Honeywell VISTA GSM Installation manual

K14733V2 5/09 Rev. A

VISTAVISTAVISTA-GSM / VISTA-GSMCN
Installation Guide
General Information
The VISTA-GSM (USA) and VISTA-GSMCN (Canada) are optional communication modules intended for use with the VISTA-21iP control, and provide cellular radio communication with the AlarmNet network for delivery of alarm and other messages to the monitoring central station. These instructions describe the installation of both models. IMPORTANT! (1) The VISTA-GSM (USA) device requires activation of its SIM card. See the SIM Activation Note on page 4 for the procedure. (2) Use of this module requires an AlarmNet-I account. If an account for the control does not yet exist, please obtain the account information from the central station prior to programming this module.

PlugPlug-in GSM Module Kit

This kit contains the following components:
TRANSMIT PRIMARY POWER: 9 - 16.5 VAC CURRENT: 900mA PEAK, 70mA STANDBY BATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP
FOR EXTERNAL ANTENNA 50 OHM MMCX ONLY FCC:XXXXXXXXXX IC: YYYYYYYYYY

7720P PROGRAMMER PORT NOT FOR TELEPHONE SERVICE USE!

IMPORTANT! Disconnect power from the control, including the battery, BEFORE installing the VISTA-GSM module. CAUTION: ESD SENSITIVE DEVICE. To discharge any static buildup, briefly touch a chassis ground point before installing this module. Avoid performing this installation while standing on a carpeted floor.

Installing the VISTA-GSM module
1. Mount the VISTA-GSM Board.
a. Snap the antenna adapter cable’s plug into the VISTA-GSM board connector. b. Push the three standoffs into the appropriate holes on the VISTA-21iP control board until they snap into place. c. Carefully align the VISTA-GSM board over the standoffs and the mating connector, then, one at a time, gently push down on the board near each standoff until it snaps into place and the connector is fully seated.
MATING CONNECTOR
P B FC C A R IM R TT A ID E R Y

VISTA-21iP CONTROL BOARD
V21iP-004-V0

RX

M S GS PP B E 2 1 G E D E W O D M O SI M S R

TX

MODE 2 MODE 1 GSM GPRS WEB

RSSI

ANTENNA

ANTENNA ADAPTER PLATE

VISTA-GSM MODULE WASHER AND NUT STAND-OFFS (3)

ANTENNA ADAPTER CABLE

V21iP-009-V1

VISTA-GSM MODULE
R E X T E M R , N A M L M A C N X T O E

F O 5 0 O H
E T R IC V O R P E R S E E M N M O A H R P G E O L E R T P R P 0 O 2 F 7 7 T O N O

N

N L Y

N A

M

:G

Y

A

IP

: 6V C

P

W

C

M

. 3.

E

LA

56

1

R

A

:9

H

-

B

r

16

E

IC

FO

.5

L

H

:Y

R

V

26

24 -

A

C

E

R

7W

H

r

! E S U

B

E

M

A

C

C

56

K

U

P

H o n e y w e ll

STANDOFFS (3)

2. Install the Antenna Adapter Plate.
a. Punch out the large wiring hole knockout and the adjacent smaller knockout from the cabinet’s upperright topside. b. Position the antenna adapter plate over the large knockout, aligning the plate’s pin with the smaller knockout and push until the adapter snaps into place. c. Remove the nut and washer from the antenna adapter cable, then secure the cable’s SMA connector to the adapter plate with the washer and nut as shown.
ANTENNA ADAPTER PLATE ANTENNA

NUT WASHER LARGE WIRING HOLE KNOCKOUT

3. Install the Antenna.
The antenna mounts directly onto the antenna adapter cable at the antenna adapter plate. Carefully align the antenna’s connector over the SMA connector protruding from the adapter plate, then screw it down (clockwise) until it is finger tight. Do not over tighten.

OPTIONAL 5800 SERIES RECEIVER

ANTENNA ADAPTER CABLE

VISTA-GSM MODULE

VISTA-21iP CONTROL BOARD

Signal Strength (RSSI)
Signal strength is a measure of how well the VISTA-GSM is receiving the cell tower., Signal strength can viewed at the RSSI LEDs on the control board† (should be minimum of three RSSI LEDs lit) or can be viewed as a dBm measurement on the touchpad display by using the diagnostic shift-E command (D key followed by the 5 key) while in ∗29 Menu mode-Diagnostic mode. An acceptable dBm level is -89dBm (see dBm note at right). † NOTE: The RSSI LEDs on the control board normally display signal strength after the SIM has been activated (see note on page 4). If the SIM is not activated, signal strength can be viewed at these LEDs by simultaneously pressing and holding the TEST and STATUS switches on the control board. The following are tips for maximizing signal strength: • The best RSSI can usually be found on an exterior wall at the highest point in the building. Avoid the basement. • Maintain at least 12 inches clearance between antenna and steel I-beams, HVAC ducts, metal studs, steel roofs, exterior walls with metalized insulation or aluminum siding and other large metal objects. If a consistent RSSI of three bars cannot be found, the control cabinet may have to be moved to an area of better reception.
VISTA-GSM RADIO MODULE

ON MINIMUM LIT

RED YEL YEL GRN GRN GRN

GSM MODULE PCB CONNECTOR

dBm NOTE: dBm is displayed as a negative value on the touchpad display (diagnostic command shift-E); a smaller negative number is better. i.e., -60 dBm is a better RSSI than -100 dBm. Three RSSI LEDs lit = about -89dBm

–2–

GPRS

RSSI IBS M1 M0

V21iP-010-V0

V21iP-006-V0

GSM Status LEDs
There are three GSM Status LEDs used to indicate message and device status: • STATUS, green • MESSAGE, yellow • FAULT, red Each LED can have four different states - ON, OFF, FAST BLINK and SLOW BLINK.
COLOR/LED Green Status

GSM Status LED Meanings
DESCRIPTION On – module NOT registered Off – module is registered Fast Blink – Download session with Compass in progress Slow Blink – In unison with yellow LED – Registration in progress. On – Message transmission pending. Quick Periodic Blink – Normal. Fast Blink – Message waiting for network ACK. Slow Blink – In unison with green LED – Registration in progress. On – No contact with network. Off– Normal. Slow Blink – Loss of contact with panel (ECP fault). Fast Blink – No network contact AND loss of contact with the panel. Fast Blink – In unison with the RSSI Bar Graph LEDs – Hardware Error. Call the AlarmNet Technical Assistance Center. Indication on = signal strength (RSSI) display off = status display off = module operating in ECPmode web connection status GPRS service availability network carrier registration status

Yellow Message

Signal Strength (RSSI) and Status LEDs
The Signal Strength (RSSI) Mode and Status LEDs normally display the module’s signal strength (after SIM activation). LED 1 (top red LED) will be lit to indicate that the display is in RSSI mode, and the other LEDs indicate signal strength (lowest to highest, from top to bottom) between the module and the receiving tower. (If the SIM is not activated, simultaneously press and hold the TEST and STATUS switches on the control board to display signal strength.) Signal strength should be within 3-5 RSSI LEDs lit. Status Indicator Switch Press and hold the Status LED Indicator Switch to change the LED functions to view the network carrier status. When the switch is held down, LED 1 (top red LED) will be off, and the other LEDs have the following meanings (see diagram for specific functions):
Red Fault

All

Signal Strength and Status LED Meanings
Color Red Yel (2) Green Green Green Label RSSI mode Web GPRS GSM

VISTA-21iP CONTROL BOARD
RJ45 CONNECTOR
IP (WEB) NETWORK LEDs
GRN GRN YEL

MAC ID LABEL

ETHERNET LINK/ACTIVITY (ON=YES; OFF=NO) LINK SPEED (ON=100 MB/S; OFF=10 MB/S) NETWORK COLLISION (BLINK=DETECTED; OFF= NORMAL)

SIGNAL STRENGTH AND STATUS LEDs ON OFF IP/GSM STATUS LEDs STATUS GRN MESSAGE YEL FAULT RED ON = RSSI RSSI MINIMUM LIT RED YEL YEL GRN GRN GRN RSSI MODE 1 MODE 2 WEB GPRS GSM

TRANSMIT

INTERNAL IP/GSM JUMPER

VISTA-GSM MODULE
STATUS LED INDICATIONS SLOW BLINK

IP/GSM SWITCHES

GRN LEDs
WEB

OFF
NO WEB CONNECTION
††

BLINK

FLASH

ON
CONNECTED TO WEB

TEST STATUS LED INDICATOR

GPRS

NO GPRS SERVICE MODULE NOT REGISTERED REGISTERED LOW RSSI
†

GPRS IN USE REGISTERED ACCEPTABLE RSSI
†

GPRS SERVICE AVAILABLE
†

GSM

REGISTERED EXCELLENT RSSI

REGISTERED NO 2nd SITE AVAILABLE

† REGISTERED w/ NETWORK CARRIER AND 2nd SITE AVAILABLE † † IF NO GPRS, MESSAGE SENT VIA SMS AC 1 AC 2 BELL GND AUX 3 4 5 GRN YEL 6 7 Z1+ 8 Z19 GND 10 Z2 11 Z3 12 GND 13 Z4 14 Z5 15 GND 16 Z6 17 Z7 18 GND 19 Z8 20 TIP 21 RING TIP RING GND 22 23 24 25

V21iP-007-V2

Signal Strength and Status LED locations – Status LED Functions Table

Programming the VISTA-GSM Module
The VISTA-GSM module’s parameters are programmed using the control’s *29 Menu mode. The programming procedure can be found in the control’s Programming Guide. To program the module, press ∗29 while in Programming mode, then follow the prompts.

–3–

Registering the Control with AlarmNet
Normally, registration with AlarmNet is done at the time the control is installed. If the VISTA-GSM module is being installed as an add-on, the control must be re-registered. Follow the registration procedure in the control’s Installation and Setup Guide. A summary of registration steps follows. Register the control by using one of these methods: By phone 1. Call 1-800-222-6525 You will need the following information: • MAC ID and MAC CRC number (found on the label on control’s PC board). • Subscriber information (provided by the central station), including a city code, CSID, and a subscriber ID. • Activation ID (AID) and AID CRC numbers (found on the label on the VISTA-GSM module or on its carton) 2. When instructed to do so, triple-click the Test switch to complete the registration. Alpha Keypad using *29 Menu mode 1. Enter *29 Menu mode, select Diagnostic mode, then use the [↑] shift-B command (D key followed by the B key). The registration message is sent (“Registering” displayed) and the control waits for the acknowledgment. 2. “Registration SUCCESS” displayed, indicating successful registration. Test Switch on control’s PCB (triple-click) 1. Click the switch three times. 2. Watch the GSM Status LEDs: The Message (yellow) LED and the Status (green) LED will blink slowly in unison while registration is in progress. 3. When registration is complete, the Status (green) LED goes out. AlarmNet Direct website See paragraph at right.

VISTA-GSM SIM ACTIVATION NOTE FOR USA: The VISTA-GSM device is not activated as shipped from the factory (indicated by unlit RSSI LEDs), and must be activated and registered before it can be used. SIM activation is automatic upon successful registration. To register/activate the unit, the control in which it is used must be connected to the Internet via its Ethernet connection or the SIM must be activated using the AID number if no internet connectivity is available. After the module is installed and the control is powered up, use any of the registration methods to register the control. Upon successful registration/SIM activation, the RSSI LEDs light based on signal strength. For Canadian installations, the VISTA-GSMCN includes an activated SIM, but the module must be registered with AlarmNet before it can be used. Refer to the Registering the Control with AlarmNet section for registration procedures.

Registering through AlarmNet Direct Website To register via AlarmNet Direct Website, please go to:
https://services.alarmnet.com/AlarmNetDirect/userlogin.aspx.

Log in and follow the on-screen prompts. Please have the following information available: • Primary City ID (two-digit number provided by central station) • Primary Central Station ID (two-digit hexadecimal number provided by central station) • Primary Subscriber ID (four-digit number provided by central station) • MAC ID and MAC CRC number (located on outside of box and on label on control’s PC board) • AID and AID CRC numbers (found on the label on the VISTA-GSM module or on its carton). If you are not signed up for this service, click on “Dealer Signup” from the login screen to gain access to the Honeywell web-based programming. Dealer Sign-Up Direct Link:
https://services.alarmnet.com/AlarmNetDirectP_Sign-Up.

You will be instructed how to proceed upon completing the sign-up form. Only one sign-up per dealer is required. Once an initial user is established, additional logins may be created by that user. Once the control is registered, you may log out of the AlarmNet Direct website.

ANTENNA SPECIFICATIONS
Type: Bands: Polarization: Gain (Peak): Dual band, dipole, PCB 824-896 MHz 1850-1990 MHz Vertical 0 - 4 dBi VSWR: Impedance: Dimensions: Connector Type: <2:1 50 Ohms 185 x 26 mm SMA male

ÊK14733V2BŠ
K14733V2 5/09 Rev A

2 Corporate Center Drive, Melville, NY 11747
Copyright © 2007 Honeywell International Inc. www.honeywell.com/security