Honeywell's VISTA-21iP and VISTA-21iPSIA User Guide

ADEMCO VISTA SERIES

VISTA-21iP / VISTA-21iPSIA

Security Systems User Guide

K14490V1 7/10 Rev. A

IMPORTANT!
PROPER INTRUSION PROTECTION
For proper intrusion coverage, sensors should be located at every possible point of entry to a home or commercial premises. This would include any skylights that may be present, and the upper windows in a multi-level building. In addition, we recommend that radio backup be used in a security system so that alarm signals can still be sent to the Central Monitoring Station in the event that the telephone lines are out of order (alarm signals are normally sent over the phone lines).

EARLY WARNING FIRE DETECTION
Early warning fire detection is important in a home. Smoke and heat detectors have played a key role in reducing fire deaths in the United States. With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's National Fire Alarm Code (NFPA 72). These recommendations can be found on page 47 of this manual. SYSTEM COMPATIBILITY NOTICE Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell for use with your security system. Your Honeywell security system is not designed for use with any device that may be attached to your security system's keypad or other communicating bus if Honeywell has not approved such device for use with your security system. Use of any such unauthorized device may cause damage or compromise the performance of your security system and affect the validity of your Honeywell limited warranty. When you purchase devices that have been manufactured or approved by Honeywell, you acquire the assurance that these devices have been thoroughly tested to ensure optimum performance when used with your Honeywell security system.

About This Manual
This manual is a step-by-step guide that will acquaint you with the system's features and benefits. It defines the components and their functions, describes their operation, and provides clear step-by-step instructions for normal and emergency procedures. Keep this manual in a convenient place so that you can refer to it as necessary.

–2–

Table of Contents
System Overview ...................................................................................................................................... 5 Introduction ....................................................................................................................................... 5 System Basics .................................................................................................................................... 5 Using the Voice Message Center ...................................................................................................... 7 About The Keypads .................................................................................................................................. 8 General Information.......................................................................................................................... 8 Fixed-Word Display Keypad ........................................................................................................... 10 Functions of the Keypads ....................................................................................................................... 11 Entry/Exit Delays ................................................................................................................................... 14 Entry Delay...................................................................................................................................... 14 Exit Delay ........................................................................................................................................ 14 Exit Alarms...................................................................................................................................... 15 Checking For Open Zones ...................................................................................................................... 16 Using the [∗] Key to Display and Announce System Status.......................................................... 16 Arming the System ................................................................................................................................. 17 STAY Mode: Arms Perimeter Only, Entry Delay On .................................................................... 17 NIGHT-STAY Mode: Arms Perimeter Only, Plus Selected Zones ................................................ 17 INSTANT Mode: Arms Perimeter Only, Entry Delay Off ............................................................. 17 AWAY Mode: Arms Entire System, Entry Delay On..................................................................... 17 MAXIMUM Mode: Arms Entire System, Entry Delay Off ............................................................ 17 Arming Commands.......................................................................................................................... 18 Single Button Arming ..................................................................................................................... 19 Single Button “Step” Arming .......................................................................................................... 19 Keyswitch................................................................................................................................................ 20 Using the Keyswitch ....................................................................................................................... 20 Disarming and Silencing Alarms........................................................................................................... 21 Using the [OFF] key ........................................................................................................................ 21 Bypassing Protection Zones ................................................................................................................... 22 Using the BYPASS Key................................................................................................................... 22 Quick Bypass ................................................................................................................................... 23 Chime Mode ............................................................................................................................................ 24 Using the Chime Mode.................................................................................................................... 24 Using the Voice Chime .................................................................................................................... 24 Date and Time ........................................................................................................................................ 25 Viewing the Current Date and Time .............................................................................................. 25 Setting the Date and Time.............................................................................................................. 25 Panic Keys............................................................................................................................................... 26 Using Panic Keys............................................................................................................................. 26

–3–

Table of Contents (continued)
Macro Key Programming & Usage ........................................................................................................ 27 About Macro Keys ........................................................................................................................... 27 Example of Macro Programming .................................................................................................... 28 Using a Programmed Macro Key .................................................................................................... 28 Using Device Commands........................................................................................................................ 29 Paging Feature ....................................................................................................................................... 30 About Automatic Paging ................................................................................................................. 30 About Manual Paging...................................................................................................................... 31 Latch Key Paging ............................................................................................................................ 31 Security Codes & Authority Levels........................................................................................................ 32 About Security Codes ...................................................................................................................... 32 Authority Level Definitions ............................................................................................................ 32 How to Assign User Codes and Attributes ..................................................................................... 33 Accessing Other Partitions..................................................................................................................... 34 About Accessing Partitions ............................................................................................................. 34 Using the GoTo Command .............................................................................................................. 35 Multi-Partition Arming ................................................................................................................... 35 Common Zone Operation................................................................................................................. 36 Scheduling............................................................................................................................................... 37 About Scheduling............................................................................................................................. 37 Creating Schedules.......................................................................................................................... 37 Event Logging Procedures...................................................................................................................... 39 About Event Logging....................................................................................................................... 39 Viewing the Event Log .................................................................................................................... 39 Testing the System ................................................................................................................................. 41 Trouble Conditions ................................................................................................................................. 42 Maintaining Your System ...................................................................................................................... 45 Fire Alarm System ................................................................................................................................. 46 Quick Guide to Basic System Functions................................................................................................ 50 Summary of Audible/Visual Notifications ............................................................................................. 51 Regulatory Statements and Warnings .................................................................................................. 53 System Features ..................................................................................................................................... 55 User Setup ....................................................................................................................................... 56 Paging Setup.................................................................................................................................... 57 List of Output Devices..................................................................................................................... 58 Owner’s Insurance Premium Credit Request........................................................................................ 59 Limitations Of This System ................................................................................................................... 63 Warranty................................................................................................................................................. 64

–4–

System Overview
Introduction
Congratulations on your ownership of a Honeywell Security System. You've made a wise decision in choosing it, for it represents the latest in security protection technology today. This system provides: • Three forms of protection: burglary, fire* and emergency • At least one keypad which provides control of system and displays system status • Various sensors for perimeter and interior burglary protection • Smoke or combustion detectors* designed to provide early warning in case of fire. Your system may also have been programmed to automatically send alarm or status messages to a Central Monitoring Station. * Commercial installations and some residential systems may not include fire protection – check with your installer. NOTE: Features and procedures described in this manual apply to the VISTA-21iP/VISTA-21iPSIA security systems. Differences are noted where applicable.

System Basics
Burglary Protection • Several modes of burglary protection: Stay, Night-Stay, Away, Instant, Maximum. STAY: arms perimeter zones only and entry delay is on INSTANT: same as STAY, except entry delay is off NIGHT-STAY: arms perimeter zones and selected interior zones; entry delay on AWAY: arms perimeter and all interior zones, entry delay is on MAXIMUM: same as AWAY, except entry delay is off • You can BYPASS selected zones while leaving the rest of the system armed. • CHIME mode alerts you to the opening of protected doors and windows while the system is disarmed. Fire Protection and Carbon Monoxide Protection • Fire and carbon monoxide protection is always active (if installed) and an alarm sounds if a fire or carbon monoxide condition is detected. • If necessary, you can manually initiate a fire alarm using the keypad (if programmed). • Refer to the Fire Alarm System section for information regarding fire protection, carbon monoxide protection, smoke detectors and planning emergency exit routes. Security Codes • You were assigned a 4-digit security code (master code) during installation. • Use your security code when arming and disarming the system, and when performing other system functions. • Other users can be assigned different security codes, each with different authority levels, which define the system functions a particular user can perform.

–5–

System Overview (cont’d)
Zones and Partitions • The system sensing devices have been assigned to various “zones,” which are specific areas of protection (e.g., front door, kitchen window, etc.). • Zone numbers are displayed at the keypad when an alarm or trouble condition occurs on a sensor. • Partitions provide two independent areas of protection, with each partition containing a group of zones that can be armed and disarmed without affecting other zones or users. • Partitioned systems can include a common zone area, which is an area shared by users of both partitions (such as a lobby in a building). Arming, Step-Arming and Disarming Burglary Protection • The system must be armed before the burglary protection can sense intrusions. • To arm your system, enter your user code followed by the desired arming key. • If programmed, you can press the [#] key in place of your security code when arming the system (e.g., instead of entering your 4-digit security code + [3-STAY] to arm the system in STAY mode, you can press [#] + [3-STAY]). • You can also use the step-arming feature if programmed, to arm the system. This is a function key that allows you to arm the system in one of three modes by simply pressing the key repeatedly. • To disarm the system, enter your security code then press the [OFF] key. Alarms • When an alarm occurs, both the keypad and external sounders sound, and the keypad displays the zone(s) causing the alarm. For most alarms, the external sounder also sounds. • If your system is connected to a Central Monitoring Station, an alarm message is also sent. (Delayed Reporting Note: Message reporting is delayed 30 seconds by default to reduce false alarms. If desired, this delay can be removed or can be increased to 45 seconds. See your installer if you want the delay time changed.) • To stop the alarm sounding, simply disarm the system. Memory of Alarm • When an alarm condition occurs, the keypad displays the number(s) of the zone(s) that caused the problem, and displays the type of alarm. • The message remains displayed even after disarming the system, but can be cleared with another “off” sequence. Phone Access • If included, a phone module permits you to access the system via a touch-tone phone, either on-premises or by call-in when away. • When you call in, the phone module announces system status over the telephone, and you can arm/disarm the system and perform most function commands remotely using the telephone keys. • Complete information for using these features is provided with the voice module.

–6–

System Overview (cont’d)
Function Keys • The “A,” “B,” “C,” and “D” keys can be programmed to perform various functions. • Functions include: activate a panic alarm, arm the system, provide step arming, switch lights on/off, send a message to a pager, display Time/Date, and start a programmed Macro sequence. Paging Feature • If programmed, the system can automatically send certain system condition messages to up to four pagers. • The pager displays code numbers identifying the type of condition that has occurred. Scheduling • Your system can be programmed to automatically perform certain functions (e.g., arm the system) at a predetermined time each day.

Using the Voice Message Center (if Voice Keypad is installed)
Voice keypads feature a voice message center that lets you record and playback one message. • The message can be up to 2.5-minutes long • The message remains in memory until a new message is recorded. • The volume control is adjustable. • Refer to the procedures below when using the Message Center functions.
SPEAKER LCD DISPLAY

ARMED

1 4 7

OFF

2 5 8 0

AWAY

3 6 9 #

STAY

RECORD

VOLUME
TEST

PLAY
BYPASS

LEDs

READY

MAX

MESSAGE

INSTANT

CODE

CHIME

MIC

READY

STATUS

VOICE

FUNCTION

MICROPHONE

FUNCTION KEYS

Message Center Functions
To… record a message end recording play a message adjust the volume Press these keys…
# FUNCTION 1 OFF RECORD # FUNCTION # + + 0 VOICE 0 + + 3 STAY PLAY 2 AWAY , then press Adjusting message volume also adjusts status volume. Volume cannot be adjusted while playing. The recorded message plays and the red MESSAGE LED turns off. + 0 VOICE + 1 OFF RECORD

Notes…
The red MESSAGE LED lights. Message remains in memory until a new message is recorded. The red MESSAGE LED flashes, indicating message waiting.

FUNCTION VOICE VOLUME volume key [3] ↑ (up) or [6] ↓ (down)

–7–

6160V-003-V0

About The Keypads
General Information
Your keypads allow you to control all system functions and feature the following: • A telephone style (digital) keypad • Liquid Crystal Displays (LCD) that show the nature and location of all occurrences • Built-in sounder that sounds during alarms and troubles. The sounder also "beeps" during certain system functions and also when depressing any of the keys (to acknowledge the key press). • Backlighting of the LCD display windows. Backlighting turns on when any key is pressed or when entering the premises through any assigned entry/exit door. This feature is helpful when a keypad is located in a dimly lit area. • Some keypads have a voice feature that announces the nature and location of all system occurrences. Voice keypads also announce any faulted entry/exit or perimeter zone when Chime mode is on. Ask your installer if this option has been programmed for your system.
IMPORTANT: If the keypad beeps rapidly upon entering the premises, it indicates that an alarm has occurred during your absence and an intruder may still be on the premises. LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location.

Your keypads are functionally the same, but may have different types of displays, depending on the type installed with your system. Alpha Display 2-line alpha display keypads feature a 2-line, 32-character alphanumeric LCD that displays system messages in friendly English. These keypads can also be programmed with custom zone descriptors. Fixed-Word display keypads are functionally identical to Alpha display keypads, but the LCD display uses predesignated words to identify the nature and location of occurrences. Voice Keypads (if installed), are functionally the same as other keypads, except that these keypads can provide the following: • Voice announcements of system status (see Checking for Open Zones section) • Voice chime, which can alert you to the opening of doors and windows while the system is disarmed (see Voice Chime in Chime mode section) • Message center, which lets you record and playback messages (see Using the Voice Message Center in the System Overview section).

Fixed-Word Display

Voice Keypads

–8–

About The Keypads (cont’d)

ARMED

1 4

OFF

2 AWAY 5
TEST

3

STAY

ARMED

1 4 7

OFF

2 5 8 0

AWAY

3 6 9 #

STAY

READY

MAX

6 BYPASS 9 CHIME #
6150-00-001-V0

READY

MAX

TEST

BYPASS

7 INSTANT
READY

8 CODE 0

INSTANT

CODE

CHIME

READY

Standard Fixed-Word Display Keypad

Standard Alpha Display Keypad

ARMED

1 4 7

OFF

2 5 8 0

AWAY

3 6 9 #

STAY

RECORD READY
MAX

VOLUME
TEST

PLAY
BYPASS

MESSAGE

INSTANT

CODE

CHIME

STATUS

VOICE

FUNCTION

Voice-Capable Alpha Display Keypad

6160V-00-006-V0

MIC

READY

–9–

6160-00-001-V0

About The Keypads (Cont’d)
FIXED-WORD DISPLAY KEYPAD
AWAY: STAY: All burglary zones, interior and perimeter, are armed. Perimeter burglary zones, such as protected windows and doors, are armed. NIGHT and STAY indicators both light when perimeter burglary zones plus pre-selected interior zones (set by the installer) are armed. Entry delay is turned off: Lit with STAY = Instant mode Lit with AWAY = Maximum mode

AWAY
BYPASS

ALARM STAY FIRE CHECK

NIGHT NO AC PHONE TEST NOT READY CHIME BAT INSTANT CANCELED
6150disp

NIGHT-STAY:

FIXED-WORD DISPLAY

INSTANT:

BYPASS: NOT READY:

NO AC: AC: CHIME: BAT: ALARM:

CHECK:

FIRE:

CANCELED:

This appears when one or more burglary protection zones have been bypassed. Appears when burglary portion of the system is not ready for arming (due to open protection zones). The system is ready to arm when this message disappears and the READY indicator light comes on. Appears when AC power has been cut off. System is operating on backup battery power. Appears when AC power is present. Appears when the chime feature is activated. Low battery condition in a wireless sensor (if zone number displayed) or low system battery (if no zone number displayed). Appears when an intrusion has been detected and the system is armed (also appears during a fire alarm or audible emergency alarm). Accompanied by the protection zone in alarm. Appears when a malfunction is discovered in the system at any time, or if an open is detected in a fire zone at any time, or a fault in a DAY/NIGHT burglary zone during a disarmed period. Accompanied by a display of zone number in trouble. Appears when a fire alarm is generated. Accompanied by a display of the zone in alarm. A FIRE display also appears when a fire alarm is manually activated, accompanied by a display of the fire emergency key zone number. Appears when an alarm has been silenced by the Code + OFF sequence and will remain on until another Code + OFF sequence is keyed.

– 10 –

Functions of the Keypads
1 2 3 4

20

19 18 5
ARMED

17 16 15

1 4 7

OFF

2 5 8 0

AWAY

3 6 9 #

STAY

RECORD READY
MAX

VOLUME
TEST

PLAY
BYPASS

6 7 8 9

MESSAGE

INSTANT

CODE

CHIME

MIC

READY

10
6160V-00-007-V0

STATUS

VOICE

FUNCTION

14 13

12

11

Voice-capable 2-line Alpha keypad (shown with flip-down front door removed)

IMPORTANT!
• • Match the numerical callouts in the above graphic with the corresponding number on the following pages for a description of usage. When entering codes and commands, sequential key depressions must be made within 4-5 seconds of one another. If 4-5 seconds elapse without a key depression, the entry will be aborted and must be repeated from its beginning. Be sure to observe this precaution when performing any of the procedures in this manual.

• If you make a mistake while entering a security code, stop, press the [✱] key, and then start over. If you stop in the middle while entering a code, and then immediately start the entry over, an erroneous code might be entered.

– 11 –

Functions of the Keypads (cont’d)
NOTE: The functions printed directly on the keys indicate their primary purpose; the functions printed under some of the keys (shown in brackets under the respective key), indicate their alternate or secondary purpose.

[PLAY] On Voice keypads, used in conjunction with the FUNCTION and VOICE keys to play the recorded message. [ ↑ ] On Voice keypads, used in conjunction with the FUNCTION and VOLUME keys to raise the message and voice system status volume. 5. 4 MAX Arms the entire burglary

1. DISPLAY WINDOW Alpha Display Keypads: 2-line, 32character Liquid Crystal Display (LCD) keypads that display protection point identification, system status, and messages. Fixed-Word Display Keypads: Display protection zone ID and system status messages using pre-designated words in the LCD display area. 2. Disarms burglary portion of the system, silences alarms and audible trouble indicators, and clears visual display after problem's correction. [RECORD] On Voice keypads, used in conjunction with the FUNCTION and VOICE keys to record up to a 2.5minute message.
OFF

system, perimeter and interior, but without entry delay feature. Entering via an entry/exit door will cause an alarm. 6. 5 TEST Tests the system and alarm sounder if disarmed. Refer to Testing The System section for test procedures. 7. 6 BYPASS Removes individual protection zones from being monitored by the system. [ ↓ ] On Voice keypads, used in conjunction with the FUNCTION and VOLUME keys to lower the message and voice system status volume. 8. 7 INSTANT Arms in manner similar to the STAY mode, but without the entry delay feature. Entering via an entry/exit door will cause an alarm. 9. 8 CODE Used to assign additional security codes and attributes for other users of the system. 10. 9 CHIME Turns CHIME mode on and off. When on, the opening of windows or doors while the system is disarmed will sound 3 beeps at the keypad(s).

1

3.

Arms the entire burglary system, perimeter and interior. [VOLUME] On Voice keypads, used in conjunction with the FUNCTION and desired volume control keys ↑ [3] or ↓ [6] to adjust the volume of a recorded message or voice system status.

2 AWAY

4.

3 STAY

Arms perimeter portion of system only. Interior is not armed, allowing within premises without alarm. If pressed twice in arms system in Night-Stay

burglary protection movement causing an succession, mode.

– 12 –

Functions of the Keypads (cont’d)
11. # This key can be used for "Quick Arming" of the system without use of a security code (if programmed). [FUNCTION] On Voice keypads, enables the desired voice or volume function. 12. 0 [VOICE] On Voice keypads, enables the RECORD, VOLUME and PLAY functions. 13. ∗ READY Used to display all open 15. MIC On voice keypads, microphone Message Center recordings. for

16. MESSAGE LED INDICATOR: (RED) On Voice keypads, flashes red when message waiting or lights red (steady) when in record mode. 17. READY LED INDICATOR: (GREEN) Lit when the system is ready to be armed (no faults present). While the system is disarmed, this indicator will go on and off as protection zones are closed and opened. 18. ARMED LED INDICATOR: (RED) Lit when the system has been armed. 19. FUNCTION KEYS: Keys A, B, C, D may have been programmed for a variety of functions, including panic (emergency) functions. For details, see the Function Keys section. 20. INTERNAL SPEAKER: The built-in speaker mimics the alarm sounder during alarms, and will also "beep" during certain system functions. The speaker also provides voice playback for any recorded messages.

protection zones. [STATUS] On Voice keypads, a momentary press of the STATUS key annunciates the current system status. Pressing the STATUS key a second time annunciates and displays system and/or zone faults (if they exist). 14. KEYS 0–9: Used to enter your security code(s).

– 13 –

Entry/Exit Delays
Entry Delay
Entry Delays give you time to disarm the system when you re-enter through the designated entrance door. There are two entry delays (if programmed). The first is for your primary entrance and the second can be used for a secondary entrance, where a longer delay is required to walk to the keypad to disarm the system. You must disarm the system before the entry delay period ends, or an alarm will occur. The keypad beeps during the entry delay period, reminding you to disarm the system. The beeps stop when a code is entered, but will restart after about 15 seconds if an invalid code is entered. You can also arm the system with no entry delay at all by using the INSTANT or MAXIMUM arming modes. These modes provide greater security while on the premises or while away for extended periods of time. See your installer for your delay times.
Partition 1____________________________________________________________________________ Exit Delay: seconds Entry Delay 1: Entry Delay 2:
NOTE: Entry/Exit times set for partition 1 also apply to the Common Zone.

seconds seconds

Partition 2____________________________________________________________________________ Exit Delay: seconds Entry Delay 1: Entry Delay 2: seconds seconds

Exit Delay
Exit delay gives you time to leave through the designated exit door(s) without setting off an alarm. Exit delay begins immediately after arming your system in any arming mode and Alpha Display keypads display the message “You May Exit Now.” When “You may exit now” disappears, the system is fully armed. If programmed, a slow beeping will sound during the exit delay period until the last 10 seconds, which then changes to fast beeping (alerting you to the end of exit delay). If you cannot leave within this delay time period, you should stop, disarm the system, and start over to avoid a false alarm. Exit Delay Restart (if programmed):If you wish to open the entry/exit door to let someone in after arming STAY (the perimeter zones remain armed), you can restart the exit delay at any time – simply press the [✱] key, then let that person in. The system automatically rearms the entry/exit door when the exit delay expires, which avoids having to disarm the system and then rearm it again. Additionally, when the system is armed AWAY, reopening and closing the entry/exit door before exit delay time expires (e.g., re-entering to get a forgotten item), will reset the exit delay time once.

– 14 –

Entry/Exit Delays (cont’d)
Exit Alarms
Exit Error Conditions Whenever you arm the system, the exit delay begins. If an entry/exit door or interior zone is faulted before exit delay expires and remains faulted (e.g., exit door left open), the system sounds an alarm and starts the entry delay timer. If you disarm the system before the entry delay ends, the alarm sound stops and the message "ALARM CANCELED " or "CA" is displayed on the keypad, along with a zone number indicating the faulted zone. No message is sent to the Central Monitoring Station. To clear the exit error condition, the open zone must be made intact; to clear the display, enter your code plus OFF. If you do not disarm the system before the entry delay ends and the faulted zone remains open, the alarm sound continues and an "exit alarm" message is sent to the Central Monitoring Station (after the installer-programmed dial delay expires). The message "EXIT ALARM" or "EA" is displayed on the keypad, along with a zone number indicating the faulted zone. To stop the alarm, the system must be disarmed (your code plus OFF); to clear the display, enter your code plus OFF a second time. An “exit alarm” also results if an entry/exit door or interior zone is faulted within two minutes after the end of the exit delay.
Your system may have been programmed for this feature to minimize false alarms sent to the Central Monitoring Station. Ask your installer if "Exit Alarm" is active in your system. If so, check this box.

VISTA-21iPSIA: The Exit Error condition works the same as described above, except that in addition to the “EXIT ALARM” message, a “zone alarm” message is also sent to the Central Monitoring Station. In addition, if an entry/exit door or interior zone is faulted within two minutes after the end of the exit delay, a “Recent Closing” condition occurs instead of the “exit alarm.” Refer to the next paragraph for details. “Recent Closing” Condition (VISTA-21iPSIA) A Recent Closing condition is similar to the Exit Error condition described above, but occurs if an entry/exit door or interior zone is faulted within two minutes after the initial exit delay expires. If you disarm the system within the two minutes, the alarm sound stops and the message "ALARM CANCELED " or "CA" is displayed on the keypad, along with a zone number indicating the faulted zone. No message is sent to the Central Monitoring Station. If you do not disarm the system within two minutes and the faulted zone remains open, the alarm sound continues and a “recent closing” and a “zone alarm” message are sent to the Central Monitoring Station (after the installer-programmed dial delay expires). The alarm message along with a faulted zone number is displayed on the keypad. To stop the alarm, the system must be disarmed (your code plus OFF); to clear the display, enter your code plus OFF a second time.

– 15 –

Checking For Open Zones
Using the [∗] Key to Display and Announce System Status ∗
Before arming your system, all protected doors, windows and other protection zones must be closed or bypassed; otherwise the keypad will display a "Not Ready" message.
Use the READY key to display all faulted zones, making it easier for you to identify and secure any open zone. 1. Press [✱] (do not enter code first) to display faulted zones. 2. Secure or bypass the zones displayed. The keypad’s READY indicator lights when all protection zones have been either closed or bypassed. 3. Arm the system as desired.
Alpha Display:

DISARMED HIT ∗ FOR FAULTS
Fixed-Word Display: Zone no. and “NOT READY”

Voice Status: Voice keypads (if installed), can announce system status and faulted zones (up to 3 zone descriptors) if the Voice Status feature is turned on. To turn the Voice Status feature on/off: # + 0
(also turns on Voice Chime mode; see Chime mode section) + 2 + 4

To announce Status: Press [#] FUNCTION + [0] VOICE + [∗] STATUS key. (Announces current system status; e.g., “Disarmed Ready to Arm.”) To announce faults and status: Press [#] FUNCTION + [0] VOICE + [∗] STATUS + [∗] again (Announces up to three faulted zones with their zone descriptors, if programmed.)

– 16 –

Arming the System
STAY Mode: Arms Perimeter Only, Entry Delay On
• Used when you want to arm the system with persons staying inside (or if you have pets that are moving throughout the premises). • The perimeter sensors are armed, but interior sensors are left disarmed. • Exit delay begins (you can leave through the entry/exit door, if desired). • An alarm sounds if any protected window or non-entry/exit door is opened. • You may otherwise move freely within the premises. • Persons entering later can enter through an entry/exit door, but they must disarm the system within the entry delay period to avoid sounding an alarm.

NIGHT-STAY Mode: Arms Perimeter Only, Plus Selected Zones
• Use NIGHT-STAY mode to provide increased security while staying inside. • Arms same as STAY mode, but also arms preselected interior sensors (programmed by your installer), while other interior sensors are left disarmed. • Persons entering later can enter through an entry/exit door but they must disarm the system and must not violate any of the programmed interior zones to avoid sounding an alarm. • IMPORTANT: When NIGHT-STAY mode is on, the selected interior zones are armed and cause an alarm if anyone enters those areas (e.g., waking in the middle of the night). To avoid sounding an alarm, you must disarm the system before any activity takes place in those interior zones.

INSTANT Mode: Arms Perimeter Only, Entry Delay Off
• Used when staying inside and do not expect anyone to use an entry/exit door. • Arms same as STAY mode. • An alarm sounds immediately if any protected perimeter window or any door is opened, including entry/exit doors. • IMPORTANT: Arming the system in this mode greatly increases the chance of false alarms. Use extreme care in selecting this mode of arming.

AWAY Mode: Arms Entire System, Entry Delay On
• • • • Used when nobody will be staying inside (including pets). The entire system (interior and perimeter) is armed. Exit delay begins letting you leave through the entry/exit door. An alarm sounds if a protected window or any door is opened, or if any movement is detected inside your premises. • You can re-enter through an entry/exit door, but you must disarm the system within the entry delay period to avoid sounding an alarm.

MAXIMUM Mode: Arms Entire System, Entry Delay Off
• Used when leaving the premises for extended periods (e.g., vacation). • Arms same as Away mode, but entry delay is off. • An alarm sounds same as Away mode, and sounds upon opening entry/exit doors.

– 17 –

Arming the System (cont’d)
Arming Commands
Before arming, close all perimeter doors and windows and make sure the Ready to Arm message is displayed. Mode Press these keys… Keypad Confirms By…
STAY security code + 3 STAY • three beeps† • armed STAY message displayed • red ARMED indicator lights • three beeps† • NIGHT-STAY message displayed • red ARMED indicator lights • three beeps† • armed STAY message displayed • red ARMED indicator lights Note that entry delay is turned off. two beeps†, or, if programmed, beeping for duration of exit delay • armed AWAY message displayed • red ARMED indicator lights Leave the premises through an entry/exit door during the exit delay period to avoid causing an alarm. The keypad beeps rapidly during the last 10 seconds of the exit delay to warn you that it is ending. • same as AWAY (described above) Note that entry delay is turned off.

NIGHTSTAY INSTANT

security code + 3 STAY + 3 STAY

security code + 7 INSTANT

AWAY

security code + 2 AWAY

MAXIMUM security code + 4 MAX

† Arming Ding: In addition to the keypad beeps, the external sounder emits a short “ding” sound after arming, if programmed to do so. The ding confirms that the system is armed, and may occur immediately after the command or be delayed (until arm/disarm report is sent or exit delay expires). Ask your installer about how this feature is set for your system.

Quick Arming If "Quick Arming" was programmed by the installer, the [#] key can be pressed in place of the security code when arming the system in any of the arming modes (except NightStay). However, the security code must always be used when manually disarming the system. Function Key Arming For any arming command, a function key may have also been programmed for your system. If so, you can press and hold the appropriate function key for 2 seconds to arm the system. See your installer for the designated functions (see Single Button Arming section). Refer to the Accessing Other Partitions section for information on multi-partition arming.

– 18 –

Arming the System (cont’d)
Single Button Arming
The “A”, “B”, “C”, and/or “D” keys on your keypad may have been programmed for single-button arming. Note that while it is not necessary to use a security code for arming (by using the Quick Arm method described previously), a security code must always be used when manually disarming the system. If Single-Button Arming is programmed: • A function key has been assigned to a specific type of arming: STAY mode, NIGHT-STAY mode, AWAY mode, or STEP-ARMING (see Step-Arming paragraph). • You DO NOT need to enter your security code before pressing the function key but you always need your security code to DISARM the system. Before arming, close all perimeter doors and windows. 1. Press and hold the assigned function key for 2 seconds (no code is required). Function keys are shown below.
A B C D
Alpha Display:

1 4 7

OFF

2 5 8 0

AWAY

3 6 9 #

STAY

DISARMED READY TO ARM
Fixed-Word Display: Green LED lit

TEST

BYPASS

INSTANT

CODE

CHECK

*

READY

ADT3000-007-V0

2. The keypad begins beeping and displays the armed message. The red ARMED indicator also lights.

Alpha Display:

ARMED***AWAY*** YOU MAY EXIT NOW
Fixed-Word Display: AWAY

Single Button “Step” Arming
Single-Button “Step” arming may be programmed into one of the lettered keys (A, B, C, or D). Check with your installer to see if this has been done in your system. If Step-Arming is programmed: • The assigned key provides a choice of three levels of security. • The selected key can be pressed once, twice, or three times, increasing the level of security with each press, as follows Key A, B, C, D First Press Armed-STAY Second Press Armed NIGHT-STAY (if programmed) Third Press Armed-AWAY

– 19 –

Keyswitch
Using the Keyswitch
Your system may be equipped with a keyswitch for use when arming and disarming. Red and green lights on the keyswitch plate indicate the status of your system as follows: Green Light: Lights when the system is disarmed and ready to be armed (no open zones). If the system is disarmed and the green light is off, it indicates the system is not ready (one or more zones are open). Red Light: Lights or flashes when system is armed in AWAY or STAY mode. See your installer for the meanings of the lit red light: Lit Steady = system armed AWAY or system armed STAY and exit delay has expired Flashing = system armed STAY and exit delay timer active Rapid flashing = an alarm has occurred (memory of alarm). Before arming, close all perimeter doors and windows. To arm in the AWAY mode: Turn the key to the right for 1/2 second and release. Keypads beep twice and the red indicator lights or flashes. To arm in the STAY mode: Turn the key to the right and hold for longer than 1 second, then release. Keypads beep three times and the red indicator lights or flashes. To disarm the system: Turn the key to the right and release. The red light turns off

GREEN

RED

keyswitch-001-V1

– 20 –

Disarming and Silencing Alarms
Using the [OFF] key
The OFF key is used to disarm the system, silence alarm and trouble sounds, and clear alarm memories. IMPORTANT: If you return and the main burglary sounder is on, DO NOT ENTER, but CONTACT THE POLICE from a nearby safe location. If you return after an alarm has occurred and the main sounder has shut itself off, the keypad will beep rapidly upon your entering, indicating that an alarm has occurred during your absence. LEAVE AT ONCE, and CONTACT THE POLICE from a nearby safe location. 1.
(Security Code)

+ 1

OFF

Alpha Display:

∗∗∗∗DISARMED∗∗∗∗ READY TO ARM
Fixed-Word Display: READY

The “READY” indicator light will be lit if all zones are secure, and the keypad will emit a single tone to confirm that the system is disarmed. NOTE: If entry delay has started (you’ve opened the entry door), you do not need to press the OFF key – simply enter your security code. The system will disarm in about 15 seconds after the last digit of the code is entered.

2. To Silence a Burglary Alarm and Clear a Memory of Alarm Enter your security code and press the OFF key to silence the alarm (or warning tones of a Memory of Alarm). Note the zone in alarm on the keypad display, and correct the problem (close door, window, etc.). After correcting the problem, enter the security code plus OFF sequence again to clear the keypad’s Memory of Alarm display. 3. To Silence a Fire Alarm or Carbon Monoxide Alarm and Clear a Memory of Alarm Simply press the OFF key to silence the alarm. Then enter the security code plus OFF sequence twice to clear the keypad's Memory of Alarm display. See the Fire Alarm System section.

– 21 –

Bypassing Protection Zones
Using the BYPASS Key
Use this key when you want to arm your system with one or more zones
intentionally unprotected. The system must be disarmed first. Vent Zones: Your system may have certain windows set as “vent” zones, which are automatically bypassed if left open when arming the system (you do not need to manually bypass them). However, if a vent zone window is closed after arming, it becomes protected and will cause an alarm if opened again while the system is armed. When bypassing zones: • The system must be disarmed before you can bypass zones. • Bypassed zones are unprotected and will not cause an alarm if violated. • The system will not allow fire zones to be bypassed. • Zones are automatically unbypassed when the system is disarmed. 1.
(Security Code)

+ 6 BYPASS + zone numbers (see below) Enter the 2-digit zone number(s) for the zone(s) to be bypassed (e.g., 06, 10, 13, etc.). Single digit zone numbers must be preceded by a zero (e.g. 05, 06).

Alpha Display:

DISARMED HIT ∗ FOR FAULTS
Fixed-Word Display: NOT READY Alpha Display:

2. When finished, the keypad will momentarily display a "Bypass" message for each bypassed zone number. Wait for all bypassed zones to be displayed. Arm the system as usual. When armed, the arming message is displayed with “ZONE BYPASSED.” To display bypassed zones prior to arming, enter your security code and press the [6] BYPASS key.

DISARMED BYPASS READY TO ARM
Fixed-Word Display: BYPASS Alpha Display:

ARMED: STAY ZONE BYPASSED
Typical armed display after bypassing zones.

– 22 –

Bypassing Protection Zones (cont’d)
Quick Bypass
If programmed, "Quick Bypass" allows you to easily bypass all open (faulted) zones without having to enter zone numbers individually. This feature is useful if, for example, you routinely leave certain windows open when arming at night. 1.
(Security Code)

+

6 BYPASS + [#]

Alpha Display:

In a few moments, all open zones will be displayed and automatically bypassed. Make sure that only those zones that you wish to leave unprotected are bypassed, and that there are no other zones unintentionally left open. 2. Wait for all bypassed zones to be displayed, then arm the system as desired. Ask your installer if "Quick Bypass" is active for your system, and if so, check here:

DISARMED HIT ∗ FOR FAULTS
Fixed-Word Display: NOT READY

Alpha Display:

DISARMED BYPASS READY TO ARM
Fixed-Word Display: BYPASS

– 23 –

Chime Mode
Using the Chime Mode
CHIME mode alerts you to the opening of a perimeter door or window while the system is disarmed. When Chime mode is activated: • Three tones sound at the keypad whenever a perimeter door or window is opened. • Interior zones do not produce a tone when they are faulted. • Pressing the READY key will display the open protection points. • Chime mode can be used only while the system is disarmed. To turn Chime Mode on: + 9 CHIME
(Security Code)
Alpha Display:

The CHIME message will appear. Perimeter zones will cause a tone when faulted. To turn Chime Mode off: + 9 CHIME
(Security Code)

DISARMED CHIME READY TO ARM
Fixed-Word Display: CHIME Alpha Display:

∗∗∗∗DISARMED∗∗∗∗ READY TO ARM
Fixed-Word Display: READY

The CHIME message will disappear.

Using the Voice Chime
Voice keypads have a feature that works in concert with the Chime Mode called Voice Chime. Voice chime provides a voice status annunciation, chime, and display when any faulted entry/exit or perimeter zone exists. Ask your installer if this option has been enabled for your system. To turn Voice Chime Mode on or off: # + 0
(normal Chime mode must be on first) + 2 + 4

When Voice Chime is on, faulted zones cause a voice status announcement, chime and display. When off, the sounder still provides chime if normal Chime mode is on.

– 24 –

Date and Time
Viewing the Current Date and Time
The master users can view the system time and date setting on an alpha keypad. Other users can view the time/date if a function key has been programmed to do so. + [#] + [6] [3]
(Master Code)
Alpha Display:

OR, Press the function key (A, B, C, or D) for viewing current date and time, if programmed. A typical time/date display is shown. The display will remain on for about 30 seconds or until a key is pressed. “A ” “B” “C ” “D ”

∗∗∗∗DISARMED∗∗∗∗ READY TO ARM

TIME/DATE SAT 12:05AM_05/09/00

If one of the above keys has been programmed for the date/time display feature, place a check mark in the box beneath that key.

Setting the Date and Time
NOTE: All partitions must be disarmed before date/time can be set. You can set the time and date by doing the following: 1.
(Master Code)

+[#] + [6] [3]

Alpha Display:

∗∗∗∗DISARMED∗∗∗∗ READY TO ARM TIME/DATE SAT 04:04PM 10/17/00
Current time display

2. Press [∗] when the time/date is displayed. A cursor appears under the first digit of the hour. To move cursor ahead, press [∗]. To go back, press [#]. • Enter the 2-digit hour setting. • Enter the 2-digit minute setting. • Press [1] for PM or [2] for AM. • Enter the last two digits of the current year. • Enter the 2-digit month setting. • Enter the 2-digit day setting. 3. To exit, press [∗] when cursor is at the last digit, or wait 30 seconds.

TIME/DATE SAT 04:04P2000/10/17
Time/date editing display

– 25 –

Panic Keys
Using Panic Keys
Your system may have been programmed to use special keys to manually activate emergency (panic) functions as follows: This Function Silent Alarm With This Sounding… no audible alarm; displays, “Press [∗] to show faults,” indicating that a silent alarm has been initiated. Audible Alarm audible alarm a loud, steady alarm at keypad(s) and at any external sounders that may be connected. Personal Alarm auxiliary alarm steady alarm sound at keypad(s), but not at external bells or sirens. Fire Alarm fire alarm temporal (pulsing) sound at external bells and sirens. *All panic functions send signals to the Central Monitoring Station, if connected.
Normal Alpha Display:

Sends This Signal* silent alarm

To activate a Panic Function: Press and hold down for at least 2 seconds whichever lettered key on the keypad has been programmed for the desired emergency function. OR Press both keys of the assigned key pair at the same time.

∗∗∗∗DISARMED∗∗∗∗ READY TO ARM
Fixed-Word Display: READY Typical Panic Alpha Display:

ALARM 96 ZONE 96
Fixed-Word Display: 96 and ALARM

A
ZONE 95
ARMED

PRESS BOTH KEYS OF DESIRED PAIR AT THE SAME TIME
1 4 7
OFF

2 5 8 0

AWAY

3 6 9 #

STAY

B
ZONE 99

READY
ARMED

MAX

TEST

BYPASS

1 4 7

OFF

2 5 8 0

AWAY

3 6 9 #

STAY

ZONE 95

ZONE 96
CHIME

INSTANT

CODE

READY

MAX

TEST

BYPASS

READY

READY

D

6160-00-003-V0

ZONE 96

ZONE 99

Lettered Panic Keys

Panic Key Pairs

See your installer and use the chart provided in the Features Programmed in Your System section to note the functions that have been programmed for your system.

– 26 –

6160-00-004-V0

C

INSTANT

CODE

CHIME

Macro Key Programming & Usage
About Macro Keys
The “A”, “B”, “C” or “D” keys can be used to automatically activate a series of commands of up to 16 keystrokes, if programmed for this function. These keystrokes, as a group, are called “macros” and are stored in the system's memory. • Typical macro functions can include: - Arming sequences: STAY, NIGHT-STAY, INSTANT, or AWAY - Bypassing particular zone(s) - Activating relay(s) for turning on (or off) lights, fans, etc. • Up to four macros can be assigned – but no more than one macro to a key. • Macros can be activated only by users with authority levels authorized to perform the macro’s function. NOTE: The installer must activate the desired function key (using *57 Function key Menu Mode) before macros can be assigned. See the chart at the back of this manual for the key(s) assigned for macros. 1.
(Master Code)

+ [#] + [6] + [6]

Alpha Display:

∗∗∗∗DISARMED∗∗∗∗ READY TO ARM SELECT MACRO 1-4 MACRO DISPLAY

2. Enter the macro number (1-4) to be programmed at the “Select Macro?” prompt. Remember, only one macro can be assigned to each key. 3. If a macro has been previously defined, the keystrokes are shown on the bottom line of the display; otherwise the display is blank. To exit this mode (and keep the existing macro definition), press any key except the [∗] key. The system returns to normal mode. To define a macro for the selected key, press [∗] and continue with the next prompt. Enter the first of the series of desired commands, (do not include your master code), then press/hold the “D” key for at least two seconds to complete the first command. This key terminates each command, and appears as an “F” in the keypad display.

0

MACRO PGM

– 27 –

Macro Key Programming & Usage (cont’d)
The keypad beeps to acknowledge your input and displays the command you entered (followed by “F”). 4. Enter the next command, followed by press/holding the “D” key for at least two seconds. The keypad beeps and displays the keystrokes entered so far. 5. Repeat until the all the desired commands (up to 16 characters including the “F”s) have been entered. Be sure to check your keystrokes before continuing. If you made a mistake, you must start over. 6. To exit, press/hold the “D” key for at least two seconds. The display returns to system status and indicates system is ready.

Example of Macro Programming
Suppose you want to (1) bypass the two upstairs window zones, then (2) turn on an exterior light, and then (3) arm the security system in the AWAY mode. The procedures in the table that follows show you how you would program this macro: Function
1. Bypass zones 02 & 03 2. Insert terminator 3. Turn light on (device 01) 4. Insert terminator 5. Arm system AWAY 6. Insert terminator
Typical Macro Alpha Display:

MACRO PGM 60203F#701F2F
Keypad Display

Keystrokes Required
Press BYPASS [6] key, then 2-digit zone numbers 02 & 03. Press the “D” key for at least 2 seconds. Press [#] and 7 key for “device ON”, and [01] key for selecting device 1. Press the “D” key for at least 2 seconds. Press AWAY [2] key. Press the “D” key for at least 2 seconds.

60203 60203F 60203F#701 60203F#701F 60203F#701F2 60203F#701F2F

Using a Programmed Macro Key
∗∗∗∗DISARMED∗∗∗∗ READY TO ARM ENTER USER CODE ∗∗∗∗
1. Press the Macro key programmed for the desired series of commands for at least 2 seconds. The “Enter User Code” prompt appears. The prompt remains displayed for up to 30 seconds. 2. Enter your 4-digit security code. The programmed macro sequence begins automatically after the user code is entered.

– 28 –

Using Device Commands
About Device Commands
Your system may be set up so that it can control certain lights or other devices. • Some devices may be automatically turned on or off by the system. • You may be able to override automatically controlled devices using the commands described below. • Some devices can be manually turned on or off using the commands described below. • See your installer for a list of devices that may be set up for your system. A list of these devices is provided at the back of this manual for you to fill out. To Activate Devices: + [#] + [7] + 2-digit device number
(Security Code)
Alpha Display:

Devices associated with that device number activate. To Deactivate Devices: + [#] + [8] + 2-digit device number
(Security Code)

∗∗∗∗DISARMED∗∗∗∗ READY TO ARM
Fixed-Word Display: READY

Devices associated with that device number deactivate.

– 29 –

Paging Feature
About Automatic Paging
Your system may be set up to automatically send messages to up to four pagers as certain conditions occur in your system. • The following events can be programmed by your installer to be sent to the pagers: arming and disarming†, alarms, and trouble conditions. († reports when arming/disarming from a keypad using a security code; auto-arming/disarming, arming with assigned button, and keyswitch arming do not send pager messages.) • You can also program the system to send an automatic pager message to alert you in the event that someone has not arrived home (disarmed the system) within a defined period of time (see the Scheduling section for details on programming a “latch key report”). • Your installer programs the pager phone numbers and reporting events. • The pager message consists of a 7-digit system status code that indicates the type of condition that has occurred. • An optional, predefined 16-digit character string can precede the 7-digit system status code; these characters can consist of a PIN no., subscriber account no., or any additional data that you may wish to have sent to the pager. • The pager display format is as follows:
Optional 16 digits 3-digit Event Code 1-digit Partition No. + 3-digit Zone No. or User No.

AAAAAAAAAAAAAAAA – BBB – CCCC
A=
Optional 16-digits for Account numbers, PIN numbers, or any other data; programmed by the installer, if required.

B=
A 3-digit code that describes the event that has occurred in your system (see for event codes table below)

C=
A 1-digit Partition number plus a 3-digit Zone or User number, depending on the type of event that has occurred, where: • alarms and troubles display zone number • arming/disarming (opens/closes) display user number

The 3-digit Event Codes (BBB) that can be displayed are: 911 = 811 = 101 =
Alarms. The 4-digit number (CCCC) following this code is the partition no. and zone no. that caused the alarm. Troubles. The 4-digit number (CCCC) following this code is the partition no. and zone no. or device address that caused the trouble. Open (system disarmed). The 4-digit number (CCCC) that follows this code is the partition no. and user no. that disarmed the system.

102 =
Close (system armed). The 4-digit number (CCCC) that follows this code is the partition no. and user no. that armed the system.

Examples of typical 7-digit pager displays follow. Ex. 1. Ex. 2. 911–1004 = R eporting of an alarm (911) caused by a fault on zone 4 on Partition 1 (1004).

1 0 2 – 2 0 0 5 = Reporting of a closing–system arming (102)– by user 5 in Partition 2 (2005).

– 30 –

Paging Feature (cont’d)
About Manual Paging
Your system may be set up so you can manually send a message to up to four pagers. • Your installer programs the paging function key and the pager phone numbers. • Pressing the paging keys sends the message
999–9999

to the selected pager.

• This message could mean “call home”, “call your office”, or any other prearranged meaning. • See the Paging chart at the back of this manual for details of the paging setup for your system. 1. Press and hold the programmed Paging Key for at least 2 seconds (wait for beep), then press the pager number* (1-4) representing the pager intended to receive the message. 2. The recipient, on seeing the 999–9999 message, will understand the prearranged meaning of this signal. * If no number is pressed, the message is sent to pager 1.
Alpha Display:

∗∗∗∗DISARMED∗∗∗∗ READY TO ARM
Fixed-Word Display: READY

999-9999
Pager Display

Latch Key Paging
You can program a schedule that causes a pager report to be sent if the system is not DISARMED by the scheduled time (see Scheduling section, event “03”). For example, a working parent might want a message to be sent to a pager if their child did not arrive home from school and disarm the system by a certain time. If programmed, the message that is sent is:
7 7 7 –7777 .

– 31 –

Security Codes & Authority Levels
About Security Codes
Your installer assigned a master code that is used to perform all system functions. In addition, you can assign up to 47 different security codes for use by other users. • Only the System Master and Partition Master can assign security codes to users. • Users are identified by 2-digit user numbers and are pre-assigned to either partition 1 or partition 2. • Only the System Master can change user partitions. • In addition to a security code, each user is assigned various system attributes. • Security codes can be used interchangeably within a partition when performing system functions (a system armed with one user's code can be disarmed by another user's code), with the exception of the Guest code Arm Only code described below. • Security code programming involves these steps: 1. Choose a user number from the set of users assigned to the partition in which the user will be operating, and assign a 4-digit security code. 2. Assign an authority level to that user. 3. Assign other attributes as necessary (see attributes on the next page). NOTE: The factory settings are designed to meet most normal user situations. Therefore, the only step you usually need to do when adding users is assign a user number (from the partition’s pre-assigned user numbers) and a security code.

Authority Level Definitions
Authority levels define the system functions a particular user can/cannot perform.
Level Title
N/A System Master (default = 1234) Standard User: Arm Only: Guest:

Explanation
Reserved for user 02; Can perform all system functions and assign codes in both partitions; can change its own code as follows: Master code + [8] + 02 + new master code + new master code again Can only perform security functions in assigned partition. Cannot perform system functions reserved for the master user. Can only arm the system. Cannot disarm or do other functions. Can arm the system in assigned partitions, but cannot disarm the system unless the system was armed with this code. This code is typically assigned to someone (e.g., babysitter or cleaner) who has a need to arm/disarm the system only at certain times. The user of this code should not use the “Quick Arming” feature. Intended for use when you are forced to disarm or arm the system under threat. When used, the system will act normally, but can silently notify the Central Monitoring Station of your situation, if that service has been provided. Can do everything a standard user can do, and can assign security codes to users in their partition.

0 1 2

3

Duress Code:

4

Partition Master

– 32 –

Security Codes & Authority Levels
How to Assign Security Codes and Attributes

(cont’d)

The following lists the various command strings for adding security codes and attributes Refer to the User Setup chart at the back of this manual for factory defaults of user attributes and to keep a record of user programming.
NOTE: Partition Master codes apply only to those user numbers previously assigned (by the system master/installer) to the partition master’s partition.

Add Security Code:
(Users 03/33 are preset to partition programmers, but can be changed.)

System/Partition Master code + [8] + user no. + new user’s security code User 01 = installer User 03 = partition 1 master User 02 = master User 33 = partition 2 master The Keypad beeps once to confirm that new user was added. The user code and all attributes* programmed for this user number, including any associated RF keys, are erased from the system. (*except assigned partition)

Delete Security Code: System/Partition Master code + [8] + [user no.] + [#] [0]

Authority Level:
Factory Defaults: users 04-32/34-49 = 0 users 03/33 = 4

System/Partition Master code + [8] + [user no.] + [#] [1]+ auth. level Authority Levels (see definitions on previous page): 0 = standard user 3 = duress 1 = arm only 4 = partition master 2 = guest System/Partition Master Code + [8] + [user no.] + [#] [2]+ group (1-8) You can assign users to a group, then set an access schedule that defines the times this group of users can operate the system. The system ignores these users outside the scheduled times. System Master Code + [8] + [user no.] + [#] [3] + [0] + partition(s) + [#] This command assigns the partitions the user can access. If more than one, enter partition numbers sequentially, then press [#] to end. E.g., master code + [8] + [user no.] + [#] [3] + [0] + [1] [2] + [#] gives the user access to partitions 1 and 2 and the common partition. Partition Entries: 1 = partition 1 and common 2 = partition 2 and common 3 = common partition only Master/Part. Prog. Code + [8] + [user no.] + [#] [4]+ zone no. Use this command to assign a wireless button device (keyfob) to this user (keyfob must be enrolled in system first; see installer). Zone number: enter the zone number assigned to a button on the keyfob that will be used for arming/disarming by this user. Master/Part. Prog. Code + [8] + [user no.] + [#] [5] + 0 or 1
You can program a user so that a message is sent to a pager

Access Group:
Factory Defaults:: none

User’s Partition:
Factory Defaults: Part. 1 = users 03-32 Part. 2 = users 33-49

RF User Number:
Factory Defaults:: none

Pager On/Off:
Factory Defaults: users 01-49 = 1 (on)

whenever this code is used to arm or disarm the system. Paging On/Off: 1 = allow paging; 0 = no paging for this user

– 33 –

Accessing Other Partitions
About Accessing Partitions
(GOTO Command and Multi-Partition Arming) Each keypad is assigned a default partition for display purposes, and will show only that partition's information. • If the user is authorized, a keypad in one partition can be used to perform system functions in the other partition by using the GOTO command. Refer to the GOTO section. • If the user is authorized, that user can arm other partitions. Refer to the MultiPartition Arming section. The following table shows the relationship of the keypads in each partition when system is armed and disarmed.
PARTITION 1
Arming State Keypad Status Partition 1 Only Partition 1 and Common Zone Partition 1 Only Partition 1 Only

PARTITION 2
Arming State Disarmed Armed Disarmed Armed Keypad Status Partition 2 Only Partition 2 Only Partition 2 and Common Zone Partition 2 Only

COMMON ZONE (LOBBY, etc.)
Arming State Disarmed Disarmed Disarmed Armed Keypad Status Common Zone Only Common Zone Only Common Zone Only Common Zone Only

Condition 1 Condition 2 Condition 3 Condition 4

Disarmed Disarmed Armed Armed

When both partitions are disarmed, the keypad in each partition displays zone status for its partition only. The common zone keypad shows the status in that zone only. See Condition 1 above. When partition 1 is disarmed and partition 2 is armed, the keypad in partition 1 shows the status of partition 1 and the common zone. Partition 2 will display the status of partition 2 only. See Condition 2 above. When partition 1 is armed and partition 2 is disarmed, the keypad in partition 1 shows the status of partition 1 only. Partition 2 will display the status of partition 2 and the common zone. See Condition 3 above. As long as any one of the two partitions is disarmed, the common zone will always be disarmed. The common zone will be armed only when both partition 1 and 2 are armed. See Condition 4 above.

– 34 –

Accessing Other Partitions (cont’d)
Using the GoTo Command
If the user is authorized, a keypad in one partition can be used to perform system functions in the other partition by using the GOTO command. • You must use an Alpha keypad to access another partition. • Keypads automatically return to their original partition after 30 seconds with no keypad activity. 1. + [∗] + partition number (0,1,2,3)
(Security Code; only applies if user has access to other partitions) Alpha Display:

0 = return to keypad’s original partition. 1 = partition 1; 2 = partition 2; 3 = common zone The keypad beeps to confirm the partition change. 2. The keypad remains in the new partition until directed to go to another partition, or until it automatically returns to the original partition. The active partition number is displayed in the upper left portion of screen, if the option is selected.

1 DISARMED READY TO ARM
Fixed-Word Display: Green LED lit Alpha Display:

2 DISARMED READY TO ARM
Fixed-Word Display: Green LED lit

Multi-Partition Arming
Some users can be given Multi-Partition arming ability by being assigned to both partitions when programming user attributes. When attempting to arm multi-partitions: • You must use an Alpha keypad. • The system arms only if all partitions are “ready to arm.” • If any partition is “not ready,” the system does not arm at all. • You can use the GOTO command to bypass open zones before arming. • If any partition is already armed when global arming is attempted, that partition remains in its existing armed state. + [0] + arm command (see list below)
(Security Code)
Alpha Display:

Multi-Partition Arming Commands 2 = arms all partitions AWAY 3 = arms all partitions STAY 33 = arms all partitions NIGHT-STAY 4 = arms all partitions MAXIMUM 7 = arms all partitions INSTANT 1 = disarms all partitions

1 DISARMED READY TO ARM
Fixed-Word Display: Green LED lit

– 35 –

Accessing Other Partitions (cont’d)
Common Zone Operation
Your system may have been set up to use a common zone, which is an area shared by users of both partitions, such as a foyer or lobby. If so, please note the following: • The common zone will sound and report alarms only when both partitions are armed. If only one partition is armed, the system ignores faults on the common zone. • Either partition may arm its system if the common zone is faulted, but once armed, the other partition will not be able to arm unless the common zone is first bypassed or the fault is corrected. • Faults on the common zone are displayed on common partition keypads, and will also appear on another partition’s keypad when the alternate partition is armed. • Either partition can clear and restore the common zone after an alarm. • Entry/exit time for the common zone is the same as for partition 1.

Ask your installer if a "common zone" was assigned. If so, check this box

– 36 –

Scheduling
About Scheduling
The system provides to 16 end-user schedules (programmable by master/installer only), which can control various types of events. • Each schedule causes a defined event to start and stop (when appropriate) at a specified time. • Schedules can be set to automatically repeat at various intervals. • Schedules can be set for random starting, if desired.

Creating Schedules
1.
(Master Code)

Alpha Displays:

+ [#] + [6] [4]

1 DISARMED READY TO ARM ENTER SCHED NO. 00=QUIT 00 ENTER EVENT CLEAR EVENT 00

2. Enter a 2-digit schedule number from: 01-16. Press [∗] to continue. 3. Enter the desired 2-digit event number from the list: 00 = clear the scheduled event 01 = turn a programmed output on or off

(see Using Device Commands section for a list of output device numbers used in your system) 02 = set a user access schedule for one or more users (see Security Codes section for an explanation of access groups) 03 = send a “latch-key” report to a pager if the system is not disarmed by a specified time; message sent is “777-7777.” 04 = automatically arm the system in STAY mode at a specified time 05 = automatically arm the system in AWAY mode at a specified time 06 = automatically disarm the system at a specified time 07 = Display the word “REMINDER” at a specified time (if selected, the keypad beeps every 30 seconds beginning when the word “REMINDER” is first displayed, and the display alternates with the normal keypad display about every 4-5 seconds. To stop the beeps and cancel the display once it starts, press any key). Press [∗] to continue. 4. For event number “01,” enter the output number RELAY NUMBER associated with this schedule. 00 Otherwise, this prompt is skipped. Press [∗] to continue to the “Start” prompt shown on the next page.

– 37 –

Scheduling (cont’d)
5. For event number “02,” enter the access group number. Otherwise, this prompt is skipped. Press [∗] to continue to the “Start” prompt below. 6. For event numbers “03-07,” enter the partition number to be armed or disarmed. 0 = arm all; 1 = partition 1; 2 = partition 2; 3 = arm common Otherwise, this prompt is skipped. Press [∗] to continue to the “Start” prompt. 7. Enter the event’s start time and days of week. Hour = 00-12; minute = 00-59 AM = 0; PM = 1 Days = Position the cursor under the desired days using the [∗] key to move forward, then press “1” to select the day. Press [∗] to continue. 8. If applicable, enter the event’s stop time and days of week (applies only to event numbers 01, 02, and 03). Refer to step 7 for available entries. Press [∗] to continue. 9. Enter the desired repeat option. 0 = no repeat 1 = repeat schedule weekly 2 = repeat schedule biweekly (every other week) 3 = repeat schedule every third week 4 = repeat schedule every fourth week e.g., To make a schedule that happens everyday you would select all days with a repeat count of 1. To make a schedule that runs for one week then stops, select everyday with a repeat count of 0. 10. For event number 01 (output on/off), select the randomize option, if desired. 0 = no; 1 = yes If selected, the schedule times will vary within 60 minutes of the “hour” time. For example, if a schedule is set to start at 6:15pm, it will do so the first time 6:15pm arrives, but on subsequent days it will start anytime between 6:00 and 6:59 p.m. Press [∗] to continue.

GROUP NUMBER X PARTITION X

START HH:MMAM

SMTWTFS 1000000

STOP

SMTWTFS

HH:MMAM 1000000

REPEAT OPTION 0-4 X

RANDOMIZE 0=NO 1=YES

X

– 38 –

Event Logging Procedures
About Event Logging
The system records various events in a history log, which can be viewed by the master user on an Alpha Display keypad. • The Event Log holds up to 100 events. • Events are displayed in chronological order, from most recent to oldest. • When the log is full, the oldest event is replaced by the logging of any new event.

Viewing the Event Log
1.
(Master Code)

+ [#] + [6] + [0]

Alpha Displays:

∗∗∗∗DISARMED∗∗∗∗ READY TO ARM

2. The system displays the most recent event as follows: • event number • type of event, identified by its corresponding code (refer to the code table that follows) • zone or user number (depending on type of event) • partition in which event occurred • time and date of the event’s occurrence. 3. Pressing [∗] displays previous events (back in time). Pressing [#] displays events forward in time. 4. Exit the event log by pressing any key other than [∗] or [#].

001 E441 U001 P1 12:34AM 01/02/00

Understanding the Type of Event Displayed
If the event code is preceded by an E (as in the above display), it means that the event is new and ongoing; if preceded by an R, it means the event has been restored.
Code 110 121 122 123 Definition Fire Alarm Duress Alarm, 24-hour Silent Alarm, 24-hour Audible Code 131 132 134 135 Definition Alarm, Perimeter Alarm, Interior Alarm, Entry/Exit Alarm, Day/Night

– 39 –

Event Logging Procedures (cont’d)
Code 143 145 146 150 162 301 302 305 321 333 339 (803) 341 344 350 (951) 350 (952) 351 353 354 373 374 380 381 382 383 384 393 Definition Alarm, Expansion Module ECP Module cover tamper Silent Burglary Alarm, 24-Hour Auxiliary/Monitor zone Carbon Monoxide AC Power Low System Battery/Battery Test Fail System Reset (Log only) Bell/Siren Trouble Trouble, Expansion Mod. Supervision GSM Module Power-On Reset Trouble, ECP Cover Tamper RF Receiver Jam Ethernet Communication Path Failure GSM Communication Path Fail Telco Line Fault Long Range Radio (GSM) Trouble Comm Fail (log only) Fire Loop Trouble Exit Error Alarm Global Trouble, Trouble Day/Night RF Supervision Trouble Supervision Auxiliary Wire Zone RF Sensor Tamper RF Sensor Low-battery Clean Me 627 628 642 750 -789 442 459 570 601 602 606 607 623 625 Code 401 403 406 407 408 409 441 Definition Disarmed, Armed AWAY, Armed MAXIMUM Schedule Arm/Disarm AWAY Cancel by User Remote Arm/Disarm (Downloading) Quick Arm AWAY Keyswitch Arm/Disarm AWAY Disarmed/Armed STAY/INSTANT, Quick-Arm STAY/INSTANT Keyswitch Arm/Disarm STAY Recent Closing Bypass Manually Triggered Dialer Test Periodic Test AAV to Follow Walk Test Entered/Exited Event Log 80% Full Real-Time Clock was Changed (log only) Program Mode Entry (log only) Program Mode Exit (log only) Latch Key (log only) Reserved for Configurable Zone Type report codes (check with central station when using these codes)

NOTE: Ask your installer to explain the meaning of any code you do not understand.

– 40 –

Testing the System
About Testing the System
Using the Test mode allows each protection point to be checked for proper operation. Testing should be conducted weekly to ensure proper operation. • The keypad sounds a single beep about every 30 seconds as a reminder that the system is in the Test mode. • Alarm messages are not sent to your Central Station while Test mode is on. Alpha Displays: 1. Disarm the system and close all protected windows, doors, etc. The READY indicator light should come on ∗∗∗∗DISARMED∗∗∗∗ if all zones are intact (i.e., all protected windows, READY TO ARM doors, etc. are closed. 2.
(Master Code)

+ 5 TEST then [0] (walk) The Dial test (option “1”) is intended for the installer and should not be used unless directed to do so by your Security System Representative.

1 = DIAL, 0 = WALK

3. Listen. The external sounder should sound for about 1 second then turn off. If the sounder does not sound, CALL FOR SERVICE. The “Test in Progress” display appears only on the keypad that started the test.

TEST IN PROGRESS

4. Fault zones. Open each protected door and window in turn and listen for three beeps from the keypad. Identification (zone number or zone description) of each faulted protection point should appear on the display. The display clears when the door or window is closed. 5. Walk in front of any interior motion detectors (if used) and listen for three beeps. The identification of the detector should appear on the display when it is activated. The display clears when no motion is detected. Note that if wireless motion detectors are used, there is a 3-minute delay between activations. This conserves battery life. 6. Test all smoke detectors, following the manufacturer's instructions. The identification of each detector should appear on the display when each is activated. If a problem is experienced with any protection point (no confirming sounds, no display), call for service immediately. When all protection points have been checked and are intact (closed), there should be no zone identification numbers displayed on the keypad. 7. Exit test mode:
(Security Code)

+

1 OFF

If the test mode is inadvertently left active, it automatically turns off after 4 hours. During the final five minutes, the keypad will emit a double beep every 30 seconds.

– 41 –

Trouble Conditions
"Check" and "Battery" Displays The word CHECK on the keypad's display, accompanied by a
"beeping" at the keypad, indicates a trouble condition in the system. To silence the beeping for these conditions, press any key. 1. A display of "CHECK" and one or more zone numbers indicates that a problem exists with the displayed zone(s) and requires your attention. Determine if the zone(s) displayed are intact and make them so if they are not. If the problem has been corrected, the display can be cleared if you enter the OFF sequence (security code plus OFF key) twice. If the display persists, CALL FOR SERVICE. Note: A display of CHECK 70 on Alpha Display keypads indicates that the wiring connection to the external sounder is at fault (opened or shorted), and you should CALL FOR SERVICE. See “BELL FAILURE” on next page. A display of CHECK 90 indicates that RF interference may be impeding the operation of wireless sensors* in the system. See “Rcvr Jam” on next page. 2. If there are wireless sensors* in your system, the CHECK condition may also be caused by some change in the environment that prevents the wireless receiver from receiving messages from a particular sensor. CALL FOR SERVICE if this occurs. * Not all systems use wireless sensors.

IF YOU CANNOT CORRECT A "CHECK" DISPLAY, CALL FOR SERVICE.
TYPICAL "CHECK" DISPLAYS

06
CHECK

AC

CHECK 06 BEDROOM WINDOW
ALPHA DISPLAY KEYPAD

FIXED-WORD DISPLAY KEYPAD

– 42 –

Trouble Conditions (cont’d)
Words or letters in parentheses ( ) are those that are displayed on Fixed-Word Display keypads.

Other Trouble Displays

COMM. FAILURE (or FC) SYSTEM LO BAT (or BAT with no zone No.)

Indicates that a failure has occurred in the telephone communication portion of your system. CALL FOR SERVICE. Indicates that a low system battery condition exists. Display is accompanied by "beeping"* at the keypad. If this condition persists for more than one day (with AC present), CALL FOR SERVICE. Indicates that there is a low battery condition in the wireless transmitter** number displayed (00 is RF keypad). Accompanied by a single "beep"* (about once every 30 seconds) at the keypad. Either replace the battery yourself, or CALL FOR SERVICE. If the battery is not replaced within 30 days, a CHECK display may occur. Wireless part of the system is experiencing RF interference which may impede reception from wireless sensors.** Indicates a communication problem between the control and a connected device (e.g., RF receiver, zone expander) where the “xx” indicates the device address. CALL FOR SERVICE. Indicates that the control is on-line with the Central Monitoring Station's remote computer. The control will not report system activity while on-line. Wait a few minutes — the display should disappear. Indicates that the wiring connection to the external sounder is at fault (open or shorted). Accompanied by “beeping” at the keypad. CALL FOR SERVICE.

* Any “beeping” that
accompanies a trouble display can be stopped by depressing any key on the keypad or by entering an OFF sequence (code + OFF)

LO BAT + zone descriptor (or BAT with zone No.)

** Not all systems use
wireless sensors.

Rcvr Jam (or CHECK 90) ALARM 1xx FAULT 1xx CHECK 1xx (or 91) MODEM COMM (or CC)

BELL FAILURE (or CHECK 70)

– 43 –

Trouble Conditions (cont’d)
Other Trouble Displays (Continued) AC LOSS (or NO AC) The system is operating on battery power only due to an AC power failure. If only some lights are out on the premises, check circuit breakers and fuses and reset or replace as necessary. If AC power cannot be restored and a “low system battery” message appears (see previous page), CALL FOR SERVICE. If this message remains displayed for more than 1 minute, system is disabled. CALL FOR SERVICE. The keypad is not receiving signals from the control. CALL FOR SERVICE. If part of your system, back-up Long Range Radio communication has failed. CALL FOR SERVICE. The telephone line has a problem. CALL FOR SERVICE.

Busy-Standby (or dI) OPEN CIRCUIT (or OC) Long Rng Trbl (or bF)

TELCO FAULT (or CHECK 94)

Total Power Failure If there is no keypad display at all, and the READY indicator is not
lit, operating power (from AC and back-up battery) for the system has been interrupted and the system is inoperative. CALL FOR SERVICE.

In The Event Of Telephone Operational Problems
In the event of telephone operational problems, disconnect the control from the phone line by removing the plug from the phone wall jack. We recommend that your installer demonstrate this disconnection on installation of the system. Do not attempt to disconnect the phone connection inside the control. Doing so will result in the loss of your phone lines. If the regular phones work correctly after the control has been disconnected from the phone wall jack, the control has a problem and you should immediately call for service. If upon disconnection of the control, there is still a problem on the phone line, notify the Telephone Company that they have a problem and request prompt phone repair service. The user may not under any circumstances attempt any service or repairs to the security system. Repairs must be made only by authorized service (see the LIMITED WARRANTY statement for information on how to obtain service).

– 44 –

Maintaining Your System
Taking Care of Your System
The components of your security system are designed to be as maintenance-free as possible. However, to make sure that your system is in reliable working condition, do the following: 1. Test your system weekly. 2. Test your system after any alarm occurs. You can silence the keypad’s warning tones by pressing the OFF key, but the keypad's low battery message display will remain on as a reminder that you have a low battery condition in one or more of your wireless sensors. When you replace the weak battery with a fresh one, the sensor sends a "good battery" signal to the control as soon as the sensor is activated (opening/closing of door, window, etc.), causing the low battery display to turn off. If the sensor is not activated, the display will automatically clear within approximately 1 hour. Each wireless sensor in your system has a 9-volt or 3-volt battery. The system detects a low battery in wireless sensors, including smoke detectors, the personal emergency transmitter, and the portable wireless keypad and displays a low battery message*. (A low battery in a portable wireless keypad is detected as soon as one of its keys is pressed, and displayed as 00.). Battery-operated smoke detectors with a low battery also emit a single "chirp" sound approximately once every 20–30 seconds. Alkaline batteries provide a minimum of 1 year of operation, and in most units and applications, provide 2–4 years of service. 3-volt lithium batteries provide up to 4 or more years of operation. Actual battery life will depend on the environment in which the sensor is used, the number of signals that the transmitter in the sensor has had to send, and the specific type of sensor. Factors such as humidity, high or low temperatures or large swings in temperature, may all lead to the reduction of actual battery life in an installation. * The low battery message comes on as a warning that battery replacement
in indicated sensor(s) is due within 30 days. In the meantime, a sensor causing a low battery indication is still fully operational.

Silencing Low Battery Warning Tones at the Keypad

Replacing Batteries in Wireless Sensors
Wireless sensors may not have been used in your security system IMPORTANT: Use only batteries recommended by your installer as replacement.

Routine Care • Treat the components of your security system as you would any
other electrical equipment. Do not slam sensor-protected doors or windows. • Keep dust from accumulating on the keypad and all protective sensors, particularly on motion sensors and smoke detectors. • The keypad and sensors should be cleaned carefully with a dry soft cloth. Do not spray water or any other fluid on the units.

– 45 –

Fire Alarm System
THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS
General
Your fire alarm system (if installed) is on 24 hours a day, for continuous protection. In the event of an emergency, the strategically located smoke and heat detectors will sound their alarms and automatically send signals to your system, triggering a loud, interrupted pulsed sound* from the Keypad(s) and any external sounders. A FIRE message will appear at your Keypad and remain on until you silence the alarm (see below for silencing fire alarms). * Temporal pulse sounding is produced for Fire alarms, as follows: 3 pulses–pause–3 pulses–pause–3 pulses–pause. . . , repeated.
TYPICAL FIRE EMERGENCY DISPLAYS

FIRE 01 BEDROOM

MASTER

ALARM FIRE
FIXED-WORD DISPLAY KEYPAD

01

AC

ALPHA DISPLAY KEYPAD

Silencing Fire Alarms and Clearing Memory of Alarm

1.

You can silence the alarm at any time by pressing the OFF key (the security code is not needed to silence fire alarms). To clear the display, enter your code and press the OFF key again (to clear Memory of Alarm).

2. If the Keypad's FIRE display does not clear after the second OFF sequence, smoke detectors may still be responding to smoke or heat producing objects in their vicinity. Investigate, and should this be the case, eliminate the source of heat or smoke. 3. If this does not remedy the problem, there may still be smoke in the detector. Clear it by fanning the detector for about 30 seconds. When the problem has been corrected, clear the display by entering your code and pressing the OFF key.

Smoke Detector Depending on the type of smoke detectors in your system, it may be Reset necessary to "reset" the smoke detectors after a fire alarm has been
turned off. Check with your installer. This "reset" is accomplished at a keypad, as follows: Enter Security Code ( except “arm only” user), then press the [1] key. NOTE: During smoke detector reset, “FAULT xx” appears (about six seconds) and should disappear if the detector is clear.

– 46 –

Fire Alarm System (cont’d)
THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS
Manually 1. Should you become aware of a fire emergency before your smoke or heat detectors sense the problem, go to your nearest keypad and Initiating manually initiate an alarm by pressing the panic key assigned for a Fire Alarm
FIRE emergency for 2 seconds (see below). If a key pair has been assigned for fire, press both keys at the same time. See the Using the Panic Keys section below for further details. 2. Evacuate all occupants from the premises. 3. If flames and/or smoke are present, leave the premises and notify your local Fire Department immediately. 4. If no flames or smoke are apparent, investigate the cause of the alarm. The zone number(s) of the zone(s) in an alarm condition will be displayed at the keypad.

Using the Panic Key(s) Assigned for FIRE Emergency

A key or key pair may have been assigned for manually initiating a FIRE alarm. See the Panic Keys section for key assignments. For convenience, indicate the key or key pair assigned for fire below. In divi dua l Key s A B C
Press the individual key assigned for fire for 2 seconds.

OR Key Pairs 1 OFF and ∗
READY

∗

READY

(zone 95) (zone 99) (zone 96)

and # and #

Press both keys of the key pair assigned for fire at the same time.

3 STAY

DISPLAYS FOLLOWING MANUAL INITIATION OF A FIRE ALARM

FIRE 95
ALPHA DISPLAY KEYPAD

ALARM FIRE
FIXED-WORD KEYPAD

95

AC

Carbon If installed, carbon monoxide detectors provide continuous protection. Monoxide If a high level of carbon monoxide is detected, an interrupted pulsed Alarms alarm sound occurs at the keypads and the detector(s). Immediately
move to a spot where fresh air is available, preferably outdoors. From a safe area, call your security service provider for further instructions. To silence the keypad sounding, press the OFF key. To silence the detector, see its instructions.

– 47 –

Fire Alarm System (cont’d)
THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS

National Fire Protection Association Recommendations on Smoke Detectors
With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's National Fire Alarm Code (NFPA 72) noted below. Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows: A smoke detector installed outside of each separate sleeping area, in the immediate vicinity of the bedrooms and on each additional story of the family living unit, including basements and excluding crawl spaces and unfinished attics. In addition, the NFPA recommends that you install heat or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached garages.
KITCHEN DINING
KITCHEN DINING BDRM

BEDROOM BEDROOM

TV ROOM

LIVING ROOM BDRM BEDROOM

LIVING ROOM

BEDROOM

Smoke Detectors for Minimum Protection Smoke Detectors for Additional Protection BEDROOM TO BR Heat-Activated Detectors

BEDROOM

BEDROOM KTCHN

LVNG RM BASEMENT

.

CLOSED DOOR

GARAGE

floor_plan-001-V1

– 48 –

Fire Alarm System (cont’d)
THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS

Emergency Evacuation
OS ET BE OO DR M

CL
PORCH

BE

OO DR

M

TH BA

BE

OO DR

M

2nd FLOOR

TC KI BACK DOOR

HE

N BE

OO DR

M

BE

OO DR

M

TH BA

1st FLOOR

BACK

FRONT

Establish and regularly practice a plan of escape in the event of fire. The following steps are recommended by the National Fire Protection Association: 1. Position your detector or your interior and/or exterior sounders so that they can be heard by all occupants. 2. Determine two means of escape from each room. One path of escape should lead to the door that permits normal exit from the building. The other may be a window, should your path be impassable. Station an escape ladder at such windows if there is a long drop to the ground. 3. Sketch a floor plan of the building. Show windows, doors, stairs and rooftops that can be used to escape. Indicate escape routes for each room. Keep these routes free from obstruction and post copies of the escape routes in every room. 4. Assure that all bedroom doors are shut while you are asleep. This will prevent deadly smoke from entering while you escape. 5. Try the door. If the door is hot, check your alternate escape route. If the door is cool, open it cautiously. Be prepared to slam the door if smoke or heat rushes in. 6. When smoke is present, crawl on the ground. Do not walk upright, since smoke rises and may overcome you. Clearer air is near the floor. 7. Escape quickly; don't panic. 8. Establish a common meeting place outdoors, away from your house, where everyone can meet and then take steps to contact the authorities and account for those missing. Choose someone to assure that nobody returns to the house — many die going back.

floor_plan-002-V0

– 49 –

Quick Guide to Basic System Functions
FUNCTION
Check Zones Arm System

PROCEDURE
Press READY key.

COMMENTS
View faulted zones when system not ready.

Enter code. Press arming key desired: Arms system in mode selected. (AWAY, STAY, NIGHT-STAY, MAXIMUM, INSTANT) Press #. Press arming key desired: (AWAY, STAY, MAXIMUM, INSTANT) Enter code. Press BYPASS [6] key. Enter zone number(s) to be bypassed (use 2-digit entries). Enter code. Press BYPASS [6] key + [#]. Arms system in mode selected, quickly and without use of a code. Bypassed zones are unprotected and will not cause an alarm if violated. Bypasses all faulted zones automatically. Also disarms system. Memory of alarm remains until cleared. Memory of Alarm remains until cleared. Determine cause. Also silences sounders. Memory of alarm remains until cleared. Keypad beeps rapidly on entry if alarm has occurred while absent. Alarm display will remain upon disarming until cleared. Performs desired action and sends silent alarm to Central Station. See the Panic Keys section for emergency functions programmed for your system. Note: Keys “A”, “B”, and “C” may have been programmed for other functions. The keypad will sound if doors or windows are violated while system is disarmed and chime mode is ON. Tests alarm sounder and allows sensors to be tested. Permits system access remotely, via Touch-tone phone.

Quick Arm (if programmed) Bypass Zone(s)

Quick Bypass (if programmed) Silence Sounders Burglary: Fire or CO: "Check": Disarm System

Enter code. Press OFF [1] key. Press OFF [1] key. Press any key. Enter code. Press OFF [1] key. (OFF need not be pressed if entry delay or an alarm is active) After disarming, enter code again. Press OFF [1] key again.

Clear Alarm Memory

Duress (if active and connected to Central Station) Panic Alarms (as programmed)

Arm or disarm "normally," but use your 4digit Duress code to do so. Press key [A], [B], or [C] for at least 2 seconds, or key pairs 1 + ✱; ✱ + #, or 3 + #
respectively.

Chime Mode

To turn ON or OFF: Enter code. Press CHIME key. To turn ON: Enter code. Press TEST key, then [0]. To turn OFF: Enter code. Press OFF key. Consult Phone Access User's Guide that accompanies the Phone Module.

Test Mode

Phone Access if applicable

– 50 –

Summary of Audible/Visual Notifications
Fixed-Word Display Keypads
SOUND CAUSE DISPLAY
LOUD, FIRE ALARM or CO ALARM (CO: FIRE or ALARM (for CO) is displayed; zone INTERRUPTED* keypad/detector only; not external number of zone in alarm is displayed. If a fire sounder) alarm is manually activated, zone number 95 Keypad & Ext. will be displayed. LOUD, CONTINUOUS* Keypad & Ext. ONE SHORT BEEP (not repeated) Keypad only BURGLARY/AUDIBLE EMERGENCY ALARM a. SYSTEM DISARM b. SYSTEM ARMING ATTEMPT WITH AN OPEN ZONE c. BYPASS VERIFY ALARM is displayed. Zone number of zone in alarm is also displayed. a. READY indicator light comes on. b. Number of the open protection zone displayed. c. Zone numbers of the bypassed protection zones are displayed (one beep is heard for each zone displayed). Subsequently, BYPASS is displayed. a. Opened zone numbers will appear. b. BAT displayed with zone number of transmitter. c. No special display. AWAY is displayed. Red ARMED indicator is lit. a. STAY or INSTANT is displayed. Red ARMED indicator is lit. b. CHIME displayed; zone number of open protection zone will be displayed if the [✱] key is pressed. a. CHECK displayed. Zone number of troubled protection zone is displayed. b. FIRE or ALARM is displayed; zone number of zone in alarm is displayed c. BAT displayed with no zone ID number. d. CHECK 70 is displayed. e. No special display. a. AWAY is displayed. b. Exceeding the entry delay time without disarming causes alarm.

ONE SHORT BEEP (once every 40 secs) Keypad only TWO SHORT BEEPS Keypad only THREE SHORT BEEPS Keypad only

a. SYSTEM IS IN TEST MODE b. LOW BATTERY AT A TRANSMITTER c. SYSTEM WILL AUTOARM WITHIN 10 MINUTES ARM AWAY or MAXIMUM

a. ARM STAY, NIGHT-STAY, INSTANT b. ZONE OPENED WITH SYSTEM IN CHIME MODE a. TROUBLE b. MEMORY OF ALARM c. SYSTEM LOW BATTERY d. EXT. SOUNDER WIRING FAIL e. LAST 10 SEC of EXIT DELAY

RAPID BEEPING Keypad only

SLOW BEEPING Keypad only

a. EXIT DELAY WARNING b. ENTRY DELAY WARNING

* If a bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady ring.

– 51 –

Summary of A/V Notifications (cont’d)
Alpha Display Keypads
SOUND CAUSE DISPLAY
FIRE or ALARM (for CO) is displayed; descriptor of zone in alarm is displayed. If a fire alarm is manually activated, zone number 95 will be displayed. ALARM is displayed. If programmed, descriptor of zone in alarm is also displayed a. DISARMED/READY TO ARM is displayed. b. Number and descriptor of open protection zone is displayed. c. Numbers and descriptors of the bypassed zones are displayed (One beep is heard for each zone displayed). Then, the following is displayed: DISARMED BYPASS /Ready to Arm. a. Opened Zone identifications will appear. b. LO BAT displayed with description of transmitter. c. No special display. ARMED AWAY or MAXIMUM displayed. Red ARMED indicator lit. a. ARMED STAY or ARMED INSTANT displayed. Red ARMED indicator lit. b. CHIME displayed, descriptor of open protection zone will be displayed if the [✱] key is pressed. LOUD, FIRE ALARM or CO ALARM INTERRUPTED* (CO: keypad/detector only; not Keypad & Ext. external sounder) LOUD, CONTINUOUS* Keypad & Ext. ONE SHORT BEEP (not repeated) Keypad only BURGLARY/AUDIBLE EMERGENCY ALARM a. SYSTEM DISARM b. SYSTEM ARMING ATTEMPT WITH AN OPEN ZONE c. BYPASS VERIFY

ONE SHORT BEEP (once every 40 seconds) Keypad only TWO SHORT BEEPS Keypad only THREE SHORT BEEPS Keypad only

a. SYSTEM IS IN TEST MODE b, LOW BATTERY AT A TRANSMITTER c. SYSTEM WILL AUTOARM WITHIN 10 MINUTES ARM AWAY or MAXIMUM

a. ARM STAY, NIGHT-STAY, OR INSTANT b. ZONE OPENED WHILE SYSTEM IS DISARMED a. TROUBLE

RAPID BEEPING Keypad only

a. CHECK displayed. Descriptor of troubled protection zone is displayed. b. MEMORY OF ALARM b. FIRE or ALARM is displayed; descriptor of zone in alarm is displayed. c. SYSTEM LOW BATTERY. d. EXT. SOUNDER WIRE FAIL c. SYSTEM LO BAT displayed. d. BELL FAILURE is displayed. e. LAST 10 SEC of EXIT DELAY e. No special display. a. EXIT DELAY WARNING (if programmed). b. ENTRY DELAY WARNING. a. ARMED AWAY or MAXIMUM is displayed along with You May Exit Now. b. DISARM SYSTEM OR ALARM WILL OCCUR is displayed. Exceeding the delay time without disarming causes an alarm.

SLOW BEEPING Keypad only

* If a bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady ring.

– 52 –

Regulatory Statements and Warnings
FEDERAL COMMUNICATIONS COMMISSION (FCC) PART 15 STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA (IC) STATEMENTS This device complies with RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

TELEPHONE/MODEM INTERFACE
FCC Part 68
This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains the FCC registration number and Ringer Equivalence Number (REN). You must provide this information to the telephone company when requested. This equipment uses the following USOC jack: RJ31X This equipment may not be used on telephone-company-provided coin service. Connection to party lines is subject to state tariffs. This equipment is hearing-aid compatible.

Industry Canada
NOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

– 53 –

Regulatory Statements (cont’d)
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together, This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves but should contact appropriate electric inspection authority, or electrician, as appropriate.

Ringer Equivalence Number Notice:
The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

Industrie Canada
AVIS: l’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur. Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’enterprise locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée da raccordement. L’abonné ne doit pas oublier qu’il est possible que la conformité aux conditions énoncées ci-dessus n’empêche pas la dégradation du service dans certaines situations. Les réparations de matériel nomologué doivent être coordonnées par un représentant désigné par le fournisseur. L’entreprise de télécommunications peut demander à l’utilisateur da débrancher un appareil à la suite de réparations ou de modifications effectuées par l’utilisateur ou à cause de mauvais fonctionnement.

Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’energie
électrique, de lignes téléphoniques et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales. Avertissement : L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir racours à un service d’inspection des installations électriques, ou à un électricien, selon le cas. AVIS : L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.

– 54 –

System Features Log
Features
Exit Delay Entry Delay 1 Entry Delay 2 NIGHT-STAY Zones Quick Arm Quick Bypass Automatic Paging Keyswitch Arming (circle type of LED lighting)

Comments Part. 1: Part. 1: Part. 1: Zones: yes yes yes Arm AWAY: Arm STAY: A B C no no no steady steady D users: flash flash Part. 2: Part. 2: Part. 2:

Function Keys
• Single-Button Arming • Step Arming • Paging (see Paging chart) • Time/Date Display • Macro Key 1 • Macro Key 2 • Macro Key 3 • Macro Key 4 • Emergency Key**: Personal • Emergency Key**: Silent Alarm • Emergency Key**: Audible Alarm • Emergency Key**: Fire • Device Activation

Comments

Device: A = [1] / [∗] B = [∗] / [#] C = [3] / [#]

** Emergency Keys:

– 55 –

System Features Log (cont’d)
User Setup
The following chart will help keep track of system users. Copies should be distributed to the partition 1 and partition 2 (if applicable) masters for their records. To program a user attribute: Enter system/partition* master code + [8] + user no. + “#” command listed in column heading.
User No. User Name User’s Part(s).
(system master only)
[#] [3] + part(s) + [#]

Security Code
enter new code

Auth. Level
[#] [1] + level

Access Group
[#] [2] + group

RF Zone Number
[#] [4] + zone no.

Pager on/off
[#] [5] + 0/1

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

installer system master partition 1 master

(all) (all) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1)

installer master (4) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0)

(1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1)

– 56 –

System Features Log (cont’d)
User Setup (cont’d)
Enter system/partition master code + [8] + user no. + “#” command listed in column heading.
User No.* User Name User’s Part(s).
(system master only)
[#] [3] + part(s) + [#]

Security Code
enter new code

Auth. Level
[#] [1] + level

Access Group
[#] [2] + group

RF Zone Number
[#] [4] + zone no.

Pager on/off
[#] [5] + 0/1

33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49

partition 2 master

(2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2) (2)

(4) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0) (0)
Partitions: 0 = clears partition 1 and partition 2 defaults 1 = partition 1 and common 2 = partition 2 and common 3 = common partition only Paging: 0 = no paging; 1 = allow paging

(1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1) (1)

Authority Levels: 0 = standard user 1 = arm only 2 = guest 3 = duress 4 = partition master

Paging Setup
Pager 1 2 3 4 Pager Phone Number\ Prefix Characters Automatically Reports Upon… open/close alarm/trouble zone list p1 p2 p1 p2 p1 p2 Sched. Func. Key

– 57 –

System Features Log (cont’d)
Schedules*: master code + [#] + [6] [4]
No. Event
(see list below)

Device No.
for “01” events:

Group No.
for “02” events:

Partition
for “04-06” events: enter 1, 2, or 3

(see device list below) enter 1-8

Start Time/ Day

Stop Time/ Day

Repeat
(1-4)

Random
(yes/no)

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16
00 = clear event 03 = latch key report 06 = auto disarm 01 = device on/off 04 = forced STAY arm 07 = display “reminder” 02 = user access 05 = forced AWAY arm Repeat Options: 0 = none; 1 = repeat weekly; 2 = repeat every other week; 3 = repeat every third week; 4 = repeat every fourth week Events:

List of Output Devices
Device 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 Description Schedule No. Function Key

– 58 –

OWNER’S INSURANCE PREMIUM CREDIT REQUEST
This form should be completed and forwarded to your homeowner’s insurance carrier for possible premium credit.

A. GENERAL INFORMATION:
Insured’s Name and Address:

Insurance Company:

Policy No.:

VISTA-21iP / VISTA-21iPSIA ________________________________________________ Other
(circle the appropriate model number)

Type of Alarm:

Burglary

Fire

Both

Installed by:
Name Address

Serviced by:
Name Address

B. NOTIFIES (Insert B = Burglary, F = Fire) Local Sounding Device Police Dept. Central Station Name: Address: Phone: C. POWERED BY: A.C. With Rechargeable Power Supply D. TESTING: Quarterly Monthly Weekly

Fire Dept.

Other

continued on other side

– 59 –

OWNER’S INSURANCE PREMIUM CREDIT REQUEST (cont.)
E. SMOKE DETECTOR LOCATIONS Furnace Room Basement Kitchen Living Room Bedrooms Dining Room Attic Hall

F. BURGLARY DETECTING DEVICE LOCATIONS: Front Door 1 Floor Windows
st

Basement Door All windows

Rear Door
Interior locations

All Exterior Doors

All Accessible Openings, Including Skylights, Air Conditioners and Vents G. ADDITIONAL PERTINENT INFORMATION:

Signature:

Date:

– 60 –

– Notes –

– 61 –

– Notes –

– 62 –

LIMITATIONS OF THIS SYSTEM
WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example: • Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. • Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. • Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. • A user may not be able to reach a panic or emergency button quickly enough. • While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death. • Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90° to 105°F, the detection performance can decrease. • Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers. • Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. • Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. • This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments.

– 63 –

TWO YEAR LIMITED WARRANTY
Honeywell International Inc., acting through its Security & Communications business (“Seller”), 2 Corporate Center Drive, Melville, New York 11747 warrants its products to be free from defects in materials and workmanship under normal use and service, normal wear and tear excepted, for 24 months from the manufacture date code; provided, however, that in the event the Buyer presents a proper invoice relating to the purchased product and such invoice bears a date later than the manufacture date, then Seller may at its discretion, reflect the warranty period as commencing at invoice date. Except as required by law, this Limited Warranty is only made to Buyer and may not be transferred to any third party. During the applicable warranty period, Seller will repair or replace, at its sole option and as the exclusive remedy hereunder, free of charge, any defective products. Seller shall have no obligation under this Limited Warranty or otherwise if the product: (i) is improperly installed, applied or maintained; (ii) installed outside of stated operating parameters, altered or improperly serviced or repaired by anyone other than the Seller/Seller’s Authorized Service/Repair Center; (iii) damage is caused by outside natural occurrences, such as lightning, power surges, fire, floods, acts of nature, or the like; or (iv) defects result from unauthorized modification, misuse, vandalism, alterations of serial numbers, other causes unrelated to defective materials or workmanship, or failures related to batteries of any type used in connection with the products sold hereunder. Exceptions to Warranty With Respect to Honeywell Products listed below: Hardwire Contacts and PIRs – Seller warrants parts for hardwire contacts and PIRs in accordance with the terms of the above limited warranty for a period of five (5) years from the manufacture date code. EXCLUSION OF WARRANTIES, LIMITATION OF LIABILITY THERE ARE NO WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. TO THE FULL FULLEST EXTENT PERMITTED BY LAW, IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY (i) CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES ARISING OUT OF OR RELATING IN ANY WAY TO THE PRODUCT AND/OR FOR BREACH OF THIS OR ANY OTHER WARRANTY OR CONDITION, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY SELLER’S OWN NEGLIGENCE OR FAULT AND EVEN IF SELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES OR DAMAGES. Any product description (whether in writing or made orally by Seller or Seller’s agents), specifications, samples, models, bulletin, drawings, diagrams, engineering sheets or similar materials used in connection with the Buyer’s order are for the sole purpose of identifying the Seller’s products and shall not be construed as an express warranty or condition. Any suggestions by Seller or Seller’s agents regarding use, applications, or suitability of the products shall not be construed as an express warranty or condition unless confirmed to be such in writing by Seller. Seller does not represent that the products it sells may not be compromised or circumvented; that the products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise, or that the products will in all cases provide adequate warning or protection. Buyer understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery or fire without warning, but it is not insurance or a guarantee that such will not occur or will not cause or lead to personal injury or property loss. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE ORF OTHER LOSS BASED ON ANY CLAIM AT ALL INCLUDING A CLAIM THE PRODUCT FAILED TO GIVE WARNING. However, if Seller is held liable whether directly or indirectly for any loss or damage with respect to the products it sells, regardless of cause or origin, its maximum liability shall not in any case exceed the purchase price of the product, which shall be fixed as liquidated damages and not as a penalty, and shall be the complete and exclusive remedy against the Seller. Should your product become defective during the warranty, please contact your installer to facilitate repair or replacement with Seller pursuant to the terms hereof. Seller reserves the right to replace any defective product under warranty with new, refurbished, or remanufactured product.

2 Corporate Center Drive, Suite 100 P.O. Box 9040 Melville, NY 11747 Copyright © 2007 Honeywell International Inc. www.honeywell.com/security

ÊK14490V1:Š
K14490V1 7/10 Rev. A