Interlogix TX+Door/Window Sensor - Install Guide Dated 09/2018

P
/N 466
-
5424

• REV
A •
20
SEPT
2018



©
2018 United Technologies Corporation. All rights reserved



TX+DWS

Door/Window Sensor Installation Instructions
PLEASE SEE REVERSE SIDE FOR IMPORTANT PRODUCT
WARNINGS AND DISCLAIMER INFORMATION.


Description


The TX
+DWS

Door/Window Sensor
is intended for installation on doors,
windows, and other objects that open and close. The sensor transmits signals
to the control panel when a magnet mounted near the sensor is moved away
from or closer to the sensor.


The TX
+DWS

features the TX+ Encrypt
ion protocol which provides encrypted
wireless communication to select Interlogix control panels. Please refer to your
panel’s installation instructions to see if it is TX+ Encrypted capable.


The TX+DWS also utilizes the standard ITI
-
319 protocol which i
s compatible
with all Interlogix control panels and receivers.

Figure

1
:
TX
+DWS




Enrollment

Into TX+ Encryption Supported Panels


To enroll the
TX
+DWS

as an encrypted sensor

into
a panel that supports the
TX+ Encryption protocol
,
follow these steps:

1)

Place the panel into program mode, then go to Learn Sensors menu.
Refer to your specific alarm panel manual for details on these
menus
.

2)

Once the Learn Sensors mode has been activated, r
emove the
battery pull tab to auto
-
enroll the device.

Then select the

appropriate
sensor group and number.
Refer to your specific alarm panel manual
for details on the different sensor groups.

3)

If the panel does not respond upon removing the battery pull tab,
exit
the Learn Sensors mode and then
remove

the
front sensor housi
ng

and transmitter

from the back housing by inserting a small flat head
screwdriver into the slot at the top of the sensor and pressing on the
tab.

Remove the batteries from the sensor.

4)

With the batteries removed, return back to the panel and activate the

Learn Sensors mode again. With Learn Sensors mode activated, re
-
insert the batteries (paying close attention to the battery polarity
indicators) to auto
-
enroll the device.

Note: Utilization of the TX+ Encrypted protocol is only compatible with
select Interlogix control panels. When enrolled into a panel that is TX+
Encrypted capable, the enrollment menu screen may indicate “TX+
Encrypted” to verify that the sensor is communi
cating to the panel via the
encrypted protocol. Please refer to your panel’s installation instructions
to verify that the panel supports TX+ Encrypted capability.


Enrollment
into

Non TX+ Encryption Supported Panels (ITI
-
319 Protocol)


To enroll the TX
+DWS

into a panel
utilizing the standard ITI
-
319 protocol,
follow these steps:

1)

First remove the battery pull tabs from the device.

2)

After the pull tabs have been removed, place

the panel into program
mode, then go to Learn Sensors menu. Refer to your specif
ic alarm
panel manual for details on these menus
.

3)

Once the Learn Sensors mode has been activated,
remove

the
front
sensor housing and transmitter

from the back housing by inserting a
small flat head screwdriver into the slot at the top of the sensor and
pressing on the tab. This will activate the tamper switch which will
auto
-
enroll the device.
Then select the appropriate sensor group and
number.
Refer to your specific alarm panel manual for details on the
different sensor groups.

4)

If the panel does not re
spond upon
tamp
ering the device,

replace
and then remove the cover again to tamper the sensor another time.
Repeat until the panel responds, and then continue to selecting the
appropriate sensor group and number.



Mounting

Included with this device is
double sided tape for the transmitter and magnet,
as well as screws if a more secure method of mounting is preferred. Choose a
suitable location for the sensor by following the procedure in the section
“
Sensor Testing
” ensuring desired signal strength is a
chieved. Note that it is
recommended the transmitter be installed on the stationary or non
-
moving part
of the installation (frame) and the magnet installed on the moving object (door).

Where possible, install sensors within 100 ft. (30 m) of the panel. Wh
ile a
transmitter may have an open
-
air range of 500 ft. (150 m) or more, the
environment at the installation site may have a significant effect on operational
range. Changing a sensor location may improve wireless communication.

For reliable bonding

with t
he provided double sided tape
, ensure the surface is
clean and dry. Apply the tape to the backside of the sensor, and then to the
desired location. Apply fi
rm pressure for several seconds.
When mounting with
double sided tape, ensure temperatures are above

50°F and will remain above
50°F for at least 24 hours to ensure proper bond. After 24 hours, the bond
will
hold at lower temperatures.

Sensor Testing


The sensor test verifies proper communication between the sensor and
the
panel/receiver.
The sensor should be tested prior to permanent installation, as
well as weekly.
To test the sensor, refer to the specific panel/receiver
documentation and do the following:

1)

Put the panel/receiver into sensor test mode

2)

Open the door/window the sensor is ins
talled on

–

the sensor will
then transmit a signal

3)

Listen for the siren beeps to determine the
appropriate response
.




P
/N 466
-
5424

• REV
A • 20
SEPT
2018



©
2018 United Technologies Corporation. All rights reserved


N
ote: When enrolled into a TX+ Encryption supported panel and
communicating via the TX+ Encryption protocol, the panel will beep up to

8

times for each transmission, indicating the total number of packets
received. It is recommende
d that at least 6
out of 8
packets are received
in the desired sensor location to ensure reliable communication to the
panel.

When enrolled into a panel and c
ommunicating via the standard ITI
-
319
protocol, the panel will beep up to 4 times for each transmission during
the sensor test mode, indicating the total number of packets received. It
is recommended that at least 3 out of 4 packets are received in the
des
ired sensor location to ensure reliable communication to the panel.

4)

Exit sensor test mode when proper c
ommunication between the
sensor
and pa
nel/receiver has been verified
.

Replacing the Batteries

The
TX+DWS

comes pre
-
installed with two

Energizer

CR
-
2032

Lithium
coin
-
cell batteries that provide up to 8

years of battery life under normal usage
conditions. When the
batteries are

low, a signal will be sent to the contr
ol
panel. To replace the batteries
, do the following:

1)

With the sensor mounted,
remove

the c
ase cover
from the back
housing by inserting a small flat head screwdriver into the slot at the
top of the sensor and pressing on the tab.

2)

Remove the existing batteries and re
-
install

new
Energizer CR
-
2032
batteries. When inserting the batteries
, pay close

attention to the
battery polarity indicators to ensure p
roper placement.

3)

Replace the case cover
and perform a sensor test to ensure proper
communication to the panel/receiver.


Figure 2
: Circuit Board Layout


TX+DWS

RF Frequency

319.
5

MHz

–

(Crystal
Based
)

Compatibility


(TX+ Encrypted)

Only Select
Interlogix 319.5 MHz control
panels/receivers

(refer to panel’s installation
instructions to verify compatibility)

Compatibility

(Standard ITI
-
319)

All Interlogix 319.5 MHz control
panels/receivers

Battery Type

2x
CR
-
2
032

(Panasonic)

Typical Battery Life

Up to 8

years at 68°F (20°
C)

Operating
Temperature Range

32° to 120°F (0° to 49
°C)

Relative Humidity

0
-
95
% non
-
condensing

Supervisory Interval

64 Minutes

Storage Temperature
Range

-
30
°

to 140°F (
-
34 to 60°C)



Dimensions

2
” x
1” x 0.5
”






FCC Compliance Statement


This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this

device must accept any interference received, including interference that may
cause undesired operation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the u
ser is encouraged to try to correct the interference by one or more of the following measures:


•


Reorient or relocate the receiving antenna.

•


Increase the separation between the equipment and receiver.

•


Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•


Consult the dealer or an experienced radio/TV technician for help.


Changes or modifications not expressly approved by UTC Fire and Security cou
ld void the user’s authority to operate the
equipment.


This device complies with Industry Canada
license
-
exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must acc
ept any interference, including
interference that may cause undesired operation of the device.


Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux
deux conditions suivantes: (1) cet appare
il ne doit pas provoquer d'interférences et (2) cet appareil doit accepter toute
interférence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil.


In accordance with FCC requirements of human exposure to radiofrequency fields, the rad
iating element shall be installed
such that a minimum separation distance of 20 cm is maintained from the general population.


Conformément aux exigences d'Industrie Canada en matière d'exposition humaine aux champs de radiofréquences,
l'élément rayonnant
doit être installé de telle sorte qu'une distance minimale de 20 cm soit maintenue par rapport à la
population générale.


FCC
:
2ABBZ
-
RF
-
CMDWS
-
UTC

IC:
11817A
-
RFCMDWSUTC


This Class B digital apparatus complies with Canadian ICES
-
3B.

Cet appareil numérique

de la classe B est conforme à la norme NMB
-
003 du Canada.


Contact information


For contact information, visit us online at www.interlogix.com.

For technical support, see
www.interlogix.com/support


Copyright


Copyright © 201
8

United Technologies Corporation. All rights reserved.


Trademarks


Interlogix is a registered trademark of United Technologies Corporation. Interlogix is part of UTC Climate, Controls & Securi
ty, a
unit of
United Technologies Corporation.


Product
Warnings and

Disclaimers



WARNING: CHOKING HAZARD
-

Small parts. Keep away from children.



ATTENTION: RISQUE D'ÉTOUFFEMENT
–

Petite pice. Garder eloigner des enfants.




THESE PRODUCTS ARE INTENDED FOR SALE TO, AND
INSTALLATION BY, AN EXPERIENCED SECURITY
PROFESSIONAL. UTC FIRE & SECURITY CANNOT PROVIDE ANY ASSURANCE THAT ANY PERSON OR ENTITY
BUYING ITS PRODUCTS, INCLUDING ANY “AUTHORIZED DEALER”, IS PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL SECURITY RELAT
ED PRODUCTS.


CES PRODUITS SONT DESTINÉS À ÊTRE VENDUS ET INSTALLÉS PAR UN PROFESSIONNEL DE SÉCURITÉ
EXPÉRIMENTÉ. UTC FIRE & SECURITY NE PEUT FOURNIR AUCUNE ASSURANCE QUE TOUTE PERSONNE OU
ENTITÉ QUI ACHETERA SES PRODUITS, Y COMPRIS TOUT «DÉTAILLANT AGRÉÉ»
, EST CORRECTEMENT
FORMÉE OU EXPÉRIMENTÉE À INSTALLER CORRECTEMENT LES PRODUITS LIÉS À LA SÉCURITÉ


For more information on warranty disclaimers and product safety information, please check
https://firesecurityproducts.com/policy/product
-
warning or scan th
e following code: