SiXCT Installation Guide

SiXTM Series

SiXCT

Installation Instructions

The SiXCT is a wireless door / window sensor
intended for use with Honeywell controls that
support SiX™ series devices.

(4)
#6 x 3/4”

(2)
#4 x 5/8”

Open the SiXCT

Terminal Block

• Firmly slide the top and bottom housings in
opposite directions and pull them apart to open
the device.

Reed
Switch

Magnet

LED
Tamper
Switch

Mounting
The SiXCT can be mounted with several options:
• Installation with magnet: Make gap is 0.75";
Break gap is 1.30".
• Optional Wiring for Service loops:
a) surface wiring
b) concealed wiring
NOTE: Wiring limit is 3ft.
NOTE: After enrolling and before mounting the
device permanently, conduct Go/No Go tests (see
controller’s instructions) to verify adequate signal
strength. Adjust the device location and orientation
as necessary.

*

*

*

*
*
*Optional

Programming Mode > Zones >
Add New > Serial Number

Enroll and Set Up
NOTE: The SiXCT can be enrolled and programmed
before or after installation.
1. Set the Lyric Controller in Programming Mode and
go to Zone Programming. Select Add New, then
Serial Number. Follow the controller’s instructions
to begin enrollment.
2. Pull the battery tab to activate the SiXCT and begin
the enrollment process.
3. The LED flashes (up to about 20 seconds*) during
enrollment.
• The device sends its unique MAC ID (Serial
Number) and Services information to the
controller.
• The controller registers the device and displays
the transmitter data on screen.

1

Serial Number

Loop Number

Zone Description 1

Zone Description 2

Device Type

Alarm Report

Panic

Response Type

Chime

Supervision

Home

PU
CON LL TO
NEC
T

3

0
10
45
20
30

The LED
Flashes; wait
up to about 20
seconds*

PU
CON LL TO
NEC
T

2

*NOTE: Enrollment time varies depending on the
signal strength between the device and the controller.

4. When done, the LED is ON for 3 seconds and the
control beeps to confirm enrollment.
5. Trigger the device again to complete enrollment
and select SAVE.
If the device is not successfully enrolled during the
enrollment period, the LED turns off and the device
powers down. Activate a tamper, wired service (loop)
or the reed switch to restart the enrollment process.

4
LED ON for
3 seconds

The device can also be manually enrolled. See the
Controller’s Programming Guide for details.
Follow instructions in the Controller’s programming
guide to program the SiXCT services (the default
service is “Reed”):
• Reed switch / Magnet
• External device connected / Terminal block
(unsupervised)

Trigger the device
again to complete
enrollment and
select SAVE

After enrolling, update the SiXCT firmware (via the
Controller) to ensure the latest version is used. See
the Controller’s instructions.

NOTE: Once enrolled in a system, the SiXCT cannot be used
with another controller until it is removed from the current
controller. See the Controller’s instructions for details.

Battery Replacement
• Push the bottom latch of the mounting
bracket back to disengage it. Then slide the
back housing, up and out to remove it from
the mounting bracket.
• Slide the front and back housings in opposite
directions and pull the housings apart.
• Remove the battery, wait 10 seconds, then
insert a new battery. Recommended
batteries:
Panasonic CR123A
Honeywell 466
Duracell DL123
Duracell DL123A
• Place the front and back housings together
and slide them together as shown.
BATTERY CAUTION: Risk of fire, explosion and burns.
Do not recharge, disassemble, heat above 212° F (100° C)
or incinerate. Dispose of used batteries properly. Keep
away from children.

5

Wait 10
seconds
0
10
45
30

Honeywell 466
Duracell DL123
Duracell DL123A
Panasonic CR123A

Specifications:

Approval Listings:

Battery: 1 x 3V Lithium, Honeywell 466, Panasonic CR123A, Duracell DL123
or DL123A
Tamper: Cover and Wall
RF Frequency: 2.4GHz
Operating Temperature: 32° – 122° F / 0° – 50° C
(Agency Compliance 32° – 120° F / 0° – 49° C)
Relative Humidity: 95% max. (Agency Compliance - 93% max.),
non-condensing
Dimensions: 1” H x 3.13” L x 1.61” W / 25.5 mm H x 79.5 mm L x 41 mm W

FCC / IC
cETLus Listed
Conforms to UL 634
Certified to ULC/ORD-C634
Other Standards:
RoHS
Product must be tested at
least once each year

FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's
Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following
statement for your information: This equipment generates and uses radio frequency energy and if not installed and used properly, that
is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type
tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules,
which are designed to provide reasonable protection against such interference in a residential installation. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including
interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis
aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence
reçue y compris les interférences causant une reception indésirable.
RF EXPOSURE
Warning – The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm)
from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance
with FCC multi-transmitter product procedures.
Mise en Garde
Exposition aux Frequences Radio: L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de séparation d'au
moins 7,8 pouces (20 cm) de toutes les personnes.

Support and Warranty
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING
LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

For the latest documentation and online support information, please go to:
https://mywebtech.honeywell.com/
For the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa.
For patent information, see www.honeywell.com/patents

 2014 Honeywell International Inc. Honeywell and is a
registered trademark of Honeywell International Inc.
All other trademarks are the properties of their respective
owners. All rights reserved.

MyWebTech

Warranty

Patents

2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
www.honeywell.com/security

DOC CODE 128B BAR CODE HERE
800-21338 11/15 Rev A