Leviton 47617-REB - Install Guide
Related Products
Related Categories
Document Transcript
47617
Technical Support: 800-824-3005
Customer Service: 800-722-2082
International: 425-486-2222
Fax: 425-483-5270
Web: www.leviton.com
Recessed
Entertainment Box
with Low Profle
Frame
DI-001-47617-00A
STEP 1:
WARNING: TO AVOID FIRE, SHOCK, OR
DEATH; TURN OFF POWER at circuit breaker or
fuse and test that power is off before wiring!
STEP 2A:
Mounting: New Construction – Stud Mounted
Installation (refer to Figures 1A and 1B):
1. Select the desired location for installation.
2. Ensure that you allow for wallboard material
thickness when mounting.
NOTE: The frame will allow the hiding of minor
imperfections or visible holes after mounting of
wallboard around Entertainment Box. The maximum
margin on the backside of the frame to cover
wallboard is approximately 3/8” (0.95 cm). Refer to
Figures 1A and 1B.
3. Using two (2) supplied wood screws, secure the
enclosure to the stud thru the two (2) mounting
slots (refer to Figure 1A).
4. After wallboard material is installed with cut-out
approximately 8.0” (20.3 cm) x 7.2” (18.3 cm)
in proper location, mount the low profile
frame (refer to Figure 1B) or the optional high
profile frame with cover (not included, refer to
Figure 4) to the Entertainment Box.
5. Install four (4) #8 screws into the four frame holes
to secure frame.
NOTE: The #6 screws with swing clips are used only
when installing in a retrofit construction.
STEP 2B:
Retrofit Construction – Wall Mounted
Installation (refer to Figures 2A and 2B):
1. Select the desired location for installation.
NOTE: This installation requires mounting the
Entertainment Box in between the studs with a
minimum clearance of 11.0” [27.9 cm (refer to note in
Figure 2A)]. If necessary, use a stud finder to locate
and mark studs that are behind surface of wall.
2. Using the front of the Entertainment Box as a
template, trace the enclosure outline with
a pencil on the wall surface (refer to Figure 2A).
Using a wallboard saw, cut the opening out of the
wallboard surface.
NOTE: Make sure that you leave enough space
for a device box which may be attached to the
Entertainment Box (refer to Figure 3A). If space
between studs is less than 14.0” (35.6 cm), the
Entertainment Box must be mounted offset from
center-line of studs.
3. Select the low profile frame or the optional
high profile frame with cover (not included, refer
to Figure 4) for the installation. Assemble frame to
Entertainment Box using the four (4) #6 screws
and by placing them into the four frame holes.
Attach the supplied swing clips to each screw prior
to mounting (refer to Figure 2B). DO NOT tighten
screws all the way down at this point.
NOTE: Ensure that the swing clips are placed on the
screws in the orientation as depicted in Figure 2B for
proper wallboard mounting.
4. Mount the Entertainment Box into the wall
surface opening ensuring that the swing clips
are positioned flat on box (refer to Figure
2B Detail). Secure to wallboard by tightening all
four screws. Make sure the swing clips catch the
wall material in all four locations (refer to Figure 2B).
STEP 3A:
Wiring Application:
Line Voltage Connections (refer to Figure 3A):
1. Use a standard Carlon 1-Gang Device Box
(reference: Carlon p/n B114R).
2. Select the desired location on Entertainment Box
and insert the device box from the inside. Tighten
the two mounting screws on the device box to
secure it to the Entertainment Box.
3. Route the electrical wires to the device box.
Install the desired line voltage device to support
your application needs.
NOTE: Refer to the individual device installation
instructions for complete wiring instructions.
4. Install the appropriate standard size wallplate onto
the device box and device, if necessary.
NOTE: If using a Decora
®
style wallplate, ensure that
1/4” (0.64 cm) mounting screws are used to secure
wallplate.
5. Repeat steps 1 thru 4 to install additional devices
in other locations. Use the Snap-on Cover Plate
provided for unused openings.
STEP 3B:
Low Voltage Connections (refer to Figure 3B):
1. Use a 1-Gang Low-Voltage Bracket (reference:
Levion p/n C0224 or Carlon p/n B100R) for low-
voltage devices.
2. Select the desired location on Entertainment Box
and insert the Low-Voltage Bracket. Tighten the
two mounting screws on the Low-Voltage Bracket
to secure it to the enclosure.
3. Route the low-voltage cables/wires through the
bracket. Install the desired low-voltage device(s)
required to support your application needs.
NOTE: Refer to the individual device installation
instructions for complete wiring instructions.
4. Install the appropriate standard size wallplate onto
Low-Voltage Bracket, if necessary.
NOTE: If using a Decora
®
style wallplate, ensure that
1/4” (0.64 cm) mounting screws are used to secure
wallplate.
5. Repeat steps 1 thru 4 to install additional devices
in other locations. Use the Snap-on Cover Plate
provided for unused openings.
STEP 3C:
Component To Component Connections
(refer to Figures 3C and 3D):
1. To route low-voltage connections from component
to component, use the existing Snap-on Cover Plate.
2. Using a swedge knife, cut the knock-out from the
Snap-on Cover Plate (refer to Figure 3C).
NOTE: The knock-out size is 1.25” (3.2 cm) in diameter.
3. Gently pull low-voltage wires thru hole in Snap-on
Cover Plate. Snap the Cover Plate into the opening
and connect wires to appropriate application.
4. Repeat steps 1 thru 4 to run additional low-voltage
connections in other locations. Use the Snap-on
Cover Plate provided for unused openings.
Parts Included:
1) Recessed Entertainment Box (1)
2) Low Profle Frame (1)
3) Cover Plate (1)
4) #10 Wood Screws (2)
5) #6 Screws (4)
6) Swing Clip (4)
7) #8 Screws (4)
Tools needed to install your
Entertainment Box:
1) Slotted/Phillips Screwdriver
2) Electrical Tape
3) Wallboard Saw
4) Pencil
5) Cutters
6) Ruler
7) Swedge Knife
1
2
5
7
4
6
4
3
2222 - 222nd Street SE
Bothell, WA 98021, USA
Phone: 425-486-2222
Fax: 425-483-5270
DI-001-47617-00A
WARNINGS AND CAUTIONS:
• To be installed and/or used in accordance with appropriate electrical codes
and regulations.
• If you are unsure about any part of these instructions, consult a qualifed
electrician.
IMPORTANT INSTRUCTIONS:
1. Read and understand all instructions. Follow all warnings and instructions
marked on the product.
2. Do not use this product near water—e.g., near a tub, wash basin, kitchen
sink or laundry tub, in a wet base ment, or near a swimming pool.
3. Never push objects of any kind into this product through openings, as they
may touch dangerous voltages.
4. SAVE THESE INSTRUCTIONS.
SAFETY INFORMATION:
1. Never install communications wiring or components during a lightning storm.
2. Never install communications components in wet locations unless the
components are designed specifcally for use in wet locations.
3. Never touch uninsulated wires or terminals unless the wiring has been
disconnected at the network interface.
4. Use caution when installing or modifying communications wiring or
components.
5. To prevent the possibilty of electrical shock, each opening must have a
device or snap-on cover plate installed.
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the
purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option, if within such five year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton
Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This
warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or
instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty,
including merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost
sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
Screws (2)
Stud
Mounting
Slots
Entertainment
Box
#8 Screws (4)
Approx.
3/8" (0.95)
margin on back
of frame to
cover wallboard
Low Profile Frame
Wallboard
Wallboard
Trace along back front
edge of enclosure for template
[approx. 8.0" (20.3 cm) x 7.2" (18.0 cm)].
NOTE: If there is less than
14.0" (35.6 cm) clearance
between studs, mount box offset
from center-line of studs.
7.2
(18.0
cm)
8.0"
(20.3 cm)
11.0" (28.0 cm)
minimum
between studs
Wallboard
#6 Screws (4)
Swing Clip (4)
(note orientation)
Low Profile Frame
See
Detail
Detail
Device Box
Line Voltage
Wires To
Device
Low-Voltage
Bracket
Low-Voltage
Wires To
Device
Remove knockout
on back side of
Cover Plate
Plate
Cover
Optional High Profle Frame with Cover
Cat. No. 47617-HPC
1A
1B 2A 2B
3A 3B 3C 4
- Uploaded