start of auto-disarming. Enter 01-14 times 4 minutes; 00=instant at end of window; 15=no auto-disarm.

1*70 EVENT LOG TYPES
[1 0 0 0 1]
Alarm Chk Byp O/C Syst

2*08 ENABLE FORCE ARM FOR AUTO-ARM
0=disable; 1=enable

[0]

2*09 OPEN/CLOSE REPORTS BY EXCEPTION [0]
[0] [0] [0]
1=enable; 0=disable If enabled, only openings and closings occurring outside the scheduled opening/closing windows will trigger dialer reports. Opening reports will also be suppressed during the closing window, in order to prevent false reports when the user arms the system and then reenters the premises to retrieve a forgotten item.

1=enable; 0=disable

1*71 12/24 HOUR TIME STAMP FORMAT
0=12 hour; 1=24 hour

1*72 EVENT LOG PRINTER ON-LINE
0=disable; 1=enable

1*73 PRINTER BAUD RATE
1=300; 0=1200

2*10 ALLOW DISARMING ONLY DURING
ARMING/DISARMING WINDOWS

[0]

0=disable; 1=enable See system-wide field 2*11 if enabling field 2*10. This feature adds high security to the installation.

–8–

2*11 ALLOW DISARM OUTSIDE WINDOW
IF ALARM OCCURS

[0]

2*18 ENABLE GOTO FOR THIS PARTITION
1=Allow log-on from other partitions; 0=disable

[0] [0] [1]

2*13 ! 2*14 SCHEDULING RELATED REPORT CODES
Enter 00-09; B-F (11-15). Default = 00 for all reports 2*13 1st Digit
Early Opening Early Closing Late Opening Late Closing No Opening (late to open) No Closing (late to close) Auto-Arm Failure Access Schedule Changed

Used only if field 2*10 (partition-specific field) is set to "1." If this field is enabled ("1") the system can be disarmed outside the disarm window if an alarm has occurred. If "0," disarming can only be done during the disarm window. If field 2*10 is set to "0" for a partition, this field has no effect for that partition.

2*19 USE PARTITION DESCRIPTORS
0=disable; 1=enable

2*20 ENABLE J7 TRIGGERS FOR PARTITION 2*21 ENABLE SUPERVISION PULSES FOR LRR

0=disable for displayed partition; 1=enable for displayed partition

2*14 2nd Digit

| | | | | | | |

| | | | | | | |
• • • • • • • • •

TRIGGER OUTPUTS

[000]

| |
B P

Used for supervised connection to 7845i-ent. F Enter 0 to disable or 1 to enable the listed outputs. F= Fire; B= Burglary; P= Silent Panic/Duress. Must be 1 for UL installations.

SUMMARY OF PROGRAMMING COMMANDS To enter program mode, enter installer code + [8] + [0] + [0] To set standard defaults, press *97 To change to next page of program fields, press *94 To return to previous set of fields, press *99 To erase account and phone number field entries, press [*] + field number + [*] To assign zone descriptors, press #93 + follow menu prompts To add custom words, press #93 + follow menu prompts To enter Installer's Message, press #93 + follow menu prompts To exit program mode, enter *99 OR *98: *99 allows reaccess to programming mode by installer code. *98 prevents re-access to programming mode by installer code.

–9–

Partition-Specific Fields
(Duplicate this page for each partition in the installation.) To program these fields, 1. Press *91 to select a partition. 2. Enter a partition-specific field number (ex. *09). 3. Make the required entry. 4. Repeat steps 1-3 for each partition in the system. PARTITION #____ PROGRAM FIELDS
1st Page Fields

*87
[02]

ENTRY WARNING
1=continuous; 0=3 beeps

[1] [0]

*09

ENTRY DELAY #1
00, 02-15 times 15 seconds. Maximum 03 for UL Listed installations.

|
*88

BURG. ALARM COMM. DELAY
1=16 seconds; 0=no delay. Must be "0" for UL installations. Must be “1” for SIA installations.

*10

EXIT DELAY #1
00, 03-15 times 15 seconds. Maximum 04 for UL Listed installations.

[03]

|
*90

SEC. SUBS. ACCT #
Enter 00-09; B-F (11-15)

*11

ENTRY DELAY #2
00, 02-15 times 15 seconds. Maximum 03 for UL installations.

[06]

| | |
[0]

[15 15 15 15]

2nd Page Programming Fields (press *94) [08]

*12

EXIT DELAY #2
00, 03-15 times 15 seconds. Maximum 04 for UL installations.

1*18 AFFECTS LOBBY

[0]

Enter 1 if this partition affects the common lobby; enter 0 if it does not.

*13

ALARM SOUNDER DURATION

[04]

1*19 ARMS LOBBY

[0]

01-15 times 2 minutes. Must be set to a minimum of 16 minutes for UL installations.

Enter 1 if arming this partition attempts to arm lobby; enter 0 if it does not

*16

CONFIRMATION OF ARMING DING
1=enable; 0=disable. Must be "1" (enable) for UL installations.

1*20 EXIT ERROR LOGIC ENABLE

[0]

*22 *23

0=No; 1=Bypass E/E and Interior zones faulted after exit delay. Must be "0" (no) for UL installations.

KEYPAD PANIC ENABLES
1=enable; 0=disable

[001] 995 996 999 [1]

1*21 EXIT DELAY RESET

[0]

MULTIPLE ALARMS
1=yes; 0=no. Must be 1 (yes) for UL installations.

0=No; 1=Resets Exit Delay to programmed value after zone is closed and then faulted prior to end of exit delay. Must be "0" (no) for UL installations.

1*43 PERM. KEYPAD BACKLIGHT
[1]

[0]

*29 *32 *38 *39

QUICK ARM
1=yes; 0=no

1=enable; 0=disable. When disabled, display lights when any key is pressed, and turns off after period of keypad inactivity.

PRIM. SUBS. ACCT #

|
[00] [0]

| |

1*45 EXIT DELAY SOUNDING

[0]

Enter 00-09; B-F (11-15) [15 15 15 15]

PREVENT ZONE XX BYPASS ENABLE OPEN/CLOSE REPORT
1=enable; 0=disable

1=enable; 0=disable. When enabled produces quick beeping during exit delay.

01-86; 000 if all zones (except fire zones) can be bypassed

1*47 CHIME ON EXTERNAL SIREN
1=enable; 0=disable

[0]

FOR INSTALLER CODE [01]

1*52 SEND CANCEL IF ALARM + OFF

[1]

*84 *85

SWINGER SUPPRESSION
01-15 alarms; Must be "00" (disabled) for UL installations.

1=no restriction; 0=within Bell Timeout period only

1*76 ACCESS CONTROL RELAY FOR PART.[00]

ENABLE DIALER REPORTS FOR PANICS & DURESS
1=enable; [0=disable]
995 996 999 Duress

Relay will be pulsed for 2 seconds whenever code + [0] is pressed. Enter 00-16; 00=none. Must be "00" (none) for UL installations.

– 10 –

3rd Page Programming Fields (press *94)

2*10 ALLOW DISARMING ONLY DURING
[15]

[0]

2*05 AUTO-ARM DELAY

See system-wide field 2*11 if enabling field 2*10. This feature adds high security to the installation. 0=disable; 1=enable

ARMING/DISARMING WINDOWS

2*06 AUTO-ARM WARNING PERIOD

[15]

2*18 ENABLE GOTO FOR THIS PARTITION
1=Allow log-on from other partitions; 0=disable

[0] [1]

2*20 ENABLE J7 TRIGGERS BY PARTITION

0=disable for displayed partition; 1=enable for displayed partition

2*07 AUTO-DISARM DELAY

[15]

|
• • • • • • • • •

This is the time between the end of the disarming window and the start of auto-disarming. Enter 01-14 times 4 minutes; 00=instant at end of window; 15=no auto-disarm

2*08 ENABLE FORCE ARM FOR AUTO-ARM
0=disable; 1=enable

[0]

2*09 OPEN/CLOSE REPORTS BY EXCEPTION [0]
1=enable; 0=disable: If enabled only openings and closings occurring outside the scheduled opening/closing windows will trigger dialer reports. Opening reports will also be suppressed during the closing window, in order to prevent false reports when the user arms the system and then reenters the premises to retrieve a forgotten item.

– 11 –

Programming With #93 Menu Mode
NOTE: The following field should be preset before beginning: 2*00 Number of Partitions. In addition, receivers should be programmed via Device programming. After programming all system related programming fields in the usual way, press #93 while still in programming mode to display the first choice of the menu driven programming functions. Press 0 (NO) or 1 (YES) in response to the displayed menu selection. Pressing 0 will display the next choice in sequence. #93 MENU MODE KEY COMMANDS The following is a list of commands used while in the menu mode. #93 Enters Menu mode [,] Serves as ENTER key. Press to have keypad accept entry. [#] Backs up to previous screen. 0 Press to answer NO 1 Press to answer YES 01-09 All data entries are either 1-digit or 2-digit entries. 00 Exits menu mode, back into field programming mode, when entered at the first question for each category. Menu selections are as follows:

PROMPT
ZONE PROG? 1 = YES 0 = NO

EXPLANATION
For programming the following: • Zone Number • Zone Response Type • Partition Number for Zone • Dialer report code for zone • Input Device Type for zone (whether RF, polling loop, etc.) • Enrolling serial numbers of 5800 Series transmitters & serial polling loop devices into the system. Same as Zone Programming except: • Done with a minimum number of keystrokes. • Can program wireless keys using pre-defined templates. For entering alpha descriptors for the following: • Zone Descriptors • Installer's Message • Custom Words • Partition Descriptors • Relay Descriptors For defining the following device characteristics for addressable devices, including keypads, RF receivers (5881), output relay modules (4204), and 4286 VIP Module: • Device Address • Device Type • Keypad Options (incl. partition assignment) • RF House ID For defining output relay functions. 0 For entering voice descriptors for relays to be used with the 4286 VIP Module. 0 For creating custom word substitutes for VIP Module annunciation. 0

EXPERT MODE? 1 = YES 0 = NO

ALPHA PROG? 1 = YES 0 = NO

DEVICE PROG? 1 = YES 0 = NO

RELAY PGM? 1 = YES 0 = NO RLY VOICE DESCR? 1 = YES 0 = NO CUSTOM INDEX ? 1 = YES 0 = NO

– 12 –

Zone Programming
If using 5800 Series transmitters, do not the install batteries until you are ready to enroll them. After enrolling the transmitter, the battery need not be removed. This is to prevent enrolling the wrong serial number.

PROMPT
ZONE PROG? 1 = YES 0 = NO SET TO CONFIRM? 1 = YES 0 = NO

EXPLANATION
Press 1 to enter ZONE PROGRAMMING mode. The following screens appear. Press [,] to display the next screen. Press # to display a previous screen. This prompt appears once upon entering Zone Programming Mode. If “Yes,” Confirmation prompts will be displayed after the device’s Serial and Loop numbers have been entered later. Enter the 2-digit zone number to be programmed, as follows: Protection Zones = 01–86 System Supervisory Zones = 88, 89, 90, 91, 92 (duress), 97 and 98 (bell supervision) Keypad Panic Zones = 95, 96, 99 Press [,] to continue. This display appears, showing a summary of the zone's current programming. ZT = Zone Type, P = Partition, RC = Report Code, In = the input type of device, and L = the device's loop number to which the sensor is connected. Some devices can support more than one zone by means of individual loops (for example, 5801, 5804, 5816, 5817, etc.). If the zone is not programmed, the display appears as shown here. If you are checking a zone's programming, and it is programmed satisfactorily, press [#] to back up one step and enter another zone number, if desired. Press [,] to continue. Each zone must be assigned a zone type, which defines the way in which the system responds to faults in that zone. Refer to the Zone Type Definitions section in the ADEMCO VISTA-50P/VISTA-50PUL Installation and Setup Guide for detailed definitions of each zone type. Enter the zone type desired (or change it, if necessary). Available zone types are listed below. 00 = Assign for Unused Zones 01 = Entry/Exit #1, Burglary 02 = Entry/Exit #2, Burglary 03 = Perimeter, Burglary 04 = Interior Follower, Burglary 05 = Trouble Day/Alarm Night 06 = 24 Hr. Silent Alarm 07 = 24 Hr. Audible Alarm Press [,] to continue. Enter the partition number (1–8) you are assigning this zone to. Press [,] to continue. Enter the report code. The report code consists of 2 hexadecimal digits, each in turn consisting of 2 numerical digits. For example, for a report code of "3C," enter 03 for "3" and 12 for "C." (Refer to the System Communication section in the Installation and Setup Guide for more information about report codes and reporting formats.) Press [,] to continue. 08 = 24 Hr. Auxiliary 09 = Fire Without Verification 10 = Interior Delay, Burglary 20 = Arm–STAY† 21 = Arm AWAY† 22 = Disarm† 23 = No Alarm Response (e.g., relay activation)

ENTER ZONE NO. 00 = QUIT

Zone 10 entered ↑

10 ZT P RC In L 00 1 10 00 1

10 ZONE TYPE PERIMETER

Zone number 10 and Zone Type 03 entry shown † These are special zone types used with 5800 Series Wireless Pushbutton Units that result in arming the system in the STAY or AWAY mode, or disarming the system, depending on the selection made.

10 Partition 1 10 REPORT CODE 1st 03 2nd 12

– 13 –

PROMPT
10 INPUT TYPE RF Xmitter

EXPLANATION
Enter the input device type as follows: 00 = not used 01 = hardwired 03 = supervised RF transmitter (RF type) 04 = unsupervised RF transmitter (UR type) 05 = RF button-type transmitter (BR type) 06 = serial number polling loop device (SL type) 07 = DIP switch-type polling loop device 08 = right loop of DIP switch type device Right loops refer to the use of the right loop on a 4190WH Zone Expander Module and/or 4278 PIR, which allow hardwired devices to be monitored by the polling loop. If you are programming hardwired or DIP switch polling loop devices, the summary display appears after completing this entry. Press [,] to continue. For Serial Number entry and Loop Number entry, do one of the following: a. Transmit two open and close (or close and open) sequences. For a button-type transmitter, press and release the button, wait approximately 4 seconds, then press and release the button a second time. OR b. Manually enter the 7-digit serial number printed on a label on the transmitter, using the Alpha keypad. Then press the [,] key, the cursor moves to the “L” position. You can edit the loop number, if necessary. When the loop number is acceptable, press [,]. OR c. Press key [C] to copy the last serial number enrolled (used when programming a transmitter with several input loops). Press [,] to accept. The cursor will then move to the Loop column (L) with the previously entered/transmitted serial number displayed. Enter the loop number (refer to 5800 Series Transmitters Loop Designations below). To Delete an Existing Serial Number, in the loop number field, enter “0“. The serial number will change to “0”s. If “0” was entered in error, simply re-enter the loop number or press [#], and the serial number will return to the display. Press [,] to accept. The system will then check for a duplicate serial/loop number combination. If a duplicate serial/loop number combination is found, the keypad will emit a single long beep, and display the serial number along with a “?” for the loop number, allowing you to re-enter the correct loop number. If the serial/loop number combination is not a duplicate in the system, a display appears showing the serial number and loop number entry. Press [,] to continue.

Input types 4 & 5 are valid for certain 5800 Series transmitters only (e.g., 5801, 5802, 5802CP & 5803).

10 INPUT S/N: AXXX-XXXX

L 1

10 INPUT S/N: A022-4064

L 1

10 INPUT S/N: A022-4064

L 1

XMIT TO CONFIRM PRESS ,TO SKIP

Confirmation Option: This prompt only appears if you answered “Yes” at the first prompt. The system enters a confirmation mode so that the operation of the actual programmed input can be confirmed. Activate the loop input or button that corresponds to this zone. At any time during this step, you may press the [,] key on the keypad to save the serial and loop number combination without confirming. 1 If the serial number transmitted does not match the serial number entered, a display similar to the one at the left appears. If the loop number does not match, it is also displayed. If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary display does not appear), press the [#] key twice and then enter or transmit the correct serial number. If the serial number transmitted does match the serial number entered, the system beeps 3 times and a summary display appears, showing that zone’s programming. Note that an “s” indicates that a transmitter’s serial number has been enrolled. Press [,] to accept the zone information. The system now returns to the “ENTER ZONE NO.” prompt for the next zone. When all zones have been programmed, enter “00” to quit.

Entd Rcvd

A022-4063 A022-4064

10 ZT P RC In L 03 1 3C RF 1s

ENTER ZONE NO. 00 = QUIT

– 14 –

After you have enrolled each wireless device, remove ONE of the serial number labels from that device and affix it in the appropriate column on the worksheets provided later in this Programming Guide; then enter the other information (zone number, zone type, etc.) relevant to that device. When you have finished programming all zones, test each using the system's Test Mode. Do not use the Transmitter ID Sniffer Mode. The system checks only for transmission of one zone on a particular transmitter, NOT the zones assigned to each additional loop, and also does not verify polling loop type zones.

Expert Mode Zone Programming
Expert mode allows you to program zones using the minimum number of screens and keystrokes.

Expert Mode Zone Programming does not provide the capability to program some of the zone’s attributes, such as Arm w/Fault, Vent Zone, STAY mode, Auto-STAY, Bypass Group, etc. If you want to program a zone for any of these attributes, you must use Zone Programming.

Enter the Programming mode with [Installer Code] + 8 0 0 Before programming your zones, do the following: 1. Program field 2,00: Number of Partitions. 2. Enable your RF Receiver in Device Programming menu mode. To program your zones, press ,93 to display the "ZONE PROG?" prompt. Enter “0” (NO) to each prompt until the “EXPERT MODE?” prompt appears.

PROMPT
EXPERT MODE? 1 = YES 0 = NO SET TO CONFIRM? 0 = NO 1 = YES

EXPLANATION
Press 1 to enter Expert mode. 0 This prompt appears once upon entering Expert Mode. If you select “Yes,” Confirmation prompts will be displayed after the device’s Serial and Loop numbers have been entered later. A summary display appears, showing zone 1’s current programming or default values.

Zn ZT P RC In 01 03 1 10 HW Zn 10

L -

ZT P RC In L 03 1 10 RF 1s

Enter the desired 2-digit zone number and press [,]. Note: If you want to exit the Expert mode, enter “00” + [,]. If an “s” appears after the loop number, it indicates that the transmitter’s serial number has been enrolled. Use the [D] key to enter and duplicate wireless keys (see “Entering Wireless Keys” later) Enter all zone information except for Loop number, or press “C” to copy the zone information on this screen from the last saved zone (including Loop). ZT = Zone Type P = Partition RC = Report Code In = Input Device Type L = Loop number to which the sensor is connected. NOTE: Pressing the [C] copies the zone information from the last saved zone that includes the input type. Verify this information is correct for this zone. On this screen: Use the [B] key to move to left and to back up to “ZT” field. Press [,] to accept the existing or newly-entered zone information.

Zn ZT P RC 10 03 1 10

In L RF -

• •

Use the [A] key to move to the right.

– 15 –

PROMPT
10 INPUT S/N: A XXX-XXXX L -

EXPLANATION
If you entered RF, BR, UR or SL for the Input Type, this screen displays. Otherwise the summary screen for the next zone displays. Enter the 7-digit serial number, using one of the following methods: a. Transmit two open and close (or close and open) sequences. For a button-type transmitter, press and release the button, wait approximately 4 seconds, then press and release the button a second time. OR b. Manually enter the 7-digit serial number printed on a label on the transmitter, using the alpha keypad. Then press the [,] key, the cursor will move to the “L” position. You can edit the loop number, if necessary. When the loop number is acceptable, press [,]. OR c. Press key [C] to copy the last serial number enrolled (used when programming a transmitter with several input loops). Remember, you can use the [A] key to move to the right or the [B] key to move to the left. You can also use the [#] key to back up without saving. L 1 Press [,] to accept the serial number and advance to the “L” position (if method “a” or “c” was used), then enter the loop number. If necessary, press the [#] key to back up without saving, and re-enter or edit the serial number before pressing [,] to save The system checks for a duplicate. If a duplicate serial/loop number combination is found, the keypad will emit a single long beep, and display the serial number along with a “?” for the loop number, allowing you to re-enter the correct loop number. To Delete an Existing Serial Number, enter “0“ in the loop number field. The serial number will change to “0”s. If “0” was entered in error, simply re-enter the loop number or press [#], and the serial number will return to the display. The prompt to confirm appears. This prompt only appears if you answered “Yes” at the “SET TO CONFIRM?” prompt. The system enters a confirmation mode so that the operation of the actual programmed input can be confirmed. Activate the loop input or button that corresponds to this zone. At any time during this step, you may press the [,] key on the keypad to save the serial and loop number combination without confirming. 1 If the serial number transmitted does not match the serial number entered, a display similar to the one at the left appears. If the loop number does not match, it also is displayed. If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary display for the next zone does not appear), press the [#] key twice and then enter or transmit the correct serial number. Activate the button on the wireless key again after re-entering the serial number. If the serial number transmitted matches the serial number entered, the system beeps 3 times and advances to the summary display for the next zone's programming. After all the zones have been programmed, enter 00 for the zone number to quit.

10 INPUT S/N: A022-4064

10 INPUT S/N: A000-0000

L 1

XMIT TO CONFIRM PRESS ,TO SKIP

Entd Rcvd

A022-4063 A022-4064

Zn 11

ZT 00

P 1

RC 10

In L 00 1

– 16 –

Entering Wireless Keys If you pressed the D key previously to enter defaults for 5804 and/or 5804BD wireless keys, the following screens appear:

PROMPT
FROM TEMPLATE 1–6 1

EXPLANATION
Enter template number (1–6). 1–3 = 5804 templates; 4–6 = 5804BD templates. See the defaults provided for each template in the chart that follows these procedures. Select from templates. Press [,] to display template (template 1 shown selected). Note: If necessary, press [#] to back up and re-enter template number. Press [#] if you want to return to zone attributes screen. When you press [,], the selected template is displayed. Top line of display represents loop numbers; bottom line represents zone type. Press [,] to accept template. Enter partition number for wireless key. Press [,] to continue. The system searches for the highest available, consecutive 4-zone group (the four zones required for the 5804 and 5804BD), and displays the lowest zone number of the group. If you want to start at a different zone number, enter the zone desired and press [,]. If that zone number is displayed, the system has the required number of consecutive zones available, beginning with the zone you entered. If not, the system again displays a suggested zone that can be used. If the required number of consecutive zones is not available at all, the system will display “00.” Press [,] to accept. To enter the serial number: Press and release a button on the wireless key. OR Manually enter the 7-digit serial number printed on the device’s label. Press [,] to accept serial number. The system checks for a duplicate. If a duplicate exists, a long error beep will sound and the serial number reverts to all “X”s allowing you to re-enter the serial number. Use the [A] key to move forward within the screen, and the [B] key to back up. If you entered YES previously at the SET TO CONFIRM prompt (see first prompt following entry into the Expert Programming Mode), the display on the left appears. To confirm, activate the button on the wireless key that corresponds to this zone. If the serial number transmitted does not match the serial number entered, a display similar to the one at the left appears. If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary display does not appear), press the [#] key and then enter the correct serial number. Activate the button on the wireless key again after re-entering the serial number. If the serial number transmitted matches the serial number entered, the system will beep 3 times and revert to the "Start Zone No." prompt and will show the lowest numbered zone of the next available 4-zone group (4 consecutive zones) that is available for programming. After all the wireless keys have been entered, enter 000 for the zone number to quit.

L 01 02 03 04 ZT 23 22 21 23 1

PARTITION 1 ENTER ZONE NO 00 = QUIT 24 L Example of zone number suggested by the system. This indicates that zones 24, 25, 26, and 27 are available. 24 INPUT S/N AXXX-XXXX L 1

XMIT TO CONFIRM PRESS ,TO SKIP

Entd Rcvd

A022-4063 A022-4064

ENTER ZONE NO 00 = QUIT

– 17 –

Wireless Key Default Templates 5804
Template 1 Loop 1 2 3 4 Loop 1 2 3 4 Loop 1 2 3 4 Function No Response Disarming Arm AWAY No Response Function No Response Disarming Arm AWAY Arm STAY Function 24-Hour Panic Disarming Arm AWAY Arm STAY Zone Type 23 22 21 23 Zone Type 23 22 21 20 Zone Type 07 22 21 20

5804BD
Template 4 Loop 1 2 3 4 Loop 1 2 3 4 Loop 1 2 3 4 Function No Response No Response Arm AWAY Disarming Function No Response Arm STAY Arm AWAY Disarming Function 24-Hour Panic Arm STAY Arm AWAY Disarming Zone Type 23 23 21 22 Zone Type 23 20 21 22 Zone Type 07 20 21 22

Template 2

Template 5

Template 3

Template 6

– 18 –

Alpha Descriptors Programming
You can program a user-friendly English language description/location for all protection zones, relays, keypad panics, polling loop short, and RF receiver supervision troubles. Each description can be composed of a combination of words (up to 3) that are selected from a vocabulary of 244 words stored in memory, and any word can have an "s" or " 's " added to it. NOTE: Due to the use of 2-digit zone numbers, the first word of the descriptor is limited to 7 characters if you want it to fit on the top line of the display. In addition, up to 20 installer-defined words can be added to those already in memory. Thus, when an alarm or trouble occurs in a zone, an appropriate description for the location of that zone will be displayed at the keypad. A custom installer's message can be programmed for each partition that is displayed when the system is "Ready" (e.g., THE PETERSONS’). 1. To program alpha descriptors, enter Programming mode, then press #93 to display "ZONE PROG?" 2. Press [0] (NO) twice to display "ALPHA PROG?". 3. Press [1] to enter Alpha Programming. There are 5 submenu selections that will be displayed one at a time. Press [1] to select the mode desired. Press [0] to display the next mode available. The alpha menu selections are: ZONE DESCRIP? DEFAULT SCREEN? CUSTOM WORD? PART DESCRIP? EXIT EDIT MODE? 4. For entering zone descriptors. For creating custom message; displayed when system is ready. For creating custom words for use in descriptors. For creating 4-character partition names. Press [1] to exit back to #93 Menu Mode.

Refer to the sections that follow for procedures for adding alpha descriptors.

Zone Descriptors 1. Select ZONE DESCRIPTOR mode. The keypad keys perform the following functions: [3] Scrolls both alphabet and actual words in ascending alphabetical order. [1] Scrolls both alphabet and actual words in descending alphabetical order. [2] Adds or removes an "s" or " 's " to a vocabulary word. [6] Switches between alphabet and actual word list; used to accept entries. [8] Saves the zone description in the system's memory. [#] [#] plus zone number displays the description for that zone. 2. Enter the zone number to which you want to assign a descriptor. For example, key [,] 01 to begin entering the description for Zone 1, (key [,] 02 for Zone 2, [,] 03 for Zone 3, etc.). The following is displayed: , ZN 01 A. Note that the first letter of the alphabet appears after the zone number, and that the zone number is automatically included with the description. 3. Enter the descriptor for that zone. Use one of two methods as follows: (Assume, for example, that the desired description for Zone 1 is BACK DOOR.) a) Press [#] followed by the 3-digit number of the first word from the fixed dictionary shown later in this section (e.g., [0][1][3] for BACK). Press [6] in order to accept the word and proceed, or press [8] to store the complete descriptor and exit; or b) Select the first letter of the desired description (note that "A" is already displayed). Use the [3] key to advance through the alphabet and the [1] key to go backward. Press [3] key repeatedly until "B" appears (press [1] to go backwards if you happen to pass it), then press [6] to display the first available word beginning with “B”. Press [3] repeatedly to advance through the available words until the word “BACK” is displayed. To add an "s" or " 's," if you need to, press 2. The first depression adds an "s," the second depression adds an " 's, " the third depression displays no character (to erase the character), the fourth depression adds an "s," etc.

– 19 –

Accept the word. To accept the word, press [6], which switches back to the alphabet list for the next word, or press [8] to store the complete descriptor and then exit. Select the next word. For selection of the next word (DOOR), repeat step 3a (word #057) or 3b, but selecting the word "DOOR.” To accept the word, press [6], which again switches back to alphabet list. Store the descriptor. When all desired words have been entered, press [8] to store the description in memory. To review the zone descriptors, key [#] plus zone number (e.g., #01). To edit zone descriptors, key [,] plus zone number (e.g., ,01) Exit Zone Description Mode: enter 00.

Default Screen (Custom Message Display) Normally, when the system is in the disarmed state, the following display is present on the keypad.
****DISARMED**** READY TO ARM

The message above can be modified partially or in its entirety to create a custom installer message for each partition. For example, “****DISARMED****” on the first line or “READY TO ARM” on the second line could be replaced by the installation company name or phone number for service. Note: There are only 16 character spaces on each of the two lines. To create a custom display message, proceed as follows: 1. Select Default Screen mode. The keypad asks for the partition number for this message. Enter the partition number. Press [,] to accept entry. The following display appears:
****DISARMED**** READY TO ARM

3. 4.

A cursor is present at the extreme left of the first line (over the first "star"). Press [6] to move the cursor to the right and [4] to move the cursor to the left. Press [7] to insert spaces or erase existing characters. Create the message. For example, to replace “READY TO ARM” with the message “SERVICE 424-0177,” proceed as follows: Press [6] to move the cursor to the right, and continue until the cursor is positioned over the first location on the second line. Press [3] to advance through the alphabet to the first desired character (in this case, "S"). Press [1] to go backward, when necessary. When the desired character is reached, press [6]. The cursor then moves to the next position, ready for entry of the next character (in this example, "E"). When the cursor reaches a position over an existing character, press [3] or [1] to advance or back up from that character in the alphabet. Proceed in this manner until all characters in the message have been entered. Save the message. Store the new display message in memory by pressing [8]. The system asks for a new partition number. Enter 0 to quit or 1-8 for a new partition number.

Custom Words Up to 20 installer-defined words can be added to the built-in vocabulary. Each of the 20 "words" can actually consist of several words, but bear in mind that a maximum of 10 characters can be used for each word string. 1. Select CUSTOM WORD Mode. The keys perform the following functions: [3] Advances through alphabet in ascending order. [1] Advances through alphabet in descending order. [6] Selects desired letter; moves the cursor 1 space to the right. [4] Moves the cursor one space to the left. [7] Inserts a space at the cursor location, erasing any character at that location. [8] Saves the new word in the system's memory. [,] Returns to Description Entry Mode.

– 20 –

6. 7.

Enter the custom word number (01-20) you want to create. For example, if you are creating the first word (or word string), enter 01; when creating the second word, enter 02, and so on. A cursor now appears at the beginning of the second line. Type the word using one of two methods as follows: a) Press [#], followed by the 2-digit entry for the first letter you would like to display (e.g., 65 for "A"). When the desired character appears, press [6] to select it. The cursor will then move to the right, in position for the next character. Press [#] plus the 2-digit entry for the next letter of the word. or b) Press 3 to advance through the list of symbols, numbers, and letters. Press 1 to move back through the list. When you have reached the desired character, press [6] to select it. The cursor then moves to the right, in position for the next character. Repeat step 3 to create the desired custom word (or words). Press [4] to move the cursor to the left if necessary. Press [7] to enter a blank (or to erase an existing character). Each word or word string cannot exceed 10 characters. Save the word by pressing [8]. This returns you to the “CUSTOM WORD?” display. The custom word (or string of words) is automatically added to the built-in vocabulary at the end of the group of words beginning with the same letter. Custom words are retrieved as word numbers 250 to 269 for words 1 to 20, respectively, when using method 3a to enter alpha descriptors. When using method 3b to enter alpha descriptors, each word appears at the end of the group of words that begin with the same letter as it does. Repeat steps 2 through 6 to create up to a maximum of 20 custom words (or word strings). Exit Custom Word Mode by entering 00 at the “CUSTOM WORD” prompt.

Partition Descriptors 1. Select "Part DESCRIPT." Mode. The system asks for the partition number desired. Enter the number as a single-key entry 1-8. 2. Follow the same procedure as for custom words. Note: The partition descriptors are limited to 4 characters (e.g., WHSE for warehouse).

– 21 –

Alpha Descriptor Vocabulary
(For entering alpha descriptors. To select a word, press [#] followed by the word's 3-digit number.) NOTE: This vocabulary is not to be used for relay voice descriptors. See the Relay Voice Descriptors section when programming relay voice descriptors.
000 (Word Space) • 001 AIR • 002 ALARM 003 ALCOVE 004 ALLEY 005 AMBUSH • 006 AREA • 007 APARTMENT 008 ART • 009 ATTIC 010 AUDIO 011 AUXILIARY • 012 BABY • 013 BACK • 014 BAR 015 BARN • 016 BASEMENT • 017 BATHROOM • 018 BED • 019 BEDROOM 020 BELL • 021 BLOWER • 022 BOILER 023 BOTTOM 024 BOX 025 BREAK • 026 BUILDING 027 BURNER 028 • 029 030 031 032 033 034 035 036 • 037 038 039 • 040 041 042 043 044 045 • 046 047 • 048 049 • 050 051 CABINET CALL CAMERA CAR CASE CASH CCTV CEILING CELLAR CENTRAL CIRCUIT CLIP CLOSED COIN COLD COATROOM COLLECTION COMBUSTION COMPUTER CONTACT DAUGHTERS DELAYED DEN DESK • 052 DETECTOR • 053 DINING 054 DISCRIMINATOR 055 DISPLAY 056 DOCK • 057 DOOR 058 DORMER • 059 DOWN • 060 DOWNSTAIRS 061 DRAWER • 062 DRIVEWAY 063 DRUG • 064 DUCT • 065 066 067 068 • 069 070 • 071 072 • 073 074 075 • 076 • 077 078 • 079 • 080 081 082 • 083 084 • 085 086 087 EAST ELECTRIC EMERGENCY ENTRY EQUIPMENT EXECUTIVE EXIT EXTERIOR FACTORY FAILURE FAMILY FATHERS FENCE FILE FIRE FLOOR FLOW FOIL FOYER FREEZER FRONT FUR FURNACE 102 INTERIOR 103 INTRUSION 104 JEWELRY • 105 KITCHEN • 106 LAUNDRY • 107 LEFT 108 LEVEL • 109 LIBRARY • 110 LIGHT 111 LINE 112 LIQUOR • 113 LIVING • 114 LOADING 115 LOCK 116 LOOP 117 LOW • 118 LOWER • 119 120 121 122 • 123 124 • 125 126 127 128 129 • 130 • 131 132 133 MACHINE MAGNETIC MAIDS MAIN MASTER MAT MEDICAL MEDICINE MICROWAVE MONEY MONITOR MOTHERS MOTION MOTOR MUD 151 POLICE 152 POOL • 153 POWER 154 QUAD 155 • 156 157 158 159 160 • 161 • 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 RADIO REAR RECREATION REFRIG REFRIGERATION RF RIGHT ROOM ROOF SAFE SCREEN SENSOR SERVICE SHED SHOCK SHOP SHORT SHOW SIDE SKYLIGHT SLIDING SMOKE SONIC SONS SOUTH SPRINKLER STAMP STATION STEREO STORE STORAGE STORY STRESS STRIKE SUMP SUPERVISED SUPERVISION SWIMMING SWITCH TAMPER TAPE TELCO TELEPHONE TELLER TEMPERATURE THERMOSTAT TOOL • • • • 202 TRANSMITTER 203 TRAP 204 205 206 207 208 209 210 211 212 ULTRA UP UPPER UPSTAIRS UTILITY VALVE VAULT VIBRATION VOLTAGE WALL WAREHOUSE WASH WEST WINDOW WINE WING WIRELESS WORK

• • • • • • • • •

213 214 215 • 216 • 217 218 • 219 220 221

222 XMITTER 223 YARD 224 ZONE (No.) • 225 ZONE 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 250 to 269 0 1 1ST 2 2ND 3 3RD 4 4TH 5 5TH 6 6TH 7 7TH 8 8TH 9 9TH Custom Word 1 Custom Word 20

• 134 NORTH 135 NURSERY • 136 137 • 138 139 • 140 141 142 143 • 144 145 • 146 147 • 148 149 150 OFFICE OIL OPEN OPENING OUTSIDE OVERFLOW OVERHEAD PAINTING PANIC PASSIVE PATIO PERIMETER PHONE PHOTO POINT

088 GALLERY • 089 GARAGE • 090 GAS 091 GATE • 092 GLASS 093 GUEST 094 GUN • 095 HALL • 096 HEAT 097 HIGH 098 HOLDUP 099 HOUSE 100 INFRARED • 101 INSIDE

194 195 196 197 198 • 199 200 • 201

CHARACTER (ASCII) CHART
32 33 34 35 36 37 38 39 40 41 (space) ! " # $ % & ' ( ) 42 43 44 45 46 47 48 49 50 51 * + , . / 0 1 2 3 52 53 54 55 56 57 58 59 60 61 (For Adding Custom Words) 4 62 > 5 63 ? 6 64 @ 7 65 A 8 66 B 9 67 C : 68 D ; 69 E < 70 F = 71 G 72 73 74 75 76 77 78 79 80 81 H I J K L M N O P Q 82 83 84 85 86 87 88 89 90 R S T U V W X Y Z

Notes: This factory-provided vocabulary of words is subject to change. Bulleted words in bold face type are those that are also available for use by the 4286 VIP Module. If you are using a VIP Module, and words other than these are selected for alpha descriptors, the Voice Module will not provide annunciation of those words. – 22 –

Device Programming
This menu is used to program keypads, receivers, and relay modules, etc. Device Address 00 is always set as an alpha keypad assigned to Partition 1 with no sounder suppression options, and these settings cannot be changed. From Data Field Programming mode, press #93 to display "ZONE PROG?" Press [0] repeatedly to display "DEVICE PROG?"

PROMPT
DEVICE PROG? 1=YES 0=NO DEVICE ADDRESS 01-30, 00=QUIT

EXPLANATION
Press [1] to enter Device Programming. 0 The device address identifies the device to the control. Enter the 2-digit device address number to match the device's physical address setting (01-30). Press [,] to accept entry.

DEVICE TYPE 00

Select the type of addressable device as follows: 00 = device not used 01 = alpha keypad (6160) 02 = fixed-word keypad (6150) Press [,] to accept entry. 03 = RF receiver (5881) 04 = output relay module (4204) 05 = voice (VIP) Module (4286)

Alpha or Fixed-Word Keypad

PROMPT
01 CONSOLE PART. 1

EXPLANATION
If you selected device type 01 (alpha keypad), or 02 (fixed-word keypad), this prompt appears. Enter the addressable device's default partition number (01 to maximum number of partitions programmed for system in field 2*00). This is the primary partition for the device. Enter 9 to make this keypad a "Master" keypad for the system. Press [,] to accept entry. Keypads can be individually programmed to suppress arm/disarm beeps, entry/exit beeps and chime mode beeps. This helps prevent unwanted sounds from disturbing users in other areas of the premises. Enter a number 00-03 for the keypad sounding suppression options desired for the keypad as follows: 00 = no suppression 01 = suppress arm/disarm & entry/exit beeps 02 = suppress chime mode beeps only 03 = suppress arm/disarm, entry/exit and chime mode beeps Press [,] to accept entry.

01 SOUND OPTION 00

RF Expander

PROMPT
01 RF EXPANDER HOUSE ID

EXPLANATION
If you selected device type 03 (RF receiver), this prompt appears. Enter the 2-digit House ID (00-31). This is required if you are using a wireless keypad or bi-directional device (5827, 5804BD, etc.). Press [,] to accept entry.

VIP Module

PROMPT
01 MODULE PART. 1

EXPLANATION
If you selected device type 05 (VIP Module) this prompt appears. Enter the partition number 1-8 in which the module is located. Press [,] to accept entry. Press 00 + [,] to exit Menu mode. Press ,99 to exit Program mode.

– 23 –

Relay Programming
The system supports up to 16 relays. Relays can be used to perform many different functions and actions. Each output must be programmed to begin one of three types of ACTIONS at a designated START event, and end that ACTION at a designated STOP event. The options used to start and stop these devices are described below, followed by the actual screen prompts and available entries. The letter(s) in parentheses after each function described below, such as (A) after ACTION, are those that appear in the various summary displays of programmed data during programming. ACTION (A) The "ACTION" of the device is how the device will respond when it is activated by the "START" programming. You may want the device to activate momentarily, to pulse on and off continuously, or to remain activated until some other event occurs to stop it. There are five different action choices: • ACTIVATE for 2 SECONDS and then reset. • ACTIVATE and REMAIN ACTIVATED until stopped by some other event. • PULSE ON and OFF until stopped by some other event (do not use with an FSA device). • NO RESPONSE when the device is not used. START (STT) The "START" programming determines when and under what conditions the device is activated. The following START options are available: 1) EVENT (EV) is the condition (alarm, fault, trouble) that must occur to a zone or group of zones (zone list) in order to activate the device. These conditions apply only when a zone list is used. The different choices for "EVENT" are listed below and in “Programming Relays” later in this section. • ALARM Action begins upon any alarm in an assigned zone in the zone list. • FAULT Action begins upon any opening of an assigned zone in the zone list. • TROUBLE Action begins upon any trouble condition in an assigned zone in the zone list. • NOT USED Action is not dependent upon one of the above events. ZONE LIST (ZL) is a group of zones to which the “EVENT” applies in order to activate a particular device. Note that there are a total of 8 zone lists that can be programmed; when the selected EVENT (alarm, fault or trouble) occurs in any zone in the selected “Start” ZONE LIST (1-8), activation of the selected device will START. 2) ZONE TYPE/SYSTEM OPERATION (ZT). If all zones to be used to start the device have the same response type, and there are no other zones of this type that are not to activate this device, then “ZONE TYPE” may be used instead of a "ZONE LIST" and "EVENT” to activate the device. If a system operation, such as “DISARMING” or “ANY FIRE ALARM,” is to activate the device, enter the appropriate choice under the “ZONE TYPE” option. The “ZONE TYPE/SYSTEM OPERATION” option functions independently of the “EVENT/ZONE LIST” combination. If a specific "ZONE TYPE" is chosen, any zone of that response type going into alarm, trouble, or fault will cause the device to activate as selected in "ACTION.” If the same “ZONE TYPE” is also chosen for the STOP programming, any zone of that type that restores will de-activate the device. If a "SYSTEM OPERATION" is chosen, that operation will cause the device to activate as selected in "ACTION.” The different choices for "ZONE TYPE" and "SYSTEM OPERATION" are listed in “Programming Relays” later in this section, and on the Programming Form. 3) PARTITION NO. (P). The device's "Start" ZONE TYPE/SYSTEM OPERATION may be limited to an occurrence on one partition (1-8), or any partition (0). STOP (STP): The "STOP" programming determines when and under what conditions the device is de-activated. The following options are available: 1). RESTORE ZONE LIST (ZL). If a "ZONE LIST" is used as the “Stop” event, the device de-activates when all the zones in that list restore from a previous fault, trouble, or alarm condition. This occurs regardless of what is programmed to "START" the device; therefore, a "RESTORE ZONE LIST" is normally only used when a "ZONE LIST" is used to start the device. 2). ZONE TYPE/SYSTEM OPERATION (ZT). Instead of using a "RESTORE ZONE LIST," you can select a specific zone (response) type or system operation action to de-activate the device. If you choose a specific "ZONE TYPE," any zone of that response type that restores from a previous alarm, trouble, or fault condition will cause the device to de-activate. If you choose a "SYSTEM OPERATION," that operation causes the device to de-activate. The different choices for "ZONE TYPE" and "SYSTEM OPERATION" are listed in “Programming Relays” later in this section, and in the Programming Form. 3) PARTITION NO. (P). The device's "Stop" Zone Type/System Operation may be limited to an occurrence on one partition (1-8), or on any partition (0). The “ZONE TYPE/SYSTEM OPERATION” option functions independently of the “RESTORE/ZONE LIST” combination. – 24 –

Relay Devices Programming From Data Field Programming Mode, press #93 to display the "ZONE PROG?" prompt. Press [0] (NO) to each menu option until the "RELAY PGM?" prompt appears. Press [1] (YES). While in this mode, press [,] to advance to next screen. Press [#] to back up to the previous screen.

PROMPT
ENTER RELAY # (00=QUIT) 01

EXPLANATION
Enter the relay (output device) identification number 01-16. This is a reference number only, used for identification purposes. The actual module address and relay number on the module are programmed in the last two prompts. Press [,] to continue. Press [,] to continue.

02 A EV ZL ZT P STT 0 0 00 00 0 02 STOP A ZL ZT P 0 00 00 0

The keypad displays a summary STOP screen. Press [,] to continue. The Relay Action is the way in which the relay will respond when activated by the "start" event. Enter the desired action for this relay as follows: 0=not used; 1=close for 2 seconds.; 2=stay closed; 3=pulse on/off An output may be activated by an Event/Zone List combination, and/or by a Zone Type/System Operation. For an Event/Zone List combination, enter the event code as follows: 0=not used; 1=alarm; 2=fault; 3=trouble If you are not using a Zone List to activate the relay, enter 0. Press [,] to continue. A zone list is a set of zones that can be used to initiate the start or stop relay action. If a zone list is being used to start this relay action, enter the zone list number, 1-8. If a zone list is not being used, enter 0. Press [,] to continue. A Zone Type/System Operation can be used instead of or in addition to an Event/Zone List combination or a specific zone to start the relay action. If a Zone Type/System Operation is being used, enter the 2-digit code as listed in the table that follows. Press [,] to continue.

02 RELAY ACTION NO RESPONSE

02 START EVENT NOT USED

02 START: ZN LIST 0

02 START: ZN TYPE NO RESPONSE 00

Choices for Start/Stop Zone Types and System Operations:
00 = No Response (Not Used) 23 = No Alarm Response 01 = Entry/Exit #1 31 = End of Exit Time 02 = Entry/exit #2 32 = Start of Entry Time 03 = Perimeter 33 = Any Burglary Alarm 04 = Interior Follower 34 = Code + [#] + 71 Key Entry 05 = Trouble Day/Alarm Night 35 = Code + [#] + 72 Key Entry 06 = 24-Hr. Silent 36 = At Bell Timeout ** 07 = 24-Hr. Audible 37 = 2 Times Bell Timeout ** 08 = 24-Hr. Auxiliary 38 = Chime 09 = Fire Alarm or Trouble 39 = Fire Alarm 10 = Interior W/Delay 40 = Bypassing 20 = Arming-STAY*** 41 = AC Power Fail 21 = Arming-AWAY**** 42 = System Battery Low 22 = Disarming (Code + Off) * Stop condition only ** Or at disarming, whichever occurs earlier *** The output also activates when the partition is armed in the INSTANT mode **** The output also activates when the partition is armed in the MAXIMUM mode 43 = Communication failure 44 = RF Low Battery 45 = Polling Loop Failure 51 = RF Receiver Failure 52 = Kissoff 54 = Fire Zone Reset 55 = Disarm + 1 Minute 56 = XX Minutes (enter XX in field 1*74) * 57 = YY Seconds (enter YY in field 1*75) * 58 = Duress 60 = Audio Alarm Verification (must be selected for both START and STOP operation)

If you are using options 56 and/or 57 (usually as the STOP Zone Type), you must program data fields 1*74 and 1*75 for the respective relay timeouts for minutes and seconds.

– 25 –

PROMPT
02 START: PARTN ANY PARTITION

EXPLANATION
If the starting event will be limited to occurring on a specific partition, enter the partition number (1-8) in which the start event will occur. Enter 0 for any partition. Press [,] to continue.

Do not use a zone programmed with an RF Button (Input Type BR) to STOP a relay. The system will not deactivate the relay.

PROMPT
02 STOP: ZN LIST 0 02 STOP: ZN TYPE NO RESPONSE 00 02 STOP: PARTN ANY PARTITION

EXPLANATION
If a zone list is being used to stop this relay action, enter the zone list number, 1-8. The restore of a zone on the zone list stops the relay. If a zone list is not being used, enter 0. Press [,] to continue. If a Zone Type/System Operation is being used to stop the relay action, enter the 2-digit code listed in the Choices for Start/Stop System Operation chart. Press [,] to continue. This is the partition to which the stop condition will be limited. Enter 0 for any partition. Enter 1-8 for specific partition number. Press [,] to continue. Relays may be grouped for common activation by time-driven events (commands 06-10). Enter 0 (no group) or 1-8 for a specific group number. Press [,] to continue. The system may have some devices that are not intended to be under end user control, such as relays activating fire doors or machinery. Enter 1 if the end user will be restricted from accessing this relay group. Press [,] to continue. Enter 1 for (ECP) relay modules (4204). Enter 2 for X-10 devices. Press [,] to continue. If you selected 1 (4204), enter the actual module's address (01-15) as set by its DIP switches. Press [,] to continue. Enter the specific relay number on that module (1-4). Press [,] to continue. The keypad will display the Start and Stop summary screens again. Press [,] to continue. If you selected 2 for X-10 devices, enter the numerical equivalent of the House Code of the device, as follows: A=00 D=03 G=06 J=09 M=12 P=15 B=01 E=04 H=07 K=10 N=13 C=02 F=05 I=08 L=11 O=14 Enter the numerical unit code of the X-10 device (00-15). Press [,] to continue. The keypad displays the Start and Stop summary screens again. Press [,] to continue.

02 RELAY GROUP 0

02 RESTRICTION 1=YES 0=NO

02 RELAY TYPE ECP 02 ECP ADDRESS

00 02 MODULE RELAY# 0

02 HOUSE CODE A

02 UNIT CODE 00

When all relays have been programmed, enter 00 at the "ENTER RELAY NO." prompt. If you are defining a zone list, continue to the next section. If not, enter 00 + [,] at the next two prompts. You will then be asked "Quit Menu Mode?" Enter 1 for "Yes," 0 for "No." Then enter ,99 to exit programming completely.

– 26 –

Zone List Programming After all relays have been programmed, upon entering 00 at the "ENTER RELAY NO." prompt, you are asked to enter a zone list. If a zone list number was used to start or stop a relay, you must define the zones belonging to that list as follows:

PROMPT
ENTER Zn LIST ? 0=QUIT 01 ADD ZONE # 00=QUIT

EXPLANATION
Enter the zone list number 1-8. Enter 0 to quit. 0 Using 2-digit entries enter each zone to be included in this zone list. Press [,] after you enter each zone number. When you have entered all zones, enter 00. Press [,] to continue. Enter 0 to save this zone list. Enter 1 to delete it. 0 Enter 1 to delete one or more zones in that zone list. Enter 0 if no changes are necessary. If you enter 1, the following screen appears; otherwise, the "Enter Zone LIST" prompt reappears. Enter each zone number to be deleted from the zone list, pressing [,] after each number.

01 Del Zn LIST ? 1=YES 0=NO 01 DEL ZONES ? 1=YES 0=NO

01 Zn to DELETE ? 00=QUIT 00

VIEW Zn LIST ? 0=QUIT

This display appears if you pressed 0 at the “Enter Zone LIST” prompt. Enter the zone list number that you wish to view. Press [,] to continue. Press [,] to scroll through all zones in that list. Enter 00 +[,] to quit. Press [1] to exit Menu Mode. Press ,99 to exit Program Mode.

01 ASSIGNED ZONE 00=QUIT 00

Relay Voice Descriptors
If you are using the 4286 VIP Module, voice descriptors can be programmed for the 16 outputs. These descriptors are announced by the voice module when you access the relays via the # 70 Relay Access Mode over the telephone. Each voice descriptor can consist of up to 3 words selected from the Relay Voice Descriptors and Custom Word Substitutes Vocabulary list (later in this section). The index numbers from this vocabulary list are to be used for relay voice descriptors only. For normal system voice annunciation (e.g., alarms, troubles, status), use the highlighted words in the alpha vocabulary list in the Alpha Programming part of this guide. To enter relay voice descriptors, do the following: 1. From Data Field Programming mode, press #93 to display the "ZONE PROG?" prompt. 2. Press [0] (NO) to each menu option until the "RLY VOICE DESCR?" prompt is displayed. Follow the instructions below. While in this mode, press [,] to advance to next screen. Press [#] to back up to previous screen.

PROMPT
RLY VOICE DESCR? 1=YES 0=NO ENTER RELAY NO. 00=QUIT 01

EXPLANATION
Press [1] to program voice descriptors for relays. 0 Enter the 2-digit relay number (01-32) for the relay desired, or enter 00 to quit Relay Voice Descriptor Programming Mode. Press [,] From the Relay Voice Descriptors and Custom Word Substitutes Vocabulary list, enter the 3-digit index number for the first word of the relay descriptor phrase. Press [,] to accept entry.

01 ENTER DESC d1

– 27 –

PROMPT
01 ENTER DESC d2

EXPLANATION
From the Relay Voice Descriptors and Custom Word Substitutes Vocabulary list, enter the 3-digit index number for the second word of the relay descriptor phrase. If second word is not desired, press [000]. Press [,] to accept entry. From the Relay Voice Descriptors and Custom Word Substitutes Vocabulary list, enter the 3-digit index number for the third word of the relay descriptor phrase. If third word is not desired, press [000]. Press [,] to accept entry. The “ENTER RELAY NO.” prompt appears. Enter the next relay number to be programmed. When you have programmed all output devices, enter 00 to quit. Enter ,99 to exit Program Mode.

01 ENTER DESC d3

Relay Voice Descriptors and Custom Word Substitutes Vocabulary
Word Index Air ............................ 116 Alarm ....................... 255 And .......................... 067 Apartment ................ 117 Appliances ............... 161 Area ......................... 118 Attic.......................... 119 Baby......................... 120 Back......................... 121 Bar ........................... 122 Basement................. 021 Bathroom ................. 051 Battery ..................... 053 Bed .......................... 092 Bedroom .................. 015 Blower...................... 123 Boiler........................ 124 Bright ....................... 162 Building .................... 125 Burglary ................... 039 Call .......................... 009 Central ..................... 089 Chime ...................... 054 Closed...................... 126 Computer ................. 127 Console.................... 066 Word Index Daughter's ................208 Den...........................052 Detector....................128 Device ......................060 Dim...........................163 Dining .......................031 Door .........................016 Down ........................008 Downstairs................184 Driveway...................130 Duct..........................131 East ..........................132 Eight .........................077 Eighth .......................221 Equipment ................133 Exit ...........................004 Factory .....................134 Father's ....................211 Fence .......................135 Fifth ..........................218 Fire ...........................040 First .........................136 Five ..........................074 Floor .........................029 Four..........................073 Fourth .......................217 Foyer ........................137 Word Index Front ........................ 087 Garage ..................... 023 Gas .......................... 138 Glass........................ 139 Hall........................... 050 Heat ......................... 010 Inside ....................... 209 Kitchen ..................... 022 Laundry .................... 140 Left........................... 027 Library ...................... 141 Light ......................... 019 Living ....................... 030 Loading .................... 142 Lower ....................... 094 Machine ................... 143 Master...................... 144 Medical..................... 014 Mother's ................... 212 Motion ...................... 145 Nine ......................... 078 Ninth ........................ 222 Word Index No.............................165 North.........................146 Not............................012 Off ............................011 Office ........................147 On ............................058 One...........................070 Open.........................148 Outside .....................210 Panic ........................013 Partition ....................090 Patio .........................149 Phone .......................061 Power .......................063 Pump ........................166 Rear .........................088 Right .........................028 Room........................018 's...............................007 Second .....................056 Service .....................150 Seven .......................076 Seventh ....................220 Shed .........................151 Shop .........................152 Word Index Side.......................... 153 Six............................ 075 Sixth ......................... 219 Smoke...................... 024 Son's ........................ 223 South........................ 155 Stairs........................ 006 Station...................... 156 Storage .................... 157 Sun .......................... 154 System ..................... 062 Temperature............. 158 Third......................... 159 Three........................ 072 Tool.......................... 213 Two .......................... 071 Up ............................ 025 Upper ....................... 187 Upstairs.................... 183 Utility ........................ 185 West......................... 215 Window .................... 017 Wing......................... 216 Zero ......................... 069 Zone......................... 002

– 28 –

Custom Word Substitutes for VIP Module Annunciation
A substitute word can be programmed for each of the 20 custom words used in your alpha zone descriptions. The VIP Module announces this substitute word in place of the custom word that is displayed on the alpha keypad. For example, an alarm display of "John's Bedroom" could be announced as "Son's Bedroom," as there is no annunciation for the custom word "John." Note that if a substitute word is not assigned, the VIP Module will not annunciate the zone descriptor at all, but will only annunciate the zone number. To enter custom word substitutes, do the following: 1. From Data Field Programming Mode, press #93 to display the "ZONE PROG?" prompt. 2. Press [0] (NO) to each menu option until the "CUSTOM INDEX ?" prompt is displayed.

PROMPT
CUSTOM INDEX ? 1=YES 0=NO CUSTOM WORD NO. 00=QUIT

EXPLANATION
Enter [1] at this prompt. 0 Enter the custom word number (01-20) for which a voice substitute is desired. Enter 00 to quit this Programming Mode. Press [,] to accept entry. Enter the 3-digit substitute word index number from the Relay Voice Descriptors and Custom Word Substitutes Vocabulary list in the Relay Voice Descriptors part of this section. Press [,] to accept entry. The "CUSTOM WORD NO." prompt is displayed. Enter the next custom word number to be substituted, or enter 00 to quit.

01 ENTER INDEX #

– 29 –

System Layout Worksheets
Before programming any security system, you should first define the installation. To help you lay out a partitioned system, use the following worksheets. This will further simplify the programming process. PARTITIONS
Partition # Descriptor (4-char max) Prim. Sub. # Sec. Sub. # Alpha Default Message (32-character maximum)

Partition 1 Partition 2 Partition 3 Partition 4 Partition 5 Partition 6 Partition 7 Partition 8 Keyswitch Arming Partition Assignment (1-8): Wireless Keypad Partition Assignment (1-8): Voice Module Partition Assignment (1-8): Use Partition Descriptor (yes/no)? Common Lobby Partition Assignment (1-8):

COMMUNICATION OPTIONS BY PARTITION
Option Swinger Suppression Count 00-15; 00=no suppression Cancel Report After Disarm Dialer Reports for Panic (* + 1) Dialer Reports for Panic (# + 3) Dialer Reports for Panic (* + #) Dialer Reports for Duress Burglary Alarm Communications Delay (16 sec.) Part. 1 Part. 2 Part. 3 Part. 4 Part. 5 Part. 6 Part. 7 Part. 8

SYSTEM DEFINITIONS BY PARTITION (enter values or yes/no)
Option Part. 1 Part. 2 Part. 3 Part. 4 Part. 5 Part. 6 Part. 7 Part. 8 Entry Delay #1 (00, 30-225 seconds): Exit Delay #1 (00, 45-225 seconds): Entry Delay #2 (00, 30-225 seconds): Exit Delay #2 (00, 45-225 seconds): Quick Arming Multiple Alarms per Arming Console Panic for Zone 95 (* + 1) Console Panic for Zone 96 (# + 3) Console Panic for Zone 99 (* + #) Allow Sign-on (GOTO function) Non-Bypassable Zone* Sounder Timeout Duration for Bell (2 min. increments) Console Annunciation During Entry** Console Annunciation During Exit Confirmation of Arming Ding for Bell Chime on Bell Access Control Relay (field 1*76) Affects Lobby (check partitions that apply) Arms Lobby (check partitions that apply) *Can be any zone 01-86. **no= 3 beeps yes=continuous

– 30 –

PRINTER OPTIONS
12- or 24-hour Time format Printer On-Line (yes/no) 1200 or 300 baud Printer Baud Rate Option Alarm Trouble Bypass Open/Close System

EVENT LOG TYPES
No Yes

DEVICES (keypads, 4204, rf receivers, vip module)
Addr 00. 01. 02. 03. 04. 05. 06. 07. 08. 09. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. Type Part Sound Opt House ID Device Types: 00 = Device Not Used 01 = Alpha Keypad 02 = Fixed-Word Keypad 03 = RF Receiver 04 = Output Relay Module 05 = Voice Module NOTE: Address 04 must be used for the Voice Module, if used. Console Sounder Options: 0 = No Suppression 1 = Suppress Arm/Disarm and Entry/Exit Beeps 2 = Suppress Chime Mode Beeps Only 3 = Suppress Arm/Disarm, Entry/Exit and Chime Mode Beeps

ACCESS CODES & USER DEFINITIONS FOR PARTITIONS 1 & 2
4-digit Security Code Access Group 0; 1-8 2-Digit User # Auth. Level Partition 1 Open/ Close RF Key Global Arm 2-Digit User # Auth. Level Partition 2 Open/ Close RF Key Global Arm

– 31 –

ACCESS CODES & USER DEFINITIONS FOR PARTITIONS 3 & 4
4-digit Security Code Access Group 0; 1-8 2-Digit User # Auth. Level Partition 3 Open/ Close RF Key Global Arm 2-Digit User # Auth. Level Partition 4 Open/ Close RF Key Global Arm

ACCESS CODES & USER DEFINITIONS FOR PARTITIONS 5 & 6
4-digit Security Code Access Group 0; 1-8 2-Digit User # Auth. Level Partition 5 Open/ Close RF Key Global Arm 2-Digit User # Auth. Level Partition 6 Open/ Close RF Key Global Arm

ACCESS CODES & USER DEFINITIONS FOR PARTITIONS 7 & 8
4-digit Security Code Access Group 0; 1-8 2-Digit User # Auth. Level Partition 7 Open/ Close RF Key Global Arm 2-Digit User # Auth. Level Partition 8 Open/ Close RF Key Global Arm

Authority Levels: 1=Master (arm, disarm, bypass, and/or modify lower level users) 2=Manager (arm, disarm, bypass, and/or modify lower level users) 3=Operator A (arm, disarm, bypass) 4=Operator B (arm, disarm) 5=Operator C (arm, disarm only if system was armed with this code) 6=Duress code (arm, disarm, triggers silent panic alarm)

— 32 —

ZONE DEFINITION FOR ZONES 01-25
Part 1-8 Input Type Serial # / Loop Rpt. Code Zone Information (part numbers) & Alpha Descriptor (3 words max.)

Zone No.

Zone Type

— 33 —

ZONE DEFINITION FOR ZONES 26-50
Part 1-8 Input Type Serial # / Loop Rpt. Code Zone Information (part numbers) & Alpha Descriptor (3 words max.)

Zone No.

Zone Type

— 34 —

ZONE DEFINITION FOR ZONES 51-75
Part 1-8 Input Type Serial # / Loop Rpt. Code Zone Information (part numbers) & Alpha Descriptor (3 words max.)

Zone No.

Zone Type

— 35 —

ZONE DEFINITION FOR ZONES 76-86
Part 1-8 Input Type Serial # / Loop Rpt. Code Zone Information (part numbers) & Alpha Descriptor (3 words max.)

Zone No.

Zone Type

— 36 —

ZONE DEFINITIONS FOR KEYPAD PANIC ZONES 95, 96, & 99
Enter yes/no for each partition-field *22 Zone No. Zone Type 1 2 3 4 5 6 7 8 Report Code Zone Information (part numbers) & Alpha Descriptor (3 words max.)

95 96 99

ZONE DEFINITIONS FOR SYSTEM ZONES; 88; 89, 90, 91, 97 & 98
Zone No. Zone Type Report Code Zone Information (part numbers) & Alpha Descriptor (3 words max.)

88 89 90 91 97 98

Zone Types: 00=zone not used 01=entry/exit 1 02=entry/exit 2 03=perimeter 04=interior (follower) 05=day/night burglary 06=24-hour silent 07=24-hour audible 08=24-hour auxiliary 09=supervised fire Input Types: 00=not used 01=hardwired 03=supervised RF transmitter 04=unsupervised RF transmitter 05=RF button transmitter 06=serial number polling loop 07=Dip switch-type polling loop 08=right loop dip switch polling loop 10=interior (delay) 20=arm stay 21=arm away 22=disarm 23=no alarm response

— 37 —

Relay Devices Worksheets
Applicable only if relays (4204), or X-10 devices are used.
Relays are programmed in the #93 Menu Mode in the Relay Programming Section. Fill in the required data on the worksheet below and follow the procedure in the Installation and Setup Guide as you enter the data during the displays and prompts that appear in sequence. Notes: 1. For 4204 the Device Programming section must be programmed for the device address. Set the DIP switches on the device for that address. 2. For X-10 devices, use the 1361X10 transformer in place of the transformer that comes in the box with the control panel.
OUTPUT DEV # S T A R T A EV/ZL ZT / P S T O P ZL ZT / P Relay Group Restrict 1=4204 2=X-10 Dev Add 4204 or House Code for X-10 Relay # for 4204 or Unit Code for X-10

1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. A = EV = ZL = DEVICE ACTION EVENT ZONE LIST 0 = No Response; 1 = Close for 2 sec; 2 = Close and stay closed; 3 = Pulse on and off 0 = Not used; 1 = Alarm; 2 = Fault; 3 = Trouble; 4 = Restore 1-8, 0 = Not Used "START" ZONE LIST: Upon alarm, fault, trouble or restore of ANY zone in this list, device action will START. "STOP" ZONE LIST: Upon restore of ALL zones on this list, device action will STOP. It need not be same list as used for START.

— 38 —

ZT =

ZONE TYPE/SYSTEM OPERATION

Choices for Start/Stop Zone Types and System Operations:
00 = No Response (Not Used) 23 = No Alarm Response 43 = Communication failure 01 = Entry/Exit #1 31 = End of Exit Time 44 = RF Low Battery 02 = Entry/exit #2 32 = Start of Entry Time 45 = Polling Loop Failure 03 = Perimeter 33 = Any Burglary Alarm 51 = RF Receiver Failure 04 = Interior Follower 34 = Code + [#] + 71 Key Entry 52 = Kissoff 05 = Trouble Day/Alarm Night 35 = Code + [#] + 72 Key Entry 54 = Fire Zone Reset 06 = 24-Hr. Silent 36 = At Bell Timeout ** 55 = Disarm + 1 Minute 07 = 24-Hr. Audible 37 = 2 Times Bell Timeout ** 56 = XX Minutes (enter XX in field 1*74) * 08 = 24-Hr. Auxiliary 38 = Chime 57 = YY Seconds (enter YY in field 1*75) * 09 = Fire Alarm or Trouble 39 = Fire Alarm 58 = Duress 10 = Interior W/Delay 40 = Bypassing 60 = Audio Alarm Verification (must be 20 = Arming-STAY*** 41 = AC Power Fail selected for both START and STOP operation) 21 = Arming-AWAY**** 42 = System Battery Low 22 = Disarming (Code + Off) NOTE: Any zone in "ZT" for Start, going into alarm, fault, or trouble will activate the relay. Any zone in "ZT" for Stop, that restores will stop the relay action. * Stop condition only ** Or at Disarming, whichever occurs earlier *** The output also activates when the partition is armed in the INSTANT mode **** The output also activates when the partition is armed in the MAXIMUM mode

PARTITION No. 1-8, 0 = Any

ZONE LISTS FOR OUTPUT DEVICES – Programmed in the #93 Menu Mode in the Output Programming Section. Fill in the required data on the worksheet below and follow the procedure shown earlier in this Programming Guide as you enter the data during the displays and prompts that appear in sequence. Up to 8 zone lists may be created Note: Record desired zone numbers below. More or fewer boxes than shown may be needed, as any list may include any or all of system's zone numbers. Zone List 1: Started or stopped by zone numbers (enter 00 to end entries).

Zone List 2: Started or stopped by zone numbers (enter 000 to end entries).

Zone List 3: Started or stopped by zone numbers (enter 000 to end entries).

Zone List 4: Started or stopped by zone numbers (enter 000 to end entries).

Zone List 5: Started or stopped by zone numbers (enter 00 to end entries).

Zone List 6: Started or stopped by zone numbers (enter 000 to end entries).

— 39 —

Zone List 7: Started or stopped by zone numbers (enter 000 to end entries).

Zone List 8: Started or stopped by zone numbers (enter 000 to end entries).

Scheduling Menu Prompts
To program schedules, enter Scheduling program mode by pressing [User Code] + # + 80 to display the first choice of the menu driven programming functions. NOTE: Only users with an Installer or Master level user code may enter the #80 mode. Press 0 (NO) or 1 (YES) in response to the displayed menu selection. Pressing 0 will display the next choice in sequence. Menu selections are as follows:

PROMPT
Time Window ? 1 = YES 0 = NO O/C Schedules ? 1 = YES 0 = NO Holidays ? 1 = YES 0 = NO Timed Events ? 1 = YES 0 = NO

EXPLANATION
For defining up to 20 time windows each with a start and a stop time programmed by entering the hours and minutes. For defining the daily open and close schedules for the 8 partitions. Each partition can be programmed with an opening and closing window for each day of the week and holidays. For defining up to 16 holidays for which partitions they apply. 0 For defining up to 20 time driven events with the following parameters: • Time window • Action desired • Action specifier • Activation time • Days of the week For defining the limitation of access schedules for the user codes. Each schedule can be programmed with two window for each day of the week and holidays

Access Sched. ? 1 = YES 0 = NO

#80 & #81 MENU MODE KEY COMMANDS The following is a list of commands used while in the Menu mode.
#80 or #81 [,] [#] 0 1 01-09 00 Enters Menu mode Serves as ENTER key. Press to have keypad accept entry. Backs up to previous screen. Press to answer NO. Press to answer YES. All data entries are either 2-digit entries. Exits Menu mode, returns to normal operation mode when entered at the first question for each category.

— 40 —

Scheduling Worksheets
Time Windows Definitions Worksheet. The system provides 20 time windows that are defined with start and stop times. They are programmed in the #80 Menu Mode. Fill in the required data on the worksheet below and follow the procedure in the installation instructions as you enter the data during the displays and prompts that appear in sequence. Time Window Start Time Stop Time Number (HH:MM) (HH:MM) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 (Keep this worksheet handy, as you will be asked for a given time window number later in this section).

Because the time windows are shared among all partitions, it is important to make sure that changing a time window does not adversely affect desired actions in other partitions. Daily Open/Close Schedule Worksheet: Using the time windows previously defined, fill in the required data on the worksheet below and follow the procedure in the installation instructions as you enter the data during the displays and prompts that appear in sequence. Part 1 2 3 4 5 6 7 8 Mon Op Cl Tues Op Cl Wed Op Cl Thur Op Cl Fri Op Cl Sat Op Cl Sun Op Cl Hol Op Cl

— 41 —

Holiday Schedule Worksheet: The system provides up to 16 holidays that can be assigned for the system. Each holiday can be assigned to any combination of partitions. Fill in the required data on the worksheet below and follow the procedure in the installation instructions as you enter the data during the displays and prompts that appear in sequence. HOL Month/Day 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 / / / / / / / / / / / / / / / / 1 2 Partition 3 4 5 6 7 8

Time-Driven Event Worksheet: The system provides up to 20 time-driven events that can be programmed for the system. Fill in the required data on the worksheet below and follow the procedure in the installation instructions as you enter the data during the displays and prompts that appear in sequence. Sched Num. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Time Window Day(s) M T W T F S S H Action Desired Action Specifier Activation Time

— 42 —

Below is a list of the "Action" codes (desired actions) used when programming time-driven events. Note that these codes are independent of the "relay codes" programmed during the #93 Menu Mode–Relay Programming mode. If using Time Driven Events, the following menu items must first be programmed using #93 Menu Mode - Relay Programming: Enter Relay No. (reference identification number) Relay Group (if applicable) Restriction Relay Type (4204 or X-10) ECP Address Relay No. House Code Unit Code (4204) (4204) (X-10) (X-10)

Relay commands: Action Specifier for commands 01-05 is Relay No.; Action Specifier for commands 06-10 is Relay Group No. 01 = Relay On 02 = Relay Off 03 = Relay Close for 2 seconds 04 = Relay Close XX minutes (field 1*74) 05 = Relay Close YY seconds (field 1*75) 06 = Relay Group On 07 = Relay Group Off 08 = Relay Group Close for 2 seconds 09 = Relay Group Close XX minutes (field 1*74) 10 = Relay Group Close YY seconds (field 1*75) Arm/Disarm commands: Action Specifier for commands 20-24 is Partition(s). Activation times 1 (Beginning), 2 (End), 3 (During) are the only valid choices for auto-arming and disarming functions. 20 = Arm-Stay 21 = Arm Away 22 = Disarm 23 = Force Arm Stay (Auto-bypass faulted zns) 24 = Force Arm Away (Auto-bypass faulted zns) Bypass commands: Action Specifier for commands 30-31 is Zone List #, Activation times 1 (Beginning), 2 (End), 3 (During) are the only valid choices for bypass commands. 30 = Auto bypass - Zone list 31 = Auto unbypass - Zone list Open/Close Windows: Action Specifier for commands 40-41 is Partition(s), and for 42 is Access Group. Activation time 3 (During) is the only valid choice for these commands. 40 = Enable Opening Window 41 = Enable Closing Window 42 = Enable Access Window Activation time: Refers to when the action is to take place relative to the time window. 1 = Beginning of time window 2 = End of time window 3 = During time window active period only (On at beginning of window, off at end). 4 = Beginning and end of time window Limitation of Access Worksheet The system provides up to 8 Access Schedules that can be programmed for the system. Fill in the required data on the worksheet below and follow the procedure in the installation instructions as you enter the data during the displays and prompts that appear in sequence. Acc Sch 1 2 3 4 5 6 7 8 Mon W1 W2 Tues W1 W2 Wed W1 W2 Thurs W1 W2 W1 Fri W2 Sat W1 W2 Sun W1 W2 Hol W1 W2

— 43 —

Temporary Schedule #81 Menu Mode. The system provides a Temporary Schedule for each partition. Enter the temporary scheduling mode by pressing [Installer Code] + [#] + [81]. Fill in the required data on the worksheet below and follow the procedure in the installation instructions as you enter the data during the displays and prompts that appear in sequence. Partition/Windows 1 Disarm Window Start Time Stop Time HH:MM HH:MM Mon Tue Wed Thu Fri Sat Sun

Arm Window Start Time Stop Time 2 HH:MM HH:MM

Disarm Window Start Time Stop Time HH:MM HH:MM

Arm Window Start Time Stop Time 3 HH:MM HH:MM

Disarm Window Start Time Stop Time HH:MM HH:MM

Arm Window Start Time Stop Time 4 HH:MM HH:MM

Disarm Window Start Time Stop Time HH:MM HH:MM

Arm Window Start Time Stop Time 5 HH:MM HH:MM

Disarm Window Start Time Stop Time HH:MM HH:MM

Arm Window Start Time Stop Time 6 HH:MM HH:MM

Disarm Window Start Time Stop Time HH:MM HH:MM

Arm Window Start Time Stop Time HH:MM HH:MM — 44 —

Partition/Windows 7 Disarm Window Start Time Stop Time HH:MM HH:MM

Mon

Tue

Wed

Thu

Fri

Sat

Sun

Arm Window Start Time Stop Time 8 HH:MM HH:MM

Disarm Window Start Time Stop Time HH:MM HH:MM

Arm Window Start Time Stop Time HH:MM HH:MM

— 45 —

WARNING: OWNER'S INSTRUCTION NOTICE NOT TO BE REMOVED

WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM.

NOTES:

Blue Jumper (note 5)

BATTERY TABS
Red Jumper (note 1)
ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 ZONE 9

4. Zone 8 supports 2-wire latching type glass break detectors. 1. Zone 1 may be selected for EOLR supervised See Installation and Setup Guide for recommended type or normally closed (no EOLR) operation via and maximum number of detectors supported. cut jumper. (Cut red jumper for normally closed operation. Do not cut for Fire Usage). Zones 2-8 5. Cut blue jumper to disable supervision of alarm sounder output. may be selected for either operation via program Leave jumper intact to supervise output. (See Installation and field *41. Setup Guide for Programming and Wiring Instructions). 2. Zone 1 supports 2-wire smoke detectors. See Installation and Setup Guide for recommended type and maximum number of detectors supported.

RED (+)

Connect to 12VDC, 4AH - 17.2AH SEALED LED ACID BATTERY

3. Zone 7 may be used for remote keyswitch arming/disarming. See Installation and Setup Guide for wiring instructions.

J7 Header J8 Header MAKE CONNECTIONS USING No. 4142TR CABLE Optional programming: 1. I n 2 (Printer DTR) 1. Not Used Out 1: Open/close or keypad-like sounding 2. Ground 2. GroundOut 2: Armed LED 3. Out 1 (Ground Start) 3. In 3 (1361X10 sync) Out 4: Ready LED 4. In 4 (1361X10 sync) 4. GroundJ8 Ratings for Out 1: 5. Ground 5. Out 2 (fire) 6. Out 5 (1361X10 data) Active: 10VDC-13.8VDC through 4k OHMS 6. Ground1 2 3 4 5 6 7 8 9 7. Out 6 (Printer RXD) Not Active: 100 OHMS to ground 7. Out 3 (burg/aud. panic) Ratings for out 2-4: 8. Ground 8. Ground Active: 10VDC-13.8VDC through 5k OHMS 9. Ground 9. Out 4 (silent panic/ Not Active: 1k OHMS to ground J7 duress) (Refer to Installation Instructions for information concerning Direct Wire 1 2 3 4 5 6 7 8 9 Downloading and printer connections using the 4100SM Serial Module.)

1
ZONE 1

29
(G TIP RE EN ) RI (R NG ED )

BLK (–)

(B TIP RO WN ) R (G ING RA Y)

+ – + –
N.C. N.C. N.C.

EARTH GROUND Connect to good earth ground to maintain immunity to transients. See Instructions for proper grounding.
DOC LOAD NO.: 5

+ –

Data in

Data out

+ –
N.C. Blk
N.O. N.O. N.O. N.O.

Handset

Incoming Phone Line

NO CONNECTION

POLLING LOOP

See Installation Instructions for max. # of keypads and for max. wire run length. 2k EOLR (note 1)
2k EOLR (note 1,3)

2k EOLR (note 1)

2-WIRE SMOKE DETECTOR LOOP (Also supports NO/NC Burg contacts)

VISTA-50P/VISTA-50PUL Summary of Connections Diagram

— 46 —
+
GLASS BREAK

LATCHING TYPE GLASS BREAK DETECTOR LOOP

BELL

–

Programmable Response (Fast/Normal) Loop

CHARGING VOLTAGE 13.7VDC See Installation Instructions for required capacity Connect to 24hr. 120VAC, Replace 60 Hz Outlet every 3 years

Red
REMOTE KEYPAD/DEVICES (Addressable keypads) only

Grn

Yel

Telephone connections using Ademco No. 620 RJ31X direct connect cord.

WARNING: TO PREVENT RISK OF ELECTRICAL SHOCK, DISCONNECT TELCO JACK BEFORE SERVICING THIS PANEL.

+
4208U

TRANSFORMER 16.5VAC, 40VA ADEMCO No.1361 (IN CANADA USE No. 1361CN) OR 1361X10 IF X-10 DEVICES WILL BE USED

+ –
SMOKE

+ – +
Fire Usage

–
N.C. N.C.

+ –

N.C.
N.O. Burg. Usage N.O. N.O.

N.C.

5193SD SMOKE

NOTE: WHEN POWERING UP THE PANEL, PLUG THE TRANSFORMER IN BEFORE CONNECTING THE BATTERY.

SIREN N.C. 2k EOLR (note 1) 2k EOLR (note 1)

AUXILARY POWER OUTPUT 9.6VDC - 13.8VDC, 750mA maximum Note: Include current drawn by keypads and polling loop devices when making auxiliary power calculations.

ALARM SOUNDER OUTPUT 10VDC - 13.8VDC, 1.7A max

N.C. 2k EOLR (note 1,4)

4190 SN

N.O. 2k EOLR (note 1,2)

THIS EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION'S STANDARD 72, CHAPTER 2 (NATIONAL FIRE PROTECTION ASSOC., BATTERYMARCH PARK. QUINCY, MA. 02169). PRINTED INFORMATION DESCRIBING PROPER INSTALLATION, OPERATION, TESTING, MAINTENANCE, EVACUATION PLANNING AND REPAIR SERVICE IS TO BE PROVIDED WITH THIS EQUIPMENT.
USE LIMITED-ENERGY CABLE FOR ALL CONNECTIONS

For Household Fire Installations, supervise alarm sounder output (Note 5) and limit combined alarm sounder, aux power and polling loop current to 750mA.

ALL CIRCUITS ARE POWER LIMITED

Zone resistance (Excluding EOLR): ZONE 1,8: 100 OHMS MAXIMUM ALL OTHER ZONES: 300 OHMS MAXIMUM Zone response time: ZONES 1-8: 350mSec-500mSec ZONE 9: Programmable for Fast: 10mSec-15mSec Normal: 350mSec-500mSec (default response)

Polling loop rating: 64mA max. See Installation Instructions for maximum number of devices supported and maximum wire run length.
CONNECTION OF THE FIRE ALARM SIGNAL TO A FIRE ALARM HEADQUARTERS OR A CENTRAL STATION SHALL BE PERMITED ONLY WITH THE APPROVAL OF THE LOCAL AUTHORITY HAVING JURISDICTION. THE BURGLAR ALARM SIGNAL SHALL NOT BE CONNECTED TO A POLICE EMERGENCY NUMBER.

COMPLIES WITH FCC RULES, PART 68 FCC REGISTRATION NO. AC398U-68192-AL-E RINGER EQUIVALENCE: 0.7B THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

VISTA-50P/VISTA-50PUL SUMMARY OF CONNECTIONS

V50P_PUL-SOC-V2

— 47 —

ÊVISTA50PÊVISTA50P-PRV22Š
VISTA50P-PRV2 5/04 Rev. B

Uploaded: September 17, 2012