Qolsys IQ RECESSED S-Line Quick Installation Guide

STEP
1
IQ RECESSED DW QUICK INSTALL GUIDE
CHOOSE
INSTALLATION
LOCATION
SPECIFICATIONS
Sensor: 2.25”D x .75”H
Wireless signal range: 600ft (200M), open air.
Code outputs: tamper, tamper restore, alarm, alarm
restore, low
battery.
Transmitter frequency: 319.5 MHz
Unique code ID
Supervisory keep-alive interval: 70 minutes.
RF Peak field strength: typical 36000 uV/m at 3m
Operating Temperature: -10C~50C
Relative Humidity: 5-95% Non-Condensing
Storage Temperature: -40-80C
Replace battery with exact replacement every 5 years
with
3V CR2 (x1).
Improper installation may lead to
door damage. Please follow
instructions outlined in this guide.
OPTION 1:

SENSOR AT TOP
OF DOOR
OPTION 2
:
SENSOR ON SIDE
OF DOOR
OPTION 1:

MAGNET AT
TOP OF DOOR
OPTION 2:

MAGNET AT
SIDE OF DOOR
IMPORTANT NOTE:
BASED ON DOOR TYPE,
YOU MAY CHOOSE TO
INSTALL SENSOR IN
THE FRAME INSTEAD
OF THE DOOR
MAGNET SIZE
2.25”
.75”
.63
.75”
This is a quick guide for experienced installers only. Refer to http://dealers.qolsys.com (login required)
STEP
2
LEARN
INTO
PANEL
STEP
3
DRILL
SENSOR
HOLE
2.5” DEEP
USE 3/4” BIT
STEP
4
INSTALL
SENSOR
STEP
5
DRILL
MAGNET
HOLE
IMPORTANT:
BE SURE
MAGNET WILL
ALIGN WITH
SENSOR WHEN
DOOR CLOSES
STEP
6
INSTALL
MAGNET
IMPORTANT:
THE SENSOR WAS
DESIGNED TO FIT
SNUGLY IN A 3/4”
HOLE. PLEASE
TAKE CARE WHEN
DRILLING TO ENSURE
PROPER FIT
.75” DEEP
USE 3/4” BIT
2.25”
.75”
.63
.75”
Document#: IQRDW-SQG-02-17

Revision#: 2/24/17

Issue Date: FEB 2017

Qolsys Product #: QS113
4-840
Place your panel in
“autolearn" mode
Customize name and settings
as desired and and touch “ADD”
ADD
Open and close the connection
to “tamper” the device
Pull battery tab to place
device in “learn” mode
TechSupport@Qolsys.com
Qolsys Inc. proprietary.
Reproduction without permission is not permitted.
FCC ID: 2ABBZ-RF-
RDWS-AAA
IC: 11817A-RF
RDWS
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter toute
interférence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil.
CONTACT TECH SUPPOR
T
GOT QUESTIONS?