Interlogix Concord 4 - Install Guide



Related Categories


Document Transcript


Concord 4 Installation Manual


P/N 466
-2182

• REV
K


ISS
11AUG
16 Copyright


©

201
6
UTC Fire & Security Americas Corporation, Inc.

Interlogix is part of UTC Climate Controls & Security, a unit of United Technologies
Corporation.


All rights reserved.

This document may not be copied in whole or in part or otherwise reproduced without prior
written consent from
UTC Fire &

Security, Inc., except where specifically permitted under US
and international copyright law.

Disc
laimer


The information in this document is subject to change without notice.
UTC Fire &
Security
assumes no responsibility for inaccuracies or omissions and specifically disclaims any
liabilities, losses, or risks, personal or otherwise, incurred as a con
sequence, directly or
indirectly, of the use or application of any of the contents of this document. For the latest
documentation, contact your local supplier or visit us online at
www.utcfireandsecurity.com
.

Thi
s publication may contain examples of screen captures and reports used in daily
operations. Examples may include fictitious names of individuals and companies. Any
similarity to names and addresses of actual businesses or persons is entirely coincidental.

Trademarks and
patents


Other trade names used in this document may be trademarks or registered trademarks of the
manufacturers or vendors of the respective products.

Intended use


Use this product only for the purpose it was designed for; refer to the d
ata sheet and user
documentation for details. For the latest product information, contact your local supplier or
visit us online at

www.utcfireandsecurity.com
.

Contact information


www.utcfireandsecurity.com
. or
www.interlogix.com

Technical support



www.interlogix.com/customer
-
support
.


Concord 4 Installation Manual

i

Content

Impo
rtant information
iii

Chapter

1

Introduction

1

Planning the installation
2

SuperBus 2000 bus devices
3

Chapter

2

Installation

5

Installation overview
6

Mounting the panel
10

Intrusion detection devices
15

Smoke detectors
15

Speakers and sirens
18

SuperBus 2000 touchpads
22

SuperBus 2000 modules
22

Phones
28

Power
30

Ch
apter

3

Programming

33

Overview
34

Quick programming mode
36

Tier 1 programming menus
37

Tier 2 programming menus
40

Security menu
45

Phones menu
50

Phone options menu
54

Timers menu
57

Light control menu
59

Touchpad options menu
60

Reporting menu
61

Siren options menu
66

Sensors menu
67

Audio verification menu
71

Accessory modules menu
73

Onboard options menu
78

Macro keys menu
81

User programming mode
82

Downlo
ader programming
93

Chapter

4

Testing and troubleshooting

95

Testing the system
96

ii

Concord 4 Installation Manual

Troubleshooting
106

Appendix

A

System plannin
g sheets

117

Customer information
118

Wireless devices
118

Hardware devices
119

Zone and sensor assignments
121

System settings index and record
124

Appendix

B

Reference tables

129

Sensor group characteristics
130

Sensor text
134

System event triggers
136

Sensor group event triggers
137

Sensor number event triggers
138

System feature event triggers
141

Response characteristics
143

Response numbers
143

Specifications
145


Concord 4 Installation Manual

iii
Important information

Intended use

Use this product only for the purpose it was desig
ned for; refer to the data sheet
and user documentation for details. For the latest product information, contact
your local supplier or visit us online at
www.utcfireandsecurity.com
.
Changes or modifications not
expressly approved by UTC Fire & Security can
void the user’s authority to operate the equipment.

About this manual

This manual provides information for planning, installing, programming, and
testing this security system. Planning sheets are included for y
ou to record
hardware layout and software programming settings.

Use this manual for the following panels:


600
-
1021
-
95R

Concord 4 RF

600
-
1022
-
95R

Concord Express V4

600
-
1040

Concord Commercial V4

600
-
1042

Concord Hybrid


When necessary, this manual ref
ers you to other documentation with compatible
peripherals.

The
Concord 4 User Manual
(P/N 466
-2183) contains user worksheets that you
should fill out during the installation and programming of the system. For
multiple
-partition systems, we suggest a user
manual for each partition.

Read these instructions and all related documentation entirely before installing or
operating this product.

Note:
A qualified service person, complying with all applicable codes, should
perform all required hardware installation
.


Concord 4 Installation Manual

1

Chapter

1

Introduction

Summary

This chapter provides information to help you plan your Concord 4 panel and
system installation.

Content

Planning the installation


2

Standard panel

2

SuperBus 2000 bus devices

3

Chapter 1
:
Introduction

2

Concord 4 Installation Manual

Planning the installation

This section describes system capabilities to help you get familiar with the
system.

Appendix

A


System planning sheets

on page 117

provides planning
sheets that let you record the hardware and programming configuration of the
system. F
ill in all necessary information ahead of time to help prepare for system
installation.

Standard panel

Table

1

below

shows the standard panel capabilities.

Table

1
: P
anel capabilities

Capabilities

Concord Express v4

Concord 4/Concord Commercial
v4

Zones

32

96

Partitions

2

6

Bus devices

16

16

User codes

16

230


Table

2

describes the basic panel (out
-
of
-
box) hardware capabilities

for all
panels.

Table

2
: Basic panel hardware capabilities

Power

Input for an AC step
-
down, plug
-
in style transformer.

Auxiliary power output

Output that supplies 9 to 14 VDC with up to 1 amp for bus devices
and hardwired detector
s, such as smoke and motion detectors.

Bus A and B

Input and output that provides communication between bus devices
and the panel.

Siren driver

Output that can drive an 8
-
ohm load and provides intrusion and fire
alarm sounds for partition 1 (15 watts max
imum).

Two onboard outputs

Can be used to activate other signaling devices based on system
events.

Out 1 is a 9 to 14 VDC source output, limited to 1.0 amp max.

Out 2 is an open
-
collector output, rated up to 14 VDC, 300 mA max

Microphone input

Input used

for 2
-
way audio when used in conjunction with the
Interrogator 200 audio verification module.

Eight supervised hardwired
zones

Inputs for various hardwired detectors. Zone 8 can be set up in
programming to accept two
-
wire smoke detectors. It sources 9 to

14
VDC, 90mA max.

Chapter 1
:
Intr
oduction

Concord 4 Installation Manual

3

Built
-
in RF receiver

Allows use of up to 96 (Concord 4) or 32 (Concord Express v4)
319.5 MHz. crystal and/or SAW learn mode wireless sensors and
touchpads.

Phone line connection

Allows panel to communicate with central monitoring stati
on and/or
pagers.

SuperBus 2000 bus devices

The following components can be used with the Concord 4 panel:

Table

3
: SuperBus devices

Touchpads

Use the following touchpads for installer/user programming
and system operation.



Super
Bus 2000 2x16 LCD touchpad



SuperBus 2000 2x20 LCD touchpad



SuperBus 2000 2x20 VFD touchpad



SuperBus 2000 ATP 1000 touchpad



SuperBus 2000 ATP 2100 touchpad



SuperBus 2000 ATP 2600 touchpad

Use the following touchpads for installer quick programming
,
system operation and user programming:



SuperBus 2000 fixed display touchpad



SuperBus 2000 FTP 1000 touchpad

SuperBus 2000 RF transceiver

Use the transceiver to receive signals from sensors and
touchpad that may be on the fringe of panel reception. T
he
transceiver is compatible with all 319.5 MHz crystal and SAW
learn mode wireless sensors and touchpads.

Power line carrier transformer

Allows the use of X10 powerhouse lamp modules for light
control and light activation during alarms.

SuperBus 2000 vo
ice only
module

Provides an output for a speaker that sounds system status
and alarm voice messages.

SuperBus 2000 phone
interface/voice module

Allows system access and control using touchtone
telephones, onsite or offsite. The module includes an output
f
or a speaker that sounds system status and alarm voice
messages
Chapter 1
:
Introduction

4

Concord 4 Installation Manual

SnapCards

The following SnapCards expand the system as described:

8Z input Snapcard: Provides eight additional hardwired zone
inputs, of which two are dedicated for using two
-
wire smoke
detec
tors.

4 output SnapCard: Provides four form C relay outputs that
can be set up to activate other signaling devices, based on
system events, schedules, or direct control.

4Z input/output combo SnapCard: Provides three hardwired
zone inputs, one two
-
wire smo
ke detector loop, and two
outputs that can be set up to activate other signaling devices,
based on system events, schedules, or direct control.

SuperBus 2000 8Z input
module (HIM)

Provides eight additional hardwire zone inputs.

SuperBus 2000 four
-
relay
o
utput module (HOM)

Provides four form C relay outputs that can be set up to
activate other signaling devices, based on system events.

Interrogator 200 audio
verification module

Allows central station operators to listen in and talk to
occupants on the pre
mises to verify the emergency when an
alarm report is received.

SuperBus 2000 energy saver
module (ESM)

Provides a money
-
saving and convenient way to monitor and
control temperatures. The ESM uses low
-

and high
-
temperature limits to save energy by overrid
ing the existing
HVAC thermostat.

SuperBus 2000 automation
module

Provides a connection to a compatible home automation
device.

SuperBus 2000 wireless
cellular gateway

Allows users to control and monitor the status of their system
from the alarm.com inte
rnet website.

SuperBus 2000 2
-
amp power
supply

Provides an additional 12 VDC, 2 amps for powering system
devices and is supervised via the panel data bus.



Concord 4 Installation Manual

5

Chapter

2

Installation

Summary

This chapter provides information on lo
cating and installing the panel and system
components.

Content

Error! Bookmark not defined.
Chapter 2
:
Installation

6

Concord 4 Installation Manual

Installation overview

Before starting the installation, plan your system layout and programming using
th
e worksheets provided in
Appendix

A


System planning sheets

on page 117
.

Note:
Class 2, Class 3, and power
-
limited fire alarm circuits must be installed

using FPL, FPLR, FPLP, or substitute cable permitted by the National Electrical
Code ANSI/NFPA 70 or Class 2, Class 3, and power
-
limited fire alarm circuit
conductors must be installed as Class 1 or higher circuits.

Note:
Class 2, Class 3, and power
-
limit
ed burglar alarm circuits must be installed
using CL2, CL2R, CL2P, or substituting cable permitted by ANSI/NFPA 70. Wire
that extends beyond the cable jacket must be separated from all other
conductors by a minimum of 0.25 in. or by a nonconductive barrier
.

Use the following installation guidelines:



Centrally locate the panel with relation to detection devices whenever
possible, to help reduce wire run lengths and labor.



Locate the panel where the temperature will not exceed 120°F (49°C) or fall
below 3
2°F (0°C).



Avoid running wires parallel with electrical wiring or fixtures such as
fluorescent lighting, to prevent wire runs from picking up electrical noise.



Mount the panel at a comfortable working height (about 45 to 55 in. from the
floor to the bo
ttom of the panel, as shown in
Figure

1

on page 7
).



Leave space to the left and right of the panel for wiring, phone jack, and
mounting optional modules. Allow at least 9 in. (23 cm) above

the panel
cabinet for antennas. Allow at least 24 in. (62 cm) in front of the panel to open
the panel door.

Chapter 2
:
Installation

Concord 4 Installation Manual

7

Figure

1
: Panel and component locations on a wall


Total system power and wire length guidelines

The panel can supply up
to 1 amp (1,000 mA) in full load alarm condition for
system devices connected to panel terminals 4 (+12V), 7 and 8 (speaker
terminals), 9 (OUT1), 11 (+12V), 24 (2W SMK ZONE 8), and SnapCard
terminals.

For 24
-
hour backup, the total standby current draw for
all devices connected to
panel terminals 4 (+12V), 9 (OUT1), 11 (+12V), 24 (if configured for 2
-
wire
smoke loop), and SnapCard terminals is limited to 90 mA (during normal standby
condition) using a 4.5 or 5.0 Ah battery, or 190 mA (during normal standby
c
ondition) using a 7.0 Ah battery.

The total system wire length allowed can vary depending on devices powered by
the panel, the wire length between devices and the panel, and the combined wire
length of all devices.
Chapter 2
:
Installation

8

Concord 4 Installation Manual

Table

4

below

describes the maximum wire length allowed between compatible
devices and the panel, and the minimum and maximum current draw of each
device.

Table

4
: Wire length requirements

Device

Max. wi
re
length to
panel

Standby mA
draw

Alarm mA draw

SuperBus 2000 2x16 LCD alphanumeric
touchpad

22 ga.: 300 ft.

18 ga.: 750 ft.

15 mA

90 mA

SuperBus 2000 ATP 1000 alphanumeric
touchpad

22 ga.: 300 ft.

18 ga.: 750 ft.

12 mA

110 mA

SuperBus 2000 ATP 2100 al
phanumeric
touchpad

22 ga.: 300 ft.

18 ga.: 750 ft.

30 mA

165 mA

SuperBus 2000 ATP 2600 alphanumeric
touchpad

22 ga.: 300 ft.

18 ga.: 750 ft.

30 mA

165 mA

SuperBus 2000 fixed display touchpad

22 ga.: 300 ft.

18 ga.: 700 ft.

11 mA

65 mA

SuperBus 2000 FTP

1000 fixed display
touchpad

22 ga.: 300 ft.

18 ga.: 700 ft.

12 mA

75 mA

SuperBus 2000 RF transceiver

22 ga.: 1,000
ft.

18 ga.: 2,500
ft.

45 mA

55 mA

SuperBus 2000 phone interface/voice module

22 ga.: 40 ft.

18 ga.: 120 ft.

25 mA

600 mA

SuperBus 2000 vo
ice
-
only module

22 ga.: 40 ft.

18 ga.: 120 ft.

20 mA

300 mA (jumper)

600 mA (no
jumper)

SuperBus 2000 2 amp power supply


No load

No load

4 input/2 output SnapCard

N/A

20 mA

185 mA*

8Z hardwired zone expander SnapCard

N/A

38 mA

230 mA*

4 output SnapCar
d

N/A

1 mA

130 mA*

SuperBus 2000 8Z input module

22 ga.: 1,800
ft.

18 ga.: 4,000
ft.

18 mA

35 mA

SuperBus 2000 4
-
relay output module

22 ga.: 350 ft.

18 ga.: 900 ft.

12 mA

180 mA

Chapter 2
:
Installation

Concord 4 Installation Manual

9

Device

Max. wi
re
length to
panel

Standby mA
draw

Alarm mA draw

SuperBus 2000 energy saver module

22 ga.: 1,600
ft.

18 ga.: 4,000
ft.

20
mA

20 mA

SuperBus 2000 automation module

22 ga.: 1,500
ft.

18 ga.: 4,000
ft.

30 mA

35 mA

SuperBus 2000 wireless cellular gateway

22 ga.: 40 ft.

18 ga.: 90 ft.

65 mA

1600 mA

Interrogator 200

22 ga.: 3,200
ft.

18 ga.: 4,500
ft.

10 mA

10 mA

Interrogator A
VM

22 ga.: 110 ft.

18 ga.: 260 ft.

45 mA

300 mA

Two
-
wire smoke detectors (ESL 429AT,
429C, 429CT, 521B, 521BXT, 521NCSXT

22 ga.: 330 ft.

18 ga.: 330 ft.

70 μA

60 mA

Two
-
wire smoke detectors (system sensor
2400, 2400TH)

22 ga.: 330 ft.

18 ga.: 330 ft.

120

μA

80 mA

Hardwired interior siren (13
-
949)

22 ga.: 750 ft.

18 ga.: 1,500
ft.

0 mA

85 mA

Piezo dynamic exterior siren (13
-
950)

22 ga.: 750 ft.

18 ga.: 1,500
ft.

0 mA

150 mA

Speaker siren (60
-
528 or 13
-
060)

18 ga.: 100 ft.

0 mA

500 mA

*Maximum current d
raw for the SnapCards does not include the load which may be applied to
their auxiliary DC supply.


Table

5

below

describes the total system wire lengths allowed for all SuperBus
2000 devic
es when installing systems using unshielded or shielded cable. After
determining panel location, run all necessary wires to that location using the
information in
Table

6

on page 1
0
.

Table

5
: Wire lengths

Wire type

Total system wire

18
-
gauge, unshielded

18
-
gauge, shielded

4,000 ft.

3,000 ft.
Chapter 2
:
Installation

10

Concord 4 Installation Manual

Wire type

Total system wire

22
-
gauge, unshielded

22
-
gauge, shielded

4,000 ft.

3,000 ft.

Table

6
: Device wire requirements

Device

Wire r
equirements

AC power transformer

2
-
conductor, 18
-
gauge, 25 ft. max.

Earth ground

Single conductor, 16
-
gauge solid, 25 ft. max.

Telephone (RJ
-
31X)

4
-
conductor

Detection devices

2
-

or 4
-
conductor, 22
-
gauge, 1,000 ft. max.

2
-

or 4
-
conductor, 18
-
gauge, 2,
500 ft. max.

(based on 30 ohms max. loop resistance
including device)

Speakers

2
-
conductor, 18
-
gauge, 100 ft. max.

SuperBus 2000 devices

4
-
conductor, 22
-

or 18
-
gauge

Interrogator 200 AVM power and microphone

4
-
conductor, 22
-
gauge, shielded

2
-
wire smok
e detectors

2
-
conductor, 22
-
gauge, 330 ft. max.

2
-
conductor, 18
-
gauge, 830 ft. max.

Mounting the panel

Mount the panel to the wall or wall studs.

Caution:
Make sure you are free of static electricity whenever you work on the
panel with the cover open. To
discharge any static, first touch the metal panel
chassis, and then stay in contact with the chassis when touching the circuit
board. We recommend using a grounding strap.

To mount the panel:

1
.

Remove the panel door and remove the necess
ary wiring knockouts. Be
careful not to damage the circuit board.

2
.

Feed all wires through wiring knockouts and place the panel in position
against the wall.

3
.

Level the panel and mark the top and bottom mounting holes (se
e
Figure

2

on
page 11
).

4
.

Install anchors where studs are not present.

Chapter 2
:
Installation

Concord 4 Installation Manual

11

5
.

Partially insert screws into the two top mounting hole locations, then hang the
panel on

the two screws.

6
.

Recheck for level, insert the two lower screws, and tighten all four mounting
screws.

Figure

2
: Panel components and mounting holes

Mounting hole
Backup battery terminals
Programming
touchpad header
Mounting hole
Antennas
Mounting hole
Snapcard connector
Processor
T
erminal strip
Mounting hole

Grounding the panel

For maximum protection from lightning str
ikes and transients, connect the
enclosure to earth ground as shown in
Figure

3

below
. Use 16
-
gauge, solid
copper wire from an earth grounded cold water pipe clamp to the enclosure.

Figure

3
: Grounding the panel

Grounding wire
W
ater pipe
Grounding clamp

Note:
For best results, we recommend that you crimp a spade lug on the wire
end at the panel and secure the lug to the enclosure.
Chapter 2
:
Installation

12

Concord 4 Installation Manual

Antenna shrouds

Install a plastic antenna shroud (included with panel) over e
ach antenna and
snap them into the holes on the top of the enclosure (skip this step for hybrid and
commercial systems).

Chapter 2
:
Installation

Concord 4 Installation Manual

13

Optional SnapCards

Use the SnapCard header on the right side of the panel (
Figure

4

below
) to install
an optional SnapCard. Install the SnapCard onto the panel SnapCard header
and secure it in place with two screws, included with the SnapCard. To connect
all necessary input/output wiring, refer to the SnapCard documentatio
n.

Figure

4
: Installing a SnapCard

Mounting hole
Snapcard connector
Snapcard
Mounting hole
Chapter 2
:
Installation

14

Concord 4 Installation Manual

Panel terminals

Figure

5

below

shows an overview of panel terminals. The following sections
provide details on how to connect d
evices to the panel.

Figure

5
: Panel terminals

TIP
(+)
RING
(-)
BRN
G
R
Y
GRN
RED
(-)
(+)
(-)
(+)
_
+
NC
COM
SW SW GND #1 #2
+12V - Red
BUS
A
- Green
BUS B - White or
Y
ellow
GND - Black
1
2
3
4
5
6
7
8
9
10
1
1
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
16.5
V
AC
GND
+12V
A
B
SPKR
SPKR
OUT1
OUT2
+12V
MIC
GND
ZONE1
ZONE2
GND
ZONE3
ZONE4
GND
ZONE5
ZONE6
GND
ZONE7
ZONE8
GRN
BRN
G
R
Y
RED

Zones

The panel comes with factory programmed onboard hardwired zones. Install 2
kohm, end
-
of
-
line (EOL) resistors on all unused factory programmed onboard
hardwired zones. If you do
n’t want to install EOL resistors, delete any unused
zones from memory.

Zone inputs 1 through 8 are supervised using the included 2
-
kohm, end
-
of
-
line
resistors at the last device on each circuit. All eight zones accept either normally
open (NO) or normally

closed (NC) detection devices.

Chapter 2
:
Installation

Concord 4 Installation Manual

15

Intrusion detection devices

Figure

6

below

shows the typical wiring for NC and NO door/window intrusion
detection and the typical wiring for a PIR motion dete
ctor. The minimum available
panel voltage for hardwired PIR motion detectors is 8.5 VDC.

Figure

6
: Connecting intrusion detection and motion detector circuits

Panel terminals
Normally closed
(NC) contacts
in series
2 kohm resistor
Normally open
(NO) contacts
in series
2 kohm resistor
Motion
detector
GND
ZONE1
ZONE2
GND
ZONE3
+12V
GND
ZONE5
NC
COM

Smoke detectors

You can connect two
-
wire and four
-
wire smoke detectors

to the system.

Two
-
wire smoke detectors

Zone input 8 can be set up (in program mode) to accept the following 12 VDC,
two
-
wire smoke detectors:

ESL models 429AT, 429C, 429CT, 521B, 521BXT, 521NCSXT (models
521B and 521BXT require the following dip switch s
ettings: 1
-
on, 2
-
off)

Caution:
Use only the two
-
wire smoke detector models listed. Alarm signals from
other detectors may not process correctly if the panel loses AC power and is
operating only from the backup battery.

When set up for two
-
wire smoke detect
ors, zone 8 can handle up to 20 smoke
detectors (all of the same model, as listed above) with 120

uA maximum idle
current per detector. Maximum total loop current allowed in an alarm condition is
90 mA. Connect one or more, two
-
wire smoke detectors to the
panel as shown in
Figure

7

on page 16
.
Chapter 2
:
Installation

16

Concord 4 Installation Manual

Note:
When using two
-
wire smoke detectors on zone 8, the two
-
wire smoke
setting (in program mode) must be turned on
before
entering the learn sensors
m
enu.

Figure

7
: Connecting two
-

and four
-
wire smoke detectors

GND ZONE 7 ZONE 8
GND ZONE 7 ZONE 8
T
wo-wire smoke
detectors
Four-wire smoke
detectors
Panel terminals

Note:
The two
-
wire smoke setting (in program mode) must be on when using
four
-
wire smoke detectors as shown in
Figure

7

above
. See “
Onboard options
-

inputs settings

on page 78

for complete details.

If two
-
wire smoke detectors with built
-
in sounders are used (521INCSXT), a
polarity reversa
l relay (model 405
-
03) may be used to activate the sounders on
all smoke detectors during a fire alarm (see
Figure

8

on page 17
). An output
must be used to activate the polarity reversal rel
ay. This output must be
configured for fire alarm trigger, and siren tracking response (001
-
11).

Note:
Onboard outputs 1 or 2, SnapCard outputs, or output module outputs may
be used to activate the polarity reversal relay.

Maximum alarm current that the pa
nel can source to all external devices is
limited to 1 amp. Be sure to include the alarm current for all sounder smoke
detectors in the alarm current calculation.

Chapter 2
:
Installation

Concord 4 Installation Manual

17

Figure

8
: Polarity reversal module

OU
T
2
+12V
GND
ZONE 8
2
W
-SMK
Polarity reversal
module (part # 405-03)
521NCSX
T
521NCSX
T

Four
-
wire smoke detectors

Termi
nal 24 provides power to four
-
wire smoke detectors that latch and remain in
the alarm state until power turns off, then restores to the detector. The panel
provides this power interruption from terminal 24 (2W SMK ZONE 8) only when
the two
-
wire smoke optio
n is on.

Note:
The two
-
wire smoke feature must be on for smoke detectors to reset after
canceling a fire alarm.

Table

7

below

describes the minimum available panel power. Use only four
-
wire
smoke detectors that operate at these power limits. Connect up to five smoke
detectors as shown in
Figure

7

on page 16
.

Table

7
: Minimum available panel power

Minimum

voltage

Maximum current available

8.3 VDC

Up to 30 mA total (combined alarm) current

8.1 VDC

Up to 40 mA total (combined alarm) current

7.6 VDC

Up to 60 mA total (combined alarm) current

7.1 VDC

Up to 80 mA total (combined alarm) current

Chapter 2
:
Installation

18

Concord 4 Installation Manual

Speaker
s and sirens

The panel provides one siren driver output for intrusion (steady), fire (temporal
3), and auxiliary (on
-
off
-
on
-
off) alarm sounds. This output trips only for partition 1
alarms. Install all sirens/speakers indoors in a concealed location.

Note:

Do not connect a bell or piezo siren to the speaker output (terminals 7 and
8).

The output can drive a single 8
-
ohm speaker or a multiple speaker circuit of 8
ohms or higher. When connecting two or more speakers, wire them in series.
Wiring speakers in pa
rallel can permanently damage the panel. Compatible
speakers are shown below.

Caution:
To avoid disabling the panel speaker output, do not make speaker
connections with the panel power on.

15
-
watt speaker (13
-
060)

For exterior siren applications, connect t
he speaker to the panel using 18
-
gauge
wire as shown in
Figure

9

below
.

Figure

9
: Connecting exterior speakers

Panel terminals
SPKR SPKR
SPKR SPKR
Splice
T
wo 8-ohm speakers
in series (16 ohms)

Hardwired interior speaker (60
-
528)

Connect interior

speakers to the panel (see
Figure

10

on page 19
) using 18
-
gauge wire.

Caution:
Connect only the large speaker to panel terminals 7 and 8 as shown.
The smaller speaker cannot handle output t
o terminals 7 and 8. To avoid
damaging the speaker, do not connect the smaller speaker to terminals 7 and 8.

Chapter 2
:
Installation

Concord 4 Installation Manual

19

Figure

10
: Connecting hardwired interior speakers

SPKR SPKR
SPKR SPKR
Not used
Not used
7
8
7
8

Exterior/interior piezo sirens

Onboard output 1 (OUT 1

terminal 9) is
a 9 to 14 VDC switched, programmable
output that can handle a maximum of 1,000 mA current. The default setting
(01614) activates the output 30 seconds after a police or fire alarm condition
occurs. This allows you to connect a piezo siren without changing
the output
configuration number in programming. This output is typically used for exterior
siren applications. Connect multiple piezo sirens in parallel. (For more
information on output configuration numbers, see “
Onboard options menu

on
page 78
.)

Note:
For 24
-
hour backup, external power drain is limited to 90 mA (during
normal standby condition), using a 4.5 or 5.0 Ah battery, or 190 mA continuous
using a 7.0 Ah battery.

Piezo dynamic exter
ior siren (13
-
950)

Connect the siren to panel as shown in
Figure

11

on page 20
.
Chapter 2
:
Installation

20

Concord 4 Installation Manual

Figure

11
: Connecting exterior sirens

Panel terminals
Red
Black
OUT1
GND

Output 2

Onboard output 2 (OUT 2

terminal 10)

is an open
-
collector (switched path
-
to
-
ground), programmable output that can handle a maximum of 300 mA current
sink and up to 14 VDC. The default setting (01710) activates the output for status
and alarm tones, allowing for a piezo siren connection witho
ut changing the
output configuration number. This output is typically used for interior siren
applications. (For more information on output configuration numbers, see

Onboard options menu

on page 78
.)

Hardwired interior siren (13
-
949)

This siren has two inputs, steady (#1) and warble (#2). Use the steady (#1)
terminal for Concord 4 panels. The siren also includes a cover tamper switch that
can be connected to a hardwired zone input on the p
anel, SnapCard or
SuperBus 2000 hardwired input module. Connect the siren to the panel/zone
input terminals as shown in
Figure

12

below
.

Figure

12
: Connecting an int
erior siren

OUT2
+12V
T
o zone input
2 kohm resistor

Chapter 2
:
Installation

Concord 4 Installation Manual

21

Interrogator 200 audio verification module

A maximum of two audio veification modules (AVM) are allowed (partition 1 only).
Connect the Interrogator 200 AVM to the panel terminals as shown in
Figure

13

below
. Use shielded cable to prevent crosstalk between the speaker and
microphone.

Figure

13
: Connecting an Interrogator 200

Panel terminals
SPKR
SPKR
+12V MIC GND
Y
ellow
Splice
Audio verification
module

Caution:
If a speaker is already connected to panel terminals 7 and 8, the
Int
errogator 200 speaker must be hooked up in series with that speaker to
provide a 16
-
ohm load. Hooking up speakers in parallel to panel terminals 7 and
8 creates a 4
-
ohm load that can cause permanent damage to the panel.
Chapter 2
:
Installation

22

Concord 4 Installation Manual

SuperBus 2000 touchpads

SuperBus 20
00 touchpads may have wires or screw terminals. All use the same
wiring scheme for power and bus connections. Connect touchpads as shown in
Figure

14

below
.

Figure

14
: Connecting touchpads

Panel terminals
T
ouchpad with wires
T
ouchpad with terminals
GND +12V
A
BUS B
GND +12V
A
BUS B
+12V - Red
A
+12V
B
GND/COM
BUS
A
- Green
BUS B - White or
Y
ellow
GND - Black

SuperBus 2000 modules

You may install SuperBus 2000 modules inside the panel cabinet or away from
the panel in the enclosure provided with the module.

Mounting modules inside the panel enclosure

Use the following guidelines when m
ounting modules inside the panel enclosure
(
Figure

15

on page 23
):



Up to four of the SuperBus 2000 modules listed in
Table

3

on page 3

can be
mounted inside the cabinet.



The 2
-
amp power supply and phone interface/voice module each use two
mounting spaces when mounted inside the panel enclosure.



The panel includes two support standoffs you install to secure module
bookplat
es to the panel.

Even if you don’t plan to mount modules inside the cabinet, install the support
standoffs for future use and to avoid losing them.

The cabinet has built
-
in mounting clips on the top and sides that module
backplates slide onto for mounting.

Chapter 2
:
Installation

Concord 4 Installation Manual

23

Figure

15
: Installing SuperBus 2000 modules


SuperBus 2000 2
-
amp power supply (600
-
1019)

Refer to the power supply documentation for the mounting procedure. Connect
the power supply to the panel terminals and devices to be powere
d as shown in
Figure

16

below
.

Note:
Do not connect power (AC and battery) to the power supply until the panel
is ready for power
-
up. For power supply AC and battery connections, refer to th
e
power supply documentation.

Figure

16
: Wiring the SuperBus 2
-
amp power supply to the panel

Panel terminals
Power supply terminals
T
o power inputs on devices
GND +12V
A
BUS B

SuperBus 2000 transceiver modules

The transceiver expands RF reception range when placed near sensors on the
fringe of panel RF receptio
n. Refer to the transceiver documentation for mounting
information.

Connect the transceiver (up to four) to the panel as shown in
Figure

17

on page
24
.
Chapter 2
:
Installation

24

Concord 4 Installation Manual

Figure

17
: Wi
ring transceivers

+12V
A
B
GND/COM
Panel terminals
T
ransceiver terminals
GND +12V
A
BUS B

SuperBus 2000 voice
-
only module

The module can be mounted inside or outside of the control panel cabinet. Refer
to the documentation included with each module, for complete mounting
instructions. For RJ
-
31X connections, see “
RJ31X phone jack

on page 28
.

The module requires panel power and bus connections, and speaker connection
through panel terminals as shown in
Figure

18

below
.

Figure

18
: Wiring for the voice
-
only module

Panel terminals
Module terminals
Not used
GND +12V
A
BUS B SPKR SPKR
+12V
A
BUS B GND SPK 1 SPK 2
AUD 1
AUD 2

SuperBus 2000 phone interface/voice module

The phone interface/voice module includes two backplates for mounting the
module inside the control panel cabinet. You

may also mount the module outside
Chapter 2
:
Installation

Concord 4 Installation Manual

25

of the cabinet using an optional plastic housing (part no. 60
-
800). Refer to the
documentation that comes with each module, for complete mounting instructions.

The module requires panel power and bus connections, phone li
ne connection
through panel terminals and DB
-

8 cord (from an RJ
-
31X jack), and speaker
connection through panel terminals. Connect the module to the panel power and
bus terminals as shown in
Figure

19

be
low
.

For partition 1, connect the phone line to the module through the panel terminals
and DB
-
8 cord (from an RJ
-
31X jack) as shown in
Figure

19

below
. For partitions
2 to 6 ph
one connections, see the documentation that comes with each module.

Figure

19
: Wiring the phone interface/voice module


Note:
To prevent status voice messages from being broadcast outside, do not
connect exterior speakers to phone

interface/voice module terminals 6 and 7.

Wiring for status voice messages only

Connect an interior speaker to the phone interface/voice module terminals as
shown in
Figure

20

on page 26
. W
hen connected as shown, the speaker only
produces status voice messages. In an alarm, the speaker announces voice
status messages.

Wiring for status and alarm messages

Make all of the connections shown in
Figure

20

on page 26

only if the phone
interface/voice module is being installed in partition 1 and alarm sounds are
desired. In an alarm, the speaker alternates between alarm siren tones and voice
status messages.
Chapter 2
:
Installation

26

Concord 4 Installation Manual

Figure

20
: Wiring for status and alarm (or status only) messages

Module terminals
Hardwired interior
speaker (60-528)
For alarm messages
(for status only messages,
do not connect these
panel terminals)
AUD 1
AUD 2
GND
TI
P
1
TI
P
2
RING 1
RING 2
7
8
Panel terminals
SPKR SPKR
+12V
A
B
GND
GND
SPK 1
SPK 2

SuperBus 2000 energy saver module

Connect the energy saver module to the panel and premises thermostat as
shown in
Figure

21

below
. Refer to the energy saver module documentation for
thermostat wiring details.

Figure

21
: Wiring the thermostat and energy saver module

H
V
AC
H
V
AC
Thermostat
Energy saver module
Panel terminals
GND
+12V
A
BUS B

C
hapter 2
:
Installation

Concord 4 Installation Manual

27

SuperBus 2000 8Z input and 4
-
relay output modules

Connect the modules to the panel as
shown in
Figure

22

below
. Connect all
necessary input and output wiring using the module documentation.

Figure

22
: Wiring input and output modules

Input module
Output module
GND +12V
A
BUS B
GND +12V
A
BUS B

SuperBus 2000 au
tomation module

Connect the SuperBus 2000 automation module to the panel as shown in
Figure

23

below
.

Figure

23
: Connecting an automation device

Zone Com
Zone 1
GND
+12V
A
Bus
B
Automation module circuit board
Automation device
DB-9 serial cable
Panel terminals
Chapter 2
:
Installation

28

Concord 4 Installation Manual

SuperBus 2000 wire
less cellular gateway

Connect the SuperBus 2000 wireless cellular gateway module to the SuperBus
2000 terminals as shown in
Figure

24

below
.

Caution:
Since the SuperBus 2000 wireless cellula
r gateway module draws
more than 1 amp, it must be powered by the SuperBus 2000 2
-
amp power
supply and not the panel.

Figure

24
: Connecting a wireless cellular gateway module

1
2
3
4
5
6
24
V
AC
24
V
AC
+12 V
BUS
A
BUS B
GND
GND
GND
+12 V OU
T
ZONE
SuperBus 2000 2-amp
power supply terminals

Phones

The panel cannot be used on a digital or PBX ph
one line. These systems are
designed for digital type devices only, operating anywhere from 5 VDC and up.
The panel uses an analog modem and does not have a digital converter,
adapter, or interface to operate through such systems.

Note:
Some telephones are

polatity
-
sensitive. Green and red wires may need to
be reversed.

RJ31X phone jack

Use the following guidelines when installing an RJ31X phone jack for system
control by phone and central station monitoring:



Locate the RJ31X jack (CA
-
38A in Canada) no fu
rther than 5 feet from the
panel.



The panel must be connected to a standard analog (loop
-
start) phone line,
that provides 48 VDC (on
-
hook or idle).

Chapter 2
:
Installation

Concord 4 Installation Manual

29



For full line seizure, install an RJ31X phone jack on the premises phone line
so the panel is ahead of a
ll phones and other devices on the line. This allows
the panel to take control of the phone line when an alarm occurs, even if the
phone is in use or off
-
hook.

Note:
Connecting the panel to an analog line off the phone switch places the
panel ahead of the
phone system, preventing panel access from phones on
the premises. However, the panel can still be accessed from offsite phones.



If an analog line is not available, contact a telecommunication specialist and
request an analog line off the phone switch (P
BX mainframe) or a 1FB
(standard business line).

To connect a phone line to the panel using an RJ31X/CA
-
38A jack:

1
.

Run a four
-
conductor cable from the TELCO protector block to the jack
location.

2
.

Connect one end of the

cable to the jack.

3
.

At the TELCO protector block, remove the premises phone lines from the
block and splice them to the black and white (or yellow) wires of the 4
-
conductor cable.

4
.

Connect the green and red wires from t
he 4
-
conductor cable to the TIP (+)
and RING (
-
) posts on the block.

5
.

Check the phones on the premises for a dial tone and the ability to dial out
and make phone calls. If phones do not work correctly, check all wiring and
correct where n
ecessary.

Connecting the phone line to the panel with a DB
-
8 cord

After installing the RJ31X jack, you are ready to connect the phone line to the
panel. A DB
-
8 cord (not included) uses a plug at one end for connecting to the
RJ31X module and flying leads
on the other end for panel terminal connections.

To connect the DB
-
8 cord to the panel terminals and RJ31X jack:

1
.

Connect the green, brown, gray, and red flying leads from the DB
-
8 cord to
panel terminals 25, 26, 27, and 28.

2
.

Insert the DB
-
8 cord’s plug into the RJ31X.

3
.

Check the phones on the premises for a dial tone and the ability to dial out
and make phone calls. If phones do not work correctly, check all wiring and
correct where necessary.
Chapter 2
:
Installation

30

Concord 4 Installation Manual

Figur
e

25
: Wiring an RJ31X jack and DB
-
8 cord

BRN
25
26
27
28
T
elco
House
DB-8 cord
RJ31X jack
Dealer cable
T
elco protector
block
Lines from phones
on premises
RING
(-)
TI
P
(+)
G
RY
GRN
RED
GRN BRN G
RY
RED

Power

After connecting and wiring all devices to the panel, you are ready to apply AC
and backup battery power to the panel.

Caution:
Do not plug in the power transformer or connect the ba
ckup battery at
this time. The panel must be powered up using the sequence of steps described
in “
Power up

on page 31
.

AC power transformer

The panel must be powered by a plug
-
in, step
-
down

transformer that supplies
16.5 VAC, 40 VA (600
-
1023 or 600
-
1023
-
CN).

Note:
Do not short the transformer terminals together. The transformer contains
an internal fuse that permanentaly disables the output if the terminals are
shorted.

For systems that incl
ude X10 lamp modules, the panel must be powered with the
line carrier power transformer that supplies 16.5 VAC, 40 VA (600
-
1024 or 600
-
1024
-
CN). Connect the power transformer to the panel as shown in
Figure

26

on
page 31
.

Chapter 2
:
Installation

Concord 4 Installation Manual

31

Backup battery

Use the 60
-
681 (12 VDC, 4.5 or 5 Ah) or 60
-
680 (12 VDC, 7Ah) backup battery.
The battery is automatically tested every 24 hours. Without AC power, the panel
will shut down if the battery voltage falls below 1
0.2 VDC. Replace the battery
when necessary with the same battery model.

Note:
The backup battery leads must be routed along the side of the enclosure
and secured with a cable tie.

Figure

26
: Connecting panel power transformer and
backup battery

Black (negative)
Red (positive)
Battery
1
2
16.5
V
AC

Power up

To power up the panel:

1
.

Connect the red and black backup battery leads (included with panel) to the
lugs on the panel.

2
.

Connect the other ends of the backup battery leads to the battery termin
als.

3
.

Plug the transformer into an outlet that is not controlled by a switch.

4
.

Alphanumeric touchpads display ************, then
SCANNING BUS DEVICES
,
and finally a date and time display.

Note:
If alphanumeric touchpads
don’t display anything, immediately unplug
the transformer and disconnect the backup battery.

5
.

To permanently mount the transformer, unplug it and remove the existing
screw securing the AC outlet cover

WARNING:
Use extreme caution when s
ecuring the transformer to a metal
outlet cover. You could receive a serious shock if a metal outlet cover drops Chapter 2
:
Installation

32

Concord 4 Installation Manual

down onto the prongs of the plug while you are securing the transformer to
the outlet box.

6
.

Hold the outlet cover in place an
d plug the transformer into the lower
receptacle.

7
.

Use the screw supplied with the transformer to secure the transformer to the
outlet cover.

Concord 4 Installation Manual

33

Chapter

3

Programming

Summary

This chapter provides instructions on h
ow to program the Concord 4 and includes
descriptions of the programming settings.

Content

Error! Bookmark not defined.
Chapter 3
:
Programming

34

Concord 4 Installation Manual

Overview

For onsite system programming, you must have an alphanumeric touchp
ad.

You must use an installer/dealer code (default = 4321) to enter program mode.
You must disarm all partitions before you can place the system into program
mode.

Note:
If the system is powered up after the programming touchpad is connected
or if a bus co
mmand scan is executed, the programming touchpad will be
“learned” into the system and must later be manually deleted.

To enter program mode:

1
.

Make sure you disarm the system in all partitions.

2
.

Press
8, 4321, 0, 0
. Th
e display shows
SYSTEM PROGRAMMING
.

To enter program mode using a programming touchpad:

1
.

Connect the red, black, green, and white wires from the programming
touchpad cable (60
-
791) to the power and bus wires/terminals on an
alphanumeric

touchpad, matching the +12V (red), Bus A (green), Bus B
(white), and GND (black) on each.

2
.

Make sure the system is powered up and disarmed.

3
.

Connect the plug on the cable onto the panel programming touchpad header
(see
Figure

27

on page 35
).

4
.

Press
8, 4321, 0, 2
. The touchpad sounds one short beep. Press
*
and verify
that the display shows
SERVICE TOUCHPAD ACTIVE
.

5
.

Press

8, 4321, 0, 0

and the display shows
SYSTEM PROGRAMMING
.

6
.

After programming is complete, disconnect the touchpad from the panel
header.

Chapter 3
:
Programming

Concord 4 Installation Manual

35

Figure

27
: Programming touchpad

Programming touchpad
Programming touchpad
connector
Programming touchpad cable (60-791)

In program mode, touchpad buttons let you
navigate to all installer programming
menus for configuring the system.
Table

8

below

describes the touchpad button
functions in program mode.

Table

8
: Touchpad progr
amming functions

Button

Programming function

#

Select menu item or data entry.

*

Deselect menu item or cancel data entry (if pressed before #).

A (

)

B (

)

Scroll through available options at the current menu tier. Also, scroll
through sensor text options during sensor text programming.

C

Enter pauses when programming phone numbers.

D

Delete certain programmed settings.

0 to 9

Enter numeric values

wherever needed.

1 and 2

Select off (1) or on (2) wherever needed.

1 to 6

Press and hold to enter alphabetical characters A through F for
account numbers

7 and 9

Press and hold to enter * (7) or # (9) for phone numbers.

Chapter 3
:
Programming

36

Concord 4 Installation Manual

Quick programming mode

Use th
e quick programming mode to program basic system programming with a
SuperBus 2000 fixed display touchpad, SuperBus 2000 FTP 1000 touchpad, or
any SuperBus 2000 alphanumeric touchpad. The following menus are
accessible:



Account number (all partitions)



C
S phone 1



CS phone 2



CS phone 3



Learn sensors

limited to selecting sensor number, sensor group, and
partition assignment. An alphanumeric touchpad is required for programming
sensor text in standard programming mode.

See
Table

8

on page 35

for touchpad programming functions.

To enter quick programming mode:

1
.

Make sure the system is disarmed in all partitions.

2
.

Press 8,
installer/dealer code
, 03. The

display shows
ACCOUNT NUMBER.

3
.

Cycle through the menus as shown in
Table

9

below
.

Table

9
: Quick programming menus

Account number

Partition n (1 to

6)

Account number 00000

CS phone

CS phone 1

CS phone none

CS phone 2

CS phone none

CS phone 3

CS phone none

Learn sensors

Sensor partition n (1 to 6)

Sensor group 0

Trip sensor n (1 to 96)

End programming




Chapter 3
:
Programming

Concord 4 Installation Manual

37

Tier 1 programming menus

There are two

basic tiers of programming menus as shown in
Table

10

below
.

Table

10
: Tier 1 and Tier 2 programming menus

Tier 1

Tier 2

System programming

Security

Phones

Phone op
tions

Timers

Light controls

Touchpad options

Reporting

Siren options

Sensors

Audio verification

Accessory modules

Onboard options

Macro keys

Demo kit


Partition 1 copy


Clear memory


Exit programming



This section guides you through tier 1 programmin
g menu items as they appear
in sequence. The exact order you follow depends on whether you’re installing a
new system or changing programming in an existing system.
Chapter 3
:
Programming

38

Concord 4 Installation Manual


System
programming

Use this setting to access the tier 2 programming menus. (See “
Tier 2
programming menus

on page 40
.)

Demo kit mode

Default = Off

This setting determines whether you use your panel for a standard
installation (off) or as a demo kit (on). When the demo kit opt
ion is on, only
sensors learned into groups 01 and 03, duress code use, and phone test
(8,
system master code
, 2) are reported. Turning on this feature and doing
a memory clear changes the following settings:

Partition 1 master code = 1000

Partition 2 mast
er code = 2000

User code 00 = 1001 (partition 1 code


you may use to jump to partition
2)

User code 01 = 1002 (partition 1 code


you may use to bypass sensors)

User code 02 = 2001 (partition 2 code


you may use for remote or offsite
access)

User code 03

= 2002 (partition 2 code


you may use to perform system
tests)

User code 04 = 1122 (partition 1 code


you may use to jump to partition
2, for remote or offsite access, and system tests)

User code 05 = 2233 (partition 2 code


you may use to jump to part
ition
1, for remote or offsite access, bypassing sensors, and system tests)

Partition 1 house code = 255 (P)

Partition 2 house code = 254 (O)

Zone 1 (hardwired input 1) = Group 10, front door

Zone 2 (hardwired input 2) = Group 13, bedroom window

Zone 3 (ha
rdwired input 3) = Group 17, living room motion sensor

Zone 4 (hardwired input 4) = Group 1, panic

Zone 5 (wireless keyfob, ID F00201) = Group 01, (no text)

Zone 6 (wireless DWS, ID A00206) = Group 13, kitchen window

Com failure = off, Demo kit = on

AVM co
de = 1212

Entry delay = 8 seconds

Exit delay = 8 seconds

Extended delay = 1 minute

Siren timeout = 2 minutes

To turn demo kit mode off or on:

1
. With the display showing
DEMO KIT MODE OFF/ON

(current
setting), press
1

(off) or
2

(on). The

display flashes the entered setting.

2
. Press #. The display shows
DEMO KIT MODE OFF/ON
(new
setting).

Chapter

3
:
Programming

Concord 4 Installation Manual

39

Partition 1 copy

Default = None

After programming all settings pertaining to partition 1, you may make an
exact copy to use for partiti
ons 2 to 6. This helps reduce programming
time when the system is set up for multiple partitions. If there are certain
settings that are unique to partitions 2 to 6, simply advance to the
appropriate menu and make the necessary changes.

To copy partition 1
:

1
. With the display showing
PARTITION 1 COPY,
press
#,
installer
code
,
#
. The display flashes.

2
. Press
#.
The display shows
DONE
.

Clear memory

Clearing memory deletes all existing programming information (except the
de
aler code).

Note:
Clearing the memory erases onboard hardwired zone factory
programming.

To clear panel memory:

1
. With the system in program mode, press
A

or
B

until the display shows
CLEAR MEMORY.

2
. Press
#.
The display

shows
ENTER CODE TO CLEAR
MEMORY.

3
. Enter the four
-
digit installer or dealer code (if programmed) and press #.

After about 5 seconds, the system restarts and the panel scans the bus to
learn all bus devices. If the system doesn’t respond
as shown, repeat the
process.

Exiting
programming

After all installer/dealer programming is completed, exit programming
mode.

To exit programming mode:

1
. Press
*

until the display shows
SYSTEM PROGRAMMING.

2
. Press
A

or
B

until the display shows
EXIT PROGRAMMING
READY.

3
. Press
#.
The touchpad displays the time and date
.

Chapter 3
:
Programming

40

Concord 4 Installation Manual

Tier 2 programming menus

Table 10 below shows the tier 2 system programming menus. Where applicable,
the setting name is followed by
the (shortcut) and [default].

Table

11
: System programming menus

Security

Global

Downloader code (0000) [12345]

Installer code (0001) [4321]

Dealer code (0002) [****]

Access code lock (0003) [On]

Ptn security (0004) [On]

Multi ptn
arm (0005) [None]

Keychain tp ptn (0006)

Partition

Account number (0010 to 0060) [00000]

Quick arm (0011 to 0061) [Off]

Quick exit (0012 to 0062) [Off]

Exit extension (0013 to 0063) [On]

Keyswitch sensor (0014 to 0064) [None]

Keyswitch style (0015 to 0065
) [Transition]

Duress code (0016 to 0066) [****]

Phones

CS phone 1

Phone number (01000) [None]

High lvl rpts (01001) [On]

Low lvl rpts (01002) [On]

Exception rpts (01003) [On]

Open/close rpts (01004) [Off]

Backup (01005) [On]

Reporting format (01006) [CID
]

Cellular backup (01007) [On]

CS phone 2

Phone number (01010) [None]

High lvl rpts (01011) [Off]

Low lvl rpts (01012) [Off]

Exception rpts (01013) [Off]

Open/close rpts (01014) [Off]

Backup (01015) [Off]

Reporting format (01016) [CID]

Cellular backup (010
17) [Off]

CS phone 3

Phone number (01020) [None]

High lvl rpts (01021) [Off]

Low lvl rpts (01022) [Off]

Exception rpts (01023) [Off]

Open/close rpts (01024) [Off]

Backup (01025) [Off]

Reporting format (01026) [CID]

Cellular backup (01027) [Off]

Pager 1

P
hone number (01030) [None]

High lvl rpts (01031) [On]

Low lvl rpts (01032) [Off]

Exception rpts (01033) [Off]

Open/close rpts (01034) [Off]

Latchkey rpts (01035) [On]

Streamlining (01036) [On]

Ptn assignment (01037) [1]

Pager 2

Phone number (01040) [None
]

High lvl rpts (01041) [On]

Low lvl rpts (01042) [On]

Exception rpts (01043) [Off]

Open/close rpts (01044) [Off]

Latchkey rpts (01045) [On]

Streamlining (01046) [On]

Ptn assignment (01047) [1]

Pager 3

Phone number (01050) [None]

High lvl rpts (01051) [On]

Low lvl rpts (01052) [On]

Exception rpts (01053) [Off]

Open/close rpts (01054) [Off]

Latchkey rpts (01055) [On]

Streamlining (01056) [On]

Ptn assignment (01057) [1]

Chapter 3
:
Programming

Concord 4 Installation Manual

41

Pager 4

Phone number (01060) [None]

High lvl rpts (01061) [On]

Low lvl rpts (01062) [On]

Exception rpts (01063) [Off]

Open/close rpts (01064) [Off]

Latchkey rpts (01065) [On]

Streamlining (01066) [On]

Ptn assignment (01067) [1]

Pager 5

Phone number (01070) [None]

High lvl rpts (01071) [On]

Low lvl rpts (01072) [On]

Exception rpts (01073) [Off
]

Open/close rpts (01074) [Off]

Latchkey rpts (01075) [On]

Streamlining (01076) [On]

Ptn assignment (01077) [1]

Downloader phone

Phone number (01090) [None]


Phone options

Global

Phone test (02000) [On]

Auto phone test (02001) [Off]

Auto test reset (020
02) [On]

Comm failure (02003) [On]

DTMF dialing (02004) [On]

Dial abort delay (02006) [30 sec.]

Cancel message (02007) [On]

Pager delay (02008) [15 sec.]

Call wait cancel (02009) [Off]

Dial tone detect (02010) [On]

Partition

Local phone ctrl (0210 to 0260)

[On]

Remote access (0211 to 0261) [On]

Ring/hang/ring (0212 to 0262) [On]

Line fail delay (0213 ptn 1 only) [None]

Toll saver (0214 to 0264) [On]

Phone panic (0215 to 0265) [Off]

Phone ACC key (0216 to 0266) [#]

Timers

Global

Supervisory time (0300) [Ran
dom]

RF Tx timeout (0302) [12 hrs]

Phone test freq. (0303) [7 days]

Next phone test (0304) [7 days]

Output trip time (0305) [4 seconds]

Activity timeout (0306) [24 hours]

Daylight savings (0307) [On]

Partition

Entry delay (0310 to 0360) [30 seconds]

Exit D
elay (0311 to 0361) [60 seconds]

Extended delay (0312 to 0362) [4 minutes]

Siren timeout (0313 to 0363) [4 minutes]

Sleep time (0314 to 0364) [22:00]

No usage time (0315 to 0365) [None]

Light control

Partition

Entry lights (0400 to 0450) [None]

House code

(0401 to 0451) [1B 2C 3D 4E 5F 6G

Touchpad
options

Global

Latchkey zones (0500) [None]

Partition

Fire panic (0510 to 0560) [On]

Auxiliary panic (0511 to 0561) [On]

Police panic (o512 to 0562) [On]

Keychain TP arm (0513 to 0563) [Off]

Star is no delay (05
14 to 0564) [Off]
Chapter 3
:
Programming

42

Concord 4 Installation Manual

Reporting

Global

24
-
hour tamper (06000) [Off]

Antenna tamper (06001) [Off]

Buffer control (06002) [Off]

Back in service (06003) [On]

Bypass reports (06004) [Off]

Low CPU battery (06005) [On]

Battery restoral (06006) [Off]

Buffer full rep
ort (06007) [Off]

Zone restorals (06008) [Off]

Two trip error (06009) [Off]

TP panic rpt fmt (06010) [Off]

AC failure (06011) [Off]

Receiver failure (06012) [Off]

RF low bat rpt (06013) [Weekly]

RF supv rpt (06014) [Weekly]

Swinger limit (06015) [1]

Ground

fault (06017) [On]

Aux power fail (06016) [On]

Partition

Opening reports (06100 to 06600) [Off]

Closing reports (06101 to 06601) [Off]

No activity (06102 to 06602) [Off]

Duress option (06103 to 06603) [Off]

Force armed (06104 to 06604) [Off]

Latchkey form
at (06105 to 06605) [Off]

Freeze alarm (06106 to 06606) [Off]

Freeze temp (06107 to 06607) [42]

Alarm verify (06108 to 06608) [Off]

System tamper (06109 to 06609) [Off]

Report confirm (06111 to 06611) [Off]

Siren options

Global

Immediate beeps (0700) [Off
]

Disable trbl beeps (0701) [Off]

UL 98 options (0702) [Off]

Global fire (0703) [Off]

Silent panic (0704) [Off]

Partition

Siren verify (0710 partition 1 only) [Off]

Sensors

Learn sensors (080)

Sensor partition 1 2 3 4 5 6

Sensor group [0]

Trip sensor n

Se
nsor text (081)

Text for sensor
n

Sensor n item 0

Delete sensors (082)

Delete sensor n

Delete sensor n done

Edit sensors (083)

Sn P1 Gnn NC/NO/TP/RF/HW

Sensor partition n

Sensor group n

Audio
verification

Partition 1

Audio verify (09000) [Off]

Audio mod
e (09001) [1]

Fire shutdown (09002) [Off]

Silent talkback (09001) [Off]

Access timeout (09004) [90
seconds]

Beep delay (09005) [2 seconds]

Access code (09006) [****]

VOX mic gain (09007) [14]

VOX gain range (09008) [64]

Manual mic gain (09009) [04]

VOX RX
gain (09010) [08]


Chapter 3
:
Programming

Concord 4 Installation Manual

43

Accessory
modules

Bus device

Unit


ID (10000 to 10015) [Off]

Change ID


Device ID nnnnn

Device partition


Partition assign 1 2 3 4 5 6

Keypad options


Status beeps [On]


Key beeps [On]

Energy options


Freeze temp [4
2

F]


Temperature 40 to 90

F


Temperature 40 to 90

F

Outputs


Output in


Partition assign 1 2 3 4 5 6


Configuration * * * * *

Cellular options


Cellular system [B]

SnapCards

Output programming

Output 1


Partition assign (1
01100) [1]


Configuration (101101) [01400]

Output 2


Partition assign (101110) [1]


Configuration (101111) [00410]

Output 3


Partition assign (101120) [1]


Configuration (101121) [00903]

Output 4


Partition assign (101130) [1]


Configuration (101131) [01003]


Output text

Output 1 (10120)


Output 1 item n

Output 2 (10121)


Output 2 item n

Output 3 (10122)


Output 3 item n

Output 4 (10123)


Output 4 item n

Onboard
options

Inputs

Smoke verify (1100) [Off]

Two
-
wire s
moke (1101) [Off]


Output programming

Output 1


Partition assign (11100) [1]


Configuration (11101) [01614]

Output 2


Partition assign (11110) [1]


Configuration (11111) [01710]

Output text

Output 1 (1120)


Output 1 item n

Output 2 (1
121)


Output 2 item n

Chapter 3
:
Programming

44

Concord 4 Installation Manual

The following sections guide you through the tier 2 system programming menu
items as they appear in sequence:




Security menu

on page 45




Phones menu

on page 50




Phone options menu

on page 54




Timers menu

on page 57




Light control menu

on page 59




Touchpad options menu

on page 60




Reporting menu

o
n page 61




Siren options menu

on page 66




Sensors menu

on page 67




Audio verification menu

on page 71




Accessory modules menu

on page 73




Onboard options menu

on page 78




Macro keys

on page 81

Each tier 2 menu represents a group of settings related to the menu name. Some
tier 2 menus break down into settings tha
t affect the whole system (global) or a
specific partition.

To advance to tier 2 menus from the tier 1 menu, scroll until the display shows
SYSTEM PROGRAMMING,

and then press #. The display shows
SECURITY (
the
first tier 2 menu). You can then scroll throu
gh the tier 2 menus and submenus.

Shortcut numbers

To go directly to some settings in tier 2, you can enter the shortcut number for
that setting. Shortcut numbers in this section are provided after the setting name
(where applicable). Shortcut numbers can

be used from any setting location
within tier 2.

Chapter 3
:
Programming

Concord 4 Installation Manual

45

Security menu

Security
-

global settings


Downloader code

Shortcut: 0000

Default: 12345

Use the five
-
digit downloader code in conjunction with downloader
programming. The downloader operator must have the p
anel account
number and downloader code in order to perform any programming.

You cannot delete the downloader code from the panel memory. To
change the downloader code to its default setting, enter 12345. The
downloader code resets to defaults during a mem
ory clear only if the
dealer code is not set
or
if the dealer code is used to initiate the
memory clear.

Installer code

Shortcut: 0001

Default: 4321

The four
-
digit installer code is used for entering program mode and
changing system settings. If you prog
ram a dealer code, only those
settings not associated with phone numbers and the downloader code
may be changed

You may not delete the installer code or clear it from the panel
memory. To change the installer code to its default setting, enter
4321.

Deale
r code

Shortcut: 0002

Default: None

The four
-
digit dealer code is used to prevent unauthorized persons
from changing the programmed central station phone numbers and
downloader code. When this feature is enabled, central station phone
numbers and the downl
oader code cannot be changed (unless you
enter the program mode by using the dealer code). All other system
settings are still accessible by entering the program mode with the
installer code.

The dealer code cannot be deleted by clearing panel memory. To
d
elete a dealer code, with the display showing
DEALER CODE
nnnn
(current code), press D. The display shows
DEALER CODE
****.

Access code lock

Shortcut: 0003

Default: On

This feature determines whether the panel includes access codes
when sending user infor
mation to the automation module. When this
option is on, it means the access codes are not sent.

Partition security

Shortcut: 0004

Default: On

This feature controls whether an access code is necessary for
partition jumping. When on, you must jump partitio
ns with an access
code by pressing 8,
code
, 6, PTN. When off, you may jump partitions
without an access code by pressing 7, 4, PTN n

(n = 1 to 6).

Regardless of the setting, you may always use an access code to
jump partitions.
Chapter 3
:
Programming

46

Concord 4 Installation Manual

Multipartition
arm/disarm

S
hortcut: 0004

Default: Off. Partition to
turn on

This feature controls which partitions (1 to 6) can be armed/disarmed
simultaneously when using a touchpad and access code assigned to
those partitions. When enabled, users can arm/disarm selected
partitions

using an authorized access code. When disabled, multiple
partitions cannot be armed/disarmed simultaneously. For this feature:

• At least two partitions must be selected.

• Touchpads must be assigned to at least one of the selected
partitions of this menu
.

• Access codes must be assigned to all selected partitions of this
menu. If the partition assignment for a specific access code does not
match the partitions selected in this menu, only those partitions
common to both menu settings can be armed/disarmed
simultaneously with that code.

• A partition cannot be armed/disarmed if it is being controlled by
another source at that time.

• All arming modifiers except Silent affect all partitions being armed.
Only the arming partition can be armed silently.

• When
arming multiple partitions, any conditions that prevent arming
are identified on touchpad displays with the affected partition number
flashing. The normal protest/auto force arm sequence follows, or
pressing *

cancels the arming request.

• When disarming m
ultiple partitions, any partitions in alarm have the
affected partition number flashing on touchpad displays. Pressing #

cancels all alarms in the selected partitions. Alarm memory
information is then displayed for all canceled alarms.

To disable mulitipar
tition arm/disarm, with the display showing
MULTI
-
PTN ARM/DISARM n n n n n n n
, select all of
the partitions by entering the appropriate partition number. The
partition numbers disappear from the display. Press #.

Chapter 3
:
Programming

Concord 4 Installation Manual

47

Keyfob PTN

Shortcut: 0006

Default: On

Thi
s feature controls which partitions the selected keyfob can
arm/disarm. When enabled, the selected keyfob can arm/disarm the
partitions selected in this menu. When disabled, the selected keyfob
cannot arm/disarm multiple partitions. For this feature:

• If
no keyfobs are learned into panel memory, the menu displays
NOT AVAILABLE.

When keyfobs are learned into panel memory,
two submenus appear. The first one lets you view keyfob assignments
similar to that of viewing learned sensors. The second submenu lets
y
ou view and change the multipartition arming assignments for that
keyfob.

• At least two partitions must be selected.

• Keyfobs can arm/disarm multiple partitions only for those partitions
set up in the Multipartition arm/disarm menu.

• A partition cannot
be armed/disarmed if it is being controlled by
another source at that time.

• When arming multiple partitions from a keyfob, any conditions that
prevent arming are identified on touchpad displays in the partition
where that condition exists. Touchpad displ
ays in all other partitions
being armed display
PROTEST
. The normal protest/auto force arm
sequence follows, or pressing *

on any touchpad in a partition being
armed cancels the arming request. Pressing the
Lock

button again
during a protest bypasses any o
pen sensors in the affected partitions
and arms those partitions.

• When disarming multiple partitions with a keyfob and alarms are
active in one or more of the assigned partitions, protest beeps sound
for 5 minutes in all partitions being disarmed; partit
ions in alarm where
sirens have timed out sound protest beeps for 5 minutes; and
partitions in alarm with active sirens continue sounding the alarm.

In any case where alarms are active the premises may not be safe to
enter. The user has these options: leav
e and call for help from a safe
location; if entering the premises anyway, go to a hardwired touchpad
and check the system status to determine the alarm. Disarm and
alarm memory is displayed for all assigned partitions; and press the
keyfob Unlock

button a

second time (within the 5
-
minute protest
period) to disarm all assigned partitions and cancel all alarms, then go
to a hardwired touchpad and check alarm memory.

To enable keyfob PTN:

1
. Learn all keyfobs into panel memory. (See “
Sensors menu

on page
67
.)

2
. Enter this menu (display showing
KEYFOB TP PTN
), then press
#. The display shows the lowest touchpad sensor number assignment
such as:
S1 P1 G0 TP RF
w
here S1 is sensor 1, P1 is partition
1, G0 is sensor group 0, TP is touchpad and RF is wireless.

3
. Press #

to accept this keyfob or press A

or B

until the desired
keyfob appears, then press #. The display shows
ARM
PARTITION
.

4
. Enter the desired partitions 1 to 6 (at least two). The display flashes
the entered partitions.
Chapter 3
:
Programming

48

Concord 4 Installation Manual

5
. Press #

and the display stops flashing.

To disable keyfob PTN:

1
. Enter this menu (display showing
KEYCHAIN TP PTN
)
, then
press #. The display shows the lowest touchpad sensor number
assignment such as:
S1 P1 G0 TP RF
where S1 is sensor 1,
P1 is partition 1, G0 is sensor group 0, TP is touchpad and RF is
wireless.

2
. Press #

to accept this keyfob or pre
ss A

or B

until the desired
keyfob appears, then press #. The display shows
ARM
PARTITION
.

3
. Enter the partition numbers that are displayed (except for the
partition you assigned the touchpad when it was learned). Each
disappears from the
display with the touchpad’s original partition
number left flashing.

4
. Press #

and the display stops flashing.


Chapter 3
:
Programming

Concord 4 Installation Manual

49

Security
-

partition 1 to 6 settings


Account number

Shortcut: 0010 to 0060

Default: 00000

The account number is used as panel

(or customer) identification for the
central monitoring station. The panel sends the account number every
time it reports to the central station. Account numbers must be 1 to 10
characters long.

Alpha characters A to F can be assigned to the account numbe
r by
pressing and holding buttons 1 to 6 respectively, until the character
appears.

When using the CID reporting format, the letter A is reported as a 0.

Quick arm

Shortcut: 0011 to 0061

Default: Off

This feature allows system arming without using an acce
ss code. When
quick arm is on, the system arming level can be increased from off to
stay, from off to away, or from stay to away, without entering an access
code. A valid access code is still required to decrease the arming level
or disarm the system.

Qui
ck exit

Shortcut: 0012 to 0062

Default: On

This feature determines whether or not users can open and close a
standard entry/exit door without causing an alarm (while the system is
armed). This feature also allows you to leave the armed premises
without hav
ing to disarm and rearm the system. When this feature is on,
pressing D

on a touchpad (while the system is armed) starts a two
-
minute timer that allows one standard entry/exit door (sensor groups 10
and 19 only) to be activated once (opened, then closed).
When this
feature is off, you must disarm the system before any protected door is
opened.

Exit extension

Shortcut: 0013 to 0063

Default: On

This feature determines whether you can reenter and exit again through
an entry or exit delay door (without disarmi
ng and rearming the system).
This helps prevent exit faults and false alarms by allowing you to reenter
the premises for a forgotten item.

When this feature is on, the panel restarts the exit delay timer if you
reenter the premises through a standard delay

door before the standard
exit delay time expires. When this feature is off, the exit delay timer
does not restart if you reenter the premises, forcing you to disarm the
system to avoid setting off an accidental alarm.

Keyswitch sensor

Shortcut: 0014 to 0
064

Default: None

This feature lets you arm and disarm the system using either a
keyswitch wired to a hardwired zone input or a wireless door/window
sensor (sensor 01 to 96).

Note:
We recommend you program (learn) keyswitch sensors into
group 28.

For examp
le, if sensor 1 is designated as the keyswitch sensor and the
system is disarmed, then tripping sensor 1 could arm the system to
Away. If the system is armed to Stay or Away, then tripping the sensor
could disarm the system (depending on keyswitch style).

The panel reports opening, closing, and force
-
armed reports (if turned
on) to the central monitoring station.
Chapter 3
:
Programming

5
0

Concord 4 Installation Manual

Note:
A bypassed keyswitch sensor cannot arm or disarm the system.
During an audible alarm, keyswitch sensors can disarm the system
(which sends

a cancel report to the central monitoring station), but
cannot arm the system. The system can be armed only after the siren
timeout expires. Keyswitch sensors test the same as any other sensor
and do not arm or disarm the system during a sensor test.

To d
elete a keyswitch sensor, with the display showing
KEYSWITCH
SENSOR nn
(current sensor number), press D to erase the
keyswitch sensor attribute.

Keyswitch style

Shortcut: 0015 to 0065

Default: Transition

This feature determines how the system behaves when

armed/disarmed
by a keyswitch sensor. The choices are as follows:

Transition (press 1): If keyswitch style is set to transition and the
keyswitch sensor is tripped (opened) when the system is disarmed, the
panel will automatically arm to Away. If the sens
or is tripped (opened)
when the system is armed to Away or Stay, the panel will automatically
disarm

State (press 2): If keyswitch style is set to state, when the keyswitch
sensor is tripped (opened) the panel arms to Away. If the sensor is
restored (close
d) the panel disarms.

Opening, closing, and force arming reports (if turned on) are reported to
the central station for both keyswitch styles.

Duress code

Shortcut: 0016 to 0066

Default: ****

The duress code is a unique 4
-
digit access code that allows use
rs to
operate the system and, at the same time, instructs the panel to send a
silent alarm report to the central station.

Do not use a duress code unless it is necessary. Using duress codes
often results in false alarms due to code entry errors.

To use thi
s feature, the Duress option setting under the “
Reporting
menu

on page 61

must be turned on.


Phones menu

Use the Phones menu to set up central station reporting for the system. The
Phones

menu has the following submenus:



Central station phones 1 to 3 (see “
Phones
-

central station pho
ne 1 to 3
settings

on page 51
).



Pager phones 1 to 5 (see “
Phones
-

pager phone 1 to 5 settings

on page 52
).



Downloader phone (see “
Phones
-

downloader phone settings

on page 54
).

Chapter 3
:
Programming

Concord 4 Installation Manual

51

Phones
-

central station pho
ne 1 to 3 settings


Phone number

Shortcut: 01000,
01010, and 01020

Default: None

Use this setting to program the central station receiver phone number.
Phone numbers can be 1 to 24 digits long, including pauses or *and #
characters.

The phone menus are not

accessible if a dealer code is programmed
and the installer code is used to enter installer programming mode. To
access these menus when a dealer code is programmed, you must
enter installer programming mode using the dealer code. Call
-
waiting
services sh
ould be disabled to prevent interrupting panel communication
to the central monitoring station. To program a dialing prefix that
disables call waiting, see the call wait cancel setting under the menu

Phone options
-

global settings

on page 54
.

To delete a central station phone number, with the display showing
PHONE NUMBER
(current number), press D. The display shows
PHONE NUMBER
_.

High level reports

Shortcut: 01001,
01011, and 01021

Def
ault: On (1),

Off (2 and 3)

When this setting is on, the following conditions report to the central
station:

• Fire, police, auxiliary, and duress alarms

• No activity

• Receiver failure (or jam)

• Tamper conditions, including zone tampers and system tamp
er (40
incorrect key presses or touchpad supervisory)

• Entering or exiting sensor test mode

• Phone test

Low level reports

Shortcut: 01002,
01012, and 01022

Default: On (1),

Off (2 and 3)

When this setting is on, the following nonalarm conditions repor
t to the
central station:

• Force armed

• Hardwired zone trouble (open or short)

• Supervisory (wireless devices)

• Low battery (wireless devices)

• Phone test

• Other nonalarm related conditions

Exception reports

Shortcut: 01003,
01013, and 01023

Default
: Off

When this setting is on, the panel reports to the central station if the
system is not armed or disarmed at the specified schedule times.

Open/close reports

Shortcut: 01004,
01014, and 01024

Default: Off

This setting determines whether opening and c
losing reports are sent to
the central station. When turned on, the panel sends a closing report
when the system is armed and an opening report when the system is
disarmed.

To use this feature, the opening reports and closing reports settings
under the “
Reporting menu

on page 61

must be turned on for that
partition.
Chapter 3
:
Programming

52

Concord 4 Installation Manual

Backup

Shortcut: 01005,
01015, and 01025

Default: On (1),

Off (2 and 3)

This setting determines whether the panel uses anothe
r programmed
central station phone number for reporting if attempts with the first
number are unsuccessful.

When backup is off, the panel makes up to eight attempts to deliver a
report with the programmed phone number. When backup is set to on,
the panel m
akes up to 16 attempts to deliver the report, alternating
between the programmed phone number and the backup phone
number. Central station phone 1 is backed up by central station phone
2. Central station phones 2 and 3 are backed up by central station
phon
e 1.

SIA/CID reporting

Shortcut: 01006,
01016, and 01026

Default: CID

This setting determines whether the panel uses the SIA (press 1) or CID
(press 2) reporting format for central station communication.

Cellular backup

Shortcut: 01007,
01017, and 01027

Default: On (1),

Off (2 and 3)

This setting determines whether the panel uses cellular communication
for reporting if attempts using a landline are unsuccessful.



Phones
-

pager phone 1 to 5 settings


Cellular backup

Shortcut: 01030,
01040, 01050, 0106
0,
and 01070

Default: None

This feature programs a phone number that communicates to a pager.
Phone numbers can be 1 to 24 digits long and include pauses, a sky link
number, and 7
-
digit PIN code.

Call
-
waiting services should be disabled to prevent interrup
ting panel
communication to the pagers. To program a dialing prefix that disables
call waiting, see the call wait cancel setting under the “
Phone options
-

global settings

on page 54
.

To de
lete a pager phone number, with the display showing
PHONE
NUMBER
(current number), press D. The display shows
PHONE
NUMBER
_.

High level reports

Shortcut: 01031,
01041, 01051, 01061,
and 01071

Default: On

This setting determines whether the following alar
m conditions report to
a pager:

• Fire, police, auxiliary, and duress alarms

• No activity

• Receiver failure (or jam)

• Tamper conditions, including zone tampers and system tamper (40
incorrect key presses or touchpad supervisory)

• Entering or exiting

sensor test mode

• Phone test

Chapter 3
:
Programming

Concord 4 Installation Manual

53

Low level reports

Shortcut: 01032,
01042, 01052, 01062,
and 01072

Default: Off

This setting determines whether the following nonalarm conditions
report to a pager:

• Force armed

• Hardwired zone trouble (open or short)

• Sup
ervisory (wireless devices)

• Low battery (wireless devices)

• Phone test

• Other nonalarm related conditions

Exception reports

Shortcut: 01033,
01043, 01053, 01063,
and 01073

Default: Off

This setting determines whether the panel reports to a pager if th
e
system is not armed or disarmed at the specified schedule times, if
open/close reports are turned on.

Open/close reports

Shortcut: 01034,
01044, 01054, 01064,
and 01074

Default: Off

This setting determines whether opening and closing reports are sent to

a pager. When turned on, the panel sends a closing report when the
system arms and an opening report when the system is disarms.

To use this feature, the opening reports and closing reports settings
under the “
Reporting menu

on page 61

must be turned on for that
partition.

Latchkey reports

Shortcut: 01035,
01045, 01055, 01065,
and 01075

Default: On

This setting determines whether the panel reports to a pager when the
system arms or disarms
, according to latchkey time scheduling.

Streamlining

Shortcut: 01036,
01046, 01056, 01066,
and 01076

Default: On

This setting determines whether the panel includes (off) or excludes (on)
the account number when reporting to a pager.

Partition assignment

Shortcut: 01037,
01047, 01057, 01067,
and 01077

Default: 1

This setting determines the partition that reports to a pager. All partitions
may be set to report to a single pager.

Chapter 3
:
Programming

54

Concord 4 Installation Manual

Phones
-

downloader phone settings


Phone number

Shortcut: 01090

Default: No
ne

Use this setting to enter the phone number of an offsite computer that
can be used to program the panel through the phone line. Phone
numbers can be 1 to 24 digits long, including pauses or * and #
characters.

Call
-
waiting services should be disabled to

prevent interrupting panel
communication to the downloader. To program a dialing prefix that
disables call waiting, see the call wait cancel setting under the “
Phone
options
-

global settings

below
.

To delete a downloader phone number, with the display showing
PHONE NUMBER
(current number), press D to erase the number.
The display shows
PHONE NUMBER_
.


Phone options menu

A phone interface/voice module must be installed for the system to us
e these
settings (except line fail delay).

Phone options
-

global settings


Phone test

Shortcut: 02000

Default: On

This setting determines if you can test the communication from the
panel to the central station or a pager by entering 8,
code
, 2 (#, 8,
code
, 2 from a touch tone phone).

Automatic phone test

Shortcut: 02001

Default: Off

This setting determines if the panel sends a phone test automatically
to the central station or a pager on a predetermined schedule. (See
Phone test freq. and Next phone test
under “
Timers
-
global settings

on page 57
).

Automatic test reset

Shortcut: 02002

Default: On

This setting determines whether the automatic phone test interval is
reset after any successful

report to the central monitoring station. (See
Phone test freq. and Next phone test under “
Timers
-
global settings

on page 57
). When this feature is on, the panel considers any
successful
report to the central monitoring station to be a successful
phone test. Thus, any panel report resets the next phone test setting
to the phone test frequency value. The panel only conducts an
automatic phone test if no other reports have been made during t
he
phone test frequency time. Phone test frequency must be set to 2 or
higher for automatic test reset to work.

When this feature is off, an automatic phone test is always conducted
according to the schedule of the phone test frequency setting, even if
the

panel makes other reports to the central monitoring station during
Chapter 3
:
Programming

Concord 4 Installation Manual

55

that time.

Communication
failure

Shortcut: 02003

Default: On

This setting determines whether the panel activates trouble beeps to
alert users on the premises that communication to the cen
tral station
failed. Failure notification occurs after the third unsuccessful reporting
attempt to the central station/pager.

Failure notification can occur immediately if inadequate phone line
voltage is detected upon the initial dialing attempt.

DTMF d
ialing

Shortcut: 02004

Default: On

This setting determines whether the panel uses DTMF tones (on) or
pulse (off) for dialing programmed phone numbers.

Dialer abort delay

Shortcut: 02006

Default: 30 seconds

This setting determines how much time the user ha
s to abort a panel
alarm report (15 to 45 seconds).

Cancel message

Shortcut: 02007

Default: On

This setting determines whether the panel displays a cancel message
after the user disarms the system to clear an alarm condition.

Pager delay

Shortcut: 02008

Default: 15 seconds

This setting determines how long a report is delayed to a pager (0 to
30 seconds), after the panel dials the pager number.

The pager delay time should not be set below 5 seconds, unless
necessary.

Call wait cancel

Shortcut: 02009

Defau
lt: None

This feature sets up a dialing prefix to disable the call waiting feature
before the panel makes its first dialing attempt to any programmed
central monitoring station or downloader phone number. The prefix
can be up to eight digits.

Note:
We reco
mmend that you program two pauses in any call wait
cancel dialing prefix to ensure proper operation.

To delete the call wait cancel prefix, with the display showing
CALL
WAIT CANCEL
(or current setting), press D.

Caution:
Do not change this option from its

default until verifying with
the customer that he has call waiting with his phone service provider.
Changing this option from its default without call waiting will prohibit
the panel from calling the central station.

Dial tone detect

Shortcut: 02010

Defa
ult: On

When this setting is on, the panel begins dialing as soon as it detects
a dial tone. When this feature is off, the panel begins dialing a few
seconds after seizing the phone line. There is no dial tone detect on
the last dialing attempt.

Chapter 3
:
Programming

56

Concord 4 Installation Manual

Phone op
tions
-

partition 1 to 6 settings


Local phone control

Shortcut: 0210 to 0260

Default: On

When this feature is on, the panel can be accessed from a phone on the
premises.

Remote access

Shortcut: 0211 to 0261

Default: On

When this setting is on, the panel
can be accessed from an offsite
phone.

Ring/hang/ring

Shortcut: 0212 to 0262

Default: On

This setting determines how the panel picks up (seizes) the phone line.
Select On if an answering machine shares the phone line with the panel.
Select Off if there is

no answering machine sharing the phone line with
the panel. The remote access setting must be turned on for this feature
to work.

When this feature is on, you must use do the following to call the panel,
listen for one or two full rings and then hang up.
Call the premises again
within the next 10 to 40 seconds. The system answers after the first
ring.

When this feature is off, the system answers after 12 full rings.

Line fail delay

Shortcut: 0213

Default: None

(partition 1 only)

This setting determines th
e amount of time the partition 1 phone line
voltage must be absent before the panel indicates a phone failure
trouble condition (10 to 240 seconds). If a delay is
not
programmed
(default), the panel will not monitor the phone line voltage. Line fail delay
is not available for partitions 2 to 6 at this time.

To delete the line fail delay time, with partition 1 selected, press A

or B

until the display shows
LINE FAIL DELAY nn SECS
(current
setting). Press D

to delete the current line fail delay time.

Toll sa
ver

Shortcut: 0214 to 0264

Default: On

This setting determines whether the panel answers a phone call on the
eighth ring (on) or twelfth ring (off) when a trouble or alarm condition
exists.

Phone panic

Shortcut: 0216 to 0266

Default: Off

This setting dete
rmines whether a police panic alarm can be activated
from a touch
-
tone phone. When this feature is on, pressing #,
******

from
a touch tone phone on the premises causes a panic alarm.

Phone access key

Shortcut: 0216 to 0265

Default: #

This setting determi
nes which touch
-
tone phone button is used for
system access and control. If the local phone control feature is enabled,
the user can pick up the phone and press #

(within 5 seconds) to access
the security system. The panel seizes the phone line and waits f
or the
user to enter system commands. Phone access can be changed from #
(1)

to * (2).

Use the default setting (#) to avoid conflicts between the security system
and other phone devices and services. Many phone devices and
services require *

to initiate t
heir operation, so using *

for this security
feature could cause conflicts.

Chapter 3
:
Programming

Concord 4 Installation Manual

57

Timers menu

Timers
-
global settings


Supervisory time

Shortcut: 0300

Default: set randomly
between 01:00 and
4:00.

This setting determines what time of day the panel sends superv
isory,
low battery, or automatic phone test reports to the central station. Enter
the 4
-
digit time value (HH:MM). For example, enter 0330 to set the
supervisory time for 3:30 a.m.

The panel clock must be set with the correct time for accurate
supervisory t
ime reporting. See “

Time and date menu

on page 83
.

RF Tx timeout

Shortcut: 0302

Default: 12 hours

This setting determines how many hours (2 to 24) the panel has to
receive at least one si
gnal from a wireless sensor (learned into a
supervised group). If the panel does not receive a signal from any
supervised wireless sensor within the set time, the panel reports a
supervisory condition to the central station.

Phone test frequency

Shortcut:

0303

Default: 7 days

This setting determines how often (1 to 255 days) the panel conducts
the automatic phone test (see “
Phone options
-

global settings

on page
54
).

Next phone test

Shor
tcut: 0304

Default: 7 days

This setting is used by the automatic phone test feature under “
Phone
options
-

global settings

on page 54

to determine when the next
automatic phone test should
occur (1 to 255 days). This setting should
be the same as, or less than, the phone test frequency setting.

Output trip time

Shortcut: 0305

Default: 4 seconds

This setting determines how long outputs are activated when tripped (1
to 12 seconds), if they ar
e configured for a momentary response.

Activity timeout

Shortcut: 0306

Default: 24 hours

This setting determines when the system sends a no activity report (1 to
42 hours). If no user interaction or device activation occurs in that time,
the panel sends a

report to the central station.

Daylight saving

Shortcut: 0307

Default: On

When this setting is on, the panel clock automatically adjusts for daylight
saving time changes.

Chapter 3
:
Programming

58

Concord 4 Installation Manual

Timers
-

partition 1 to 6 settings


Entry delay

Shortcut: 0310 to 0360

Default: 3
0 seconds

This setting determines how much time you have to disarm the system
(after entering the armed premises through a designated delay door)
without causing an alarm (30 to 240 seconds).

Exit delay

Shortcut: 0311 to 0361

Default: 60 seconds

This sett
ing determines how much time you have (after arming the
system) to leave the premises through a designated delay door without
causing an alarm (45 to 184 seconds).

Extended delay

Shortcut: 0312 to 0362

Default: 4 minutes

This setting determines how much t
ime you have (after arming the
system) to enter or

exit the premises through a designated extended
delay door

(1 to 8 minutes).

Siren timeout

Shortcut: 0313 to 0363

Default: 4 minutes

This setting determines how long sirens sound (1 to 30 minutes) if no
o
ne is present to disarm the system.

Sleep time

Shortcut: 0314 to 0364

Default: 22:00 (10:00
p.m.)

This setting determines the start time and restart of a 10
-
hour window
during which trouble beeps are suppressed (00:00 to 23:50 using 10
minute intervals).
The initial occurrence of an event that causes trouble
beeps within this window does not sound trouble beeps until the sleep
time window expires. If trouble beeps from a previous event are due to
be restarted during the sleep time window, they restart one
hour prior to
sleep time.

To turn off sleep time, with the display showing
SLEEP TIME
hh:mm
(current setting), press D.

No usage time

Shortcut: 0315 to 0365

Default: None

This setting determines how many days (2 to 255) a partition can remain
disarmed bef
ore the panel sends a no usage report to the central
monitoring station and stores the event in the history buffer.

When this feature is set:

• This timer decreases by one at sleep time each day the selected
partition remains disarmed.

• If the timer gets
to 0 at sleep time, the panel sends a no usage

report
to the central monitoring station and stores the event in the history
buffer.

• If the partition is armed before the timer reaches 0, the timer resets to
the programmed setting.

When this feature is not

set (default), the panel does not send or log no
usage reports.

To turn off no usage time, with the display showing
NO USAGE
TIME
(current setting), press D.


Chapter 3
:
Programming

Concord 4 Installation Manual

59

Light control menu

The Light control menu lets you set up light activation for a specific parti
tion.

Note:
For light control to work you must power the panel with a power line carrier
transformer and X10 powerhouse lamp modules must be installed at desired
lamps.

Light control
-

partition 1 to 6 settings


Entry lights

Shortcut: 0400 to 0450

Default:

None

This setting determines which X10 controlled lights turn on during
entry and exit delays.

The X10 lamp modules set to 1 always turn on during the entry and
exit delays. X10 lamp modules set to 2 always flash the arming level
when arming the system. F
or example, lights flash two times when
arming to stay (Level 2), and three times when arming to away
(Level 3).

To set the entry lights:

1
. With the desired partition selected, press #. The display shows
ENTRY LIGHTS nnnnnnn
(current set
ting).

2
. Enter all the desired light numbers (3 to 9) based on the unit dial
setting on each X10 lamp module.

3
. The display flashes the entered settings. Press #

and the display
shows the new settings.

To delete entry ligh
ts, enter any light number that appears on the
display, then press #. The number disappears from the display.

House code

Shortcut: 0401 to 0451

Default: 01 B, 02 C, 03
D, 04 E, 05 F, and 06
G

This setting enables X10 controlled lights to work in a selecte
d
partition without interfering with the X10 controlled lights of the other
partitions. After setting the panel house code for each partition, you
must set the X10 controlled lights for that partition to the same
house code. The letter that appears automat
ically after the house
code number indicates the necessary house dial setting for X10
modules in that partition (1 to 255).

Chapter 3
:
Programming

60

Concord 4 Installation Manual

Touchpad options menu

Touchpad options
-

global settings


Latchkey zones

Shortcut: 0500

Default: None

This setting defines the ran
ge of keyfobs that will function as latchkey
users (1 to 96). The value you enter in this section may be any valid
zone number. When you enter a zone number, all zones
at
or
below
that
zone number function as latchkey users. For example, if you enter 5,
an
y keyfobs learned into zones 1 to 5 will be latchkey users and all
others (6 to 96) will not.

To delete or disable latchkey zones, with the display showing
LATCHKEY ZONES nnn
(current setting), press D.


Touchpad options
-

partition 1 to 6 settings


Fire
panic

Shortcut: 0510 to 0560

Default: On

This setting determines whether touchpad fire panic buttons are enabled
(on) or disabled (off).

Auxiliary panic

Shortcut: 0511 to 0561

Default: On

This setting determines whether touchpad auxiliary panic buttons ar
e
enabled (on) or disabled (off).

Police panic

Shortcut: 0512 to 0562

Default: On

This setting determines whether touchpad police panic buttons are
enabled (on) or disabled (off).

Keyfob (keychain TP)
arm

Shortcut: 0513 to 0563

Default: Off

When this set
ting is on, pressing the Lock button on keyfob arms the
system directly to away with no delay. When this setting is off, each key
press increments the arming level (for example, from off to stay, from
stay to away).

Star is no delay

Shortcut: 0514 to 0564

Default: Off

This setting determines whether the keyfob Star button controls an
output (off) or the no delay feature (on).


Chapter 3
:
Programming

Concord 4 Installation Manual

61

Reporting menu

Reporting
-

global settings


24
-
hour tamper

Shortcut: 06000

Default: Off

When this setting is turned on, the panel
sounds sirens and reports a
tamper alarm (even when the system is disarmed), when nonfire
wireless sensor tamper switches are activated.

When this setting is turned off, the panel sounds sirens and reports a
tamper alarm only when nonfire wireless sensor t
amper switches are
activated and those sensors are active for the current arming level.
For nonfire sensors not active in the current arming level that have
their tamper switch activated, trouble beeps sound and the panel
sends a sensor tamper report to th
e central station if the system
tamper feature is on for that partition.

Tamper conditions for fire sensors (group 26) always cause trouble
beeps to sound and report the tamper condition to the central station,
regardless of this feature setting.

Antenna
tamper

Shortcut: 06001

Default: Off

This setting determines whether the panel monitors for antenna
tamper of onboard and all connected bus transceivers and receivers.
When turned on, the panel sounds trouble beeps in all partitions and
reports an antenna t
amper condition. Touchpads in all partitions show
a receiver tamper trouble condition. When turned off, the panel
ignores antenna tampers.

Buffer control

Shortcut: 06002

Default: Off

When this setting is on, only arming level changes and time changes
(sys
tem time and daylight saving time) are logged in the buffer
(memory) of the panel. When this setting is off, all system events are
logged in the buffer.

Back in service

Shortcut: 06003

Default: On

When this setting is on, the panel reports to the central
station when
AC and backup battery power are restored (after an extended power
outage).

Bypass reports

Shortcut: 06004

Default: Off

When this setting is on, the panel reports to the central station
whenever sensors or zones are bypassed.

Low CPU battery

Shortcut: 06005

Default: On

When this setting is on, the panel reports a low panel battery to the
central station when the system battery test fails. If this setting and the
Aux power fail feature are both on, the panel also monitors for and
reports a low

battery for the SuperBus 2000 2
-
amp power supply.

Battery restoral

Shortcut: 06006

Default: Off

If this setting is on, the panel reports to the central monitoring station
when a wireless sensor or touchpad reports a battery replacement to
the panel.

Buf
fer full report

When this setting is on, the panel sends an event buffer full

report to
the central monitoring station when the event buffer is nearing full. Chapter 3
:
Prog
ramming

62

Concord 4 Installation Manual

Shortcut: 06007

Default: Off

When turned off, no report is sent.

Zone restorals

Shortcut: 06008

D
efault: Off

When this setting is on, the panel reports a restoral to the central
monitoring station for wireless or hardwire zones in alarm before the
alarm is canceled.

Hardwired smoke detectors connected to panel or SnapCard
hardwired zones do not send r
estorals.

Two
-
trip

Shortcut: 06009

Default: Off

This setting works with the Alarm verify setting (see Alarm verify in

Reporting
-

partition 1 to 6 settings

on page 64
. If Alarm verify is
on,
the panel waits for a second sensor trip before sending an alarm.

If two
-
trip is on and a second sensor trip does not occur

within 4
minutes, the panel sends an error report to the central monitoring
station.

Touchpad panic
report format

Shortcut: 060
10

Default: Off

This setting determines how the panel formats touchpad panic alarm
reports to the central station. When this feature is turned on, touchpad
panic alarms report using the following three
-
digit codes:

• Auxiliary

597

• Police

598

• Fire

599

W
hen turned off, touchpad panic alarms report using a three
-
digit
code from 500 to 515, with the last two digits identifying the touchpad
device number.

AC failure

Shortcut: 06011

Default: Off

When this setting is on, the panel reports to the central stati
on at a
random time between 15 and 45 minutes after AC power to the panel
is lost. Making the report random helps prevent systems in an area
affected by a power outage from trying to report at the same time.

If this feature and the auxiliary power failure
feature are both on, the
panel also monitors for and reports an AC failure for the SuperBus
2000 2
-
amp power supply.

Receiver failur
e

Shortcut: 06012

Default: Off

When this setting is on, the panel reports a receiver failure under the
following condition
s:

• No wireless sensor signals have been received for two hours.

• The receiver is being jammed with a constant signal.

Chapter 3
:
Programming

Concord 4 Installation Manual

63

Flow battery report

Shortcut: 06013

Default: Weekly

This setting determines whether the panel sends daily (1) or weekly
(2) low batte
ry reports to the central monitoring station when a
wireless device is reporting a low battery condition to the panel.

RF low battery report

Shortcut: 06013

Default: Weekly

This setting determines whether the panel sends daily (1) or weekly
(2) low batte
ry reports to the central monitoring station when a
wireless device is reporting a low battery condition to the panel.

RF supervisory report

Shortcut: 06014

Default: Weekly

This setting determines whether the panel sends daily (1) or weekly
(2) reports to

the central monitoring station when the panel detects a
supervisory condition in a wireless device.

Swinger limit

Shortcut: 06015

Default: 1

This setting determines the maximum number of times (1 or 2) a
sensor or zone can go into alarm (during a single

arming period)
before the panel automatically bypasses that sensor or zone. This
feature only applies to sensors or zones in groups 00

20, 29, 34, 35,
or 38.

When set to 1, the panel automatically bypasses a sensor or zone
after it causes an alarm. When s
et to 2, the panel waits until a sensor
or zone has caused a second alarm (during the same arming period)
before bypassing it. At any setting, the automatic bypass is logged
into the event buffer.

A bypassed sensor or zone will be cleared (automatically
un
bypassed) if the system receives no further activations from that
sensor or zone over the next 48 to 50 hours.

Changing the arming level also clears all automatically bypassed
sensors and zones and resets the swinger limit count on all sensors
and zones.

Auxiliary power
failure

Shortcut: 06015

Default: On

When this setting is on, the panel sends a report to the central
monitoring station if the 12 VDC power outputs on the panel and/or
SuperBus 2000 2
-
amp power supply fail.

If this feature is on and the AC
failure and low CPU battery features
are both on, the panel sends AC failure and low backup battery
reports for the SuperBus 2000 2
-
amp power supply.

Ground fault

Shortcut: 06017

Default: On

When this setting is on, the panel will annunciate and send a re
port to
the central monitoring station if it detects current flow between the
panel’s circuitry and the chassis. This indicates that a short to earth
ground exists somewhere in the system.

This feature must be on if hardwired smoke sensors are used in this

system.

Chapter 3
:
Programming

64

Concord 4 Installation Manual

Reporting
-

partition 1 to 6 settings


Opening reports

Shortcut: 06100 to
06600

Default: Off

When this setting is on, the panel sends an opening report to the
central station after disarming the system.

To use this feature, the open/close repor
ts settings under the “
Phones
menu

on page 50

must be turned on for the specific CS phone or
pager number.

Closing reports

Shortcut: 06101 to
06601

Default: Off

When this setting is on, th
e panel sends a closing report to the central
station after arming the system.

To use this feature, the open/close reports settings under the “
Phones
menu

on page 50

must be turned on for t
he specific CS phone or
pager number.

No activity option

Shortcut: 06102 to
06601

Default: Off

When this setting is on, the panel sends a no activity report to the
central station when the activity timeout expires.

Duress option

Shortcut: 06103 to
06603

Default: Off

When this setting is on, the system can be controlled using a
programmed duress code (see “
Security
-

partition 1 to 6 setting

on
page 49
) and will send a duress alarm to the m
onitoring station.

Do not use a duress code unless it is necessary. Using duress codes
often results in false alarms due to code entry errors. If a duress code
is

necessary, use it with the audio verification module to reduce false
alarms and accidental di
spatches. The audio verification module is
listen only.

Force armed

Shortcut: 06104 to
06604

Default: Off

When this setting is on, the panel reports to the central monitoring
station when you “force arm” the system.

Forced arming occurs if you press Bypas
s when arming the system
with open sensors/zones protesting. Auto
-
forced arming occurs when
you do not press Bypass when arming the system with open
sensors/zones protesting, and then leave through an entry/exit door
and the arming protest period expires.
This causes the system to
automatically bypass the open (protesting) sensors. Auto
-
forced
arming always reports to the central monitoring station.

Chapter 3
:
Programming

Concord 4 Installation Manual

65

Latchkey format

Shortcut: 06105 to
06605

Default: Off

This setting determines whether the selected partitio
n is set up for
basic (off) or advanced (on) latchkey opening report operation.

• Basic: If the partition is armed by entering 2

(or 3),
code
, disarming
using a designated latchkey user code or keyfob within an assigned
time schedule sends a page. Arming t
he partition by entering 2

(or 3),
code
, 6

(latchkey) sends a page. If the partition is armed by entering 2

(or 3), code, 6

(latchkey), disarming using a designated latchkey user
code or keyfob inside or outside of an assigned time schedule sends a
page.



Advanced: Arming the partition by entering 2 (or 3),
code
, 6
(latchkey) within an assigned time schedule sends a page.

Refer to the Concord 4 User Manual

for complete latchkey setup and
operation.

Freeze alarm

Shortcut: 06106 to
06606

Default: Off

This s
etting determines whether the panel reports a freeze alarm to
the central station or pager, when the selected partition’s energy saver
module detects a temperature that matches a predetermined setting.

Freeze temperature

Shortcut: 06107 to
06607

Default:
42°F

This setting determines the temperature point the EnergySaver
module detects a potential freeze (heating failure) condition. The
adjustable range is from 40 to 90°F.

This is the same menu found under “
Accessory modules
-

bus device
settings

on page 73
.

Alarm verify

Shortcut: 06108 to
06608

Default: Off

This setting determines whether the panel reports to the central
monitoring station after a single sensor or zone trip (off) or waits f
or a
second trip before reporting (on).

This setting affects sensors/zones in groups 10 through 20. If Alarm
verify is on, group 18 responds the same as group 17 (
Table

24

on
page 130
).

Sy
stem tamper

Shortcut: 06109 to
06609

Default: Off

This setting determines how the panel handles possible tamper
situations. When this feature is on, the panel reacts as follows:

• Initiates an alarm when the system prompts for an access code
(arming/disar
ming, etc.) and several wrong access codes are entered
(40 consecutive invalid key presses).

• Reports to the central station if a bus device stops communicating
with the panel.

• Reports to the central monitoring station if a tamper condition occurs
on un
armed RF (wireless) devices.

Report confirm

Shortcut: 06111 to
06611

Default: Off

When this setting is on, system status speakers announce, “Report is
okay” followed by a single beep each time a successful report is made
to the central monitoring station.

When turned off, no status message
or beep sounds.

Chapter 3
:
Programming

66

Concord 4 Installation Manual

Siren options menu

Siren options
-

global settings


Immediate beeps

Shortcut: 0700

Default: Off

This setting determines whether the panel activates trouble beeps as
soon as a wireless device supervisor
y condition is detected (on), or if
the panel waits 10 hours after the supervisory condition is detected to
activate trouble beeps (off). (See “
Timers
-
global settings

on page 57
).

Disable

trouble beeps

Shortcut: 0701

Default: Off

When you turn on this setting, the panel does not initiate beeps to alert
users of nonfire wireless device supervisory trouble and does not
protest on arming if the condition exists.

If Immediate beeps is on, trou
ble beeps sound for supervisory trouble
conditions regardless of this menu setting.

UL 98 options

Shortcut: 0702

Default: Off

This setting determines whether the panel complies with UL 98
requirements (4
-
hour trouble beep restart, 4
-
hour backup battery t
est, 4
-
hour smoke (group 26) zone supervisory).

Global fire

Shortcut: 0703

Default: Off

This setting determines whether sirens in all partitions sound (on) if any
partition activates a fire alarm.


Silent panic

Shortcut: 0704

Default: Off

This setting de
termines whether touchpad police panic alarms are
audible (off) or silent (on).


Siren options
-

partition 1 setting


Siren verify

Shortcut: 0710

Default: Off

This setting determines whether the panel supervises the panel speaker
terminals (7 and 8). When

this feature is on, the panel indicates a
trouble condition if no speaker is connected to panel speaker terminals.


Chapter 3
:
Programming

Concord 4 Installation Manual

67

Sensors menu


Learn sensors

Shortcut: 080

Default: None

The panel comes with factory programmed onboard hardwired zones.
Install 2 kohm, e
nd
-
of
-
line (EOL) resistors on all factory programmed
hardwired zones. If you don’t want to install EOL resistors, delete any
unused zones from memory. Sensors must be placed in a partition or
sensor group. To change the sensor group or partition assignment

after
adding a sensor or zone, use the Edit sensors menu.

To add (learn) sensors into panel memory:

1
. With the display showing
SENSORS
, press #

and the display shows
LEARN SENSORS
.

2
. Press #

and the display shows
SENSOR

PTN 1
.

3
. Press #

to select partition 1 or press 2, 3, 4, 5, or 6, #

to select the
desired partition. The display should show
SENSOR GROUP 0
.

4
. Enter the sensor group and press #.

(See
Table

24

on page 130

for a
description of all sensor group characteristics.) The display shows
TRIP SENSOR nn
, where nn is the displayed (next available)
sensor number.

5
. To change the displayed sensor number,
enter the desired sensor
number and press #. The desired sensor number is displayed.

6
. With the desired sensor number displayed, use the guidelines in
Table

12

on page 70

to

force the sensor or zone you are adding
(learning) into the panel memory to send a signal to the panel.

7
. To add another sensor to the same sensor group and partition, repeat
the process.

8
. To add sensors to another senso
r group or partition, press
*
twice
and repeat the process.

The factory default zone inputs and group number are:

Zone input 1


Group 10 (entry/exit)

Zone input 2


Group 17 (instant interior follower)

Zone input 3 to Zone input 8


Group 13 (instant peri
meter)

If the panel memory is cleared, all onboard zone factory programming
will be erased.
Chapter 3
:
Programming

68

Concord 4 Installation Manual

Sensor text

Shortcut: 081

Default: None

Use the following guidelines to name zone and sensor locations:

• Use the item numbers that appear in
Table

25

on page 134

for
characters and words listed there.

• If a desired word does not appear in the table create it using the
characters (custom text).

• When using words from the table, spaces between them a
ppear
automatically. When using characters from the table to create words,
you must reserve an item number for a ‘space’ after the word.

• Each character or word uses one item number. For example, a word
from the list counts as one item number.

• Only 16 i
tem numbers are allowed for each zone or sensor name, so
plan before programming sensor text. You may need to abbreviate
words to avoid running out of item numbers.

To program sensor text:

1
. Press A

or B

until the display shows
SENSOR TE
XT
.

2
. Press #

and the display shows
TEXT FOR SN 01
.

3
. Press A

or B

until the display shows the desired sensor number (or
enter the desired sensor number and press #).

4
. Press #

and the display shows:
SN 1
ITEM 0 0
-

________.
Where ITEM 0 is the first character/word location and 0 is the
character/word number.

5
. Enter the number of the character or word, or scroll through the
numbers by pressing B

(forward) or A

(backward). If you make a
mi
stake, enter the correct number or continue scrolling through choices.

6
. Press #

to accept the displayed choice and the display shows:

SN 1 ITEM 1 0
-
.

7
. Repeat the process as needed to complete the zone or sensor name.

8
. Press *

after entering the last character or word number. The display
shows the complete text name. For example:
TEXT FOR SN 01
FRONT ENTRY DOOR
.

Delete sensors

Shortcut: 082

Default: None

Note:
Deleting sensors do not delete sensor text

associated with the
deleted sensor number. To delete sensor text, enter the sensor text
setting and enter 000 (nulls) for each item number.

To remove hardwired zone and wireless sensor numbers from panel
memory:

1
. Press A

or B

until the

display shows
DELETE SENSORS
.

2
. Press #

and the display shows
DELETE SENSOR nn
(lowest
zone/sensor number in panel memory).

3
. Press #

to delete the displayed sensor or, enter the desired sensor
number, then press #.

4
. Repeat the process until all desired sensors are deleted.



Chapter 3
:
Programming

Concord 4 Installation Manual

69

Edit sensors

Shortcut: 083

Default: None

This menu lets you view and, if desired, change the group and partition
assignment for each learned zone or sensor. For example, the displa
y
shows:

S01 P1 G13 NC HW BACK DOOR
.

Where S01 is the zone/sensor number, P1 is partition 1, G13 is sensor
group 13, NC is normally closed, HW is hardwired, and BACK DOOR is
the programmed text name.

Other description codes include:



RF (wireless sensor)



TP (touchpad)



NO (normally open)

To edit sensors:

1
. Press A

or B until the display shows
EDIT SENSORS
.

2
. Press #

and the display shows the sensor or zone with the lowest
number.

3
. Press A or B to scr
oll through all learned zones and sensors.

4
. When the desired zone or sensor is displayed, press #
.
The display
shows
SENSOR PTN n
(current partition assignment).

5
. Enter the desired partition number, then press #. The dis
play shows
the new partition assignment.

6
. Press A

or B

and the display shows
SENSOR GROUP nn
(current group assignment).

7
. Enter the desired group number, then press #. The display shows the
new group assignment.

Chapter 3
:
Programming

70

Concord 4 Installation Manual

Table

12

below

describes how to trip different types of sensors to program (learn)
them in the panel.

Table

12
: Tripping sensors


Sensor

How to trip the sensor

Hardwired
zones

Start with the zone in its “normal” state, and then trip the zone into its
alarm state. A normally closed door, for example, should be closed
when you begin the learn sensors process. To trip the zone, open the
door.

Wireless sensors

Follow the inst
ructions included with each sensor.

Wireless door/window
sensors with external
contacts

Place the external contact in the alarm condition, and then activate the
sensor tamper switch.

Handheld wireless
touchpads

Press the Bypass button.

Keyfobs

Press and

hold the Lock and Unlock buttons together until the keyfob
LED flashes.

ELM keyfobs

Press and release the Unlock button twice quickly, then press and hold
until the LED flashes three times.

Press and release the Unlock button once quickly, then press and

hold
until the LED flashes two times.

Press and hold the Unlock button until the LED flashes once.


Chapter 3
:
Programming

Concord 4 Installation Manual

71

Audio verification menu

The Audio verification menu lets you set up the audio verification module (AVM)
operation in partition 1. If you want audio verifi
cation for partitions 2 to 6, you
must install a standalone audio verification module and a four
-
relay output
module (HOM) (60
-
770) output for that partition.

Audio verification
-

partition 1 settings


Audio verify

Shortcut: 09000

Default: Off

This setting

determines whether the system can be accessed by phone
for alarm verification.


Audio mode audio
verification

Shortcut: 09001

Default: 1

This setting determines how the audio verification module operates.
Choose one of the following:

• Instant (1): Allow
s the central station operator instant access for an
audio session by entering the AVM code or by pressing *

(if an AVM
access code is not programmed) upon completion of panel alarm report
(see “
Access timeout

below
). The panel does not report any alarms
during the AVM session except for fire alarms, even if the operator
extends the session by pressing any valid key.

• Callback (2): Allows the central station operator to place a call to the
premises within 5 minutes of the alarm report (panel picks up after one
ring). The operator must press *

or enter the AVM access code within 20
seconds after ring. The panel does not report any alarms during the
AVM session except for fire alarms, even if
the operator extends the
session by pressing any valid key.

• Callback silent (3):

Same as Callback, except premises phones do not
ring.

Fire shutdown

Shortcut: 09002

Default: Off

This setting determines whether system sirens turn off during a fire
alarm
audio session.

Silent talkback

Shortcut: 09003

Default: Off

This setting determines whether the central station operator can speak
to persons on the premises (on) or only listen (off) during a silent or
duress alarm audio session.

Access timeout

Shortcut
: 09004

Default: 90 seconds

If the audio mode is set to Instant, then this setting determines how
much time (30 to 300 seconds, in 2
-
second increments) the central
station operator has to enter the AVM access code after the panel is
accessed for an audio s
ession.

Beep delay

Shortcut: 09005

Default: 2 seconds

This setting determines how long AVM access beeps are delayed (0 to
300 seconds, in 2
-
second intervals) at the beginning of a two
-
way audio
session.
Chapter 3
:
Programming

72

Concord 4 Installation Manual

Access code

Shortcut: 09006

Default: **** or None

T
his setting determines the four
-
digit code required to access the audio
verification module to start an audio session. If no code is programmed,
pressing
*
starts an audio session.

To delete an access code, with the display showing
AUDIO VERIFY
OFF/ON
, pre
ss A

or B

until the display shows
ACCESS CODE
nnnn
(current code). Press D

to delete.

VOX microphone gain

Shortcut: 09007

Default: 14

This setting determines the microphone sensitivity for triggering voice
-
activated switching (VOX). For the Interrogator 2
00, the default setting
(14) is recommended.

Room size, acoustics, and furnishings where the Interrogator 200 is
located will influence the setting. Setting range is from 01 (low) to 64
(high).

VOX gain range

Shortcut: 09008

Default: 64

This setting deter
mines the gain range for voice
-
activated switching
(VOX). Setting range is from 01 (low) to 64 (high). For best results, this
setting should be higher than the VOX microphone gain.

Manual microphone
gain

Not used.

VOX RX gain

Shortcut: 09010

Default: 08

This setting determines the receiver (talkback) gain level for voice
-
activated switching (VOX). Setting range is 01 to 10. If the VOX is
switching the speaker on when the central station operator is not talking,
lower this setting and the VOX microphone ga
in setting. If the VOX is
not switching the speaker on when the central station operator is talking,
raise this setting and lower the VOX microphone gain setting.


Chapter 3
:
Programming

Concord 4 Installation Manual

73

Accessory modules menu

The Accessory modules menu gives you access to the following menus:

Bus devices:
Use these settings to read bus device unit numbers, assign bus
devices to a partition, and configure other features associated with a specific bus
device. (Most bus device settings do not have shortcut numbers).

SnapCards:
Use these settings t
o set the configuration number for each
SnapCard output, assign SnapCard outputs to a partition, and name the
SnapCard outputs.

Accessory modules
-

bus device settings


Unit
-
ID

Shortcut: 10000 to
10015

Default: **** or None

This menu lets you identify all
connected bus devices, view each unit
number, view the device ID number, and configure other settings based
on a specific device. This menu also lets you delete learned bus
devices.

To help identify bus devices, the 8
-
digit device ID number is also located

on a label on each SuperBus 2000 device.

To identify bus device unit and ID:

1
. With the display showing
BUS DEVICES
, press #. The display
shows the bus unit number and the 8
-
digit device ID number. For
example:
UNIT
-

ID 0

02110185
. Whe
re 0 is the unit number
and 02110185 is the device ID number.

2
. Press A

or B

to identify all other bus unit numbers (0 to 15) and
device ID numbers.

To delete learned unit numbers:

1
. With the display showing
BUS DEVICES
,

press #. The display
shows the bus device set to unit number 0.

2
. Press A

or B

until the bus device unit number you want to delete is
displayed.

3
. Press D. The display changes the unit number to None.
Chapt
er 3
:
Programming

74

Concord 4 Installation Manual

Device ID

Default:
None

This menu lets you change the bus device ID number when replacing a
defective bus device.

To change a device ID:

1
. With the display showing the desired bus device, press #, #. The
display shows
DEVICE ID
(current ID).

2
. Enter the ID of the new bus device. The display flashes the entered
selection. Press #

and the display shows the new setting.

3
. Exit programming mode.

4
. Remove AC and battery power from the panel.

5
. R
eplace the defective bus device with a new one.

6
. Apply AC and battery power to the panel.

Partition assign

This menu lets you assign bus devices to work in the desired partition.

Note:
SuperBus 2000 8Z input modules, SuperBus 2000 4
-
rela
y output
modules, and SuperBus 2000 RF receivers are not assigned to
partitions.

To assign bus devices to partitions:

1
. With the display showing the desired bus device, press #.

2
. Press A

or B

until the display shows
DEV
ICE PTN
and then press
#. The display shows
PARTITION ASSIGN n.

3
. Press 1

to 6

to select the desired partition. The display flashes the
entered selection. Press #

and the display shows the new setting.

Chapter 3
:
Programming

Concord 4 Installation Manual

75

Output programming

Use these setting
s to program the output points of any installed
SuperBus 2000 hardwire output module. The installer programs a HOM
output point into the Concord security panel by entering three kinds of
information.

• Partition: The system partition (1 to 6).

•Trigger: Th
e event that activates the output point. Trigger events can
be partition alarms, trouble conditions, open sensors, etc.

• Response: How the output responds to a trigger event.

Only the onboard and SnapCard outputs can be configured for user
control.

To pro
gram each of the HOM output point configurations into the
security panel:

1
. With the display showing the desired bus device, press #.

2
. Press A

or B

until the display shows
OUTPUTS
.

3
. Press #. The displa
y shows
OUTPUT 1
.

4
. Press A

or B

to select an output, then press #. The display shows
PARTITION ASSIGN 1
.

5
. Press 1

to 6

to select the desired partition assignment for this relay.
The display flashes the entered setting. P
ress #

and the display shows
the new setting.

6
. Press A

or B. The display shows
CONFIGURATION tttrr
(current setting). The point configuration number is tttrr, where ttt is the
trigger number and rr is the response number.

7
. Enter the desired five
-
digit configuration number for this relay. The
display flashes the entered setting. Press #

and the display shows the
new setting.

8
. Press #

and repeat the process until all outputs are programmed.

Status beeps

D
efault: On

This setting determines whether the selected touchpad sounds status
beeps. Each touchpad can be set individually. This feature is usually
turned off for a touchpad that is located in or near bedrooms, to avoid
disturbing sleeping persons.

Key b
eep
s

Default: On

This setting determines whether or not selected touchpads beep when
their buttons are pressed. This feature is usually turned off for a
touchpad that is located in or near bedrooms, to avoid disturbing
sleeping persons.
Chapter 3
:
Programming

76

Concord 4 Installation Manual

Freeze temperature
s

Default: 42°F

This setting determines the temperature point (40 to 90°F) that the
energy saver module detects a potential freeze (heating failure)
condition.

This is the same menu found under Reporting


partition 1 to 6 settings.
The setting is used by

both the SuperBus 2000 energy saver module
and dialog RF thermostat. Individual freeze temperature settings for
each device are not allowed.

Temperatures

Default: None

This setting lets you adjust the energy saver module (ESM) room
temperature setting (4
0 to 90°F) to match the premises thermostat.

To ensure accuracy, wait at least 15 minutes before setting the ESM
temperature to allow the ESM to warm or cool to actual room
temperature.

Cellular system

Default: B

This setting determines the cellular tran
smission system, A (press 2) or
B (press 1) used for cellular communication. This information is provided
by the cellular provider based on installation zip code.


Accessory modules
-

SnapCard settings


Output programming

This setting lets you assign a pa
rtition and a five
-
digit configuration
number for each SnapCard relay output. This number determines both
which system event activates the output and the duration or time the
output is activated.

To program the settings:

1
. Assign the par
tition (1 to 6).

2
. Assign the configuration number (combination of a trigger number
and a response number).

• Trigger: The event that activates the output point. Trigger events can
be partition alarms, trouble conditions, open sensors, etc
.

• Response:

How the output responds when trigger event occurs.

To assign configuration numbers to SnapCard relay outputs:

1
. With the display showing
SNAPCARDS
, press #. Then press A

or B

until the display shows
OUTPUT PROGRAMMING.

2
. Press #

again and the display shows
OUTPUT 1.

3
. Press A

or B

to select the desired output (1

to 4), then press
#
.

4
. With the display showing
PARTITION ASSIGN 1
, press 1

to 6

to select the desired partition.
Press #

to confirm the partition.

5
. Press A

or B

until the display shows
CONFIGURATION tttrr
(current setting).

6
. Enter the desired five
-
digit configuration number for this relay. Press
#

to confirm the setting.

7
. Press #

and repeat the process until all outputs are programmed.

Chapter 3
:
Programming

Concord 4 Installation Manual

77

Output text

Shortcut: 10120 to
10123

Default: None

Entering text for an output allows the user to control it directly or by
schedule. Use the following guidelines to name SnapCard o
utputs:

• Use the item numbers that appear in
Table

25

on page 134

for
characters and words listed there.

• If you want an output for user output control, you must use the output
text featur
e to name the output. If no output text is programmed, the
user will not have access to the output.

• When using words from
Table

25

on page 134
, spaces between them
appear automatically. Wh
en using characters from the table to create
words, you must reserve an item number for a
space
after the word.

• Each character or word uses one item number. For example, a word
from the list counts as one item number.

• Only 16 item numbers are allowed f
or each output name, so plan
before programming output text. You may need to abbreviate words to
avoid running out of item numbers.

To program output text:

1
. With the display showing
SNAPCARDS
, press #, then A

or B

until
the display show
s
OUTPUT TEXT
.

2
. Press #

and the display shows
OUTPUT 1
.

3
. Press A

or B

until the desired output number is displayed.

4
. Press #

and the display shows
OUTPUT N ITEM 0 0
-

where
ITEM 0 is the first character
/word location and 0 is the character/word
number.

5
. Enter the number of the desired character or word, or scroll through
the numbers by pressing B

(forward) or A

(backward). If you make a
mistake, enter the correct number or continue scro
lling through choices.

6
. Press #

to accept the displayed choice and the display shows
OUTPUT N ITEM 1 0
-
.

7
. Repeat the process as needed to complete the output name.

8
. Press *

after entering the last char
acter or word number. The display
shows the complete text name. For example:
OUTPUT 1 GARAGE
DOOR
.

Chapter 3
:
Programming

78

Concord 4 Installation Manual

Onboard options menu

The Onboard options menu includes input, output programming, and output text
settings.

Onboard options
-

inputs settings


Smoke verify

Shortcut: 1100

Default: Off

This setting control the number of sensor group 26 (fire) zone trips
needed to report a fire alarm.

When turned off, hardwire and wireless smoke alarms are reported
immediately.

When turned on:

• Hardwire smoke sensors. Onboard

or SnapCard zones learned into
group 26 must be in alarm for at least 3 seconds or tripped twice within
5 minutes before activating system sirens and reporting to a central
station (or pager).

• Wireless smoke sensors. The firest trip of a group 26 RF sen
sor will
cause a local fire alarm. The second trip of any group 26 zone within the
siren timeout will cause that fire alarm to be reported to the central
station.

Note:

RF smoke detectors repeat the alarm transmission every 60
seconds as long as they are d
etecting smoke. This repeated
transmission will serve as the second zone trip, causing the alarm to be
reported.

Note:

For California State Fire Marshall Listed installations, this feature
must be off.

Two
-
wire smoke

Shortcut: 1101

Default: Off

This sett
ing determines how onboard hardwired zone 8 is configured.
When this setting is on, zone 8 will be configured for two
-
wire smoke
detectors. When off, it will be configured for a normal hardwire input.


Chapter 3
:
Programming

Concord 4 Installation Manual

79

Onboard options
-

output programming settings


Output

1, 2

Shortcuts:

11100 (output 1ptn)

11101 (configuration);
11110 (output 2 ptn),
11111 (configuration)


Default:

Ptn 1, 01614 (output 1)
Ptn 1, 01710 (output 2)

This setting assigns the partition and the five
-
digit configuration number
for the two onbo
ard outputs. The configuration number determines:

• Which system event activates the selected output.

• The duration or time the output is activated.

The first three digits represent the trigger number of an event (such as
triggering an alarm, opening a se
nsor, or arming the system). The last
two digits represent how the output responds, For example, momentary
switching, maintained (or latched) switching, or switching for a preset
time.

Note:
If you want to configure an output for user output control you mu
st
use the output text feature to name the output. If no output text is
programmed, user output control will not function for that output.

Use the system event trigger and response numbers listed in
Table

31

on page 143
.

To set up onboard output 1 and 2 partition and configuration
assignments:

1
. With the display showing
ONBOARD OPTIONS,

press #, B. The
display shows
OUTPUT PROGRAMMING
.

2
. Press #

and the dis
play shows
OUTPUT 1
. Press B

to select output
2.

3
. Press #

and the display shows
PARTITION ASSIGN n
(current
setting).

4
. Press 1 to 6 to assign the output to the desired partition, then press #.
The display shows
PARTITION

ASSIGN
(new setting).

5
. Press B

and the display shows
CONFIGURATION tttrr
(current setting).

6
. Enter the configuration number. The display flashes the entered
number. Press #

and the display shows the new setting.

7
. Press #

and repeat the process until all outputs are programmed.

Chapter 3
:
Programming

80

Concord 4 Installation Manual

Onboard options
-

output text settings


Output text

Shortcut: 1120 to 1121

Default: None

Entering text for an output allows you to control it directly or by
schedule. Use the fo
llowing guidelines to name onboard outputs:

• Use the item numbers listed in
Table

25

on page 134

for characters
and words.

• If you want to configure an output for user output control you m
ust use
the output text feature to name the output. If no output text is
programmed, output control will not function for that output.

• If a desired word does not appear in
Table

25

on page 134
, create it
using the characters (custom text).

• When using words from the table, spaces between them appear
automatically. When using characters from the table to create words,
you must reserve an item number for a space after the word.

• Each charac
ter or word uses up one item number. For example, a
word from the list counts as one item number.

• Only 16 item numbers are allowed for each output name, so plan
before programming output text. You may need to abbreviate words to
avoid running out of item

numbers.

To program output text:

1
. With the display showing
ONBOARD OPTIONS
, press #

then press
B

twice and the display shows
OUTPUT TEXT
.

2
. Press #

and the display shows
OUTPUT 1
.

3
. Press #and the disp
lay shows:
OUTPUT 1 ITEM 0 0
-
. Where
ITEM 0 is the first character or word location and 0 is the character or
word number.

4
. Enter the number of the character or word, or scroll through the
numbers by pressing B (forward) or A (backward).

If you make a
mistake, enter the correct number or continue scrolling through choices.

5
. Press #

to accept the displayed choice and the display shows
OUTPUT 1 ITEM 1 0
-
.

6
. Repeat the process as needed to complete the out
put name.

7
. Press *

after entering the last character or word number. The display
shows the complete text name. For example,
OUTPUT 1 GARAGE
DOOR
.


Chapter 3
:
Programming

Concord 4 Installation Manual

81

Macro keys menu

The macro keys menu lets you set up single
-
button system commands with the

ATP2100 and ATP2600 touchpads.

Macro keys
-

partition 1 to 6 settings


Macro keys

Default:

Chime 71 (macro 1),

Stay 2 (macro 2),

Quick Exit D (macro 3),
Away 3 (macro key 4)

This menu lets you program the Chime, Stay, Exit, and Away macro
keys on ATP21
00 and ATP2600 touchpads. Macro keys let you perform
a system command with one button, eliminating manual entry of the
command. For example, the Stay

key can be programmed so that it
automatically arms the system to Level 2 with no delay just by pressing
i
t once.

• Each partition can accept up to four macros.

• All touchpads in a partition use the same set of macros.

• Macro keys can execute a system command up to 14 key presses in
length. Use keys 0

to 9, #, *, and A

to F

to program macros.

• Panic keys, l
ong key presses (press and hold), and macro keys
themselves cannot be used in a macro.

• When programming a macro to enter user programming, you must
enter two delays (F key) after the access code
-

and before any shortcut
number. For example, the macro ke
y sequence for entering the set time
menu would be 9CODEFF020.

• When using an ATP2100 or ATP2600 to jump to another partition,
pressing the macro buttons on the jumped touchpad will execute macro
commands based on the macros programmed in the jumped parti
tion.

Note:
We recommend that you do not program macros that disarm the
system.

To program/change a macro key:

1
. With the display showing
MACRO KEYS,
press #. The display
shows
PARTITION 1
.

2
. Press A

or B

to select the d
esired partition (1 to 6), then press #. The
display shows
MACRO KEY 1
(current setting).

3
. Press A

or B

to select the desired macro key you want to program (1
to 4).

4
. To change this macro, press the associated macro key.

The current
setting disappears and is replaced with a flashing cursor.

5
. Enter the desired system command. The display flashes the entry.

If
you make a mistake, press the macro key twice to clear the entry and
start over.

6
. Press the macro key again to accept the entered command. The
display stops flashing.

Chapter 3
:
Programming

82

Concord 4 Installation Manual

User programming mode

The user programming mode allows you to view system version information and
program system settings. You can enter user programming from an
alph
anumeric or fixed display touchpad by using the system or partition master
code. The default system master code is 1234. To enter user programming
mode, press 9,
code
. The display shows
TIME AND DATE
. The default settings
are shown in brackets in the table

where applicable.

Table

13
: User programming menus

Time and date

Time


Date


User codes

Regular user

User 00

Direct bypassing [Off]

Remote access [Off]

System test [Off]

Latchkey report [Off]

Partition assign [1]

Partition

master

Partition master code [None]

System master

System master code [1234]

Options

Downloading [On]

Touchpad brightness [2]

Volume [4]


Voice chime [On]

Chime on close [Off]

Set up schedules

Schedule 00 to 15


Start time [00:00]

Stop time [00
:00]

Monday [Off]

Tuesday [Off]

Wednesday [Off]

Thursday [Off]

Friday [Off]

Saturday [Off]

Sunday [Off]

Attach schedule to
events

Latchkey opening

Schedule 00 to 15 [Off]

Latchkey closing

Schedule 00 to 15 [Off]

Exception opening

Schedule 00 to 15 [Of
f]

Exception closing

Schedule 00 to 15 [Off]

Lights 1 to 9

Schedule 00 to 15 [Off]

Output 1 to 6

Schedule 00 to 15 [Off]

Arming

Schedule 00 to 15 [Off]

Chapter 3
:
Programming

Concord 4 Installation Manual

83

Away

Schedule 00 to 15 [Off]

Energy saver

Low setpoint 45 to 89


[50]


High setpoint 48 to 9
0


[90]

Exit programming



System version

Factory code



System number



System level



SW version



Time and date menu

The panel uses a global clock and calendar for time and date. This menu lets you
set this clock and calendar. Alphanumeric touchpa
ds display the panel time and
date whenever the system is disarmed.

Note:
Setting the time and date is important for accurate tracking of system
events stored in the event buffer.


Time

Shortcut: 020

Default: 00:00

This setting lets you adjust the panel cl
ock to the correct time. The panel
uses a 24
-
hour clock (HH:MM). For example, to set the time to 4:17
p.m., enter 1617.

Date

Shortcut: 021

Default: 01/01/00

This setting lets you adjust the panel calendar to the correct month, day,
and year. Enter the cor
rect month (01 to 12), day (01 to 31), and year
(00 to 99). For example, enter 090107 for September 1, 2007.

Chapter 3
:
Programming

84

Concord 4 Installation Manual

User codes menu

The user codes menu lets you program/change regular user access codes,
partition master codes, and the system master code. You c
an enter up to 230
separate user codes, allowing up to 230 different users access to the security
system. You can also specify whether a specific user is able to perform specific
actions, like bypassing sensors or testing the system.


User nnn

Shortcut: 0
30nnn0,
where nnn is user
number 000 to 229

Default: None

User codes provide basic arming and disarming functions. The system
allows up to 230 user codes (user numbers 000 to 229). User numbers
that show
****
indicate no code is currently programmed for th
at
user number.

To program regular user codes:

1
. With the display showing
USER CODES
, press #

and the display
shows
REGULAR USER CODES.

2
. Press #

and the display shows
USER nnn
(first available user
number).

3
. Press A

or B

to select the desired user number, then press #. The
display shows
USER nnn
-

nnnn
.

4
. With the user number displayed, enter a four
-
digit user code. The
display flashes the entered code. Press #

and the display shows
USE
R
nnn
-

nnnn
(new code).

To delete regular user codes:

1
. With the display showing
USER CODES
, press #

and the display
shows
REGULAR USER CODES.

2
. Press #

and the display shows
USER nnn
-

nnnn (
first
available user number
).

3
. Press A

or B

to select the user number/user code you want to delete
(if it is not already displayed), then press #. The display shows
USER
nnn
-

nnnn
.

4
. Enter the system or partition master code. The display flashes t
he
entered code. Press #

and the display shows
USER nnn
--

****
(no code).

Chapter 3
:
Programmin
g

Concord 4 Installation Manual

85

Direct bypassing

Shortcut: 030nnn1,
where nnn is user
number 00 to 229

Default: Off

This setting determines whether a specific user code provides access to
the bypass sensors feat
ure. Set this feature to on for all users who need
to be able to bypass sensors.

To turn the direct bypassing setting off or on:

1
. With the display showing
USER CODES
, press #

and the display
shows
REGULAR USER CODES
.

2
.
Press #

and the display shows
USER nnn
(first available user
number).

3
. Press A

or B

to select the desired user number, then press #. The
display shows
USER nnn
-

nnnn
.

4
. Press A

or B

until the display shows
DIRECT BYPASSI
NG
OFF/ON
(current setting).

5
. Press 1

(off) or 2

(on). The display flashes the entered setting. Press
#

and the display shows the new setting.

Remote access

Shortcut: 030nnn2,
where nnn is user
number 000 to 229

Default: Off

This setting

determines whether the user can access the panel from a
remote phone (a phone located off the premises).

To turn the remote access setting off or on:

1
. With the display showing
USER CODES
, press #

and the display
shows
REGULAR USER CODE
S
.

2
. Press #

and the display shows
USER nn
(first available user
number).

3
. Press A

or B

to select the user number, then press #. The display
shows
USER nnn
-

nnnn
.

4
. Press B

until the display shows
REMOTE

ACCESS ON/OFF
(current setting).

5
. Press 1

(off) or 2

(on). The display flashes the entered setting. Press
#

and the display shows the new setting.

System tests

Shortcut: 030nnn3,
where nnn is user
number 000 to 229

Default: Off

This se
tting determines whether a specific user code provides access to
the phone and sensor tests. Set this feature to on for all users who need
to be able to conduct phone and sensor tests.

To turn the system tests setting off or on:

1
. With t
he display showing
USER CODES
, press #

and the display
shows
REGULAR USER CODES
.

2
. Press #

and the display shows
USER nn
(first available user
number).

3
. Press A

or B

to select the user number, then press #. The display
sh
ows
USER nnn
-

nnnn
.

4
. Press A

or B

until the display shows
SYSTEM TESTS OFF/ON
(current setting).

5
. Press 1

(off) or 2

(on). The display flashes the entered setting. Press
#

and the display shows the new setting.
Chapter 3
:
Programming

86

Concord 4 Installation Manual

Latchke
y report

Shortcut: 030nnn4,
where nnn is user
number 000 to 229

Default:

On (for 000 to 005),

Off (for 006 to 229)

This setting determines whether the user code causes a latchkey report
to be sent to a pager when the code is used to change arming levels
.

To assign the latchkey report attribute to user codes:

1
. With the display showing
USER CODES
, press #

and the display
shows
REGULAR USER CODES
.

2
. Press #

and the display shows
USER nn
(first available user
number).

3
. Press A

or B

to select the user number, then press #. The display
shows
USER nnn
-

nnnn
.

4
. Press A

or B

until the display shows
LATCHKEY OFF/ON
(current setting).

5
. Press 1

(off) or 2

(on). The display flas
hes the entered setting. Press
#

and the display shows the new setting.

Partition assign

Shortcut: 030nnn5
where nnn = user
number 000 to 229

Default: Ptn 1

This setting determines which partitions a user code can access. A code
can be assigned to all pa
rtitions if desired, making it usable at any
touchpad in any partition and able to jump to any selected partition.

To assign partitions to a user code:

1
. With the display showing
USER CODES
, press #

and the display
shows
REGULAR USER COD
ES
.

2
. Press #

and the display shows
USER nn
(first available user
number).

3
. Press A

or B

to select the user number, then press #. The display
shows
USER nnn
-

nnnn
.

4
. Press A

or B

until the display shows
PARTITION ASSIGN
(current setting).

5
. Enter the desired partitions (1 to 6). The display flashes the entered
numbers. Press # and the numbers stop flashing.

Partition master

Shortcut: 0310 to 0315

Default: None

The partition master code
provides access to all system operations and
user programming for a single partition. You must be in the partition of
the partition master code you wish to change.

To change the partition master code:

1
. With the display showing
USER CODE
S
, press #

then A

or B

until
the display shows
PARTITION MASTER CODE.

2
. Press #

and the display shows
PARTITION nnnn
(current
code).

3
. Enter a new four
-
digit code. The display flashes the entered code.
Press #

and the disp
lay shows the new code.

Chapter 3
:
Programming

Concord 4 Installation Manual

87

System master

Shortcut: 0320

Default: 1234

The system master code provides access to all system operations and
user programming. In the partition where the indicating power device is
located, only the system master code may be enab
led to disarm that
partition.

To change the system master code:

1
. With the display showing
USER CODES
, press #

then A

or B

until
the display shows
SYSTEM MASTER CODE.

2
. Press #

and the display shows
SYSTEM MASTER nnnn
(c
urrent
code).

3
. Enter a new four
-
digit code. The display flashes the entered code.
Press #

and display shows the new code.


Options menu

The Options menu lets you set up the system for downloading and silent arming.
You can also adjust al
phanumeric touchpad display brightness from this menu.


Downloading

Shortcut: 041

Default: On

When this setting is on, the panel can communicate with Enterprise
Downloader software for programming the system from offsite.

For this feature to work, the pane
l must be connected to a phone line
and be programmed with remote access on, with a Downloader phone
number, and with a Downloader code.

Touchpad brightness

Shortcut: 043

Default: 2

This setting lets the user lighten or darken the background on touchpad
displays. Each touchpad can be set to compensate for lighting
conditions in the touchpad location. Enter a setting from 0 (darkest
background) to 3 (brightest background).

Volume

Shortcut: 044

Default: 4

This setting determines the volume level of status
sounds from speakers
connected to the phone interface/voice module or voice only module
(VOM).

This menu setting appears only if a phone interface/voice module or a
VOM is connected to the panel. Enter a setting from 0

(off) to 7

(loudest).

Voice chime

S
hortcut: 045

Default: On

This setting determines whether speakers connected to the phone
interface/voice module or voice
-
only module announce perimeter
sensor/zone numbers that are tripped when the chime feature is on.
This menu appears only if a phone int
erface/voice module or a VOM is
connected to the panel.

Chime on close

Shortcut: 046

Default: Off

When this setting is on, the panel sounds a single chime when a
perimeter door or window is closed.

Chapter 3
:
Programming

88

Concord 4 Installation Manual

Set up schedules menu

The set up schedules menu lets yo
u set up timeframes for light control, output
control, automatic arming, latchkey times, and exception opening/closing reports.
The system (all partitions) allows you to set up to 16 schedules (00 to 15) that
are shared by all partitions.

Setting up schedu
les consists of setting a start and stop time for each schedule,
then selecting which days of the week the schedule will be active. You can also
set up a rollover schedule, which starts on one day and ends on another day.
This saves programming time and le
aves more schedules available (in case they
are needed later).

For example, to set up a schedule to rollover from Tuesday evening to
Wednesday morning, set a schedule start time for 2200 (10:00 p.m.) and a stop
time for 0500 (5:00 a.m.). Set the schedule t
o turn on Tuesday. Because the stop
time is set for morning, the system automatically carries the schedule over to the
next day.

If you use the same start and stop times described above and set the schedule to
turn on Monday through Friday, then one schedu
le will cover the entire week.

Chapter 3
:
Programming

Concord 4 Installation Manual

89


Set up schedules

Shortcut: 05XXY,

where XX is schedule
00 to 15 and Y is start
(0)/stop (1) Monday to
Sunday (2 to 8)

Default: 00:00

This menu lets you set up start/stop times for each day of the week.
Schedules used by on
e partition cannot be viewed or changed from a
different partition.

If you are programming schedules for your customer, be sure to record
the settings in the
Concord 4 User Manual
.

To set up a time schedule:

1
. Press A

or B

until the disp
lay shows
SET UP SCHEDULES
.

2
. Press #

and the display shows
SCHEDULE 00
. If you want a
different schedule number, press A

or B

until the schedule number
appears.

3
. Press #

and the display shows
START TIME hh:mm
(current
se
tting).

4
. Enter the starting time (00:00 to 23:59). The display flashes the
entered time. Press #

and the display shows
START TIME hh:mm
(new setting).

5
. Press B

and the display shows
STOP TIME hh:mm
(current
setting).

6
. Enter the desired stop time (00:00 to 23:59). The display flashes the
entered time. Press #

and the display shows
STOP TIME hh:mm
(new setting).

7
. Press B

and the display shows
MONDAY OFF/ON
(current
setting). To select a d
ifferent day, continue pressing B

until the desired
day appears.

8
. Press 1

(off) or 2

(on). The display flashes the entered selection.
Press #

and the display shows the new setting for the selected day.

9
. Repeat the proces
s until all desired settings for each day are set.

Chapter 3
:
Programming

90

Concord 4 Installation Manual

Attach schedules to events menu

This section describes how to link the system events to time schedules.


Latchkey reports

Shortcut:

060nn (opening),

061nn (closing), where
nn is schedule number

Defaul
t: Off

This setting lets you attach the latchkey opening report feature and the
latchkey closing report feature to time schedules.

To attach a schedule to latchkey opening or latchkey closing:

1
. Press A

or B

until the display shows
ATTAC
H SCHEDULES TO
EVENTS
.

2
. Press #

then A

or B

until the display shows
LATCHKEY OPENING
or LATCHKEY CLOSING
.

3
. Press #

and the display shows
SCHEDULE 00 OFF/ON
(current
setting). If you want a different schedule, press A

or
B

until the desired
schedule appears.

4
. Press 1

(off) or 2

(on). The display flashes the entered selection.
Press #

and the display shows the new setting for the selected
schedule.

Exception reports

Shortcut:

062nn (opening),

063nn (cl
osing), where
nn is schedule number

Default: Off

This setting lets you attach the exception opening report feature and the
exception closing report feature to time schedules.

To attach a schedule to exception opening or exception closing:

1
. Press A

or B

until the display shows
ATTACH SCHEDULES TO
EVENTS
.

2
. Press #

then A

or B

until the display shows
EXCEPTION
OPENING OR EXCEPTION CLOSING
.

3
. Press #

and the display shows
SCHEDULE 00 OFF/ON
(current
setting
). If you want a different schedule, press A

or B

until the schedule
appears.

4
. Press 1

(off) or 2

(on). The display flashes the entered selection.
Press #

and the display shows the new setting for the selected
schedule.

Chapter 3
:
Programming

Concord 4 Installation Manual

91

Lights

Shortcut:

064xnn
where nn is schedule
number and x is light
number minus 1

Default: Off

This setting lets you attach light controls to a time schedule.

To attach schedules to lights:

1
. Press A

or B

until the display shows
ATTACH SCHEDULES TO
EVEN
TS
.

2
. Press #

then A

or B

until the display shows
LIGHTS
. Press #

to
enter the Lights menu.

3
. Press A

or B

until the light appears.

4
. Press #

and the display shows
SCHEDULE 00 OFF/ON
(current
setting). If
you want a different schedule, press A

or B

until the desired
schedule appears.

5
. Press 1

(off) or 2

(on). The display flashes the entered selection.
Press #

and the display shows the new setting for the selected
schedule.

6
. Repeat the process until all desired lights are attached to schedules.

Outputs

Shortcut: 065xnn
where nn is schedule
number and x is output
number minus 1

Default: Off

This setting lets you attach outputs to a time schedule. Onboard outputs
are 1 to 2
; SnapCard outputs are 3 to 6.

Only onboard and SnapCard outputs can be scheduled. These outputs
can only be scheduled if output text has been entered in installer
programming and if the output is assigned to the same partition as the
touchpad used.

To att
ach schedules to outputs:

1
. Press A

or B

until the display shows
ATTACH SCHEDULES TO
EVENTS
.

2
. Press #

then A

or B

until the display shows
OUTPUTS
. Press #

to
enter the Outputs menu.

3
. Press A

or B

until

the output appears.

4
. Press #

and the display shows
SCHEDULE 00 OFF/ON
(current
setting). If you want a different schedule, press A

or B

until the schedule
appears.

5
. Press 1

(off) or 2

(on). The display flashes the enter
ed selection.
Press #

and the display shows the new setting for the selected
schedule. Repeat the process until all desired outputs are attached to
schedules.
Chapter 3
:
Programming

92

Concord 4 Installation Manual

Arming

Shortcut: 0660nn
where nn is schedule
number

Default: Off

This setting lets you arm accor
ding to a time schedule. This setting will
allow you to arm to away

only. There is no disarm schedule.

To attach schedules to arming:

1
. Press A

or B

until the display shows
ATTACH SCHEDULES TO
EVENTS
.

2
. Press #

then A

or

B

until the display shows
ARMING
.

3
. To select arm to Away press #.

4
. Press #

and the display shows
SCHEDULE 00 OFF/ON
(current
setting). If you want a different schedule, press A

or B

until the schedule
appears.

5
. Press 1

(off) or 2

(on). The display flashes the entered selection.
Press #

and the display shows the new setting for the selected
schedule.

6
. Repeat the process until all desired schedules are attached.


Energy saver menu

The E
nergy saver menu lets you set the energy saver module or dialog RF
thermostat low
-

and high
-
setpoints. These setpoints override the premises
thermostat allowing the energy saver module or dialog RF thermostat to activate
the furnace/air conditioner.


Low s
etpoint

Shortcut: 070

Default: 50°F

This setting determines the temperature at which the energy saver
module relay closes to activate the furnace. The low setpoint cannot be
set equal to or higher than the high setpoint. Enter the desired
temperature (45 t
o 89°F).

High setpoint

Shortcut: 071

Default: 90°F

This setting determines the temperature at which the energy saver
module relay closes to activate the air
-
conditioner. The high setpoint
cannot be set equal to or lower than the low setpoint. Enter the
desired
temperature (46 to 90°F).


Attach lights to sensors menu

This menu lets you assign a light number to a sensor. Each time the sensor is
activated, the attached light will turn on for 5 minutes. When the 5
-
minute timer
expires, the light will turn
off. If the same light is scheduled, it will only turn on
during the schedule time.

Chapter 3
:
Programming

Concord 4 Installation Manual

93


Light X to Sensor Y

Shortcut: 08n where n
is light number minus 1

Default: 0

This menu attaches light x to sensor y. Each time a selected sensor is
tripped, the selected
light will turn on and a 5
-
minute timer will start. The
sensor must be learned into the current partition before it can be
attached.

To attach a light to a sensor:

1
. With the display showing
LIGHT 1 TO SENSOR y
(current
setting), press A

or B

to select the light number.

2
. Enter the sensor number (01 to 96). The display flashes the entered
setting. Press #

and the display shows the new setting.

3
. Repeat the process until all desired lights are attached to
sensors.

To detach a light from a sensor:

1
. With the display showing
LIGHT 1 TO SENSOR y
(current
setting), press A

or B

to select the light number.

2
. Enter 0

as the sensor number and press #.


System version menu

The S
ystem version menu lets you view and identify panel hardware and
software. This information is primarily used for troubleshooting purposes.


System version

Shortcut:

010 (factory code),

011 (system number),
012 (system level),

013 (software version)

Th
is menu lets you view and identify panel hardware and software
version.

To view and identify the system version:

1
. Press A

or B

until the display shows
SYSTEM VERSION
.

2
. Press #

and the display shows
FACTORY CODE nnn*nnn
n
.

3
. Press B

and the display shows
SYSTEM NUMBER *nnnnnnn
.

4
. Press B

again and the display shows
SYSTEM LEVEL nnnn
.

5
. Press B

again and the display shows
SW VERSION nnnnx
(panel firmware version).


Downlo
ader programming

The panel can be programmed remotely using Enterprise Downloader. Use the
information you recorded in
Appendix

A


System planning sheets

on page 117

to inform the downloading operator of the programming requirements for this
system.
Chapter 3
: Programming

94
Concord 4 Installation Manual

A Downloader phone number should be programmed and the user
-
programmable option Downloading must be powered on for remote downloader
programming to work.

To
initiate an Enterprise Download session:

1. Contact your download station and ask the operator to prepare to download
to the panel.

2. Make sure the system is disarmed.

3. Press 8,
system master code
, 7, 0

(any), 1

(down) or 2

(up). The display
shows
SYSTEM DOWNLOAD IN PROGRESS
during the downloading process.

If the alphanumeric touchpad does not display
SYSTEM DOWNLOAD IN
PROGRESS,
call the downloader operator to verify the downloader phone
number. Also, ma
ke sure Enterprise ToolBox is set up properly.

These programming options can only edited with Enterprise Toolbox:

SIA
F
alse
A
larm Enabled
Auto
S
tay
A
rming Enabled




Concord 4 Installation Manual

95

Chapter

4

Testing and
troubleshooting

Summary

This chapter provides information to help you test and troubleshoot the system.

Content

Error! Bookmark not defined.
Chapter 4
:
Testing and troubleshooting

96

Concord 4 Installation Manual

Testing the system

Before testing, we recommend that you close the panel cabinet door and the
covers on all modules (mounted outside the cabinet.) The testing environment
should match the system working environment
.

You should test the system after installation or service and after adding or
removing devices from the system. See “
Cellular backup commu
nication

on
page 104

if you do not achieve correct

test results.

Testing the system includes:




Basic system commands

below




Zones/sensors

on page 97




Phone communication

on page 98




Central station/pager communication

on page 99




Outputs and sirens

on page 100




Light control

on page 101




Energy saver module (ESM)

on page 101




Fixed display LCD touchpad chime and trouble beep tones

on page 102




Au
dio verification module communication

on page 103




Cellular backup commu
nication

on page 104

Basic system commands

Table

14

below

describes basic touchpad operating commands. For c
omplete
details on system operation, including user programming, refer to the Concord 4
User Manual.

Table

14
: Basic touchpad commands

Command

System response

* (STATUS)

Indicates current system status

*, *

Indicates AC power, b
attery, and current system status

1,

code

Disarms system to OFF

2,
code

Arms system to STAY

2 (quick arm on)

Arms system to STAY

3 (quick arm on)

Arms system to AWAY

2 or 3,

code
, 4

or

2 or 3, 4

Arm system

no delay (no exit or entry delay)

5, 2 or 3,

code

or

5, 2 or 3

Arms system silently (no arming status beeps

Chapter 4
:
Testin
g and troubleshooting

Concord 4 Installation Manual

97

Command

System response

* (STATUS)

Indicates current system status

7, 1

Turns chime feature on and off

7, 2

Turns energy saver on and off

7, 4

Partition jump without entering code (only if partition
security opti
on is off)

7, 6

Identifies alarms in memory

7, 7, n (n = output number [1to6])

1 to 2 = onboard outputs;

3 to 6 = module outputs

Turns the output on or off. (This command is only
functional after output text is entered into panel
memory.)

8,

code
, 2

I
nitiates a phone test

8,
cod
e, 3

Initiates a sensor test

8,

installer code
, 3

Initiates a dealer sensor test

8,
code
, 6

Partition jump

8,
code
, 8

View event history

0, 0

Turns all controlled lights on and off

0, n (n = light number 1 to 9)

Turns indi
vidual controlled light on and off


Zones/sensors

Test sensors/zones after all programming is completed; whenever there is a
change in environment, equipment, or programming; and whenever a zone
-

or
sensor
-
related problem occurs.

If the system does not re
spond as described in the following procedure, see
Troubleshooting.

Note:
While the sensor test is a valuable installation and service tool, it only tests
sensor operation for the current conditions. You should perform a sensor test
after any change in env
ironment, equipment, or programming.

To test zones/sensors:

1
.

Place all sensors and zones in their nonalarm state.

2
.

At an alphanumeric touchpad, enter the sensor test mode by pressing 8,
installer code
, 3. The touchpad
sounds one beep and displays
SENSOR
TEST
. The panel starts a 15
-
minute timer.

3
.

Trip each zone/sensor one at a time. Touchpads (and interior sirens) should
sound one short, high
-
pitched beep, and the display should show the sensor
name (or

number) and OK.
Chapter 4
:
Testing and troubleshooting

98

Concord 4 Installation Manual

4
.

Press the Status

button when you think all zones/sensors are tested. The
touchpad displays any untested sensors/zones and touchpad panics. If all
sensors/zones and touchpad panics have been tested, the display shows
SENS
OR TEST OK
.

5
.

Test any untested zones/sensors and touchpad panics.

Note:
If you hear a long, low
-
pitched beep, proceed to “
If a wireless sensor
does not test

below
.

6
.

The system stays in sensor test mode for 15 minutes. When less than 5
minutes remain, touchpads and interior sirens beep and the panel announces
the remaining time over the speakers once every minute. After 15 minutes,
the panel disarms to off
automatically. If you need more time to complete the
sensor test, press 8,

installer code
, 3

while the system is still in sensor test
mode. This restarts the 15 minutes of test time.

7
.

When all sensors/zones and touchpad panics have been t
ested, press 1,
installer code

to exit sensor test mode.

If a wireless sensor does not test

If touchpads display
SENSOR FAILURE
and sirens sound a long, low
-
pitched
beep when a zone or sensor is tripped, this indicates that the wireless sensor
signal stren
gth is below acceptable limits affecting the sensor signal strength.

When possible, locate wireless sensors within 100 ft. of the panel. While a
transmitter may have a range of 1,000 ft. (3000 m) or more out in the open, the
environment at the installation

site can have a significant effect on transmitter
range. See Troubleshooting to resolve the problem.

For wireless sensors that don’t respond, use an RF Sniffer (60
-
401) test tool to
verify that the sensor is transmitting. Constant beeps from the RF Sniffe
r indicate
a runaway (faulty) sensor. Remove the sensor batteries and replace the sensor.

Phone communication

Do a phone test to check the phone communication between the panel and the
central monitoring station.

To test phone communication:

1
.

Contact the central monitoring station to inform them that you are testing the
system.

2
.

Press 8,
system master code
, 2. The display reads
PHONE TEST
and the
touchpad sounds one beep. When the panel completes the test, the system
re
turns to the previous arming level automatically.

Chapter 4
:
Testing and troubleshooting

Concord 4 Installation Manual

99

3
.

If the display continues to show
PHONE TEST
for 90 seconds or more, enter
1,
system master code

and see Troubleshooting.

Central station/pager communication

After doing sensor and phone
tests, check that the system is reporting alarms
successfully to the central station or pager.

Caution:
Be sure to contact the central monitoring station before activating
outputs that trigger from an alarm condition.

Account numbers vary when displayed, d
epending on pager service. Account
numbers are not displayed if Streamlining is turned on.

To test communication with the central station/pager:

1
.

Call the central station and tell the operator that you will be testing the
system.

2
.

Arm the system.

3
.

Test each of the touchpad and wireless panic buttons and trip at least one
sensor of each type (fire, intrusion, etc.) to verify correct operation.

4
.

Check pager displays to verify reports ar
e received. Pagers display an event
code, digit sensor number, and the last four digits of the account number. A
pager display of
999 002 7468
indicates the following:

999 (alarm condition)

002 (sensor/zone in alarm or user number)

7468 (last four digits o
f account number)

5
.

When you finish testing the system, call the central monitoring station to verify
they received the alarms.

Table

15

below

describes pager system event c
odes

Table

15
: Pager system event codes

Codes

System event

009

Zone restoral

111

System disarmed

115

Sensor test exit

118

Trouble condition cleared

119

Alarm canceled

222

System armed to STAY
Chapter 4
:
Testing and troubleshooting

100

Concord 4 Installation Manual

Codes

System event

333

System armed to AWAY

555

Pho
ne/sensor test

888

System trouble condition

999

System in alarm


Table

16

below

describes pager sensor/zone number and user number report
codes.

Table

16
: Pager se
nsor/zone code and numbers

Code

Sensor/zone or user number

000

System event not caused by a zone or user

001

096

Sensor/zone numbers 1 to 96

600

829

Regular user codes 0 to 229 used

830
-
837

Partition master code used

838
-
845

Partition duress code used

846

System master code used

847

Installer code used

848

Dealer code used

850

Quick arm used

851

Keyswitch sensor used

852

System armed Itself (during service or power
-
up)


Outputs and sirens

You should test all outputs (onboard and SnapCard) to ver
ify configuration
programming.

Note:
Be sure to contact the central monitoring station before activating outputs
that trigger from an alarm condition.

To test outputs:

1
.

Contact the central monitoring station to inform them you are testi
ng the
system.

2
.

Verify that all wiring at the panel and output devices is correct.

3
.

Activate the appropriate device to trigger each output as programmed.

Chapter 4
:
Testing and troubleshooting

Concord 4 Installation Manual

101

4
.

Verify that each output responds according to t
he programmed configuration
number. For outputs that trigger sirens, verify that the correct alarm sounds
are produced from these sirens (see
Table

17

be
low
).

5
.

Contact

the central monitoring station when you are finished testing.

Table

17

below

describes the system alarm sounds you should hear for each
alarm event.

Table

17
: System

alarm sounds

Alarm type

Alarm sound

Fire

Repeating series of three beeps

Police/Intrusion

Continuous tone

Auxiliary

Rapid beeps


Light control

Test all lights plugged into X10 lamp modules to verify house code and light
number settings.

To test light
control:

1
.

Press 0, 0

repeatedly to turn all lights on and off together.

2
.

Press 0, 1

repeatedly to turn light 1 on and off.

3
.

Repeat step 2 for remaining lights (0 + 2 for light 2, 0 + 3 for light 3, et
c.).

4
.

Arm the system to away. All lights plugged into modules set to unit 1 (or set
as entry lights) should turn on and stay on for 5 minutes. All lights plugged
into modules set to unit 2 should blink three times to indicate the arming l
evel.
Remaining lights should not be affected.

5
.

Disarm the system. If unit 1 (or entry) lights were on for an entry or alarm,
they will turn off in 5 minutes. Unit 2 lights should blink once to indicate the
system is off. Remaining lights

should not be affected.

6
.

All lights should turn on and remain on during fire and auxiliary/medical
alarms. All lights should flash during a police or intrusion alarm.

Energy saver module (ESM)

Test the energy saver module to verify it ov
errides the thermostat.

Note:
The system must have high
-

and low
-
temperature limits set to test the
energy saver module.
Chapter 4
:
Testing and troubleshooting

102

Concord 4 Installation Manual

To test the energy saver module:

1
.

Press *, * to display the system status,
ENERGY SAVER OFF
, and the present
TEMPER
ATURE nn
°. The temperature displayed (and/or announced) should
match the house thermostat. If the temperatures do not match, refer to

Accessory modules
-

bus device settings

on page 73
.

No
te:
There is a 5
-
minute delay after the energy saver module returns control
to the furnace/AC before it will override the furnace/AC again.

2
.

Press 7, 2

to turn on the ESM. The display shows
ENERGY SAVER ON
and
the ESM relay will click onc
e.

3
.

Press 7, 2

again to turn the ESM off. The display shows
ENERGY SAVER
OFF.

Fixed display LCD touchpad chime and trouble beep
tones

You can adjust the frequency (pitch) of chime and trouble beep tones from a
fixed display touchpad to a
more desirable or distinct tone, or to compensate for
hearing impaired persons.

To change status tone pitch:

1
.

Press and hold the *

and 0

buttons together until you hear a steady tone, then
release the buttons.

Note:
Chime and trouble be
ep tones sound using the default frequency
during, or within 15 seconds of, any button activity at that specific touchpad.

2
.

Press and hold 1

to lower the pitch or press and hold 2

to raise the pitch.

3
.

Release the button
when the desired pitch is heard.

After about 15 seconds of no touchpad activity, the steady tone stops
sounding.

Touchpad display contrast

You can adjust touchpad displays for easier viewing to help compensate for
lighting conditions in the touchpad locati
on. The contrast adjustment lightens or
darkens the text. (Vacuum fluorescent displays do not have a contrast
adjustment.)

To adjust display contrast:

1
.

Enter configuration mode by pressing the D

and 6

buttons together for at least
2 sec
onds. The display shows
DA nnn
.

Chapter 4
:
Testing and troubleshooting

Concord 4 Installation Manual

103

2
.

Press and release the 1

and 2

buttons together repeatedly, until the desired
contrast level is displayed.

3
.

Press *

and the display briefly shows
DONE
, and then shows the time and
date.

Au
dio verification module communication

Test the audio verification module (AVM) from offsite and the central station to
verify that it works properly.

You will need a helper and DTMF phone at an offsite location to perform this test.
When testing the AVM fr
om offsite you must follow these guidelines:



Set the remote access feature to on (default).



Set the audio verify feature to on.



Set the system to a nonalarm state.



Set the optional ring/hang/ring feature (default) to work with steps 1 and 2
below.
Otherwise wait for 12 rings and the panel will pick up automatically.

To test the module from offsite:

1
.

The offsite helper calls the panel, lets the phone ring twice, and hangs up.

2
.

The helper must call the panel again

in 10 to 40 seconds. The panel answers
System hello. This works if you have a phone interface voice module (part
#60
-
777
-
01) installed.

3
.

The helper dials the following on the phone, #, 1234, #, 8 (
AVM access
CODE
), 5.

4
.

The helper should now be able to hear you through the AVM.

5
.

Walk through the vicinity of the AVM while speaking at a normal conversation
level.

6
.

Tell the helper to dial a 1 and speak to you. To return to listen mode, the

helper dials a 3.

7
.

When testing is complete, have the helper dial 99 and hang up.

To test the module with the central station:

1
.

Inform the central station that you will be sending an alarm and testing an
AVM.

2
.

Give them the programming selections you made for the panel.

3
.

Use a panic button to initiate an auxiliary alarm.
C
hapter 4
:
Testing and troubleshooting

104

Concord 4 Installation Manual

4
.

The central station operator waits for the alarm to be reported and initiates an
audio session.

5
.

Walk through the vicinity of the AVM while speaking at a normal conversation
level.

6
.

Have the operator speak to you.

7
.

When testing is complete, the operator will end the session.

Cellular backup commu
nication

To check the cellular communication between the panel and the central
monitoring station:

1
.

Contact the central monitoring station to inform them that you are testing the
system.

2
.

Install and activate the Super
Bus 2000 cellular backup module.

3
.

Verify or change the following CS phone panel option settings shown in

Cellular backup commu
nication

above
.

Note:
If the current setting
s do not match the test settings, record the current
settings (
Table

17

on page 101
), so that they can be restored when this test is
complete.

4
.

Disconnect the phone line by
unplugging the DB
-
8 cord from the RL 31X jack.

5
.

Initiate a phone test (8,
system master code
, 2).

6
.

The phone test attempt should fail via the phone line within 5 minutes. The
panel will emit a long low tone (and speak “p
hone failure 1” if so equipped).

7
.

Wait for the phone test to succeed via the cell backup. The panel should emit
a short high tone (and speak “phone test okay” if so equipped).

8
.

Verify the CS report.

9
.

If

success does not occur, verify that the signal strength (RSSI) shown on the
cellular backup module is acceptable and repeat the process.

Table

18
: Cellular backup communication

CS phone 1 option

Test setting

Previous setting

Phone

number

Central station phone number


High level reports

On


Backup

Off*


Cellular backup

On


*Can be set to On if no CS phone 2 phone number is programmed.

Chapter 4
:
Testing and troubleshooting

Concord 4 Installation Manual

105

Chapter 4
:
Testing and troubleshooting

106

Concord 4 Installation Manual

Troubleshooting

This section provides information to help you diagnose and solve various
pro
blems that may arise while configuring or using your UTC Fire & Security
product.




Panel power issues

below




Access code issues

on page 108




Arming and disarming issues

on page 108




Bypassing issues

on page 109




Wireless sensor and touchpad battery issues

on page 109




Central station/pager reporting issues

on page 109




Alphanumeric touchpad issues

on page 110




Fixed display touchpad iss
ues

on page 110




Speaker issues

on page 111




Siren issues

on page 111




Hardwired zone issues

on page 112




Wireless sensor zone issues

on page 112




Wireless touchpad issues

on page 113




Phone issues

on page 113




Light control issues

on page 114




Energy saver module issues

on page 114




Automation module issues

on page 1
15

Panel power issues

Concord 4 transformers

Concord 4 uses a 16.5 VAC transformer, (600
-
1023 or 600
-
1024 with power line
carrier). Concord 3 uses a 24 VAC transformer
. Using a 24 VAC transformer on
Concord 4 damages the panel.

The panel does not power up and touchpads don’t display or respond.



Verify that the panel transformer is plugged into an unswitched outlet.



Check the AC circuit breaker to be sure the circui
t is live.



Check that the backup battery is installed correctly and the AC power
transformer is plugged in.



Check for proper panel and transformer wiring.



Measure the incoming AC voltage at panel terminals 1 and 2. It should read
about 16.5 VAC.


Chapter 4
:
Testing and troubleshooting

Concord 4 Installation Manual

107


No

incoming AC voltage at panel terminals 1 and 2.

1
.

Unplug the AC power transformer and disconnect the wires from the
transformer and the panel.

2
.

Check transformer to panel wire for short or open circuits.

3
.

Plug in the transformer and check for 16.5 VAC at the transformer
unconnected terminals. If it shows zero (0) volts, replace the transformer.

WARNING:
Do not check for voltage by touching two live wires together. This
may damage the transformer.

Touch
pad display indicates System Low Battery or voice sounds, “System
low battery.”



Check that the backup battery is installed correctly and the AC power
transformer is plugged in.



Measure the incoming AC voltage at panel terminals 1 and 2. It should read
about 16.5 VAC.



Check for 11.75 to 13.8 VDC battery voltage between the backup battery
spade lugs. If the battery voltage is not within this range, replace the battery.

Note:
When the panel is running a backup battery test, the reading at the
connected b
attery can range from 11.2 to 13.5 VDC. The panel automatically
runs a backup battery test under the following conditions: (1) on initial power
-
up,
(2) during user sensor test, (3) once every minute when backup battery has
failed, (4) once every 24 hours a
t the programmed STIME (UL 98 Options off) or
once every 4 hours (UL 98 Options on).

With the AC power transformer plugged in, the panel automatically charges the
battery. While the battery is charging for the first time, it is normal for the system
to ind
icate System Low Battery. This can take a number of hours depending on
the initial battery charge. Once the battery reaches 12.5 VDC (full charge as
measured while in battery test), the condition clears. If the trouble condition
persists after 24 hours, re
place the backup battery.

The touchpads flash AC or display AC Power Failure/AC Failure After
pressing STATUS the panel continues to operate from backup battery.



Check the AC circuit breaker to be sure the circuit is live.



Check for proper panel and tr
ansformer wiring.



Check that the transformer is plugged into a nonswitched outlet and secured
with the provided screw.
Chapter 4
: Testing and troubleshooting

108

Concord 4 Installation Manual



Check that the transformer is supplying AC to the panel.

WARNING:
Be careful when securing the transformer to an outlet with a metal
cover. Hold the cover tightly in place. You could receive a serious shock if the
metal outlet cover drops down onto the prongs of the plug while you are securing
the transformer and cover to the outlet box.

Access code issues
Customer cannot remember access codes.


Check your records to see if you have the customer’s access codes on file.



Verify the acce
ss
codes using the Enterprise Downloader software.


Clear memory and reprogram the panel locally. Clearing the memory erases
all programming.
Installer cannot remember install code.


Check
your records to see if you have the install code on file.


Verify the install code using the Enterprise Downloader software.


Use the dealer code to enter program mode and view the installer code.
Installer cannot remember dealer code.

Check your records to see if you have the dealer code on file. If you don’t have
dealer codes, you need to replace the panel.
Arming and disarming issues
System protests and won’t arm.



If arming to level 2, make sure all monitored perimeter doors and windows are
closed.


If arming to level 3, make sure all perimeter and interior sensors are closed.


Press
STATUS for an indication of the problem.
System won’t disarm.



Acce
ss
code is not programmed or set up in user programming to disarm
system. Wireless
touchpad is not learned into system or hardwired touchpad
is not communicating to panel.


System won’t
arm to Level 3 away when arming from a touchpad.
It does arm to Level 3 (away) with a keyfob or 3rd party mobile app.


The installer code is being used to disarm the system. The system is
designed not to disarm using the installer code. Use a regular or system
master code to disarm the system.


You may be trying to disarm using an incorrect code. Verify correct code and
enter it.


When arming to Level 3 (away) you must exit through a standard exit delay door.
If not the system will arm to Level 2 (Stay)
.

Chapter 4
: Testing and troubleshooting

Concord 4 Installation Manual

109

Bypassing issues

Touchpad indicates Invalid and/or “Invalid” is heard when you attempt to
bypass a sensor.



You may be attempting to b
ypass a 24
-hour sensor that cannot be bypassed
(group 26 fire sensors).



The sensor is not active in the current arming level.



Arm the system to the desired arming level, then bypass.

System cancels sensor bypass when you try to arm to Level 2 or 3.

Sen
sor is being bypassed before arming to Level 2 stay or Level 3 away. Arm to
the desired level before bypassing a sensor.

Wireless sensor and touchpad battery issues

System indicates Sensor/Touchpad nn low battery.

Replace the indicated device battery and t
est the sensor/touchpad after replacing
the battery.

Central station/pager reporting issues

Trouble with your central station or pager.

Check the programming, panel connections, and proper phone line with line
seizure.

To check your programming:

1. Make sure you enter the correct phone number.

2. Make sure you enter the correct account number.

3. Check that the appropriate format is chosen (SIA or CID).

4. Make sure the appropriate reports ar
e turned on.

To check your panel connections:

1. Concord panels are polarity sensitive, so check for proper polarity:

The positive green lead or (TIP) wires must connect to terminal 25 on the
board.
Chapter 4
:
Testing and tr
oubleshooting

110

Concord 4 Installation Manual

The negative red lead or (RING) wires m
ust connect to terminal 28 on the
board.

2
.

Concord panels are voltage sensitive, so it’s necessary to check for proper
voltage:

On hook voltage should be approximately 48
-
52 volts.

Off hook voltage should be approximately 6
-
10 volts.

Note:

The Concord panel has a built
-
in line voltage meter. If it does not see
proper voltage, it will not dial on a tone phone line. This does not apply to a pulse
phone line.

To check proper phone line with line seizure:

1
.

Check the type of
phone line. Concord panels work with analog phone lines
or DSL with a DSL filter inline to the panel. VOIP or digital phone lines may
not work with the panels.

2
.

Check that the premise’s phone line is working.

3
.

Check that

the DB
-
8 cord is plugged into the RJ31X/CA
-
38A jack.

4
.

Check for correct phone line wiring between the TELCO block and the
RJ31X/CA
-
38A jack.

Alphanumeric touchpad issues

Display shows all ************.

Touchpad is not connected to panel
bus terminals or is wired incorrectly. Check
and correct wiring.

Display is blank.



Check that panel is powered up.



Check for touchpad power and/or incorrect bus wiring, opens, or shorts.



Check the touchpad brightness setting. (See Options menu on pag
e

108.)

Touchpad buttons don’t beep when pressed.



Check for touchpad power and/or incorrect bus wiring, opens, or shorts.



Check that key beeps option is set to on. (See the Accessory modules
-

bus
device settings on page

93.)

Fixed display touchpad iss
ues

Display is lit but does not respond to key presses.

Chapter 4
:
Testing and troubleshooting

Concord 4 Installation Manual

111



Touchpad is not connected to panel bus terminals or is wired incorrectly.
Check and correct wiring.



Check that touchpad is learned into panel memory.

Display is blank.



Check that panel is powere
d up.



Check for touchpad power and/or incorrect bus wiring, opens, or shorts.



Check the touchpad brightness setting. (See the user
-
programming Options
menu on page

108.)

Touchpad buttons don’t beep when pressed.



Check for touchpad power and/or incorr
ect bus wiring, opens, or shorts.



Check that key beeps option is set to on. (See the Accessory modules
-

bus
device settings on page

93.)

Speaker issues

Speakers don’t sound alarms.



Speaker output has shut down because panel detected terminal 7 or 8 is

shorted to ground. Disconnect panel AC and battery backup power. Locate
short and correct. Apply panel AC and backup battery power and retest.



Alarm is in partition 2 to 6 and speaker is connected to panel terminals 7 and
8, which activate only for part
ition 1 alarms.

Siren issues

Piezo sirens connected to SnapCard, or onboard (panel) outputs 1 and/or 2
don’t produce any alarm sounds.



Check for incorrect wiring between siren and panel, and correct where
necessary.



Output has not been configured (set
up) to activate sirens. Enter program
mode and configure output. (See Accessory modules
-

bus device settings on
page

93.)



Check for correct output partition assignment.



Check that your wires are connected to the appropriate terminals:

Output 1 (exteri
or) uses terminals 9 (positive) and 13 (ground).

Output 2 (interior, follows status beeps) uses terminals 11 (positive) and 10
(ground).
Chapter 4
:
Testing and troubleshooting

112

Concord 4 Installation Manual

Hardwired zone issues

System doesn’t go into alarm when zone is tripped.



System is disarmed. Arm system and then trip

the zone.



Zone is not learned into panel memory. Enter installer/dealer program
mode

LEARN SENSORS, and learn zone into memory.



Zone is learned into wrong partition. Delete zone and learn into correct
partition or change the partition in the EDIT SENS
ORS menu.



For Hardwire Input Module (HIM) zones, check that the HIM LED is blinking to
verify communication with the panel. If LED is off, check wiring between HIM
and panel.

Zone reports trouble condition.



Check that onboard, HIM, and SnapCard zone in
puts have a 2 kohm EOL
resistor installed at the last device on the loop in series for NC loops, in
parallel for NO loops.



Check for zone wire fault

short circuit on NC loops, open circuit on NO
loops.

Wireless sensor zone issues

System doesn’t respond (
in sensor test or when armed) when sensor is
tripped.



Verify that receiver antennas are routed through holes on top of enclosure
and antenna shrouds are installed.



Check that the wireless sensor batteries are installed.



Check the sensor batteries for

low voltage. Replace batteries if necessary.



Use an RF Sniffer (60
-
401) to verify that sensor is transmitting.



Sensor is not learned into panel memory. Enter installer/dealer program
mode

LEARN SENSORS, and learn sensor into memory.



Zone is learned
into wrong partition. Delete zone and learn into correct
partition or change the partition in the EDIT SENSORS menu.

Sensor reports trouble condition.



Sensor tamper switch is tripped

sensor cover is off, not latched securely, or
sensor is not mounted sec
urely. Secure sensor mounting and/or cover, then
trip sensor to clear the condition.



Check the sensor battery for low voltage. Replace batteries, if necessary.

Chapter 4
:
Testing and troubleshooting

Concord 4 Installation Manual

113

Touchpad indicates [sensor #] supervisory.



Use an RF Sniffer (60
-
401) to verify that sensor
is transmitting. If sensor is
not transmitting, check battery for low or no voltage and replace.



Change mounting position of sensor (from horizontal to vertical or vice versa)
and test sensor several times for consistency.



Sensor signal is not reaching

panel/receiver because sensor is too far away.
Remove sensor from mounted location and test from other locations. Mount
sensor in area where signal can reach panel/receiver or install a SuperBus
2000 RF transceiver near the sensor. You may also install a
Repeater 80
-
922
-
1 to boost signal.

Smoke sensor beeps intermittently.

Sensor batteries are getting low. Replace batteries.

Wireless touchpad issues

System doesn’t respond to commands entered from wireless touchpad.



Verify that receiver antennas are route
d through holes on top of enclosure
and antenna shrouds are installed.



Check that touchpad batteries are properly installed.



Check the touchpad batteries for low voltage. Replace batteries, if necessary.



Use an RF Sniffer (60
-
401) to verify that touc
hpad is transmitting.



Touchpad is not learned into panel memory. Enter program mode and learn
touchpad into memory (see Sensors menu on page

85.



Touchpad is learned into wrong partition. Delete touchpad and learn into
correct partition or change the pa
rtition in the Sensors menu on page

85.

Touchpad reports trouble condition.

Check the touchpad batteries for low voltage. Replace batteries, if necessary.

Phone issues

Loss of dial tone at onsite phones after wiring RJ31X jack or connecting
the DB
-
8 cord.



Wait two minutes and try again. The panel may be busy trying to report to the
central station.



Disconnect the panel DB
-
8 cord from the RJ31X jack. If the phone still doesn’t
work, the system is okay and the problem is in the wiring.
Chapter 4
:
Testing and troubleshooting

114

Concord 4 Installation Manual



Check RJ31X jack
wiring and TELCO block wiring. Replace RJ31X jack if
necessary.



Check DB
-
8 cord connections at the panel and RJ31X jack. Replace cord if
necessary.



Perform a phone test after troubleshooting the phone line.

Constant dial tone, preventing dial
-
out on pr
emises phones.

One or more polarity
-
sensitive phones exist on
-
site. Reverse the phone wires
connected to the brown and gray wire terminals on the RJ31X jack.

Light control issues

Light controlled by X10 lamp module is not working.



Partition house codes a
re not programmed into panel. Enter program mode
and set partition house codes.



Check that the HOUSE dial on the X10 module matches the partition house
code programmed into the panel.



Panel is not powered by a power line carrier transformer. Replace ex
isting
transformer with a power line carrier transformer.



Check to make sure X10 module is not plugged into an outlet controlled by a
switch. Move to a nonswitched outlet location and test.



Check that the lamp has a working bulb and that the lamp switc
h is on.



Power transformer and X10 modules are not plugged into outlets on the same
electrical phase. Relocate modules or transformer to different outlets to
determine working locations.

Energy saver module issues

Module does not respond to system comman
ds or appear to control
furnace.



Check that the module is wired correctly to the panel terminals.



Verify the module LED is flashing continuously. If the LED is not flashing,
remove power and check wiring.



There is a 5
-
minute delay after the module re
turns control to the furnace/AC
thermostat, before the module overrides the thermostat again. Wait 5 minutes
and try again.

Module temperature does not match actual room temperature.

Chapter 4
:
Testing and troubleshooting

Concord 4 Installation Manual

115

The module room temperature setting has not been adjusted or was adjusted

before the module warmed or cooled to room temperature. To ensure accuracy,
wait at least 15 minutes after installing the module before adjusting the
temperature. To adjust the module room temperature setting, see Temperature
under “
Accessory modules
-

bus device settings

on page 73
.

Automation module issues

Module is not controlling or communicating with the panel and panel
indicates a “BUS FAILURE UNIT nn” where nn is the automation modul
e
bus unit number.



Check that the module is wired correctly to the panel terminals.



Verify the SuperBus module’s red LED is flashing continuously. If the LED is
not flashing, remove power and check wiring.



Check that the RS
-
232 cable is firmly connec
ted to the automation module
and the automation device.



Verify the automation device is powered and turned on.

Module is not controlling or communicating with the panel and panel does
not indicate a bus failure.

Verify the automation module is learned in
to panel memory.


Concord 4 Installation Manual

117

Appendix

A

System planning sheets

Summary

This appendix provides various system planning sheets for the Concord 4.

Content

Error! Bookmark not
defined.
Appendix A
:
System planning sheets

118

Concord 4 Installation Manual

Customer information

Table

19
: Customer information

Customer name


Address


City



County


State



Zip


Phone



Wireless devices

Table

20
: Wireless devices

Part number

Description

Quantity

60
-
362

Door/window sensor


60
-
670
-
95R

SAW door/window sensor


60
-
741
-
95

Micro recessed door/window sensor


60
-
499

Slim line door/window sensor


60
-
688

Micro door/window sensor


60
-
641

Long
-
life door/window sensor


60
-
461

Shock sensor


60
-
459

Sound s
ensor


60
-
462

Glass guard sensor


60
-
506

System sensor smoke sensor


60
-
838
-
95R

2100ARFT smoke sensor


60
-
848
-
02
-
95

ESL 562 smoke sensor


60
-
460

Rate
-
of
-
rise heat sensor


60
-
589

Manual fire pull sensor


60
-
504

Freeze sensor


60
-
452

Pendant panic se
nsor


60
-
458

Single button panic sensor


Appe
ndix A
:
System planning sheets

Concord 4 Installation Manual

119

Part number

Description

Quantity

60
-
457

Dual button panic sensor


60
-
578

Water
-
resistant panic sensor


60
-
511
-
01
-
95

DS924i PIR motion sensor


60
-
639
-
95R

SAW indoor PIR motion sensor


60
-
639
-
95R
-
OD

SAW outdoor PIR motion sensor (not for
intrus
ion protection)


60
-
703
-
95

Crystal indoor PIR motion sensor


60
-
834
-
95R

Adjustable dual technology sound sensor


60
-
597

HiTech handheld wireless touchpad


60
-
607

Two
-
button keyfob touchpad


60
-
606

Four
-
button keyfob touchpad


60
-
659
-
95R

SAW four
-
but
ton keyfob touchpad


60
-
832
-
95R

Two
-
button ELM keyfob touchpad



Hardware devices

Table

21
: Hardware devices

Part number

Description

Quantity

mA
(max.)

Subtotal

Hardwire sensors/detectors

System sensor models 2400, or 2400TH or
ESL series
429AT, 429C, 429CT, 521B, 521BXT, 521NCSXT, 711U,
711UT, 721U, 721UT, TS7
-
2, or TS7
-
2T


80 mA*


13
-
082

PIR motion detector


10 mA


Sirens

13
-
046

Hardwire exterior siren


145 mA


13
-
949

Hardwire interior siren


85 mA


13
-
950

Piezo dynamic ex
terior siren


150 mA


SuperBus 2000/miscellaneous components

60
-
746
-
01

2x16 LCD alphanumeric touchpad


90 mA


60
-
820

Fixed display LCD touchpad


65 mA


600
-
1020

FTP 1000


75 mA


60
-
803

2x20 LCD alphanumeric touchpad


120 mA

Appendix A
:
System planning sheets

120

Concord 4 Installation Manual

Part number

Description

Quantity

mA
(max.)

Subtotal

60
-
804

2x20 VFD alphanume
ric touchpad


120 mA


60
-
983

ATP 1000


110 mA


60
-
984

ATP 2600


165 mA


60
-
985

ATP 2100


300 mA


600
-
1013

GTS 50


300 mA


60
-
836

Voice only module (with current jumper
installed) / (with current jumper removed)


300 mA /
600mA


60
-
777
-
01

Phone interf
ace/voice module


600 mA


600
-
1019

2
-
amp power supply


N/A


60
-
756

4 input/2 output SnapCard


185 mA


60
-
757

8Z hardwired zone expander SnapCard


230 mA


60
-
758

4 output SnapCard


130 mA


60
-
774

Hardwired input module


35 mA


60
-
770

Hardwired output
module


180 mA


60
-
620
-
01

Energy saver module


20 mA


60
-
850

60
-
850
-
01

Cellular backup module (standard power)

Cellular backup module (high power)


10 mA


60
-
861

Wireless cellular gateway


1900 mA


60
-
677

Interrogator 200 audio verification module


160
0 mA


60
-
783
-
02

Automation module


10 mA


60
-
528

Hardwired interior speaker


35 mA


13
-
060

15
-
watt speaker


500 mA


Total power consumption:

Total power consumption not to exceed:

mA

1,000 mA

* Total current only for all two
-
wire smoke detectors conn
ected to panel two
-
wire smoke loop.


Appendix A
:
System planning sheets

Concord 4 Installation Manual

121

Zone and sensor assignments

Table

22
: Zone and sensor assignments

No.

RF zone

Module
bus ID
number

Module
input
number

Group

Partition

Zone/sensor text

1







2







3







4







5







6







7







8







9







10







11







12







13







14







15







16







17







18







19







20







21







22







23







24







25







26







27







28







29






Appendix A
:
System planning sheets

122

Concord 4 Installation Manual

No.

RF zone

Module
bus ID
number

Module
input
number

Group

Partition

Zone/sensor text

30







31







32







33







34







35







36







37







38







39







40







41







42







43







44







45







46







47







48







49







50







51







52







53







54







55







56







5
7







58







59







60







61







Appendix A
:
System planning sheets

Concord 4 Installation Manual

123

No.

RF zone

Module
bus ID
number

Module
input
number

Group

Partition

Zone/sensor text

62







63







64







65







66







67







68







69







70







71







72







73







74







75







76







77







78







79







80







81







82







83







84







85







86







87







88







89







90







91







92







93






Appendix A
:
System planning sheets

124

Concord 4 Installation Manual

No.

RF zone

Module
bus ID
number

Module
input
number

Group

Partition

Zone/sensor text

94







95







96








System settings index and record

Table

23
: System settings index and record

Setting refe
rence (default)

Shortcut number

Setting

Installer programming

8,

installer/dealer code
, 00

24
-
hour tamper (Off)

06000


AC failure (Off)

06011


Access code lock (On)

0003


Access timeout (90 seconds)

09004


Account number (00000)

0010 to 0060


Activi
ty timeout (24 hours)

0305


Alarm verify (Off)

06108 to 06608


Antenna tamper (Off)

06001


Audio mode (1)

09001


Audio verify (Off)

09000


Auto phone test (Off)

02001


Auto test reset (On)

02002


Auxiliary panic (On)

0511 to 0561


Auxiliary power f
ail (On)

06016


AVM access code (None)

09006


Back in service (On)

06003


Backup CS phone 1 (On)

CS phone 2
-
3 (Off)

01005,

01015, 01025

1__________

2__________ 3__________

Battery restoral (Off)

06006


Beep delay (2 seconds)

09005


Buffer control (O
ff)

06002


Buffer full report (Off)

06007


Appendix A
:
System planning sheets

Concord 4 Installation Manual

125

Setting refe
rence (default)

Shortcut number

Setting

Bypass reports (Off)

06004


Call wait cancel (None)

02009


Cancel message (On)

02007


Cellular backup CS phone 1 (On),

CS phone 2
-
3 (Off)

01007,

01017, 01027

1__________

2__________ 3__________

Cellular sys
tem (B)



Closing reports (Off)

06101
-

06601


Comm. failure (On)

02003


CS phone 1 to 3 (None)

01000, 01010, 01020


Daylight saving (On)

0307


Dealer code (None)

0002


Delete sensors (None)

082


Dial tone detect (On)

02010


Dial abort delay (30 se
conds)

02006


Disable trouble beeps (Off)

0701


Downloader code (12345)

0000


Downloader phone number (None)

01090


DTMF dialing (On)

02004


Duress code (None)

0016 to 0066


Duress option (Off)

06103 to 06603


Edit sensors (None)

083


Entry delay (
30 seconds)

0310 to 0360


Exception reports phones (Off)

01003,

01013, 01023

1__________2__________

3__________

Exception reports pagers (Off)

01033, 01043,

01053, 01063,

01073

1__________2__________

3__________4__________

5__________

Exit delay (60 sec
onds)

0311 to 0361


Exit extension (On)

0013 to 0063


Extended delay (4 minutes)

0312 to 0362


Fire panic (On)

0510 to 0560


Fire shutdown (Off)

09002


Force armed (Off)

06104 to 06604


Freeze alarm (Off)

06106 to 06606


Freeze temp (42)

06107 to 06
607

Appendix A
:
Syste
m planning sheets

126

Concord 4 Installation Manual

Setting refe
rence (default)

Shortcut number

Setting

Global fire (Off)

0703


Ground fault (On)

06017


High level reports (phones) CS phone 1
(On), CS phone 2
-
3 (Off)

01001, 01011,

01021

1__________2__________

3__________

High level reports pagers (On)

01031, 01041,

01051, 01061,

01071

1__________2__
________

3__________4__________

5__________

House code (1B, 2C, 3D, 4E, 5F, 6G)

0401 to 0451


Immediate beeps (Off)

0700


Installer code (4321)

0001


Keyfob arming (Off)

0513 to 0563


Keyfob PTN

0006


Keyswitch sensor (None)

0014 to 0064


Keyswitch
style (Transition)

0015 to 0065


Latchkey format (Off)

06105 to 06605


Latchkey reports pagers (On)

01035, 01045,

01055, 01065,

01075

1__________2__________

3__________4__________

5__________

Latchkey zones (None)

0500


Learn sensors (None)

080


Line
fail delay (None)

0213


Local phone control (On)

0210 to 0260


Low CPU battery (On)

06005


Low level reports CS phone 1 (On), CS
phone 2
-
3 (Off)

01002, 01012,

01022

1__________2__________

3__________

Low level reports pagers (Off)

01032, 01042,

01052,
01062,

01072

1__________2__________

3__________4__________

5__________

Manual mic gain

09009


Multiple
-
partition arm (Off)

0005


Next phone test (7 days)

0304


No activity (Off)

06102 to 06602


Open/close reports phones (Off)

01004, 01014,

01024

1____
______2__________

3__________

Open/close reports pagers (Off)

01034, 01044,

01054, 01064,

01074

1__________2__________

3__________4__________

5__________

Appendix A
:
System planning sheets

Concord 4 Installation Manual

127

Setting refe
rence (default)

Shortcut number

Setting

Opening reports (Off)

06100 to 06600


Onboard output 1 (01614
-

any audible
alarm)

11101


Onboard
output 2 (01710
-

status and
alarm tones)

11111


Output trip time (4 seconds)

0305


Pager delay (15 seconds)

02008


Pager partition assignment (1)

01037, 01047,

01057, 01067,

01077

1__________2__________

3__________4__________

5__________

Pager phone 1

to 5 (None)

01030, 01040,

01050, 01060,

01070

1__________2__________

3__________4__________

5__________

Partition security (On)

0004


Phone access key (#)

0216 to 0266


Phone panic (Off)

0215 to 0265


Phone test (On)

02000


Phone test frequency (7 da
ys)

0303


Police panic (On)

0512 to 0562


Program report (Off)

06015


Quick arm (Off)

0011 to 0061


Quick exit (On)

0012 to 0062


Receiver failure (Off)

06012


Remote access (On)

0211 to 0221


RF low battery rpt (Weekly)

06013


RF supervisory rpt (
Weekly)

06014


RF TX timeout (12 hours)

0302


Ring/hang/ring on

0212 to 0262


Reporting format (SIA/CID)

01006, 01016,

01026

1__________2__________

3__________

Sensor text (None)

081


Silent talkback (Off)

09003


Siren timeout (4 minutes)

0313 to 036
3


Siren verify (Off)

0710


Sleep time (Off)

0314 to 0364


Smoke verify (Off)

1100

Appendix A
:
System planning sheets

128

Concord 4 Installation Manual

Setting refe
rence (default)

Shortcut number

Setting

SnapCard output 1 (01400
-

keyfob star
button activation)

101101


SnapCard output 2 (00410
-

any audible
alarm)

101111


SnapCard output 3 (00903
-

arming to
stay or a
way)

101121


SnapCard output 4 (01003
-

arming to
away)

101131


Star is no delay (Off)

0514 to 0564


Streamlining (On)

01036, 01046,

01056, 01066,

01076

1__________2__________

3__________4__________

5__________

Supervisory time (03:00)

0300


Swinger l
imit (1)

06015


System tamper (Off)

06109 to 06609


Toll saver (On)

0214 to 0264


TP panic RPT FMT (Off)

06010


Two
-
trip error (Off)

06009


Two
-
wire smoke (Off)

1101


UL 98 options (Off)

0702


VOX gain range

09008


VOX mic gain

09007


VOX RX gain

09010


Zone restorals (Off)

06008




Concord 4 Installation Manual

129

Appendix

B

Reference tables

Summary

This appendix provides reference tables and specifications.

Content

Error! Bookmark not def
ined.
Appendix B
: Ref erence tables

130

Concord 4 Installation Manual

Sensor group characteristics

Table
24
below
shows what the sensors on your Concord 4 system do. Every
sensor is assigned to a group, and this table specifies those groups and
functio
ns. Every device must be assigned to one of these groups.

Table
24: Sensor group characteristics

#

Name

Application

Alarm

Delay




Restoral

Supervisory

CS Report

Chime
(Level)

Active levels

00

Fixed
panic

24
-
hour audible fixed
emer
gency buttons.

Police

Instant







1,2,3

01

Portable
panic

24
-
hour audible portable
emergency buttons.

Police

Instant






1,2,3

02

Fixed
panic

24
-
hour silent fixed
emergency buttons.

Silent

Instant







1,2,3

03

Portable
panic

24
-
hour silent portable
emergency buttons.

Silent

Inst
ant






1,2,3

04

Fixed
auxiliary

24
-
hour auxiliary sensor,
such as Pendant Panic or
holdup button.

Auxiliar
y

Instant







1,2,3

05

Fixed
auxiliary

24
-
hour auxiliary
emergency button. Siren
shutoff confirms CS report.

Auxiliar
y

Instant







1,2,3

06

P
ortable
auxiliary

24
-
hour portable auxiliary
alert button.

Auxiliar
y

Instant






1,2,3

07

Portable
auxiliary

24
-
hour portable auxiliary
button. Siren shutoff
confirms CS report.

Auxiliar
y

Instant






1,2,3

08

Special
intrusion

Special belongings, such
as gun cabinets and wall
safes.

Police

Instant








1,2,3

09

Special
intrusion

Special belongings (i.e.
gun cabinets and wall
safes.)

Police

Standar
d








1,2,3

10

Entry/

exit delay

Entry and exit doors that
require a standard delay
time.

Police

Stan
dar
d









2,3

11


Garage doors and
entrances that require an
extended delay time.

Police

Extende
d









2,3

Supplemen­
tary Exten­
ded Delay
1
Appendix B
: Ref erence tables

Concord 4 Installation Manual

131

#

Name

Application

Alarm

Delay




Restoral

Supervisory

CS Report

Chime
(Level)

Active levels

12

Supplemen­
tary Exten­
ded Delay


Driveway
gates and
entrances that require a
twice extended delay time.

Police

Twice
extende
d









2,3

13

Instant
perimeter

Exterior doors and
windows

Police

Instant









2, 3

14

Instant
interior

Interior doors (Hardwired)

Police

Follower








2,3

15

Instant
interior

Interior PIR motion
sensors. (RF wireless)

Police

Follower







2,3

16

Insta
nt
interior

Interior doors. (Hardwired)

Police

Follower








3

17

Instant
interior

PIR motion sensors (RF
wireless.)

Police

Follower







3

18

Instant
interior

Instant interior cross
-
zone# PIR motion
sensors. *

Police

Follower







3

19

Delayed
in
terior

Interior doors that initiate a
delay before going into
alarm.

Police

Interior








3

20

Delayed
interior

PIR motion sensors that
initiate a delay before
going into alarm.

Police

Standar
d







3

21

Local
instant
interior

24
-
hour local alarm zo
ne
protecting anything that
opens and closes.

Police

Instant







1,2,3

22

Local
delayed
interior

Same as group 21, plus
activation initiates a delay
before going into alarm.

Police

Standar
d







1,2,3

23

Local
instant
auxiliary

24
-
hour local alarm zon
e
protecting anything that
opens and closes.

Auxiliar
y

Instant







1,2,3

24

Local
instant
auxiliary

24
-
hour local alarm zone
protecting anything that
opens and closes. Sirens
shut off at restoral.

Auxiliar
y

Instant







1,2,3

25

Local
special
chime

Notify the user when a
door is opened. Sounds
emit from a local
annunciator.

Special
chime

Instant






1,2,3

1 Appendix B
: Ref erence tables

132

Concord 4 Installation Manual

#

Name

Application

Alarm

Delay




Restoral

Supervisory

CS Report

Chime
(Level)

Active levels

26

Fire

24
-
hour fire, rate
-
of
-
rise
heat, and smoke sensors.

Fire

Instant








1,2,3

27

Output
module

Hardwire Output Module
(HOM) lamp contro
l or
other customer feature.

Silent

Instant







1,2,3

28

Output
module

HOM, PIR motion sensor,
sound sensor or pressure
mat.

Silent

Instant






1,2,3

29

Auxiliary

Freeze sensor.

Auxiliar
y

Instant








1,2,3

32

Output
module

HOM, PIR motion sensor
,
sound sensor or pressure
mat.

Silent

Instant





1,2,3

33

Siren

Wireless siren supervision.

Silent

Instant







1,2,3

34

Gas

Carbon monoxide (CO)
gas detectors

Auxiliar
y

Instant








1,2,3

35

Local
instant
police
(day
zone)

Local alarm in levels
1 and
2. Report to CS in level 3.

Police

Instant







(Lev
el 3
only
)


1,2,3

38

Auxiliary

Water sensor.

Auxiliar
y

Instant








1,2,3

Note: Check marks (

) represent characteristics present in a group.

* Sounds instant police siren if two or more senso
rs are tripped within 4 minutes. Otherwise,
sensors are followers to delayed sensors. If Alarm Verification is on, group 18 functions like group
17.


1. Does not satisfy Auto Stay Arming exit requirement


Appendix B
: Ref erence tables

Concord 4 Installation Manual

133

Cross
-zoning

Cross
-zoning
(two
-trip) refers to two different group 18 sensors that must be
tripped within
two minutes of each other to report an alarm to the central station.
Figure
28
below
shows the path of a person walking from the kitchen to the living
room. When the person is detected walk
ing through the kitchen, the motion
sensor in the kitchen is tripped, sounding a local alarm. If motion is detected by
the living room motion sensor within two minutes, an alarm report will be sent to
the central station.

Figure 28: Cross-zone diagram

Note:
We do not recommend cross-zoning for exit/entry zones. Each zone can
individually protect the intended area.
Extended Delay Zones

Note:
The Auto Stay Arming feature can be disabled user the Enterprise Download
Software. Please refer to the "Downloading" section of this manual.

Sensor groups 10, 11 and 12 were designed as one path.The system will arm
various areas as you leave the premises.
Example: Exiting the premise.
1. Open and close the premise entry exit door (Group 10).
The system arms premise after the Standard delay has expired. (30­240 secs)
2. Open and close a garage door (Group 11). System adds this zone to the
already armed system at the end of the extended delay time. (1­8 mins)
3. Drive over a driveway sensor (Group 12). System adds this zone to the
already armed system and the end of the twice extended delay time. (2­16 mins)
Upon entering
,
the system uses the lowest entry time as a zone is opened.

Example: Entry exit door (Group 10) entry time is programmed for 30 secs and
Garage door (Group 11) entry time is programmed for 6 mins.
1. When the garage door
has been opened
the panel
must be disarmed within 6 minutes.
2. If the entry exit door
is opened
after 2

min
utes
the entry exit (Group 10) delay
starts.
T
he panel
must be disarmed within 30 seconds
. There must be a Sensor Group
10 zone used with either a Sensor Group 11 or 12 zone for the system to arm to
Level 3 (away) from a touchpad. This is due to the Auto Stay Arming option that
is enabled in the system.
Appendix B
:
Ref erence tables

134

Concord 4 Installation Manual

Sensor text

Table

25

below

provides sensor text wit
h the applicable item number.

Table

25
: Item numbers and sensor text

Item #

Sensor text

Item
#

Sensor text

Item
#

Sensor text

Item
#

Sensor text

001

Aborted

061

Entry

121

North

181

Up

002

AC

062

Error

122

Not

182

West

003

Access

063

Exit

123

Now

183

Window

004

Active

064

Exterior

124

Number

184

Zone

005

Activity

065

Factory

125

Off

185

0

006

Alarm

066

Failure

126

Office

186

1

007

All

067

Family

127

OK

187

2

008

AM

068

Father’s

128

On

188

3

009

Area

069

Feature

129

Open

189

4

010

Arm

070

Fence

130

Opening

190

5

011

Armed

071

Fire

131

Panic

191

6

012

Arming

072

First

132

Partition

192

7

013

Attic

073

Floor

133

Patio

193

8

014

Auxiliary

074

Force

134

Pet

194

9

015

Away

075

Foyer

135

Phone

195

A

016

Baby

076

Freeze

136

Pl
ease

196

B

017

Back

077

Front

137

PM

197

C

018

Bar

078

Furnace

138

Police

198

D

019

Basement

079

Gallery

139

Pool

199

E

020

Bathroom

080

Garage

140

Porch

200

F

021

Battery

081

Gas

141

Power

201

G

022

Bedroom

082

Glass

142

Press

202

H

023

Bottom

083

Goodbye

143

Program

203

I

024

Breezeway

084

Hallway

144

Progress

204

J

025

Building

085

Heat

145

Quiet

205

K

026

Bus

086

Hello

146

Rear

206

L

027

Bypass

087

Help

147

Receiver

207

M

028

Bypassed

088

High

148

Report

208

N

Appendix B
:
Ref erenc
e tables

Concord 4 Installation Manual

135

Item #

Sensor text

Item
#

Sensor text

Item
#

Sensor text

Item
#

Sensor text

029

Cabinet

089

Home

149

RF

2
09

O

030

Canceled

090

House

150

Right

210

P

031

Car

091

In

151

Room

211

Q

032

Carbon
Monoxide

092

Install

152

Safe

212

R

033

Central

093

Interior

153

Schedule

213

S

034

Chime

094

Intrusion

154

Screen

214

T

035

Closed

095

Invalid

155

Second

215

U

03
6

Closet

096

Is

156

Sensor

216

V

037

Closing

097

Key

157

Service

217

W

038

Code

098

Kids

158

Shed

218

X

039

Computer

099

Kitchen

159

Shock

219

Y

040

Control

100

Latchkey

160

Side

220

Z

041

Date

101

Laundry

161

Siren

221

(space)

042

Daughters

102

Left

162

Sliding

222

‘(apostrophe)

043

Degrees

103

Level

163

Smoke

223

-

(dash)

044

Delay

104

Library

164

Sons

224

_(underscore)

045

Den

105

Light

165

Sound

225

*

046

Desk

106

Lights

166

South

226

#

047

Detector

107

Living

167

Special

227

:

048

Dining

10
8

Load

168

Stairs

228

/

049

Disarmed

109

Loading

169

Stay

229

?

050

Door

110

Low

170

Supervisory



051

Down

111

Lower

171

System



052

Download

112

Main

172

Tamper



053

Downstairs

113

Master

173

Temperature



054

Drawer

114

Mat

174

Test



055

Drive
way

115

Medical

175

Time



056

Duct

116

Memory

176

To



057

Duress

117

Menu

177

Touchpad



058

East

118

Mother’s

178

Trouble



059

Energy Saver

119

Motion

179

Unbypass



060

Enter

120

No

180

Unit



Appendix B
:
Ref erence tables

136

Concord 4 Installation Manual

System event triggers

Table

26

below

describes the system event triggers.

Table

26
: System event trigger

System event

Description

Trigger
number

Null trigger (used for direct control)

Activates only by schedule or d
irect command.

000

Fire alarm

When fire sirens are started.

001

Police alarm

When police sirens are started.

002

Auxiliary alarm

When auxiliary sirens are started.

003

Any audible alarm

When any of the above sirens are started.

004

Silent alarm (senso
r groups 2, 3,
and duress)

When a group 2 or 3 sensor goes into alarm or
when a duress alarm is activated (does not
include groups 25, 27, 28, or 32).

005

Any audible or silent alarm

When any alarm is started (does not include
groups 25, 27, 28, or 32).

0
06

HOM group 27, 28, 32 in alarm

When a sensor in group 27, 28, or 32 goes
into alarm.

007

Major trouble (phone or receiver
failure)

When a receiver failure (S94) or a phone
failure (S96) occurs.

008

Arming to stay or away

When the system is armed to le
vel 2 or 3.

009

Arming to away

When the system is armed to level 3.

010

AVM is interactive (audio session
in progress)

When the central station operator begins
listening or talking to the premises.

011

Fail
-
to
-
communicate (panel can’t
call CS or pager)

When the fail
-
to
-
communicate output is
activated.

012

AVM trip (edge)

When an AVM alarm occurs, output is
activated momentarily.

013

Keychain touchpad star button
-
press

When the star button on a keychain touchpad
is pressed.

014

Smoke power (for resetti
ng four
-
wire smoke detectors)

Deactivated when hardwire smoke detectors
need to be reset.

015

Exterior siren

Activated for police or fire alarms.

016

Interior siren

Activation follows all system noises

017

AVM trip (pulse)

When an AVM alarm occurs, outp
ut is
deactivated for 10 ms

018

State of system status

Follows the state of system status (ready or
trouble).

019

Tamper condition

When any tamper is tripped

020

Appendix B
:
Ref erence tables

Concord 4 Installation Manual

137

System event

Description

Trigger
number

Closing report sent

When a closing report has been successfully
transmitted to the central
station.

021

Arming to Level 1

When the system is disarmed.

022

Group XX in alarm

When any sensor in group XX goes into alarm


Sensor XX in alarm

When sensor number XX goes into alarm


Sensor XX open

When sensor number XX is opened



Sensor group even
t triggers

Table

27

below

describes the sensor group event triggers.

Table

27
: Sensor group event trigger numbers

Sensor group

Trigger number

Sensor group

Trigger num
ber

Group 00 in alarm

064

Group 17 in alarm

081

Group 01 in alarm

065

Group 18 in alarm

082

Group 02 in alarm

066

Group 19 in alarm

083

Group 03 in alarm

067

Group 20 in alarm

084

Group 04 in alarm

068

Group 21 in alarm

085

Group 05 in alarm

069

Grou
p 22 in alarm

086

Group 06 in alarm

070

Group 23 in alarm

087

Group 07 in alarm

071

Group 24 in alarm

088

Group 08 in alarm

072

Group 25 in alarm

089

Group 09 in alarm

073

Group 26 in alarm

090

Group 10 in alarm

074

Group 27 in alarm

091

Group 11 in
alarm

075

Group 28 in alarm

092

Group 12 in alarm

076

Group 29 in alarm

093

Group 13 in alarm

077

Group 30 in alarm

094

Group 14 in alarm

078

Group 31 in alarm

095

Group 15 in alarm

079

Group 32 in alarm

096

Group 16 in alarm

080

Group 35 in alarm

102

Appendix B
:
Ref erence tables

138

Concord 4 Installation Manual

Sensor number event triggers

Table

28

below

describes the sensor number event triggers.

Table

28
: Sensor number event trigger numbers

Sensor number

State

Trigger
n
umber

State

Trigger number

Sensor 01

In alarm

129

Open

257

Sensor 02

In alarm

130

Open

258

Sensor 03

In alarm

131

Open

259

Sensor 04

In alarm

132

Open

260

Sensor 05

In alarm

133

Open

261

Sensor 06

In alarm

134

Open

262

Sensor 07

In alarm

135

Open

26
3

Sensor 08

In alarm

136

Open

264

Sensor 09

In alarm

137

Open

265

Sensor 10

In alarm

138

Open

266

Sensor 11

In alarm

139

Open

267

Sensor 12

In alarm

140

Open

268

Sensor 13

In alarm

141

Open

269

Sensor 14

In alarm

142

Open

270

Sensor 15

In alarm

143

Open

271

Sensor 16

In alarm

144

Open

272

Sensor 17

In alarm

145

Open

273

Sensor 18

In alarm

146

Open

274

Sensor 19

In alarm

147

Open

275

Sensor 20

In alarm

148

Open

276

Sensor 21

In alarm

149

Open

277

Sensor 22

In alarm

150

Open

278

Sensor 23

In
alarm

151

Open

279

Sensor 24

In alarm

152

Open

280

Sensor 25

In alarm

153

Open

281

Sensor 26

In alarm

154

Open

282

Sensor 27

In alarm

155

Open

283

Sensor 28

In alarm

156

Open

284

Appendix B
:
Ref erence tables

Concord 4 Installation Manual

139

Sensor number

State

Trigger
n
umber

State

Trigger number

Sensor 29

In alarm

157

Open

285

Sensor 30

In alarm

158

Open

286

Senso
r 31

In alarm

159

Open

287

Sensor 32

In alarm

160

Open

288

Sensor 33

In alarm

161

Open

289

Sensor 34

In alarm

162

Open

290

Sensor 35

In alarm

163

Open

291

Sensor 36

In alarm

164

Open

292

Sensor 37

In alarm

165

Open

293

Sensor 38

In alarm

166

Open

29
4

Sensor 39

In alarm

167

Open

295

Sensor 40

In alarm

168

Open

296

Sensor 41

In alarm

169

Open

297

Sensor 42

In alarm

170

Open

298

Sensor 43

In alarm

171

Open

299

Sensor 44

In alarm

172

Open

300

Sensor 45

In alarm

173

Open

301

Sensor 46

In alarm

174

Open

302

Sensor 47

In alarm

175

Open

303

Sensor 48

In alarm

176

Open

304

Sensor 49

In alarm

177

Open

305

Sensor 50

In alarm

178

Open

306

Sensor 51

In alarm

179

Open

307

Sensor 52

In alarm

180

Open

308

Sensor 53

In alarm

181

Open

309

Sensor 54

In a
larm

182

Open

310

Sensor 55

In alarm

183

Open

311

Sensor 56

In alarm

184

Open

312

Sensor 57

In alarm

185

Open

313

Sensor 58

In alarm

186

Open

314

Sensor 59

In alarm

187

Open

315

Sensor 60

In alarm

188

Open

316

Sensor 61

In alarm

189

Open

317
Appendix B
:
Ref erence tables

140

Concord 4 Installation Manual

Sensor number

State

Trigger
n
umber

State

Trigger number

Senso
r 62

In alarm

190

Open

318

Sensor 63

In alarm

191

Open

319

Sensor 64

In alarm

192

Open

320

Sensor 65

In alarm

193

Open

321

Sensor 66

In alarm

194

Open

322

Sensor 67

In alarm

195

Open

323

Sensor 68

In alarm

196

Open

324

Sensor 69

In alarm

197

Open

32
5

Sensor 70

In alarm

198

Open

326

Sensor 71

In alarm

199

Open

327

Sensor 72

In alarm

200

Open

328

Sensor 73

In alarm

201

Open

329

Sensor 74

In alarm

202

Open

330

Sensor 75

In alarm

203

Open

331

Sensor 76

In alarm

204

Open

332

Sensor 77

In alarm

205

Open

333

Sensor 78

In alarm

206

Open

334

Sensor 79

In alarm

207

Open

335

Sensor 80

In alarm

208

Open

336

Sensor 81

In alarm

209

Open

337

Sensor 82

In alarm

210

Open

338

Sensor 83

In alarm

211

Open

339

Sensor 84

In alarm

212

Open

340

Sensor 85

In a
larm

213

Open

341

Sensor 86

In alarm

214

Open

342

Sensor 87

In alarm

215

Open

343

Sensor 88

In alarm

216

Open

344

Sensor 89

In alarm

217

Open

345

Sensor 90

In alarm

218

Open

346

Sensor 91

In alarm

219

Open

347

Sensor 92

In alarm

220

Open

348

Sensor

93

In alarm

221

Open

349

Sensor 94

In alarm

222

Open

350

Appendix B
:
Ref erence tables

Concord 4 Installation Manual

141

Sensor number

State

Trigger
n
umber

State

Trigger number

Sensor 95

In alarm

223

Open

351

Sensor 96

In alarm

224

Open

352


System feature event triggers

Table

29

below

describes the syst
em feature event triggers.

Table

29
: System feature event trigger numbers

Feature

State

Trigger number

Phone test

Initiated

225

AC failure

For 15 minutes

226

CPU low battery

Detected (excluding first minute after power
-
up)

227

A
uto phone test

Begun

228

Receiver failure

Detected

229

Back in service

Alarm (AC loss, battery drain, then AC
restore)

230

Phone failure

Detected

231

Buffer full

Detected

232

Two trip error

Detected

233

System tamper

Alarm (40 incorrect code entry ke
ystrokes)

237

Freeze

Alarm

238

No activity

Alarm

239

Fire panic

Alarm

240

Police panic

Alarm

241

Auxiliary panic

Alarm

242

Opening report

Occurred

243

Closing report

Occurred

244

Latchkey opening or
closing

Occurred

245

Duress

Alarm

246

Forced ar
med report

Occurred

247

Fire in partition

Alarm

248
Appendix B
:
Ref erence tables

142

Concord 4 Installation Manual

Feature

State

Trigger number

Recent closing report

Occurred

249

Sensor test

Entered

251


Appendix B
:
Ref erence tables

Concord 4 Installation Manual

143

Response characteristics

Table

30

below

describes the response characteri
stics.

Table

30
: Response characteristics

Response characteristics

Description

Momentary trip time

The point remains active for nn seconds (n is 1 to 12 seconds).
The default is 4 seconds.

3
-
minute trip time

The point remains active for 3 minutes.

Siren
-
time trip time

The point remains active while the sirens are sounding.

Sustained trip time

The point remains active for the duration of the event.

Siren pattern

The point activates and deactivates according
to the current
alarm type:

Auxiliary: fast on/off/on

Police: constant on

Fire: repeating

Trip delay

The point activates 30 seconds after the trigger event occurs.


Response numbers

Table

31

below

describes the response numbers.

Table

31
: Response numbers

Response number

Siren tracking

Trip delay

Response time

00

No

No

Momentary

01

No

No

3 minutes [5]

02

No

No

Siren time [2]

03

No

No

Sustained [3]

04

No

Yes [4]

M
omentary

05

No

Yes [4]

3 minutes [5]

06

No

Yes [4]

Siren time [2]

07

No

Yes [4]

Sustained [3]

08

Yes [1]

No

Momentary

09

Yes [1]

No

3 minutes [5]

10

Yes [1]

No

Siren time [2]
Appendix B
:
Ref
erence tables

144

Concord 4 Installation Manual

Response number

Siren tracking

Trip delay

Response time

11

Yes [1]

No

Sustained [3]

12

Yes [1]

Yes [4]

Momentary

13

Yes [1]

Yes
[4]

3 minutes [5]

14

Yes [1]

Yes [4]

Siren time [2]

15

Yes [1]

Yes [4]

Sustained [3]


[1] If an event does not trigger sirens, siren tracking response numbers activate without turning on
the output. If sirens are triggered by another event, the output p
ulses to match the siren. If the
siren cadence changes (from police to fire, for example), outputs set up for siren tracking change
to match the siren and all pulsing outputs pulse to one common cadence.

[2] If an event does not trigger sirens, siren time
response times activate outputs only if sirens are
active for another reason.

[3] If an alarm event does not necessarily require disarming (no activity, closing report, etc.),
outputs set up for a sustained response time remain activated until the next arm
ing level change.

[4] If an event occurs that activates an output set up for trip delay, the delay and output activation
can be canceled by trigger event restoral.

[5] Activated outputs set up for a 3
-
minute response time remain active for the entire three

minutes. To deactivate the output before the 3
-
minute time expires, you must enter program
mode or remove panel power. Activated outputs set up for a momentary or 3
-
minute response
time restart if the same trigger event occurs again.

Note:
The mechanical
lifetime of the relay may be exceeded if an output is set up
for a siren tracking response and a pulsing siren (auxiliary or fire) is active for
long periods. A SnapCard relay output’s lifetime expectancy is about 350 total
pulsing hours.

Note:
The trip de
lay is factory set for 30 seconds and cannot be changed.

Appendix B
:
Ref erence tables

Concord 4 Installation Manual

145

Specifications


Power requirements


Auxiliary power output

Class 2, 16.5 VAC, 40 VA, 60 Hz (part no. 600
-
1023 or 600
-
1024)

Batteries

Rechargeable 12 VDC, 4.5 or 5.0Ah Lead
-
Acid (part no. 60
-
681) O
R 12 VDC, 7Ah (part no. 60
-
680). The battery will last
24 hours with no AC and specified standby load

Radio frequency

319.5 MHz

Nominal RF range

1,000 ft (305 m) typical open air

Storage temperature

-

30 to 140°F (
-
34 to 60°C)

Operating temperature

32
to 120°F (0 to 49°C)

Relative humidity

85% maximum noncondensing

Dimensions

14 x 12 x 3 in. (356 x 305 x 76 mm)

147

Concord 4 Installation Manual


Uploaded