Resideo PROWIFIZW - Install Guide - Dated 03/19 Rev. C

1


PROWIFIZW Series

Wireless Communication Module




Installation and Setup Guide
GENERAL INFORMATION
The Communication Module allows PRO Series Control
Panels to communicate with the Central Station, PRO
Series Wireless
Touchscreens and Amazon Alexa via Wi-Fi. The PROWIF
IZW Series communications module is intended to pro
vide compatible Control
Panels with a Wi-Fi

connection as well as connection with and the abili
ty to control Z-Wave devices. The module connects d
irectly to the
Control Panel and is powered via the Control Panel’
s connection. Refer to the applicable Control Panel
's Installation and Setup Guide for
additional information.
INSTALLING THE MODULE
!

Ensure that all electrical power is removed from th
e control before installing the module. Unplug the
power supply and disconnect the backup battery.
1. Affix the provided FCC/IC label for the PROWIFIZ
W
on the control’s case back (refer to Figure 1 for
location).
2. If the Control Panel is not powered up proceed t
o step
7. If the Control Panel is powered up, disarm the
system and wait 30-60 seconds:
3. Unplug the power supply.
4. Remove the screw securing the control to the wal
l or
desk mount.
5. Remove the control from the wall or desk mount.
6. Disconnect the battery.
QS-060-V1

Figure 1. FCC/IC Label Location

7. Remove the left side cover from the control.
8. Insert the PROWIFIZW module into the slot on the
left
side of the control as shown in Figure 2 and ensure

the receptacle is securely seated on the control’s
edge connector.
9. Secure with the screw.
10. Install the left side cover.
11. Connect the battery.
12. Install the control on the wall or desk mount.
13. Plug the power supply into a 24-hour, 110VAC
unswitched outlet.

QS-058-V0
COVER
PROWIFIZW
MODULE
SCREW

Figure 2. Installing the PROWIFIZW Module


Programming
Note:
The PROWIFIZW requires a router and internet servi
ce for Wi-Fi connection.
1. Programming associated with the PROWIFIZW module
as well as the inclusion/exclusion of Z-Wave devic
es is conducted through
the AlarmNet 360™ Programming Tool. On a laptop, PC
or Smart Device, go to www.alarmnet360.com.
2. When programming is complete, perform a Communic
ations Test. SPECIFICATIONS
Board Dimensions: ................................
...................................................
...................................................
......... 1.625” W x 2.625” L x 0.3125” D
Input Voltage Range: .............................
...................................................
...................................................
........................... 3.6 – 14V, Max 17V
Input Voltage: ...................................
...................................................
...................................................
...................................................
...... 3.5V
Current Drain: ...................................
...................................................
...................................................
...................................................
. 250mA
Temperature: .....................................
...................................................
...................................................
.................... 32°F (0°C) to 140°F (60°C)


REFER TO THE INSTALLATION AND SETUP GUIDE FOR THE C
ONTROL WITH WHICH THIS DEVICE IS USED FOR WARRANTY
INFORMATION AND LIMITATIONS OF THE ENTIRE SYSTEM.


FEDERAL COMMUNICATIONS COMMISSION & ISED STATEMENTS

The user shall not make any changes or modification
s to the equipment unless authorized by the Install
ation Instructions or User's Manual. Unauthorized c
hanges or
modifications could void the user's authority to op
erate the equipment.
FCC CLASS B STATEMENT
This equipment has been tested to FCC requirements
and has been found acceptable for use. The FCC requ
ires the following statement for your information:
This equipment generates and uses radio frequency e
nergy and if not installed and used properly, that
is, in strict accordance with the manufacturer's in
structions, may cause
interference to radio and television reception. It
has been type tested and found to comply with the l
imits for a Class B computing device in accordance
with the specifications in
Part 15 of FCC Rules, which are designed to provide
reasonable protection against such interference in
a residential installation. However, there is no g
uarantee that
interference will not occur in a particular install
ation. If this equipment does cause interference to
radio or television reception, which can be determ
ined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
• If using an indoor antenna, replace it with a qua
lity outdoor antenna.
• Reorient the receiving antenna until interference
is reduced or eliminated.
• Move the radio or television receiver away from t
he receiver/control.
• Move the antenna leads away from any wire runs to
the receiver/control.
• Plug the receiver/control into a different outlet
so that it and the radio or television receiver ar
e on different branch circuits.
• Consult the dealer or an experienced radio/TV tec
hnician for help.
Responsible Party / Issuer of Supplier’s Declaratio
n of Conformity: Ademco Inc., a subsidiary of Resid
eo Technologies, Inc., 2 Corporate Center Dr., Melv
ille, NY 11747, Ph:
516-577-2000.
ISED CLASS B STATEMENT
This Class B digital apparatus complies with Canadi
an ICES-003.
Cet appareil numérique de la classe B est conforme
à la norme NMB-003 du Canada.
FCC / ISED STATEMENT
This device complies with Part 15 of the FCC Rules,
and ISED’s license-exempt RSSs. Operation is subje
ct to the following two conditions: (1) This device
may not cause
harmful interference (2) This device must accept an
y interference received, including interference tha
t may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles
de la FCC et exempt de licence RSS d’ISED. Son fon
ctionnement est soumis aux conditions suivantes: (1
) Cet appareil ne
doit pas causer d’interférences nuisibles. (2) Cet
appareil doit accepter toute interférence reçue y c
ompris les interférences causant une réception indé
sirable.

!

RF Exposure Warning
The antenna(s) used for this transmitter must be in
stalled to provide a separation distance of at leas
t 7.8 inches (20 cm) from all persons and
must not be co-located or operating in conjunction
with any other antenna or transmitter except in acc
ordance with FCC and ISED multi-
transmitter product procedures.
Mise en Garde
Exposition aux Frequences Radio: La/les antenne(s)
utilisée(s) pour cet émetteur doit/doivent être ins
tallée(s) à une distance de séparation
d'au moins 20 cm (7,8 pouces) de toute personne et
ne pas être située(s) ni fonctionner parallèlement
à tout autre transmetteur ou antenne,
excepté en conformité avec les procédures de produi
t multi transmetteur FCC et ISEDs.

The product should not be disposed of with other ho
usehold waste. Check for the nearest authorized col
lection centers or authorized recyclers. The correc
t disposal
of end-of-life equipment will help prevent potentia
l negative consequences for the environment and hum
an health.
Any attempt to reverse-engineer this device by deco
ding proprietary protocols, de-compiling firmware,
or any similar actions is strictly prohibited.

USE OF THESE PRODUCTS IN COMBINATION WITH NON-RESID
EO PRODUCTS IN A WIRELESS MESH NETWORK, OR TO ACCES
S, MONITOR OR CONTROL DEVICES IN A WIRELESS MESH
NETWORK VIA THE INTERNET OR ANOTHER EXTERNAL WIDE A
REA NETWORK, MAY REQUIRE A SEPARATE LICENSE FROM SI
PCO, LLC. FOR MORE INFORMATION, CONTACT SIPCO, LLC
OR IPCO, LLC AT 8215 ROSWELL RD., BUILDING 900, SUI
TE 950, ATLANTA, GA 303350, OR AT WWW.SIPCOLLC.COM
OR WWW.INTUSIQ.COM

SUPPORT & WARRANTY INFORMATION
For the latest documentation, support and warranty
information, please go to:
www.resideo.com





This product manufactured by Resideo Technologies,
Inc. and its affiliates




2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747

2021 Resideo Technologies, Inc.
www.resideo.com


800-25179C 3/19 Rev. C