Resideo IPCAM-WOC2 - Quick Install Guide - Dated 03/2021 Rev. A

Google Play and the Google Play logo are trademarks of Google Inc.


IPCAM
-
WOC
2


HD Wi
-Fi Outdoor Video Camera

Quick Installation Guide

IPCAM
-WOC
2 is a 1080p, full HD Wi
-Fi ® video camera intended for outdoor
use with Resideo
Total Connect® 2.0.

•
Camera setup requires a Total Connect® 2.0 account and the Total Connect 2.0 mobile app.
Video Services
must be enabled in AlarmNet 360™.

•
Camera operation requires minimum available bandwidth of 2.1 Mbps.

Package Contents

A. Camera

B. Sun shield

C. Power
cable extension [8’ cable]

D. Power adapter with 7
’ cable

E. Pig
-tail power cable

F. Screws and Allen wrench

G. Antenna


a. Bluetooth antenna

b. Not
used

c. Reset switch

d. Power

Planning
Configuration
and

Installation


See the other side of this sheet
for more about mounting at the installation site

•
The
camera should be situated
within
200
feet
(61 m)
of a power outlet and within the verified range of its W
i-Fi® connection. DO NOT mount the camera
within 1 foot
(0.3 m) of
any other wireless device. Depending on the specifics of your installation,
a range extender
may be needed to ensure adequate Wi
-Fi
signal strength.
•
Pre
-installation:
It is s
trongly recommended that camera
configuration
be done as close as
possible to
the
Wi
-Fi router
with
which the camera will be linked
.
After setup,
use
a third
-party
app to check signal strength at the installation
site
before mounting
(over for more information on signal strength.)

•
The power adapter must be connected to a
non-
switchable power outlet.

•
Direct sunlight on the camera lens / image sensor may affect picture
quality
. When placing the camera, consider how the lighting can vary with time of day
and other conditions. The included sun shield can
be attached to the camera
to help minimize problems with sun glare.

IMPORTANT
: Use
onl
y ONE
of the included power extension cables.
This
cable
add
s
8 feet
(2.44
m) to the supplied power adapter for a total of
15 feet
(4.5 m).
Alternately
, you may use the pig-
tail power cable to extend the power adapter cable with a maximum of
200 feet
(61 m) of
18
AWG
wire.

If the included extension cable is
not used
, you may cut
and splice (observing good workmanship) the power transformer cable.


Ensure proper polarity if the pig
-tail power cable is used. The pig
-tail’s black (negative) wire must be connected to the negative (white
dashed) wire on the power adapter.


Wi
-Fi Configuration and Camera Registration



Download the Total Connect® 2.0 app
from

the App Store or
on
Google Play.


(Look for the red
Total Connect
2.0
logo.
)
Note
: Significant differences between the
iOS
and Android
version
s of the app
are
noted in the
se instructions
.
For best results, configure only one camera at a time
.
Check
these setting
s when you turn on your mobile device’s Wi
-Fi and Bluetooth:

•
Make sure the Bluetooth isn’t connected to another device, such as headphones

•
Also, make
sure the mobile
device
is
NOT

on Silent
(ringer
and
speaker
should be audible)




a. Verify that the camera’s antenna is
securely
connected.

b. Turn on your smart device’s Bluetooth and Wi
-Fi .
c. Launch the app and sign in with your Total
Connect® 2.0 account.

d. Plug
the power
supply into an AC outlet,
but:
.
DON’T
CONNECT THE POWER SUPPLY TO THE CAMERA YET!

When you do,
refer to the diagram at right

→




If your account has more than one
Location
, select the
appropriate one using the
dropdown
menu at the top of the screen.

Press
CAMERAS

at the bottom
(iOS) or top (Android)
of the
screen. (Remember that the
horizontal Navigation Order can be customized in iOS.)

a. At upper right, press
ADD CAMERA

(iOS) or

(Android)

b. Select the type
of camera you’re installing.
The names of the camera models may
vary from the illustration
at right.

c. Name
the
camera
and
press

NEXT
.
d. Connect the power supply to the camera. The
LED
at the top flashes
various
colors.
Then,
WAIT
for the camera’s LED to flash blue

only
. This
may take a couple of minutes.

e. Press
NEXT
on the app.



a. On the
Pair Your Camera
screen, press
Generate
QR
Code
. After a brief wait, the
code
appears
.
b. Show the QR code
on your device
to the camera from
3 – 8 inches
away.

If you can, keep
an eye on your device’s screen; when the code is scanned
successfully, a confirmation message will appear over the QR code.

The app will also provide
audible confirmation
via your mobile device’s speaker.

c. Select
your
Wi
-Fi network
and
press

NEXT
.
d. Enter the network password and press

NEXT
. Final setup begins.




When setup is complete,
the LED on the camera
changes from
steady blue, to purple
and finally to steady green.

The app also displays
Setup Successful
*. Press
DONE
or
ADD ANOTHER CAMERA
.

After setup, go back to the
CAMERAS
page
and check your newly
-registered camera.

Touch the
preview
image
to launch a live stream from the camera.

*The app will tell you if you need to repeat the
setup process
. This involves resetting the
camera, which is described in the app itself
.
See the other side of thi
s sheet for more information about the required steps.





WOC2
Privacy
WOC2 Resetting the Camera

If setup needs to be repeated, or to connect the camera to a different network, activate the Reset switch as seen at right.

•
To
reset
the connection, press and hold the reset button until the LED on the camera starts blinking white. Release the button immedia
tely after the LED
starts
blinking
.
•
To
join a new/different
network:

o

On the app’s
Cameras
screen, press
and delete the camera from the link on its
settings
page.

o

Press and hold the
Reset
switch to reset all settings to their factory defaults

o

Unplug the camera and then reconnect it.

o

Repeat the registration procedure.

LED STATUS INDICATOR

During installation


Blue, blinking

Power on. Ready to start setup.


Blue, steady

Connected to the app. Ready to complete setup.


Purple, steady

QR code scan is complete. Restart the Wi
-
Fi connection process.


Green, blinking

Connecting to Wi
-
Fi network.


Red, steady

Setup timed out. Unplug the camera, plug it back in and
restart setup process.

During operation


Green, blinking

Connecting to Wi
-Fi network.


Green, steady

Connected to Wi
-
Fi and operating. Note: The camera is always ready to record but only originates live streaming video when
called for by
the app
.


Red, blinking

Not connected to Wi
-Fi.

Low
-light operation is indicated by four
red LEDs arranged
around
the
lens
on the front of the camera.

More about
mounting at the

installation site

IPCAM
-WOC
2 can be wall
- or ceiling
-mounted.
The camera can be
installed
with cables running along the outside of a wall, or inside the wall. For outdoor
installations where cables are exposed to the
weather, please
protect
the cable
-ends with an enclosure such as a
weatherproof single
-gang box
, available at most
hardware stor
es. In any installation, make sure the camera’s antenna is firmly connected.

Checking
Wi
-Fi
signal
strength at the site
using the app:

•

On the
Cameras
page, touch
for
the camera you’re setting up
(on
Android
, touch
)
•

Select
Camera
Information >

•

Signal Strength
is displayed under

“IP Address”


o

60
– 100
Optimal

o

40
– 59
Marginal

o

00 – 39
Use of a Wi
-Fi range


extender strongly



recommended





Wall mount example


Ceiling mount example

(both shown with weatherproof single
-gang box)

FEDERAL COMMUNICATIONS COMMISSION &
ISED

STATEMENTS

The user shall not make
any changes or modifications to the equipment
unless
authorized by the Installation Instructions or User's
Manual. Unauthorized changes or modifications
could
void the user's
authority to operate the equipment.

CLASS B DIGITAL DEVICE STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following
statement for your information:

This equipment
generates and uses radio frequency
energy and if not installed and used
properly, that
is, in strict accordance with the manufacturer's instructions, may cause
interference to radio and television
reception. It has been type tested and found to comply
with the limits for a Class B computing
device in accordance with the specifications in Part
15 of FCC Rules, which are designed to provide
reasonable protection against
such
interference in a resident
ial installation. However, there
is no guarantee
that
interference
will not
occur in a particular installation. If this
equipment
does cause interference to radio or television
reception, which
can
be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following
measures:

•

If using an indoor antenna, have a quality
outdoor
antenna
installed.

•

Reorient the receiving
antenna
until
interference
is reduced or eliminated.

•

Move the radio or
television
receiver
away
from the receiver/control.

•

Move the antenna leads away
from
any
wire
runs to the receiver/control.

•

Plug the receiver/control into a different
outlet
so that
it and the radio or television
receiver are on different
branch
circuits.

•

Consult the dealer or an experienced radio/TV technician for help.

FCC / I
SED
STATEMENT

This device complies with Part 15 of the FCC Rules, and
ISED’s
license
-exempt RSSs
. Operation
is subject to the following
two conditions: (1) This device
may
not cause harmful
interference, and (2) This device must accept
any
interference
received, including
interference
that
may cause undesired
operation.

Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’I
SED
. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit
pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.

RF EXPOSURE
STATEMENT
:
The antenna(s) used for this
device must be installed
to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be
co-located or operating in
conjunction
with
any
other
antenna or transmitter
except in accord
ance with FCC and ISED
multi
-transmitter
product
procedures.

MISE EN GARDE EXPOSITION AUX FR
ÉQUENCES RADIO:

La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de séparation d'au moins 20 cm
(7,8 pouces) de toute personne et ne pas être située(s)
ni fonctionner parallèlement à tout autre transmetteur ou antenne, excepté en conformité avec les procédures de produit multi

transmetteur FCC et ISED.


DECLARACIÓN IFETEL
La operación de este equipo está sujeta a las siguientes dos condiciones

1. Es
posible que este equipo o dispositivo no cause interferencia perjudicial y

2.
Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su
operación no deseada.

DECLARACIÓN ANATEL

Este
equipamento opera emcarátersecundário, isto é, nãotemdireito a proteção contra
interferência prejudicial, mesmo de estações do mesmotipo, e
nãopodecausarinterferência a sistemas operando emcaráterprimário.


For the latest documentation, support and warranty information, please go to:
www.resideo.com


This product manufactured by Resideo Technologies
, Inc.

and its affiliates





2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747

2021
Resideo Technologies, Inc.
www.resideo.com

ÊR800
-
26818ALŠ

R800
-
26818A 3/21 Rev A