Qolsys IQ WIFI - Mesh WIFI Device - Quick Start Guide Dated 06/15/2021

The IQ WiFi is a mesh capable router that
covers every corner of every room with safe,
seamless WiFi.

Features
:
•
WiFi mesh prioritizes ethernet backhaul
(wired connection) then shared wireless
backhaul (if wired connection isn’t available)

•
Stand alone or parallel con
fi
guration
supporte
d
•
Web interface or IQ Panel con
fi
gurable

•
WiFi version 5

•
Supports Dual-band 2.4G/5
G
•
Supports 7 additional Agents (1 Controller
)
IQ WIFI QUICK INSTALL GUIDE
SKU: QW8200-84
0
Dimensions: 150mm x 89 mm x 57.2 m
m
Weight: 172
g
Usage: For Indoor use only

Compliance: FC
C
Process and Memory: SSoC: MT7621DA
(MIPS1004Kc dual-core 880MHz, SPI NOR Flash
64MB)


Memory: 128MB DDR3 embedded

Operating Temperature: 0°C - 40°C (32°F - 104°F)

Relative Humidity: 10% - 90% RH (non-condensing
)
Operating Distance: Up to 130f
t
Frequency Type:

Wireless IEEE 802.11 b/g/n 2.4GH
z
IEEE 802.11 a/n/ac 5GH
z
Wired Type
:
LAN and WAN Gigabit Ethernet Port
s
LED Indicator: 2 color LED (Green and Red)

Power Supply:

Input: 100-240VAC, 50-60Hz, 0.3A Ma
x
Output: 12 VDC, 1A
SPECIFICATIONS
FEATURES & OVERVIEW
This is a quick guide for experienced installers only. Refer to technical downloads at http://dealers.qolsys.com (login required) CONNECT THE IQ WIFI
STE
P
3
POWER UP THE IQ WIFI
STE
P
1
This is a quick guide for experienced installers only. Refer to http://dealers.qolsys.com (login required)
STE
P
2
CONNECT TO THE MODEM OR EXISTING NETWORK
1.
Plug the barrel jack end of
the power supply into the
“DC-IN” por
t
2.
Connect the provided
ethernet cable into the
“WAN” port
Connect the opposite end of the provided
ethernet cable into the “ETHERNET” port on
the modem*.
Plug in your power
supply to the wall
outlet
.
* Note: IQWIFI may
take up to 5 minutes to
power up before
proceeding to the next
step.
*Note: for parallel installs plug the
ethernet cable into an available
port on the customer’s existing
router (see additional
considerations)
STE
P
4
ADD ALL AGENTS
1.
Power up an additional IQ WiFi (see step 3
)
2.
From the controller brie
fl
y touch the WPS button
to activate pairing mode.

3.
From the agent brie
fl
y touch the WPS button to
pai
r
4.
Allow 3-4 minutes for the agent to pair and auto
update.

Note: LED behavior; LED will slowly
fl
ash indicating
pairing WPS mode has been enabled. If followed by
a red
fl
ash, pairing was unsuccessful.
1
2
2
3
3 PAIR CONTROLLER TO IQ PANEL
STE
P
6
RENAME YOUR NETWORK (SSID)
STE
P
5
This is a quick guide for experienced installers only. Refer to http://dealers.qolsys.com (login required)
1.
Open settings tray from IQ
Panel > Settings >
Advance Settings > type in
valid code > touch
Installation > Devices >
WiFi devices > IQ WiFi
ico
n
2.
Touch the down arrows to
make edits to the Network
Name (SSID’s)
STE
P
7
CREATE UNIQUE SSID AND PASSWORD
2
1.
Enter a unique
network nam
e
2.
Enter a unique
security ke
y
3.
Touch Save
1
2
1.
Open settings tray,
touch Settings >
Advanced settings >
type valid dealer or
install code > WiFi.
1
3
2
2.
Look for the
broadcasting SSID
or network name
and touch it. SSID
will be IQ WiFi
(+Last 6 of MAC)
3
3.
Enter password
printed on sticker
or bottom of router.
Password: (S/N)

4.
Touch connect Adding Additional Agents
:
-
Add up to 7 agents per Controller for a total of 8 IQ WiFi units.

-
Ethernet backhaul is supported and will default to wired
connectivity so long as an ethernet cable has been connected
properly.
Document#: IQWIFI0615202
1
Revision#: 6/15/2
1
Issue Date: JUNE 202
1
Qolsys Product #: QW8200-840
intrusion-support@tycoint.com
Johnson Controls proprietary.

Reproduction without permission is not permitted.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation. Changes or modi
fi
cations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter toute
interférence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil.
CONTACT TECH SUPPORT
QUESTIONS?
TROUBLESHOOTING
ADDITIONAL CONSIDERATIONS
Factory Default
:
-
Press and hold the physical
reset button for about 15-20
seconds or until the Power LED
begins to
fl
ash. During a reset
the power LED will
fl
ash quickly,
slow to a stop, reboot and then
slowly pulse until it remains solid
GREEN.
You can set up the IQ WiFi in either of these ways:
As the only wireless network on the premises:
In parallel with an existing wireless network:
Great for
:
-Improving connectivity for ALL WiFi devices
on the network
.
-Offering support for the entire network.
Great for
:
-Keeping the security and smart-home devices
private/hidden from the rest of the WiFi connected
devices on the network
.
-Making online/remote support easier as only
known/authorized devices should be connected
.
-Ensuring better connectivity for dealer supported
devices.