PROOUTMV Installation and Setup Guide - 8/22

PRO
OUT
MV

Outdoor

Motion Viewer

Installation and Setup Guide

The
PROOUTMV

is a battery-
powered
, wireless outdoor motion
detector with a built
-in video camera is intended for
use with
ProSeries Control Panels. The detector is powered by three
C123
A lithiu
m batteries that provide up to 4 years of battery life
(typical use).

The de
tector can be mounted directly on a wall or with a
n
optional
mounting bracket.

NOTE
:
Installation shall be done in accordance with
the
National Electrical Code, NFPA 70
.


FEATUR
E
S

•

No wiring or remote power required. Fully portable battery powered camera allows for
flexibility in selecting locations

•

Provides video stream and live video viewing functionality
•

The module features an advance triggering algorithm to minimize the possibi
lity of false alarm activations.

•

AES Encrypted Wireless technology provides optimum sign
al integrity and security

•

CMOS camera sensor with a wide angle 90° lens
(horizontal field of view)

•

Night vision (up to
16
feet
,
5 meter
s) with one white LED

•

Fresnel len
s motion detection: 3
9.73 ft (
12m
), and
90° detection pattern

•

Camera sends color video

ENROLL
MENT

You m
ust enroll the detector in the Control Panel.

Enrollment and RF testing should be done while the detector
is in its
intended mounting location to ensu
re good communication between the
Con
trol Panel and the device.

NOTE
:
For detailed programming instructions refer to the Installation
Instructions for the Control Panel with which this device is used.

1.
Remove the set screw
[A]
that secures the rear
housin
g
[B]
to the
front housing

[C]
. Remove the
rear
housing.

2.
Remove the screw
[D]
that secures the battery cover
[E]
to
the
front
housing

[C]
. Re
move the battery cover.

3.
When prompted,
perform one of the following:

•
Carefully remove (and discard responsibly) the battery tab
[F]
.
•
Insert the b
atteries
[G]
.
•
If powered, open and close the
back housing again.

4.
The
LED on the front flashes rapidly at power
up.

5.
Reassemble the
detector
.

NOTE
: After enrolled in a system, the device cannot be used with another Control P
anel until it is removed from the current panel. See the
Control Panel instructions for details.

MOUNTING CONSIDERATIONS

The detector can be

mounted d
irectly on a wall
or with t
he PROOUTMV
-
MB mounting bracket (available

separately).


All programming

and
RF testing should be done while the detector is in its intended mounting location to ensure good communication between the Co
ntrol Panel
and t
he detector
.
NOTE
:
After
enrolling, v
erify adequate signal strength by conducting a sensor test with the device installed in its intended mounting location
(see the Control Panel instructions).
Adjust the device mounting location and orientation as necess
ary to achie
ve
maximum signal
strengt
h.
•

Use proper tools and hardware.

•

Mou
nt the
camera
at heights per
the
"PIR Fi
eld of View and Mou
nting Height Considerations"
section.

•

Do not
mount
too
close or
aim
at an air con
ditioner or other
heat source
.
•

Do not aim the
det
ector
at moving objects
such as
auto
mobil
e traffic
or outdoor fans
.
•

Do n
ot
pai
nt or cover the
detection or
camera lens.

•

Do not aim the detector directly at
a close wall (within
16 ft
/5 m
) to minimize
any

excessive light reflections
and en
hance
the camera
viewing area.

MOUNTING

The detector can
be mounted directly on a wall or wit
h a
PROOUTMV-
MB
mounting bracket
(available separately)
.
Direct Wall
Mounti
ng

To mount the detector
directly
to a wall, perform the following
:

1.
Remove the water
protection
cover

[A]
from the detector
.
2.
Remove the set screw
[B]
that secures the detector f
ront housing
[C]

to the rear
housing
[D]
and carefully separate the housings.

3.
Secure the rear housing to the wall in the desired location with
screws
[E]
.
NOTE
:
The de
tector
can be mounted flat
or
angled on a wall
:
•

W

= Wall Mounting Holes
•

C
= Corner Mounti
ng Holes
4.
Reassemble the detector front housing
[C]
to the rear housing
[D]

an
d secure with set screw
[
B]
.

5.
Install the water protection cover
[A]
on the detector.



Direct Wall
Mounting
(Contin
ued
)


Mounting with M
ounting Bracket

To mount the detector to a wall with the
mountin
g bracket, perform the following:


1.
Mount
the
mounting
bracket
to the wall as follows:

a. Insert shaft screw
[A1]
through the back of the wall mounting plate
[A2]
and
thread
the
bracket extension shaft
[A3]
onto the
shaft s
crew
[A1]
until secure.

b. Secure the m
ounting plate to the wall at
the desired location
with four screws
[A 4]
.
Note:
Mounting plate must be mounted on a stud, solid wall, or with a robust wall anchor.

c. Slide the protective
cover
[A 5]
over the wall mounting plate
[A1
]
and snap to secure in place.

2.
Mount the d
etector to the m
ounting
bracket as f
ollows:

a. Remove the water protection cover
[B
1
]
from the detector.

b. Remove the set screw
[B2
]
that secures the detector front housing
[B
3
]
to the rear housing
[B
4
]
and carefully separate the
housings.

c. Secure
the junction
ball

[A
6
]
to the rear housing with t
hree screws
[A
7
]
.
d. Reassemble the detector front housing
[B
3
]
to the rear housing
[B4]
and secure with set screw
[B
2
]
.
e.
Slide the extension
shaft sleeve
[A8]
completely
over the extension shaft
[A3]
and
insert
the junction ball
[A6]
into the
opening of the s
leeve
[A8]
.
f.
When both the junction ball
[A6]

and the extension shaft
[A3]
are fully seated in the extension shaft sleeve
[A5]
, tighten the
bracket knob
[A9]
snugly
to se
cure both in place.
g. Rotate and angle
the detector as necessary to view the desired det
ection
area
(PIR field of view)
and tighten the bracket knob
[A 9]
to secure the adjusted setting.

NOTE
:
See
the
PIR F
IELD OF VIEW

section f
or
adjustment
details.

h. Insert and tighten the stop screw
[A10]
to se
cure in place.

i. Install the water protection cov
er
[B1
]
on the detector.
NOTE:
See the
Installation of the Full or Half Window (PROOUTM
V-CT) Housing section for
instructions.


INSTA
LLING THE FULL OR HALF WINDOW (PROOUT
MV
-
CT) HOUSING

OR
prooutmv-016-V0
FRONT HOUSING HALF WINDOW
(PROOUTM
V-CT)
FRONT HOUSING FUL
L WINDOW
1
2

PIR FIELD OF VI
EW

AND MO
UNTING H
EIGHT

C
ONSIDERATIONS


NOTE:
0° Mounting is also suitable for
direct wall mounting with no bracket
and the preferred mounting height is between
6.8 an
d 8.8 feet
(2.1
and 2.7
me
ter
s).




Mounting Angle
/ Detection Distance


0°
5°
10°

15°
20°

30°

Mounting
Height

ft
m
ft
m
ft
m
ft
m
ft
m
ft
m
ft
m
6.56
2.0
34.
4
10.4
24.6
7.5
19.6
6.0
16.4
5.0
13.1
4.0
8.2
2.5
6.99
2.13
37.
7
11.4
26.2
8.0
21.3
6.5
16.4
5.0
14.7
4.5
8.2
2.5
7.55
2.3
39.
3
12
29.5
9.0
21.3
6.5
18.0
5.5
14.7
4.5
9.8
3.0
7.87
2.4
41.0
12.4
31.1
9.5
21.3
6.5
18.0
5.5
16.4
5.0
11.4
3.5
9.02
2.75
44.2
13.4
32.8
10.0

24.6
7.5
21.3
6.5
18.0
5.5
14.7
4.5
9.84
3.0
--
--
36.0
11.0

31.1
9.5
22.9
7.0
19.6
6.0
14.7
4.5
10.99
3.35
--
--
39.3
12.0

32.8
10.0

24.6
7.5
21.3

6.5
14.7
4.5
12.01
3.66
--
--
--
--
34.4
10.5

26.2
8.0
22.9
7.0
16.4
5.0
13.12
4.0
--
--
--
--
39.3
12.0

27.8
8.5
24.6
7.5
16.4
5.0


DETECTION PATTERNS

(Mounted at
7.5
ft
(2.
3
m)

Directly on the Wall
)

Top View

Side View



Z
ones

A

18

L
o
we
r

B

46

Interm
ediate

C

36

Long




WALK TEST

After enrolling, you can use the Control Panel
to perform a
10
-minute
Walk Test m
ode for the sensor.
With the detector
in its intended
mounting location, adjust the location and orientation as necessar
y.
Note:
For detailed instructions on performing the Walk Test, refer to
the Installation Instruction
s for the Cont
rol Panel.

1. Walk through the detection area
[A]
and observe the LED
[B]
comes ON.

2.
After 10 minutes, the detector automatically exits th
e Test
mod
e,
disables the LED, and enters a normal operation mode.

To restart a 10
-minute Walk Test period,
activate the
Walk Test mode
with t
he Control Panel (see the Control Pan
el instructions).

The user can manually stop the Walk Test at any time.

NOTE
: Syste
m mu
st be
disarmed
to enter Test Mode and can only
be armed again after exiting the Walk Test mode.


BATTERY REPL
ACEMENT

The detector
must be disassembled to access the battery
compartment. Follow the instructions in the
ENROLLMENT
section
to acce
ss the
bat
tery compartment.

The detector is powered by three Lithium batteries. To maximize
battery efficie
ncy, it is imp
ortant to
remove all
of the old batteries,
wait approximat
ely 10 seconds, and then install new batteries.

NOTE
:
See the
SPECIFICATIONS

section
for recommended
replacement batteries. To ensure good product batter
y life,
do not mix old and new
batteries, bat
tery types, or
manufacturers.

BATTERY
CAUTION
:

Risk of f
ire, explosion, and burns.
Do not recharge, disassemble,
heat above
212
°F (10
0° C
) or incinerate. Dispose of used batteries
properly. Keep away from children.

NOTE
:
C
onstant exposure t
o high or low temperature or high
humidity may reduce battery life.


Specificat
ions


Electrical

Ba
ttery
.........................................................................................................................................................................................................................
Three (3)
3V Lithium batteries

Battery P
art Nu
mb
er ...........................................................................................................................................................................
DURACEL
L DL123A; PANASONIC
CR
-123A

Nominal voltage
.....................................................................................................................................................................................................................................................
3 V

Low battery
threshold
..........................................................................................................................................................................................................................................
2.7 V
Estimated bat
tery life
.............................................................................................................................................................................................................................
Up
to
4 yea
rs
Current co
nsumption
...............................................................................................................................................................................
Standby (1h average)
85
μA
/
Max 3
50 mA


Radio Properties

Wiselink
® technology

Radi
o type
.............................................................................................................................................................................................................
Spread spectrum RF bidirectional

Ope
rat
ing fre
qu
ency
.........................................................................................................................................................................................................
915 MHz (USA
& Canada)

Transmission security
........................................................................................................................................................................................................
AES
algorithm
encryption

Supervisi
on ........................................................................................................................................................................................................................................
Radio, batteries

Radio antenna
..............................................................................................................................................................................................................................................
Integrated
Specifi
cations
(Continue
d)

Video P
roperties

Camera

Angle
(HFOV)
............................................................................................................................................................................................................................................................
90°

Sensor type
.........................................................................................................................................................................................................................................................
CMOS

Spectr
al Resolution
................................................................................................................................................................................................................................................
Color

Night
vision
...................................................................................................................................................................................................................................
Automatic
Whi
te
LED

Vid
eo
distance
.................................................................................................................................................................................................................................................
23ft
(7m
)
Video format
.........................................................................................................................................................................................................................................................
H.264

Fra
me rate
..............................................................................................................................................................................................................................................................
10fps

Spatial r
esolution
...............................................................................................................................................................................................................................
QV
GA (320
x240)

Video File Size
...........................................................................................................................................................................................................................................
Up
to 230 kB


Detection Properties

Infrared de
tection specific
ations

Tec
hnology
............................................................................................................................................................................................................................................
Passive
-inf rared

Ty
pe
..............................................................................................................................................................................................................................................
Dual element sensor

Lens
....................................................................................................................................................................................................................................................................
Fresnel

Detection angle
........................................................................................................................................................................................................................................................
90°

Detection range
.................................................................................................................................................................................................................................
Up to 39.3
ft (
12m)
Initial
ization tim
e .........................................................................................................................................................................................................................................
90 seconds

Recovery t
ime
....................................................................................................................................................................................................................................
90
- 180
sec
onds


Physical
properties

Dimensions
...................................................................................................................................................................................................
5.04
x 2.2
8
x 2.1
7 in (12
8
x
58
x
55 mm)

With Sleeve:
5.20
x 2.4
4

x 2.7
6 in (132
x
62
x 70
mm)

With
Sleeve and Bracket:
5.20

x
2.44
x
5.0
8 in (132
x
62
x
12
9 mm)

Weight
(includes
3 batteries
) ..................................................................................................................................................................
No Brack
et and
No Sleeve:
7.37
oz. (209g
);

With
Sleev
e and
No Brac
ket:
8.64
oz. (
245
g);

With Sl
eeve and Bracket: 11.89
oz. (
337
g)
Tamper
......................................................................................................................................................................................................................................................
Cover tamper


Installation / Mounting

Mounting height
.....................................................................................................................................................................................................................................
7ft . 6
in. (2.3m)
Mounting Brack
et ............................................................................................................................................................................................PROOUTMV
-MV
(Available Sep
aratel
y)

Environmental

Opera
ting temp
erature
.......................................................................................................................................................................................................
-20° to 140°F (
-30°
to +
60°C)

Physical
Protec
tion
................................................................................................................................................................................................................................................
IP65


Standards and Approval
s
915MHz FHS
S – PRO
OUT
MV
Conforms to UL STD 639

Certified to ULC STD S306

Certi
fications

USA FCC Par
t 15C (FCC47 C
FR Pa
rt 15)

CANA
DA
IC (RSS
-247, Issue 1)


FCC
ID:
...............................................................................................................................................................................................................................
CFS
8DLPROINDMV

IC:
.............................................................................................................................................................................................................................................
573F
-PROINDMV

HVIN:
................................................................................................................................................................................................................................................
PRO
OUT
MV



FE
DERAL COMMUNICATIONS COMMISSION
& INDUSTRY CANA
DA
STATEMENTS

The user shall not make any changes or mod
ifications to the equipment unless
authorized by
the I
nstallation
Instructions or User's Manual. Unauthorized changes or modifications could void th
e user's
authority to operate the equipment
.
FCC CLASS
B STATEMENT

This equipment has been tested to FCC
requirements and
has been found accept
able for use.
The F
CC requires
the following statement for
your information:

This equipment generates and uses rad
io frequ
ency energy and if not installed and used prope
rly, that is, in strict accordance with the manuf
act
urer's
instruc
tions, may cause inte
rference to ra
dio and
television
reception. It has been type tested
and found to comply with the limits
for a Cla
ss
B computing device in accordance with th
e specifi
cat
ions in Par
t 15 of FCC Rules, which are designed t
o
provide
reasonable protection agains
t such interference
in a resident
ial installation. However,
there is
no guarantee that interference wil
l not occur
in a particular installation. If this equipment does
ca use
inter
ference to radio or television reception,
which c
an be determined by turning the equipment
off a
nd on, the us
er is encouraged to try to correct t
he interference by one or more of t
he followi
ng
me
asur
es:

•
If using an indoor antenna, have a qualit
y outdoor
antenna installed.

•
Reorient the recei
vin
g antenna unti
l interference is reduced or eliminated.

•
Move the
radio or television receiver
away fro
m the receiver/control.

•
Move the
antenna lea
ds away
from any wire runs to the receiver
/control.

•
Plug the receiver/control into a different outlet
so
that it
and the radio or television
receiver are on di
fferent branc
h circuits.

•
Consult the d
ealer or
an experienced radio/TV technician
for help.

INDUS
TRY
CANADA CLASS B STATEMENT

This Clas
s B digit
al apparatus c
omplies with Canadian ICES
-003.

Cet appare
il numé
rique de la classe B est con
forme à la nor
me NM
B-003 du Canad
a.
FCC / IC STATEMENT

This
device c
omplies with Part 15 of the FCC Rul
es, and Ind
ustry Ca
nada’s license
-
exempt RSSs. Operat
ion is su
bje
ct to the f
ollowing two conditions
: (1) This devic
e m
ay not cause h
armful interference
(2) This device
must
accept any
interference received, including interference that may cause undesired operation.



Cet appareil est conforme à la partie 15 des r
ègles d
e la FCC et

exempt de licence RSS d’Industrie Cana
da.
Son fonctionn
ement est soumis aux
conditions sui
vantes: (1) Cet app
areil ne doit pas causer
d’interfér
ences
nuisibles. (2) Cet appareil d
oit accept
er toute
interférence
reçue y compris les i
nterférences
causant une
réception
indésirable.


RF Exposure

Warn
ing
- The antenna(s) used for this device must be
inst
alled to pr
ovide
a separation distance of at leas
t 7.8 inches (20 cm) from all persons and mus
t not be
co-located or operating in conjunc
tion
with
any
other ant
enna or transmitter except in accordanc
e with FCC
and IS
ED multi-
transmitter
product procedures
.

Mise en G
arde
Exposition aux Frequence
s Radio:
La/les antenne(s) utilisée(s) pour cet émette
ur doi
t/d oivent
être
installée(s)
à une dis
tance de sép
aration d'au moins 20 cm (7,8 pouces) de toute per
son
ne et n
e
pas être située(s) ni fonc
tionner parall
èlement à tout aut
re transmetteur ou antenne,

excepté
en conformité avec les procédures de produit m
ulti tra
nsmetteur FCC et ISED
s.


Responsi
ble Party
/ Issuer of S
upplier’s Declaration of Conformity: Ademc
o Inc.,
a subs
idiary of Resideo Tec
hnologies, Inc
., 2 Corporate C
ent
er Drive., Melville, NY 11
747, Ph: 516
-577
-2000




The product should

not be di
s
po
se
d

of

with other household waste. Check

for the
nea
r
e
st author
ized collection centers or authorized r
ecyclers.
The cor
rect

disposal of end
-of-life equipm
ent w
ill help pr
event potential negative cons
equences
for the environment and human healt
h.
Any at
tem
pt to
reverse
-engineer this device by decoding pr
opr
ietary prot
ocols, de-
compiling firmware, or any si
milar actions is strictly prohibited.

Device physical pr
otection
- de
vic
e shall be installed in
area that
is not publicly accessible
.
Instal
lation phy
s
ic
al

pro
tection
-

sy
stem shall be installe
d in area

no
t

publicly
accessible, this includes wiring protec
tion as we
ll
.






www.resideo.com

Resideo Technologies, Inc

2 Corporate Center Drive, Suite 100
P.O. Box 9040
, Melville, N
Y 11747

© 2023
Resideo Technologies, Inc. All rights reserved.

The Honeyw
ell Home trademark is used u
nder license from Honeywell Interna
tional, Inc.

This product is manufactured by Resideo Technologies, Inc. and its affiliates.

ÊR800
-26710B
fŠ

R800
-
26710
B

8
/22


Rev
B